CASE IH 4WD tractor 9370, 9380, 9390
CASE IH 4WD tractor 9370, 9380, 9390 — parts list, part 4 of 4
Assemblies on this page: Parts list (continued) … Parts list (continued).
Parts list (continued)
| Pos | Part no. | Qty | Description |
|---|---|---|---|
| 15 | 627-8012 | 2 | BOLT – hex, full threads, 8 – 1.25 x 12 mm, class 10.9 |
| 16 | 253894A1 | 1 | KNUCKLE – link, right-hand thread |
| 17 | 279051A1 | 1 | LINK ASSEMBLY – U-joint, right-hand thread |
| 20 | 219-8 | 6 | FITTING – grease, straight, 1/4-28 taper x 17/32 inch |
| 1 | 279052A1 | 1 | LINK ASSEMBLY – clevis |
| 4 | 259472A1 | 1 | SPRING – lock |
| 5 | 258552A1 | 1 | LOCK – anti-rotation |
| 6 | 258550A1 | 1 | TURNBUCKLE – linkage |
| 7 | 295004A1 | 4 | PLUG – turnbuckle |
| 10 | 279051A1 | 1 | LINK ASSEMBLY – U-joint, right-hand |
| 11 | 838-3655 | 2 | PIN – roll, 6 x 55 mm |
| 12 | 70-5967T1 | 1 | SPACER – pin |
| 13 | 896-11016 | 1 | WASHER, M17.5 x 30 x 4, HT |
| 14 | 627-16035 | 1 | Bolt, Hex, M16 x 35, 10.9, full threads |
| 15 | 70-6013T2 | 1 | PIN – pivot, knuckle |
| 16 | 253894A1 | 1 | KNUCKLE – link, lift |
| 17 | 219-8 | 4 | FITTING – grease, straight, 1/4-28 taper x 17/32 inch |
| 14 | 895-11008 | 2 | WASHER – flat, 9 x 17 x 1.6 mm |
| 1 | 281462A1 | 1 | HITCH – quick attachment, replaces 70-1919T2 hitch |
| 2 | 70-1895T1 | 1 | PIN – hitch, upper |
| 5 | 70-3082T2 | 3 | BLOCK – pin retaining |
| 6 | 426-816 | 6 | BOLT – hex, 1/2 NC x 1 inch, grade 8 |
| 7 | 70-1894T1 | 2 | PIN – hitch, lower |
| 11 | 70-1880T1 | 2 | HANDLE – hitch release |
| 12 | 70-1884T1 | 2 | LINK – spring return |
| 13 | 2-4345T1 | 2 | SPRING – return, handle |
| 14 | 9416325 | 6 | Pin, 5/16″ x 1 1/8″, Slotted |
| 18 | 70-1887T1 | 2 | LINKAGE – connecting, handle to catch |
| 19 | 70-1890T2 | 2 | CATCH – hitch release |
| 22 | 38-33240 | 4 | Pin, 1/2″ x 2 1/2″, Coiled |
| 23 | 70-1920T1 | 1 | CAP – spacer, right-hand |
| 23 | 70-1921T1 | 1 | CAP – spacer, left-hand |
| 24 | 413-824 | 4 | BOLT – hex, 1/2 NC x 1-1/2 inch |
| 27 | 70-1869T1 | 1 | HOOK – quick attachment |
| 28 | 19-5787 | 4 | BOLT – flange, 3/4 NC x 2-1/2 inch, grade 8 |
| 29 | 131-935 | 4 | NUT – hex flange, 3/4 inch NC |
| 41 | 70-1913T1 | 1 | HOOK – quick attachment, category III conversion kit, 9370 and 9380 only |
| 42 | 326-16120 | 2 | BOLT – hex, 1 NC x 7-1/2 inch, grade 8, category III conversion kit, 9370 and 9380 only |
| 43 | 19-5739 | 4 | WASHER – flat, special, category III conversion kit, 9370 and 9380 only |
| 44 | 425-1016 | 2 | NUT – hex, 1 inch NC, category III conversion kit, 9370 and 9380 only |
| 45 | 2-5306T1 | 2 | SPACER – conversion, category III kit, 9370 and 9380 only |
| 1 | 281462A1 | 1 | HITCH – quick attachment |
| 2 | 70-1895T1 | 1 | PIN – hitch, upper |
| 5 | 70-3082T2 | 3 | BLOCK – pin retaining |
| 6 | 426-816 | 6 | BOLT – hex, 1/2 NC x 1 inch, grade 8 |
| 7 | 70-1894T1 | 2 | PIN – hitch, lower |
| 8 | 2-5306T1 | 2 | SPACER – conversion |
| 11 | 70-1880T1 | 2 | HANDLE – hitch release |
| 12 | 70-1884T1 | 2 | LINK – spring return |
| 13 | 2-4345T1 | 2 | SPRING – return, handle |
| 14 | 38-32018 | 6 | Pin, 5/16″ x 1 1/8″, Coiled |
| 18 | 70-1887T1 | 2 | LINKAGE – connecting, handle to catch |
| 19 | 70-1890T2 | 2 | CATCH – hitch release |
| 22 | 38-33240 | 4 | Pin, 1/2″ x 2 1/2″, Coiled |
| 23 | 70-1920T1 | 1 | CAP – spacer, right-hand |
| 23 | 70-1921T1 | 1 | CAP – spacer, left-hand |
| 24 | 426-824 | 4 | BOLT – hex, 1/2 NC x 1-1/2 inch, grade 8 |
| 27 | 70-1869T1 | 1 | HOOK – quick attachment |
| 28 | 460-1240 | 4 | BOLT – hex flange, 3/4 NC x 2-1/2 inch, grade 8 |
| 29 | 232-41112 | 4 | NUT, LOCK, 3/4″-10, GC |
| 30 | 495-11081 | 4 | WASHER, 3/4″, SAE |
| 41 | 70-1913T1 | 1 | HOOK – quick attachment, category III conversion kit |
| 42 | 426-16120 | 2 | BOLT – hex, 1 NC x 7-1/2 inch, grade 8, category III conversion kit |
| 43 | 326-16120 | 4 | BOLT – hex, 1 NC x 7-1/2 inch, grade 8, category III conversion kit |
| 44 | 425-1016 | 2 | NUT – hex, 1 inch NC, category III conversion kit |
| 1 | 70-6267T1 | 1 | TUBE – receiver, drawbar, prior to P.I.N. JEE0071001 |
| 1 | 70-6898T1 | 1 | TUBE – receiver, drawbar, P.I.N. JEE0071001 and after |
| 2 | 1-4088 | 1 | WASHER – flat, 1-3/4 x 2-3/4 x 1/4 inch |
| 3 | 70-5915T2 | 1 | SPACER – connecting link, P/N 70-5915T2 spacer, replaced in later units Oct. 16, 1998, release |
| 4 | 70-6076T2 | 1 | PIN – drawbar |
| 5 | 70-5967T1 | 1 | SPACER – pin |
| 6 | 496-21066 | 1 | WASHER – flat, 21/32 x 1-5/16 x 5/32 inch, hardened |
| 7 | 426-1024 | 1 | BOLT – hex, 5/8 NC x 1-1/2 inch, grade 8 |
| 8 | 70-4516T1 | 1 | YOKE – cradle, drawbar |
| 9 | 70-4555T1 | 1 | COVER – retaining, slide |
| 10 | 70-4513T2 | 1 | SLIDER – plastic, drawbar |
| 11 | 90-7494T1 | 2 | BOLT – hex, special, 1 NC x 9-1/4 inch |
| 12 | 425-1016 | 2 | NUT – hex, 1 inch NC |
| 13 | 70-1937T2 | 2 | PIN – retaining |
| 14 | 517758R91 | 2 | PIN – klik, locking |
| 16 | 495-21069 | 5 | WASHER – flat, 11/16 x 1-3/4 x 9/64 inch |
| 17 | 426-1020 | 2 | BOLT – hex, 5/8 NC x 1-1/4 inch, grade 8 |
| 18 | 70-1731T1 | 1 | PIN – drawbar retaining |
| 19 | 19-1041 | 1 | PIN – klik, locking |
| 20 | 70-1735T1 | 1 | PIN – drawbar pull |
| 26 | 70-6913T1 | 1 | DRAWBAR – extendable, hardened, P/N 70-6913T1 is a heat-treated drawbar. See NTR SB 017 98 |
| 27 | 70-6263T2 | 2 | PLATE – spacer block |
| 28 | 70-6265T1 | 1 | PLATE – hammerstrap |
| 29 | 70-6249T1 | 1 | LATCH – mount |
| 31 | 90-7494T1 | 2 | BOLT – hex, special, 1 NC x 9-1/4 inch |
| 32 | 425-1016 | 2 | NUT – hex, 1 inch NC |
| 33 | 1965315C2 | 1 | LEVER – hammerstrap |
| 34 | 527-204 | 1 | PIN – clevis, 10 x 43 mm |
| 35 | 432-816 | 1 | 1/8″ x 1″ |
| 36 | 70-6264T2 | 2 | BLOCK – spacer, 1-1/2 inch thick |
| 40 | 70-4620T2 | 1 | BUSHING – drawbar |
| 41 | 70-6099T3 | 1 | HANGER – drawbar, prior to P.I.N. JEE0071001, not shown, If ordering 70-6099T3 hanger, prior to |
| 42 | 426-1648 | 10 | BOLT – hex, 1 NC x 3 inch, grade 8 |
| 43 | 19-5739 | 20 | WASHER – flat, special |
| 44 | 425-1016 | 10 | NUT – hex, 1 inch NC |
| 45 | 426-1640 | 4 | BOLT – hex, 1 NC x 2-1/2 inch, grade 8, use with 223274A1 hanger, Ref. 48 |
| 46 | 496-21106 | 20 | WASHER – flat, 1-1/16 x 2 x 13/64 inch, hardened, use with 223274A1 hanger, Ref. 48 |
| 47 | 429-1016 | 10 | NUT – hex, 1 inch NC, grade 8, use with 223274A1 hanger, Ref. 48 |
| 48 | 223274A1 | 1 | HANGER – drawbar, P.I.N. JEE0071001 and after, If ordering 70-6099T3 hanger, prior to P.I.N. |
| 1 | 336135A1 | 1 | HANGER – drawbar |
| 2 | 336136A1 | 1 | DRAWBAR – Reynolds |
| 7 | 326-24144 | 1 | BOLT – hex |
| 8 | 495-11162 | 1 | WASHER – flat, 1-5/8 x 3 x 5/32 inch |
| 9 | 329-1024 | 1 | NUT, 1 1/2″-6, G8 |
| 10 | 413-16112 | 2 | BOLT – hex, 1 NC x 7 inch, Per ECN F98936 correct bolt is 426-16112 it is a HEX HD 1.00 x 7.00 |
| 11 | 429-1016 | 12 | NUT – hex, 1 inch NC, grade 8 |
| 12 | 496-21106 | 22 | WASHER – flat, 1-1/16 x 2 x 13/64 inch, hardened |
| 13 | 426-1648 | 10 | BOLT – hex, 1 NC x 3 inch, grade 8 |
| 14 | 70-6013T2 | 1 | PIN – pivot, knuckle |
| 15 | 70-5967T1 | 1 | SPACER – pin |
| 16 | 496-21066 | 1 | WASHER – flat, 21/32 x 1-5/16 x 5/32 inch, hardened |
| 17 | 426-1024 | 1 | BOLT – hex, 5/8 NC x 1-1/2 inch, grade 8 |
| 1 | 305091A1 | 1 | FRAME – front, replaces 70-6641T1 frame |
| 3 | 70-6209T2 | 1 | DOOR – component cover |
| 4 | 70-6210T2 | 2 | HINGE – door, mounting |
| 5 | 70-6200T1 | 2 | HINGE – door |
| 6 | 70-1996T3 | 2 | PIN – hinge |
| 7 | 70-2600T2 | 4 | RING – retaining |
| 8 | 70-6207T2 | 1 | BRACKET – mounting |
| 9 | 426-612 | 4 | BOLT – hex, 3/8 NC x 3/4 inch, grade 8 |
| 10 | 495-21044 | 12 | WASHER – flat, 7/16 x 1 x 5/64 inch |
| 11 | 232-4136 | 16 | NUT, LOCK, 3/8″-16, GC |
| 12 | 19-5709 | 3 | WASHER – special, Ref #12 – used to take up spagce in the bushing. MU. TSG. 10/28/99 |
| 13 | 231-1446 | 12 | NUT, LOCK, 3/8″-16, GB |
| 14 | 426-616 | 8 | BOLT, Hex, 3/8″-16 x 1″, G8, Full Thd |
| 15 | 70-6206T1 | 1 | LATCH – access door |
| 16 | 496-81023 | 1 | WASHER – flat, 13/32 x 3/4 x 7/32 inch, hardened, latch |
| 17 | 90-7524T1 | 1 | SPRING – latch |
| 18 | 90-6966T1 | 1 | HANDLE – door latch |
| 19 | 70-1996T3 | 1 | PIN – retaining |
| 20 | 9415236 | 1 | PIN – 1/8 x 3/4 inch, spring |
| 21 | 70-6213T1 | 1 | ROD – retainer, replaced by 70-6336T1 rod, Ref. 22 |
| 22 | 70-6336T1 | 1 | ROD – retainer, replaces 70-6213T1 rod, Ref. 21 |
| 25 | 60-6607T2 | 1 | SEAL – foam, 711 mm (28 inch) long, cut from 60-4596T1 bulk seal, see below |
| 26 | 70-5107T1 | 1 | STEP – rear, bottom |
| 27 | 70-5109T1 | 1 | STRAP – stabilizer, step |
| 28 | 426-616 | 8 | BOLT, Hex, 3/8″-16 x 1″, G8, Full Thd |
| 29 | 231-1446 | 12 | NUT, LOCK, 3/8″-16, GB |
| 30 | 70-2142T3 | 1 | STEP – lower front |
| 33 | 495-21056 | 2 | WASHER – flat, 9/16 x 1-3/8 x 7/64 inch |
| 34 | 425-108 | 2 | NUT – hex, 1/2 inch NC |
| 35 | 426-824 | 2 | BOLT – hex, 1/2 NC x 1-1/2 inch, grade 8 |
| 45 | 1-6835 | 4 | STRIP – anti-skid, 406 mm (16 inch) long, cut from 26-211 bulk strip, see below |
| 1 | 70-6480T1 | 1 | LINK – center, articulation and oscillation |
| 2 | 70-5468T1 | 1 | BEARING – spherical |
| 3 | 70-6217T1 | 1 | BUSHING – pivot, link |
| 4 | 101-21354 | 1 | RING – internal retaining, No. 354 |
| 9 | 70-6076T2 | 2 | PIN – pivot |
| 10 | 70-5967T1 | 1 | SPACER – pin |
| 11 | 426-1024 | 1 | BOLT – hex, 5/8 NC x 1-1/2 inch, grade 8 |
| 12 | 496-21066 | 1 | WASHER – flat, 21/32 x 1-5/16 x 5/32 inch, hardened |
| 13 | 425-1010 | 1 | NUT, 5/8″-11, G5 |
| 14 | 219-55 | 1 | FITTING – grease, 90 degree, 1/8 PT x 27/32 inch |
| 16 | D95143 | 2 | WIPER – piston rod |
| 17 | 219-1 | 17 | FITTING – grease, straight, 1/8 PT x 21/32 inch |
| 19 | 70-5967T1 | 1 | SPACER – pin |
| 20 | 426-1024 | 1 | BOLT – hex, 5/8 NC x 1-1/2 inch, grade 8 |
| 21 | 496-21066 | 1 | WASHER – flat, 21/32 x 1-5/16 x 5/32 inch, hardened |
| 22 | 426-612 | 4 | BOLT – hex, 3/8 NC x 3/4 inch, grade 8 |
| 23 | 495-11041 | 4 | WASHER – flat, 13/32 x 13/16 x 1/16 inch |
| 25 | 70-6477T2 | 1 | COVER – driveshaft, right-hand |
| 26 | 70-6478T2 | 1 | COVER – driveshaft, left-hand |
| 27 | 426-812 | 4 | BOLT – hex, 1/2 NC x 3/4 inch, grade 8 |
| 28 | 495-11053 | 4 | WASHER, 1/2″, SAE (17/32″ x 1-1/16″ x 3/32″) |
| 30 | 70-6216T2 | 1 | STEP – maintenance |
| 1 | 70-6650T1 | 1 | FRAME – rear |
| 2 | R37021 | 1 | BEARING – pivot, spherical, prior to P.I.N. JEE0071001 |
| 2 | 70-6110T1 | 1 | BEARING – pivot, spherical, P.I.N. JEE0071001 and after |
| 3 | 70-6063T1 | 2 | RETAINER – bearing, Ref #3 and #4 – If there is a gap between items number 3 and 4 a washer |
| 4 | 70-5836T2 | 2 | SLEEVE – bearing |
| 5 | 70-4621T2 | 2 | BUSHING – frame, rear |
| 6 | 495-21031 | 4 | WASHER – flat, 5/16 x 3/4 x 1/16 inch |
| 7 | 426-620 | 16 | BOLT – hex, 3/8 NC x 1-1/4 inch, grade 8 |
| 8 | 426-48 | 4 | BOLT – hex, 1/4 NC x 1/2 inch, grade 8 |
| 9 | 219-36 | 1 | FITTING – grease, 45 degree, 1/8 PT x 7/8 inch, prior to P.I.N. JEE0071001 |
| 9 | 219-55 | 1 | FITTING – grease, 90 degree, 1/8 PT x 27/32 inch, P.I.N. JEE0071001 and after |
| 10 | A162191 | 1 | CAP – fuel, prior to P.I.N. JEE0071001 |
| 10 | 2-3679T1 | 1 | CAP – fuel, P.I.N. JEE0071001 and after |
| 11 | 70-6709T1 | 1 | BRACKET – lamp mounting, left-hand |
| 11 | 70-6707T1 | 1 | BRACKET – lamp mounting, right-hand, not shown |
| 12 | 70-6199T1 | 16 | SPACER – cover |
| 13 | 217-430 | 2 | PLUG – hex socket headless, 1/8 inch PT |
| 14 | 163-47 | 8 | SCREW – machine, hex head, No. 10 NC x 1/2 inch |
| 15 | D95148 | 2 | WIPER – seal |
| 16 | 70-6378T3 | 2 | SEAL – outer |
| 17 | 70-6198T1 | 2 | RETAINER – gasket |
| 18 | 70-6189T1 | 2 | COVER – bearing |
| 19 | 70-6190T1 | 2 | HOUSING – bearing |
| 20 | 70-6180T3 | 1 | PIN – pivot, frame |
| 21 | 70-5967T1 | 1 | SPACER – pin |
| 22 | 426-1024 | 1 | BOLT – hex, 5/8 NC x 1-1/2 inch, grade 8 |
| 23 | 495-11066 | 1 | WASHER – flat, 21/32 x 1-5/16 x 3/32 inch |
| 24 | 1-4088 | 1 | WASHER – flat, 1-3/4 x 2-3/4 x 1/4 inch |
| 25 | 70-6221T1 | 1 | NUT – special locking |
| 26 | 70-5891T2 | 1 | PLATE – SMV |
| 27 | 70-6774T1 | 1 | BRACKET – mounting, electrical plug |
| 28 | 426-516 | 2 | BOLT – hex, 5/16 NC x 1 inch, grade 8 |
| 29 | 495-11034 | 4 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 1 | 70-6601T1 | 1 | HOOD – engine |
| 2 | 70-6730T1 | 1 | LATCH – open hood retaining |
| 3 | 70-5269T1 | 2 | FERRULE – wire rope |
| 4 | 70-6732T1 | 1 | ROPE – wire, 4521 mm (178 inch) long, cut from 70-5252T1 bulk rope, see below |
| 5 | 70-6308T1 | 1 | LATCH – hood |
| 6 | 19-6154 | 1 | WASHER – flat, nylon, 3/8 x 1-1/4 x 1/16 inch |
| 7 | 495-11041 | 1 | WASHER – flat, 13/32 x 13/16 x 1/16 inch |
| 8 | 427-6156 | 1 | PIN – clevis, 3/8 x 1-9/16 inch, hardened |
| 9 | 60-6422T1 | 1 | SPRING – compression |
| 10 | 32-612 | 1 | PIN, SPLIT (COTTER), 3/32″ x 3/4″ |
| 11 | 38-11216 | 1 | PIN, 3/16″ x 1″, Slotted |
| 13 | 70-5263T1 | 5 | SEAL – foam, 1092 mm (43 inch) long, cut from 70-5259T1X bulk seal, see below |
| 16 | 70-4262T2 | 2 | PIN – hood hinge |
| 17 | 9415236 | 4 | PIN – 1/8 x 3/4 inch |
| 18 | 70-4263T1 | 2 | HINGE – hood |
| 19 | 426-620 | 8 | BOLT – hex, 3/8 NC x 1-1/4 inch, grade 8 |
| 20 | 496-41041 | 6 | WASHER – flat, 13/32 x 1-1/8 x 9/64 inch, hardened |
| 22 | 19-6261 | 2 | SPRING – assist, hood opening |
| 23 | 426-836 | 2 | BOLT – hex, 1/2 NC x 2-1/4 inch, grade 8 |
| 24 | 2-8012T1 | 2 | SPACER – spring retainer |
| 25 | 19-961 | 2 | WASHER – flat |
| 28 | 425-106 | 1 | NUT, 3/8″-16, G5 |
| 29 | 70-6753T1 | 1 | MOUNT – latch |
| 30 | 70-6178T1 | 1 | LATCH – release |
| 31 | A163012 | 1 | SPRING – latch return |
| 32 | 60-6705T1 | 1 | SEAL – foam, rear hood |
| 35 | 70-6501T2 | 1 | SUPPORT – hood |
| 36 | 426-820 | 4 | BOLT – hex, 1/2 NC x 1-1/4 inch, grade 8 |
| 37 | 495-21056 | 11 | WASHER – flat, 9/16 x 1-3/8 x 7/64 inch |
| 38 | 231-4118 | 4 | NUT – hex, self-locking, 1/2 inch NC |
| 39 | 70-6755T1 | 1 | BRACKET – hood retaining latch |
| 40 | 426-616 | 4 | BOLT, Hex, 3/8″-16 x 1″, G8, Full Thd |
| 41 | 495-21044 | 5 | WASHER – flat, 7/16 x 1 x 5/64 inch |
| 42 | 231-1446 | 3 | NUT, LOCK, 3/8″-16, GB |
| 43 | N7673 | 2 | BUMPER – rubber |
| 44 | 425-105 | 4 | NUT – hex, 5/16 inch NC |
| 1 | 324564A1 | 1 | HOOD – engine, also order (1) 313066A1 plate Ref. 29 and (1) 324785A1 pin Ref. 39, replaces |
| 2 | 70-6840T1 | 1 | LATCH – open hood retaining |
| 3 | 70-5275T1 | 3 | CLAMP – includes U-bolt and nut, Part of hood latch kit P/N 35-1983T91. |
| 4 | 70-6732T1 | 1 | ROPE – wire, 4521 mm (178 inch) long, cut from 70-5252T1 bulk rope, see below |
| 12 | 426-610 | 1 | BOLT – hex, 3/8 NC x 5/8 inch, grade 8 |
| 13 | 70-5263T1 | 5 | SEAL – foam, 1092 mm (43 inch) long, cut from 70-5259T1X bulk seal, see below |
| 16 | 70-4262T2 | 2 | PIN – hood hinge |
| 17 | 9415236 | 4 | PIN – 1/8 x 3/4 inch |
| 18 | 70-4263T1 | 2 | HINGE – hood |
| 19 | 426-620 | 7 | BOLT – hex, 3/8 NC x 1-1/4 inch, grade 8 |
| 20 | 496-41041 | 9 | WASHER – flat, 13/32 x 1-1/8 x 9/64 inch, hardened |
| 22 | 19-6261 | 2 | SPRING – assist, hood opening |
| 23 | 426-836 | 2 | BOLT – hex, 1/2 NC x 2-1/4 inch, grade 8 |
| 24 | 2-8012T1 | 2 | SPACER – spring retainer |
| 25 | 19-961 | 2 | WASHER – flat |
| 28 | 426-524 | 3 | BOLT – hex, 5/16 NC x 1-1/2 inch, grade 8, Part of hood latch kit P/N 35-1983T91. |
| 29 | 313066A1 | 1 | MOUNT – latch, replaces 70-6822T1 mount, also order (1) 324785A1 striker Ref. 39 |
| 30 | 60-5001T1 | 1 | LATCH – door, Part of hood latch kit P/N 35-1983T91. |
| 31 | A163012 | 1 | SPRING – latch return |
| 32 | 60-6705T1 | 1 | SEAL – foam, rear hood |
| 33 | 70-6841T1 | 1 | ARM – latch articulation, Part of hood latch kit P/N 35-1983T91. |
| 34 | 426-512 | 2 | BOLT – hex, 5/16 NC x 3/4 inch, grade 8, Part of hood latch kit P/N 35-1983T91. |
| 35 | 70-6501T2 | 1 | SUPPORT – hood, prior to P.I.N. JEE0071837 |
| 36 | 426-824 | 4 | BOLT – hex, 1/2 NC x 1-1/2 inch, grade 8 |
| 37 | 495-21056 | 10 | WASHER – flat, 9/16 x 1-3/8 x 7/64 inch |
| 38 | 231-4118 | 5 | NUT – hex, self-locking, 1/2 inch NC |
| 39 | 324785A1 | 1 | STRIKER – hood retaining latch, also order (1) 313066A1 mount Ref. 29, replaces 70-6823T1 striker |
| 40 | 426-616 | 3 | BOLT, Hex, 3/8″-16 x 1″, G8, Full Thd |
| 41 | 495-21044 | 5 | WASHER – flat, 7/16 x 1 x 5/64 inch |
| 42 | 231-1446 | 3 | NUT, LOCK, 3/8″-16, GB |
| 43 | N7673 | 2 | BUMPER – rubber |
| 44 | 425-105 | 9 | NUT – hex, 5/16 inch NC |
| 45 | 492-11038 | 2 | WASHER, LOCK, 3/8″, Part of hood latch kit P/N 35-1983T91. |
| 46 | 231-1444 | 1 | NUT, LOCK, 1/4″-20, GB, Part of hood latch kit P/N 35-1983T91. |
| 47 | 426-412 | 1 | BOLT – hex, 1/4 NC x 3/4 inch, grade 8, Part of hood latch kit P/N 35-1983T91. |
| 48 | 70-6829T1 | 1 | PLATE – guide, Part of hood latch kit P/N 35-1983T91. |
| 49 | 70-6923T1 | 1 | SUPPORT – hood, P.I.N. JEE0071837 and after, Part of hood latch kit P/N 35-1983T91. |
| 2 | 70-6727T1 | 2 | BRACKET – lamp mounting |
| 3 | 70-2507T2 | 3 | PLATE – bracket mounting |
| 4 | 151-515 | 18 | RIVET – break mandrel, 5/32 x 7/16 inch |
| 5 | 19-6113 | 1 | BUSHING – nylon, split, flanged |
| 6 | 70-1996T3 | 2 | PIN – hinge |
| 7 | 70-2600T2 | 4 | RING – retaining |
| 8 | 426-616 | 1 | BOLT, Hex, 3/8″-16 x 1″, G8, Full Thd |
| 9 | 426-412 | 1 | BOLT – hex, 1/4 NC x 3/4 inch, grade 8 |
| 10 | 70-6600T1 | 1 | LATCH – grille |
| 11 | 426-612 | 1 | BOLT – hex, 3/8 NC x 3/4 inch, grade 8 |
| 12 | 425-106 | 1 | NUT, 3/8″-16, G5 |
| 13 | 70-5814T1 | 1 | BUSHING – grille latch |
| 14 | 495-21056 | 2 | WASHER – flat, 9/16 x 1-3/8 x 7/64 inch |
| 15 | 231-4118 | 1 | NUT – hex, self-locking, 1/2 inch NC |
| 16 | 70-2806T1 | 1 | SPACER – grille latch |
| 17 | 425-146 | 1 | NUT – hex, jam, 3/8 inch NC |
| 18 | 70-5273T1 | 1 | LATCH – grille opening |
| 19 | 19-6266T1 | 1 | WASHER – lock, wave |
| 20 | 90-7524T1 | 1 | SPRING – latch |
| 21 | 496-81023 | 1 | WASHER – flat, 13/32 x 3/4 x 7/32 inch, hardened, latch, replaces 70-5177T1 spacer |
| 22 | 496-41041 | 2 | WASHER – flat, 13/32 x 1-1/8 x 9/64 inch, hardened |
| 23 | 70-5258T2 | 1 | SEAL – foam, adhesive-backed |
| 24 | 70-5812T1 | 1 | CLEVIS – pulley |
| 25 | 70-5808T1 | 1 | PULLEY – wire rope |
| 26 | 427-4077 | 1 | PIN, CLEVIS, 1/4″ x .770″, Hardened |
| 27 | 432-412 | 1 | 1/16″ x 3/4″ |
| 28 | 70-6732T1 | 1 | ROPE – wire, 4521 mm (178 inch) long, cut from 70-5252T1 bulk rope, see below |
| 1 | 60-7048T1 | 1 | MOUNT – monitor |
| 2 | 60-6820T1 | 1 | BRACKET – mounting, phone |
| 3 | 426-616 | 4 | BOLT, Hex, 3/8″-16 x 1″, G8, Full Thd |
| 4 | 426-68 | 2 | BOLT – hex, 3/8 NC x 1/2 inch, grade 8 |
| 5 | 495-21044 | 4 | WASHER – flat, 7/16 x 1 x 5/64 inch |
| 6 | 103226A1 | 2 | CLAMP – mounting bracket |
| 7 | 103213A1 | 2 | BRACKET – mounting |
| 9 | 614-8025 | 4 | BOLT – hex, full threads, 8 – 1.25 x 25 mm |
| 10 | 829-1408 | 4 | NUT, M8, Cl 10 |
| 8 | 895-11008 | 4 | WASHER – flat, 9 x 17 x 1.6 mm |
| 1 | 60-7086T2 | 1 | FRAME – cab |
| 3 | 60-5778T1 | 1 | HANDLE – grab, side |
| 4 | 495-21044 | 4 | WASHER – flat, 7/16 x 1 x 5/64 inch |
| 5 | 426-610 | 4 | BOLT – hex, 3/8 NC x 5/8 inch, grade 8 |
| 6 | 60-4315T1 | 1 | WINDSHIELD – front, center |
| 7 | 60-6866T1 | 2 | WINDSHIELD – front, sides |
| 8 | 60-6875T1 | 1 | SEAL – moulding, 5415 mm (213-3/16 inch) long, cut from 60-6870T1 bulk seal, see below |
| 9 | 60-3039T1 | 1 | SEAL – 625 mm (24-5/8 inch) long, cut from 2-6789T1 bulk seal, see below |
| 10 | 60-2774T1 | 2 | CLIP – retainer |
| 11 | 60-3040T1 | 2 | SEAL – 584 mm (23 inch) long, cut from 2-6789T1 bulk seal, see below, front side windshield |
| 12 | 60-4146T1 | 2 | BRACKET – retainer |
| 13 | 282-44712 | 4 | SCREW – self-drilling tapping, hex washer head, 1/4 NC x 3/4 inch |
| 14 | 60-6688T1 | 4 | SCREW – hex washer head, self-tapping, special |
| 15 | 60-6865T1 | 1 | WINDOW – door |
| 16 | 60-6876T1 | 1 | SEAL – moulding, 3575 mm (140-3/4 inch) long, cut from 60-6870T1 bulk seal, see below |
| 17 | 60-6863T1 | 1 | WINDOW – side |
| 18 | 60-6874T1 | 1 | SEAL – moulding, 3303 mm (130-1/16 inch) long, cut from 60-6870T1 bullk seal, see below |
| 19 | 60-3859T1 | 1 | WINDOW – back, center |
| 20 | 60-6864T1 | 2 | WINDOW – back, sides |
| 21 | 60-6877T1 | 1 | SEAL – moulding, 5054 mm (199 inch) long, cut from 60-6871T1 bulk seal, rear windows, see below |
| 22 | 20-1814T1 | 1 | SLEEVE – heat shrink, 19 mm (3/4 inch) long, cut from 20-1830T1 bulk sleeve, see below |
| 23 | 2-6879T1 | 1 | DECAL – emergency exit |
| 25 | 60-4582T1 | 13 | PLUG – hole, nylon, 5/16 inch diameter |
| 26 | 31-2175 | 4 | PLUG – hole, 3/4 inch diameter |
| 27 | 60-4401T1 | 2 | PLUG – hole, 5/8 inch diameter |
| 28 | 60-7040T1 | 1 | MOUNT – mirror, left-hand |
| 29 | 60-7068T1 | 1 | MOUNT – mirror, right-hand |
| 30 | 1283403C1 | 2 | MIRROR – rear view |
| 32 | 892-11010 | 2 | WASHER – lock, 10 mm |
| 33 | 495-11041 | 4 | WASHER – flat, 13/32 x 13/16 x 1/16 inch |
| 34 | 426-612 | 4 | BOLT – hex, 3/8 NC x 3/4 inch, grade 8 |
| 35 | 60-6895T1 | 1 | SEAL – 5055 mm (199 inch) long, order from 60-6872T1 bulk seal |
| 31 | 829-1410 | 2 | NUT, M10, Cl 10 |
| 1 | 60-7087T1 | 1 | FRAME – ROPS, protective |
| 2 | 60-5778T1 | 1 | HANDLE – grab, side |
| 3 | 495-21044 | 4 | WASHER – flat, 7/16 x 1 x 5/64 inch |
| 4 | 426-610 | 4 | BOLT – hex, 3/8 NC x 5/8 inch, grade 8 |
| 5 | 60-5855T1 | 1 | GUARD – wire, ROPS post |
| 6 | 281-1358 | 6 | SCREW – self-tapping, hex washer head, No. 10 NC x 1/2 inch |
| 7 | 495-31022 | 6 | WASHER, #10 |
| 8 | 515-23381 | 2 | CLAMP, 1 1/2″, Insul, 3/8″ Bolt, P-type |
| 9 | R46464 | 1 | BOX – operators manual |
| 10 | 463-41012 | 1 | SCREW – machine, hex slotted washer head, No. 10 NC x 3/4 inch |
| 11 | 60-6468T2 | 1 | DECAL – Warning, avoid injury or death |
| 12 | 60-7040T1 | 1 | MOUNT – mirror, left-hand |
| 13 | 60-7068T1 | 1 | MOUNT – mirror, right-hand |
| 14 | 1283403C1 | 2 | MIRROR – rear view |
| 16 | 892-11010 | 2 | WASHER – lock, 10 mm |
| 17 | 495-11034 | 4 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 18 | 426-612 | 4 | BOLT – hex, 3/8 NC x 3/4 inch, grade 8 |
| 15 | 829-1410 | 2 | NUT, M10, Cl 10 |
| 1 | 413-1672 | 4 | BOLT – hex, 1 NC x 4-1/2 inch |
| 2 | 60-5033T1 | 4 | WASHER – special, 1-1/16 x 3-1/4 x 1/4 inch thick |
| 3 | 60-4379T1 | 4 | MOUNT – rubber isolator |
| 4 | 60-4378T1 | 4 | SPACER – 1-1/16 x 3-5/8 x 1/4 inch thick |
| 5 | 19-5739 | 4 | WASHER – flat, special |
| 6 | 231-14416 | 4 | NUT – hex, self-locking, 1 inch NC |
| 1 | 60-5970T1 | 1 | CAP – roof top |
| 2 | 60-4657T1 | 1 | INSULATION – roof, cab only |
| 3 | 60-4450T2 | 1 | INSULATION – roof, cab only |
| 4 | 426-424 | 8 | BOLT – hex, 1/4 NC x 1-1/2 inch, grade 8 |
| 5 | 9421394 | 16 | WASHER – flat, 1/4 x 1 x 1/16 inch |
| 6 | 60-1826T1 | 16 | BUSHING – roof snubber |
| 7 | 60-4584T1 | 8 | SPACER – bushing |
| 8 | 60-4583T1 | 1 | SEAL – foam, 5791 mm (228 inch) long, cut from 60-4595T1 bulk seal, see below |
| 9 | 231-1444 | 8 | NUT, LOCK, 1/4″-20, GB |
| 10 | 31-2595 | 3 | PLUG – lift holes |
| 2 | 60-6342T2 | 1 | PLATE – floor access, front |
| 3 | 60-6307T1 | 1 | PLATE – floor access, rear |
| 5 | 60-6308T5 | 1 | PAD – noise, floor |
| 6 | 60-6343T2 | 1 | FLOORMAT – front |
| 7 | 60-6309T3 | 1 | FLOORMAT – rear |
| 8 | 231-1445 | 4 | NUT – hex, self-locking, 5/16 inch NC |
| 9 | 281-14812 | 13 | SCREW – self-tapping, hex washer head, 5/16 NC x 3/4 inch |
| 10 | 60-6565T1 | 1 | PAD – console insulation, floor |
| 11 | 60-4503T1 | 1 | PAD – console insulation, side |
| 12 | 60-4504T1 | 1 | PAD – console insulation, rear |
| 13 | 60-5935T1 | 1 | COVER – cab rear |
| 15 | 60-5011T3 | 1 | COVER – cab entrance |
| 16 | 443-1108 | 4 | SCREW – machine, flat Phillips, No. 10 NC x 1/2 inch |
| 17 | 60-4599T1 | 2 | STRIP – non skid, 25 (1) x 635 mm (25 inch) long, cut from 60-4598T1 bulk strip, see below |
| 18 | 60-4383T1 | 1 | GUARD – wire, cab post |
| 19 | 60-6688T1 | 6 | SCREW – hex washer head, self-tapping, special |
| 20 | 60-4403T1 | 1 | GUARD – wire, floor |
| 21 | 60-6010T1 | 1 | SEAL – 4191 mm (165 inch) long, cut from 60-4402T1X bulk seal, see below |
| 22 | 22-619 | 2 | GROMMET – closure |
| 23 | 60-6468T2 | 1 | DECAL – Warning, avoid injury or death, cab post |
| 24 | 60-4597T1 | 8 | SEAL – foam, 711 mm (28 inch) long, cut from 60-4596T1 bulk seal, see below |
| 25 | 60-6672T2 | 1 | PLATE – cover, Power Shift tractor |
| 26 | 60-6566T1 | 1 | PAD – console insulation, floor, Power Shift tractor |
| 27 | 426-512 | 4 | BOLT – hex, 5/16 NC x 3/4 inch, grade 8 |
| 30 | 60-6704T1 | 1 | INSULATION – cab firewall |
| 31 | 60-7021T1 | 2 | FOAM – sealing |
| 32 | 60-7022T1 | 2 | ANGLE – foam |
| 33 | 353-405 | 1 | PLUG – button, 9/16 inch |
| 33 | 22-619 | 1 | GROMMET – dome |
| 2 | 60-6342T2 | 1 | PLATE – floor access, front |
| 3 | 60-6307T1 | 1 | PLATE – floor access, rear |
| 4 | 281-14812 | 13 | SCREW – self-tapping, hex washer head, 5/16 NC x 3/4 inch |
| 5 | 60-4653T1 | 1 | PLATE – three point hitch |
| 9 | 60-5855T1 | 1 | GUARD – wire, ROPS post |
| 10 | 281-1358 | 6 | SCREW – self-tapping, hex washer head, No. 10 NC x 1/2 inch |
| 11 | 495-31022 | 2 | WASHER, #10 |
| 12 | 515-23381 | 2 | CLAMP, 1 1/2″, Insul, 3/8″ Bolt, P-type, Wire harness |
| 13 | 60-6468T2 | 1 | DECAL – Warning, avoid injury or death, cab post |
| 15 | 60-5866T1 | 1 | DECAL – Caution, when operating this vehicle use hearing protection |
| 16 | 231-1445 | 4 | NUT – hex, self-locking, 5/16 inch NC |
| 17 | 495-11034 | 13 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 18 | 60-4650T1 | 2 | SEAL – foam, 102 mm (4 inch) long, cut from 60-4596T1 bulk seal, see below |
| 1 | 60-7082T1 | 1 | DOOR – cab, service, Includes: Ref. 18, 19, 36, 37, 39, 40, 53, 54, 56, and 58 – 61 |
| 2 | 1280263C1 | 1 | CYLINDER – door |
| 3 | 3234063R1 | 2 | STUD – ball |
| 4 | 832-10410 | 1 | NUT, LOCK, M10 x 1.5, Cl 8 |
| 5 | 3233348R1 | 2 | CLIP – retaining |
| 8 | 60-6269T1 | 1 | COVER – latch housing |
| 9 | 60-6265T1 | 1 | HOUSING – latch |
| 10 | 60-6260T1 | 1 | BUSHING – pivot, handle |
| 11 | 60-6263T1 | 1 | LEVER – latch actuating |
| 12 | 60-6267T1 | 1 | GRIP – lever |
| 13 | 60-6261T1 | 1 | WASHER – flat, plastic |
| 14 | 19-5777 | 4 | NUT – hex, special |
| 17 | 1970023C1 | 1 | SPRING – latch |
| 18 | 427-4077 | 2 | PIN, CLEVIS, 1/4″ x .770″, Hardened |
| 19 | 432-48 | 2 | 1/16″ x 1/2″ |
| 20 | 60-5001T1 | 1 | LATCH – door |
| 21 | 443-13120 | 3 | SCREW – machine, flat Phillips, 5/16 NC x 1-1/4 inch |
| 22 | 495-21038 | 2 | WASHER – flat, 3/8 x 7/8 x 3/32 inch |
| 23 | 426-512 | 2 | BOLT – hex, 5/16 NC x 3/4 inch, grade 8 |
| 27 | 60-4193T1 | 1 | STRIKER – door, includes washer |
| 28 | 495-21044 | 1 | WASHER – flat, 7/16 x 1 x 5/64 inch |
| 29 | 231-4117 | 1 | NUT – hex, self-locking, 7/16 inch NC |
| 30 | 495-31022 | 3 | WASHER, #10 |
| 31 | 1-8674 | 3 | WASHER – trim |
| 32 | 60-6688T1 | 3 | SCREW – hex washer head, self-tapping, special |
| 33 | 60-5920T1 | 3 | CAP – trim, gray |
| 36 | 213-124 | 2 | CLEVIS – adjustable, 1/4 inch NF |
| 37 | 425-114 | 2 | NUT, 1/4″-28, G5 |
| 39 | 60-7047T1 | 1 | ROD – actuating, latch |
| 40 | 60-7083T1 | 1 | HANDLE – door |
| 53 | 131-837 | 2 | NUT, Tinn, U, 1/4″-20 |
| 54 | 60-7186T1 | 1 | COVER – door, lower, replaces 60-7081T1 cover |
| 56 | 426-416 | 1 | BOLT – hex, 1/4 NC x 1 inch, grade 8 |
| 57 | F64046 | 4 | WASHER – thrust, plastic |
| 58 | 60-7046T1 | 1 | ANGLE – latch actuating |
| 59 | 140-114 | 3 | SCREW, Cross Pan Hd, 1/4″-20 NC x 1″ |
| 60 | 425-104 | 3 | NUT – hex, 1/4 inch NC |
| 61 | 614-6016 | 3 | Bolt, Hex, M6 x 16, 8.8 |
| 62 | 60-6256T1 | 1 | STUD – anchor |
| 1 | 60-5966T1 | 1 | COVER – instrument panel |
| 2 | 60-5963T1 | 1 | PANEL – dash, left-hand |
| 3 | 60-5964T1 | 1 | PANEL – dash, right-hand |
| 4 | 60-4122T1 | 1 | STRAP – support, dash panel |
| 5 | 425-104 | 1 | NUT – hex, 1/4 inch NC |
| 6 | 19-6016 | 1 | BOLT – hex flange, 1/4 NC x 1/2 inch |
| 7 | 19-6119 | 4 | NUT – clip, U-type, No. 10 NC |
| 8 | 1-8674 | 8 | WASHER – trim |
| 9 | 163-46 | 8 | SCREW – machine, hex head, No. 10 NC x 1 inch |
| 10 | 60-5920T1 | 8 | CAP – trim, gray |
| 11 | 495-11028 | 4 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 12 | 60-4782T1 | 2 | PAD – insulation, dash |
| 13 | 225-14110 | 4 | NUT, #10-24 |
| 16 | 60-2008T1 | 2 | LOUVER – air deflecting |
| 17 | 60-1948T1 | 4 | BUSHING – flange, louver |
| 18 | 60-4019T2 | 4 | CLIP – retaining, louver |
| 19 | 280-13410 | 8 | SCREW – self-tapping, hex washer head, No. 8-18 x 5/8 inch |
| 20 | 60-4020T1 | 1 | MOUNT – dash, lower |
| 21 | 19-6016 | 4 | BOLT – hex flange, 1/4 NC x 1/2 inch |
| 22 | 426-824 | 4 | BOLT – hex, 1/2 NC x 1-1/2 inch, grade 8 |
| 23 | 495-21056 | 2 | WASHER – flat, 9/16 x 1-3/8 x 7/64 inch |
| 24 | 425-108 | 2 | NUT – hex, 1/2 inch NC |
| 1 | 60-5832T1 | 1 | PLATE – dash mounting |
| 2 | 60-5834T1 | 1 | COVER – dash wraparound |
| 3 | 340-11012 | 6 | SCREW – machine, pan Phillips, No. 10 NC x 3/4 inch |
| 4 | 19-6119 | 6 | NUT – clip, U-type, No. 10 NC |
| 5 | 60-5859T1 | 1 | TRIM – edge, 1194 mm (47 inch) long, cut from F64277X bulk trim, see below |
| 6 | 413-516 | 4 | BOLT – hex, 5/16 NC x 1 inch |
| 7 | 495-11034 | 4 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 8 | 231-1445 | 4 | NUT – hex, self-locking, 5/16 inch NC |
| 9 | 60-5836T1 | 1 | COVER – rear instrument panel |
| 10 | 60-5828T1 | 1 | SEAL – foam |
| 11 | 111626C1 | 6 | NUT – hex, self-locking, special, 1/4 inch NC |
| 12 | 353-401 | 2 | PLUG – button, 5/16 inch, replaces 60-4582T1 plug |
| 13 | 60-5980T1 | 1 | DECAL – master lamps, ROPS |
| 14 | 245334C1 | 2 | PLUG – panel switch cover, replaces 60-3210T1 plug |
| 1 | 60-6979T2 | 1 | PANEL – control |
| 2 | 60-6106T1 | 1 | PANEL – console wraparound |
| 3 | 60-6063T1 | 1 | COVER – console panel |
| 4 | 60-6416T1 | 1 | DECAL – control console |
| 5 | 60-6436T1 | 1 | COVER – console |
| 6 | 495-11034 | 5 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 7 | 231-1445 | 5 | NUT – hex, self-locking, 5/16 inch NC |
| 8 | 60-7055T1 | 1 | PLUG – slot |
| 9 | 64-146 | 1 | PLUG – hole, access |
| 10 | 60-4258T1 | 1 | PLUG – hole, flow control access |
| 11 | 97079C3 | 1 | BOX – operators manual |
| 12 | 426-424 | 3 | BOLT – hex, 1/4 NC x 1-1/2 inch, grade 8, used without deluxe storage compartment |
| 12 | 426-416 | 3 | BOLT – hex, 1/4 NC x 1 inch, grade 8, used with deluxe storage compartment |
| 13 | 495-11028 | 6 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 14 | 60-6062T1 | 3 | SPACER – manual box, used without deluxe storage compartment |
| 14 | 2-3010T1 | 3 | SPACER – manual box, used with deluxe storage compartment |
| 15 | 425-104 | 3 | NUT – hex, 1/4 inch NC |
| 16 | 60-4652T1 | 1 | COVER – plate, without three point hitch |
| 17 | 231-1445 | 4 | NUT – hex, self-locking, 5/16 inch NC |
| 19 | 60-7054T1 | 1 | PLUG – slot |
| 20 | 2-6138T91 | 1 | ASHTRAY – smokers |
| 21 | 473-10810 | 2 | SCREW – machine, flat head slotted, No. 8 NC x 5/8 inch |
| 22 | 131-29 | 2 | NUT – hex, self-locking, No. 8 NC |
| 23 | 432-820 | 5 | 1/8″ x 1-1/4″ |
| 26 | 19-6136 | 11 | STUD – quarter turn |
| 28 | 19-5668 | 11 | WASHER – flat, 1/4 x 3/4 x 3/16 inch |
| 29 | A36042 | 11 | RETAINER – quarter turn |
| 1 | 60-6982T2 | 1 | PANEL – control console |
| 2 | 60-6106T1 | 1 | PANEL – console wraparound |
| 3 | 60-6063T1 | 1 | COVER – console panel |
| 4 | 60-7065T1 | 1 | DECAL – control console |
| 5 | 60-6436T1 | 1 | COVER – console, The hole to the left of this pt is the cup holder. There is not a separate pt # for just a |
| 6 | 495-11034 | 5 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 7 | 231-1445 | 5 | NUT – hex, self-locking, 5/16 inch NC |
| 8 | 60-7055T1 | 1 | PLUG – slot |
| 9 | 60-7054T1 | 1 | PLUG – slot |
| 10 | 432-820 | 5 | 1/8″ x 1-1/4″ |
| 11 | 97079C3 | 1 | BOX – operators manual |
| 12 | 426-424 | 3 | BOLT – hex, 1/4 NC x 1-1/2 inch, grade 8, used without deluxe storage compartment |
| 12 | 426-416 | 3 | BOLT – hex, 1/4 NC x 1 inch, grade 8, used with deluxe storage compartment |
| 13 | 495-11028 | 6 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 14 | 60-6062T1 | 3 | SPACER – manual box, used without deluxe storage compartment |
| 14 | 2-3010T1 | 3 | SPACER – manual box, used with deluxe storage compartment |
| 15 | 425-104 | 3 | NUT – hex, 1/4 inch NC |
| 20 | 2-6138T91 | 1 | ASHTRAY – smokers |
| 21 | 473-10810 | 2 | SCREW – machine, flat head slotted, No. 8 NC x 5/8 inch |
| 22 | 131-29 | 2 | NUT – hex, self-locking, No. 8 NC |
| 26 | 19-6136 | 11 | STUD – quarter turn |
| 28 | 19-5668 | 11 | WASHER – flat, 1/4 x 3/4 x 3/16 inch |
| 29 | A36042 | 11 | RETAINER – quarter turn |
| 30 | 60-4258T1 | 4 | PLUG – hole, flow control access |
| 31 | 64-146 | 1 | PLUG – hole, access |
| 1 | 60-6979T2 | 1 | PANEL – control |
| 2 | 60-6386T1 | 1 | PANEL – console, wraparound |
| 3 | 60-7055T1 | 1 | PLUG – slot |
| 4 | 60-6416T1 | 1 | DECAL – control console |
| 5 | 60-6436T1 | 1 | COVER – console |
| 6 | 495-11034 | 5 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 7 | 231-1445 | 5 | NUT – hex, self-locking, 5/16 inch NC |
| 8 | 64-146 | 1 | PLUG – hole, access |
| 9 | 60-4258T1 | 1 | PLUG – hole, flow control access |
| 13 | 2-6138T91 | 1 | ASHTRAY – smokers |
| 14 | 473-10810 | 2 | SCREW – machine, flat head slotted, No. 8 NC x 5/8 inch |
| 15 | 131-29 | 2 | NUT – hex, self-locking, No. 8 NC |
| 16 | 22-619 | 1 | GROMMET – plug |
| 17 | 60-7054T1 | 1 | PLUG – slot |
| 18 | 432-820 | 5 | 1/8″ x 1-1/4″ |
| 19 | 19-6136 | 11 | STUD – quarter turn |
| 21 | 19-5668 | 7 | WASHER – flat, 1/4 x 3/4 x 3/16 inch |
| 22 | A36042 | 11 | RETAINER – quarter turn |
| 1 | 60-6982T2 | 1 | PANEL – control console |
| 2 | 60-6386T1 | 1 | PANEL – console, wraparound |
| 3 | 60-7055T1 | 1 | PLUG – slot |
| 4 | 60-7065T1 | 1 | DECAL – control console |
| 5 | 60-6436T1 | 1 | COVER – console |
| 6 | 495-11034 | 5 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 7 | 231-1445 | 5 | NUT – hex, self-locking, 5/16 inch NC |
| 8 | 64-146 | 1 | PLUG – hole, access |
| 9 | 60-4258T1 | 1 | PLUG – hole, flow control access |
| 13 | 2-6138T91 | 1 | ASHTRAY – smokers |
| 14 | 473-10810 | 2 | SCREW – machine, flat head slotted, No. 8 NC x 5/8 inch |
| 15 | 131-29 | 2 | NUT – hex, self-locking, No. 8 NC |
| 16 | 22-619 | 1 | GROMMET – plug hole |
| 17 | 60-7054T1 | 1 | PLUG – slot |
| 18 | 432-820 | 5 | 1/8″ x 1-1/4″ |
| 19 | 19-6136 | 11 | STUD – quarter turn |
| 21 | 19-5668 | 7 | WASHER – flat, 1/4 x 3/4 x 3/16 inch |
| 22 | A36042 | 11 | RETAINER – quarter turn |
| 2 | 60-6254T3 | 1 | HEADLINER – cab |
| 3 | 495-31022 | 8 | WASHER, #10 |
| 4 | 1-8674 | 6 | WASHER – trim |
| 5 | 60-6688T1 | 6 | SCREW – hex washer head, self-tapping, special |
| 6 | 60-5920T1 | 6 | CAP – trim, gray |
| 7 | 19-5668 | 6 | WASHER – flat, 1/4 x 3/4 x 3/16 inch |
| 8 | 495-11034 | 3 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 9 | 425-105 | 3 | NUT – hex, 5/16 inch NC |
| 10 | 60-6351T1 | 1 | PAD – insulation |
| 11 | 70-5275T1 | 2 | CLAMP – includes U-bolt and nut |
| 12 | 60-4137T1 | 2 | ROPE – plastic coated wire, 394 mm (15-1/2 inch) long, cut from 70-5252T1 bulk rope, see below |
| 13 | 70-5269T1 | 4 | FERRULE – wire rope |
| 14 | 131-837 | 2 | NUT, Tinn, U, 1/4″-20 |
| 15 | 60-5924T1 | 1 | PAD – insulation, gray |
| 16 | 60-6516T1 | 1 | HARNESS – overhead, cab |
| 18 | 24379R1 | 2 | SCREW – self-tapping, pan Phillips, No. 8-18 x 1/2 inch |
| 19 | 60-5922T1 | 2 | PAD – speaker cover, gray |
| 20 | A177462 | 1 | MIRROR – rear view, includes mounting hardware, Includes: Ref. 21 & 22 |
| 21 | 493-41026 | 1 | WASHER – external tooth lock, 1/4 inch |
| 22 | 19-5565 | 1 | NUT – hex, self-locking, 1/4 inch NF |
| 23 | 64-86T3 | 1 | BRACKET – rear view mirror |
| 24 | 463-41012 | 2 | SCREW – machine, hex slotted washer head, No. 10 NC x 3/4 inch |
| 25 | 86632551 | 2 | NUT, LOCK, #10-24, GB |
| 34 | 83882C91 | 1 | LAMP ASSEMBLY – console illumination, Includes: Ref. 35 & 36 |
| 35 | 107329C1 | 1 | SOCKET AND CABLE – bulb |
| 36 | D71346 | 1 | BULB – lamp, No. 168 |
| 37 | 492-11010 | 2 | Washer, Lock, #10 |
| 38 | 60-6256T1 | 1 | STUD – anchor |
| 39 | 80679 | 2 | Washer, Lock, 1/2″ |
| 40 | 426-816 | 1 | BOLT – hex, 1/2 NC x 1 inch, grade 8 |
| 2 | 60-5758T1 | 1 | DOOR – overhead, console |
| 3 | 60-5923T1 | 1 | PAD – insulation, door, gray |
| 4 | 1964752C1 | 1 | SWITCH – rocker, master light |
| 5 | 245012C1 | 1 | SWITCH – rocker, dash lights |
| 6 | 1964751C1 | 1 | SWITCH – rocker, ether start, if equipped |
| 7 | 245334C1 | 2 | PLUG – panel switch cover, replaces 60-3210T1 plug |
| 8 | 60-7153T1 | 1 | DECAL – overhead controls |
| 9 | 60-6459T1 | 1 | PANEL – rocker switch |
| 10 | 60-5928T1 | 1 | COVER – console door, gray |
| 11 | 363-30812 | 8 | SCREW – machine, hex washer head, No. 8 NC x 3/4 inch |
| 12 | 131-29 | 8 | NUT – hex, self-locking, No. 8 NC |
| 13 | 60-4033T1 | 2 | KNOB ASSEMBLY – console release, no longer available, order component parts, Includes: Ref. 13A |
| 14 | 19-6126 | 2 | SPACER – knob |
| 15 | 661406R1 | 2 | WASHER – locking, replaces 267689R1 ring |
| 16 | 459-5108 | 4 | SCREW – machine, pan head slotted, No. 10 NF x 1/2 inch |
| 17 | 20-1451T1 | 1 | BLOCK – junction |
| 18 | 193-1000 | 4 | NUT – hex, with external tooth lock washer, No. 10 NF |
| 19 | 60-4034T1 | 1 | HINGE – console door |
| 20 | 426-48 | 3 | BOLT – hex, 1/4 NC x 1/2 inch, grade 8 |
| 21 | 495-11028 | 3 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 22 | 231-1444 | 3 | NUT, LOCK, 1/4″-20, GB |
| 23 | 495-21019 | 8 | WASHER, #8 |
| 24 | 495-11034 | 3 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 25 | 425-105 | 3 | NUT – hex, 5/16 inch NC |
| 26 | 495-31022 | 2 | WASHER, #10 |
| 27 | 1987431C1 | 1 | SWITCH – rocker, if equipped |
| 1 | 60-6254T4 | 1 | HEADLINER – cab |
| 2 | 1983391C1 | 1 | LAMP – dome, Includes: Ref. 3 |
| 3 | E35556 | 1 | BULB – lamp 12V, 10w |
| 6 | 163-45 | 2 | SCREW – machine, hex head, No. 10 NC x 1/2 inch |
| 7 | 495-31022 | 2 | WASHER, #10 |
| 8 | 225-14110 | 2 | NUT, #10-24 |
| 9 | 60-6299T1 | 1 | PLATE – mounting, lamp |
| 10 | 60-4029T1 | 1 | PLATE – diffuse, lamp |
| 11 | B50213 | 2 | BULB – lamp, No. 53 |
| 13 | 60-5748T1 | 2 | SPEAKER – radio |
| 14 | 440-11010 | 8 | SCREW – machine, pan Phillips, No. 10 NC x 5/8 inch |
| 15 | 60-6516T1 | 1 | HARNESS – overhead, cab |
| 19 | 340-1108 | 2 | SCREW – machine, pan Phillips, No. 10 NC x 1/2 inch |
| 20 | 60-6518T1 | 1 | BRACKET – mounting, switch |
| 21 | 60-6515T1 | 1 | SWITCH – lamp, door |
| 22 | 19-1035 | 2 | SCREW – machine, round head, No. 4 NC x 1 inch |
| 23 | 495-31016 | 2 | WASHER – flat, 5/32 x 3/8 x 3/64 inch |
| 24 | 225-14104 | 2 | NUT, #4-40 |
| 25 | 495-31022 | 2 | WASHER, #10 |
| 26 | 60-6579T1 | 1 | SEAL – switch |
| 1 | 134181A2 | 1 | KIT – seat top, without armrest, Includes: Ref. 4 & 5 |
| 2 | 132886A1 | 1 | KIT – backrest, cloth, complete with lumbar knob, without armrest, Includes: Ref. 4 & 5 |
| 3 | 132888A2 | 1 | KIT – seat cushion, with structure, Includes: Ref. 4 & 5 |
| 11 | 143199A1 | 1 | ARMREST – right-hand, black, Includes: one drive pin |
| 12 | 132882A1 | 1 | ARMREST – left-hand, black |
| 13 | 132883A1 | 1 | KIT – left-hand armrest adjustment |
| 14 | 413-528 | 1 | BOLT – hex, 5/16 NC x 1-3/4 inch |
| 15 | 495-11034 | 1 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 16 | 413-544 | 2 | BOLT – hex, 5/16 NC x 2-3/4 inch |
| 17 | 1343875C1 | 2 | SPACER – 25/64 ID x 1/2 inch |
| 19 | 38-31016 | 2 | Pin, 5/32″ x 1″, Coiled |
| 25 | 1343982C1 | 1 | BELT – seat |
| 27 | 328-724 | 1 | BOLT, Hex, 7/16″-20 x 1 1/2″, G8 |
| 28 | 328-732 | 1 | BOLT, Hex, 7/16″-20 x 2″, G8 |
| 29 | 413-544 | 2 | BOLT – hex, 5/16 NC x 2-3/4 inch |
| 31 | 395-11053 | 2 | WASHER – flat, 17/32 x 1-1/16 x 3/32 inch |
| 32 | 232-4117 | 2 | NUT, LOCK, 7/16″-14, GC |
| 33 | 132868A1 | 1 | KIT – height adjustment, Includes: (3) cover plates, (1) rocker switch, and (4) screws |
| 34 | 141566A1 | 1 | PLATE – reinforcement |
| 35 | 176091A1 | 1 | KIT – retaining, hog ring, package of 48 rings for cushions |
| 3 | 117-109 | 4 | BOLT – square head, 5/16 NC x 3/4 inch |
| 4 | 413-520 | 4 | BOLT – hex, 5/16 NC x 1-1/4 inch |
| 5 | 230-4215 | 8 | NUT – hex, self-locking, 5/16 inch NC |
| 6 | 135513A1 | 1 | SPRING – torsion, left-hand |
| 7 | 135514A1 | 1 | SPRING – torsion, right-hand |
| 10 | 100-3325 | 2 | Ring, Retaining, #25, .207″ Dia, E-Type (Replaces 103-1131), Part of retainer kit P/N 175088A1. |
| 11 | 134144A1 | 8 | SPACER – plate |
| 12 | 134146A1 | 1 | LEVER – slide control |
| 14 | 413-816 | 1 | BOLT – hex, 1/2 NC x 1 inch |
| 20 | 495-11041 | 2 | WASHER – flat, 13/32 x 13/16 x 1/16 inch, one required |
| 21 | 230-4715 | 2 | NUT – hex, self-locking, 5/16 inch NF, one required |
| 23 | 100-3331 | 2 | Ring, Retaining, #X31, .243″ Dia, E-Type, Part of retainer kit P/N 175088A1. |
| 27 | L18337 | 3 | STRAP – tie, 15 inch, nylon |
| 31 | L18337 | 3 | STRAP – tie, 15 inch, nylon |
| 37 | 134148A1 | 1 | PLATE – swivel |
| 38 | 132878A2 | 1 | PLATE – lateral isolator, Includes: Ref. 13 – 21 on Figure 9-062 and Ref. 50 – 55 below |
| 39 | 413-532 | 4 | BOLT – hex, 5/16 NC x 2 inch |
| 40 | 413-510 | 4 | BOLT – hex, 5/16 NC x 5/8 inch |
| 41 | 231-4115 | 4 | NUT – hex, self-locking, 5/16 inch NC |
| 42 | 495-11034 | 2 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 46 | 135510A1 | 1 | ROD – isolator, Includes: knob |
| 47 | 38-31012 | 2 | Pin, 5/32″ x 3/4″, Coiled |
| 48 | 135511A1 | 1 | ROD – swivel, Includes: knob |
| 49 | A47375 | 1 | SPRING – detent |
| 52 | 433-512 | 4 | BOLT – carriage, 5/16 NC x 3/4 inch |
| 53 | 231-4115 | 4 | NUT – hex, self-locking, 5/16 inch NC |
| 54 | 1344025C1 | 1 | PIN – clevis |
| 55 | 100-3350 | 1 | Ring, Retaining, #50, .392″ Dia, E-Type (Replaces A27804) |
| 1 | 1990642C1 | 1 | HOUSING – upper, suspension |
| 2 | 132862A1 | 1 | ARM – suspension |
| 3 | A49529 | 1 | SHAFT – bushing tube |
| 4 | 230-4216 | 1 | NUT – hex, self-locking, 3/8 inch NC |
| 5 | 1981834C1 | 1 | HOUSING – lower |
| 6 | 443-13812 | 1 | SCREW – machine, flat Phillips, 3/8 NC x 3/4 inch |
| 8 | 413-68 | 1 | BOLT – hex, 3/8 NC x 1/2 inch |
| 9 | 131-425 | 1 | NUT – push-on type, 1/2 inch |
| 13 | 495-11041 | 2 | WASHER – flat, 13/32 x 13/16 x 1/16 inch |
| 14 | 132867A1 | 1 | HARNESS – wire |
| 26 | 131-425 | 1 | NUT – push-on type, 1/2 inch |
| 28 | 138-317 | 1 | PIN, 1/8″ x 5/8″, Slotted |
| 30 | 144514A1 | 1 | BRACKET – cable control |
| 34 | 434-48 | 2 | Bolt, Carriage, Short NK, 1/4″-20 x 1/2″, G5, Full Thd |
| 35 | 231-1444 | 2 | NUT, LOCK, 1/4″-20, GB |
| 36 | 495-11041 | 1 | WASHER – flat, 13/32 x 13/16 x 1/16 inch |
| 39 | 230-4715 | 1 | NUT – hex, self-locking, 5/16 inch NF |
| 42 | 1981845C1 | 1 | ANGLE – mounting, shock |
| 45 | L18337 | 2 | STRAP – tie, 15 inch, nylon |
| 47 | 179026A1 | 1 | SLEEVE – guard, 10 (3/8) ID x 615 mm (24-1/4 inch) long |
| 48 | L18337 | 3 | STRAP – tie, 15 inch, nylon |
| 49 | 230-4715 | 1 | NUT – hex, self-locking, 5/16 inch NF |
| 5 | 276-24812 | 2 | SCREW – self-tapping, hex head, 5/16 NC x 3/4 inch |
| 6 | 132863A1 | 1 | LATCH – isolator, fore/aft |
| 8 | 133422A1 | 2 | BUMPER – down stop |
| 11 | 231-1444 | 2 | NUT, LOCK, 1/4″-20, GB, Part of bumper kit P/N 180593A1. |
| 12 | 222771A1 | 2 | BRACKET – mounting, seat |
| 13 | 495-11034 | 4 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 14 | 614-8020 | 4 | BOLT – hex, full threads, 8 – 1.25 x 20 mm |
| 16 | F15988 | 4 | SPACER – seat mounting |
| 17 | 892-11008 | 4 | WASHER, LOCK, M8 |
| 18 | 829-1408 | 4 | NUT, M8, Cl 10 |
| 1 | 1987174C2 | 1 | SEAT ASSEMBLY – mechanical, with vinyl upholstery, parts list Figures 9-084 – 9-088 |
| 2 | 1977735C1 | 2 | BRACKET – mounting, seat |
| 3 | 614-8020 | 4 | BOLT – hex, full threads, 8 – 1.25 x 20 mm |
| 4 | 425-108 | 4 | NUT – hex, 1/2 inch NC |
| 5 | 495-21038 | 4 | WASHER – flat, 3/8 x 7/8 x 3/32 inch |
| 6 | 231-1445 | 4 | NUT – hex, self-locking, 5/16 inch NC |
| 3 | 1981820C2 | 1 | KIT – backrest cover and retainers, Includes: Ref. 4 |
| 4 | 1999693C1 | 1 | CLIP – christmas tree, package of 14 |
| 6 | 1999691C1 | 1 | KIT – seat knob |
| 8 | 38-11016 | 2 | Pin, 5/32″ x 1″, Slotted |
| 9 | 1343828C1 | 2 | CAM – seat tilt, no longer available, order 1343826C2 shaft assembly |
| 11 | 38-11016 | 1 | Pin, 5/32″ x 1″, Slotted |
| 12 | 1999691C1 | 1 | KIT – seat knob, replaces 1981828C1 knob |
| 13 | 138-303 | 1 | Pin, 3/16″ x 1 1/8″, Slotted |
| 20 | 1974711C1 | 1 | KNOB – backrest tilt |
| 21 | 30299R1 | 1 | SCREW – machine, 6 x 12 mm |
| 27 | 1981818C1 | 1 | KIT – armrest, left-hand, Includes: Ref. 28 |
| 29 | 143199A1 | 1 | ARMREST – right-hand, black, Includes: Ref. 30 |
| 31 | 1990647C2 | 1 | KIT – boot, suspension, Includes: Ref. 32 |
| 32 | 132872A1 | 24 | KIT – boot pin, package of 23 retainers and 3 dome nuts |
| 35 | 1975957C1 | 1 | BRACKET – seat belt |
| 36 | 1343982C1 | 1 | BELT – seat |
| 37 | 326-728 | 1 | BOLT, Hex, 7/16″-14 x 1 3/4″, G8 |
| 38 | 395-11053 | 3 | WASHER – flat, 17/32 x 1-1/16 x 3/32 inch |
| 39 | S5375 | 1 | SPACER – pipe, 3/8 x 3/8 inch |
| 40 | 232-4117 | 1 | NUT, LOCK, 7/16″-14, GC |
| 43 | 113-70 | 2 | BOLT, Hex, 1/4″-20 x 2″, G5 |
| 44 | 328-724 | 1 | BOLT, Hex, 7/16″-20 x 1 1/2″, G8 |
| 1 | 1343857C1 | 1 | PLATE – swivel, upper |
| 2 | 1343858C1 | 1 | PLATE – swivel, lower |
| 5 | 1343859C1 | 1 | RETAINER – swivel |
| 6 | 1343860C1 | 1 | PLATE – swivel bearing |
| 7 | 413-620 | 4 | BOLT – hex, 3/8 NC x 1-1/4 inch |
| 8 | 230-4216 | 4 | NUT – hex, self-locking, 3/8 inch NC |
| 9 | A49555 | 1 | RETAINER – ball |
| 10 | 211-1016 | 8 | BALL – chrome alloy steel, 1/2 inch, grade 24 |
| 11 | N8680 | 1 | SPRING – latch rod |
| 20 | 1343861C1 | 1 | BRACKET – swivel rod |
| 21 | 49-36 | 2 | RIVET – truss head, 3/16 x 3/8 inch |
| 22 | 1343862C2 | 1 | ROD – swivel |
| 23 | 1999692C1 | 1 | KIT – knob, replaces 1343863C1 knob |
| 24 | 1981825C1 | 1 | WIRE – slide |
| 25 | 426-512 | 4 | BOLT – hex, 5/16 NC x 3/4 inch, grade 8 |
| 26 | 495-11034 | 4 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 27 | 230-4115 | 8 | NUT – hex, self-locking, 5/16 inch NC |
| 28 | 417-512 | 4 | BOLT – square head, 5/16 NC x 3/4 inch, grade 2 |
| 29 | 1981823C1 | 1 | SLIDE – seat, right-hand |
| 30 | 1981822C1 | 1 | SLIDE – seat, left-hand, with handle |
| 1 | 1981787C1 | 1 | HOUSING – lower |
| 2 | 1344249C1 | 6 | KIT – roller tube and bearing |
| 3 | 1981789C1 | 1 | ARM – suspension |
| 4 | 128115A1 | 1 | SHAFT – spring |
| 5 | 123968A2 | 2 | KIT – weight adjustment spring, replaces 1981791C1 bushing |
| 6 | 1981792C1 | 1 | ARM – mounting |
| 7 | A45519 | 5 | WASHER – flat, plastic, special, 33/64 x 1-1/8 x 1/16 inch, order A45110 spacer and A45116 spacer |
| 8 | A47760 | 4 | TUBE – bearing |
| 9 | 180609A1 | 2 | KIT – bumper, replaces 1981793C1 bumper |
| 10 | 440-11010 | 2 | SCREW – machine, pan Phillips, No. 10 NC x 5/8 inch |
| 11 | 230-42409 | 2 | NUT – hex, self-locking, No. 10 NC |
| 19 | 1981794C1 | 2 | SPRING – external |
| 20 | 1344250C2 | 1 | KIT – shock absorber |
| 21 | 123967A1 | 1 | KIT – cam follower |
| 22 | A49529 | 2 | SHAFT – bushing tube |
| 23 | 1981821C1 | 1 | HOUSING – upper |
| 24 | 1981798C1 | 1 | CAM – low profile |
| 25 | 1981799C1 | 1 | BEARING – cam follower |
| 26 | 123966A1 | 1 | KIT – height adjustment |
| 27 | 119001A1 | 1 | ARM ASSEMBLY – cam |
| 28 | 138-110 | 1 | PIN, LOCK, 7/32″ x 3/4″, Slotted |
| 29 | 138-172 | 2 | PIN, 3/8″ x 1 1/4″, Slotted |
| 30 | 1987116C2 | 2 | KIT – weight adjuster, replaces 1981802C1 race |
| 31 | F13537 | 1 | BEARING – thrust |
| 36 | 1987116C2 | 1 | KIT – weight adjuster |
| 37 | 38-11016 | 1 | Pin, 5/32″ x 1″, Slotted |
| 38 | 38-11010 | 1 | Pin, 5/32″ x 5/8″, Slotted |
| 39 | 38-21010 | 1 | Pin, 5/32″ x 5/8″, Coiled |
| 40 | 1974732C1 | 1 | WASHER – flat, 25/64 x 1-1/8 x 1/8 inch |
| 41 | A45501 | 2 | BEARING – shock absorber |
| 42 | A49623 | 2 | RING – retaining |
| 43 | 131-425 | 2 | NUT – push-on type, 1/2 inch |
| 44 | 230-4216 | 2 | NUT – hex, self-locking, 3/8 inch NC |
| 46 | 138-155 | 1 | PIN, 5/16″ x 1 1/4″, Slotted |
| 47 | 1981807C1 | 1 | GUIDE – weight adjustment |
| 50 | 151-537 | 1 | RIVET – break mandrel, 1/8 x 21/32 inch |
| 59 | 230-4115 | 1 | NUT – hex, self-locking, 5/16 inch NC |
| 60 | 438-11214 | 1 | Pin, 3/16″ x 7/8″, Slotted |
| 61 | 495-11034 | 2 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 1 | 60-6366T91 | 1 | CONTAINER ASSEMBLY – storage compartment, Includes: Ref. 2 |
| 5 | 60-6362T91 | 1 | CONTAINER ASSEMBLY – storage compartment, Includes: Ref. 6 |
| 9 | 60-6370T1 | 1 | COVER – door, storage compartment |
| 10 | 60-6369T1 | 1 | COVER – door |
| 11 | 60-6372T2 | 1 | DOOR – storage compartment |
| 12 | 60-6371T2 | 1 | COVER – door |
| 13 | 60-6360T1 | 1 | HINGE – door |
| 14 | 60-6361T1 | 1 | HINGE – door |
| 15 | 60-6358T1 | 1 | TRIM – edge, 63 mm (2-1/2 inch) long, cut from F64277X bulk trim, see below |
| 16 | 60-6359T1 | 1 | TRIM – edge, 194 mm (7-5/8 inch) long, cut from F64277X bulk trim, see below |
| 17 | 60-6374T2 | 4 | SPRING – cover |
| 18 | 425-108 | 6 | NUT – hex, 1/2 inch NC, mounting, seat |
| 19 | 495-11028 | 6 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 20 | 426-424 | 6 | BOLT – hex, 1/4 NC x 1-1/2 inch, grade 8 |
| 21 | 60-5920T1 | 12 | CAP – trim, gray |
| 22 | 1-8674 | 12 | WASHER – trim |
| 23 | 463-3108 | 23 | SCREW – machine, hex washer head, No. 10 NC x 1/2 inch |
| 24 | 193-1004 | 23 | NUT – hex, with external tooth lock washer, No. 10 NC |
| 25 | 495-31022 | 20 | WASHER, #10 |
| 29 | 60-6354T2 | 1 | COVER – cab post, right-hand rear |
| 30 | 60-6352T2 | 1 | COVER – cab post, left-hand rear |
| 31 | 60-6353T1 | 1 | COVER – cab post, left-hand front |
| 32 | 60-6355T1 | 1 | COVER – cab frame, rear |
| 33 | 3234176R1 | 1 | HOOK – coat |
| 34 | 60-6520T1 | 1 | PLATE – coat hook |
| 35 | 280-16516 | 1 | SCREW – self-tapping, hex washer head, No. 10 – 16 x 1 inch |
| 39 | 1971228C1 | 1 | VISOR – sun |
| 40 | 60-6521T1 | 1 | PLATE – mounting, sun visor |
| 41 | 343-11016 | 3 | SCREW – machine, flat Phillips, No. 10 NC x 1 inch |
| 45 | 60-6531T1 | 2 | SEAL – foam, 292 mm (11-1/2 inch) long, cut from 60-4596T1 bulk seal, see below |
| 46 | 2-3010T1 | 1 | SPACER – manual box, hook, replaces 60-6576T1 spacer |
| 1 | 60-6973T91 | 1 | MODULE ASSEMBLY – air conditioning and heating, parts list Figures 9-094 and 9-096 |
| 3 | 495-21044 | 4 | WASHER – flat, 7/16 x 1 x 5/64 inch |
| 4 | 1-1051 | 1 | GROMMET – harness protection |
| 5 | 425-106 | 4 | NUT, 3/8″-16, G5 |
| 6 | 60-3846T2 | 1 | FILTER – air recirculation |
| 7 | 60-6706T1 | 1 | FILTER – air recirculation, cab |
| 1 | 60-6692T3 | 1 | HOUSING – module |
| 3 | 60-6685T1 | 1 | COVER – module |
| 4 | 60-6674T1 | 1 | HOUSING – filter |
| 5 | 60-6318T91 | 1 | LATCH – module |
| 6 | 19-5422 | 2 | SCREW – machine, truss head, No. 8 NC x 3/4 inch |
| 7 | 193-1002 | 2 | NUT – hex, with external tooth lock washer, No. 8 NC |
| 8 | 60-6675T1 | 1 | BRACKET – filter box |
| 9 | 260-1338 | 2 | SCREW – self-tapping, pan Phillips, No. 6-20 x 1/2 inch |
| 10 | 60-6703T1 | 1 | GASKET – filter box |
| 11 | 60-4452T2 | 1 | FILTER – air |
| 16 | 60-6677T1 | 1 | CORE – heater and evaporator |
| 17 | 128484A1 | 1 | O-RING – 7/16 ID x 1/16 inch wide |
| 18 | 128485A1 | 1 | O-RING – 9/16 ID x 1/16 inch wide |
| 19 | 60-6688T1 | 6 | SCREW – hex washer head, self-tapping, special |
| 20 | 1990756C2 | 1 | VALVE – expansion |
| 25 | 515-23238 | 1 | CLAMP – P-type, 15/16 inch ID |
| 27 | 426-612 | 1 | BOLT – hex, 3/8 NC x 3/4 inch, grade 8 |
| 28 | 425-106 | 1 | NUT, 3/8″-16, G5 |
| 29 | 1331087C1 | 1 | VALVE – control |
| 31 | 214-1408 | 2 | CLAMP – adj, 1/2 – 29/32 inch dia |
| 32 | 60-6698T1 | 1 | PAD – foam, module cover |
| 33 | 60-6817T1 | 1 | PAD – core sealing, 1-3/4 x 1-3/4 x 18-3/4 inch long |
| 1 | 60-6692T3 | 1 | HOUSING – module |
| 3 | 60-6696T2 | 1 | PAD – insulating foam, front |
| 4 | 60-6697T1 | 1 | PAD – insulating foam, right-hand |
| 5 | 60-6699T2 | 1 | PAD – insulating foam, lower |
| 6 | 60-6701T1 | 1 | PAD – insulating foam, upper |
| 7 | 60-6702T2 | 2 | PAD – insulating foam, filler |
| 8 | 60-6328T1 | 1 | FILTER – foam, air inlet |
| 9 | 1977564C2 | 1 | BLOWER – cab, component parts not serviced separately |
| 10 | 1343938C2 | 1 | RESISTOR – blower, cab air |
| 14 | 60-6852T2 | 1 | FAN – blower, pressurizer, includes motor shaft retaining clip |
| 15 | 495-31022 | 2 | WASHER, #10 |
| 16 | 9411893 | 2 | NUT – hex, self-locking, No. 10 NF |
| 17 | 60-6851T1 | 1 | MOTOR – fan, blower, with 5/16 inch diameter shaft |
| 18 | 31-2475 | 1 | GROMMET – harness protection |
| 19 | 60-6707T1 | 1 | HARNESS – blower motor |
| 20 | 280-13512 | 25 | SCREW – self-tapping, hex washer head, No. 10-16 x 3/4 inch |
| 21 | 60-6708T1 | 11 | NUT – U-type, special |
| 22 | 1975905C1 | 5 | NUT – special, U-speed, No. 10-16 |
| 23 | 19-6157 | 10 | NUT – U-type, No. 10 |
| 24 | 60-6673T1 | 1 | PAN – condensation drip |
| 30 | 60-6694T2 | 1 | PRECLEANER – air inlet |
| 31 | 60-6695T1 | 1 | PLATE – support, blower motor |
| 32 | 60-6693T1 | 1 | HOUSING – blower fan |
| 33 | 19-1018 | 13 | SCREW – pan head, self-tapping, special, No. 10 NS x 3/4 inch |
| 1 | 60-4917T2 | 1 | PLENUM – air conditioner and heater |
| 2 | 60-4698T1 | 1 | DOOR – heat/defrost director |
| 3 | 19-6129 | 2 | BUSHING – split flange, 11/32 ID x 7/16 inch OD, snap in, door pivot |
| 4 | 60-4680T1 | 1 | ROD – pivot, plenum door |
| 5 | 19-5758 | 2 | NUT – push on type |
| 6 | 19-157 | 5 | RIVET – pop, 1/8 x 3/8 inch |
| 7 | 495-31016 | 5 | WASHER – flat, 5/32 x 3/8 x 3/64 inch |
| 8 | 60-4976T1 | 1 | BRACKET – clamp mounting |
| 9 | 515-2663 | 1 | CLAMP – P-type, 1/4 inch ID, cable retaining |
| 10 | 463-41012 | 2 | SCREW – machine, hex slotted washer head, No. 10 NC x 3/4 inch |
| 11 | 280-13512 | 8 | SCREW – self-tapping, hex washer head, No. 10-16 x 3/4 inch |
| 12 | 495-31022 | 16 | WASHER, #10 |
| 13 | 86632551 | 10 | NUT, LOCK, #10-24, GB |
| 14 | 60-4681T1 | 1 | SEAL – adhesive-backed, 432 mm (17 inch) long, cut from 2-7261T1 bulk seal, see below, plenum door |
| 15 | 1975905C1 | 8 | NUT – special, U-speed, No. 10-16 |
| 18 | 19-6046 | 2 | WASHER – flat, 5/16 x 5/8 x 1/8 inch |
| 19 | 60-6715T1 | 2 | LEVER – cable actuating |
| 20 | 19-5995 | 2 | WASHER – spring, 5/16 inch |
| 21 | 231-2445 | 2 | NUT – hex, self-locking, 5/16 inch NF |
| 22 | 60-6713T2 | 1 | PANEL – climate control |
| 23 | 60-6716T1 | 1 | DECAL – climate control panel |
| 24 | 280-13410 | 4 | SCREW – self-tapping, hex washer head, No. 8-18 x 5/8 inch |
| 26 | 92101C1 | 1 | SWITCH – thermostat |
| 27 | 92100C2 | 1 | SWITCH – blower motor |
| 29 | 495-11028 | 3 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 30 | 425-104 | 3 | NUT – hex, 1/4 inch NC |
| 32 | 60-4543T1 | 1 | CABLE – heater/defroster/air conditioning |
| 33 | 60-6718T1 | 1 | CABLE – actuating, water valve |
| 34 | 425-115 | 2 | NUT – hex, 5/16 inch NF |
| 35 | 19-6229 | 1 | STUD – lever |
| 36 | 60-6717T1 | 2 | KNOB – control, lever |
| 37 | 60-3958T1 | 2 | KNOB – control, lower rate |
| 38 | 1954626C1 | 1 | CLIP – retaining, heater cable |
| 1 | 301803R1 | 1 | VALVE – shutoff, water |
| 2 | 221-89 | 1 | REDUCER – pipe, 1/2 male x 3/8 inch female |
| 3 | 32-333 | 1 | HOSE – 787 mm (31 inch) long, cut from 97252CX bulk hose, see below |
| 4 | 214-1408 | 4 | CLAMP – adj, 1/2 – 29/32 inch dia, hose |
| 5 | 31-2937 | 1 | HOSE – 2438 mm (96 inch) long, cut from 32-50 bulk hose, see below |
| 6 | 495-11034 | 1 | WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 7 | 515-23381 | 1 | CLAMP, 1 1/2″, Insul, 3/8″ Bolt, P-type |
| 8 | 217-134 | 1 | ELBOW – 90 degree, 5/8 stem end x 1/2 inch PT |
| 9 | 515-25238 | 1 | CLAMP – P-type, 15/16 inch ID |
| 10 | 426-816 | 2 | BOLT – hex, 1/2 NC x 1 inch, grade 8 |
| 11 | 1-2191 | 1 | CLAMP – P-type |
| 13 | 90-6830T1 | 1 | TUBE – heater |
| 14 | 426-512 | 3 | BOLT – hex, 5/16 NC x 3/4 inch, grade 8 |
| 15 | 231-1445 | 3 | NUT – hex, self-locking, 5/16 inch NC |
| 16 | 31-2283 | 1 | HOSE – 2591 mm (102 inch) long, cut from 32-50 bulk hose, prior to P.I.N. JEE0036501, see below |
| 17 | 214-1420 | 2 | CLAMP – adj, 13/16 – 1-3/4 inch dia |
| 18 | 19-135 | 1 | STRAP – tie, nylon |
| 19 | 221-89 | 1 | REDUCER – pipe, 1/2 male x 3/8 inch female, P.I.N. JEE0036501 and after |
| 20 | 221-338 | 1 | COUPLING – pipe, 1/2 inch, P.I.N. JEE0036501 and after |
| 21 | 217-1072 | 1 | NIPPLE – hex, 1/2 PT x 1-7/8 inch, P.I.N. JEE0036501 and after |
| 22 | 90-8315T1 | 1 | TUBE – precleaner, used on 9390 |
| 1 | 60-6711T1 | 1 | CONDENSER – air conditioning |
| 2 | 1990758C2 | 1 | RECEIVER-DRIER – air conditioning |
| 3 | 70-6589T1 | 2 | BRACKET – mounting |
| 4 | 60-6953T1 | 1 | HOSE – 2006 mm (78 inch) long, receiver-drier to expansion valve, Includes: Ref. 5 |
| 5 | 128483A1 | 2 | O-RING – 5/16 ID x 1/16 inch wide |
| 6 | 60-6952T1 | 1 | HOSE – 2794 mm (110 inch) long, condenser to receiver-drier, Includes: Ref. 7 |
| 7 | 128483A1 | 2 | O-RING – 5/16 ID x 1/16 inch wide |
| 8 | 60-6951T1 | 1 | HOSE – 3683 mm (145 inch) long, discharge, compressor to condenser, Includes: Ref. 9 & 10 |
| 9 | 128485A1 | 1 | O-RING – 9/16 ID x 1/16 inch wide |
| 10 | 128484A1 | 1 | O-RING – 7/16 ID x 1/16 inch wide |
| 11 | 60-6954T1 | 1 | HOSE – 2007 mm (79 inch) long, Includes: Ref. 12 |
| 12 | 128485A1 | 2 | O-RING – 9/16 ID x 1/16 inch wide |
| 13 | 1990756C2 | 1 | VALVE – expansion |
| 14 | 232948A1 | 1 | SWITCH – high pressure, 400 psi, replaces 1999925C1 switch |
| 15 | 122579A1 | 1 | SWITCH – low pressure |
| 16 | 128485A1 | 1 | O-RING – 9/16 ID x 1/16 inch wide |
| 17 | 128484A1 | 1 | O-RING – 7/16 ID x 1/16 inch wide |
| 18 | 515-23270 | 1 | CLAMP – P-type, 1-1/16 inch ID |
| 19 | 515-23190 | 1 | CLAMP – P-type, 3/4 inch ID |
| 20 | 22-824 | 3 | STRAP – tie, 7 inch |
| 21 | 50-2551T1 | 1 | CLAMP – hose, split, includes both halves |
| 22 | 425-106 | 6 | NUT, 3/8″-16, G5 |
| 23 | 426-524 | 3 | BOLT – hex, 5/16 NC x 1-1/2 inch, grade 8 |
| 24 | 426-516 | 3 | BOLT – hex, 5/16 NC x 1 inch, grade 8 |
| 25 | 396-41034 | 10 | WASHER – flat, 11/32 x 1 x 3/32 inch, hardened |
| 26 | 426-58 | 6 | BOLT – hex, 5/16 NC x 1/2 inch, grade 8 |
| 27 | 60-5816T1 | 1 | BRACKET – mounting, clamp |
| 28 | 231-1445 | 5 | NUT – hex, self-locking, 5/16 inch NC |
| 29 | 426-512 | 1 | BOLT – hex, 5/16 NC x 3/4 inch, grade 8 |
| 1 | 1999755C2 | 1 | COMPRESSOR ASSEMBLY – air conditioning, parts list Figure 9-106 |
| 2 | 90-8440T1 | 1 | MOUNT – compressor, replaces 90-7735T1 mount |
| 3 | 426-820 | 2 | BOLT – hex, 1/2 NC x 1-1/4 inch, grade 8 |
| 4 | 496-11053 | 2 | WASHER, 17/32″ x 1 1/16″ x .095″, HDN |
| 5 | 426-612 | 2 | BOLT – hex, 3/8 NC x 3/4 inch, grade 8 |
| 7 | 614-10035 | 4 | BOLT – hex, full threads, 10 – 1.5 x 35 mm |
| 8 | 496-21041 | 4 | WASHER – flat, 13/32 x 13/16 x 3/32 inch, hardened |
| 9 | 825-1410 | 4 | Nut, M10, Cl 8 |
| 12 | 496-41041 | 3 | WASHER – flat, 13/32 x 1-1/8 x 9/64 inch, hardened |
| 13 | 90-6871T2 | 1 | BRACKET – mounting, shield |
| 14 | 90-6872T1 | 1 | SHIELD – compressor |
| 15 | 413-1016 | 1 | BOLT – hex, 5/8 NC x 1 inch |
| 16 | 426-512 | 2 | BOLT – hex, 5/16 NC x 3/4 inch, grade 8 |
| 17 | 495-21038 | 2 | WASHER – flat, 3/8 x 7/8 x 3/32 inch |
| 18 | 231-1445 | 2 | NUT – hex, self-locking, 5/16 inch NC |
| 22 | 90-7190T1 | 1 | BELT – V, compressor |
| 1 | 1999755C2 | 1 | COMPRESSOR ASSEMBLY – air conditioning, Includes: Ref. 2 – 4 |
| 2 | 135324A1 | 1 | CLUTCH ASSEMBLY – compressor |
| 3 | A49667 | 1 | PLUG – hex |
| 4 | 128483A1 | 1 | O-RING – 5/16 ID x 1/16 inch wide |
| 5 | 60-3091T1 | 1 | KIT – seal, compressor, replaced by A49665 kit |
| 5 | A49665 | 1 | KIT – seal, compressor, replaces 60-3091T1 kit |
| 1 | 70-6747T1 | 1 | PANEL – top |
| 2 | 70-6745T1 | 1 | BRACKET – mounting, not shown, not used in this application |
| 3 | 70-6748T1 | 1 | HINGE – tool box |
| 4 | 426-828 | 2 | BOLT – hex, 1/2 NC x 1-3/4 inch, grade 8 |
| 5 | 426-820 | 2 | BOLT – hex, 1/2 NC x 1-1/4 inch, grade 8, not shown, not used in this application |
| 6 | 426-48 | 7 | BOLT – hex, 1/4 NC x 1/2 inch, grade 8 |
| 7 | 425-104 | 7 | NUT – hex, 1/4 inch NC |
| 8 | 425-108 | 2 | NUT – hex, 1/2 inch NC |
| 9 | 70-6752T1 | 1 | BOX – storage |
| 1 | 70-6657T2 | 1 | BRACKET – front weights |
| 2 | 426-1232 | 9 | BOLT – hex, 3/4 NC x 2 inch, grade 8 |
| 3 | 496-81000 | 18 | WASHER – flat, 25/32 x 1-3/8 x 1/8 inch, hardened |
| 4 | 425-1012 | 9 | NUT – hex, 3/4 inch NC |
| 5 | 1978431C1 | 16 | CLAMP – weights |
| 6 | 495-11053 | 16 | WASHER, 1/2″, SAE (17/32″ x 1-1/16″ x 3/32″) |
| 7 | 80679 | 16 | Washer, Lock, 1/2″ |
| 8 | 425-108 | 16 | NUT – hex, 1/2 inch NC |
| 9 | A169139 | 16 | BOLT – square head, special, 1/2 NC x 3-1/4 inch |
| 10 | 1347524C1 | 30 | WEIGHT – front, order 1348233C1 or A67894 weight from Machinery Price List, 45.36 kgs, (100 pound) |
| 1 | 70-6674T1 | 1 | BRACKET – rear weights, lower |
| 2 | 426-1232 | 6 | BOLT – hex, 3/4 NC x 2 inch, grade 8 |
| 3 | 496-81000 | 16 | WASHER – flat, 25/32 x 1-3/8 x 1/8 inch, hardened |
| 4 | 425-1012 | 6 | NUT – hex, 3/4 inch NC |
| 5 | 1978431C1 | 13 | CLAMP – weights |
| 6 | 80679 | 13 | Washer, Lock, 1/2″ |
| 7 | 495-11053 | 13 | WASHER, 1/2″, SAE (17/32″ x 1-1/16″ x 3/32″) |
| 8 | 425-108 | 13 | NUT – hex, 1/2 inch NC |
| 9 | A169139 | 13 | BOLT – square head, special, 1/2 NC x 3-1/4 inch |
| 10 | 1347524C1 | 24 | WEIGHT – front, order 1348233C1 or A67894 weight from Machinery Price List, 45.36 kgs, (100 pound) |
| 11 | 70-6686T1 | 2 | BRACKET – rear weights, upper |
| 12 | 426-1232 | 8 | BOLT – hex, 3/4 NC x 2 inch, grade 8 |
| 13 | 496-81000 | 16 | WASHER – flat, 25/32 x 1-3/8 x 1/8 inch, hardened |
| 14 | 425-1012 | 86 | NUT – hex, 3/4 inch NC |
| 15 | 1978431C1 | 10 | CLAMP – weights |
| 16 | 80679 | 10 | Washer, Lock, 1/2″ |
| 17 | 495-11053 | 10 | WASHER, 1/2″, SAE (17/32″ x 1-1/16″ x 3/32″) |
| 18 | 425-108 | 10 | NUT – hex, 1/2 inch NC |
| 19 | A169139 | 10 | BOLT – square head, special, 1/2 NC x 3-1/4 inch |
| 20 | 1347524C1 | 18 | WEIGHT – front, order 1348233C1 or A67894 weight from Machinery Price List, 45.36 kgs, (100 pound) |
| 1 | 60-7036T1 | 2 | DECAL – three point hitch switch |
| 3 | 1968108C2 | 1 | TRIM – hood sight |
| 4 | 321-4311 | 1 | DECAL – SMV emblem, used on plastic surfaces only |
| 4 | 407263R1 | 1 | DECAL – SMV emblem, used on painted surfaces only |
| 4 | 202013C2 | 1 | EMBLEM – slow moving vehicle, replaces 26-1 decal and is replaced by 311860A1 emblem |
| 4 | 311860A1 | 1 | EMBLEM – slow moving vehicle, replaces 202013C2 emblem |
| 5 | 2-6876T3 | 1 | DECAL – Warning, no clearance for person when tractor turns |
| 6 | 60-7285T1 | 1 | DECAL – instrument cluster, Power Shift |
| 7 | 139879A1 | 1 | DECAL – diesel fuel |
| 8 | 2-6874T2 | 1 | DECAL – center hinge locking bar |
| 9 | 2-7125T2 | 1 | DECAL – Warning, rotating driveline |
| 10 | 60-7286T1 | 1 | DECAL – instrument cluster, SynchroShift |
| 12 | 2-6935T2 | 1 | DECAL – Warning, lifting data, NEW TEMPORARY DECAL THAT COMBINES LIFTING INSTR. |
| 13 | 426-412 | 2 | BOLT – hex, 1/4 NC x 3/4 inch, grade 8, not shown |
| 14 | 425-104 | 2 | NUT – hex, 1/4 inch NC, not shown |
| 15 | 495-11028 | 2 | WASHER – flat, 9/32 x 5/8 x 1/16 inch, not shown |
| 21 | A189007 | 1 | DECAL – warranty, fuel pump |
| 1 | 60-6416T1 | 1 | DECAL – control console, Power Shift tractor |
| 2 | 60-7065T1 | 1 | DECAL – control console, SynchroShift tractor |
| 3 | 60-5939T2 | 1 | DECAL – gauge panel, prior to P.I.N. JEE0071001 |
| 4 | 60-7064T1 | 1 | DECAL – overhead relay |
| 5 | 60-5980T1 | 1 | DECAL – master lamps, ROPS |
| 6 | 60-5866T1 | 1 | DECAL – Caution, when operating this vehicle use hearing protection |
| 7 | 60-6468T2 | 1 | DECAL – Warning, avoid injury or death |
| 8 | 60-5939T3 | 1 | DECAL – gauge panel, P.I.N. JEE0071001 and after |
| 9 | 2-6879T1 | 1 | DECAL – emergency exit |
| 10 | 60-6297T1 | 1 | DECAL – circuit breaker |
| 11 | 60-7158T1 | 1 | DECAL – relay |
| 12 | 60-7153T1 | 1 | DECAL – overhead controls |
| 13 | 60-6716T1 | 1 | DECAL – climate control panel |
| 1 | 60-7143T1 | 1 | DECAL – 9370 Case International, left-hand |
| 2 | 60-7144T1 | 1 | DECAL – 9370 Case International, right-hand |
| 3 | 60-7145T1 | 1 | DECAL – 9380 Case International, left-hand |
| 4 | 60-7146T1 | 1 | DECAL – 9380 Case International, right-hand |
| 5 | 60-7147T1 | 1 | DECAL – cab, left-hand side |
| 6 | 60-7149T1 | 1 | DECAL – cab, right-hand side |
| 7 | 60-7148T1 | 1 | DECAL – cab, rear |
| 8 | 60-7224T1 | 1 | DECAL – 9390 Case International, left-hand |
| 9 | 60-7223T1 | 1 | DECAL – 9390 Case International, right-hand |
| 1 | 60-6723T1 | 1 | DECAL – MPH, 24 speed SynchroShift |
| 2 | 60-6567T2 | 1 | DECAL – MPH, 12 speed SynchroShift |
| 3 | 60-6568T1 | 1 | DECAL – gear/mile per hour, Power Shift |
| 7 | 60-7097T1 | 1 | DECAL – Steiger, if used |
| 13 | 2-4585T2 | 1 | EMBLEM – Steiger, grille |
| 14 | 495-11028 | 4 | WASHER – flat, 9/32 x 5/8 x 1/16 inch |
| 15 | 9420182 | 4 | NUT – special |
| 16 | 70-6772T1 | 1 | BRACKET – emblem |
| 17 | 281-18712 | 4 | SCREW – self-tapping, hex washer head, 1/4 NC x 3/4 inch |
| 18 | 131-610 | 2 | NUT – U-type, 1/4 inch NC |