CASE IH 4WD tractor 9370, 9380, 9390

      No Comments on CASE IH 4WD tractor 9370, 9380, 9390

CASE IH 4WD tractor 9370, 9380, 9390 — parts list, part 2 of 4

Assemblies on this page: Parts list (continued) … Parts list (continued).

Parts list (continued)

Pos Part no. Qty Description
19 S4040S00F 2 SPACER – bearing
20 54404R1 2 CUP – tapered roller bearing
21 ST2016A 2 BEARING – tapered roller
22 S2030S00F 2 BEARING – roller
23 S4170S00F 1 GEAR – output, 59 teeth
24 S4160S00F 1 CARRIER – piston ring
25 S4150S00F 4 RING – sealing, Part of transmission rebuild gasket kit P/N 33-1559T2.
26 S4530S02F 2 PLATE – retaining, spring
1 S5900S00F 1 SHAFT – drum
2 S5520S00F 2 RING – piston, Part of transmission rebuild gasket kit P/N 33-1559T2.
3 S5510S00F 2 RING – piston, Part of transmission rebuild gasket kit P/N 33-1559T2.
4 S4430S00F 2 RING – sealing, Part of transmission rebuild gasket kit P/N 33-1559T2.
5 33-1523T1 1 PISTON – clutch
6 33-1522T1 1 PISTON – clutch
8 33-1520T2 12 PLATE – faced
9 S5550S00F 8 SPRING – return, piston
10 S5850S01G 1 HUB – clutch
11 S5100S00F 2 RING – snap
12 S5540S00F 8 SPRING – return, piston
13 S5490S00F 1 RING – retaining
14 S5840S01G 1 HUB – clutch
15 S5230S00F 8 WASHER – thrust
16 A75158 4 BEARING – thrust, replaces S5050S00F bearing
17 S5070S00F 2 BEARING – needle
18 S5080S01F 1 GEAR – clutch, 37 teeth
19 S5040S00F 2 RING – retaining
20 S3070S00F 4 RING – sealing, Part of transmission rebuild gasket kit P/N 33-1559T2.
21 S5060S01F 1 GEAR – input, 43 teeth
22 54404R1 1 CUP – tapered roller bearing
23 ST2016A 1 BEARING – tapered roller
24 S5270S00F 1 GEAR – drive, 21 teeth
25 90-6579T1 1 CUP – tapered roller bearing
26 ST2018A 1 CONE – tapered roller bearing
27 S5280S01F 1 GEAR – clutch, 46 teeth
28 SM9222160 2 RING – snap
31 S3210S00F 2 SPRING – valve
32 S3200S00F 2 VALVE – drain
1 S6090S00F 1 COVER – control stem
2 STX99700F 3 PLUG – stem cover port
3 S6120S00F 1 O-RING – control stem, Part of transmission rebuild gasket kit P/N 33-1559T2.
4 S6110S00F 1 SEAL – control stem, Part of transmission rebuild gasket kit P/N 33-1559T2.
5 S6100S00F 1 STEM – control
6 S6080S00F 1 LINK – connecting
7 90-8199T1 1 SPRING – tension
8 S6130S00F 1 PIN – roll
9 S6200S00F 1 SPACER – 31 x 1.2 mm thick
11 S6150S00F 1 SPRING – compression
12 S6060S00F 1 SEAT – spring
13 S6070S00F 1 GASKET – control stem cover, Part of transmission rebuild gasket kit P/N 33-1559T2.
14 S6050S00F 1 BODY – modulator
15 S6240S00F 1 PLUG – orifice
16 S6230S00F 2 PLUG – orifice
17 S6260S00F 8 BOLT – socket head, special
18 S6160S00F 1 POPPET – spool
19 S6040S00F 1 SPOOL – modulator
20 S6030S00F 1 GASKET – valve cover, Part of transmission rebuild gasket kit P/N 33-1559T2.
21 S6020S00F 1 COVER – valve
22 S6010S00F 1 SPOOL – reducing
23 S6180S00F 1 O-RING – plug, Part of transmission rebuild gasket kit P/N 33-1559T2.
24 S6170S00F 1 PLUG – hex, valve cover
25 S6220S00F 6 PLUG – valve cover
2 S7030S01F 1 VALVE – regulator
3 S7020S00F 1 ROD – pressure
5 S7120S00F 1 SPRING – compression
6 S7050S00F 2 SPRING – compression
8 S7060S00F 2 VALVE – lube
9 S7070S00F 1 SPRING – compression
10 S7090S00F 1 GASKET – valve cover, Part of transmission rebuild gasket kit P/N 33-1559T2.
11 S7110S00F 1 COVER – valve body
12 SM8120820 5 BOLT – hex, 8 – 1.25 x 20 mm
13 S1030S00F 2 PLUG – hex, O-ring boss, Includes: Ref. 14
14 S1040S00F 2 O-RING – plug
1 33-1540T1 3 BOLT – hex, pump adapter
2 33-1541T1 1 ADAPTER – pump mounting
3 33-1542T1 1 O-RING – seal, Part of lubrication pump O-ring kit P/N 90-8261T91.
4 33-1543T1 1 RING – locating
5 33-1544T1 4 BOLT – hex, housing
6 33-1545T1 4 BOLT – hex, housing
7 33-1546T1 1 HOUSING – front, Includes: Ref. 8
10 33-1547T1 2 O-RING – pump housing, Part of lubrication pump O-ring kit P/N 90-8261T91.
11 33-1548T1 4 PIN – dowel
19 33-1549T1 1 HOUSING – center
20 33-1550T1 4 RING – snap
21 33-1551T1 1 SHAFT – drive
22 33-1552T1 1 SHAFT – idler
23 33-1553T1 1 KEY – dowel, idler shaft
24 33-1554T1 1 KEY – dowel, drive shaft
25 33-1555T1 2 GEAR – pump
26 33-1556T1 1 HOUSING – rear, Includes: Ref. 27
30 33-1557T1 1 TUBE – inlet
1 33-1529T1 1 BODY – valve, range selector
2 33-1530T1 1 GASKET – valve cover
3 33-1531T1 1 COVER – body
4 S1030S00F 1 PLUG – hex, O-ring boss, Includes: Ref. 5
5 S1040S00F 1 O-RING – plug
6 S1390S00F 1 PLUG – O-ring boss, Includes: Ref. 7
7 S1320S00F 1 O-RING – plug
8 426-512 10 BOLT – hex, 5/16 NC x 3/4 inch, grade 8
9 33-1532T1 8 SPRING – spool
10 33-1533T1 8 SPOOL – valve selector
11 33-1534T1 8 RING – snap
27 33-1537T1 8 O-RING – seal, filter
28 33-1538T1 8 FILTER – conical
29 33-1539T1 8 PLUG – filter
31 50-3322T2 1 COVER – protective, transmission solenoids
1 33-1410T1 1 YOKE – input
2 33-1414T1 1 O-RING – yoke sealing, Part of transmission gasket kit P/N 90-8401T91.
4 33-1413T1 1 PLATE – yoke retainer
5 514-730 3 BOLT – hex, 10 – 1.25 x 35 mm
7 90-7991T1 1 GASKET – bearing retainer, Part of transmission gasket kit P/N 90-8401T91.
8 90-7992T1 1 RETAINER – bearing, pump drive shaft
9 514-832 6 BOLT – hex, 12 – 1.25 x 35 mm
10 90-7993T1 1 GASKET – bearing retainer, input shaft, Part of transmission gasket kit P/N 90-8401T91.
11 90-7994T1 1 RETAINER – bearing, input shaft
12 514-721 12 BOLT – hex, 10 – 1.25 x 30 mm
13 33-1636T1 1 WASHER – retrainer, seal
14 33-1412T1 1 SEAL – input yoke, Part of transmission gasket kit P/N 90-8401T91.
15 S1030S00F 4 PLUG – hex, O-ring boss, Includes: Ref. 16
16 S1040S00F 4 O-RING – plug, Part of transmission gasket kit P/N 90-8401T91.
17 90-7995T1 1 PLATE – retainer cover
18 514-720 5 BOLT – hex, 10 – 1.25 x 50 mm
19 90-7996T1 1 GASKET – cover plate, Part of transmission gasket kit P/N 90-8401T91.
20 90-7997T1 1 RETAINER – bearing, third shaft
21 90-7998T1 1 GASKET – bearing retainer, third shaft, Part of transmission gasket kit P/N 90-8401T91.
22 90-7999T1 1 GASKET – ditch plate, Part of transmission gasket kit P/N 90-8401T91.
23 33-1620T1 1 O-RING – retainer, Part of transmission gasket kit P/N 90-8401T91.
24 S1210S00F 1 PLUG – hex, O-ring boss
25 S1200S00F 1 O-RING – plug, Part of transmission gasket kit P/N 90-8401T91.
26 514-718 5 BOLT – hex, 10 – 1.25 x 40 mm
27 90-8000T1 1 PLATE – ditch
28 90-8001T1 1 RETAINER – bearing, fourth shaft
29 614-8016 2 BOLT – hex, full threads, 8 – 1.25 x 16 mm
31 514-832 6 BOLT – hex, 12 – 1.25 x 35 mm
32 33-1432T1 2 PLATE – retainer
33 33-1422T1 2 O-RING – yoke sealing, Part of transmission gasket kit P/N 90-8401T91.
34 33-1429T1 1 YOKE – output
35 33-1428T1 2 SEAL – output shaft, Part of transmission gasket kit P/N 90-8401T91.
36 90-8002T1 1 RETAINER – bearing, fifth shaft
37 90-8003T1 1 GASKET – bearing retainer, fifth shaft, Part of transmission gasket kit P/N 90-8401T91.
38 90-8004T1 1 YOKE – output, rear, 8C
39 90-7987T1 1 HOUSING – rear, transmission
40 S1080S00F 4 O-RING – plug, Part of transmission gasket kit P/N 90-8401T91.
41 S1090S00F 1 PLUG – magnetic
42 S1010S00F 3 PLUG – O-ring boss
43 514-841 2 BOLT – hex, 12 – 1.25 x 20 mm
44 514-834 6 BOLT – hex, 12 – 1.25 x 30 mm
45 33-1619T2 1 COVER – end, used on models without PTO
46 514-738 1 BOLT – hex, 10 – 1.25 x 45 mm
1 218-5140 1 ELBOW – 45 degree, 1-5/16-12 inch flare x adj O-ring boss
2 33-1874T91 1 PUMP – lubrication, component parts not serviced separately, Part of lubrication pump O-ring kit P/N
3 31-1394 1 ELBOW – hose stem, special
4 514-721 2 BOLT – hex, 10 – 1.25 x 30 mm
5 90-8007T1 2 BOLT – socket head, special
6 90-8008T1 2 BOLT – socket head, special
7 90-8009T91 1 VALVE ASSEMBLY – lock out, parts list Figure 6-064
8 514-729 2 BOLT – hex, 10 – 1.25 x 90 mm, class 8.8
9 514-739 2 BOLT – hex, 10 – 1.25 x 120 mm, class 8.8
10 90-8200T91 1 VALVE ASSEMBLY – control, parts list Figure 6-062
11 90-8012T1 1 GASKET – control valve, Part of transmission gasket kit P/N 90-8401T91.
12 614-8065 5 BOLT – hex, full threads, 8 – 1.25 x 65 mm
13 614-8100 3 BOLT – hex, full threads, 8 – 1.25 x 100 mm
14 S7000S01F 1 VALVE ASSEMBLY – regulator, parts list Figure 6-060
15 S1150S02F 1 GASKET – regulator valve, Part of transmission gasket kit P/N 90-8401T91.
16 S14701960 1 BALL – steel
17 33-1561T1 1 TUBE – suction
18 S1620S01F 1 GASKET – suction tube, Part of transmission gasket kit P/N 90-8401T91.
19 S1700S00F 1 PLATE – suction tube retainer
1 614-6012 2 BOLT, Hex, M6 x 12, 8.8
2 90-7982T1 1 BAFFLE – breather
3 90-7983T1 1 LEVER – shift, second and third speed, inner
4 90-7984T1 1 LEVER – shift, C and D range, inner
5 33-1761T1 1 PLUG – taper
6 33-1454T1 1 FILTER – breather
7 33-1455T1 1 ELBOW – 90 degree, breather filter
8 SM8911246 1 NUT – hex, 16 mm – 1.5
9 90-7985T1 2 HOLDER – lever
10 514-712 4 BOLT – hex, 10 – 1.25 x 25 mm
11 33-1727T1 2 SEAL – holder, Part of transmission gasket kit P/N 90-8401T91.
12 90-7975T1 1 LEVER – shift, speed, outer
13 SM831050 2 PIN – spring
14 90-7977T1 1 LEVER – shift, range, outer
15 90-8006T1 1 GASKET – breather, Part of transmission gasket kit P/N 90-8401T91.
1 33-1767T1 7 BOLT – socket head, special
2 33-1807T1 2 PIN – dowel
3 90-8157T1 1 SHAFT – idler, reverse
4 90-7953T1 2 BEARING – tapered roller
5 90-7954T1 1 GEAR – idler, reverse
7 33-1693T1 1 PLATE – retainer
8 514-1021 1 Bolt, Hex, M16 x 1.5 x 35, 10.9, Full Thd
9 614-6012 7 BOLT, Hex, M6 x 12, 8.8
10 90-7955T1 1 GUTTER – input
11 514-832 12 BOLT – hex, 12 – 1.25 x 35 mm
12 90-7957T1 1 PLATE – support
13 90-7958T1 1 COVER – idler shaft
14 514-730 3 BOLT – hex, 10 – 1.25 x 35 mm
15 90-7959T1 1 GUTTER – bearing
16 90-7960T1 1 GUTTER – gear, second speed
17 90-7961T1 1 GUTTER – gear, first speed
18 90-7962T1 1 PIN – roll
20 90-7920T1 2 BEARING – tapered roller
21 90-7968T1 1 GEAR – idler
22 90-7969T1 1 SHAFT – idler
23 90-7970T1 1 O-RING – shaft, Part of transmission gasket kit P/N 90-8401T91.
24 90-7971T1 1 LEVER – shift, first-reverse speed, inner
25 90-7972T1 1 LEVER – shift, A-B range, inner
26 90-7973T1 2 PIN – dowel
27 90-7974T1 1 HOLDER – lever, first-reverse speed
28 514-712 4 BOLT – hex, 10 – 1.25 x 25 mm
29 33-1727T1 2 SEAL – holder, Part of transmission gasket kit P/N 90-8401T91.
30 90-7975T1 1 LEVER – shift, speed, outer
31 SM831050 3 PIN – spring
32 90-7976T1 1 HOLDER – lever, A-B range
33 90-7977T1 1 LEVER – shift, range, outer
34 90-7978T1 1 PAN – oil
35 514-703 2 BOLT – hex, 10 – 1.25 x 20 mm
37 514-842 2 BOLT – hex, 12 – 1.25 x 25 mm
38 825-11410 2 NUT – hex, 10 mm – 1.25
39 90-7979T1 1 BRACKET – oil pan, left-hand
40 90-7980T1 1 BRACKET – oil pan, right-hand
41 90-7987T1 1 HOUSING – rear, transmission
42 90-7948T1 12 WASHER – wave
36 895-11010 2 WASHER – flat, 11 x 20 x 2 mm
1 514-843 13 BOLT – hex, 12 – 1.25 x 60 mm
2 33-1467T1 2 PIN – dowel
3 90-7943T91 1 SHAFT ASSEMBLY – input, 12 speed, parts list Figure 6-058
4 90-7986T91 1 SHAFT ASSEMBLY – fourth, parts list Figure 6-056
5 90-7987T1 1 HOUSING – rear, transmission
6 90-7988T91 1 SHAFT ASSEMBLY – third, parts list Figure 6-052
7 514-703 2 BOLT – hex, 10 – 1.25 x 20 mm
8 33-1746T1 1 PLATE – lock
9 90-7989T1 1 HOUSING – front, transmission
10 514-830 16 BOLT – hex, 12 – 1.25 x 40 mm
11 90-7990T91 1 SHAFT ASSEMBLY – fifth, parts list Figure 6-054
12 33-1812T1 1 LIP – oil, reverse gear
13 614-6012 2 BOLT, Hex, M6 x 12, 8.8
1 529208R1 1 CUP – tapered roller bearing
1 529207R91 1 CONE – tapered roller bearing
2 90-7939T1 1 COUPLING – sleeve, pump
3 33-1416T1 2 RING – retaining
4 90-7940T1 1 GEAR – driven, pump drive shaft
5 90-7941T1 1 PIN – dowel
6 90-7942T1 1 SHAFT – pump drive
7 90-7937T1 1 CONE – tapered roller bearing
1 90-7944T1 1 FORK – shift, first-reverse
2 33-1757T1 4 BALL – steel, fork detent
3 33-1786T1 4 SPRING – detent ball
4 33-1759T1 4 PLUG – detent spring
5 90-7945T1 1 ROD – shift, speed
6 90-7946T1 1 PLATE – interlock
7 90-7947T1 2 PIN – spring
8 33-1756T1 2 BALL – steel
9 33-1745T1 2 O-RING – seal, fork, Part of transmission gasket kit P/N 90-8401T91.
10 90-7949T1 1 FORK – shift, second-third speeds
11 90-7950T1 1 FORK – shift, C-D ranges
12 90-7951T1 1 FORK – shift, A-B ranges
13 90-7952T1 1 ROD – shift, range
2 33-1708T1 1 BEARING – tapered roller
3 90-7893T1 1 GEAR – driven, third shaft
4 S5040S00F 2 RING – retaining
5 90-7894T1 1 GEAR – drive, first speed
6 90-7895T1 4 DISK – synchro, speed
7 90-7904T1 4 RING – retaining
8 SM832508 16 PIN – spring
9 90-7896T1 1 RING – retaining
10 S5070S00F 1 BEARING – needle
11 33-1830T1 2 SYNCHRONIZER – speed
12 S5090S00F 4 RING – retaining
13 90-8013T1 1 RING – retaining
14 90-7897T1 1 GEAR – drive, reverse speed
15 90-8014T1 1 RING – retaining
16 90-8015T1 1 BEARING – needle
17 90-7898T1 1 SHAFT – speed
18 90-7899T1 1 GEAR – drive, second speed
19 90-7900T1 1 GEAR – drive, third speed
20 90-7901T1 1 SPACER – third speed gear
21 33-1676T1 1 BEARING – tapered roller
1 33-1708T1 1 BEARING – tapered roller
2 S5230S00F 2 WASHER – thrust
3 A75158 1 BEARING – thrust, replaces S5050S00F bearing
4 S5070S00F 2 BEARING – needle
5 90-7902T1 1 GEAR – driven, A range
6 90-7903T1 4 DISK – synchro, range
7 90-7904T1 4 RING – retaining
8 SM832508 16 PIN – spring
9 33-1831T1 2 SYNCHRONIZER – range
10 S5090S00F 4 RING – retaining
11 90-7905T1 1 GEAR – driven, B range
12 90-7906T1 1 SHAFT – output
13 90-7907T1 1 GEAR – driven, C range
14 90-7908T1 1 GEAR – driven, D range
15 33-1676T1 1 BEARING – tapered roller, shaft
16 S4150S00F 2 RING – sealing, Part of transmission gasket kit P/N 90-8401T91.
17 33-1695T1 1 PISTON – carrier, ring
2 33-1676T1 2 BEARING – tapered roller, shaft
3 90-7909T1 1 GEAR – drive, A range
4 90-7910T1 1 GEAR – driven, first speed
5 90-7911T1 1 SHAFT – center, fourth
6 90-7912T1 1 GEAR – drive, B range
7 90-7913T1 1 GEAR – driven, second speed
8 S5090S00F 1 RING – retaining
9 S5040S00F 1 RING – retaining
10 90-7914T1 1 GEAR – driven, third speed
11 90-7915T1 1 GEAR – driven, D range
2 90-7920T1 1 BEARING – tapered roller
3 90-7921T1 2 WASHER – thrust
4 90-7922T1 1 BEARING – thrust
5 90-7923T1 1 COLLAR – bearing
6 90-7924T1 1 GEAR – drive, input
7 33-1829T1 1 RING – retaining
8 S5070S00F 2 BEARING – needle
9 S5040S00F 5 RING – retaining
10 S5230S00F 1 WASHER – thrust
11 A75158 1 BEARING – thrust, replaces S5050S00F bearing
12 90-7925T1 2 WASHER – thrust
13 S14701960 1 BALL – steel
14 90-7926T1 1 SHAFT – input
15 514-721 14 BOLT – hex, 10 – 1.25 x 30 mm
19 90-7930T1 1 COVER – clutch
21 33-1663T1 8 PLATE – clutch, friction
22 33-1785T1 32 PLATE – separating, clutch
23 90-7931T1 2 O-RING – shaft, Part of transmission gasket kit P/N 90-8401T91.
24 90-7932T1 12 SPRING – return
25 90-7933T1 1 PISTON – clutch, prior to P.I.N. JEE0071001
25 90-8389T1 1 PISTON – clutch, P.I.N. JEE0071001 and after
26 33-1662T1 1 RING – seal, large, prior to P.I.N. JEE0071001, Part of transmission gasket kit P/N 90-7927T92
26 90-8385T1 1 RING – seal, P.I.N. JEE0071001 and after, Part of transmission gasket kit P/N 90-8401T91.
27 S2630S00F 1 RING – sealing, prior to P.I.N. JEE0071001, Part of transmission gasket kit P/N 90-7927T92
27 90-8386T1 1 RING – seal, P.I.N. JEE0071001 and after, Part of transmission gasket kit P/N 90-8401T91.
28 90-7934T1 12 PIN – guide, use with 90-7932T1 return spring, Ref. 24
29 33-1659T1 4 PIN – guide, use with 33-1785T1 separating plate, Ref. 22
30 90-7935T1 1 DRUM – clutch, prior to P.I.N. JEE0071001
30 90-8388T1 1 DRUM – clutch, P.I.N. JEE0071001 and after
31 90-7936T1 1 GEAR – drive, pump
32 514-831 16 BOLT – hex, 12 – 1.25 x 45 mm
33 90-7937T1 1 CONE – tapered roller bearing
34 90-7938T1 4 RING – seal
1 S1040S00F 1 O-RING – plug, Part of transmission gasket kit P/N 90-8401T91.
2 S1030S00F 1 PLUG – hex, O-ring boss
3 S7090S00F 1 GASKET – valve cover, Part of transmission gasket kit P/N 90-8401T91.
4 S7110S00F 1 COVER – valve body
5 614-8020 5 BOLT – hex, full threads, 8 – 1.25 x 20 mm
6 S7030S01F 1 VALVE – regulator
8 S7120S00F 1 SPRING – compression
9 S7050S00F 2 SPRING – compression
10 S7020S00F 1 ROD – pressure
11 S7070S00F 1 SPRING – compression
13 S7060S00F 2 VALVE – lube
14 S7000S01F 1 VALVE ASSEMBLY – regulator, replaces S7040S00F body
15 S1320S00F 1 O-RING – plug, Part of transmission gasket kit P/N 90-8401T91.
16 S1390S00F 1 PLUG – O-ring boss
1 S6170S00F 1 PLUG – hex, valve
2 S6180S00F 1 O-RING – plug, Part of transmission gasket kit P/N 90-8401T91.
3 S6260S00F 8 BOLT – socket head, special
4 S6010S00F 1 SPOOL – reducing
5 S6220S00F 11 PLUG – valve
6 S6020S00F 1 COVER – valve
7 S6030S00F 1 GASKET – valve cover, Part of transmission gasket kit P/N 90-8401T91.
8 S6040S00F 1 SPOOL – modulator
9 S6160S00F 1 POPPET – spool, valve
10 S6240S00F 1 PLUG – orifice
11 S6230S00F 2 PLUG – orifice
12 90-8016T1 1 BODY – control valve
13 S6060S00F 1 SEAT – spring
14 90-8199T1 1 SPRING – tension
15 S6080S00F 1 LINK – connecting
16 S6150S00F 1 SPRING – compression
18 S6200S00F 1 SPACER – 31 x 1.2 mm thick
19 S6130S00F 1 PIN – roll
20 S6100S00F 1 STEM – control
21 90-8017T1 1 GASKET – cover, Part of transmission gasket kit P/N 90-8401T91.
22 90-8018T1 1 COVER – control stem
23 S6120S00F 1 O-RING – control stem, Part of transmission gasket kit P/N 90-8401T91.
24 S6110S00F 1 SEAL – control stem, Part of transmission gasket kit P/N 90-8401T91.
1 90-8151T1 1 PLUG – hex cap
2 90-8152T1 2 O-RING – plug, Part of transmission gasket kit P/N 90-8401T91.
3 90-8021T1 1 PLUG – orifice, lock out valve
4 90-8153T1 1 SPOOL – lock out valve
5 90-8154T1 1 SPRING – return
6 90-8019T1 1 BODY – lock out valve
7 90-8155T1 1 PLUG – port
8 90-8020T1 5 O-RING – seal, Part of transmission gasket kit P/N 90-8401T91.
9 90-8156T1 1 PLUG – orifice
1 33-1410T1 1 YOKE – input
2 33-1414T1 1 O-RING – yoke sealing, Part of transmission gasket kit P/N 90-8401T91.
4 90-8256T1 1 PLATE – yoke retainer
5 514-929 3 BOLT – hex, 14 – 1.5 x 35 mm, class 10.9
7 90-7991T1 1 GASKET – bearing retainer, Part of transmission gasket kit P/N 90-8401T91.
8 90-8257T1 1 RETAINER – bearing
9 514-832 6 BOLT – hex, 12 – 1.25 x 35 mm
10 90-7993T1 1 GASKET – bearing retainer, input shaft, Part of transmission gasket kit P/N 90-8401T91.
11 90-8258T1 1 RETAINER – bearing
12 514-721 12 BOLT – hex, 10 – 1.25 x 30 mm
13 33-1636T1 1 WASHER – retrainer, seal
14 33-1412T1 1 SEAL – input yoke, Part of transmission gasket kit P/N 90-8401T91.
15 S1030S00F 7 PLUG – hex, O-ring boss
16 S1040S00F 9 O-RING – plug, Part of transmission gasket kit P/N 90-8401T91.
17 90-7995T1 1 PLATE – retainer cover
18 514-720 5 BOLT – hex, 10 – 1.25 x 50 mm
19 90-7996T1 1 GASKET – cover plate, Part of transmission gasket kit P/N 90-8401T91.
20 90-7997T1 1 RETAINER – bearing, third shaft
21 90-7998T1 1 GASKET – bearing retainer, third shaft, Part of transmission gasket kit P/N 90-8401T91.
22 90-7999T1 1 GASKET – ditch plate, Part of transmission gasket kit P/N 90-8401T91.
23 33-1620T1 1 O-RING – retainer, Part of transmission gasket kit P/N 90-8401T91.
24 S1210S00F 1 PLUG – hex, O-ring boss
25 S1200S00F 1 O-RING – plug, Part of transmission gasket kit P/N 90-8401T91.
26 514-718 5 BOLT – hex, 10 – 1.25 x 40 mm
27 90-8000T1 1 PLATE – ditch
28 90-8001T1 1 RETAINER – bearing, fourth shaft
29 614-8016 2 BOLT – hex, full threads, 8 – 1.25 x 16 mm
31 514-832 6 BOLT – hex, 12 – 1.25 x 35 mm
32 33-1432T1 2 PLATE – retainer
33 33-1422T1 2 O-RING – yoke sealing, Part of transmission gasket kit P/N 90-8401T91.
34 33-1429T1 1 YOKE – output
35 33-1428T1 2 SEAL – output shaft, Part of transmission gasket kit P/N 90-8401T91.
36 90-8002T1 1 RETAINER – bearing, fifth shaft
37 90-8003T1 1 GASKET – bearing retainer, fifth shaft, Part of transmission gasket kit P/N 90-8401T91.
38 90-8004T1 1 YOKE – output, rear, 8C
39 90-7987T1 1 HOUSING – rear, transmission
40 S1080S00F 4 O-RING – plug, Part of transmission gasket kit P/N 90-8401T91.
41 S1090S00F 1 PLUG – magnetic
42 S1010S00F 3 PLUG – O-ring boss
43 514-841 2 BOLT – hex, 12 – 1.25 x 20 mm
44 514-834 6 BOLT – hex, 12 – 1.25 x 30 mm
45 33-1619T2 1 COVER – end, used on models without PTO
46 514-738 1 BOLT – hex, 10 – 1.25 x 45 mm
47 S1390S00F 1 PLUG – O-ring boss
48 S1320S00F 1 O-RING – plug, Part of transmission gasket kit P/N 90-7927T92
1 218-5140 1 ELBOW – 45 degree, 1-5/16-12 inch flare x adj O-ring boss
2 33-1874T91 1 PUMP – lubrication, component parts not serviced separately, According to Branko, there is not a
3 31-1394 1 ELBOW – hose stem, special
4 514-721 2 BOLT – hex, 10 – 1.25 x 30 mm
5 90-8007T1 2 BOLT – socket head, special
6 90-8008T1 2 BOLT – socket head, special
7 90-8009T91 1 VALVE ASSEMBLY – lock out, parts list Figure 6-100
8 514-729 2 BOLT – hex, 10 – 1.25 x 90 mm, class 8.8
9 514-739 2 BOLT – hex, 10 – 1.25 x 120 mm, class 8.8
10 90-8200T91 1 VALVE ASSEMBLY – control, parts list Figure 6-098
11 90-8012T1 1 GASKET – control valve, Part of transmission gasket kit P/N 90-8401T91.
12 614-8065 5 BOLT – hex, full threads, 8 – 1.25 x 65 mm
13 614-8100 3 BOLT – hex, full threads, 8 – 1.25 x 100 mm
14 S7000S01F 1 VALVE ASSEMBLY – regulator, parts list Figure 6-096
15 S1150S02F 1 GASKET – regulator valve, Part of transmission gasket kit P/N 90-8401T91.
16 S14701960 1 steel ball
17 33-156T1 1 suction tube
18 S1620S01F 1 suction tube gasket
19 S1700S00F 1 suction tube retainer plate
20 90-8259T1 1 valve control gasket
21 90-8260T1 1 valve assembly (p. list page 6-101)
22 814-8075 1 bolt, hex, 8 – 1.25 x 75 mm
1 614-6012 2 BOLT, Hex, M6 x 12, 8.8
2 90-7982T1 1 BAFFLE – breather
3 90-7983T1 1 LEVER – shift, second and third speed, inner
4 90-7984T1 1 LEVER – shift, C and D range, inner
5 33-1761T1 1 PLUG – taper
6 33-1454T1 1 FILTER – breather
7 33-1455T1 1 ELBOW – 90 degree, breather filter
8 SM8911246 1 NUT – hex, 16 mm – 1.5
9 90-7985T1 2 HOLDER – lever
10 514-712 4 BOLT – hex, 10 – 1.25 x 25 mm
11 33-1727T1 2 SEAL – holder, Part of transmission gasket kit P/N 90-8401T91.
12 90-7975T1 1 LEVER – shift, speed, outer
13 SM831050 2 PIN – spring
14 90-7977T1 1 LEVER – shift, range, outer
15 90-8006T1 1 GASKET – breather, Part of transmission gasket kit P/N 90-8401T91.
1 33-1767T1 7 BOLT – socket head, special
2 33-1807T1 2 PIN – dowel
3 90-8157T1 1 SHAFT – idler, reverse
4 90-7953T1 2 BEARING – tapered roller
5 90-7954T1 1 GEAR – idler, reverse
7 33-1693T1 1 PLATE – retainer
8 514-1021 1 Bolt, Hex, M16 x 1.5 x 35, 10.9, Full Thd
9 614-6012 7 BOLT, Hex, M6 x 12, 8.8
10 90-7955T1 1 GUTTER – input
11 514-832 12 BOLT – hex, 12 – 1.25 x 35 mm
12 90-7957T1 1 PLATE – support
13 90-7958T1 1 COVER – idler shaft
14 514-730 3 BOLT – hex, 10 – 1.25 x 35 mm
15 90-7959T1 1 GUTTER – bearing
16 90-7960T1 1 GUTTER – gear, second speed
17 90-7961T1 1 GUTTER – gear, first speed
18 90-7962T1 1 PIN – roll
20 90-7920T1 2 BEARING – tapered roller
21 90-7968T1 1 GEAR – idler
22 90-7969T1 1 SHAFT – idler
23 90-7970T1 1 O-RING – shaft, Part of transmission gasket kit P/N 90-8401T91.
24 90-7971T1 1 LEVER – shift, first-reverse speed, inner
25 90-7972T1 1 LEVER – shift, A-B range, inner
26 90-7973T1 2 PIN – dowel
27 90-7974T1 1 HOLDER – lever, first-reverse speed
28 514-712 4 BOLT – hex, 10 – 1.25 x 25 mm
29 33-1727T1 2 SEAL – holder, Part of transmission gasket kit P/N 90-8401T91.
30 90-7975T1 1 LEVER – shift, speed, outer
31 SM831050 3 PIN – spring
32 90-7976T1 1 HOLDER – lever, A-B range
33 90-7977T1 1 LEVER – shift, range, outer
34 90-7978T1 1 PAN – oil
35 514-703 2 BOLT – hex, 10 – 1.25 x 20 mm
37 514-842 2 BOLT – hex, 12 – 1.25 x 25 mm
38 825-11410 2 NUT – hex, 10 mm – 1.25
39 90-7979T1 1 BRACKET – oil pan, left-hand
40 90-7980T1 1 BRACKET – oil pan, right-hand
41 90-7987T1 1 HOUSING – rear, transmission
42 90-7948T1 12 WASHER – wave
36 895-11010 2 WASHER – flat, 11 x 20 x 2 mm
1 514-843 13 BOLT – hex, 12 – 1.25 x 60 mm
2 33-1467T1 2 PIN – dowel
3 90-8252T91 1 SHAFT ASSEMBLY – input, parts list Figures 6-082 and 6-086
4 90-7986T91 1 SHAFT ASSEMBLY – fourth, parts list Figure 6-092
5 90-7987T1 1 HOUSING – rear, transmission
6 90-7988T91 1 SHAFT ASSEMBLY – third, parts list Figure 6-090
7 514-703 2 BOLT – hex, 10 – 1.25 x 20 mm
8 33-1746T1 1 PLATE – lock
9 90-8422T1 1 HOUSING – front, transmission
10 514-830 16 BOLT – hex, 12 – 1.25 x 40 mm
11 90-7990T91 1 SHAFT ASSEMBLY – fifth, parts list Figure 6-094
12 33-1812T1 1 LIP – oil, reverse gear
13 614-6012 2 BOLT, Hex, M6 x 12, 8.8
14 90-8251T91 1 SHAFT ASSEMBLY – pump drive, parts list Figure 6-088
15 90-7944T1 1 FORK – shift, first-reverse, See Figure 6-080 for additional parts
15 90-7949T1 1 FORK – shift, second-third speeds, See Figure 6-080 for additional parts
15 90-7950T1 1 FORK – shift, C-D ranges, See Figure 6-080 for additional parts
15 90-7951T1 1 FORK – shift, A-B ranges, See Figure 6-080 for additional parts
1 90-7944T1 1 FORK – shift, first-reverse
2 33-1757T1 4 BALL – steel, fork detent
3 33-1786T1 4 SPRING – detent ball
4 33-1759T1 4 PLUG – detent spring
5 90-7945T1 1 ROD – shift, speed
6 90-7946T1 1 PLATE – interlock
7 90-7947T1 2 PIN – spring
8 33-1756T1 2 BALL – steel
9 33-1745T1 2 O-RING – seal, fork, Part of transmission gasket kit P/N 90-8401T91.
10 90-7949T1 1 FORK – shift, second-third speeds
11 90-7950T1 1 FORK – shift, C-D ranges
12 90-7951T1 1 FORK – shift, A-B ranges
13 90-7952T1 1 ROD – shift, range
2 90-7920T1 1 BEARING – tapered roller
3 90-7921T1 2 WASHER – thrust
4 90-7922T1 1 BEARING – thrust
5 90-7923T1 1 COLLAR – bearing
6 90-8203T1 1 GEAR – drive, input
7 33-1829T1 1 RING – retaining
8 90-8204T1 2 BEARING – needle
9 S5040S00F 5 RING – retaining
10 S5230S00F 1 WASHER – thrust
11 A75158 1 BEARING – thrust, replaces S5050S00F bearing
12 90-7925T1 2 WASHER – thrust
13 S14701960 1 BALL – steel
14 90-8205T1 1 SHAFT – input
15 514-721 14 BOLT – hex, 10 – 1.25 x 30 mm
19 90-7930T1 1 COVER – clutch
21 33-1663T1 8 PLATE – clutch, friction
22 33-1785T1 32 PLATE – separating, clutch
23 S4410S00F 2 RING – piston, shaft, Part of transmission gasket kit P/N 90-8401T91.
24 90-7932T1 12 SPRING – return
25 90-7933T1 1 PISTON – clutch, prior to P.I.N. JEE0071001
25 90-8389T1 1 PISTON – clutch, P.I.N. JEE0071001 and after
26 33-1662T1 1 RING – seal, large, prior to P.I.N. JEE0071001, Part of transmission gasket kit P/N 90-7927T92
26 90-8385T1 1 RING – seal, P.I.N. JEE0071001 and after, Part of transmission gasket kit P/N 90-8401T91.
27 S2630S00F 1 RING – sealing, prior to P.I.N. JEE0071001, Part of transmission gasket kit P/N 90-7927T92
27 90-8386T1 1 RING – seal, P.I.N. JEE0071001 and after, Part of transmission gasket kit P/N 90-8401T91.
28 90-7934T1 12 PIN – guide, use with 90-7932T1 return spring, Ref. 24
29 33-1659T1 4 PIN – guide, use with 33-1785T1 separating plate, Ref. 22
30 90-8231T1 1 DRUM – clutch, prior to P.I.N. JEE0071001
30 90-8387T1 1 DRUM – clutch, P.I.N. JEE0071001 and after
31 90-8232T1 1 GEAR – driven, pump
32 514-718 16 BOLT – hex, 10 – 1.25 x 40 mm
34 90-8230T1 1 BEARING – tapered roller
1 90-8233T1 1 RING – snap
2 90-8234T1 1 PLATE – end, clutch
3 90-8235T1 2 PLATE – faced, clutch
5 33-1519T2 3 PLATE – faced
6 90-8236T1 1 PLATE – spring
7 90-8237T1 1 PISTON – clutch
8 90-8238T1 1 DRUM – clutch
9 33-1416T1 1 RING – retaining
10 90-8239T1 1 O-RING – special, Part of transmission gasket kit P/N 90-8401T91.
11 S2640S00F 12 SPRING – return
12 90-8240T1 1 GEAR – drive, input
13 90-7937T1 1 CONE – tapered roller bearing
15 90-7938T1 5 RING – seal, Part of transmission gasket kit P/N 90-8401T91.
16 514-721 10 BOLT – hex, 10 – 1.25 x 30 mm
17 S5040S00F 1 RING – retaining
18 90-8230T1 1 BEARING – tapered roller
19 S4410S00F 1 RING – piston, Part of transmission gasket kit P/N 90-8401T91.
20 S2630S00F 1 RING – sealing, Part of transmission gasket kit P/N 90-8401T91.
1 529208R1 1 CUP – tapered roller bearing
1 529207R91 1 CONE – tapered roller bearing
2 90-7939T1 1 COUPLING – sleeve, pump
3 33-1416T1 2 RING – retaining
4 90-8241T1 1 WASHER – thrust
5 90-8242T1 1 GEAR – drive, high
6 90-8243T1 2 BEARING – needle
7 S5040S00F 1 RING – retaining
8 90-8244T1 1 WASHER – thrust
9 90-8245T1 2 RING – snap
10 90-8233T1 1 RING – snap
11 90-8234T1 1 PLATE – end, clutch
12 90-8235T1 2 PLATE – faced, clutch
14 33-1519T2 3 PLATE – faced
15 90-8236T1 1 PLATE – spring
16 S2640S00F 12 SPRING – return
17 90-8237T1 1 PISTON – clutch
18 S2630S00F 3 RING – sealing, Part of transmission gasket kit P/N 90-8401T91.
19 S4410S00F 1 RING – piston, Part of transmission gasket kit P/N 90-8401T91.
20 90-7941T1 1 PIN – dowel
21 90-8246T1 1 BALL – steel
22 90-8247T1 1 NEEDLE – shaft
23 90-8248T1 1 SHAFT – pump
24 90-8239T1 1 O-RING – special, replaces 90-8249T1 O-ring, Part of transmission gasket kit P/N 90-8401T91.
25 90-8238T1 1 DRUM – clutch
26 90-8250T1 1 GEAR – input
27 90-7937T1 1 CONE – tapered roller bearing
28 90-7938T1 3 RING – seal, Part of transmission gasket kit P/N 90-8401T91.
29 514-738 10 BOLT – hex, 10 – 1.25 x 45 mm
2 33-1708T1 1 BEARING – tapered roller
3 90-7893T1 1 GEAR – driven, third shaft
4 S5040S00F 2 RING – retaining
5 90-7894T1 1 GEAR – drive, first speed
6 90-7895T1 4 DISK – synchro, speed
7 90-7904T1 4 RING – retaining
8 SM832508 16 PIN – spring
9 90-7896T1 1 RING – retaining
10 S5070S00F 1 BEARING – needle
11 33-1830T1 2 SYNCHRONIZER – speed
12 S5090S00F 4 RING – retaining
13 90-8013T1 1 RING – retaining
14 90-7897T1 1 GEAR – drive, reverse speed
15 90-8014T1 1 RING – retaining
16 90-8015T1 1 BEARING – needle
17 90-7898T1 1 SHAFT – speed
18 90-7899T1 1 GEAR – drive, second speed
19 90-7900T1 1 GEAR – drive, third speed
20 90-7901T1 1 SPACER – third speed gear
21 33-1676T1 1 BEARING – tapered roller
2 33-1676T1 2 BEARING – tapered roller, shaft
3 90-7909T1 1 GEAR – drive, A range
4 90-7910T1 1 GEAR – driven, first speed
5 90-7911T1 1 SHAFT – center, fourth
6 90-7912T1 1 GEAR – drive, B range
7 90-7913T1 1 GEAR – driven, second speed
8 S5090S00F 1 RING – retaining
9 S5040S00F 1 RING – retaining
10 90-7914T1 1 GEAR – driven, third speed
11 90-7915T1 1 GEAR – driven, D range
1 33-1708T1 1 BEARING – tapered roller
2 S5230S00F 2 WASHER – thrust
3 A75158 1 BEARING – thrust, replaces S5050S00F bearing
4 S5070S00F 2 BEARING – needle
5 90-7902T1 1 GEAR – driven, A range
6 90-7903T1 4 DISK – synchro, range
7 90-7904T1 4 RING – retaining
8 SM832508 16 PIN – spring
9 33-1831T1 2 SYNCHRONIZER – range
10 S5090S00F 4 RING – retaining
11 90-7905T1 1 GEAR – driven, B range
12 90-7906T1 1 SHAFT – output
13 90-7907T1 1 GEAR – driven, C range
14 90-7908T1 1 GEAR – driven, D range
15 33-1676T1 1 BEARING – tapered roller
16 S4150S00F 2 RING – sealing, Part of transmission gasket kit P/N 90-8401T91.
17 33-1695T1 1 PISTON – carrier, ring
1 S1040S00F 9 O-RING – plug, Part of transmission gasket kit P/N 90-8401T91.
2 S1030S00F 1 PLUG – hex, O-ring boss
3 S7090S00F 1 GASKET – valve cover, Part of transmission gasket kit P/N 90-8401T91.
4 S7110S00F 1 COVER – valve body
5 614-8020 5 BOLT – hex, full threads, 8 – 1.25 x 20 mm
6 S7030S01F 1 VALVE – regulator
8 S7120S00F 1 SPRING – compression
9 S7050S00F 2 SPRING – compression
10 S7020S00F 1 ROD – pressure
11 S7070S00F 1 SPRING – compression
13 S7060S00F 2 VALVE – lube
15 S1320S00F 1 O-RING – plug, Part of transmission gasket kit P/N 90-8401T91.
16 S1390S00F 1 PLUG – O-ring boss
1 S6170S00F 1 PLUG – hex, valve
2 S6180S00F 1 O-RING – plug, Part of transmission gasket kit P/N 90-8401T91.
3 S6260S00F 8 BOLT – socket head, special
4 S6010S00F 1 SPOOL – reducing
5 S6220S00F 11 PLUG – valve
6 S6020S00F 1 COVER – valve
7 S6030S00F 1 GASKET – valve cover, Part of transmission gasket kit P/N 90-8401T91.
8 S6040S00F 1 SPOOL – modulator
9 S6160S00F 1 POPPET – spool, valve
10 S6240S00F 1 PLUG – orifice
11 S6230S00F 2 PLUG – orifice
12 90-8016T1 1 BODY – control valve
13 S6060S00F 1 SEAT – spring
14 90-8199T1 1 SPRING – tension
15 S6080S00F 1 LINK – connecting
16 S6150S00F 1 SPRING – compression
18 S6200S00F 1 SPACER – 31 x 1.2 mm thick
19 S6130S00F 1 PIN – roll
20 S6100S00F 1 STEM – control
21 90-8017T1 1 GASKET – cover, Part of transmission gasket kit P/N 90-8401T91.
22 90-8018T1 1 COVER – control stem
23 S6120S00F 1 O-RING – control stem, Part of transmission gasket kit P/N 90-8401T91.
24 S6110S00F 1 SEAL – control stem, Part of transmission gasket kit P/N 90-8401T91.
1 90-8151T1 1 PLUG – hex cap
2 90-8152T1 2 O-RING – plug
3 90-8021T1 1 PLUG – orifice, lock out valve
4 90-8153T1 1 SPOOL – lock out valve
5 90-8154T1 1 SPRING – return
6 90-8019T1 1 BODY – lock out valve
7 90-8155T1 1 PLUG – port
8 90-8020T1 5 O-RING – seal
9 90-8156T1 1 PLUG – orifice
14 33-1534T1 1 RING – snap, hi-lo contol valve
20 33-1537T1 1 O-RING – seal, filter, hi-lo contol valve
21 33-1538T1 1 FILTER – conical, hi-lo contol valve
22 33-1539T1 1 PLUG – filter, hi-lo contol valve
1 60-6060T91 1 CONTROL ASSEMBLY – mode, forward or reverse, parts list Figure 6-104
2 60-6483T92 1 CONTROL ASSEMBLY – pulser, upshift or downshift, parts list Figure 6-106
3 60-7160T1 1 CONTROLLER – transmission, transmission, electronic, prior to P.I.N. JEE0071001
3 60-7287T1 1 CONTROLLER – transmission, electronic, P.I.N. JEE0071001 and after
5 60-6140T1 1 PLATE – wear, mode control
6 19-1018 4 SCREW – pan head, self-tapping, special, No. 10 NS x 3/4 inch
7 495-11028 6 WASHER – flat, 9/32 x 5/8 x 1/16 inch
8 19-6082 6 NUT – lock, 1/4 inch NC
9 60-6036T1 1 KNOB – shift handle
10 19-5798 2 SCREW – set, No. 8 NC
16 60-6488T2 1 KNOB – shift handle
17 60-6480T1 1 PLATE – retaining, switch
18 260-1338 2 SCREW – self-tapping, pan Phillips, No. 6-20 x 1/2 inch
19 60-6482T2 1 SWITCH – includes washer, skip-shift
20 60-6479T1 1 CONNECTOR – electrical
21 22-824 2 STRAP – tie, 7 inch, nylon
1 60-6057T2 1 HOUSING – upper, control assembly
2 60-5887T1 1 TRUNNION – shift control
3 60-6141T1 4 BUSHING – flanged, nylon
4 60-6756T1 1 YOKE – pivot, shift control
5 60-5892T1 1 PIN – spring tension
6 60-6056T1 1 STRIKER – switch actuating
8 60-6059T91 1 SWITCH – neutral
11 60-6197T1 1 SPRING – return
12 19-6034 3 WASHER – spring, 1/2 x 1 x 1/64 inch
13 432-816 2 1/8″ x 1″
14 19-6158 1 PIN – clevis, 1/2 x 2-3/4 inch
15 H382416 1 PIN – clevis, 1/2 x 2-1/4 inch
16 111626C1 1 NUT – hex, self-locking, special, 1/4 inch NC
17 413-440 1 BOLT – hex, 1/4 NC x 2-1/2 inch
18 493-11014 2 WASHER – internal-external tooth lock, 1/8 inch
19 225-14106 2 Nut, #6-32
20 470-10620 2 SCREW – machine, pan head slotted, No. 6 NC x 1-1/4 inch
21 492-11006 2 Washer, Lock, #6
22 495-31016 2 WASHER – flat, 5/32 x 3/8 x 3/64 inch
23 193-1002 1 NUT – hex, with external tooth lock washer, No. 8 NC
35 20-1316T1 1 ACTUATOR – mode
36 495-21019 2 WASHER, #8
1 60-6485T1 1 BRACKET – pulser control
2 60-6484T2 1 LEVER – control, pulser
3 60-6141T1 2 BUSHING – flanged, nylon
4 60-5892T1 1 PIN – spring tension
8 60-6197T1 1 SPRING – return
9 19-6034 2 WASHER – spring, 1/2 x 1 x 1/64 inch
10 432-816 1 1/8″ x 1″
11 H382416 1 PIN – clevis, 1/2 x 2-1/4 inch
12 111626C1 1 NUT – hex, self-locking, special, 1/4 inch NC
13 413-440 1 BOLT – hex, 1/4 NC x 2-1/2 inch
14 20-1316T1 1 ACTUATOR – magnet
15 495-21019 2 WASHER, #8
16 193-1002 1 NUT – hex, with external tooth lock washer, No. 8 NC
1 60-6623T1 2 KNOB – control lever
2 60-6645T1 1 LEVER – range shift
3 60-6644T1 1 LEVER – gear shift
4 60-6655T1 2 PLATE – control lever pattern
5 495-31022 12 WASHER, #10
6 86632551 12 NUT, LOCK, #10-24, GB
7 60-6614T2 2 BRACKET – lever, inner
8 60-6615T2 2 BRACKET – lever, outer
9 60-6617T1 4 PLATE – support, lever
10 363-30812 8 SCREW – machine, hex washer head, No. 8 NC x 3/4 inch
11 131-29 8 NUT – hex, self-locking, No. 8 NC
15 60-6622T1 2 SPRING – lever
16 60-4293T1 2 TRUNNION – lever
17 495-11053 4 WASHER, 1/2″, SAE (17/32″ x 1-1/16″ x 3/32″)
18 90-4368T1 4 BUSHING – pivot
19 90-4367T1 4 BUSHING – pivot, long
20 19-5400 2 PIN – hair, 1/8 inch
21 426-8136 1 BOLT – hex, 1/2 NC x 8-1/2 inch, grade 8
22 425-108 1 NUT – hex, 1/2 inch NC
1 60-6564T2 2 CABLE – shift lever, gears, R-1-2-3
2 60-6641T1 1 CABLE – shift lever, C-D range
3 60-6640T1 1 CABLE – shift lever, A-B range
4 19-6233 4 JOINT – ball
5 426-620 4 BOLT – hex, 3/8 NC x 1-1/4 inch, grade 8
6 231-1446 12 NUT, LOCK, 3/8″-16, GB
7 60-6668T3 1 MOUNT – cable
8 426-516 4 BOLT – hex, 5/16 NC x 1 inch, grade 8
9 60-4279T2 4 BOOT – rubber
10 425-105 4 NUT – hex, 5/16 inch NC
11 22-824 4 STRAP – tie, 7 inch
13 90-7768T1 1 BRACKET – cable support
14 426-816 2 BOLT – hex, 1/2 NC x 1 inch, grade 8
15 90-7452T1 4 U-BOLT – retainer, cable
16 232-4136 8 NUT, LOCK, 3/8″-16, GC
17 90-7453T1 4 SADDLE – clamp
19 213-126 4 CLEVIS – adjustable, 3/8 inch NF
20 427-6106 4 PIN, CLEVIS, 3/8″ x 1 1/16″, Hardened
21 19-5400 4 PIN – hair, 1/8 inch
25 90-7769T1 1 BRACKET – mounting, cable
26 426-816 2 BOLT – hex, 1/2 NC x 1 inch, grade 8
27 90-7770T1 1 PLATE – mounting, cable
28 413-1028 2 BOLT – hex, 5/8 NC x 1-3/4 inch
29 90-7975T1 1 LEVER – shift, speed, outer
30 90-7977T1 1 LEVER – shift, range, outer
31 90-7977T1 1 LEVER – shift, range, outer
32 90-7975T1 1 LEVER – shift, speed, outer
33 60-6615T2 2 BRACKET – lever, outer
34 60-6614T2 2 BRACKET – lever, inner
1 60-6835T1 1 PEDAL – clutch
2 60-6836T1 1 BUSHING – pivot
3 425-1512 2 NUT – hex, jam, 3/4 inch NF
4 19-5635 2 WASHER – flat, 1 x 1-3/4 x 3/32 inch
5 495-21056 1 WASHER – flat, 9/16 x 1-3/8 x 7/64 inch
6 426-816 1 BOLT – hex, 1/2 NC x 1 inch, grade 8
10 2-5000T1 1 SPRING – pedal return
11 495-11041 6 WASHER – flat, 13/32 x 13/16 x 1/16 inch
12 19-5922 1 PIN – clevis, 3/8 x 1-1/4 inch
13 32-612 1 PIN, SPLIT (COTTER), 3/32″ x 3/4″
14 60-4384T1 1 CLEVIS – cable end
15 425-155 3 NUT – hex, jam, 5/16 inch NF
18 60-5048T2 1 BRACKET – actuator mounting, Used on tractors equipped with Power Shift transmissions only.
19 495-21019 2 WASHER, #8 , Used on tractors equipped with Power Shift transmissions only.
20 131-29 1 NUT – hex, self-locking, No. 8 NC, Used on tractors equipped with Power Shift transmissions only.
21 20-1316T1 1 ACTUATOR – mode, magnetic, Used on tractors equipped with Power Shift transmissions only.
25 60-6027T1 1 SENSOR – proximity, Used on tractors equipped with Power Shift transmissions only.
26 60-6025T1 1 BRACKET – control mounting
27 425-104 3 NUT – hex, 1/4 inch NC
28 20-2333T1 1 SWITCH – micro
29 60-2666T1 1 WIRE – switch
30 470-10620 2 SCREW – machine, pan head slotted, No. 6 NC x 1-1/4 inch
31 495-31016 2 WASHER – flat, 5/32 x 3/8 x 3/64 inch
32 225-14106 2 Nut, #6-32
35 426-628 1 BOLT – hex, 3/8 NC x 1-3/4 inch, grade 8
36 425-106 1 NUT, 3/8″-16, G5
39 60-4957T1 1 CABLE – clutch actuating, 75 inch long
40 248-2376 1 GROMMET – rubber, 1-1/4 inch groove diameter, cable guard
41 425-1512 1 NUT – hex, jam, 3/4 inch NF
45 90-8048T1 1 RETAINER – cable guard
46 458-412 2 BOLT – hex flange, 1/4 NC x 3/4 inch
47 90-8047T1 1 GUARD – cable
50 60-6241T1 1 COLLAR – cable
51 19-6041 1 PIN – headless
52 32-212 2 PIN, SPLIT (COTTER), 1/32″ x 3/4″
55 60-5074T1 1 MOUNT – pedal, brake and clutch, See Figures 7-02 or 7-04 for mounting hardware
1 50-3494T91 1 FILTER ASSEMBLY – oil, transmission, parts list Figure 8-034
2 426-616 2 BOLT, Hex, 3/8″-16 x 1″, G8, Full Thd
3 495-11041 2 WASHER – flat, 13/32 x 13/16 x 1/16 inch
4 218-5110 1 ELBOW – 90 degree, 1-5/16-12 inch flare x adj O-ring boss, with three point hitch
4 218-5069 1 ADAPTER – straight, 1-5/16-12 inch flare x O-ring boss, without three point hitch, Includes: Ref. 5
9 218-5069 3 ADAPTER – straight, 1-5/16-12 inch flare x O-ring boss, Includes: Ref. 10
12 50-2668T1 1 PLATE – clamp support
13 50-2965T1 1 CLAMP – double, hoses
14 31-1486 2 HOSE – filter to cooler
15 218-5064 2 ADAPTER – straight, 1-1/16-12 inch flare x O-ring boss, Includes: Ref. 16
16 237-6014 2 O-RING, 14-1, 90 Duro, 1.048″ ID x .116″ Thk
19 31-2938 1 HOSE – filter to transmission
20 90-6894T1 1 BRACKET – clamp mounting, tube support
24 31-3014 1 HOSE – 2058 mm (82 inch) long, filter to pump
25 33-1524T91 1 PUMP ASSEMBLY – transmission lubrication, parts list Figure 6-030
26 90-7490T1 1 TUBE – dipstick
27 218-5072 1 ADAPTER – straight, 1-5/8-12 inch flare x O-ring boss, Includes: Ref. 28
28 237-6020 1 O-RING, 20-1, 90 Duro, 1.475″ ID x .118″ Thk
29 90-6546T1 1 DIPSTICK – oil check
30 31-1283 2 CLAMP – adjustable, 1-1/4 x 2-5/8 inch
31 1-4571 1 HOSE – 114 mm (4-1/2 inch) long, cut from 1-4482 bulk hose, see below, pump to transmission
34 238-6222 1 O-RING, -222, 90 Duro, 1.484″ ID x .139″ Thk
35 90-7064T1 1 TUBE – pump to transmission, without PTO
35 90-7063T1 1 TUBE – pump to transmission, with PTO
36 31-1910 2 FLANGE – split, clamp halves
37 426-624 4 BOLT – hex, 3/8 NC x 1-1/2 inch, grade 8
39 515-23317 1 CLAMP, 1 1/4″, Insul, 3/8″ Bolt, P-type
40 515-23381 2 CLAMP, 1 1/2″, Insul, 3/8″ Bolt, P-type
41 90-6588T1 1 BRACKET – support
42 425-106 2 NUT, 3/8″-16, G5
45 425-105 2 NUT – hex, 5/16 inch NC
47 50-2534T1 2 CLAMP – split, one-half
48 50-2533T1 1 PLATE – clamp support
49 90-6708T1 1 COOLER – oil, hydraulic, used on 9370 and 9380, See Figure 8-040 for cooler mounting
49 90-8163T1 1 COOLER – oil, hydraulic, used on 9390, See Figure 8-040 for cooler mounting
52 426-612 2 BOLT – hex, 3/8 NC x 3/4 inch, grade 8
55 426-540 1 BOLT – hex, 5/16 NC x 2-1/2 inch, grade 8
56 495-21038 1 WASHER – flat, 3/8 x 7/8 x 3/32 inch
57 50-3675T1 1 ADAPTER – drain plug, special, Part of heater maintainer kit P/N 35-2016T91.
58 A164503 1 HEATER – transmission, with cordset, Part of heater maintainer kit P/N 35-2016T91.
59 515-2363 2 CLAMP – P-type, 1/4 inch ID, Part of heater maintainer kit P/N 35-2016T91.
60 22-824 7 STRAP – tie, 7 inch, not shown, Part of heater maintainer kit P/N 35-2016T91.
5 238-6021 1 O-Ring, -021, 90 Duro, .926″ ID x .070″ Thk
10 238-6021 1 O-Ring, -021, 90 Duro, .926″ ID x .070″ Thk
1 50-3494T91 1 FILTER ASSEMBLY – oil, transmission, parts list Figure 8-034
2 426-616 2 BOLT, Hex, 3/8″-16 x 1″, G8, Full Thd
3 495-11041 2 WASHER – flat, 13/32 x 13/16 x 1/16 inch
4 50-3675T1 1 ADAPTER – drain plug, special, Part of heater maintainer kit P/N 35-2016T91.
5 A164503 1 HEATER – transmission, with cordset, Part of heater maintainer kit P/N 35-2016T91.
6 515-2363 2 CLAMP – P-type, 1/4 inch ID, Part of heater maintainer kit P/N 35-2016T91.
7 22-824 7 STRAP – tie, 7 inch, not shown, Part of heater maintainer kit P/N 35-2016T91.
9 218-5069 2 ADAPTER – straight, 1-5/16-12 inch flare x O-ring boss, Includes: Ref. 10
12 50-2668T1 1 PLATE – clamp support
13 50-2965T1 1 CLAMP – double
14 31-1486 2 HOSE – cooler to filter
15 218-5064 2 ADAPTER – straight, 1-1/16-12 inch flare x O-ring boss, Includes: Ref. 16
16 237-6014 2 O-RING, 14-1, 90 Duro, 1.048″ ID x .116″ Thk
19 31-2911 1 HOSE – 1321 mm (52 inch) long, transmission to filter
20 218-5110 1 ELBOW – 90 degree, 1-5/16-12 inch flare x adj O-ring boss, Includes: Ref. 21
21 237-6016 1 O-RING – 1-11/64 ID x 7/64 inch wide
24 31-3015 1 HOSE – filter to pump
25 33-1874T91 1 PUMP – lubrication, component parts not serviced separately, Part of lubrication pump O-ring kit P/N
26 90-7490T1 1 TUBE – dipstick
27 218-5072 1 ADAPTER – straight, 1-5/8-12 inch flare x O-ring boss, Includes: Ref. 28
28 237-6020 1 O-RING, 20-1, 90 Duro, 1.475″ ID x .118″ Thk
29 90-7826T1 1 DIPSTICK – oil check
30 31-1283 2 CLAMP – adjustable, 1-1/4 x 2-5/8 inch
31 1-4571 1 HOSE – 114 mm (4-1/2 inch) long, cut from 1-4482 bulk hose, see below
34 90-7825T1 1 TUBE – pump to transmission
35 238-6222 1 O-RING, -222, 90 Duro, 1.484″ ID x .139″ Thk
36 31-1910 2 FLANGE – split, clamp halves
37 426-624 4 BOLT – hex, 3/8 NC x 1-1/2 inch, grade 8
39 515-23317 1 CLAMP, 1 1/4″, Insul, 3/8″ Bolt, P-type
40 515-23381 1 CLAMP, 1 1/2″, Insul, 3/8″ Bolt, P-type
41 90-6588T1 1 BRACKET – support
42 425-106 2 NUT, 3/8″-16, G5
45 425-105 2 NUT – hex, 5/16 inch NC
47 50-2534T1 1 CLAMP – split, one-half
48 50-2533T1 1 PLATE – clamp support
49 90-6708T1 1 COOLER – oil, hydraulic, used on 9370 and 9380, See Figure 8-040 for cooler mounting
49 90-8163T1 1 COOLER – oil, hydraulic, used on 9390, See Figure 8-040 for cooler mounting
51 50-2037T1 1 STRAP – tie
52 218-5140 1 ELBOW – 45 degree, 1-5/16-12 inch flare x adj O-ring boss, Includes: Ref. 53
54 426-612 2 BOLT – hex, 3/8 NC x 3/4 inch, grade 8
55 426-540 1 BOLT – hex, 5/16 NC x 2-1/2 inch, grade 8
56 495-21038 1 WASHER – flat, 3/8 x 7/8 x 3/32 inch
10 238-6021 1 O-Ring, -021, 90 Duro, .926″ ID x .070″ Thk
53 238-6021 1 O-Ring, -021, 90 Duro, .926″ ID x .070″ Thk
1 90-6691T1 1 TUBE – lubrication, range selector valve to PTO control valve
2 218-5280 1 ELBOW – 90 degree, 3/4-16 flare x 9/16-18 inch adj O-ring boss, Includes: Ref. 3
5 218-5121 1 ELBOW – 90 degree, 3/4-16 flare x 7/8-14 inch adj O-ring boss, Includes: Ref. 6
6 237-6010 1 O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
8 218-5059 1 ADAPTER – straight, 3/4-16 inch flare x O-ring boss, Includes: Ref. 9
9 237-6008 1 O-Ring, 8-1, 90 Duro, .644″ ID x .087″ Thk
12 218-5230 2 ELBOW – 90 degree, 3/4-16 inch flare x swivel
13 218-5060 1 ADAPTER – straight, 3/4-16 flare x 7/8-14 inch O-ring boss, Includes: Ref. 14
14 237-6010 1 O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
17 90-6889T1 1 TUBE – lubrication, regulator valve to PTO control valve
18 90-6894T1 1 BRACKET – clamp mounting, tube support
19 515-23127 1 CLAMP – P-type, 1/2 inch ID, tube
20 SM8121240 1 BOLT – hex, 12 – 1.75 x 40 mm
21 426-612 4 BOLT – hex, 3/8 NC x 3/4 inch, grade 8
22 425-106 4 NUT, 3/8″-16, G5
25 217-173 1 FITTING, 1″ Hose x 1 5/8″-12 ORB, Beaded, Includes Ref. 26
26 237-6020 1 O-RING, 20-1, 90 Duro, 1.475″ ID x .118″ Thk
29 214-1420 2 CLAMP – adj, 13/16 – 1-3/4 inch dia, hose retaining
30 31-3188 1 HOSE – 2946 mm (116 inch) long, cut from S118383X bulk hose, suction, transmission, see below
33 90-7256T1 1 FLANGE – hose adapter, 1 inch hose end
34 426-712 4 BOLT – hex, 7/16 NC x 5/8 inch, grade 8
35 218-5106 1 ELBOW – 90 degree, 3/4-16 inch flare x adj O-ring boss, Includes: Ref. 36
36 237-6008 1 O-Ring, 8-1, 90 Duro, .644″ ID x .087″ Thk
37 31-2537 1 CONNECTOR – orificed
38 31-2908 1 HOSE – lube, PTO valve to PTO housing
39 218-845 1 TEE – 3/4-16 inch flare branch x flare x swivel
40 218-755 1 CAP, 37є, 3/4″-16
44 218-5351 1 ADAPTER – straight, 3/4-16 flare x 9/16-18 inch O-ring boss, Includes: Ref. 45
46 426-516 1 BOLT – hex, 5/16 NC x 1 inch, grade 8
47 31-2361 1 CLAMP – P-type
48 50-2037T1 1 STRAP – tie
49 50-3220T1 1 CONDUIT – hose, flex, 1829 mm (72 inch) long, cut from S119717X bulk conduit, see below
50 22-824 3 STRAP – tie, 7 inch, not shown
3 237-6006 1 O-Ring, 6-1, 90 Duro, .468″ ID x .078″ Thk
45 237-6006 1 O-Ring, 6-1, 90 Duro, .468″ ID x .078″ Thk
1 217-173 1 FITTING, 1″ Hose x 1 5/8″-12 ORB, Beaded, Includes Ref. 2
2 237-6020 1 O-RING, 20-1, 90 Duro, 1.475″ ID x .118″ Thk
3 31-3188 1 HOSE – 2946 mm (116 inch) long, cut from S118383X bulk hose, suction, transmission, see below
4 214-1420 2 CLAMP – adj, 13/16 – 1-3/4 inch dia
5 50-2037T1 1 STRAP – tie
6 31-2361 1 CLAMP – P-type
7 426-516 1 BOLT – hex, 5/16 NC x 1 inch, grade 8
8 495-11034 1 WASHER – flat, 11/32 x 11/16 x 1/16 inch
9 90-7256T1 1 FLANGE – hose adapter, 1 inch hose end
10 426-712 4 BOLT – hex, 7/16 NC x 5/8 inch, grade 8
11 218-5059 1 ADAPTER – straight, 3/4-16 inch flare x O-ring boss, Includes: Ref. 12
12 237-6008 1 O-Ring, 8-1, 90 Duro, .644″ ID x .087″ Thk
13 31-2908 1 HOSE – lube, PTO valve to PTO housing
14 218-5106 1 ELBOW – 90 degree, 3/4-16 inch flare x adj O-ring boss, Includes: Ref. 15
15 237-6008 1 O-Ring, 8-1, 90 Duro, .644″ ID x .087″ Thk
16 31-2537 1 CONNECTOR – orificed
17 22-824 3 STRAP – tie, 7 inch
18 218-845 1 TEE – 3/4-16 inch flare branch x flare x swivel
19 218-755 1 CAP, 37є, 3/4″-16
20 218-5351 1 ADAPTER – straight, 3/4-16 flare x 9/16-18 inch O-ring boss, Includes: Ref. 21
22 515-23127 1 CLAMP – P-type, 1/2 inch ID
23 425-106 2 NUT, 3/8″-16, G5
24 426-616 2 BOLT, Hex, 3/8″-16 x 1″, G8, Full Thd
25 50-3543T2 1 TUBE – lubrication, regulator sub plate to PTO housing
26 218-5173 1 ELBOW – 45 degree, 3/4-16 inch flare x swivel
27 90-6894T1 1 BRACKET – clamp mounting, tube support
28 218-5230 2 ELBOW – 90 degree, 3/4-16 inch flare x swivel
30 50-3544T2 1 TUBE – main pressure, regulator valve to PTO control valve
31 50-3220T1 1 CONDUIT – hose, flex, 1829 mm (72 inch) long, cut from S119717X bulk conduit, see below
32 218-5280 1 ELBOW – 90 degree, 3/4-16 flare x 9/16-18 inch adj O-ring boss, Includes: Ref. 33
33 237-6008 1 O-Ring, 8-1, 90 Duro, .644″ ID x .087″ Thk
34 218-5121 1 ELBOW – 90 degree, 3/4-16 flare x 7/8-14 inch adj O-ring boss, Includes: Ref. 35
35 237-6008 1 O-Ring, 8-1, 90 Duro, .644″ ID x .087″ Thk
36 218-5060 1 ADAPTER – straight, 3/4-16 flare x 7/8-14 inch O-ring boss, Includes: Ref. 37
37 237-6008 1 O-Ring, 8-1, 90 Duro, .644″ ID x .087″ Thk
21 237-6006 1 O-Ring, 6-1, 90 Duro, .468″ ID x .078″ Thk
1 90-7510T91 1 SHAFT ASSEMBLY – drive, engine to transmission (8C), Power Shift, parts list Figure 6-128
1 90-7690T91 1 SHAFT ASSEMBLY – drive, engine to transmission, SynchroShift, parts list Figure 6-130
2 428-832 24 BOLT – hex, 1/2 NF x 2 inch, grade 8
3 426-1024 10 BOLT – hex, 5/8 NC x 1-1/2 inch, grade 8
4 90-7558T1 1 DAMPER – vibration
5 90-7523T1 1 SHIELD – upper, drive shaft, SynchroShift
6 70-6412T1 12 WASHER – special
7 426-716 12 BOLT – hex, 7/16 NC x 1 inch, grade 8
12 90-7521T1 1 SHIELD – upper, drive shaft, Power Shift
13 90-6743T1 1 SHIELD – lower, drive shaft
16 426-516 4 BOLT – hex, 5/16 NC x 1 inch, grade 8
17 495-11034 4 WASHER – flat, 11/32 x 11/16 x 1/16 inch
18 231-1445 4 NUT – hex, self-locking, 5/16 inch NC
19 426-828 2 BOLT – hex, 1/2 NC x 1-3/4 inch, grade 8
21 425-1012 2 NUT – hex, 3/4 inch NC
22 496-31081 2 WASHER – flat, 13/16 x 1-1/2 x 7/32 inch, hardened
23 426-12144 2 BOLT – hex, 3/4 NC x 9 inch, grade 8
24 90-7628T91 1 SHAFT ASSEMBLY – drive, intermediate shaft to rear axle (8C), parts list Figures 6-128 and 6-130
25 90-1902T93 1 SHAFT ASSEMBLY – drive, front axle to transmission, parts list Figure 6-128, Power Shift
25 90-7691T91 1 SHAFT ASSEMBLY – drive, front axle to transmission, parts list Figure 6-130, Synchroshift
26 90-7376T91 1 SHAFT ASSEMBLY – drive, intermdiate transmission to hanger bearing, parts list Figures 6-128 and
3 2-3842T1 1 SEAL – shaft retainer
4 1-9994T3 1 SPIDER – shaft, 8C
5 428-832 8 BOLT – hex, 1/2 NF x 2 inch, grade 8
9 90-7378T1 1 BEARING – block, shaft, P/N 90-7628T91 does not include bearing block and grease fitting, Ref. 9 and
10 219-1 1 FITTING – grease, straight, 1/8 PT x 21/32 inch, P/N 90-7628T91 does not include bearing block and
11 90-7379T1 1 YOKE – shaft
12 396-11131 1 WASHER – flat, 1-5/16 x 2-1/2 x 9/64 inch, hardened
13 131-487 1 NUT – heavy hex, self-locking, 1-1/4 – 18 inch
16 1-9994T3 1 SPIDER – shaft, 8C
17 428-832 8 BOLT – hex, 1/2 NF x 2 inch, grade 8
23 2-3842T1 1 SEAL – shaft retainer
24 1-9994T3 2 SPIDER – shaft, 8C
25 428-832 8 BOLT – hex, 1/2 NF x 2 inch, grade 8
30 2-3842T1 1 SEAL – shaft retainer
31 1-9994T3 2 SPIDER – shaft, 8C
32 428-832 8 BOLT – hex, 1/2 NF x 2 inch, grade 8
3 2-3842T1 1 SEAL – shaft retainer
4 1-9994T3 1 SPIDER – shaft, 8C
5 428-832 8 BOLT – hex, 1/2 NF x 2 inch, grade 8
9 90-7378T1 1 BEARING – block, shaft, P/N 90-7628T91 does not include bearing block and grease fitting, Ref. 9 and
10 219-1 1 FITTING – grease, straight, 1/8 PT x 21/32 inch, P/N 90-7628T91 does not include bearing block and
11 90-7379T1 1 YOKE – shaft
12 396-11131 1 WASHER – flat, 1-5/16 x 2-1/2 x 9/64 inch, hardened
13 131-487 1 NUT – heavy hex, self-locking, 1-1/4 – 18 inch
16 1-9994T3 1 SPIDER – shaft, 8C
17 428-832 8 BOLT – hex, 1/2 NF x 2 inch, grade 8
23 2-3842T1 1 SEAL – shaft retainer
24 1-9994T3 2 SPIDER – shaft, 8C
25 428-832 8 BOLT – hex, 1/2 NF x 2 inch, grade 8
30 2-3842T1 1 SEAL – shaft retainer
31 1-9994T3 2 SPIDER – shaft, 8C
32 428-832 8 BOLT – hex, 1/2 NF x 2 inch, grade 8
1 60-4269T1 1 STRIP – wear, lever
2 231-1445 2 NUT – hex, self-locking, 5/16 inch NC
3 225-14104 2 NUT, #4-40
4 231-1444 1 NUT, LOCK, 1/4″-20, GB
5 111626C1 2 NUT – hex, self-locking, special, 1/4 inch NC
6 426-412 1 BOLT – hex, 1/4 NC x 3/4 inch, grade 8
7 60-4270T1 1 BRACKET – support, console to mounting bracket
8 60-5608T1 1 BRACKET – micro switch mounting
9 20-2333T1 1 SWITCH – micro
10 470-10428 2 SCREW – machine, pan head slotted, No. 4 NC x 1-3/4 inch
11 86632551 6 NUT, LOCK, #10-24, GB
12 60-4272T1 1 KNOB – lever, PTO actuating
13 19-5798 1 SCREW – set, No. 8 NC
14 60-4265T2 1 LEVER – actuating, PTO
15 60-4296T2 1 BRACKET – cable actuating
16 496-21053 3 WASHER – flat, 17/32 x 1-1/16 x 1/8 inch, hardened
17 60-5858T1 1 BRACKET – mounting, PTO controls
20 231-1448 1 NUT – hex, self-locking, 1/2 inch NC
21 90-4367T1 2 BUSHING – pivot
22 60-4294T1 1 SPRING – tension
23 60-4293T1 1 TRUNNION – lever
24 60-6066T1 1 SEAL – foam, cab floor to cable
25 60-5020T1 1 BRACKET – cable mounting
26 426-512 2 BOLT – hex, 5/16 NC x 3/4 inch, grade 8
27 19-5777 2 NUT – hex, special
28 60-5021T1 1 SPACER – rod end
29 A146456 1 JOINT – ball, 1/4 inch NF, cable, PTO
30 426-424 1 BOLT – hex, 1/4 NC x 1-1/2 inch, grade 8
31 495-31022 2 WASHER, #10
32 60-5726T1 1 CABLE – actuating, PTO
33 60-6240T1 1 YOKE – cable
34 90-8047T1 1 GUARD – cable
38 425-1512 1 NUT – hex, jam, 3/4 inch NF
39 19-6041 1 PIN – headless
40 32-212 2 PIN, SPLIT (COTTER), 1/32″ x 3/4″
43 90-8048T1 1 RETAINER – cable guard
44 458-412 2 BOLT – hex flange, 1/4 NC x 3/4 inch
45 60-5609T1 1 SPACER – switch mounting
46 425-114 2 NUT, 1/4″-28, G5
47 515-23127 1 CLAMP – P-type, 1/2 inch ID, tube
48 425-105 1 NUT – hex, 5/16 inch NC
1 90-7517T1 1 SLEEVE – drive coupling
2 33-1467T1 2 PIN – dowel
4 SM922247 1 RING – snap
5 33-1528T1 1 ADAPTER – pump drive, used only when equipped with PTO, See Figure 6-006 for adapter used on
6 33-1446T1 1 RING – snap
7 SM8124280 4 BOLT – hex, 12 – 1.25 x 95 mm
8 SM8124290 8 BOLT – hex, 12 – 1.25 x 90 mm
8 SM8124295 2 BOLT – hex, 12 – 1.25 x 95 mm
8 SM8124285 1 BOLT – hex, 12 – 1.25 x 85 mm
10 50-1388T2 1 GASKET – pump
11 SM8124460 2 BOLT – hex, 8 – 1.50 x 60 mm
12 SM8915342 3 WASHER – lock, 12 mm
13 895-11012 3 WASHER – flat, 13.5 x 24 x 2.5 mm
15 90-7045T93 1 CLUTCH ASSEMBLY – PTO, parts list Figures 6-132 – 6-138
16 33-1524T91 1 PUMP ASSEMBLY – transmission lubrication, parts list Figure 6-030
17 892-11014 4 WASHER – lock, 14 mm
18 SM8911244 2 NUT – hex, 14 mm – 1.5
19 33-1452T1 1 COUPLING – pump
20 33-1445T1 1 RING – snap
25 90-7045T93 1 CLUTCH ASSEMBLY – PTO, parts list Figures 6-136 – 6-142, synchroshift tractors
26 33-1467T1 2 PIN – dowel, synchroshift tractors
29 SM8124295 2 BOLT – hex, 12 – 1.25 x 95 mm, synchroshift tractors
30 SM8124290 10 BOLT – hex, 12 – 1.25 x 90 mm, synchroshift tractors
31 SM8124285 1 BOLT – hex, 12 – 1.25 x 85 mm, synchroshift tractors
32 SM8124280 1 BOLT – hex, 12 – 1.25 x 95 mm, synchroshift tractors
33 SM8915342 5 WASHER – lock, 12 mm, synchroshift tractors
34 895-11012 5 WASHER – flat, 13.5 x 24 x 2.5 mm, synchroshift tractors
1 S8540S01F 1 GASKET – servo housing, Part of PTO clutch overhaul kit P/N S9870S01F.
2 S8530S00F 1 HOUSING – PTO servo
3 S1030S00F 3 PLUG – hex, O-ring boss, Includes: Ref. 4
4 S1040S00F 3 O-RING – plug, Part of PTO clutch overhaul kit P/N S9870S01F.
5 S8550S00F 1 PLUG – O-ring boss, Includes: Ref. 6
6 S8560S00F 1 O-RING – plug
7 STX99700F 2 PLUG – orifice
8 SM8124030 6 BOLT – hex, 10 mm – 1.25 x 30 mm
9 892-11010 3 WASHER – lock, 10 mm
10 SM8124080 3 BOLT – hex, 10 mm – 1.25 x 80 mm
11 S9510S01F 1 GASKET – control valve, replaces S9510S00F gasket
12 S9500S00F 1 VALVE ASSEMBLY – PTO control, parts list Figure 6-142
15 S1390S00F 2 PLUG – O-ring boss, Includes: Ref. 16
16 S1320S00F 2 O-RING – plug
17 SM8120880 4 BOLT – hex, 8 mm – 1.25 x 80 mm
18 90-7005T1 1 YOKE – PTO output, Includes: Ref. 19
19 S8950S00F 1 O-RING – yoke seal
21 S8930S00F 1 PLUG – orifice
22 S8920S00F 1 PLUG – orifice
24 S8860S00F 1 WASHER – flat
25 514-1021 1 Bolt, Hex, M16 x 1.5 x 35, 10.9, Full Thd, Replaces SM8134635 bolt
26 90-7519T1 1 COVER – lubrication pump
35 SM8267455 2 STUD – 14 – 1.5 x 55 mm
38 50-1388T2 1 GASKET – pump
1 S8740S00F 1 HUB – clutch brake
2 S8820S00F 1 SEAL – oil
3 S2630S00F 1 RING – sealing
4 S8850S00F 1 O-RING – hub seal
5 S8520S02F 1 HOUSING – PTO
6 S8840S00F 6 BOLT – socket head, special
7 S8960S00F 1 RING – sealing
8 S8750S00F 1 PISTON – brake
9 S8890S00F 3 PIN – guide
10 S8910S00F 3 SPRING – compression
13 S9900S00F 3 WASHER – spring retaining
14 S9890S00F 3 PIN – roll
15 S8900S00F 3 O-RING – seal
17 SM8911040 3 NUT – slotted, 10 mm – 1.5
18 SM9212221 3 PIN – cotter
19 S2080S00F 2 PLATE – steel, 2.4 mm thick
20 33-1518T2 1 PLATE – friction
23 SM3272036 1 BALL – steel
24 S8760S00F 1 PLATE – reaction
25 S8770S00F 1 RING – retaining
26 S8790S00F 1 SHAFT – output
27 S2240S00F 2 RING – retaining
28 S8780S00F 1 GEAR – driven
29 ST293 1 BEARING – ball
30 33-1467T1 2 PIN – dowel
33 S8510S03F 1 COVER – PTO
34 SM8124280 3 BOLT – hex, 12 – 1.25 x 95 mm
35 SM8124285 1 BOLT – hex, 12 – 1.25 x 85 mm
36 S8810S00F 1 BEARING – ball
37 S8970S00F 1 WASHER – bearing spacer
38 S8980S00F 1 RING – retaining
39 S9990S00F 1 SHIM – bearing retainer
40 S8990S00F 1 RETAINER – bearing
41 SM8120830 10 BOLT – hex, 8 – 1.25 x 30 mm
45 S8570S00F 1 RETAINER – shaft
46 SM8124230 1 BOLT – hex, 12 – 1.25 x 30 mm
48 S8590S00A 1 PACK ASSEMBLY – clutch, PTO, replaced by S8590S01A pack, parts list Figure 6-140
48 S8590S01A 1 PACK ASSEMBLY – clutch, PTO, replaces S8590S00A pack, parts list Figure 6-140
49 SM8915342 5 WASHER – lock, 12 mm
50 895-11012 5 WASHER – flat, 13.5 x 24 x 2.5 mm
51 SM8124290 10 BOLT – hex, 12 – 1.25 x 90 mm
52 895-11012 10 WASHER – flat, 13.5 x 24 x 2.5 mm
16 895-11010 3 WASHER – flat, 11 x 20 x 2 mm
1 S8610S01A 1 SHAFT – input, PTO, replaces S8610S00A shaft
2 SM3272036 1 BALL – steel
3 S2610S00F 1 RING – piston
4 S9190S00F 1 PLATE – reaction
5 S2630S00F 1 RING – sealing
6 S2240S00F 1 RING – retaining
7 S8730S00F 2 BEARING – roller
8 S3070S00F 2 RING – sealing, Part of PTO clutch overhaul kit P/N S9870S01F.
9 33-1526T1 1 PISTON – clutch
10 S2220S00F 2 WASHER – thrust, 2.4 mm
13 S2090S00F 8 PLATE – steel, 2.1 mm thick
14 33-1518T2 8 PLATE – friction
15 S8690S00F 12 SPRING – compression
16 S9850S00A 1 HUB – clutch
17 S2100S00F 1 RING – snap
18 H144527 2 WASHER – thrust, bearing, 3.2 mm, replaces S2200S00F washer
19 572182R1 2 BEARING – needle, thrust, replaces S2230S00F bearing
20 S2030S00F 1 BEARING – roller
21 S8700S00A 1 GEAR – drive
1 S9580S00F 1 BODY – modulator
2 S9720S00F 4 PLUG – pipe
4 S9730S00F 1 PLUG – orifice
5 S1390S00F 2 PLUG – O-ring boss
6 S1320S00F 2 O-RING – plug
7 S9610S00F 1 COVER – valve
8 S9620S00F 1 SPOOL – reducing, valve
9 S9640S00F 1 PIN – centering
10 S9650S00F 1 SPRING – compression
12 S9660S00F 1 O-RING – plug
13 S9670S00F 1 PLUG – O-ring boss
14 S9600S00F 1 GASKET – cover, Part of PTO clutch overhaul kit P/N S9870S01F.
15 S9590S00F 1 SPOOL – modulator
16 S9550S00F 1 COVER – control stem
17 S9540S00F 1 O-RING – seal
18 S9530S00F 1 SEAL – control stem
19 S9570S00F 1 GASKET – stem cover, Part of PTO clutch overhaul kit P/N S9870S01F.
20 S9520S00F 1 STEM – control
22 S9560S00F 1 SPRING – compression
23 S9690S00F 2 BALL – steel
24 S9700S00F 2 SPRING – compression
25 S9710S00F 2 PLUG – hex
26 S9680S00F 8 BOLT – hex
1 90-7008T91 1 SHAFT ASSEMBLY – drive, PTO, parts list Figure 6-146
2 L116943 8 RETAINER – drive shaft
3 L116940 16 BOLT – 12-point, 3/8 NF x 3/4 inch, grade 8
4 90-7037T91 1 HANGER ASSEMBLY – drive shaft bearing, parts list Figure 6-146
5 50-3429T1 1 BRACKET – mounting, bearing
6 426-1048 4 BOLT – hex, 5/8 NC x 3 inch, grade 8
7 90-7383T91 1 SHAFT ASSEMBLY – drive, PTO rear, parts list Figure 6-146
8 425-1010 4 NUT, 5/8″-11, G5, Bracket mounting without PTO
9 496-21066 4 WASHER – flat, 21/32 x 1-5/16 x 5/32 inch, hardened
3 33-1001T1 1 SEAL – shaft retainer
4 S300313 2 SPIDER – shaft
5 S92378 4 RING – snap, not shown, only 2 required in this application
8 90-6446T1 1 HOUSING – hanger bearing
9 90-1930T1 1 SHAFT – drive, center
10 22396V 2 CUP – tapered roller bearing
11 25695HO 2 CONE – tapered roller bearing
12 90-1934T2 2 SEAL – grease
13 90-7006T1 2 YOKE – shaft
16 19-5864 2 WASHER – flat, 5/8 x 2-3/4 x 1/2 inch
17 426-1024 2 BOLT – hex, 5/8 NC x 1-1/2 inch, grade 8
18 219-1 1 FITTING – grease, straight, 1/8 PT x 21/32 inch
23 33-1001T1 1 SEAL – shaft retainer
24 S300313 2 SPIDER – shaft
25 S92378 4 RING – snap, not shown, only 2 required in this application
1 L33289 4 CONE – tapered roller bearing, 2-1/4 inch ID
2 90-1996T1 4 CUP – tapered roller bearing, replaces 105497H cup
3 90-4402T1 1 GEAR – output, 54 teeth
4 90-1173T1 2 KEY – shaft
5 90-4401T1 1 SHAFT – output
6 214389 1 PLUG, Hex Hd, 3/4″-16 ORB, Includes Ref. 7
7 237-6008 1 O-Ring, 8-1, 90 Duro, .644″ ID x .087″ Thk
10 1-2270 1 O-RING – end cap, 9-1/4 x 9-1/2 inch
14 90-4420T2 1 CAP – end, PTO output
15 426-824 8 BOLT – hex, 1/2 NC x 1-1/2 inch, grade 8
20 90-1995T1 1 SEAL – oil
23 90-4425T2 1 BUSHING – spacer, center shaft
24 90-3580T1 2 CONE – tapered roller bearing
25 90-3581T1 2 CUP – tapered roller bearing
26 90-3577T1 1 SPACER – gear, center shaft
27 90-4403T1 1 GEAR – center, 49 teeth
28 19-6058 1 RING – snap
31 90-4418T1 1 PIN – center shaft
32 90-4424T1 1 O-RING – seal, 2-3/8 x 2-5/8 inch
34 426-58 4 BOLT – hex, 5/16 NC x 1/2 inch, grade 8
35 90-4409T2 1 BAFFLE – oil
37 238-5132 1 O-RING – 1-3/4 ID x 3/32 inch wide, yoke
38 90-1991T1 1 SHAFT – input
39 90-4404T1 1 GEAR – input, 32 teeth
40 90-4423T1 1 O-RING – cap
41 90-4422T1 1 CAP – end, input shaft
46 238-5132 1 O-RING – 1-3/4 ID x 3/32 inch wide
47 90-1994T1 1 SEAL – oil
48 90-7007T1 1 YOKE – input, PTO
49 19-5776 1 WASHER – flat
50 426-1024 1 BOLT – hex, 5/8 NC x 1-1/2 inch, grade 8
53 218-5106 1 ELBOW – 90 degree, 3/4-16 inch flare x adj O-ring boss, Includes: Ref. 54
54 237-6008 1 O-Ring, 8-1, 90 Duro, .644″ ID x .087″ Thk
57 37-1420 1 PIN – dowel, 1/4 x 1-1/4 inch, hardened, replaces 37-1420 pin
58 90-4417T3 1 HOUSING – transfer case, PTO
59 90-5870T1 1 MOUNT – shield, left-hand
60 90-5869T1 1 MOUNT – shield, right-hand
70 495-11041 4 WASHER – flat, 13/32 x 13/16 x 1/16 inch
71 231-1446 4 NUT, LOCK, 3/8″-16, GB
72 19-6013 4 SPACER – pivot
73 426-620 4 BOLT – hex, 3/8 NC x 1-1/4 inch, grade 8
74 90-5868T1 1 BRACKET – mounting, shield
75 90-3484T1 1 SHIELD – PTO
76 90-5866T1 2 RETAINER – bracket
79 2-7125T1 1 DECAL – Warning, rotating driveline, replaced by 2-7125T2 Decal, Ref. 84
80 426-12112 2 BOLT – hex, 3/4 NC x 7 inch, grade 8, with three point hitch
81 426-12144 6 BOLT – hex, 3/4 NC x 9 inch, grade 8, with three point hitch
81 413-12128 6 BOLT – hex, 3/4 NC x 8 inch, without three point hitch
83 425-1012 6 NUT – hex, 3/4 inch NC
84 2-7125T2 1 DECAL – Warning, rotating driveline, replaces 2-7125T1 decal, Ref. 79
1 90-8099T1 2 PLATE – seal stripper
2 90-5988T1 2 SEAL – hub, includes wear sleeve
3 90-8088T1 2 RING – seal wear
4 1-6693 1 BREATHER – valve
5 90-8089T1 32 BOLT – hex, special
6 90-8090T1 2 SPINDLE – axle, front
7 90-8091T1 1 HOUSING – axle
8 90-4484T1 4 PLUG – magnetic, 24 mm – 1.5
9 90-8092T1 2 PIN – dowel, 10 x 24 mm
10 90-8093T1 2 NUT – slotted, adjusting
11 90-8094T1 2 WASHER – lock, adjusting nut
12 90-8095T1 2 RING – spacer
13 90-8096T1 2 BEARING – tapered roller
14 90-8097T1 2 HUB – wheel
15 90-8098T1 2 BEARING – tapered roller
17 90-8391T1 1 PLUG – hex
18 429-1016 16 NUT – hex, 1 inch NC, grade 8
19 90-7493T1 8 BOLT – hex, 1 NC x 10 inch
20 90-8392T1 1 SEAL – oil
21 19-5739 1 WASHER – flat, special
1 90-8119T1 1 CARRIER – inner planetary
2 90-7832T1 220 NEEDLE – bearing, 44 per gear
3 90-8065T1 6 SHAFT – planetary pinion, with lube hole
3 90-8121T1 2 SHAFT – planetary pinion, without lube hole
4 90-8122T1 5 GEAR – pinion, inner planetary
5 16-1607 5 BALL – steel
6 90-8116T1 1 PLATE – baffle
7 90-8117T1 1 PLATE – oil
8 896-12006 2 WASHER – flat, 6.6 x 12.5 x 2 mm
9 627-6012 2 BOLT – hex, full threads, 6 – 1.0 x 12 mm, class 10.9
10 90-7837T1 5 RING – bearing seat
11 16-1626 3 BOLT – hex, 8 x 15 mm, grade 10.9
12 90-8110T1 10 PLATE – thrust
13 90-8115T1 2 GEAR – ring
14 90-8100T1 1 RING – snap
15 90-8101T1 1 GEAR – sun
16 90-8102T1 1 SHAFT – axle, 1151 mm long
16 90-8103T1 1 SHAFT – axle, 1199 mm long
17 90-4484T1 1 PLUG – magnetic, 24 mm – 1.5
18 90-8104T1 1 COVER – axle end
19 90-8105T1 1 PIN – support, axle shaft
20 90-8106T1 1 GEAR – double ring
21 90-7371T1 31 BOLT – flange, 14 mm – 1.5 x 45 mm, grade 10.9
31 90-8108T1 1 CARRIER – outer planetary
32 90-8110T1 6 PLATE – thrust
33 90-7832T1 132 NEEDLE – bearing, 44 per gear
34 90-8111T1 3 GEAR – pinion, outer
35 16-1607 3 BALL – steel
36 90-8113T1 1 GEAR – sleeve
37 90-8109T1 1 DOWEL – pin
38 90-4528T1 1 RING – snap
39 90-8114T1 1 GEAR – sun
40 16-1623 1 RING – snap
41 90-8065T1 3 SHAFT – planetary pinion, with lube hole
42 90-7837T1 3 RING – bearing seat
1 90-2509T2 1 SEAL – oil
2 614-8030 6 HH, CL 8.8, M8 x 1.25 x 30
3 90-4517T1 1 COVER – seal retainer
4 16-1582 1 BEARING – tapered roller
5 90-4515T1 1 HOUSING – bearing
6 16-1621T1 12 BOLT – hex flange, 14 – 1.5 x 45 mm, grade 10.9
9 90-4503T1 1 SLEEVE – bearing spacer
10 16-1565 1 BEARING – tapered roller
11 90-8080T91 1 GEAR – set, ring and pinion, rear axle, replaces 90-8080T1 gear, Includes: Ref. 12 & 13, P/N
11 90-8081T91 1 GEAR – set, ring and pinion, front axle, replaces 90-8081T1 gear, Includes: Ref. 12 & 13, P/N
12 16-1589 1 NUT – hex slotted, special, P/N 90-8080T1, 90-8080T91 and 90-8081T1 gear assemblies also include
13 432-1640 1 Pin, Split (Cotter), 1/4″ x 2 1/2″, P/N 90-8080T1, 90-8080T91 and 90-8081T1 gear assemblies also
14 90-8437T91 1 HOUSING ASSEMBLY – differential, includes both halves, replaces 90-8132T91 housing, Includes:
15 90-8077T1 12 BOLT – hex flange, special
16 90-8087T1 2 BOLT – hex socket, special
17 90-8134T1 12 BOLT – hex, special, P/N 90-8080T1, 90-8080T91 and 90-8081T1 gear assemblies also include (12)
18 90-8435T1 4 WASHER – thrust, 1.5 mm, pinion gear
19 90-7856T1 4 GEAR – pinion
20 90-8078T1 1 SPIDER – gear
21 90-8079T1 2 GEAR – pinion, axle drive
22 90-8439T1 2 WASHER – pinion gear
23 90-7870T1 116 NEEDLE – bearing, 29 per gear
24 16-1546 6 PLATE – bolt retaining, P/N 90-8080T1, 90-8080T91 and 90-8081T1 gear assemblies also include (12)
25 90-7824T1 1 YOKE – flanged, 8C, use with front axle, shown on Figure 6-156
25 90-7822T1 1 YOKE – 8C, use with rear axle, not shown
26 16-1626 4 BOLT – hex, 8 x 15 mm, grade 10.9
27 90-8130T91 1 CARRIER ASSEMBLY – housing, front or rear, Includes: Ref. 28 & 29
28 90-7138T1 2 BOLT – hex flange, special
29 90-8162T1 2 PIN – dowel
30 90-8277T1 1 BEARING – tapered roller
32 A48105 1 BEARING – tapered roller
33 90-8068T1 2 NUT – bearing retainer
34 90-7230T1 1 NUT – bearing retainer
36 16-1524 2 PLATE – locking
37 90-7371T1 20 BOLT – flange, 14 mm – 1.5 x 45 mm, grade 10.9
2 614-8030 1 HH, CL 8.8, M8 x 1.25 x 30
3 90-4517T1 6 COVER – seal retainer
4 16-1582 1 BEARING – tapered roller
5 90-4515T1 1 HOUSING – bearing
6 16-1621T1 1 BOLT – hex flange, 14 – 1.5 x 45 mm, grade 10.9
9 90-4503T1 1 SLEEVE – bearing spacer
10 16-1565 1 BEARING – tapered roller
11 90-8080T91 1 GEAR – set, ring and pinion, rear axle, replaces 90-8080T1 gear
11 90-8081T91 1 GEAR – set, ring and pinion, front axle, replaces 90-8081T1 gear
12 16-1589 1 NUT – hex slotted, special
13 432-1640 1 Pin, Split (Cotter), 1/4″ x 2 1/2″
29 90-8436T91 1 HOUSING ASSEMBLY – differential, replaces 90-8075T91 housing, Includes: Ref. 30
30 90-8077T1 12 BOLT – hex flange, special
31 90-8087T1 2 BOLT – hex socket, special
32 90-8082T1 12 BOLT – hex flange, special
33 90-8435T1 4 WASHER – thrust, 1.5 mm, pinion gear
34 90-7856T1 4 GEAR – pinion
35 90-8078T1 1 SPIDER – gear
36 90-8079T1 2 GEAR – pinion, axle drive
37 90-8439T1 2 WASHER – pinion gear, thrust
38 90-7870T1 116 NEEDLE – bearing, 29 per gear
39 16-1546 6 PLATE – bolt retaining
40 90-8076T1 1 HOUSING – half, flanged
41 90-8086T1 1 WASHER – thrust
42 90-8084T1 1 HUB – splined
43 33-1230T1 1 SPRING – compression
44 90-8085T1 1 WASHER – thrust
45 33-1493T1 8 DISK – inner
46 33-1494T1 9 DISK – outer
47 33-1278T1 1 BUSHING – clutch alignment
48 90-8083T1 1 SLEEVE – clutch
49 90-7824T1 1 YOKE – flanged, 8C, use with front axle
49 90-7822T1 1 YOKE – 8C, use with rear axle, not shown
52 90-8069T1 1 FORK – shift, traction control
53 33-1290T1 2 PIN – thrust
54 90-8070T1 1 BOLT – hex, special
55 90-8071T1 1 NUT – hex, special
56 90-8072T1 1 SHAFT – shift fork
57 90-8073T1 2 PLUG – cap
58 90-7151T1 2 STUD – shift fork
59 33-1294T1 2 WASHER – flat, special
60 90-7152T1 2 NUT – hex, lock, special
61 90-8068T1 2 NUT – bearing retainer
62 90-7230T1 1 NUT – bearing retainer
64 16-1524 2 PLATE – locking
65 90-8064T91 1 HOUSING ASSEMBLY – differential, Includes: Ref. 66 & 67
66 90-7138T1 2 BOLT – hex flange, special
67 90-8162T1 2 PIN – dowel
68 L35045 1 BEARING – tapered roller
69 L30842 1 CUP – tapered roller bearing
70 A48105 1 BEARING – tapered roller
71 90-7371T1 20 BOLT – flange, 14 mm – 1.5 x 45 mm, grade 10.9
72 16-1626 4 BOLT – hex, 8 x 15 mm, grade 10.9
1 218-441 1 ADAPTER – straight, 7/16-20 flare x 1/8 inch PT
3 18-1537 1 HOSE – 1143 mm (45 inch) long
4 218-1022 1 ADAPTER – straight, 7/16-20 flare x 1/4 inch PT
5 116195A1 1 VALVE – check
6 31-3069 1 ADAPTER – axle cooling
7 217-1034 1 REDUCER, 1/4″-18 Male NPTF x 1/8″-27 Female NPTF
8 1964960C1 1 SWITCH – axle cooling
9 31-2685 1 ADAPTER – orfice
10 31-3068 1 HOSE – axle cooling
11 218-453 1 ADAPTER – straight, 9/16-18 flare x 1/8 inch PT
12 19-135 6 STRAP – tie, nylon
13 515-23238 1 CLAMP – P-type, 15/16 inch ID
14 218-5107 1 ELBOW – 90 degree, 7/8-14 inch flare x adj O-ring boss, Includes: Ref. 14A
15 31-3067 1 HOSE – axle cooling
16 218-485 1 ELBOW – 90 degree, 7/8-14 flare x 1/2 inch PT
17 231-1445 2 NUT – hex, self-locking, 5/16 inch NC
18 R15257 2 CLAMP – hose
19 426-532 1 BOLT – hex, 5/16 NC x 2 inch, grade 8
20 218-5058 1 ADAPTER – straight, 9/16-18 flare x 3/4-16 inch O-ring boss, Includes: Ref. 21
21 237-6008 1 O-Ring, 8-1, 90 Duro, .644″ ID x .087″ Thk
22 218-5283 2 ELBOW – 90 degree, 7/16-20 flare x 9/16-18 inch adj O-ring boss, Includes: Ref. 22A
23 31-3072 2 HOSE – 1168 mm (46 inch) long, replaces 31-2477 hose
24 218-1575 1 TEE – 3/4-16 flare branch x 9/16-18 inch flare x flare
25 31-2908 1 HOSE – lube
26 218-5106 1 ELBOW – 90 degree, 3/4-16 inch flare x adj O-ring boss, Includes: Ref. 27
27 237-6008 2 O-Ring, 8-1, 90 Duro, .644″ ID x .087″ Thk
28 50-3580T1 1 BRACKET – valve
29 231-1444 2 NUT, LOCK, 1/4″-20, GB
30 426-432 2 BOLT – hex, 1/4 NC x 2 inch, grade 8
31 515-23190 1 CLAMP – P-type, 3/4 inch ID
32 218-980 1 ELBOW – 90 degree, 9/16-18 inch flare x swivel
33 31-3070 2 ADAPTER – orifice
34 1260819C91 1 VALVE – control, Includes: Ref. 35 – 39
35 149944C91 1 VALVE ASSEMBLY – solenoid, Includes: kit
40 31-3058 1 HOSE – 508 mm (20 inch) long, replaces 31-2067 hose
1 218-441 1 ADAPTER – straight, 7/16-20 flare x 1/8 inch PT
2 218-786 2 ADAPTER – reducing, 3/4-16 female str thread x 9/16-18 inch flare
3 18-1537 1 HOSE – 1143 mm (45 inch) long
4 218-1022 1 ADAPTER – straight, 7/16-20 flare x 1/4 inch PT
5 116195A1 1 VALVE – check
6 31-3069 1 ADAPTER – axle cooling
7 217-1034 1 REDUCER, 1/4″-18 Male NPTF x 1/8″-27 Female NPTF
8 1964960C1 1 SWITCH – axle cooling
9 31-2685 1 ADAPTER – orfice
10 31-3186 1 HOSE – axle cooling
11 218-453 1 ADAPTER – straight, 9/16-18 flare x 1/8 inch PT
12 19-135 6 STRAP – tie, nylon
13 515-23238 1 CLAMP – P-type, 15/16 inch ID
14 218-5107 1 ELBOW – 90 degree, 7/8-14 inch flare x adj O-ring boss, Includes: Ref. 14A
Pages: 1 2 3 4

Leave a Reply

Your email address will not be published. Required fields are marked *