CASE IH 4WD tractor 9370, 9380, 9390
CASE IH 4WD tractor 9370, 9380, 9390 — parts list, part 1 of 4
2,937 part numbers across 1 assemblies, transcribed from the catalogue above and split over 4 pages. Search a page for a part number to find the assembly it belongs to; the page links are below the list.
Parts list
| Pos | Part no. | Qty | Description |
|---|---|---|---|
| 1 | 90-8369T1 | 1 | RADIATOR – engine cooling, 9370 tractor, replaces 90-7675T1 radiator |
| 1 | 90-8263T1 | 1 | RADIATOR – engine cooling, 9380 tractor, replaces 90-7674T1 radiator |
| 2 | 90-7680T1 | 1 | SHROUD – fan, prior to P.I.N. JEE003660 |
| 2 | 90-8363T2 | 1 | SHROUD – fan, P.I.N. JEE003660 and after |
| 3 | 426-410 | 10 | BOLT – hex, 1/4 NC x 5/8 inch, grade 8 |
| 4 | 495-21031 | 10 | WASHER – flat, 5/16 x 3/4 x 1/16 inch |
| 5 | 90-7701T1 | 1 | TANK – fill, radiator, See Figure 2-04 for service parts |
| 6 | 426-824 | 2 | BOLT – hex, 1/2 NC x 1-1/2 inch, grade 8 |
| 7 | 19-961 | 2 | WASHER – flat |
| 8 | 426-836 | 2 | BOLT – hex, 1/2 NC x 2-1/4 inch, grade 8 |
| 9 | 231-1448 | 6 | NUT – hex, self-locking, 1/2 inch NC |
| 10 | L13142 | 2 | MOUNT – isolator, rubber |
| 11 | 90-7598T1 | 2 | SUPPORT – radiator |
| 12 | 90-7683T1 | 1 | PLATE – mounting, radiator |
| 13 | 70-2987T1 | 1 | SEAL – formed rubber, adhesive-backed, 3302 mm (130 inch) long, cut from F43117X bulk seal, see |
| 14 | 90-6832T1 | 1 | SEAL – formed rubber, 1124 mm (44-1/4 inch) long, cut from L107724 bulk seal, see below |
| 15 | 426-610 | 10 | BOLT – hex, 3/8 NC x 5/8 inch, grade 8 |
| 16 | 495-11041 | 10 | WASHER – flat, 13/32 x 13/16 x 1/16 inch |
| 17 | 70-5265T1 | 1 | SEAL – foam, 711 mm (28 inch) long, cut from 70-5259T1X bulk seal, see below |
| 19 | 495-21050 | 2 | WASHER – flat, 1/2 x 1-1/4 x 5/64 inch |
| 20 | 426-848 | 2 | BOLT – hex, 1/2 NC x 3 inch, grade 8 |
| 21 | 19-961 | 2 | WASHER – flat, 1/2 x 1-3/4 x 1/8 inch |
| 22 | 47-4208 | 2 | MOUNT – insulator, rubber |
| 23 | 495-11034 | 8 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 24 | 426-512 | 8 | BOLT – hex, 5/16 NC x 3/4 inch, grade 8 |
| 28 | 70-5265T1 | 1 | SEAL – foam, 711 mm (28 inch) long, cut from 70-5259T1X bulk seal, see below |
| 29 | 70-5848T1 | 1 | TRIM – edge, 140 mm (5-1/2 inch) long, cut from F64277X bulk trim, see below |
| 1 | 90-8369T1 | 1 | RADIATOR – engine cooling, 9370 tractor, replaces 90-7675T1 radiator |
| 1 | 90-8263T1 | 1 | RADIATOR – engine cooling, 9380 tractor, replaces 90-7674T1 radiator |
| 2 | 217-92 | 1 | VALVE – drain, 1/4 inch PT, replaces H434809 valve |
| 3 | 90-7693T2 | 1 | HOSE – radiator, lower |
| 4 | 19-135 | 2 | STRAP – tie, nylon |
| 6 | 70-5522T1 | 1 | CLAMP – adj, 2-13/16 – 3-3/4 inch dia |
| 7 | 70-5521T1 | 3 | CLAMP – adj, 2 – 3 inch dia |
| 8 | 90-6822T2 | 1 | HOSE – radiator, upper, prior to P.I.N JEE0036501 |
| 8 | 90-8051T1 | 1 | HOSE – radiator, upper, P.I.N. JEE0036501 and after |
| 9 | 214-1404 | 6 | CLAMP – adj, 1/4 – 5/8 inch dia |
| 12 | 90-7701T1 | 1 | TANK – fill, radiator |
| 13 | 90-7731T1 | 1 | CAP – radiator |
| 14 | 217-120 | 1 | ADAPTER – straight, 1/4 barb end x 1/8 inch PT |
| 15 | 31-3063 | 1 | HOSE – 406 mm (16 inch) long, cut from A21561X bulk hose, see below |
| 16 | 214-1404 | 6 | CLAMP – adj, 1/4 – 5/8 inch dia, replaces 214-1404 clamp |
| 17 | 217-292 | 2 | ELBOW – 90 degree, 1/4 barb end x 1/8 inch PT |
| 18 | 31-2742 | 1 | HOSE – 533 mm (21 inch) long, cut from A21561X bulk hose, see below |
| 19 | 90-6818T1 | 1 | NECK – filler, prior to P.I.N JEE0036501 |
| 20 | 90-8326T1 | 1 | NECK – filler, P.I.N. JEE0036501 and after |
| 21 | 426-512 | 8 | BOLT – hex, 5/16 NC x 3/4 inch, grade 8 |
| 22 | 495-11034 | 8 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 24 | 31-1503 | 1 | HOSE – 711 mm (28 inch) long, cut from 31-1502 bulk hose, see below |
| 25 | 214-1420 | 2 | CLAMP – adj, 13/16 – 1-3/4 inch dia |
| 26 | 217-156 | 1 | ADAPTER – straight, 1 inch stem end x PT |
| 27 | 31-2835 | 1 | HOSE – 1499 mm (59 inch) long, cut from 31-2855 bulk hose, prior to P.I.N. JEE0036501, see below |
| 27 | A172261 | 1 | HOSE – 1800 mm (70-7/8 inch) long, cut from L126767 bulk hose, P.I.N. JEE0036501 and after, see |
| 28 | 217-119 | 1 | ADAPTER – straight, 1/4 barb end x 1/4 inch PT |
| 30 | 90-8351T1 | 1 | BRACKET – mounting |
| 32 | 515-23127 | 1 | CLAMP – P-type, 1/2 inch ID, hose, overflow |
| 33 | 90-7763T1 | 1 | BRACKET – tank mounting |
| 34 | 31-3065 | 1 | HOSE – 203 mm (8 inch) long, cut from 87769CX bulk hose, coolant recovery overflow |
| 35 | 90-7717T1 | 1 | BOTTLE – coolant recovery |
| 36 | 1547924C1 | 1 | CAP – recovery bottle |
| 37 | 22-824 | 1 | STRAP – tie, 7 inch |
| 38 | 414-916 | 1 | BOLT – hex, 9/16 NF x 1 inch |
| 39 | 495-21056 | 1 | WASHER – flat, 9/16 x 1-3/8 x 7/64 inch |
| 40 | 414-68 | 1 | BOLT – hex, 3/8 NF x 1/2 inch |
| 41 | 495-11041 | 1 | WASHER – flat, 13/32 x 13/16 x 1/16 inch |
| 1 | 90-7779T91 | 1 | CLEANER ASSEMBLY – air, engine, Includes: precleaner and mounting parts, prior to P.I.N. |
| 1 | 90-8298T91 | 1 | CLEANER ASSEMBLY – air, engine, Includes: precleaner and mounting parts, P.I.N. JEE0036501 and |
| 2 | 426-616 | 4 | BOLT, Hex, 3/8″-16 x 1″, G8, Full Thd |
| 4 | 231-4136 | 7 | NUT – hex, self-locking, 3/8 inch NC |
| 5 | 214-32120 | 2 | CLAMP – adj, 6-3/4 – 7-5/8 inch dia |
| 7 | 90-3869T1 | 1 | TUBE – air inlet |
| 8 | 60-2764T1 | 1 | CLAMP – support |
| 9 | 413-520 | 1 | BOLT – hex, 5/16 NC x 1-1/4 inch |
| 10 | 425-105 | 1 | NUT – hex, 5/16 inch NC |
| 13 | 90-6870T1 | 1 | BRACKET – support, air inlet tube |
| 14 | D52276 | 3 | INSULATOR – rubber, brace |
| 15 | 426-628 | 3 | BOLT – hex, 3/8 NC x 1-3/4 inch, grade 8 |
| 16 | 495-21044 | 9 | WASHER – flat, 7/16 x 1 x 5/64 inch |
| 17 | 9-120 | 1 | CAP – air inlet |
| 20 | 214-32104 | 6 | CLAMP – adj, 5-3/4 – 6-5/8 inch dia |
| 21 | 90-6892T1 | 1 | ELBOW – 70 degree |
| 22 | 90-8052T1 | 1 | TUBE – air intake, prior to P.I.N. JEE0036501 |
| 22 | 90-8123T1 | 1 | TUBE – air intake, P.I.N JEE0036501 and after |
| 24 | 90-6895T1 | 1 | TUBE – air intake, 387 mm (15-1/4 inch) long |
| 27 | 44-13T1 | 1 | U-BOLT – tube |
| 28 | 495-11034 | 2 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 29 | 231-1445 | 2 | NUT – hex, self-locking, 5/16 inch NC |
| 32 | 214-1436 | 2 | CLAMP, HOSE, #36, 1.81/2.75 Type F Worm, Adj |
| 33 | 90-3979T1 | 1 | HOSE – aspirator, air cleaner to exhaust |
| 35 | 90-3871T1 | 2 | CLAMP – band, air cleaner mounting |
| 38 | 1983233C1 | 1 | SWITCH – restriction, air cleaner |
| 2 | 90-8302T1 | 1 | COVER – end, replaces 134610A1 cover, Ref: 2, 7 & 10 do not replace numbers shown – the alternate |
| 7 | 90-8300T1 | 1 | ELEMENT – primary, replaces 132151A1 element, Ref: 2, 7 & 10 do not replace numbers shown – the |
| 9 | 90-8301T1 | 1 | ELEMENT – secondary, replaces 132149A1 element |
| 10 | 9-120 | 1 | CAP – air inlet, Ref: 2, 7 & 10 do not replace numbers shown – the alternate numbers shown will be for |
| 11 | 90-4207T1 | 1 | PRECLEANER ASSEMBLY – engine, Includes: Ref. 12 & 13 |
| 12 | 413-632 | 2 | BOLT – hex, 3/8 NC x 2 inch |
| 13 | 425-106 | 2 | NUT, 3/8″-16, G5 |
| 14 | 90-4208T1 | 1 | ADAPTER – intake reducer |
| 15 | 90-3871T1 | 2 | CLAMP – band, air cleaner mounting |
| 16 | 413-528 | 1 | BOLT – hex, 5/16 NC x 1-3/4 inch |
| 17 | 27254R1 | 1 | NUT – hex, 5/16 inch NC, grade 8 |
| 1 | A143381 | 1 | SOLENOID ASSEMBLY – ether injection, no longer available, order 185552A2 solenoid assembly |
| 2 | D77648 | 1 | HANGER – ether can, order 18552A2 hanger |
| 3 | 395686R1 | 1 | GASKET – injector solenoid, 15/64 inch diameter |
| 4 | 222-615 | 1 | ELBOW – 90 degree, compression, 1/8 tube OD x 1/8 inch PT, Includes: Ref. 5 & 6 |
| 5 | 222-650 | 1 | SLEEVE – tapered, 1/8 inch tube OD |
| 6 | 222-660 | 1 | NUT – hex, 1/8 tube OD x 5/16-24 inch |
| 8 | 190752A1 | 1 | HOUSING – ether injection solenoid |
| 9 | 31-1347 | 1 | TUBE – 610 mm (24 inch) long, cut from 29-53T2 bulk tube, see below, ether solenoid to injector |
| 10 | 60-7166T2 | 1 | HARNESS – engine, replaces 60-7166T1 harness |
| 11 | 19-135 | 1 | STRAP – tie, nylon |
| 12 | 221-84 | 1 | REDUCER – pipe, 1/4 male x 1/8 inch female, P.I.N. JEE0036501 and after |
| 13 | 90-7034T1 | 1 | INJECTOR ASSEMBLY – nozzle, Includes: Ref. 14 & 15 |
| 14 | 222-650 | 1 | SLEEVE – tapered, 1/8 inch tube OD |
| 15 | 222-660 | 1 | NUT – hex, 1/8 tube OD x 5/16-24 inch |
| 16 | 425-105 | 2 | NUT – hex, 5/16 inch NC |
| 18 | 1964751C1 | 1 | SWITCH – rocker, ether start |
| 19 | 426-512 | 2 | BOLT – hex, 5/16 NC x 3/4 inch, grade 8 |
| 20 | 425-105 | 2 | NUT – hex, 5/16 inch NC |
| 22 | 492-11031 | 2 | WASHER, LOCK, 5/16″ |
| 23 | 90-7645T1 | 1 | BRACKET – mounting, solenoid, if used, prior to P.I.N. JEE0036501, replaces 90-7336T1 bracket |
| 24 | 90-8367T1 | 1 | BRACKET – mounting, ether, P.I.N. JEE0036501 and after, replaces 90-8352T1 bracket, Includes: Ref. |
| 25 | 495-11041 | 2 | WASHER – flat, 13/32 x 13/16 x 1/16 inch |
| 28 | 495-11034 | 2 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 29 | 493-41033 | 1 | WASHER – external tooth lock, 5/16 inch |
| 1 | 90-7608T2 | 1 | MUFFLER – exhaust, engine, prior to P.I.N. JEE0036501 |
| 2 | 90-8295T1 | 1 | MUFFLER – exhaust, engine, P.I.N. JEE0036501 and after |
| 4 | 426-616 | 3 | BOLT, Hex, 3/8″-16 x 1″, G8, Full Thd |
| 5 | 492-11038 | 3 | WASHER, LOCK, 3/8″ |
| 6 | 232-4136 | 7 | NUT, LOCK, 3/8″-16, GC |
| 7 | 90-8320T1 | 3 | CLAMP – exhaust |
| 8 | 90-7692T1 | 1 | TUBE – exhaust, prior to P.I.N. JEE0036501 |
| 8 | 90-8124T1 | 1 | TUBE – exhaust, P.I.N. JEE0036501 and after |
| 9 | 90-5776T1 | 1 | TUBE – elbow, exhaust |
| 10 | 31-1316 | 1 | CLAMP – exhaust |
| 14 | 32-322T1 | 1 | U-BOLT – 3/8 inch NC |
| 15 | 32-323T1 | 1 | SADDLE – clamp, U-bolt |
| 16 | 90-7100T1 | 1 | BRACKET – clamp mounting |
| 17 | 495-11041 | 4 | WASHER – flat, 13/32 x 13/16 x 1/16 inch |
| 18 | 426-612 | 2 | BOLT – hex, 3/8 NC x 3/4 inch, grade 8 |
| 21 | 90-7815T1 | 1 | CLAMP – adjustable |
| 22 | 426-620 | 1 | BOLT – hex, 3/8 NC x 1-1/4 inch, grade 8 |
| 23 | 231-1446 | 1 | NUT, LOCK, 3/8″-16, GB |
| 24 | 90-7725T1 | 1 | TUBE – aspirator |
| 25 | 19-1049 | 1 | U-BOLT – 5/16 inch NC |
| 26 | 495-11034 | 2 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 27 | 231-1445 | 2 | NUT – hex, self-locking, 5/16 inch NC |
| 28 | 45-177 | 1 | TUBE – flex, exhaust |
| 6 | 90-3491T1 | 1 | CABLE – heater |
| 7 | 19-135 | 1 | STRAP – tie, nylon, if used |
| 2 | 90-8264T1 | 1 | BELT – V-type, set of two |
| 3 | 90-2383T1 | 1 | BELT – V-type, ribbed, water pump, 90-2383t1 water pump belt is a 6 rib belt and has an effective |
| 4 | 90-7101T1 | 1 | FILTER – engine oil |
| 7 | A77544 | 1 | FILTER – water conditioning, precharge, service |
| 8 | 90-3941T1 | 1 | FILTER – fuel |
| 9 | A77424 | 1 | CAP – oil fill tube, not shown |
| 10 | 90-1375T1 | 1 | BELT – alternator, set of two, used on the 9370 and 9380 |
| 11 | 236987A1 | 1 | FAN – engine, used on 9390 |
| 15 | 428-1024 | 9 | BOLT – hex, 5/8 NF x 1-1/2 inch, grade 8 |
| 16 | 90-7553T1 | 1 | HOUSING – flywheel, replaced by 229656A3 mount, Ref. 17 |
| 17 | 229656A3 | 1 | MOUNT – engine, replaces 90-7553T1 housing, Ref. 16 |
| 21 | 426-1064 | 2 | BOLT – hex, 5/8 NC x 4 inch, grade 8 |
| 22 | 19-408 | 2 | WASHER – flat, 5/8 x 2-1/2 x 3/16 inch |
| 23 | 24-231 | 2 | INSULATOR – engine mount, rubber, front |
| 24 | 51-128 | 2 | WASHER – flat, 5/8 x 3-1/2 x 3/16 inch |
| 25 | 496-81022 | 2 | WASHER – flat, 21/32 x 1-1/4 x 1/4 inch, hardened |
| 26 | 232-41110 | 2 | NUT, LOCK, 5/8″-11, GC |
| 30 | 90-3569T1 | 1 | SPACER – fan |
| 31 | 90-4238T1 | 1 | FAN – engine, prior to P.I.N. JEE0036501, used on 9370 and 9380 |
| 31 | 90-8164T1 | 1 | FAN – engine, P.I.N. JEE0036501 and after, used on 9370 and 9380 |
| 32 | 326-856 | 6 | BOLT, Hex, 1/2″-13 x 3 1/2″, G8 |
| 33 | 90-8378T1 | 1 | CLUTCH – fan, used on 9390, Only the 9380 QT and the 9390 have the viscus fan and require this |
| 34 | 496-21034 | 6 | WASHER, 11/32″ x 11/16″ x 0.89″, HDN, Used with 90-8378T1 clutch, Ref. 33 |
| 35 | 825-1408 | 6 | Nut, M8, Cl 8, Used with 90-8378T1 clutch, Ref. 33 |
| 36 | 107717A1 | 1 | STARTER ASSEMBLY – Delco Remy, 12 volt, parts list Figures 4-38 and 4-40 |
| 37 | 19-912 | 3 | WASHER – flat, 21/32 ID x 1-3/16 OD x 3/16 inch thick |
| 38 | 80-11032 | 3 | BOLT – 12 point flange, 5/8 NC x 2 inch, grade 8, Three screws are required to install the starter (the |
| 39 | 425-108 | 6 | NUT – hex, 1/2 inch NC, used with 90-8378T1 clutch, Ref. 33 |
| 40 | 426-12120 | 2 | BOLT – hex, 3/4 NC x 7-1/2 inch, grade 8 |
| 41 | 496-11081 | 2 | WASHER – flat, 13/16 x 1-1/2 x 9/64 inch, hardened |
| 42 | 47-4172 | 2 | INSULATOR – mount, rubber, rear |
| 43 | 495-21081 | 2 | WASHER – flat, 13/16 x 2 x 9/64 inch |
| 44 | 19-85 | 2 | NUT – hex, self-locking, 3/4 inch NC |
| 45 | 19-6150 | 2 | WASHER – flat, special |
| 46 | 229656A3 | 1 | MOUNT – engine |
| 47 | 90-8383T1 | 1 | BELT – alternator, used on the 9390 |
| 48 | 90-8396T1 | 6 | STUD – fan |
| 49 | 90-8400T1 | 1 | BELT – fan, used on the 9390 |
| 50 | 238-5041 | 1 | O-RING, -041, 70 Duro, 2.989″ ID x .070″ Thk, Seal clutch |
| 1 | 31-2967 | 1 | HOSE – 4369 mm (172 inch) long, cut from 50-3418X1 bulk hose, see below |
| 2 | 31-2951 | 1 | HOSE – 4648 mm (183 inch) long, cut from 50-3418X1 bulk hose, see below |
| 3 | 31-2976 | 3 | ADAPTER – straight, 7/8-14 female swivel x 31/64 inch barb |
| 4 | 218-1561 | 1 | ADAPTER – straight, 3/4-16 swivel x 1/2 inch female PT |
| 5 | 31-2966 | 1 | ADAPTER – straight, special |
| 6 | 218-445 | 2 | ADAPTER – straight, 7/8-14 flare x 1/2 inch PT |
| 7 | 22-824 | 1 | STRAP – tie, 7 inch |
| 8 | 218-5232 | 1 | ELBOW – 90 degree, 7/8-14 inch flare x swivel |
| 9 | 31-1267 | 2 | VALVE – shutoff |
| 10 | 515-23238 | 5 | CLAMP – P-type, 15/16 inch ID |
| 11 | 426-516 | 1 | BOLT – hex, 5/16 NC x 1 inch, grade 8 |
| 12 | 425-106 | 1 | NUT, 3/8″-16, G5 |
| 13 | 425-105 | 3 | NUT – hex, 5/16 inch NC |
| 14 | 218-485 | 1 | ELBOW – 90 degree, 7/8-14 flare x 1/2 inch PT |
| 15 | 31-1000 | 1 | TEE – 1/2 female PT x 1/2 male PT x 7/8 NF inch flare |
| 16 | 515-25254 | 1 | CLAMP, 1″, Insul, 1/2″ Bolt, P-type, Used on the 9370 and 9380 |
| 17 | 495-11053 | 1 | WASHER, 1/2″, SAE (17/32″ x 1-1/16″ x 3/32″) |
| 18 | 426-812 | 1 | BOLT – hex, 1/2 NC x 3/4 inch, grade 8 |
| 19 | 231-1445 | 2 | NUT – hex, self-locking, 5/16 inch NC |
| 20 | 217-1226 | 1 | ELBOW – 90 degree, 1/2-14 inch NPT |
| 21 | 90-7508T1 | 1 | TUBE – fuel, tank |
| 22 | A162191 | 1 | CAP – fuel |
| 23 | 90-7732T1 | 1 | BREATHER – fuel tank |
| 24 | 50-2534T1 | 6 | CLAMP – split, one-half, replaces 50-2551T1 clamp |
| 25 | 50-2533T1 | 2 | PLATE – clamp support |
| 26 | 426-540 | 1 | BOLT – hex, 5/16 NC x 2-1/2 inch, grade 8 |
| 27 | 495-21038 | 2 | WASHER – flat, 3/8 x 7/8 x 3/32 inch |
| 28 | 90-3941T1 | 1 | FILTER – fuel |
| 29 | 217-196 | 1 | NIPPLE – straight, 1/2 PT x 1-13/16 inch |
| 1 | 60-6831T91 | 1 | SENSOR – fuel |
| 2 | 104812C3 | 1 | GASKET – fuel level sender |
| 3 | 463-3108 | 5 | SCREW – machine, hex washer head, No. 10 NC x 1/2 inch |
| 1 | 60-4686T2 | 1 | LEVER – throttle control |
| 2 | 60-3783T1 | 1 | BELLCRANK – throttle control |
| 3 | 426-412 | 4 | BOLT – hex, 1/4 NC x 3/4 inch, grade 8 |
| 4 | 111626C1 | 6 | NUT – hex, self-locking, special, 1/4 inch NC |
| 5 | 426-416 | 2 | BOLT – hex, 1/4 NC x 1 inch, grade 8 |
| 6 | 60-2050T3 | 1 | KNOB – control lever |
| 7 | 19-5798 | 1 | SCREW – set, No. 8 NC |
| 8 | 60-3696T1 | 1 | LEVER – bellcrank |
| 9 | 19-6113 | 3 | BUSHING – nylon, split, flanged |
| 10 | 60-7066T1 | 1 | PEDAL – decelerator |
| 11 | 1999381C1 | 1 | PAD – pedal, replaces 1958503C1 pad |
| 12 | 495-21044 | 4 | WASHER – flat, 7/16 x 1 x 5/64 inch |
| 13 | 432-816 | 2 | 1/8″ x 1″ |
| 14 | 60-6278T1 | 1 | ROD – actuating |
| 17 | 60-6277T2 | 1 | BRACKET – retaining |
| 18 | 60-6276T1 | 1 | LEVER – decelerator |
| 19 | 60-1948T1 | 2 | BUSHING – flange |
| 20 | 19-5995 | 2 | WASHER – spring, 5/16 inch |
| 21 | 19-5664 | 1 | PIN – clevis, 5/16 x 2 inch |
| 22 | 32-612 | 1 | PIN, SPLIT (COTTER), 3/32″ x 3/4″ |
| 23 | 426-820 | 1 | BOLT – hex, 1/2 NC x 1-1/4 inch, grade 8 |
| 24 | 38-11216 | 1 | PIN, 3/16″ x 1″, Slotted |
| 25 | 24-206 | 2 | BUSHING – flange |
| 26 | 19-490 | 1 | COLLAR – locking |
| 27 | 60-4926T1 | 1 | ROD – pedal, decelerator |
| 30 | 60-3702T1 | 1 | SPRING – compression |
| 34 | 60-6425T1 | 1 | CABLE – throttle, Includes: Ref. 35 |
| 35 | 225-14210 | 1 | NUT, #10-32 |
| 40 | H433283 | 1 | JOINT – ball |
| 41 | 163-55 | 1 | SCREW – machine, hex head, No. 10 NC x 1-1/4 inch |
| 42 | 90-7749T1 | 1 | SPACER – joint |
| 43 | 495-31025 | 1 | WASHER – flat, 1/4 x 9/16 x 3/64 inch |
| 44 | 86625057 | 1 | NUT, LOCK, #10-24, GB |
| 1 | 60-5850T1 | 1 | LEVER – throttle control |
| 2 | 60-5851T1 | 1 | PLATE – mounting, throttle control |
| 3 | 426-412 | 2 | BOLT – hex, 1/4 NC x 3/4 inch, grade 8 |
| 4 | 111626C1 | 2 | NUT – hex, self-locking, special, 1/4 inch NC |
| 5 | 426-828 | 1 | BOLT – hex, 1/2 NC x 1-3/4 inch, grade 8 |
| 6 | 495-21056 | 2 | WASHER – flat, 9/16 x 1-3/8 x 7/64 inch |
| 7 | 54-294 | 2 | WASHER – flat, 1/2 x 1-3/8 x 1/8 inch |
| 8 | 19-5648 | 3 | SPRING – Belleville, 1/2 inch |
| 9 | 231-1448 | 1 | NUT – hex, self-locking, 1/2 inch NC |
| 12 | 60-2050T3 | 1 | KNOB – control lever |
| 13 | 19-5798 | 1 | SCREW – set, No. 8 NC |
| 17 | 60-6532T1 | 1 | BRACKET – retaining, cable |
| 18 | 495-11034 | 2 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 19 | 425-105 | 2 | NUT – hex, 5/16 inch NC |
| 20 | 60-6424T1 | 1 | CABLE – throttle, Includes: Ref. 21 |
| 21 | 225-14210 | 1 | NUT, #10-32 |
| 25 | 22-609 | 1 | GROMMET – cable |
| 27 | 163-55 | 1 | SCREW – machine, hex head, No. 10 NC x 1-1/4 inch |
| 28 | H433283 | 1 | JOINT – ball |
| 29 | 90-7749T1 | 1 | SPACER – throttle |
| 30 | 86625057 | 1 | NUT, LOCK, #10-24, GB |
| 1 | 515-2395 | 1 | CLAMP, 3/8″, Insul, 3/8″ Bolt |
| 2 | 414-916 | 2 | BOLT – hex, 9/16 NF x 1 inch |
| 3 | 425-106 | 1 | NUT, 3/8″-16, G5 |
| 4 | 90-7643T1 | 1 | BRACKET – throttle cable |
| 5 | 60-6425T1 | 1 | CABLE – throttle |
| 6 | 225-14210 | 1 | NUT, #10-32 |
| 7 | H433283 | 1 | JOINT – ball |
| 8 | 163-55 | 1 | SCREW – machine, hex head, No. 10 NC x 1-1/4 inch |
| 9 | 90-7749T1 | 1 | SPACER – joint |
| 10 | 86625057 | 1 | NUT, LOCK, #10-24, GB |
| 11 | 495-31025 | 1 | WASHER – flat, 1/4 x 9/16 x 3/64 inch |
| 12 | 496-21066 | 2 | WASHER – flat, 21/32 x 1-5/16 x 5/32 inch, hardened |
| 1 | 60-7060T3 | 1 | HARNESS – cab main, Includes: Ref. 2 |
| 2 | 60-6128T2 | 1 | RING – coupling, socket |
| 4 | 20-2340T91 | 1 | SWITCH ASSEMBLY – micro, See Figure 6-112 for service parts |
| 5 | 515-23270 | 1 | CLAMP – P-type, 1-1/16 inch ID |
| 6 | 495-11041 | 2 | WASHER – flat, 13/32 x 13/16 x 1/16 inch |
| 7 | 425-104 | 2 | NUT – hex, 1/4 inch NC |
| 9 | 22-823 | 1 | MOUNT – adhesive back, strap |
| 11 | 60-7089T2 | 1 | HARNESS – auxiliary power |
| 12 | 60-6807T1 | 1 | HARNESS – overhead power, for complete overhead wiring system, See Figure 4-10 |
| 14 | 245012C1 | 1 | SWITCH – rocker, 2-speed |
| 16 | 1534229C1 | 1 | SWITCH – parking brake |
| 18 | 426-412 | 1 | BOLT – hex, 1/4 NC x 3/4 inch, grade 8 |
| 19 | 515-23238 | 1 | CLAMP – P-type, 15/16 inch ID |
| 20 | 495-11028 | 1 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 21 | 232-4114 | 2 | NUT, LOCK, 1/4″-20, GC |
| 22 | 492-11025 | 5 | WASHER, LOCK, 1/4″ |
| 23 | 1964773C1 | 1 | LIGHTER – cigar, 12 volt, replaces 245576C1 lighter |
| 26 | 515-23381 | 1 | CLAMP, 1 1/2″, Insul, 3/8″ Bolt, P-type |
| 27 | 413-416 | 1 | BOLT – hex, 1/4 NC x 1 inch |
| 28 | 459-1108 | 2 | SCREW – machine, pan head slotted, No. 10 NF x 1/2 inch |
| 29 | 22-738 | 4 | DIODE – electrical |
| 30 | 60-5052T3 | 1 | PLATE – relay mounting |
| 31 | 193-1000 | 2 | NUT – hex, with external tooth lock washer, No. 10 NF |
| 32 | 495-21031 | 1 | WASHER – flat, 5/16 x 3/4 x 1/16 inch |
| 33 | 60-6853T1 | 1 | BUSHING – protective |
| 34 | 225-14106 | 4 | Nut, #6-32 |
| 1 | 60-7059T3 | 1 | HARNESS – cab main, Includes: Ref. 2 |
| 2 | 60-6128T2 | 2 | RING – coupling, socket |
| 4 | 20-2340T91 | 1 | SWITCH ASSEMBLY – micro, See Figure 6-112 for service parts |
| 5 | 515-23270 | 1 | CLAMP – P-type, 1-1/16 inch ID |
| 6 | 495-11041 | 2 | WASHER – flat, 13/32 x 13/16 x 1/16 inch |
| 7 | 231-1446 | 2 | NUT, LOCK, 3/8″-16, GB |
| 9 | 22-823 | 1 | MOUNT – adhesive back, strap |
| 11 | 60-7089T2 | 1 | HARNESS – auxiliary power |
| 12 | 60-6516T1 | 1 | HARNESS – overhead, cab, for complete overhead wiring system, See Figure 4-10 |
| 13 | 60-6027T1 | 1 | SENSOR – proximity, clutch |
| 17 | 1534229C1 | 1 | SWITCH – parking brake |
| 18 | 426-412 | 1 | BOLT – hex, 1/4 NC x 3/4 inch, grade 8 |
| 19 | 515-23238 | 1 | CLAMP – P-type, 15/16 inch ID, harness |
| 20 | 495-11028 | 1 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 21 | 232-4114 | 2 | NUT, LOCK, 1/4″-20, GC |
| 22 | 60-6059T91 | 1 | SWITCH – mode lever |
| 23 | 1964773C1 | 1 | LIGHTER – cigar, 12 volt, replaces 245576C1 lighter |
| 26 | 515-23381 | 1 | CLAMP, 1 1/2″, Insul, 3/8″ Bolt, P-type, Harness |
| 27 | 413-416 | 1 | BOLT – hex, 1/4 NC x 1 inch |
| 28 | 459-5108 | 2 | SCREW – machine, pan head slotted, No. 10 NF x 1/2 inch |
| 29 | 22-738 | 2 | DIODE – electrical |
| 30 | 60-5052T3 | 1 | PLATE – relay mounting |
| 31 | 193-1000 | 2 | NUT – hex, with external tooth lock washer, No. 10 NF |
| 32 | 495-21031 | 1 | WASHER – flat, 5/16 x 3/4 x 1/16 inch |
| 33 | 60-6853T1 | 1 | BUSHING – rubber |
| 34 | 225-14106 | 4 | Nut, #6-32 |
| 38 | 60-7160T1 | 1 | CONTROLLER – transmission, transmission, prior to P.I.N. JEE0071001 and after |
| 38 | 60-7287T1 | 1 | CONTROLLER – transmission, P.I.N. JEE0071001 and after |
| 1 | 60-7062T1 | 1 | HARNESS – ROPS main, Includes: Ref. 2 |
| 2 | 60-6128T2 | 1 | RING – coupling, socket |
| 3 | 22-674 | 1 | BRACKET – mounting, circuit breaker |
| 4 | 60-6803T1 | 1 | HARNESS – overhead power, ROPS |
| 5 | 515-23381 | 1 | CLAMP, 1 1/2″, Insul, 3/8″ Bolt, P-type |
| 6 | 495-11041 | 1 | WASHER – flat, 13/32 x 13/16 x 1/16 inch |
| 7 | 232-4136 | 1 | NUT, LOCK, 3/8″-16, GC |
| 10 | 459-5108 | 8 | SCREW – machine, pan head slotted, No. 10 NF x 1/2 inch |
| 11 | 245012C1 | 1 | SWITCH – rocker, 2 speed |
| 12 | 193-1000 | 8 | NUT – hex, with external tooth lock washer, No. 10 NF |
| 13 | 20-1451T1 | 1 | BLOCK – junction |
| 14 | 20-2340T91 | 1 | SWITCH ASSEMBLY – micro, See Figure 6-112 for service parts |
| 15 | 495-31022 | 2 | WASHER, #10 |
| 16 | 1964752C1 | 1 | SWITCH – rocker, illumination |
| 17 | 22-823 | 1 | MOUNT – adhesive back, strap |
| 19 | 50-2962T1 | 1 | CONDUIT – 2362 mm (93 inch) long, cut from S119717X bulk conduit, see below |
| 21 | 515-23381 | 1 | CLAMP, 1 1/2″, Insul, 3/8″ Bolt, P-type |
| 22 | 426-412 | 1 | BOLT – hex, 1/4 NC x 3/4 inch, grade 8 |
| 23 | 495-11028 | 1 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 24 | 232-4114 | 2 | NUT, LOCK, 1/4″-20, GC |
| 26 | 60-5052T3 | 1 | PLATE – relay mounting |
| 27 | 22-738 | 2 | DIODE – electrical |
| 30 | 413-416 | 1 | BOLT – hex, 1/4 NC x 1 inch |
| 31 | 230-14106 | 12 | NUT – hex, self-locking, No. 6 NC |
| 32 | 19-5577 | 1 | WASHER – lock, 3/8 inch |
| 33 | 115772 | 1 | NUT – hex, special, 3/8 inch NC |
| 34 | 492-11025 | 1 | WASHER, LOCK, 1/4″ |
| 35 | 425-104 | 1 | NUT – hex, 1/4 inch NC |
| 36 | 60-6853T1 | 1 | BUSHING – rubber |
| 37 | 495-21031 | 1 | WASHER – flat, 5/16 x 3/4 x 1/16 inch |
| 38 | 60-6127T2 | 1 | RING – lock |
| 39 | 1534229C1 | 1 | SWITCH – parking brake |
| 40 | 60-6804T2 | 1 | CABLE – ground, ROPS, if used |
| 1 | 60-7061T2 | 1 | HARNESS – ROPS main, Includes: Ref. 2 |
| 2 | 60-6128T2 | 2 | RING – coupling, socket |
| 3 | 22-674 | 1 | BRACKET – mounting, circuit breaker |
| 4 | 60-6803T1 | 1 | HARNESS – overhead power, ROPS |
| 5 | 515-23381 | 2 | CLAMP, 1 1/2″, Insul, 3/8″ Bolt, P-type, Harness |
| 6 | 495-11041 | 1 | WASHER – flat, 13/32 x 13/16 x 1/16 inch |
| 7 | 232-4136 | 1 | NUT, LOCK, 3/8″-16, GC |
| 9 | 60-6027T1 | 1 | SENSOR – proximity, clutch |
| 10 | 459-5108 | 8 | SCREW – machine, pan head slotted, No. 10 NF x 1/2 inch |
| 11 | 495-31022 | 2 | WASHER, #10 |
| 12 | 193-1000 | 8 | NUT – hex, with external tooth lock washer, No. 10 NF |
| 13 | 20-1451T1 | 1 | BLOCK – junction |
| 14 | 20-2340T91 | 1 | SWITCH ASSEMBLY – micro, clutch, See Figure 6-112 for service parts |
| 16 | 1964752C1 | 1 | SWITCH – rocker, illumination |
| 17 | 22-823 | 1 | MOUNT – adhesive back, strap |
| 19 | 50-2962T1 | 1 | CONDUIT – 2362 mm (93 inch) long, cut from S119717X bulk conduit, see below |
| 20 | 60-6059T91 | 1 | SWITCH – neutral |
| 21 | 515-23238 | 1 | CLAMP – P-type, 15/16 inch ID, harness |
| 22 | 426-412 | 1 | BOLT – hex, 1/4 NC x 3/4 inch, grade 8 |
| 23 | 495-11028 | 1 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 24 | 232-4114 | 2 | NUT, LOCK, 1/4″-20, GC |
| 25 | 60-7287T1 | 1 | CONTROLLER – transmission, P.I.N. JEE0071001 and after |
| 26 | 60-5052T3 | 1 | PLATE – relay mounting |
| 27 | 22-738 | 2 | DIODE – electrical |
| 30 | 413-416 | 1 | BOLT – hex, 1/4 NC x 1 inch |
| 31 | 230-14106 | 12 | NUT – hex, self-locking, No. 6 NC |
| 32 | 19-5577 | 1 | WASHER – lock, 3/8 inch |
| 33 | 115772 | 1 | NUT – hex, special, 3/8 inch NC |
| 34 | 492-11025 | 1 | WASHER, LOCK, 1/4″ |
| 35 | 425-104 | 1 | NUT – hex, 1/4 inch NC |
| 36 | 60-6853T1 | 1 | BUSHING – rubber |
| 37 | 495-21031 | 1 | WASHER – flat, 5/16 x 3/4 x 1/16 inch |
| 38 | 60-6127T2 | 1 | RING – lock |
| 39 | 1534229C1 | 1 | SWITCH – parking brake |
| 40 | 60-6804T2 | 1 | CABLE – ground, ROPS, if used |
| 1 | 60-6516T1 | 1 | HARNESS – overhead, cab |
| 3 | 60-6807T1 | 1 | HARNESS – overhead power, cab |
| 4 | 60-7091T1 | 2 | CABLE – ground, wiper |
| 5 | 83882C91 | 1 | LAMP ASSEMBLY – console illumination |
| 6 | 22-823 | 6 | MOUNT – adhesive back, strap |
| 9 | 22-665T1 | 1 | LAMP ASSEMBLY – warning, parts list Figure 4-48 |
| 10 | ZAA7189850 | 1 | LAMP ASSEMBLY – flood, replaces 20-1730T92 lamp, parts list Figure 4-48 |
| 12 | 19-5577 | 1 | WASHER – lock, 3/8 inch |
| 13 | 115772 | 1 | NUT – hex, special, 3/8 inch NC |
| 17 | 515-23190 | 1 | CLAMP – P-type, 3/4 inch ID |
| 18 | 515-23317 | 1 | CLAMP, 1 1/4″, Insul, 3/8″ Bolt, P-type |
| 19 | 413-416 | 1 | BOLT – hex, 1/4 NC x 1 inch |
| 20 | 193-1000 | 4 | NUT – hex, with external tooth lock washer, No. 10 NF |
| 21 | 459-5108 | 4 | SCREW – machine, pan head slotted, No. 10 NF x 1/2 inch |
| 22 | 60-6523T1 | 1 | HARNESS – rear wiper |
| 24 | 60-6297T1 | 1 | DECAL – circuit breaker |
| 25 | 22-738 | 4 | DIODE – electrical |
| 26 | 60-7064T1 | 1 | DECAL – overhead relay |
| 27 | 1983391C1 | 1 | LAMP – dome, Includes: Ref. 28 |
| 28 | E35556 | 1 | BULB – lamp 12V, 10w |
| 29 | 1983394C2 | 7 | RELAY – mini, 12 volt |
| 30 | 1964752C1 | 1 | SWITCH – rocker, master lamp |
| 31 | 245012C1 | 1 | SWITCH – rocker, dash lamp |
| 32 | 1964751C1 | 1 | SWITCH – rocker, ether start |
| 33 | 1987431C1 | 1 | SWITCH – rocker, rear wiper |
| 34 | 245334C1 | 1 | PLUG – panel switch cover, replaces 60-3210T1 plug |
| 35 | 232-4114 | 1 | NUT, LOCK, 1/4″-20, GC |
| 36 | 20-1451T1 | 1 | BLOCK – junction |
| 37 | 495-21031 | 3 | WASHER – flat, 5/16 x 3/4 x 1/16 inch |
| 38 | 492-11025 | 2 | WASHER, LOCK, 1/4″ |
| 39 | 231-1444 | 3 | NUT, LOCK, 1/4″-20, GB |
| 40 | 60-5748T1 | 2 | SPEAKER – radio |
| 41 | 60-6515T1 | 1 | SWITCH – lamp, door, See Figure 9-68 for mounting hardware |
| 43 | 60-6804T2 | 1 | CABLE – ground, ROPS, overhead door, if used |
| 1 | 20-2483T1 | 1 | HARNESS – overhead |
| 3 | 22-823 | 7 | MOUNT – adhesive back, strap |
| 5 | 22-665T1 | 4 | LAMP ASSEMBLY – warning, parts list Figure 4-48 |
| 6 | ZAA7189850 | 4 | LAMP ASSEMBLY – flood, replaces 20-1730T92 lamp, parts list Figure 4-48 |
| 1 | 22-674 | 1 | BRACKET – mounting, circuit breaker |
| 2 | 22-676 | 2 | CONNECTOR – circuit breaker |
| 4 | 22-809 | 1 | BREAKER – circuit, 5 ampere |
| 5 | 22-670 | 1 | BREAKER – circuit, 10 ampere |
| 6 | 22-671 | 4 | BREAKER – circuit, 15 ampere |
| 7 | 245765C1 | 3 | BREAKER – circuit, 30 ampere |
| 8 | 22-672 | 3 | BREAKER – circuit, 20 ampere |
| 9 | A45686 | 1 | BREAKER – circuit, 40 ampere |
| 10 | 22-674 | 1 | BRACKET – mounting, circuit breaker |
| 11 | 22-676 | 2 | CONNECTOR – circuit breaker |
| 12 | 193-1000 | 9 | NUT – hex, with external tooth lock washer, No. 10 NF |
| 13 | 22-809 | 1 | BREAKER – circuit, 5 ampere |
| 14 | 22-670 | 1 | BREAKER – circuit, 10 ampere |
| 15 | 22-671 | 4 | BREAKER – circuit, 15 ampere |
| 16 | 245765C1 | 2 | BREAKER – circuit, 30 ampere, replaces 22-673 breaker |
| 17 | 22-672 | 1 | BREAKER – circuit, 20 ampere |
| 19 | 20-1451T1 | 1 | BLOCK – junction |
| 21 | 1983394C2 | 8 | RELAY – mini, 12 volt |
| 22 | 425-104 | 3 | NUT – hex, 1/4 inch NC |
| 23 | 492-11025 | 2 | WASHER, LOCK, 1/4″ |
| 24 | 495-21031 | 2 | WASHER – flat, 5/16 x 3/4 x 1/16 inch |
| 25 | 19-5577 | 1 | WASHER – lock, 3/8 inch |
| 26 | 115772 | 1 | NUT – hex, special, 3/8 inch NC |
| 27 | 495-31022 | 2 | WASHER, #10 |
| 1 | 60-5052T3 | 1 | PLATE – relay mounting |
| 2 | 20-1171T1 | 3 | BRACKET – mounting, circuit breaker |
| 3 | 495-21038 | 3 | WASHER – flat, 3/8 x 7/8 x 3/32 inch |
| 4 | 231-1445 | 3 | NUT – hex, self-locking, 5/16 inch NC |
| 9 | 22-809 | 1 | BREAKER – circuit, 5 ampere |
| 10 | 245765C1 | 1 | BREAKER – circuit, 30 ampere |
| 11 | 60-7037T1 | 1 | CABLE – three point hitch |
| 13 | 426-412 | 2 | BOLT – hex, 1/4 NC x 3/4 inch, grade 8 |
| 14 | 492-11025 | 2 | WASHER, LOCK, 1/4″ |
| 16 | 20-1514T1 | 1 | BLOCK – junction |
| 17 | 495-21031 | 2 | WASHER – flat, 5/16 x 3/4 x 1/16 inch |
| 18 | 426-416 | 1 | BOLT – hex, 1/4 NC x 1 inch, grade 8 |
| 19 | 515-23381 | 1 | CLAMP, 1 1/2″, Insul, 3/8″ Bolt, P-type |
| 21 | 19-5773 | 1 | SCREW – machine, Keps head, 1/4 NC x 1-1/4 inch |
| 22 | 60-7158T1 | 1 | DECAL – relay |
| 23 | 22-823 | 1 | MOUNT – adhesive back, strap |
| 26 | 22-677 | 1 | CONNECTOR – circuit breaker |
| 27 | 22-670 | 2 | BREAKER – circuit, 10 ampere |
| 28 | 22-671 | 1 | BREAKER – circuit, 15 ampere |
| 29 | 60-6339T1 | 1 | HARNESS – relay, rear differential lock |
| 30 | 60-6340T1 | 1 | HARNESS – relay, front differential lock |
| 31 | 60-7017T2 | 1 | HARNESS – electronic depth control, prior to P.I.N. JEE0069665, use with Ref. 14, 50-3321T91 valve |
| 31 | 60-7274T1 | 1 | HARNESS – electronic depth control, P.I.N. JEE0069665 and after, use with Ref. 14, 246245A1 valve |
| 32 | 60-6162T1 | 1 | HARNESS – air seat |
| 33 | 60-6303T1 | 1 | WIRE – circuit breaker |
| 35 | 20-2484T1 | 2 | HARNESS – differential, front and rear |
| 36 | 231-1444 | 4 | NUT, LOCK, 1/4″-20, GB |
| 1 | 60-7166T2 | 1 | HARNESS – engine |
| 2 | 492-11010 | 1 | Washer, Lock, #10, Not Shown, Part of solenoid switch kit, with barrier and cover P/N 178149A1 |
| 3 | 20-1676T2 | 1 | SWITCH – temperature, sender, coolant |
| 4 | 183038A1 | 1 | SWITCH – solenoid with cover, starter, Part of solenoid switch kit, with barrier and cover P/N 178149A1 |
| 5 | 60-6251T1 | 1 | DIODE – electrical |
| 6 | 22-824 | 5 | STRAP – tie, 7 inch |
| 7 | 22-738 | 1 | DIODE – electrical |
| 8 | 60-7238T1 | 1 | HARNESS – diode |
| 9 | 60-7237T1 | 1 | WIRE – jumper, starter to switch, replaces 20-2463T2 wire |
| 10 | 140855A2 | 1 | KIT – starter, 12 volt, Delco Remy, parts list Figure 4-40 |
| 11 | 60-6862T1 | 1 | CABLE – ground, engine to starter |
| 12 | 60-6935T1 | 1 | SWITCH – temperature, transmission filter, See Figure 8-034 for correct assembly and component |
| 13 | 237-6008 | 1 | O-Ring, 8-1, 90 Duro, .644″ ID x .087″ Thk |
| 14 | 178148A1 | 1 | COVER – solenoid switch, order 178149A1 kit, below, Part of solenoid switch kit, with barrier and cover |
| 15 | 495-11041 | 1 | WASHER – flat, 13/32 x 13/16 x 1/16 inch |
| 16 | 425-105 | 2 | NUT – hex, 5/16 inch NC, Part of solenoid switch kit, with barrier and cover P/N 178149A1 |
| 17 | L18337 | 2 | STRAP – tie, 15 inch, not shown, Part of solenoid switch kit, with barrier and cover P/N 178149A1 |
| 19 | 426-612 | 1 | BOLT – hex, 3/8 NC x 3/4 inch, grade 8 |
| 23 | 1987560C1 | 1 | ALTERNATOR ASSEMBLY – engine, 125 amp, parts list Figure 4-46 |
| 24 | 358986R1 | 3 | CLAMP – P-type |
| 25 | 231-1445 | 1 | NUT – hex, self-locking, 5/16 inch NC |
| 26 | 60-6860T1 | 1 | CABLE – alternator |
| 28 | 225-14210 | 1 | NUT, #10-32, Not shown, Part of solenoid switch kit, with barrier and cover P/N 178149A1 |
| 29 | 515-2395 | 1 | CLAMP, 3/8″, Insul, 3/8″ Bolt |
| 30 | 1983233C1 | 1 | SWITCH – restriction, air cleaner |
| 31 | 1999755C2 | 1 | COMPRESSOR ASSEMBLY – air conditioning, parts list Figure 9-106 |
| 35 | 495-11028 | 2 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 36 | 492-11025 | 2 | WASHER, LOCK, 1/4″ |
| 37 | 425-104 | 2 | NUT – hex, 1/4 inch NC |
| 38 | 492-11031 | 2 | WASHER, LOCK, 5/16″, Part of solenoid switch kit, with barrier and cover P/N 178149A1 |
| 1 | 60-7171T1 | 1 | HARNESS – transmission, includes clamps |
| 2 | 515-23127 | 1 | CLAMP – P-type, 1/2 inch ID |
| 3 | 60-6089T1 | 1 | HARNESS – dash display |
| 4 | 60-6288T1 | 1 | HARNESS – transmission solenoid |
| 5 | 1-1051 | 1 | GROMMET – protective |
| 6 | 60-6800T1 | 1 | HARNESS – transmission solenoid |
| 7 | 515-2395 | 2 | CLAMP, 3/8″, Insul, 3/8″ Bolt |
| 9 | 60-7204T1 | 1 | SENSOR – magnetic, MPH, replaces 60-6085T1 sensor |
| 13 | 22-823 | 1 | MOUNT – adhesive back, strap |
| 14 | 515-2363 | 1 | CLAMP – P-type, 1/4 inch ID |
| 16 | 426-512 | 3 | BOLT – hex, 5/16 NC x 3/4 inch, grade 8 |
| 17 | 492-11031 | 3 | WASHER, LOCK, 5/16″ |
| 18 | 425-105 | 3 | NUT – hex, 5/16 inch NC |
| 1 | 60-7074T1 | 1 | HARNESS – transmission |
| 3 | 60-7204T1 | 1 | SENSOR – magnetic, MPH, replaces 60-6085T1 sensor |
| 4 | 22-824 | 1 | STRAP – tie, 7 inch |
| 5 | 22-823 | 1 | MOUNT – adhesive back, strap |
| 6 | 515-2395 | 4 | CLAMP, 3/8″, Insul, 3/8″ Bolt |
| 9 | 426-512 | 1 | BOLT – hex, 5/16 NC x 3/4 inch, grade 8 |
| 10 | 492-11031 | 1 | WASHER, LOCK, 5/16″ |
| 11 | 425-105 | 1 | NUT – hex, 5/16 inch NC |
| 12 | 515-2563 | 1 | CLAMP – P-type, 1/4 inch ID |
| 1 | 60-6783T2 | 1 | HARNESS – headlamp, front |
| 2 | 515-2395 | 5 | CLAMP, 3/8″, Insul, 3/8″ Bolt, Tube |
| 3 | 281-14712 | 3 | SCREW – self-tapping, hex washer head, 1/4 NC x 3/4 inch |
| 4 | 425-106 | 3 | NUT, 3/8″-16, G5 |
| 5 | 495-11041 | 3 | WASHER – flat, 13/32 x 13/16 x 1/16 inch |
| 6 | 60-6731T1 | 2 | LAMP – sealed beam, See Figure 4-49 for mounting hardware, replaces 60-6730T92 lamp |
| 1 | 60-7077T2 | 1 | HARNESS – front frame, replaced by Ref. 16, 60-7077T4 harness, when ordering also supply Ref. 31 |
| 2 | 183038A1 | 1 | SWITCH – solenoid with cover |
| 3 | 495-11028 | 2 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 4 | 492-11025 | 2 | WASHER, LOCK, 1/4″ |
| 5 | 425-104 | 2 | NUT – hex, 1/4 inch NC |
| 6 | 492-11031 | 2 | WASHER, LOCK, 5/16″ |
| 7 | 425-105 | 3 | NUT – hex, 5/16 inch NC |
| 8 | 193-1000 | 1 | NUT – hex, with external tooth lock washer, No. 10 NF |
| 9 | 1964538C1 | 1 | SWITCH – temperature, hydraulic, low |
| 12 | 515-23127 | 2 | CLAMP – P-type, 1/2 inch ID |
| 13 | 495-11041 | 2 | WASHER – flat, 13/32 x 13/16 x 1/16 inch |
| 14 | 425-106 | 2 | NUT, 3/8″-16, G5 |
| 15 | 178148A1 | 1 | COVER – solenoid switch |
| 16 | 60-7077T4 | 1 | HARNESS – front frame, replaces Ref. 1, 60-7077T2 harness, when ordering also supply (1) Ref. 32 |
| 17 | 228760A1 | 1 | SENSOR – speed, ground, replaces 1983294C1 sensor |
| 19 | 515-23508 | 1 | CLAMP – P-type, 2 inch ID |
| 20 | 413-612 | 1 | BOLT – hex, 3/8 NC x 3/4 inch |
| 22 | 515-23381 | 1 | CLAMP, 1 1/2″, Insul, 3/8″ Bolt, P-type |
| 24 | 515-23317 | 1 | CLAMP, 1 1/4″, Insul, 3/8″ Bolt, P-type |
| 25 | 31-1070 | 1 | CLAMP – extended P-type |
| 26 | 495-11034 | 1 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 27 | 413-620 | 1 | BOLT – hex, 3/8 NC x 1-1/4 inch |
| 28 | 493-41039 | 1 | WASHER, LOCK, Ext Tooth, 3/8″ |
| 29 | 60-6935T1 | 1 | SWITCH – temperature, high, hydraulic filter, Includes: Ref. 30 |
| 30 | 237-6008 | 1 | O-Ring, 8-1, 90 Duro, .644″ ID x .087″ Thk |
| 31 | 60-7239T1 | 1 | HARNESS – diode, axle lube solenoid |
| 32 | 22-738 | 2 | DIODE – electrical |
| 11 | 237-6006 | 1 | O-Ring, 6-1, 90 Duro, .468″ ID x .078″ Thk |
| 1 | 60-7080T3 | 1 | HARNESS – rear frame |
| 2 | 22-823 | 2 | MOUNT – adhesive back, strap |
| 4 | 31-2242 | 2 | GROMMET – protective |
| 5 | 70-6771T1 | 2 | GUARD – wire, prior to P.I.N. JEE0071001 |
| 5 | 70-6890T2 | 2 | GUARD – wire, P.I.N. JEE0071001 and after |
| 6 | 495-11028 | 4 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 7 | 425-104 | 4 | NUT – hex, 1/4 inch NC |
| 8 | 426-516 | 2 | BOLT – hex, 5/16 NC x 1 inch, grade 8 |
| 9 | 495-11034 | 5 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 10 | 426-428 | 4 | BOLT – hex, 1/4 NC x 1-3/4 inch, grade 8 |
| 11 | A186201 | 2 | HARNESS – includes socket, tail lamp |
| 12 | 121645C1 | 1 | SOCKET – covered, 7 pin |
| 13 | 481849C1 | 1 | BOOT – wiring harness, replaces A169283 boot |
| 16 | 493-41033 | 2 | WASHER – external tooth lock, 5/16 inch |
| 17 | 425-105 | 4 | NUT – hex, 5/16 inch NC |
| 18 | ZAA7189850 | 2 | LAMP ASSEMBLY – field, See Figure 4-48 for mounting hardware, replaces 20-1730T92 lamp |
| 19 | A186202 | 2 | LAMP ASSEMBLY – tail, parts list Figure 4-50 |
| 23 | 493-41033 | 1 | WASHER – external tooth lock, 5/16 inch |
| 24 | 60-6831T91 | 1 | SENSOR – fuel |
| 25 | 515-23190 | 1 | CLAMP – P-type, 3/4 inch ID |
| 26 | 515-23381 | 1 | CLAMP, 1 1/2″, Insul, 3/8″ Bolt, P-type |
| 27 | 463-3108 | 5 | SCREW – machine, hex washer head, No. 10 NC x 1/2 inch |
| 28 | 22-766 | 1 | GROMMET – protective |
| 3 | 280-13410 | 4 | SCREW – self-tapping, hex washer head, No. 8-18 x 5/8 inch |
| 4 | 60-6344T2 | 1 | DECAL – instrument cluster, Power Shift, prior to P.I.N. JEE0071001, not shown |
| 4 | 60-6926T1 | 1 | DECAL – instrument cluster, SynchroShift, prior to P.I.N. JEE0071001, not shown |
| 5 | 60-7285T1 | 1 | DECAL – instrument cluster, Power Shift, P.I.N. JEE0071001 and after, See Figure 9-114 for decal |
| 5 | 60-7286T1 | 1 | DECAL – instrument cluster, SynchroShift, P.I.N. JEE0071001 and after, See Figure 9-114 for decal |
| 13 | 25-9000262 | 2 | SWITCH – instrument cluster |
| 17 | W10478 | 16 | BULB – lamp, No. 194 |
| 18 | 20-1178T1 | 16 | SOCKET – bulb |
| 1 | 60-7056T2 | 1 | COVER – panel, cab, gauge |
| 1 | 60-6166T1 | 1 | COVER – panel, ROPS, gauge, not shown |
| 2 | 19-6136 | 6 | STUD – quarter turn, five used on ROPS |
| 3 | 19-5668 | 6 | WASHER – flat, 1/4 x 3/4 x 3/16 inch, five used on ROPS |
| 4 | A36042 | 6 | RETAINER – quarter turn, five used on ROPS |
| 6 | 425-117 | 1 | NUT – hex, 7/16 inch NF |
| 7 | 230-14106 | 4 | NUT – hex, self-locking, No. 6 NC |
| 8 | 60-5756T1 | 1 | PANEL – gauge |
| 9 | 60-5939T2 | 1 | DECAL – gauge panel, see page 9-117 for decal |
| 10 | 140-101 | 4 | SCREW, Cross Pan Hd, #6-32 x 1/2″ |
| 18 | 20-2018T2 | 1 | GAUGE – hourmeter |
| 19 | 20-2466T1 | 1 | GAUGE – voltmeter |
| 20 | 20-2464T1 | 1 | GAUGE – fuel level |
| 21 | 20-2465T1 | 1 | GAUGE – water temperature, engine |
| 22 | 60-6145T2 | 1 | GAUGE – oil pressure, engine |
| 23 | 23731R1 | 5 | BULB – lamp, No.1893 |
| 24 | 60-6292T4 | 1 | HARNESS – instrument panel lamp |
| 25 | 9411893 | 4 | NUT – hex, self-locking, No. 10 NF |
| 26 | 31-2740 | 1 | ELBOW – 90 degree, 1/8 PT x 7/16 inch thread |
| 27 | 31-2784 | 1 | HOSE – 1067 mm (42 inch) long, gauges |
| 28 | 60-6330T1 | 1 | SWITCH – pressure |
| 29 | 218-1557 | 1 | ADAPTER – straight, 7/16-20 swivel x 1/8 inch female PT |
| 30 | 218-5478 | 1 | TEE – 7/16-20 inch flare branch x flare x swivel |
| 31 | 218-671 | 1 | ADAPTER – straight, 7/16-20 inch flare x bulkhead flare |
| 32 | 64-146 | 1 | PLUG – hole, access |
| 33 | 31-3024 | 1 | HOSE – 2743 mm (108 inch) long, engine oil pressure |
| 34 | 22-824 | 1 | STRAP – tie, 7 inch |
| 35 | 31-1070 | 1 | CLAMP – extended P-type |
| 37 | 515-23190 | 2 | CLAMP – P-type, 3/4 inch ID, one used on cab |
| 38 | 425-106 | 1 | NUT, 3/8″-16, G5 |
| 40 | 218-5228 | 1 | ELBOW – 90 degree, 7/16-20 inch flare x swivel |
| 41 | 218-441 | 1 | ADAPTER – straight, 7/16-20 flare x 1/8 inch PT |
| 1 | 60-7056T2 | 1 | COVER – panel, cab, gauge |
| 1 | 60-6166T1 | 1 | COVER – panel, ROPS, gauge, not shown |
| 2 | 19-6136 | 6 | STUD – quarter turn, five used on ROPS |
| 3 | 19-5668 | 6 | WASHER – flat, 1/4 x 3/4 x 3/16 inch, five used on ROPS |
| 4 | A36042 | 6 | RETAINER – quarter turn, five used on ROPS |
| 6 | 425-117 | 1 | NUT – hex, 7/16 inch NF |
| 7 | 230-14106 | 4 | NUT – hex, self-locking, No. 6 NC |
| 8 | 60-5756T1 | 1 | PANEL – gauge, if used |
| 9 | 60-5939T3 | 1 | DECAL – gauge panel, if used, See Figure 9-116 for decal |
| 10 | 140-101 | 4 | SCREW, Cross Pan Hd, #6-32 x 1/2″ |
| 11 | 60-7295T1 | 1 | PANEL – gauge, if used |
| 12 | 60-7297T1 | 1 | DECAL – gauge panel, if used |
| 13 | 60-7298T1 | 1 | METER – area, if equipped |
| 19 | 20-2466T2 | 1 | GAUGE – voltmeter |
| 20 | 20-2464T2 | 1 | GAUGE – fuel level |
| 21 | 20-2465T2 | 1 | GAUGE – water temperature, engine |
| 22 | 60-6145T2 | 1 | GAUGE – oil pressure, engine |
| 23 | 23731R1 | 5 | BULB – lamp, No.1893 |
| 24 | 60-6292T4 | 1 | HARNESS – instrument panel lamp |
| 25 | 9411893 | 4 | NUT – hex, self-locking, No. 10 NF |
| 26 | 31-2740 | 1 | ELBOW – 90 degree, 1/8 PT x 7/16 inch thread |
| 27 | 31-2784 | 1 | HOSE – 1067 mm (42 inch) long, gauges |
| 28 | 60-6330T1 | 1 | SWITCH – pressure |
| 29 | 218-1557 | 1 | ADAPTER – straight, 7/16-20 swivel x 1/8 inch female PT |
| 30 | 218-5478 | 1 | TEE – 7/16-20 inch flare branch x flare x swivel |
| 31 | 218-671 | 1 | ADAPTER – straight, 7/16-20 inch flare x bulkhead flare |
| 32 | 64-146 | 1 | PLUG – hole, access |
| 33 | 31-3024 | 1 | HOSE – 2743 mm (108 inch) long, engine oil pressure |
| 34 | 22-824 | 1 | STRAP – tie, 7 inch |
| 35 | 31-1070 | 1 | CLAMP – extended P-type |
| 37 | 515-23190 | 2 | CLAMP – P-type, 3/4 inch ID, one used on cab |
| 38 | 425-106 | 1 | NUT, 3/8″-16, G5 |
| 40 | 218-5228 | 1 | ELBOW – 90 degree, 7/16-20 inch flare x swivel |
| 41 | 218-441 | 1 | ADAPTER – straight, 7/16-20 flare x 1/8 inch PT |
| 1 | 20-2458T1 | 1 | HARNESS – cab power |
| 2 | 20-2041T2 | 1 | BREAKER – circuit |
| 3 | 60-1880T1 | 1 | STUD – ground |
| 4 | 425-104 | 4 | NUT – hex, 1/4 inch NC |
| 5 | 492-11025 | 4 | WASHER, LOCK, 1/4″ |
| 6 | 426-612 | 4 | BOLT – hex, 3/8 NC x 3/4 inch, grade 8 |
| 7 | 515-23508 | 1 | CLAMP – P-type, 2 inch ID, retaining |
| 8 | 232-4136 | 5 | NUT, LOCK, 3/8″-16, GC |
| 9 | 231-1446 | 10 | NUT, LOCK, 3/8″-16, GB |
| 13 | BMF31FS | 3 | BATTERY – tractor, 12 volt |
| 14 | 413-624 | 1 | BOLT – hex, 3/8 NC x 1-1/2 inch |
| 17 | 515-23238 | 4 | CLAMP – P-type, 15/16 inch ID, retaining |
| 19 | 20-2459T1 | 2 | CABLE – battery, negative |
| 20 | 20-2094T2 | 2 | CABLE – battery, positive |
| 21 | 60-6790T1 | 1 | CABLE – battery, ground to frame |
| 22 | 20-2457T1 | 1 | CABLE – battery, to starter |
| 23 | 70-5548T1 | 3 | BRACKET – angle |
| 24 | 198185A1 | 6 | BOLT – J-type, battery hold down, replaces 1-1946 and 377837R1 rods |
| 26 | 495-11034 | 6 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 27 | 231-1445 | 9 | NUT – hex, self-locking, 5/16 inch NC |
| 28 | 20-2424T1 | 1 | BOOT – cable end |
| 29 | 107717A1 | 1 | STARTER ASSEMBLY – Delco Remy, 12 volt, engine, parts list Figures 4-38 and 4-40, no longer |
| 30 | 60-6785T1 | 1 | CABLE – starter, ground, starter to frame |
| 31 | 493-41065 | 1 | WASHER – external tooth lock, 5/8 inch |
| 32 | 495-11053 | 1 | WASHER, 1/2″, SAE (17/32″ x 1-1/16″ x 3/32″) |
| 33 | 80679 | 1 | Washer, Lock, 1/2″ |
| 34 | 425-108 | 1 | NUT – hex, 1/2 inch NC |
| 35 | 60-6867T1 | 1 | COVER – cab power supply |
| 36 | 426-412 | 2 | BOLT – hex, 1/4 NC x 3/4 inch, grade 8 |
| 37 | 495-11028 | 2 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 1 | A187561 | 1 | COVER ASSEMBLY – commutator end, Includes: Ref. 2 – 4 |
| 3 | A49769 | 1 | WICK – oil, This part is included in brush kit A187514. |
| 4 | A49573 | 1 | PLUG – oil wick, This part is included in brush kit A187514. |
| 7 | 81772C1 | 1 | ARMATURE – starter, replaces 142943A1 armature |
| 8 | 81771C1 | 1 | COIL – field, replaces 142944A1 coil |
| 9 | A49764 | 1 | WIRE – terminal, commutator end |
| 12 | A49772 | 1 | HOUSING – shift lever, Includes: Ref. 13 – 19 |
| 13 | A49765 | 1 | BUSHING – armature, lever housing, This part is included in brush kit A187514. |
| 15 | A49573 | 1 | PLUG – oil wick, This part is included in brush kit A187514. |
| 16 | 238-5228 | 1 | O-RING, -228, 70 Duro, 2.234″ ID x .139″ Thk, Switch, This part is included in brush kit A187514 and |
| 17 | 238-5243 | 1 | O-RING – 4-1/4 ID x 1/8 inch wide, lever housing, This part is included in brush kit A187514. |
| 18 | R21582 | 1 | SEAL – oil, lever housing, This part is included in brush kit A187514. |
| 19 | A49567 | 1 | WICK – oil, armature bushing, This part is included in brush kit A187514. |
| 22 | 20-1343T1 | 1 | CLUTCH – drive |
| 23 | A49773 | 1 | HOUSING – drive end, Includes: Ref. 24 – 27 |
| 24 | A47257 | 1 | BUSHING – armature, drive housing, This part is included in brush kit A187514. |
| 25 | A47888 | 1 | WICK – oil, This part is included in brush kit A187514. |
| 26 | A47889 | 1 | PLUG – oil wick, This part is included in brush kit A187514. |
| 27 | A43854 | 1 | O-RING – housing, drive housing, This part is included in brush kit A187514 and brush kit A187515. |
| 30 | 141338A1 | 1 | KIT – solenoid, magnetic, with shield |
| 31 | 81769C1 | 1 | PLATE – brush, replaces 142949A1 plate, Includes: Ref. 32 – 36 |
| 32 | 81770C1 | 4 | BRUSH – starter, replaces 142948A1 brush, This part is included in brush kit 142961A1. |
| 33 | A49575 | 4 | SPRING – brush, This part is included in brush kit 142961A1. |
| 34 | A47894 | 4 | SCREW – brush retainer, This part is included in brush kit 142961A1. |
| 36 | 238-5158 | 1 | O-RING, -158, 70 Duro, 4.737″ ID x .103″ Thk, Commutator end, This part is included in brush kit |
| 37 | A49757 | 1 | PLUNGER – solenoid |
| 38 | A49589 | 1 | BOOT – plunger |
| 39 | A41242 | 1 | SPRING – plunger return |
| 40 | A40892 | 1 | WASHER – thrust, flat, 13/16 x 1-3/4 x 3/16 inch, This part is included in brush kit A187514. |
| 41 | 195-2056 | 1 | WASHER – flat, 9/16 x 1 x 1/16 inch, thrust, This part is included in brush kit A187514. |
| 42 | 131-489 | 1 | NUT – hex, self-locking, This part is included in brush kit A187514 and brush kit A187515. |
| 43 | 142952A1 | 6 | BOLT – commutator frame, hex Keps, This part is included in brush kit 142961A1 and brush kit |
| 44 | A41924 | 1 | GASKET – inspection plug, This part is included in brush kit A187514 and brush kit A187515. |
| 50 | A47895 | 1 | WIRE – field coil terminal to solenoid |
| 51 | 80679 | 1 | Washer, Lock, 1/2″ |
| 53 | A47890 | 2 | NUT – flange type, special, 1/2 inch NC |
| 54 | 425-148 | 1 | NUT – hex, jam, 1/2 inch NC |
| 55 | 1546549C1 | 2 | NUT – hex flange, special, No. 10 – 32 NF |
| 59 | 1546551C1 | 6 | SCREW – special, drive housing |
| 60 | A47894 | 2 | SCREW – brush retainer |
| 61 | A187741 | 5 | SCREW – housing retaining |
| 62 | 142955A1 | 8 | SCREW – machine, flat Phillips, 3/8 NF x 21/32 inch |
| 63 | 10497770 | 4 | BOLT – torx head, special, 1/4 NC x 35/64 inch |
| 67 | A41922 | 1 | WASHER – plunger seat |
| 68 | 95-81101 | 1 | WASHER – flat, 33/64 x 7/8 x 1/16 inch |
| 69 | A49779 | 1 | CONNECTOR – field terminal to solenoid |
| 75 | A49767 | 1 | INSULATOR – field coil terminal |
| 76 | A49501 | 1 | INSULATOR – inner, field terminal |
| 77 | A49500 | 1 | INSULATOR – outer, field terminal |
| 78 | A49768 | 1 | KIT – insulator, terminal |
| 83 | A49775 | 1 | LEVER – shift, This part is included in shift lever kit A187515. |
| 89 | A47259 | 1 | O-RING – shaft, shift lever rod, This part is included in shift lever kit A187515. |
| 90 | 238-5012 | 1 | O-RING, -012, 70 Duro, .364″ ID x .070″ Thk, Shift lever rod, This part is included in shift lever kit |
| 91 | A49753 | 1 | PIN – roll, spring |
| 92 | R21587 | 1 | PLUG – inspection, lever housing |
| 93 | R15115 | 4 | SHOE – pole, starter |
| 94 | A43380 | 1 | SEAT – plunger spring |
| 95 | A43419 | 1 | SEAT – spring |
| 98 | A42199 | 1 | SHAFT – shift lever, This part is included in shift lever kit A187515. |
| 99 | 100-1137 | 1 | Ring, Snap, #37, Ext, plunger |
| 100 | 100-1137 | 1 | Ring, Snap, #37, Ext, This part is included in shift lever kit A187515. |
| 101 | L128826 | 1 | GUARD – starter terminal |
| 102 | 1546549C1 | 2 | NUT – hex flange, special, No. 10 – 32 NF |
| 103 | 492-11010 | 1 | Washer, Lock, #10 |
| 1 | 1987560C1 | 1 | ALTERNATOR ASSEMBLY – engine, 125 amp, engine, parts list Figure 4-46 |
| 2 | 90-7610T1 | 1 | MOUNT – alternator |
| 3 | 90-7612T2 | 1 | BRACKET – alternator mount |
| 4 | 90-7613T1 | 1 | PULLEY – alternator |
| 5 | 90-1375T1 | 1 | BELT – alternator, set of two |
| 6 | 426-624 | 3 | BOLT – hex, 3/8 NC x 1-1/2 inch, grade 8 |
| 7 | 426-824 | 1 | BOLT – hex, 1/2 NC x 1-1/2 inch, grade 8, Ref: 7 Per ECN f990689 Bolt changed to longer bolt p/n |
| 8 | 426-8104 | 1 | BOLT – hex, 1/2 NC x 6-1/2 inch, grade 8 |
| 9 | 496-11053 | 3 | WASHER, 17/32″ x 1 1/16″ x .095″, HDN |
| 10 | 231-1448 | 1 | NUT – hex, self-locking, 1/2 inch NC |
| 11 | A49635 | 1 | NUT – shaft |
| 12 | A40792 | 1 | WASHER – flat, 5/8 x 1-1/4 x 3/32 inch |
| 1 | 10467269 | 1 | HOUSING – collector ring end, Includes: Ref. 2, 3 |
| 2 | 1987459C1 | 1 | BEARING – roller |
| 3 | A49631 | 1 | BUSHING – mounting hinge |
| 4 | 1987457C1 | 1 | STATOR – alternator |
| 5 | 1987470C1 | 1 | HOUSING – drive end, Includes: Ref. 6 – 8 |
| 6 | 1987471C1 | 1 | BEARING – ball, drive end |
| 7 | 1987472C1 | 1 | PLATE – retaining, bearing |
| 8 | A48277 | 3 | SCREW – retaining plate, bearing |
| 9 | 1987454C1 | 1 | REGULATOR – alternator |
| 10 | 1987466C1 | 1 | KIT – terminal, battery |
| 11 | 1987467C1 | 1 | KIT – terminal, relay |
| 12 | 1987476C1 | 1 | CONNECTOR – regulator to relay lamp |
| 13 | 1987456C1 | 1 | CONNECTOR – regulator mounting screw to stud |
| 14 | 1987468C1 | 1 | CAPACITOR – alternator |
| 15 | 1987463C1 | 1 | HOLDER ASSEMBLY – brush, Includes: Ref. 16 |
| 16 | 1987464C1 | 2 | BRUSH – holder |
| 17 | 1987461C1 | 1 | RECTIFIER – alternator |
| 18 | 1987455C1 | 1 | ROTOR – alternator |
| 19 | A45537 | 1 | BOOT – voltage adjustment stud |
| 21 | 1987474C1 | 1 | FAN – alternator |
| 23 | A45368 | 1 | NUT – terminal |
| 24 | 225-14108 | 3 | NUT – hex, No. 8 NC |
| 25 | A49635 | 1 | NUT – shaft, drive end |
| 26 | 1987462C1 | 3 | BOLT – hex washer, rectifier bridge retaining |
| 27 | A48257 | 1 | SCREW – brush holder |
| 28 | 1987473C1 | 4 | BOLT – retaining, alternator |
| 29 | A45223 | 2 | SCREW – brush holder, insulated, regulator |
| 30 | 1987469C1 | 1 | SCREW – retaining, capacitor |
| 31 | 1987460C1 | 1 | DIODE – trio |
| 32 | 1987475C1 | 1 | SCREW – hex washer, ground |
| 33 | A40792 | 1 | WASHER – flat, 5/8 x 1-1/4 x 3/32 inch, shaft |
| 35 | 1987552C1 | 1 | SCREEN – debris, alternator |
| 36 | 281-14428 | 1 | SCREW – self-tapping, hex washer head, No. 8 NC x 1-3/4 inch |
| 37 | 281-14728 | 1 | SCREW – self-tapping, hex washer head, 1/4 NC x 1-3/4 inch |
| 40 | 90-7613T1 | 1 | PULLEY – alternator, used on the 9370 and 9380 only |
| 1 | 281-6456 | 2 | SCREW – self-tapping, hex washer head, No. 10 NF x 3/4 inch, front cab grounding |
| 2 | 231-1448 | 4 | NUT – hex, self-locking, 1/2 inch NC |
| 3 | D37049 | 4 | WASHER – lock, 1/2 inch |
| 4 | 60-4336T1 | 2 | BRACKET – mounting, cab to flood lamp, rear cab mount |
| 5 | 413-416 | 4 | BOLT – hex, 1/4 NC x 1 inch |
| 6 | 495-11028 | 4 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 7 | 231-1444 | 4 | NUT, LOCK, 1/4″-20, GB |
| 8 | 87251C1 | 4 | BUSHING – includes wires |
| 9 | 493-21026 | 4 | WASHER – internal tooth lock, 1/4 inch, rear fender grounding |
| 11 | 20-1822T1 | 1 | LENS – sealed beam LAMP ASSEMBLY – FLOOD, REPLACES 20-1730T92 |
| 12 | 425-104 | 2 | NUT – hex, 1/4 inch NC, rear fender grounding LAMP ASSEMBLY – FLOOD, REPLACES 20-1730T92 |
| 20 | A187626 | 1 | LENS – warning lamp ASSEMBLY – FLOOD, REPLACES 20-1730T92 |
| 21 | A41264 | 1 | BULB, #1156, 12V, Lamp, Assembly – Flood, Replaces 20-1730T92 |
| 22 | 19-1104 | 8 | SCREW – machine, pan head cross, No. 8 NC x 1-3/4 inch LAMP ASSEMBLY – FLOOD, REPLACES |
| 2 | 60-6731T1 | 1 | LAMP – sealed beam, replaces 60-6730T92 lamp |
| 3 | 280-16516 | 8 | SCREW – self-tapping, hex washer head, No. 10 – 16 x 1 inch |
| 4 | 60-6843T1 | 8 | BUSHING – brass |
| 5 | 60-7095T1 | 8 | NUT – clip |
| 3 | D71346 | 1 | BULB – lamp, No. 168 |
| 4 | A186201 | 1 | HARNESS – includes socket |
| 5 | 260-14416 | 4 | SCREW – self-tapping, pan Phillips, No. 8-18 x 1 inch |
| 1 | 70-6817T1 | 1 | TUBE – side marker, replaces 70-6723T1 tube |
| 2 | 70-6767T1 | 2 | TUBE – extension, side marker |
| 5 | 495-11028 | 5 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 6 | 231-1444 | 5 | NUT, LOCK, 1/4″-20, GB |
| 7 | 70-6818T1 | 1 | ANGLE – support |
| 8 | 495-11041 | 8 | WASHER – flat, 13/32 x 13/16 x 1/16 inch |
| 9 | 426-620 | 8 | BOLT – hex, 3/8 NC x 1-1/4 inch, grade 8 |
| 10 | 425-106 | 4 | NUT, 3/8″-16, G5 |
| 13 | 60-7038T1 | 1 | HARNESS – side marker |
| 14 | 70-6771T1 | 2 | GUARD – wire |
| 15 | 91913C91 | 2 | LAMP ASSEMBLY – side marker, Includes: Ref. 16 – 20 |
| 17 | A41264 | 1 | BULB, #1156, 12V, Lamp |
| 18 | A43731 | 2 | GASKET – sealing, lens |
| 20 | 187-1083 | 4 | SCREW – self-tapping, round head Phillips, No. 8 NC x 5/8 inch |
| 21 | F63435 | 2 | GASKET – lamp mounting |
| 22 | 493-21026 | 1 | WASHER – internal tooth lock, 1/4 inch |
| 1 | 22-824 | 2 | STRAP – tie, 7 inch |
| 2 | 60-4336T1 | 2 | BRACKET – mounting, cab to flood lamp |
| 3 | D37049 | 2 | WASHER – lock, 1/2 inch |
| 4 | 425-108 | 2 | NUT – hex, 1/2 inch NC |
| 5 | 426-424 | 4 | BOLT – hex, 1/4 NC x 1-1/2 inch, grade 8 |
| 6 | 495-21031 | 8 | WASHER – flat, 5/16 x 3/4 x 1/16 inch |
| 7 | 425-104 | 4 | NUT – hex, 1/4 inch NC |
| 9 | 20-1822T1 | 1 | LENS – sealed beam |
| 10 | 493-11026 | 2 | WASHER – internal-external tooth lock, 1/4 inch |
| 1 | 141950A2 | 1 | RADIO – AM-FM stereo |
| 1 | 141951A2 | 1 | RADIO – AM-FM stereo, with cassette tape player |
| 2 | 60-7157T1 | 1 | BRACKET – mounting |
| 3 | 193-1000 | 1 | NUT – hex, with external tooth lock washer, No. 10 NF |
| 4 | 97080C1 | 1 | ANTENNA ASSEMBLY – radio, includes base, mast, cable, and hardware, replaces 60-6490T1 antenna |
| 5 | 22-766 | 1 | GROMMET – antenna |
| 6 | 60-5748T1 | 2 | SPEAKER – radio |
| 7 | 440-11010 | 8 | SCREW – machine, pan Phillips, No. 10 NC x 5/8 inch |
| 8 | 22-824 | 2 | STRAP – tie, 7 inch |
| 9 | 1987530C1 | 1 | SCREW – flat head, special |
| 2 | 495-11028 | 2 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 3 | 111626C1 | 2 | NUT – hex, self-locking, special, 1/4 inch NC |
| 5 | 60-6528T1 | 1 | BRACKET – wiper mounting spacer |
| 8 | 2-4191T1 | 1 | WASHER – flat |
| 9 | 2-4192T1 | 1 | NUT – hex cap |
| 12 | 414-440 | 2 | BOLT – hex, 1/4 NF x 2-1/2 inch |
| 16 | 2-4194T1 | 1 | BLADE – wiper, rubber, 18 inch |
| 20 | 60-1144T1 | 1 | ARM – wiper, 17 inch |
| 22 | 60-7091T1 | 1 | CABLE – ground, motor |
| 1 | 60-5903T1 | 1 | BRACKET – pivot, left-hand |
| 2 | 60-5904T1 | 1 | BRACKET – pivot, right-hand |
| 3 | 19-5370 | 4 | WASHER – wave, 7/16 x 5/8 x 3/64 inch |
| 4 | 19-6263 | 4 | BEARING – flanged |
| 5 | 19-5866 | 2 | RING – snap, main pivots |
| 6 | 60-6630T1 | 1 | ARM – link, actuating |
| 7 | 19-6262 | 7 | BEARING – snap in |
| 8 | 19-5992 | 4 | RING – snap |
| 9 | 60-5994T1 | 2 | SPACER – ball joint |
| 10 | A146456 | 1 | JOINT – ball, 1/4 inch NF, actuating |
| 11 | 425-114 | 1 | NUT, 1/4″-28, G5 |
| 19 | 111626C1 | 5 | NUT – hex, self-locking, special, 1/4 inch NC |
| 20 | 60-5899T1 | 1 | ANGLE – actuating, front |
| 21 | 60-5900T1 | 1 | ANGLE – actuating, left-hand |
| 22 | 60-5901T1 | 1 | ANGLE – actuating, right-hand |
| 23 | D71414 | 2 | RETAINER – spring clip |
| 24 | 60-6529T2 | 2 | SPACER – shaft, pivot |
| 26 | 2-4190T1 | 2 | GASKET – pivot |
| 27 | 2-4191T1 | 2 | WASHER – flat |
| 28 | 2-4192T1 | 2 | NUT – hex cap |
| 31 | 426-424 | 4 | BOLT – hex, 1/4 NC x 1-1/2 inch, grade 8 |
| 32 | 495-11028 | 4 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 34 | D71417 | 2 | WASHER – special, flat |
| 35 | 495-81032 | 2 | WASHER – flat, 23/32 x 1-1/4 x 3/64 inch |
| 36 | D71419 | 2 | NUT – special, hex jam |
| 37 | D71420 | 2 | CAP – shaft |
| 38 | 1267556C1 | 2 | NUT – knurled drive |
| 39 | 1-9422 | 2 | WASHER – lock |
| 40 | D71422 | 2 | NUT – hex, dome |
| 43 | 463-41012 | 4 | SCREW – machine, hex slotted washer head, No. 10 NC x 3/4 inch |
| 44 | 86632551 | 4 | NUT, LOCK, #10-24, GB |
| 45 | 60-1144T1 | 2 | ARM – wiper, 17 inch |
| 47 | 2-4194T1 | 1 | BLADE – wiper, rubber, 18 inch |
| 2 | 495-11028 | 2 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 3 | 111626C1 | 2 | NUT – hex, self-locking, special, 1/4 inch NC |
| 5 | 60-6529T2 | 1 | SPACER – shaft, pivot |
| 8 | 2-4191T1 | 1 | WASHER – flat |
| 9 | 2-4192T1 | 1 | NUT – hex cap |
| 12 | 414-424 | 2 | BOLT – hex, 1/4 NF x 1-1/2 inch |
| 16 | 2-4194T1 | 1 | BLADE – wiper, rubber, 18 inch |
| 20 | 60-1144T1 | 1 | ARM – wiper, 17 inch |
| 22 | 60-7091T1 | 1 | CABLE – ground, motor |
| 1 | 60-6524T1 | 1 | TANK ASSEMBLY – washer fluid, Includes: Ref. 2 |
| 2 | 60-4241T1 | 1 | CAP – tank |
| 3 | 60-3183T1 | 2 | PUMP – washer fluid |
| 4 | 31-2361 | 1 | CLAMP – P-type, pump |
| 5 | 434-512 | 4 | BOLT – carriage, 5/16 NC x 3/4 inch |
| 6 | 495-11034 | 5 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 7 | 425-105 | 5 | NUT – hex, 5/16 inch NC |
| 20 | 31-2363 | 2 | TEE – nylon, 3/16 inch |
| 21 | 31-2364 | 3 | CONNECTOR – nylon, 3/16 x 7/64 inch |
| 22 | 22-823 | 3 | MOUNT – adhesive back, strap |
| 24 | 60-7077T3 | 1 | HARNESS – front frame |
| 1 | 60-6586T1 | 1 | MOTOR – wiper drive, replaced by 129068A3 kit |
| 2 | 60-6633T1 | 1 | BRACKET – mounting, drive motor |
| 3 | 60-6626T1 | 1 | LEVER – drive |
| 4 | 143267A1 | 1 | NUT – special, retaining, replaces 60-6632T1 nut |
| 5 | 60-6631T1 | 3 | BOLT – special, hex slotted with lockwasher |
| 6 | 60-5913T1 | 1 | SPACER – motor |
| 7 | 19-6265T1 | 1 | SPACER – motor |
| 14 | 2-6870T1 | 1 | SCREW – machine, pan head, special |
| 15 | D71427 | 1 | LINK – connecting |
| 16 | D71414 | 2 | RETAINER – spring clip |
| 19 | 2-6869T91 | 1 | DRIVE ASSEMBLY – shaft and pivot arm, Includes: Ref. 20 – 31 |
| 20 | 493-41026 | 1 | WASHER – external tooth lock, 1/4 inch |
| 21 | 425-114 | 1 | NUT, 1/4″-28, G5 |
| 22 | N6749 | 1 | WASHER – felt |
| 23 | N6750 | 1 | WASHER – flat |
| 24 | 60-3497T1 | 1 | NUT – hex, jam |
| 28 | D71420 | 1 | CAP – shaft, rubber |
| 29 | 1267556C1 | 1 | NUT – knurled drive |
| 30 | 493-21039 | 1 | WASHER – internal tooth lock, 3/8 inch |
| 31 | 60-6635T1 | 1 | NUT – special |
| 40 | A22431 | 3 | WASHER – special, quantity of 1 if equipped with side wiper |
| 1 | 60-6586T1 | 1 | MOTOR – wiper drive, replaced by 129068A3 kit |
| 2 | D72850 | 1 | BRACKET – mounting, replaces 60-6633T1 bracket |
| 3 | 60-6626T1 | 1 | LEVER – drive, Part of wiper motor kit adapter P/N 129068A3. |
| 4 | 143267A1 | 1 | NUT – special, replaces 60-6632T1 nut, Part of wiper motor kit adapter P/N 129068A3. |
| 5 | 60-6631T1 | 3 | BOLT – special, hex slotted with lockwasher |
| 6 | 459-1108 | 2 | SCREW – machine, pan head slotted, No. 10 NF x 1/2 inch |
| 7 | A22431 | 1 | WASHER – special |
| 8 | D71414 | 2 | RETAINER – spring clip |
| 9 | D71427 | 1 | LINK – connecting |
| 10 | 60-6581T91 | 1 | SHAFT ASSEMBLY – wiper drive pivot, Includes: Ref. 11 – 19 |
| 13 | N6749 | 1 | WASHER – felt |
| 14 | N6750 | 1 | WASHER – flat |
| 15 | 60-3497T1 | 1 | NUT – hex, jam |
| 16 | D71420 | 1 | CAP – shaft, rubber |
| 17 | 1267556C1 | 1 | NUT – knurled drive |
| 18 | 493-21039 | 1 | WASHER – internal tooth lock, 3/8 inch |
| 19 | 60-6635T1 | 1 | NUT – special |
| 1 | 20-2484T1 | 2 | HARNESS – differential, front and rear |
| 2 | 60-6341T1 | 1 | HARNESS – switch, differential lock |
| 3 | 60-5052T3 | 1 | PLATE – relay mounting |
| 4 | 60-6340T1 | 1 | HARNESS – relay, front differential lock, See Figure 4-17 for mounting hardware |
| 5 | 60-6066T1 | 2 | SEAL – foam |
| 6 | 60-6065T1 | 2 | ANGLE – retaining, foam |
| 7 | 231-1445 | 4 | NUT – hex, self-locking, 5/16 inch NC |
| 8 | 515-23238 | 3 | CLAMP – P-type, 15/16 inch ID, harness |
| 9 | A62209 | 5 | CLAMP – P-type |
| 10 | 426-624 | 1 | BOLT – hex, 3/8 NC x 1-1/2 inch, grade 8 |
| 11 | 425-106 | 1 | NUT, 3/8″-16, G5 |
| 12 | 60-6339T1 | 1 | HARNESS – relay, rear differential lock, See Figure 4-17 for mounting hardware |
| 13 | 20-1988T1 | 2 | SWITCH – on/off, differential |
| 14 | 426-48 | 4 | BOLT – hex, 1/4 NC x 1/2 inch, grade 8 |
| 15 | 1983394C2 | 2 | RELAY – mini, 12 volt |
| 1 | 463-41012 | 2 | SCREW – machine, hex slotted washer head, No. 10 NC x 3/4 inch |
| 2 | 515-2395 | 2 | CLAMP, 3/8″, Insul, 3/8″ Bolt |
| 4 | 282-44712 | 1 | SCREW – self-drilling tapping, hex washer head, 1/4 NC x 3/4 inch |
| 5 | 60-6290T1 | 1 | HARNESS – horn, replaced by 60-7241T1 harness, Ref. 17 |
| 6 | 193-1004 | 2 | NUT – hex, with external tooth lock washer, No. 10 NC |
| 7 | 1983394C2 | 1 | RELAY – mini, 12 volt |
| 8 | 22-738 | 2 | DIODE – electrical |
| 9 | R45962 | 1 | HORN – “F” Note, 12 volt, electrical, replaced by 60-7242T1 horn, Ref. 15 |
| 10 | 426-512 | 1 | BOLT – hex, 5/16 NC x 3/4 inch, grade 8 |
| 11 | 231-1445 | 1 | NUT – hex, self-locking, 5/16 inch NC |
| 12 | L30866 | 1 | NUT – hex, special |
| 13 | L73799 | 1 | BRACKET – mounting, horn, used with R45962 horn, Ref. 9 |
| 14 | 495-11028 | 2 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 15 | 60-7242T1 | 1 | HORN – 12 volt, replaces R45962 horn, Ref. 9, Includes: Ref. 16 |
| 17 | 60-7241T1 | 1 | HARNESS – horn, replaces 60-6290T1 harness, Ref. 5 |
| 1 | 20-2123T3 | 1 | BOARD ASSEMBLY – circuit, Includes: Ref. 2 |
| 2 | 1983394C2 | 2 | RELAY – mini, 12 volt |
| 4 | 25-1000155 | 1 | BRACKET – mounting, circuit board |
| 5 | 440-10610 | 5 | SCREW – machine, pan Phillips, No. 6 NC x 5/8 inch |
| 6 | 25-1000174 | 5 | SPACER – circuit board |
| 11 | 493-41014 | 5 | Washer, Ext, #6 |
| 12 | 225-14106 | 5 | Nut, #6-32 |
| 16 | 276-1478 | 2 | SCREW – self-tapping, hex head, 1/4 NC x 1/2 inch |
| 1 | 228760A1 | 1 | SENSOR – speed, ground, replaces 1983294C1 sensor |
| 2 | 60-6130T1 | 1 | BRACKET – mounting, sensor |
| 3 | 60-6131T1 | 1 | GUARD – sensor |
| 4 | 426-828 | 2 | BOLT – hex, 1/2 NC x 1-3/4 inch, grade 8 |
| 6 | 231-4118 | 2 | NUT – hex, self-locking, 1/2 inch NC |
| 7 | 426-472 | 4 | BOLT – hex, 1/4 NC x 4-1/2 inch, grade 8 |
| 8 | 425-104 | 4 | NUT – hex, 1/4 inch NC |
| 9 | 495-11028 | 8 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 10 | 22-824 | 1 | STRAP – tie, 7 inch |
| 18 | 492-11025 | 4 | WASHER, LOCK, 1/4″ |
| 20 | 493-21026 | 1 | WASHER – internal tooth lock, 1/4 inch |
| 21 | 50-2955T1 | 4 | SPACER – standoff, mounting |
| 1 | 60-7017T2 | 1 | HARNESS – electronic depth control |
| 2 | 60-7222T1 | 1 | GAUGE – display, seven segment, replaces 60-7015T1 gauge |
| 3 | 60-6120T1 | 1 | PLATE – mounting, controller |
| 4 | 495-11034 | 3 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 5 | 231-1445 | 7 | NUT – hex, self-locking, 5/16 inch NC |
| 6 | 232836A3 | 1 | CONTROLLER – three point hitch, electronic, replaces 60-7014T1 controller |
| 7 | 495-11028 | 2 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 8 | 425-104 | 2 | NUT – hex, 1/4 inch NC |
| 9 | A186061 | 1 | POTENTIOMETER – electrical |
| 11 | 60-7018T1 | 1 | SWITCH – rocker |
| 12 | 1964672C1 | 1 | LIGHT – indicator, amber, 14 volt |
| 14 | 50-3321T91 | 1 | VALVE ASSEMBLY – control, hitch, three point, parts list Figure 8-94 |
| 15 | 163-55 | 2 | SCREW – machine, hex head, No. 10 NC x 1-1/4 inch |
| 16 | 22-823 | 2 | MOUNT – adhesive back, strap |
| 18 | 60-6066T1 | 2 | SEAL – foam |
| 19 | 60-6065T1 | 2 | ANGLE – retaining, foam |
| 20 | 90-7749T1 | 2 | SPACER – joint |
| 21 | 122756A3 | 1 | POTENTIOMETER – single, 1K |
| 22 | 515-23238 | 5 | CLAMP – P-type, 15/16 inch ID, harness |
| 23 | 495-31022 | 2 | WASHER, #10 |
| 24 | 60-7016T2 | 1 | HARNESS – three point hitch |
| 25 | 60-7167T1 | 2 | HARNESS – switch, three point hitch |
| 26 | 60-7039T1 | 2 | SWITCH – toggle, three point hitch |
| 30 | 19-5860 | 1 | Ring, Snap, #75, Ext |
| 31 | 60-6186T1 | 1 | MOUNT – potentiometer |
| 32 | 122756A3 | 1 | POTENTIOMETER – single, 1K, raise and lower |
| 33 | 31-2475 | 1 | GROMMET – wire |
| 34 | 60-6177T1 | 2 | BEARING – ball |
| 35 | 60-6167T3 | 1 | HOUSING – potentiometer |
| 36 | 60-6169T2 | 1 | RETAINER – housing |
| 37 | 495-11028 | 2 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 38 | 493-21026 | 2 | WASHER – internal tooth lock, 1/4 inch |
| 39 | 425-104 | 2 | NUT – hex, 1/4 inch NC |
| 40 | 60-7159T2 | 1 | LEVER – actuating |
| 41 | H433283 | 2 | JOINT – ball, linkage |
| 43 | 86625057 | 2 | NUT, LOCK, #10-24, GB |
| 44 | 225-14210 | 2 | NUT, #10-32 |
| 45 | 60-6175T1 | 1 | ROD – actuating |
| 46 | 60-6185T1 | 1 | PLATE – mounting, housing |
| 47 | 60-6653T1 | 1 | MOUNT – potentiometer assembly |
| 48 | 495-11041 | 2 | WASHER – flat, 13/32 x 13/16 x 1/16 inch |
| 49 | 426-616 | 2 | BOLT, Hex, 3/8″-16 x 1″, G8, Full Thd |
| 1 | 60-7274T1 | 1 | HARNESS – electronic depth control |
| 2 | 60-7222T1 | 1 | GAUGE – display, seven segment |
| 3 | 60-6120T1 | 1 | PLATE – mounting, controller |
| 4 | 495-11034 | 3 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 5 | 231-1445 | 7 | NUT – hex, self-locking, 5/16 inch NC |
| 6 | 60-7281T2 | 1 | CONTROLLER – three point hitch, electronic |
| 7 | 495-11028 | 2 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 8 | 425-104 | 2 | NUT – hex, 1/4 inch NC |
| 9 | A186061 | 1 | POTENTIOMETER – electrical |
| 10 | 425-106 | 2 | NUT, 3/8″-16, G5, P.I.N JEE0069308 and after |
| 11 | 60-7018T1 | 1 | SWITCH – rocker |
| 12 | 1964672C1 | 1 | LIGHT – indicator, amber, 14 volt |
| 14 | 246245A1 | 1 | VALVE ASSEMBLY – control, three point hitch, parts list Figure 8-96 |
| 15 | 163-55 | 2 | SCREW – machine, hex head, No. 10 NC x 1-1/4 inch |
| 16 | 22-823 | 2 | MOUNT – adhesive back, strap |
| 18 | 60-6066T1 | 2 | SEAL – foam |
| 19 | 60-6065T1 | 2 | ANGLE – retaining, foam |
| 20 | 90-7749T1 | 2 | SPACER – joint |
| 21 | 122756A3 | 1 | POTENTIOMETER – single, 1K |
| 23 | 495-31022 | 2 | WASHER, #10 |
| 24 | 60-7016T2 | 1 | HARNESS – three point hitch |
| 25 | 60-7167T1 | 2 | HARNESS – switch, three point hitch |
| 26 | 60-7039T1 | 2 | SWITCH – toggle, three point hitch |
| 30 | 19-5860 | 1 | Ring, Snap, #75, Ext |
| 31 | 60-6186T1 | 1 | MOUNT – potentiometer |
| 32 | 122756A3 | 1 | POTENTIOMETER – single, 1K, raise and lower |
| 33 | 31-2475 | 1 | GROMMET – wire |
| 34 | 60-6177T1 | 2 | BEARING – ball |
| 35 | 60-6167T3 | 1 | HOUSING – potentiometer |
| 36 | 60-6169T2 | 1 | RETAINER – housing |
| 37 | 495-11028 | 2 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 38 | 493-21026 | 2 | WASHER – internal tooth lock, 1/4 inch |
| 39 | 425-106 | 2 | NUT, 3/8″-16, G5 |
| 40 | 60-7159T2 | 1 | LEVER – actuating |
| 41 | H433283 | 2 | JOINT – ball, linkage |
| 43 | 86625057 | 2 | NUT, LOCK, #10-24, GB |
| 44 | 225-14210 | 2 | NUT, #10-32 |
| 45 | 60-6175T1 | 1 | ROD – actuating |
| 46 | 60-6185T1 | 1 | PLATE – mounting, housing |
| 47 | 60-7277T1 | 1 | MOUNT – potentiometer assembly |
| 48 | 495-11041 | 2 | WASHER – flat, 13/32 x 13/16 x 1/16 inch |
| 49 | 426-624 | 2 | BOLT – hex, 3/8 NC x 1-1/2 inch, grade 8 |
| 1 | 60-1827T2 | 1 | WHEEL – steering, no longer available, order 2-3755T92 wheel assembly |
| 2 | 60-1828T1 | 1 | COVER – hub, upper |
| 3 | 60-1829T1 | 1 | COVER – hub, lower |
| 4 | 19-5791 | 2 | SCREW – machine, self-tapping, pan head, No. 6 NS x 1-1/4 inch |
| 5 | 60-1830T1 | 1 | RETAINER – spring |
| 6 | 60-1831T1 | 1 | SPRING – compression, telescoping |
| 10 | 18-1570 | 1 | RING – snap, locking |
| 11 | 60-1951T1 | 1 | LEVER – release, telescoping |
| 12 | 18-1565 | 1 | SCREW – release, telescoping |
| 13 | 60-6469T1 | 2 | SCREW – machine, flat head, No. 10 NF x 1/4 inch |
| 14 | 60-1820T1 | 1 | SPRING – horn button |
| 15 | 19-135 | 1 | STRAP – tie, nylon, not shown |
| 18 | 60-1819T1 | 1 | PLATE – base |
| 19 | 260-14510 | 3 | SCREW – self-tapping, pan Phillips, No. 10-16 x 5/8 inch |
| 20 | 260-14436 | 1 | SCREW – self-tapping, pan Phillips, No. 8-18 x 2-1/4 inch |
| 21 | A13092 | 1 | CUP – contact |
| 22 | 60-1822T1 | 1 | BUTTON – horn |
| 24 | 1-7630 | 1 | COLUMN ASSEMBLY – steering, tilt and telescoping, parts list Figures 5-06 and 5-08 |
| 25 | 425-159 | 1 | NUT – hex, jam, 9/16 inch NF |
| 28 | 18-1567T1 | 1 | LEVER – tilt actuating |
| 29 | 1-4188T1 | 1 | LEVER – turn signal, wiper, washer and hi-low beam |
| 30 | 446363 | 4 | WASHER – flat, 3/8 x 7/8 x 1/16 inch |
| 31 | 614-8016 | 4 | BOLT – hex, full threads, 8 – 1.25 x 16 mm |
| 35 | 32-327 | 1 | GROMMET – column |
| 36 | 60-7109T1 | 1 | SEAL – foam, steering column access |
| 37 | 60-7110T1 | 1 | PLATE – cover, access |
| 38 | 281-14712 | 6 | SCREW – self-tapping, hex washer head, 1/4 NC x 3/4 inch |
| 40 | 60-4436T1 | 1 | FLANGE – coupling, column |
| 41 | 60-4437T1 | 1 | FLANGE – coupling, steering shaft |
| 42 | 7807271 | 2 | BOLT – 12 point, special |
| 43 | 451399 | 1 | NUT – hex, 5/16 inch NF |
| 44 | 9420821 | 1 | NUT – hex, 3/8 inch NF |
| 50 | 22-752T1 | 1 | LOCK ASSEMBLY – ignition, Includes: Ref. 51 |
| 51 | A77313 | 1 | KEY – set of two, not shown |
| 1 | 60-6665T1 | 1 | COLUMN – steering shaft, lower |
| 2 | 426-612 | 4 | BOLT – hex, 3/8 NC x 3/4 inch, grade 8, used with 50-3553T92 valve, prior to P.I.N. JEE0071531 |
| 2 | 627-10020 | 4 | BOLT – hex, full threads, 10 – 1.5 x 20 mm, class 10.9, used with 50-3653T91 valve, P.I.N. |
| 3 | 426-628 | 3 | BOLT – hex, 3/8 NC x 1-3/4 inch, grade 8 |
| 4 | D52276 | 3 | INSULATOR – rubber |
| 5 | 495-21044 | 6 | WASHER – flat, 7/16 x 1 x 5/64 inch |
| 6 | 496-41041 | 3 | WASHER – flat, 13/32 x 1-1/8 x 9/64 inch, hardened |
| 7 | 232-4136 | 3 | NUT, LOCK, 3/8″-16, GC |
| 8 | 60-6664T1 | 1 | SHAFT ASSEMBLY – lower steering, Includes: Ref. 9 & 10 |
| 9 | 60-6177T1 | 1 | BEARING – ball |
| 10 | 19-5860 | 1 | Ring, Snap, #75, Ext |
| 11 | 100-21185 | 1 | Ring, Snap, 1.852″, Int, #185 |
| 1 | 1-1320 | 1 | BUMPER – shaft, retracted steering |
| 2 | 1-1329 | 1 | RETAINER – carrier snap ring |
| 3 | 1-1331 | 1 | RETAINER – shaft lock |
| 4 | 1-1325 | 1 | LOCK – steering shaft |
| 5 | 1-1215 | 1 | CARRIER – lock |
| 6 | 1-4507 | 1 | SPRING – bearing, upper |
| 10 | 1-1333 | 3 | SCREW – machine, binding head |
| 11 | 1-6924 | 1 | SCREW – machine, flanged crown head |
| 12 | 1-4466 | 1 | ARM – signal switch |
| 13 | 1-4497 | 1 | SWITCH – turn signal |
| 14 | 1-1336 | 1 | SEAT – bearing, inner race |
| 16 | 1-4473 | 1 | COVER – lock housing, replaces 2-1454 cover |
| 17 | 1-6926 | 3 | SCREW – machine, oval head |
| 28 | 19-5460 | 1 | BOLT – lock |
| 29 | 1-1227 | 1 | SHOE – lock, steering wheel |
| 30 | 1-1226 | 1 | SHOE – lock, steering wheel |
| 32 | 1-1220 | 1 | PIN – dowel |
| 33 | 1-1301 | 2 | SPRING – shoe |
| 34 | 1-1230 | 1 | SPRING – release lever |
| 35 | 1-1221 | 1 | PIN – release lever |
| 36 | 1-1229 | 1 | SPRING – preload, rack |
| 37 | 1-4476 | 1 | LEVER – shoe release |
| 41 | 1-4494 | 1 | PLATE – retaining, shroud |
| 42 | 19-5459 | 2 | SCREW – machine, oval head |
| 47 | 1-4501 | 1 | LEVER – release, key |
| 48 | 1-4506 | 1 | SPRING – release lever |
| 53 | 1-4508 | 1 | SPRING – wheel tilt |
| 57 | 1-4465 | 1 | ACTUATOR – switch |
| 60 | 1-4488 | 1 | ROD – locking, telescoping |
| 61 | 2-1467 | 1 | SHAFT – steering, upper |
| 62 | 1-1312 | 1 | WEDGE – locking |
| 63 | 1-4487 | 1 | YOKE – race and steering shaft |
| 70 | 1-4486 | 1 | SHAFT – yoke and steering |
| 74 | 1-1326 | 1 | PLATE – lock |
| 75 | 1-4504 | 1 | SHROUD – housing, steering column |
| 76 | 1-1335 | 1 | SCREW – machine, flanged |
| 77 | 1-4496 | 1 | SWITCH – ignition |
| 78 | 1-4468 | 1 | ADAPTER – bearing, lower |
| 79 | 1-4467 | 1 | BEARING – lower |
| 83 | 2-1461 | 1 | JACKET – housing |
| 84 | 1-4498 | 1 | ACTUATOR – rod, dimmer switch |
| 85 | 1-4469 | 1 | COVER – end cap, column housing |
| 86 | 2-1452 | 1 | SWITCH – wiper/washer |
| 87 | 2-1462 | 1 | ROD – dimmer switch |
| 89 | 1-4500 | 1 | KNOB – hazard warning |
| 90 | 19-5456 | 1 | SCREW – machine, oval head |
| 93 | 1-1334 | 4 | SCREW – mounting, support |
| 94 | 2-1455 | 1 | PIN – pivot, switch activating |
| 96 | 1-7739 | 1 | SWITCH – dimmer |
| 97 | 2-1481 | 1 | STUD – mounting, dimmer switch |
| 98 | 225-14110 | 1 | NUT, #10-24 |
| 1 | 50-3553T92 | 1 | VALVE ASSEMBLY – control, steering, prior to P.I.N. JEE0071531, parts list Figure 5-14 |
| 1 | 50-3653T91 | 1 | VALVE ASSEMBLY – steering control, P.I.N. JEE0071531 and after, parts list Figure 5-14 |
| 2 | 218-5063 | 3 | ADAPTER – straight, 7/8-14 flare x 1-1/16-12 inch O-ring boss, Includes: Ref. 3 |
| 3 | 237-6012 | 1 | O-RING, 12-1, 90 Duro, .924 ID x .116″ Thk |
| 4 | 218-1255 | 2 | NUT, LOCK, Blkhd, 3/4″-16 |
| 5 | 31-2958 | 1 | HOSE – 2337 mm (92 inch) long, to left cylinder tee |
| 6 | 31-2959 | 1 | HOSE – 2743 mm (108 inch) long, to cylinder right tee |
| 7 | 218-1236 | 2 | TEE – 3/4-16 inch flare branch x flare x bulkhead flare |
| 10 | 32-150 | 2 | HOSE – 673 mm (26-1/2 inch) long, to tee |
| 11 | 242563A1 | 1 | CLAMP – hose |
| 12 | 425-108 | 1 | NUT – hex, 1/2 inch NC |
| 13 | 80679 | 1 | Washer, Lock, 1/2″ |
| 14 | 31-2961 | 2 | HOSE – 1600 mm (63 inch) long, to tee, replaces 31-2960 hose |
| 18 | 218-5106 | 4 | ELBOW – 90 degree, 3/4-16 inch flare x adj O-ring boss, Includes: Ref. 19 |
| 19 | 237-6008 | 1 | O-Ring, 8-1, 90 Duro, .644″ ID x .087″ Thk |
| 21 | 218-5064 | 2 | ADAPTER – straight, 1-1/16-12 inch flare x O-ring boss, Includes: Ref. 22 |
| 22 | 237-6014 | 1 | O-RING, 14-1, 90 Duro, 1.048″ ID x .116″ Thk |
| 23 | 50-3155T91 | 1 | VALVE ASSEMBLY – priority, parts list Figure 8-38 |
| 24 | 31-3026 | 1 | HOSE – 864 mm (34 inch) long, to filter tube |
| 29 | 31-1041 | 1 | HOSE – 838 mm (33 inch) long, to priority valve |
| 30 | 218-5108 | 1 | ELBOW – 90 degree, 1-1/16-12 inch flare x adj O-ring boss, Includes: Ref. 31 |
| 31 | 237-6012 | 1 | O-RING, 12-1, 90 Duro, .924 ID x .116″ Thk |
| 32 | 218-5039 | 1 | ADAPTER – straight, 1-5/8-12 flare x 1-1/16-12 inch O-ring boss, Includes: Ref. 33 |
| 33 | 237-6020 | 1 | O-RING, 20-1, 90 Duro, 1.475″ ID x .118″ Thk |
| 34 | 50-3504T2 | 1 | TUBE – priority valve to filter |
| 35 | 218-5103 | 1 | ELBOW – 90 degree, 7/16-20 inch flare x adj O-ring boss, Includes: Ref. 36 |
| 36 | 237-6004 | 1 | O-RING, 4-1, 90 Duro, .351″ ID x .072″ Thk |
| 37 | 31-2814 | 1 | HOSE – 711 mm (28 inch) long, control valve |
| 38 | 218-5053 | 1 | ADAPTER – straight, 7/16-20 flare x O-ring boss, Includes: Ref. 39 |
| 39 | 237-6004 | 1 | O-RING, 4-1, 90 Duro, .351″ ID x .072″ Thk |
| 45 | 50-3368T93 | 2 | CYLINDER ASSEMBLY – steering, parts list Figure 5-16 |
| 46 | 50-2037T1 | 1 | STRAP – tie, hose retainer |
| 47 | 19-135 | 4 | STRAP – tie, nylon |
| 3 | S302004 | 7 | BOLT – 12 point, special |
| 4 | S301999 | 1 | PIN – sleeve |
| 5 | S302003 | 1 | CAP – end, steering valve |
| 6 | 50-2990T91 | 1 | GEROTOR – set, matched, replaces S302002 gerotor |
| 7 | 50-2707T1 | 1 | PLATE – spacer, replaces S302001 plate |
| 8 | 50-3604T1 | 1 | RETAINER – spool, front |
| 9 | D82804 | 1 | RACE – thrust, bearing |
| 10 | G13609 | 1 | BEARING – needle |
| 11 | 18-137 | 1 | SEAL – input, input |
| 12 | N13313 | 1 | SEAL – teflon |
| 15 | 50-2703T1 | 1 | RING – backup |
| 16 | 238-5121 | 1 | O-RING, -121, 70 Duro, 1.049″ ID x .103″ Thk |
| 17 | 50-2705T1 | 1 | O-RING – retainer |
| 18 | 50-2708T1 | 3 | O-RING – cover and plate |
| 19 | D77388 | 1 | Ring, Snap, 2.375″, Int, #237 |
| 23 | 50-2706T1 | 1 | SHAFT – drive |
| 24 | D82804 | 1 | RACE – thrust, bearing |
| 25 | W11648 | 4 | BALL – valve |
| 1 | 50-3366T2 | 1 | TUBE – cylinder |
| 2 | 50-3367T1 | 1 | PISTON – cylinder rod |
| 3 | 276-2446 | 3 | SCREW – self-tapping, hex head, No. 8 NC x 3/8 inch |
| 5 | 50-3363T1 | 1 | ROD – piston, cylinder |
| 6 | 50-3361T2 | 1 | GUIDE – piston rod |
| 7 | 19-5582 | 1 | NUT – hex, self-locking, 1-1/4 inch NF |
| 11 | G102287 | 1 | SEAL – piston |
| 12 | S109444 | 1 | RING – backup, piston |
| 13 | G32122 | 1 | RING – backup |
| 14 | 238-5234 | 1 | O-RING, -234, 70 Duro, 2.984″ ID x .139″ Thk |
| 15 | 238-5218 | 1 | O-RING, -218, 70 Duro, 1.234″ ID x .139″ Thk |
| 16 | S109445 | 1 | RING – wear, piston |
| 17 | G107923 | 1 | SEAL – U-cup, piston rod |
| 18 | D95144 | 1 | WIPER – piston rod |
| 1 | 50-3368T93 | 2 | CYLINDER ASSEMBLY – steering, parts list Figure 5-16 |
| 2 | 50-3360T3 | 4 | KNUCKLE – pivot, When replacing Ref. 2, 50-3360T3 knuckle, also order four D95143 wipers, Ref. 22 |
| 3 | 70-6013T2 | 4 | PIN – pivot, knuckle |
| 4 | 70-5967T1 | 8 | SPACER – pin |
| 5 | 426-1024 | 4 | BOLT – hex, 5/8 NC x 1-1/2 inch, grade 8 |
| 6 | 496-21066 | 4 | WASHER – flat, 21/32 x 1-5/16 x 5/32 inch, hardened |
| 7 | 70-6076T2 | 2 | PIN – pivot, cylinder, rear |
| 9 | 219-36 | 2 | FITTING – grease, 45 degree, 1/8 PT x 7/8 inch |
| 10 | 217-430 | 4 | PLUG – hex socket headless, 1/8 inch PT |
| 11 | 70-6085T2 | 2 | PIN – pivot |
| 13 | 426-1024 | 4 | BOLT – hex, 5/8 NC x 1-1/2 inch, grade 8 |
| 14 | 496-21066 | 4 | WASHER – flat, 21/32 x 1-5/16 x 5/32 inch, hardened |
| 18 | 217-1014 | 2 | ELBOW – street, 90 degree, 1/8 inch PT x female PT |
| 19 | 1339090C1 | 2 | HOSE – grease, 838 mm (33 inch) long |
| 20 | F53473 | 2 | NUT – special, hose |
| 21 | 86636814 | 2 | FITTING – grease, straight, 1/4-28 special threads x 1/2 inch |
| 22 | D95143 | 16 | WIPER – dust, When replacing Ref. 2, 50-3360T3 knuckle, also order four D95143 wipers, Ref. 22, per |
| 1 | 70-5981T2 | 1 | MOUNT – transmission, left-hand |
| 2 | 426-1024 | 16 | BOLT – hex, 5/8 NC x 1-1/2 inch, grade 8 |
| 3 | 426-1272 | 6 | BOLT – hex, 3/4 NC x 4-1/2 inch, grade 8 |
| 4 | 47-4171 | 12 | MOUNT – isolator, rubber |
| 5 | 19-5518 | 6 | WASHER – flat, 25/32 x 4 x 3/16 inch |
| 6 | 231-14412 | 6 | NUT – hex, self-locking, 3/4 inch NC |
| 7 | 496-21066 | 4 | WASHER – flat, 21/32 x 1-5/16 x 5/32 inch, hardened |
| 9 | 70-5983T4 | 1 | MOUNT – transmission, right-hand |
| 10 | 90-8454T91 | 1 | TRANSMISSION ASSEMBLY – Powershift, replaces 90-7016T91 transmission, parts list Figures 6-006 |
| 15 | 90-7489T3 | 2 | MOUNT – transmission, lower |
| 16 | 47-4171 | 4 | MOUNT – isolator, rubber |
| 17 | 426-1024 | 4 | BOLT – hex, 5/8 NC x 1-1/2 inch, grade 8 |
| 18 | 496-21066 | 4 | WASHER – flat, 21/32 x 1-5/16 x 5/32 inch, hardened |
| 19 | 426-1272 | 2 | BOLT – hex, 3/4 NC x 4-1/2 inch, grade 8 |
| 20 | 495-11081 | 2 | WASHER, 3/4″, SAE |
| 21 | 19-5518 | 2 | WASHER – flat, 25/32 x 4 x 3/16 inch |
| 22 | 19-85 | 2 | NUT – hex, self-locking, 3/4 inch NC |
| 1 | 70-5981T2 | 1 | MOUNT – transmission, left-hand |
| 2 | 426-1024 | 14 | BOLT – hex, 5/8 NC x 1-1/2 inch, grade 8 |
| 3 | 426-1272 | 6 | BOLT – hex, 3/4 NC x 4-1/2 inch, grade 8 |
| 4 | 47-4171 | 12 | MOUNT – isolator, rubber |
| 5 | 19-5518 | 6 | WASHER – flat, 25/32 x 4 x 3/16 inch |
| 6 | 19-85 | 6 | NUT – hex, self-locking, 3/4 inch NC |
| 7 | 496-21066 | 7 | WASHER – flat, 21/32 x 1-5/16 x 5/32 inch, hardened |
| 9 | 70-5983T4 | 1 | MOUNT – transmission, right-hand |
| 11 | 90-7489T3 | 2 | MOUNT – transmission, lower |
| 12 | 495-11081 | 2 | WASHER, 3/4″, SAE |
| 13 | 426-1028 | 2 | BOLT – hex, 5/8 NC x 1-3/4 inch, grade 8 |
| 1 | S1160S01F | 1 | GASKET – ditch plate, For adapter used on models with PTO, See Figure 6-134, Ref. 5., Part of short |
| 2 | S1170S00F | 1 | PLATE – ditch |
| 3 | 892-11010 | 17 | WASHER – lock, 10 mm |
| 4 | 814-10070 | 3 | BOLT – hex, 10 – 1.5 x 70 mm |
| 5 | S1050S00F | 3 | BOLT – socket head |
| 6 | S1210S00F | 1 | PLUG – hex, O-ring boss, Includes: Ref. 7 |
| 7 | S1200S00F | 1 | O-RING – plug, Part of transmission rebuild gasket kit P/N 33-1559T2. |
| 8 | S1150S02F | 1 | GASKET – regulator valve, Part of short gasket kit P/N 90-8402T91., For adapter used on models with |
| 9 | S7000S01F | 1 | VALVE ASSEMBLY – regulator, parts list Figure 6-028 |
| 10 | 892-11008 | 8 | WASHER, LOCK, M8 |
| 11 | 814-8065 | 8 | BOLT – hex, 8 – 1.25 x 65 mm |
| 12 | S1140S01F | 1 | GASKET – clutch control, Part of short gasket kit P/N 90-8402T91., For adapter used on models with |
| 13 | 90-8201T91 | 1 | VALVE ASSEMBLY – clutch control, parts list Figure 6-026 |
| 14 | SM8124085 | 4 | BOLT – hex, 10 – 1.25 x 85 mm |
| 15 | S1020S00F | 1 | SCREEN – filter |
| 17 | 33-1558T1 | 1 | TUBE – clutch |
| 18 | S1220S01F | 1 | GASKET – range selector valve, Part of short gasket kit P/N 90-8402T91., For adapter used on models |
| 19 | 33-1525T91 | 1 | VALVE ASSEMBLY – range selector, parts list Figure 6-032 |
| 20 | SM8124003 | 10 | BOLT – hex, 10 – 1.25 x 115 mm |
| 25 | 33-1452T1 | 1 | COUPLING – pump |
| 26 | 33-1445T1 | 1 | RING – snap |
| 27 | 33-1516T1 | 1 | ADAPTER – pump drive, models without PTO only, For adapter used on models with PTO, See Figure |
| 28 | 33-1446T1 | 1 | RING – snap |
| 29 | 33-1469T2 | 1 | GASKET – pump, Part of short gasket kit P/N 90-8402T91., For adapter used on models with PTO |
| 30 | 33-1524T91 | 1 | PUMP ASSEMBLY – transmission lubrication, parts list Figure 6-030 |
| 31 | SM8267430 | 2 | STUD – mounting, 14 – 1.5 x 30 mm |
| 32 | SM8911244 | 2 | NUT – hex, 14 mm – 1.5 |
| 33 | 892-11014 | 2 | WASHER – lock, 14 mm |
| 34 | SM8124440 | 2 | BOLT – hex, 14 – 1.5 x 40 mm |
| 35 | S1520S00F | 1 | TUBE – suction |
| 36 | S14701960 | 1 | BALL – steel, tube retaining |
| 37 | S1620S01F | 1 | GASKET – suction tube, Part of short gasket kit P/N 90-8402T91., For adapter used on models with |
| 38 | S1700S00F | 1 | PLATE – suction tube retainer |
| 39 | 218-5110 | 1 | ELBOW – 90 degree, 1-5/16-12 inch flare x adj O-ring boss, Includes: Ref. 40 |
| 40 | 237-6016 | 1 | O-RING – 1-11/64 ID x 7/64 inch wide |
| 16 | 237-6006 | 2 | O-Ring, 6-1, 90 Duro, .468″ ID x .078″ Thk |
| 1 | 33-1470T2 | 1 | GASKET – PTO shaft cover, Part of short gasket kit P/N 90-8402T91. |
| 2 | 33-1442T1 | 1 | COVER – PTO shaft, without PTO |
| 3 | SM8124230 | 10 | BOLT – hex, 12 – 1.25 x 30 mm |
| 4 | 33-1417T2 | 1 | GASKET – bearing retainer, Part of short gasket kit P/N 90-8402T91. |
| 5 | 33-1418T1 | 1 | RETAINER – bearing |
| 6 | 33-1428T1 | 1 | SEAL – output shaft, Part of transmission rebuild gasket kit P/N 33-1559T2. |
| 7 | 33-1420T1 | 1 | YOKE – output, rear |
| 8 | 33-1422T1 | 1 | O-RING – yoke sealing, Part of transmission rebuild gasket kit P/N 33-1559T2. |
| 10 | 33-1432T1 | 1 | PLATE – retainer, yoke |
| 11 | 514-832 | 3 | BOLT – hex, 12 – 1.25 x 35 mm |
| 12 | S1010S00F | 3 | PLUG – O-ring boss, Includes: Ref. 13 |
| 13 | S1080S00F | 1 | O-RING – plug |
| 14 | S1090S00F | 1 | PLUG – magnetic, Includes: Ref. 15 |
| 15 | S1080S00F | 1 | O-RING – plug |
| 1 | 33-1428T1 | 1 | SEAL – output shaft, Part of transmission rebuild gasket kit P/N 33-1559T2. |
| 2 | 33-1422T1 | 1 | O-RING – yoke sealing, Part of transmission rebuild gasket kit P/N 33-1559T2. |
| 4 | 33-1432T1 | 1 | PLATE – retainer, yoke |
| 5 | SM8134235 | 3 | BOLT – hex, 12 mm – 1.25 x 35 mm |
| 7 | 33-1437T1 | 1 | RETAINER – bearing |
| 8 | SM8124050 | 4 | BOLT – hex, 10 – 1.25 x 50 mm |
| 9 | S1610S01F | 1 | GASKET – oil supply plate, Part of short gasket kit P/N 90-8402T91. |
| 10 | S1600S00F | 1 | PLATE – oil supply |
| 11 | 892-11010 | 31 | WASHER – lock, 10 mm |
| 12 | 814-10070 | 7 | BOLT – hex, 10 – 1.5 x 70 mm |
| 13 | 33-1440T2 | 1 | GASKET – oil supply cover, Part of short gasket kit P/N 90-8402T91. |
| 14 | 33-1441T1 | 1 | COVER – oil supply |
| 15 | S1390S00F | 8 | PLUG – O-ring boss, Includes: Ref. 16 |
| 16 | S1320S00F | 8 | O-RING – plug, Part of transmission rebuild gasket kit P/N 33-1559T2. |
| 17 | S1030S00F | 5 | PLUG – hex, O-ring boss, Includes: Ref. 18 |
| 18 | S1040S00F | 5 | O-RING – plug, Part of transmission rebuild gasket kit P/N 33-1559T2. |
| 19 | SM8124060 | 24 | BOLT – hex, 10 – 1.25 x 60 mm |
| 20 | 33-1412T1 | 1 | SEAL – input yoke, Part of transmission rebuild gasket kit P/N 33-1559T2. |
| 21 | 33-1410T1 | 1 | YOKE – input |
| 22 | 33-1414T1 | 1 | O-RING – yoke sealing, Part of transmission rebuild gasket kit P/N 33-1559T2. |
| 24 | 33-1413T1 | 1 | PLATE – yoke retainer |
| 25 | SM8174035 | 3 | BOLT – hex, special, 10 – 1.25 x 35 mm, class 10.9 |
| 26 | 33-1468T2 | 1 | GASKET – pump support, Part of short gasket kit P/N 90-8402T91. |
| 27 | 33-1514T1 | 1 | SUPPORT – oil pump |
| 28 | 33-1444T1 | 1 | COUPLING – pump adapter |
| 29 | 33-1445T1 | 1 | RING – snap |
| 30 | 33-1515T1 | 1 | ADAPTER – pump drive |
| 31 | 33-1517T1 | 1 | RING – snap |
| 33 | 33-1433T2 | 1 | GASKET – clutch collector, Part of short gasket kit P/N 90-8402T91. |
| 34 | 33-1438T1 | 1 | COLLECTOR – clutch |
| 35 | STX99700F | 1 | PLUG – oil |
| 36 | 33-1426T2 | 1 | GASKET – bearing retainer, Part of short gasket kit P/N 90-8402T91. |
| 37 | 33-1427T1 | 1 | RETAINER – bearing |
| 38 | 33-1429T1 | 1 | YOKE – output, front |
| 39 | 33-1439T1 | 2 | PLUG – orifice |
| 1 | 33-1560T1 | 1 | HOUSING – transmission, rear |
| 2 | S2000S02F | 1 | PACK ASSEMBLY – clutch, input, replaces S2000S01A pack, parts list Figure 6-018 |
| 3 | S3000S02F | 1 | PACK ASSEMBLY – clutch, second, replaces S3000S01F pack, parts list Figure 6-020 |
| 4 | S5000S00F | 1 | PACK ASSEMBLY – clutch, 9 inch, parts list Figure 6-024 |
| 5 | S4000S02F | 1 | PACK ASSEMBLY – clutch, 8 inch, parts list Figure 6-022 |
| 7 | 33-1472T1 | 1 | ELBOW – breather tube |
| 8 | 33-1471T1 | 1 | TUBE – breather |
| 9 | 33-1473T1 | 1 | CLAMP – breather tube |
| 10 | 892-11012 | 1 | WASHER, LOCK, M12 |
| 11 | SM8124225 | 1 | BOLT – hex, 12 mm – 1.25 x 25 mm |
| 12 | 33-1455T1 | 1 | ELBOW – 90 degree, breather filter |
| 13 | 33-1454T1 | 1 | FILTER – breather |
| 14 | SAS99900F | 1 | PLUG – retension, filter element |
| 15 | SM8911246 | 1 | NUT – hex, 16 mm – 1.5 |
| 16 | 33-1423T1 | 1 | PIN – roll |
| 17 | 33-1425T1 | 1 | BAFFLE – oil |
| 18 | 33-1424T1 | 2 | STRAP – oil baffle |
| 19 | 895-11012 | 2 | WASHER – flat, 13.5 x 24 x 2.5 mm |
| 20 | 892-11012 | 2 | WASHER, LOCK, M12 |
| 21 | SM8124225 | 2 | BOLT – hex, 12 mm – 1.25 x 25 mm |
| 22 | 825-11410 | 2 | NUT – hex, 10 mm – 1.25 |
| 24 | SM8124020 | 2 | BOLT – hex, 10 – 1.25 x 20 mm |
| 25 | S1400S01F | 1 | HOUSING – transmission, front |
| 26 | 33-1467T1 | 2 | PIN – dowel |
| 27 | SM8121240 | 30 | BOLT – hex, 12 – 1.75 x 40 mm |
| 28 | S1590S01F | 1 | GASKET – oil supply plate, Part of transmission rebuild gasket kit P/N 33-1559T2. |
| 29 | S1580S00F | 1 | PLATE – oil supply |
| 30 | 892-11010 | 7 | WASHER – lock, 10 mm |
| 31 | 514-738 | 7 | BOLT – hex, 10 – 1.25 x 45 mm, replaces SM8124045 bolt |
| 32 | 90-8403T1 | 1 | GUTTER – oil, upper, rear, input gear mesh |
| 33 | 614-6012 | 2 | BOLT, Hex, M6 x 12, 8.8 |
| 23 | 895-11010 | 2 | WASHER – flat, 11 x 20 x 2 mm |
| 1 | 33-1436T1 | 1 | SHAFT – compound |
| 2 | 33-1416T1 | 4 | RING – retaining |
| 3 | 33-1415T3 | 1 | GEAR – compound shaft |
| 4 | 33-1434T1 | 1 | GEAR – drive, 22 teeth |
| 5 | 33-1435T1 | 1 | GEAR – driven, 29 teeth |
| 6 | 90-8459T1 | 2 | CONE – tapered roller bearing, replaces 529207R91 cone and 529208R1 cup |
| 1 | S2900S01F | 1 | SHAFT – drum, also order (4) Ref. 23 S2220S00F washers |
| 2 | S2620S00F | 2 | RING – piston, Part of transmission rebuild gasket kit P/N 33-1559T2. |
| 3 | S2610S00F | 2 | RING – piston |
| 4 | S2630S00F | 2 | RING – sealing, Part of transmission rebuild gasket kit P/N 33-1559T2. |
| 5 | 33-1521T1 | 2 | PISTON – clutch |
| 7 | 33-1518T2 | 10 | PLATE – friction |
| 8 | S2640S00F | 24 | SPRING – return, piston |
| 9 | S2850S00F | 2 | HUB – clutch |
| 10 | S2100S00F | 2 | RING – snap |
| 11 | H144527 | 4 | WASHER – thrust, bearing, 3.2 mm, replaces S2200S00F washer |
| 12 | 572182R1 | 4 | BEARING – needle, thrust, replaces S2230S00F bearing |
| 13 | S2030S00F | 1 | BEARING – roller |
| 14 | S2040S01F | 1 | GEAR – drive, 32 teeth, replaces S2040S00F gear |
| 15 | 90-8459T1 | 2 | CONE – tapered roller bearing, replaces 529208R1 gear and 529207R91 cone |
| 17 | 80909C1 | 1 | BEARING – needle, caged |
| 18 | S2280S00F | 1 | GEAR – drive, 29 teeth |
| 19 | S2240S00F | 1 | RING – retaining |
| 20 | S2270S02F | 1 | GEAR – input, replaces S2270S01F gear |
| 21 | S2410S00F | 1 | CARRIER – piston ring |
| 22 | S2250S00F | 4 | RING – sealing, Part of transmission rebuild gasket kit P/N 33-1559T2. |
| 23 | S2220S00F | 4 | WASHER – thrust, bearing, 2.4 mm |
| 1 | S3900S01F | 1 | SHAFT – drum, also order (4) Ref. 21 S2220S00F washers |
| 2 | S2620S00F | 2 | RING – piston, Part of transmission rebuild gasket kit P/N 33-1559T2. |
| 3 | S2610S00F | 2 | RING – piston, Part of transmission rebuild gasket kit P/N 33-1559T2. |
| 4 | S2630S00F | 2 | RING – sealing, Part of transmission rebuild gasket kit P/N 33-1559T2. |
| 5 | 33-1521T1 | 2 | PISTON – clutch |
| 7 | 33-1518T2 | 10 | PLATE – friction |
| 8 | S2640S00F | 24 | SPRING – return, piston |
| 9 | S2850S00F | 2 | HUB – clutch |
| 10 | S2100S00F | 2 | RING – snap |
| 11 | H144527 | 8 | WASHER – thrust, bearing, 3.2 mm, replaces S2200S00F washer |
| 12 | 572182R1 | 4 | BEARING – needle, thrust, replaces S2230S00F bearing |
| 13 | 80909C1 | 3 | BEARING – needle, caged |
| 14 | S3040S01F | 1 | GEAR – counter, replaces S3040S00F gear |
| 15 | S2280S00F | 1 | GEAR – drive, 29 teeth |
| 16 | S2240S00F | 1 | RING – retaining |
| 17 | S3030S01F | 1 | GEAR – input, 36 teeth |
| 19 | 90-8459T1 | 2 | CONE – tapered roller bearing, replaces 529208R1 cup and 529207R91 cone |
| 20 | S3070S00F | 4 | RING – sealing, Part of transmission rebuild gasket kit P/N 33-1559T2. |
| 21 | S2220S00F | 4 | WASHER – thrust, bearing, 2.4 mm |
| 1 | S4900S02F | 1 | SHAFT ASSEMBLY – drum, Includes: Ref. 2 |
| 2 | S4680S02F | 4 | PIN – guide, 11 mm diameter |
| 3 | S4420S00F | 2 | RING – piston, Part of transmission rebuild gasket kit P/N 33-1559T2. |
| 4 | S4410S00F | 2 | RING – piston, Part of transmission rebuild gasket kit P/N 33-1559T2. |
| 5 | S4430S00F | 2 | RING – sealing, Part of transmission rebuild gasket kit P/N 33-1559T2. |
| 6 | S4180S02F | 2 | PISTON – clutch |
| 8 | 33-1519T2 | 18 | PLATE – faced |
| 9 | S4440S00F | 22 | SPRING – return, piston |
| 10 | S4390S00F | 2 | RING – retaining |
| 11 | S4100S01G | 1 | HUB – clutch |
| 12 | S2100S00F | 2 | RING – snap |
| 13 | S4380S01G | 1 | HUB – clutch |
| 14 | H144527 | 8 | WASHER – thrust, bearing, 3.2 mm, replaces S2200S00F washer |
| 15 | 572182R1 | 4 | BEARING – needle, thrust, replaces S2230S00F bearing |
| 16 | S2210S00F | 1 | BEARING – roller |
| 17 | S4210S00F | 1 | GEAR – output, 38 teeth |
| 18 | S2240S00F | 2 | RING – retaining |