CASE IH Axial – Flow Combine 1666

admin October 16, 2016 No Comments

CASE IH Axial – Flow Combine 1666 — parts list, part 1 of 6

4,521 part numbers across 1 assemblies, transcribed from the catalogue above and split over 6 pages. Search a page for a part number to find the assembly it belongs to; the page links are below the list.

Parts list

Pos	Part no.	Qty	Description
1	A189067	1	RADIATOR, cooling system
2	A170241	1	CAP, RADIATOR, 15 psi
3	106201A1	1	RING, ORIFICE, SHROUD fan, includes both halves, Includes: Ref. 4, 5, and 6
4	614-8025	4	BOLT, Hex, M8 x 25, 8.8
5	896-11008	8	WASHER, M8 x 17.5 x 2, HT, flat, 9 x17 x 2 mm, hardened
6	832-41308	4	NUT, M8 x 1.25, Cl 10, hex, self-locking 8 mm – 1.25, class 10.9
7	1970457C2	1	SEAL, 31 inch (787 mm) long, cut from 1974883CX bulk seal radiator to shroud, upper, see below
8	1979476C1	1	SEAL, 28-3/4 inch (730 mm) long, cut from 1974883CX bulk seal radiator to shroud, lower, see below
9	409-7512	8	BOLT, Hex Flg, 5/16″-18 x 3/4″, Serr
10	495-81001	8	WASHER, 5/16″, flat, 3/8 x 1-1/8 x 1/16 inch
11	492-11031	8	WASHER, LOCK, 5/16″, If used
12	488837C1	8	NUT, speed, 5/16 inch NC, replaces 131-636
13	1970536C1	2	SEAL, foam, adhesive backed 34-1/2 inch (875 mm) long, cut from 195917C1 bulk seal radiator to air
14	86982771	1	VALVE, drain, 1/4 inch PT
15	R29799	2	SHOCK ABSORBER, INSULATOR rubber, radiator mounting
16	434-736	2	BOLT, CARRIAGE, Short NK, 7/16″-14 x 2 1/4″, G5
17	495-81013	4	WASHER, .469″ x 1 3/4″ x .120″
18	231-1447	2	NUT, LOCK, 7/16″-14, GB
19	1329863C1	1	SUPPORT, radiator, left hand
20	1541868C1	1	SUPPORT, radiator, right hand
21	154273C1	2	BOLT, Hex Flg, 3/8″-16 x 1″, Serr, BOLT hex, self-locking, special, 3/8 NC x 1 inch
22	231-5146	2	NUT, Flg, USR, 3/8″-16
23	199953C1	2	SCREW, SELF TAPPING, Hex Wash Hd, 5/16″-18 x 13/16″
24	492-11031	2	WASHER, LOCK, 5/16″
25	495-81001	2	WASHER, 5/16″, flat, 3/8 x 1-1/8 x 1/16 inch
26	84549C2	1	HOSE, LARGE, engine outlet, upper, radiator
27	214-3240	2	CLAMP, HOSE, 1.75/2.625 HD Worm, W/liner, Adj.
28	1979382C1	1	HOSE, LARGE, engine inlet, radiator, lower
29	214-3248	2	CLAMP, HOSE, 2.25/3.125 HD Worm, W/liner, Adj.
30	217-151	1	FITTING, 3/8″ Hose X 1/4″ NPTF Beaded, Adapter – straight, Radiator top tank vent
31	1960764C1	1	HOSE, 22 inch (560 mm) long, radiator vent to engine
32	214-1706	2	CLAMP, HOSE, #6, 0.44/0.78 Type M Worm, Adjustable
1	A189067	1	RADIATOR, cooling system, for mounting, see Fig. 2-2, coolant recovery system
2	437703C2	1	TANK, RESERVOIR coolant recovery system
3	437702C1	1	CAP, reservoir tank, coolant recovery system
4	1347455C1	1	HOSE, LARGE, 46-1/2 inch (1180 mm) long, reservoir to radiator, coolant recovery system
5	214-1704	2	CLAMP, HOSE, #4, 0.25/0.62 Type M Worm, Adjustable, Coolant recovery system
6	409-7416	3	BOLT, Hex Flg, 1/4″-20 x 1″, Serr, Coolant Recovery System
7	495-81109	3	WASHER, .281″ x 1″ x .048″, flat, 9/32 x 1 x 3/64 inch, coolant recovery system
8	231-5144	3	NUT, Flg, USR, 1/4″-20, Coolant recovery system
11	1977159C1	1	SUPPORT, baffle, left hand, rotary air screen baffle seals
12	1977160C1	1	SUPPORT, baffle, right hand, rotary air screen baffle seals
13	1977161C1	1	SUPPORT, baffle, left hand rear, rotary air screen baffle seals
14	1977162C1	1	SUPPORT, baffle, right hand rear, rotary air screen baffle seals
17	1977163C1	2	PLATE, LARGE, STRIP, 11-13/16 inch (300 mm) long, baffle side, rotary air screen baffle seals
18	1977164C1	2	STRIP, 6-1/2 inch (165 mm) long, baffle rear, rotary air screen baffle seals
19	1977165C1	2	SEAL, 12 inch (304 mm ) long, baffle, rotary air screen baffle seals
20	1977166C1	2	SEAL, 8 inch (203 mm) long, baffle, rotary air screen baffle seals
21	409-748	12	BOLT, Hex Flg, 1/4″-20 x 1/2″, Serr, Rotary air screen baffle seals
22	231-4144	12	NUT, LOCK, 1/4″-20, GB, Rotary air screen baffle seals
23	194224C1	1	BAFFLE ASSY., rotary air screen, parts list Fig. 2-8, Ref. 6, rotary air screen baffle seals
1	1345399C1	1	FAN, BLADE cleaning
2	559205R91	1	BEARING, blade
3	1345404C1	1	SUPPORT, BRACKET mounting, blade, cleaning
4	409-7516	2	BOLT, Hex Flg, 5/16″-18 x 1″, Serr
5	495-81253	4	WASHER, .344″ x 7/8″ x 120″, flat, 11/32 x 7/8 x 1/16 inch
6	231-5145	2	NUT, Flg, USR, 5/16″-18
7	1345403C1	2	SUPPORT, adjustable, wiper blade
8	409-7516	2	BOLT, Hex Flg, 5/16″-18 x 1″, Serr
9	409-7520	4	BOLT, Hex Flg, 5/16″-18 x 1 1/4″, Serr, BOLT hex serrated flange, 5/16 NC x 1-1/4 inch
10	495-81253	8	WASHER, .344″ x 7/8″ x 120″, flat, 11/32 x 7/8 x 1/16 inch
11	231-5145	6	NUT, Flg, USR, 5/16″-18
1	1957272C2	1	FAN, rotary air screen
2	1347255C1	1	SHAFT, fan, rotary air screen
3	1317755C4	1	SUPPORT, rotary air screen, replaced by 1317755C6
4	256873	17	BOLT, Hex Flg, 5/16″-18 x 1/2″, Serr
4	409-7516	2	BOLT, Hex Flg, 5/16″-18 x 1″, Serr
5	231-5145	19	NUT, Flg, USR, 5/16″-18
6	194224C1	1	BAFFLE ASSY., rotary air screen
7	151-558	3	RIVET, Pop, 3/16″ x .450″, break mandrel, 3/16 x 1/2 inch
8	104235	4	RIVET, FH, 3/16″ x 1/2″
9	194226C2	1	SUPPORT, bearing, lower
10	477-82508	8	SCREW, Sltd Serr Truss Hd, 1/4″-20 x 1/2″, slotted truss head, 1/4 NC x 1/2 inch
11	231-5144	8	NUT, Flg, USR, 1/4″-20
12	194221C2	2	STAY, SUPPORT bearing, upper
13	477-73112	4	BOLT, Slotted Tr Hd, 5/16″-18 x 3/4″
14	231-5145	4	NUT, Flg, USR, 5/16″-18
15	164605C1	1	PLATE, LARGE, SUPPORT bearing flange, rear
16	164604C1	1	BAR, SUPPORT bearing flange, front
17	434-512	4	BOLT, CARRIAGE, Short NK, 5/16″-18 x 3/4″, G5, Full Thd
18	495-81112	4	WASHER, .344″ x 3/4″ x .120″, flat, 11/32 x 3/4 x 7/64 inch
19	492-11031	4	WASHER, LOCK, 5/16″
20	425-105	4	NUT, 5/16″-18, G5
21	455957R92	2	BEARING, ball, shaft, rotary air screen
22	455958R11	2	COLLAR, lock, bearing
23	H333534	4	FLANGE, bearing
24	477-73112	6	BOLT, Slotted Tr Hd, 5/16″-18 x 3/4″
25	231-5145	6	NUT, Flg, USR, 5/16″-18
26	1977217C1	1	SIEVE, ASSEMBLY rotary screen, fine
27	231-5144	12	NUT, Flg, USR, 1/4″-20
28	477-82508	12	SCREW, Sltd Serr Truss Hd, 1/4″-20 x 1/2″, slotted truss head, 1/4 NC x 1/2 inch
29	151-218	12	RIVET, Tr Hd, 3/16″ x .281″, Alum.
30	413-68	2	BOLT, Hex, 3/8″-16 x 1/2″, G5, Full Thd
31	492-11038	2	WASHER, LOCK, 3/8″
32	1338011C1	1	RING, RETAINER brush seal
33	201946C1	12	RIVET, Pop, 3/16″ x .325″, mandrel, steel, 3/16 diameter x 1/4 inch
34	164615C92	1	BRUSH, ASSEMBLY rotary air screen, includes ref. 35-37
35	164616C1	1	ANGLE, CLIP brush, short
36	164617C1	1	ANGLE, CLIP brush, long
37	470-11016	1	SCREW, Slotted Pan Hd, #10-24 x 1″, machine, pan head slotted, No. 10 NC x 1 inch
38	86625057	1	NUT, LOCK, #10-24, GB
39	495-11041	1	WASHER, 3/8″, SAE, Flat, (13/32 x 13/16 x 1/16″)
40	125-10002	1	NUT, 3/8″-16, G5, LH
41	632019R1	1	WASHER, LOCK, 3/8″, 3/8″, L.H. twist
42	1968544C2	1	SHAFT ASSY., rotary air screen fan
43	126-116	1	KEY, WOODRUFF, #9, 3/16″ x 3/4″, HT
44	1338442C1	1	HUB ASSY., rotary screen fan
45	409-7512	3	BOLT, Hex Flg, 5/16″-18 x 3/4″, Serr
46	231-5145	3	NUT, Flg, USR, 5/16″-18
1	1979861C2	1	TRAP DOOR, radiator access
2	477-73108	57	SCREW, Sltd Serr Truss Hd, 5/16″-18 x 1/2″, slotted truss head, 5/16 NC x 1/2 inch
3	231-5145	90	NUT, Flg, USR, 5/16″-18
4	1347459C2	1	SEAL, 36 inch (916 mm) long, radiator access door bottom
7	1979919C1	1	STEM, ROD door
8	1302494C2	1	LATCH, access door
9	1979856C2	1	DEFLECTOR, screen chute
10	1977122C7	1	CHUTE (DOWNWARD), air screen, upper
11	1970200C1	1	SUPPORT, deflector
12	199953C1	20	SCREW, SELF TAPPING, Hex Wash Hd, 5/16″-18 x 13/16″
13	495-61041	11	WASHER, 3/8″ x 1″ x .063″
14	1541788C3	1	SUPPORT, lower, rear, replaces 1541788C2
15	1979227C1	1	SHEET, SUPPORT screen chute, rear
16	1541858C2	1	SUPPORT, screen, upper, replaces 1541858C1
17	492-11031	5	WASHER, LOCK, 5/16″
18	1979854C1	1	SHEET ASSY., PANEL radiator inlet
19	1979853C2	1	CHUTE (DOWNWARD), bottom rear outlet
20	256873	13	BOLT, Hex Flg, 5/16″-18 x 1/2″, Serr
21	1317704C1	1	SUPPORT, top chute mounting
22	1979471C4	1	SUPPORT, radiator clean out
23	1302758C1	1	PLUG, plastic, 89 mm O.D., clean out hole, hinge
26	1315674C2	1	SUPPORT, chute, lower rear, corn and grain combines only
27	1968548C1	1	SUPPORT, BRACKET chute, discharge side
28	1979918C1	1	HANDLE, assist
29	495-81024	1	WASHER, 17/32″ x 1 1/4″ x .060″, flat, 17/32 x 1-1/4 x 1/16 inch
30	231-5148	6	NUT, Flg, USR, 1/2″-13
32	1347430C1	1	SUPPORT, BRACKET latch retainer, door
33	1968546C2	1	SUPPORT, discharge chute
34	1338012C1	1	BRUSH, block off
35	151-507	2	RIVET, Pop, 1/8″ x .575″, break mandrel, 1/8 x 1/2 inch
36	561915R1	1	BRACKET, bottom front, if used
37	477-73112	5	BOLT, Slotted Tr Hd, 5/16″-18 x 3/4″
38	1970461C1	2	GROMMET, rubber, 1-3/8 x 2 x 5/16 1-1/2 x 1-1/8 x 7/16 inch
39	256873	7	BOLT, Hex Flg, 5/16″-18 x 1/2″, Serr
41	1251832C2	1	HANDLE, assist
43	1315670C3	2	STRIP, SEALING, 29 inch (738 mm) long, radiator top and bottom, if used
44	1979728C2	1	SUPPORT, chute, lower rear, rice combines only
47	95-21044	3	WASHER, 3/8″, flat, 7/16 x 1 x 5/64 inch
48	437157R1	1	RING, SNAP, #37, Ext, #37, Ext
49	1347199C2	1	GUIDE, radiator door
50	205-82	2	BUTTON, HOLE PLUG, 13/32″, button, 13/32 inch ID, if used
50	205-77	2	BUTTON, HOLE PLUG, 11/32″, button, 11/32 inch ID
52	D81147	1	SPACER, 1/2 x 3/4 x 1-1/4 inch, door
52	D81147	1	SPACER, 1/2 x 3/4 x 1-1/4 inch, door
3	J902089	1	SEAL, pump to block
4	J900227	3	SCREW, Hex, M8 x 1.25 x 22
5	J910738	1	SUPPORT ASSY., fan, includes ref. 6-10
6	J907769	1	BOLT, hex, special, 10 – 1.5 x 70 mm, class 12.9
7	J923044	1	RETAINER, fan hub
8	100-21250	2	RING, SNAP, 2.50″, Int, #250
9	J910739	1	BEARING, BALL
10	J911924	1	HUB, fan
11	845-8050	4	BOLT, Hex Flg, M8 x 50, 8.8, Fan support to cylinder head
12	J914462	1	PULLEY, fan, 1.1 to 1 ratio
15	J925188	1	SUPPORT, BRACKET belt tensioner, replaces J911473
17	J925186	2	SCREW, COUNTERSUNK, Torx Soc, M8 x 1.25 x 25, flat head cap, torx, special, 8 – 1.25 x 25 mm
18	J918944	1	TENSIONER, belt
19	854-10075	1	BOLT, Hex Flg, M10 x 75, 10.9, BOLT heavy hex flange, 10 – 1.5 x 75 mm, class 10.9 belt tensioner
20	A77817	1	PACKAGE, REPAIR, KIT belt tensioner pulley, used to replace pulley of J918944, Ref. 18, Includes:
24	J911572	1	BELT, fan drive
25	A184548	1	SPACER, fan, 90 mm long
26	1547933C1	1	FAN, pulley, 650 mm O.D., part number stamped on fan blade
27	814-10130	4	BOLT, Hex, M10 x 130, 8.8
28	896-12010	4	WASHER, M10 x 21.5 x 2.5, HT, flat, 11 x 21 x 2.5 mm, hardened
29	96-81004	4	WASHER, 13/32″ x 1 1/4″ x .239″, HDN, flat, 13/32 x 1-1/4 x 15/64 inch, hardened
1	J924422	1	COVER ASSY, gear, front, BSN 45075642
3	J917779	1	GASKET, front gear cover
4	J917316	1	MOTOR HOUSING, gear, BSN 45075642
5	J281721	1	GASKET, housing, gear, BSN 45075642
6	J926863	6	BOLT, hex flange, 8 – 1.25 x 50 mm, class 10.9, replaces 845-8050
7	J924962	17	BOLT, hex flange, special, 8 – 1.25 x 16 mm, replaces 845-8016
8	J926846	5	BOLT, hex flange, 8 – 1.25 x 20 mm, class 10.9, replaces 845-8020
9	J900257	2	PIN, dowel, 16 mm long
10	J903463	1	COVER, front access
11	J903475	1	SEAL, front access cover
12	J914868	1	COVER, PLATE access cover, flat
13	J919601	1	GASKET, access cover plate
14	854-12025	2	BOLT, Hex Flg, M12 x 25, 10.9, Heavy
15	J919683	1	HOUSING, timing pin
16	J915772	1	SEALRING, quad, timing pin housing
17	J907998	2	SCREW, LOCK, Spc Rd Torx Hd, M5 x 17
18	J903924	1	PIN, timing
19	J913994	1	O-RING, sealing
20	J904849	1	RING, SNAP, 0.875″, Int, #87, Ring, Snap, 0.875″, Int, #87, timing pin
21	J906619	3	PLUG, hex, 1/8 inch PT
22	A77552	1	PLUG, expansion, 29/64 inch diameter
23	A77790	1	KIT, SEALS, oil seal, crankshaft front, Includes: Ref. 24-27
27	J918113	1	SHIELD, dust
2	627975C3	1	AIR CLEANER, ELEMENT primary , BSN JJC0106005
3	A44187	1	WASHER, sealing, primary element , BSN JJC0106005
4	627976C1	1	ELEMENT, secondary , BSN JJC0106005
5	A44187	1	WASHER, sealing, secondary element , BSN JJC0106005
6	L35499	2	NUT, wing, primary and secondary elements , BSN JJC0106005
7	1347839C1	1	COVER, ASSEMBLY air cleaner, end , BSN JJC0106005
8	A47102	1	NUT, wing, end cover , BSN JJC0106005
9	1541610C1	1	INDICATOR, air restriction, not shown , BSN JJC0106005
11	132151A1	1	ELEMENT, primary , ASN JJC0106005
12	132149A1	1	ELEMENT, secondary , ASN JJC0106005
13	134610A1	1	COVER, end, air cleaner , ASN JJC0106005
14	1541610C1	1	INDICATOR, air restriction , ASN JJC0106005
15	409-7612	4	BOLT, Hex Flg, 3/8″-16 x 3/4″, Serr, Air induction system
16	231-5146	4	NUT, Flg, USR, 3/8″-16, Air induction system
17	118094A1	1	HOSE, LARGE, turbo inlet, air induction system
18	214-3280	1	CLAMP, HOSE, 4.25/5.125 HD Worm, W/liner, Adjustable, Air Induction System
19	214-32112	1	CLAMP, HOSE, 6.25/7.125 HD Worm, W/liner, Air Induction System
20	217-15	1	ELBOW, 45є, 1/8″-27 NPTF, Fem x 1/8″-27 NPTF Male, ELBOW street, 45 degree, 1/8 inch PT x
21	117407A1	1	PRECLEANER, air induction, air induction system, During transport only, remove 117407A1
22	9-128	1	CAP, precleaner
1	185552A2	1	SOLENOID, ASSEMBLY ether injection, replaces A143381 and 185552A1
2	395686R1	1	GASKET, injector solenoid, 15/64 inch diameter, used with Ref. 1A only
3	121851C1	1	RETAINER, CONTAINER ether start fluid, used with Ref. 1A only
4	289970C91	1	FITTING, ELBOW 90 degree, special, 1/8-27 PT x 1/8 inch tube, used with Ref. 1A only
5	A172361	1	TUBE, 72 inch (1829 mm) long, cut from1954063CX bulk tube, solenoid to manifold, see this Figure
6	A172900	1	NOZZLE CAP, ASSEMBLY atomizer
7	217-40	1	REDUCER, 1/4″-18 NPTF x 1/8″-27 Fem NPTF, 1/4 PT x 1/8 inch PT, used with Ref. 1A only
8	477-73116	2	SCREW, Sltd Serr Truss Hd, 5/16″-18 x 1″, slotted truss head, 5/16 NC x 1 inch
9	495-81119	2	WASHER, .344″ x 1 1/4″ x .060″, flat, 11/32 x 1-1/4 x 1/16 inch
10	231-5145	2	NUT, Flg, USR, 5/16″-18
1	117424A1	1	HOSE, LARGE, 10 inch (254 mm) long, cut from 407001R1 bulk, exhaust aspirator, see this Figure
2	1275854C1	2	CLAMP, aspirator hose, if used
3	413-620	2	BOLT, Hex, 3/8″-16 x 1 1/4″, G5, Full Thd, hex, 3/8 NC x 1-1/4 inch, used with 1275854C1 clamp
4	492-11038	2	WASHER, LOCK, 3/8″, Used with 1275854C1 clamp
5	425-106	2	NUT, 3/8″-16, G5, Used with 1275854C1 clamp
6	1541960C2	1	CAP, exhaust pipe, weather, if used
7	116706A1	1	TUBE, exhaust aspirator top
8	1321280C2	1	CLAMP, exhaust pipe, elbow
9	409-7624	1	BOLT, Hex Flg, 3/8″-16 x 1 1/2″, Serr
11	231-5146	1	NUT, Flg, USR, 3/8″-16
12	116708A1	1	TUBE, exhaust aspirator, bottom
13	A170807	1	CLAMP, exhaust tube retaining
14	84569C5	1	ANGLE, BRACKET tube support, no longer available, order Ref. 14A, 84569C8
15	854-10020	2	BOLT, Hex Flg, M10 x 20, 10.9
16	495-81140	2	WASHER, 13/32″ x 1 1/4″ x .060″
17	S93558	1	U-BOLT, 3/8 inch NC
18	495-81140	2	WASHER, 13/32″ x 1 1/4″ x .060″
19	231-4116	2	NUT, LOCK, 3/8″-16, GB, hex, self-locking, 3/8 inch NC
20	214-1420	2	CLAMP, HOSE, #20, 0.81/1.75 Type F Worm, Adj., if used
1	J919199	1	TURBOCHARGER, ASSEMBLY engine, new, parts list Fig. 2-24
2	J905417	4	STUD, STUD turbocharger mounting, used with Ref. 3 nut only, if used
3	J901961	4	NUT, hex, special, 10 mm – 1.25, used with Ref. 2 stud only, if used
4	222-993	2	GASKET, 3/8 Tube, Fl, Copper
9	J911941	1	GASKET, mounting, turbocharger
10	J818823	4	STUD, turbocharger mounting, used with Ref. 11 nut only, if used
11	J818824	4	NUT, hex flange, special, 10 mm – 1.5, used with Ref. 10 stud only, if used
12	J918562	1	HOSE, 21-3/16 inch (538 mm) long, oil supply, turbocharger
13	J919687	2	CONNECTOR, ELEC, ADAPTER female hex, special, includes Ref. 14
14	238-5013	1	O-RING, -013, 70 Duro, .426″ ID x .070″ Thk
15	J917936	1	TUBE, oil drain
16	J914388	1	GASKET, turbo oil drain tube
17	845-8016	2	BOLT, Hex Flg, M8 x 16, 8.8, Full Thd
18	J903745	1	HOSE, LARGE, 3 inch (76 mm) long, turbocharger oil drain
19	214-1416	2	CLAMP, HOSE, #16, 0.81/1.50 Type F Worm, Adj.
20	J903744	1	FITTING, PIPE, TUBE turbocharger oil drain
21	J906742	1	TUBE, air, crossover
22	J916529	2	SLEEVE, TRANSMISSION, HOSE, 3 inch (76 mm) long, crossover tube
23	J924386	4	COLLAR CLAMP, adjustable, special
24	J906741	1	MANIFOLD, exhaust
25	J929012	1	GASKET, exhaust manifold, 0.54 mm thick, replaces J921787
26	J929537	12	BOLT, hex, special, exhaust manifold to cylinder head, replaces 814-100701
27	J914708	12	PLATE, LOCKING
28	J906737	1	COVER ASSY, intake manifold
29	J914311	1	GASKET, intake manifold cover
30	J918109	18	SCREW, Hex Flg Hd, M8 x 1.25 x 25, Special, Intake manifold cover to cylinder head
1	J919199	1	TURBOCHARGER, ASSEMBLY engine, new, Includes: Ref. 2 thru 28
2	J927907	1	COVER, VALVE, replaces J907734
3	J905449	1	SEAL, RUBBER, valve cover
4	J910824	6	O-RING, cover bolt
5	J916585	6	SCREW, BOLT hex flange cap, special
6	J902468	1	PLUG, CAP oil filler
7	J902466	1	SEAL, cap sealing
8	J928168	1	GASKET, cylinder head, standard, replaces J921850
8	J928180	1	GASKET, cylinder head, 0.25 mm thicker, replaces J921852
8	J928181	1	GASKET, cylinder head, 0.50 mm thicker, replaces J921853
9	J907861	1	EYE, LIFTING, lifting, front
10	J906440	1	EYE, LIFTING, lifting, rear
11	614-12025	2	BOLT, Hex, M12 x 25, 8.8
12	854-12025	2	BOLT, Hex Flg, M12 x 25, 10.9, Heavy
13	J920497	1	ELBOW, CONNECTOR 90 degree, breather vent
14	238-5115	1	O-RING, -115, 70 Duro, .674″ ID x .103″ Thk
15	J918167	1	TUBE, vent, air, BSN 44808257
16	222-42	1	ELBOW, 90є, 1/2″-24 Fem x 1/8″-27 NPTF, ELBOW 90 degree, compression, 1/4 tube O.D. x 1/8 inch
16	222-42	2	ELBOW, 90є, 1/2″-24 Fem x 1/8″-27 NPTF, ELBOW 90 degree, compression, 1/4 tube O.D. x 1/8 inch
17	J924589	1	TUBE, vent, air, engine serial number 44808257 and after, Includes: Ref. 18
18	222-153	2	SLEEVE, 1/4″ Tube
19	222-22	1	FITTING, 1/2″-24 x 1/8″ NPTF w/Nut, ADAPTER compression, 1/4 tube O.D. x 1/8 inch PT, tube to
1	J914310	1	GASKET, thermostat housing
2	J907242	2	THERMOSTAT, engine coolant
3	J913708	1	HOUSING, thermostat, no longer available, order J926509 housing below, BSN 44808257
4	845-8080	2	BOLT, Hex Flg, M8 x 80, 8.8
6	J912800	1	CONNECTION, TUBE water outlet
7	J918779	1	GASKET, outlet tube, water
8	845-8095	2	BOLT, Hex Flg, M8 x 95, 8.8, BOLT heavy hex flange, 8 – 1.25 x 95 mm
9	J918544	1	SUPPORT, mounting, alternator
10	845-8025	4	BOLT, Hex Flg, M8 x 25, 8.8
11	J912837	1	COCK, VALVE shutoff
12	A77544	1	FILTER, water conditioning, precharge
13	238-5111	1	O-RING, -111, 70 Duro, .424″ ID x .103″ Thk
14	A77623	1	ADAPTER, water filter
15	845-6010	1	BOLT, Hex Flg, M6 x 10, 8.8, Full Thd, BOLT heavy hex flange, 6 – 1.0 x 10 mm
16	J911925	1	COUPLING, hose
17	J911901	1	VALVE, CHECK
1	J922587	1	CYLINDER HEAD, ASSEMBLY new, without valves, no longer available, for service order J922052
2	J923564	12	GUIDE, VALVE, valve stem, replaces J901187
3	J924582	6	INSERT, INSERT intake, replaces J908830
3	J925468	6	SEAT, VALVE, INSERT seat, intake valve, 0.254 mm oversize, service repair only, replaces J914839
3	J925470	6	SEAT, VALVE, INSERT seat, intake valve, 0.508 mm oversize, service repair only, The oversize valve
4	J929005	6	INSERT, seat, exhaust valve, replaces J904716 and J924583
4	J929006	6	INSERT, INSERT seat, exhaust valve, 0.254 mm oversize, service repair only, replaces J914836 and
4	J929007	6	INSERT, INSERT seat, exhaust valve, 0.508 mm oversize, service repair only, replaces J925471, The
5	A77530	1	PLUG, expansion, 30 mm O.D., used with J916464 head assembly
6	A77782	2	PLUG, expansion, 58 mm O.D.
7	A77590	5	PLUG, expansion, used with J916464 head assembly
8	A77534	1	PLUG, hex, 1/16 inch PT
9	A77428	1	PLUG, hex socket, 1/4 inch PT
10	A77429	2	PLUG, hex socket, 1/2 inch PT
11	J924148	2	PLUG, hex magnetic, special, 22 mm – 1.5
12	J902425	2	WASHER, sealing, plug
13	J901177	24	KEY, KEEPER valve
14	J906412	12	SPRING, VALVE
15	J912976	12	RETAINER, valve spring
16	J915707	12	SEAL, intake and exhaust valve stem and guide
17	J924492	6	VALVE, ENGINE, INLET, STD
18	J921444	6	VALVE, ENG EXHAUST, STD, replaces J915506
19	J917728	14	BOLT, BOLT cylinder head, 160 mm long
19	J917729	12	SCREW, BOLT cylinder head, 80 mm long
20	J925031	12	TAPPET, valve, push rod, replaces J907240
21	J905194	12	ROD, PUSH, rocker arm
22	J905870	6	SUPPORT, shaft, rocker arm
23	J901693	6	CLAMP, retaining, shaft
24	868-10065	12	SCREW, 12 Pt Hd, M10 x 65, 12.9, BOLT 12 point flange, 10 – 1.5 x 65 mm, class 12.9
25	J919677	1	MANIFOLD, oil, rocker arm
26	J901717	12	ROCKER, ARM ASSEMBLY, includes ref. 27, 28, and 29
27	J937438	1	SET SCREW, Hex Skt, 3/8″-24 x 33mm, Adj, Ball Point, slotted set, adjusting, special
28	425-116	1	NUT, 3/8″-24, G5, Hex
30	J919435	6	SHAFT, rocker
31	J906100	12	CUP, SPRING, WASHER
32	J907206	12	WASHER, flat, special
33	100-1187	12	RING, SNAP, #87, Ext
1	J917882	1	CAMSHAFT, ASSEMBLY engine, no longer available, order Ref. 7, J924471
2	J917883	1	PIN, dowel, gear, if used
3	J927155	1	SUPPORT, thrust, camshaft, replaces J914641
4	J917328	1	GEAR, camshaft
5	J900227	2	SCREW, Hex, M8 x 1.25 x 22
6	J901685	7	BUSHING, camshaft
7	J924471	1	CAMSHAFT, engine
8	126-112	1	KEY, WOODRUFF, #6, 5/32″ x 5/8″, HT, If used
1	J926145	1	CRANKCASE, BLOCK ASSEMBLY stripped engine, replaces J919934 and J923289, Includes: Ref. 2
2	J917313	7	CAP, bearing, main
3	J916369	14	SCREW, Hex Flg Hd, M14 x 128, Main bearing cap to block
4	J901685	7	BUSHING, camshaft
5	A77782	1	PLUG, expansion, 58 mm O.D.
6	A77586	1	PLUG, expansion, 43 mm O.D.
7	A77506	4	PLUG, PLUG – expansion, 21 mm O.D.
8	J905401	4	PLUG, expansion, 35 mm O.D.
9	A77530	2	PLUG, expansion, 30 mm O.D.
10	J920706	1	PLUG, expansion, 22 mm O.D., not used in this application, replaces A77439
11	41-3044	1	PLUG, Exp, 2 3/4″, Replaces J901969
12	J901846	4	PIN, dowel
13	J906619	6	PLUG, hex, 1/8 inch PT
14	A77429	5	PLUG, hex socket, 1/2 inch PT
15	A77505	2	PLUG, hex socket, 3/4 inch PT
16	A77533	1	PLUG, hex socket, 1 inch PT
17	J919003	12	NOZZLE INJECTION, piston cooling
18	J900257	2	PIN, dowel, 16 mm long
19	217-103	1	COCK, DRAIN, VALVE 1/4 inch PT, coolant, replaces A77425
20	J903744	1	FITTING, PIPE, TUBE turbocharger oil drain, see Fig. 2-32 for connecting turbocharger parts
23	J905113	1	CABLE, engine block heater, 6 feet long
25	J910517	1	O-RING, heater sealing, engine block
1	A77424	1	PLUG, CAP oil fill tube
2	J914019	1	TUBE, oil fill, upper
3	A77661	1	HOSE, 2-1/2 inch (64 mm) long, oil fill
4	214-1428	2	CLAMP, HOSE, #28, 1.31/2.25 Type F Worm, Adjustable
5	J914163	1	TUBE, oil fill, lower
6	J914022	2	CLAMP, P-type, filler tube retaining
7	613-8020	2	BOLT, Hex, M8 x 20, 8.8, Full Thd, BOLT hex, full threads, 8 – 1.25 x 20 mm
8	J914020	1	BRACKET, support
9	614-8025	2	BOLT, Hex, M8 x 25, 8.8
10	892-11008	4	WASHER, LOCK, M8
11	829-1308	2	NUT, M8, Cl 10
12	896-11008	2	WASHER, M8 x 17.5 x 2, HT, flat, 9 x 17 x 2 mm, hardened
13	102439A1	2	SPACER, 13/32 x 1/2 x 3/8 inch, replaces D35217
14	118880A1	1	TUBE, dipstick
15	118790A1	1	DIPSTICK, oil gauge
16	118788A1	1	CLAMP, dipstick support
17	515-22127	1	CLAMP, 1/2″, Insul, 5/16″ Bolt, P-type
18	413-516	1	BOLT, Hex, 5/16″-18 x 1″, G5, Full Thd, hex, 5/16 NC x 1 inch
19	231-5145	1	NUT, Flg, USR, 5/16″-18
20	1541750C1	1	HOSE, FLEXIBLE, 148-1/16 inch (3760) mm long, cut from 364360C1 bulk hose, crankcase breather
21	281-14810	1	SCREW, SELF TAPPING, Hex Hd, 5/16″ x 5/8″, self-tapping, hex washer head, 5/16 NC x 5/8 inch
22	515-23317	1	CLAMP, 1 1/4″, Insul, 3/8″ Bolt, P-type, Tube retaining
23	515-23381	1	CLAMP, 1 1/2″, Insul, 3/8″ Bolt, P-type, closed
24	1301387C2	3	CLIP, CLAMP square, 2 inch ID, closed
25	515-25476	3	CLAMP, 1 7/8″, Insul, 1/2″ Bolt
26	1301342C1	1	FITTING, ADAPTER straight, special, oil drain
27	1954736C1	8	CLAMP, HOSE, No. 24, hose
28	1329977C2	1	HOSE, 33 inch (840 mm) long, cut from 1977295CX bulk hose, crankcase breather intermediate, see
29	1977169C1	1	TEE, oil drain
30	1977293C3	1	HOSE, 67 inch (1700 mm) long, cut from 1977295CX bulk hose, breather, lower, see this Figure
31	1977212C1	1	BRACKET, BRACKET oil drain shield
32	409-7616	2	BOLT, Hex Flg, 3/8″-16 x 1″, Serr
33	231-5146	2	NUT, Flg, USR, 3/8″-16
34	1330429C1	1	VALVE, DRAIN, oil
35	J900216	1	RING, PACKING, WASHER sealing, drain plug
36	1329978C3	1	HOSE, 18-1/8 inch (430 mm) long, crankcase oil drain
37	214-1416	1	CLAMP, HOSE, #16, 0.81/1.50 Type F Worm, Adj.
1	J917443	1	CRANKSHAFT, ASSEMBLY engine, new, Includes: Ref. 2 and 3
2	J918380	1	GEAR, crankshaft
3	J904483	1	PIN, dowel
5	J925568	1	DAMPER, PULLEY crankshaft vibration
6	J906733	4	BOLT, hex flange, special, 14 x 35 mm
8	J921042	1	COVER, REAR, RETAINER seal
9	J914301	1	GASKET, rear cover retainer
10	845-6015	8	BOLT, Hex Flg, M6 x 15, 8.8, Full Thd, BOLT heavy hex flange, 6 – 1.0 x 15 mm
11	A77711	6	BEARING LINER, main, upper and lower set, standard
11	A77712	6	BEARING LINER, main, upper and lower set, 0.25 mm undersize
11	A77713	6	BEARING LINER, main, upper and lower set, 0.50 mm undersize
11	A77714	6	BEARING LINER, main, upper and lower set, 0.75 mm undersize
11	A77715	6	BEARING LINER, main, upper and lower set, 1.0 mm undersize
12	A77843	1	BEARING LINER, main thrust, upper and lower set, standard, replaces A77706
12	A77844	1	BEARING LINER, main thrust, upper and lower set, 0.25 mm undersize, replaces A77707
12	A77845	1	BEARING LINER, main thrust, upper and lower set, 0.50 mm undersize, replaces A77708
12	A77846	1	BEARING LINER, main thrust, upper and lower set, 0.75 mm undersize, replaces A77709
12	A77847	1	BEARING LINER, main thrust, upper and lower set, 1.0 mm undersize, replaces A77710
12	A77848	1	BEARING, CRANKSHAFT, main thrust, upper and lower set, standard journal diameter, 0.25 mm
12	A77849	1	BEARING, CRANKSHAFT, main thrust, upper and lower set, standard journal diameter, 0.50 mm
12	A77850	1	BEARING, CRANKSHAFT, main thrust, upper and lower set, 0.50 mm undersize journal diameter
13	J918113	1	SHIELD, dust, front seal, order Ref. 14, A77790 Kit
14	A77790	1	KIT, SEALS, oil, crankshaft front, Includes: Ref. 15 thru 18
12	A77846	1	BEARING LINER, main thrust, upper and lower set, 0.75 mm undersize, replaces A77709
18	J918113	1	SHIELD, dust, front seal
19	A77808	1	KIT, SERVICE, wear sleeve, crankshaft front, Includes: Ref. 20 thru 23
23	J924987	1	SHIELD, dust
24	A77809	1	KIT, GASKET, oil seal, crankshaft rear, Includes: Ref. 25 and 26
28	A77810	1	KIT, SERVICE, KIT wear sleeve, crankshaft rear, Includes: Ref. 29 and 32
1	J917052	1	FLYWHEEL, ASSEMBLY engine, Includes: Ref. 2
2	J905427	1	GEAR, ring, flywheel
3	J901395	8	SCREW, Hex, M12 x 1.25 x 32, Spc
4	J900269	8	WASHER, flat, special, flywheel bolt
7	J913593	1	PLATE, backing, flywheel housing
8	854-12040	10	BOLT, Hex Flg, M12 x 40, 10.9
9	J912473	1	SEALRING, flywheel housing to block
10	J908181	8	SCREW, BOLT hex, special, 12 – 1.25 x 50 mm
1	J919937	1	SLEEVE CYLINDER, piston
2	J907177	1	O-RING, sleeve
4	100-21175	2	RING, SNAP, 1.75″, Int, #175, (Replaces J901996 and G109044)
5	A77802	1	RING SET, PISTON, KIT replaces A77744, Includes: Ref. 6, 7, and 8
9	J901597	6	PIN, piston
11	J913990	1	BUSHING, connecting rod
12	J924351	2	SCREW, BOLT special, rod, bearing cap, replaces J901380 and J920799, connecting rod
13	J901381	2	NUT, hex, rod bolt, connecting rod
14	A77563	6	BEARING LINER, KIT upper and lower, standard, connecting rod
14	A77564	6	BEARING LINER, KIT upper and lower, 0.25 mm undersize, connecting rod
14	A77565	6	BEARING LINER, KIT upper and lower, 0.50 mm undersize, connecting rod
14	A77566	6	BEARING LINER, KIT upper and lower, 0.75 mm undersize, connecting rod
14	A77567	6	BEARING LINER, KIT upper and lower, 1.00 mm undersize, connecting rod
1	J918334	1	HEAD, FILTER, filter, oil
2	J906619	2	PLUG, hex, 1/8 inch PT
3	A77722	1	PIN, dowel, locating
4	A77505	1	PLUG, hex socket, 3/4 inch PT, filter head
5	J902338	1	VALVE, PRESSURE RELIEF
6	J918532	1	PLUNGER, regulator
7	A77541	1	SPRING, compression
8	J919016	1	PLUG, hex, special, 24 mm – 1.50, regulator, Includes: Ref. 9
9	238-5022	1	O-RING, -022, 70 Duro, .989″ ID x .070″ Thk
10	845-8065	11	BOLT, Hex Flg, M8 x 65, 8.8, BOLT heavy hex flange, 8 – 1.25 x 65 mm, oil filter head to cylinder block
11	J919562	1	FILTER, ENGINE OIL, OIL, cartridge, engine
12	J921605	1	GASKET, filter head
13	J918175	1	CORE-OIL COOLER
14	J918174	1	GASKET, cooler core
15	J919015	1	THERMOSTAT, temperature
16	A77724	1	O-RING, sealing
17	J922882	1	COVER, oil cooler, replaces J918403
18	J918332	1	GASKET, cooler cover, oil cooler
19	J907860	4	BOLT, Hex, Flg Hd, M8 x 25, Spcl
20	217-439	1	PLUG, Hex Soc, 1/2″-14, hex socket headless, 1/2 inch PT, water drain
1	J924644	1	PUMP, ENGINE OIL, new, no longer available, order J926201 assembly, 24 teeth drive gear, replaces
1	J926201	1	PUMP, ENGINE OIL, ASSEMBLY oil, 24 teeth drive gear, replaces J921067 and J924644
2	614-8030	4	BOLT, Hex, M8 x 30, 8.8, Full Thd
3	J921719	1	TUBE, with screen, oil suction
4	J908738	2	SPACER, mounting
5	845-6030	2	BOLT, Hex Flg, M6 x 30, 8.8, BOLT heavy hex flange, 6 – 1.0 x 30 mm
6	J914302	1	GASKET, mounting, oil suction tube, Part of KIT, part number A77679
7	845-6015	2	BOLT, Hex Flg, M6 x 15, 8.8, Full Thd, BOLT heavy hex flange, 6 – 1.0 x 15 mm
8	J906216	1	NUT, hex flange, special, 6 mm – 1.0
9	J910960	1	WASHER, flat, special
10	J913427	1	BRACE, suction tube
11	J914015	1	PAN, ENGINE OIL, oil, engine
12	J920400	32	BOLT, Hex, Flg Hd, M8 x 21, Spcl, hex flange cap, special, oil pan to block, replaces J907860
13	J910266	32	WASHER, spring, Belleville
14	J908316	32	WASHER, flat, special, 9 x 16 x 1 mm
15	J924148	1	PLUG, hex magnetic, special, 22 mm – 1.5, heater hole, replaces J904386
16	J902425	1	WASHER, sealing, plug, Part of KIT, part number A77679
17	J924147	1	PLUG, hex magnetic, special, 18 mm – 1.5, drain, replaces J911638
18	J920773	1	WASHER, SEALING, WASHER sealing, drain plug, Part of KIT, part number A77679
22	J905113	1	CABLE, engine block heater, 6 feet long, oil pan heater kit
23	J902425	1	WASHER, sealing, plug, oil pan heater kit, When engine oil heater kit is ordered, Ref. 23, J902425
1	J914310	1	GASKET, thermostat housing
2	J918779	1	GASKET, outlet tube, water
3	J915707	12	SEAL, intake and exhaust valve stem and guide
4	J911941	1	GASKET, mounting, turbocharger
5	J929012	1	GASKET, exhaust manifold, 0.54 mm thick (set of 6) replaces J921787
6	J914311	1	GASKET, intake manifold cover
7	J914388	1	GASKET, turbo oil drain tube, turbocharger
8	J902466	1	SEAL, cap sealing, oil fill cap to valve cover
9	J905449	1	SEAL, RUBBER, valve cover
10	J910824	6	O-RING, cover bolt
11	J909886	6	SEAL, SLEEVE injector
12	J903380	7	SEAL, connector, fuel injection nozzle
13	238-5115	1	O-RING, -115, 70 Duro, .674″ ID x .103″ Thk, Connector to valve cover
14	J906659	6	SEAL, injector nozzle
15	238-5111	1	O-RING, -111, 70 Duro, .424″ ID x .103″ Thk, Water filter shutoff valve
16	J918610	1	HOSE, LARGE, 2 inch (51 mm) long, breather tube to connector
17	J919677	1	MANIFOLD, oil, rocker arm
18	J914708	12	PLATE, LOCKING, bolt, exhaust manifold
19	J823921	1	GAUGE, cylinder head, bolt length
20	J903475	1	SEAL, front access cover, cylinder block
21	J917779	1	GASKET, front gear cover, high mount engine, used in A77726 kit, cylinder block
21	J917780	1	SEAL, GASKET front gear cover, low mount engine, not used in this application, use J917779, cylinder
22	J281721	1	GASKET, housing, gear, used in A77726 kit only, cylinder block
23	J915772	1	SEALRING, quad, timing pin housing
24	J919601	1	GASKET, access cover plate, cylinder block
25	J902089	1	SEAL, sealing, water pump, cylinder block
26	J914301	1	GASKET, rear cover retainer, crankshaft, cylinder block
27	J918174	1	GASKET, cooler core, cylinder block
28	J918332	1	GASKET, cooler cover, cylinder block
29	J901798	1	WASHER, SEALING, sealing, not used in this application, cylinder block
30	J923054	1	GASKET, mounting, fuel transfer pump, cylinder block
31	J912473	1	SEALRING, flywheel housing to block, cylinder block
32	238-5212	1	O-RING, -212, 70 Duro, .859″ ID x .139″ Thk, Backing plate plug, cylinder block
33	J907177	6	O-RING, sealing, sleeve, cylinder block
34	J913994	1	O-RING, sealing, cylinder block
1	1315653C3	1	RAIL ASSY., SUPPORT engine, left hand
2	409-7612	6	BOLT, Hex Flg, 3/8″-16 x 3/4″, Serr
3	231-5146	4	NUT, Flg, USR, 3/8″-16
4	409-7820	4	BOLT, Hex Flg, 1/2″-13 x 1 1/4″, Serr
5	231-5148	4	NUT, Flg, USR, 1/2″-13
6	194915C2	4	ISOLATOR, INSULATOR engine snubber, front and rear
7	413-1056	4	BOLT, Hex, 5/8″-11 x 3 1/2″, G5
8	107813R1	4	WASHER, flat, 21/32 x 2-1/2 x 11/64 inch
9	232-41110	4	NUT, LOCK, 5/8″-11, GC
10	1315654C3	1	RAIL ASSY., SUPPORT engine, right hand, replaces 1315654C2
11	409-7616	6	BOLT, Hex Flg, 3/8″-16 x 1″, Serr
12	231-5146	6	NUT, Flg, USR, 3/8″-16
13	409-7820	4	BOLT, Hex Flg, 1/2″-13 x 1 1/4″, Serr
14	231-5148	4	NUT, Flg, USR, 1/2″-13
15	1315644C1	1	SUPPORT, engine, left hand front
16	1315645C1	1	SUPPORT, engine, right hand front
17	854-12025	8	BOLT, Hex Flg, M12 x 25, 10.9, Heavy
18	1330098C2	1	SUPPORT, engine, right hand rear, replaces 1329775C1
19	1330099C2	1	SUPPORT, engine, right hand front, replaces 1329776C1
21	231-5146	10	NUT, Flg, USR, 3/8″-16
20	477-73816	10	SCREW, Sltd Serr Truss Hd, 3/8″ x 1″, Special
1	J923480	1	PUMP, FUEL INJECTION, ASSEMBLY fuel, new, parts list Fig. 3-6
3	J909886	6	SEAL, SLEEVE injector
4	J910279	6	CLAMP, fuel injector
5	845-8080	6	BOLT, Hex Flg, M8 x 80, 8.8
6	J906783	1	TUBE, fuel injector, No. 1 cylinder
7	J906784	1	TUBE, fuel injector, No. 2 cylinder
8	J906785	1	TUBE, fuel injector, No. 3 cylinder
9	J917776	2	BRACE, BRACKET fuel tube
10	J917747	4	CLAMP, fuel tube
11	J904519	2	SUPPORT, tube retaining
12	J920854	4	SCREW, Hex Hd, M5 x .8 x 20, w/LW, Replaces J917712 and J903723
14	J910521	1	TUBE, fuel injector, No. 4 cylinder
15	J906787	1	TUBE, fuel injector, No. 5 cylinder
16	J906788	1	TUBE, fuel injector, No. 6 cylinder
17	J920595	1	TUBE ASSY., fuel drain
18	J903380	6	SEAL, connector
19	J905307	6	BOLT, BANJO, M6 x 1 x 14.3, BOLT banjo drain, special
20	J924726	1	BOLT, BANJO, check, replaces J916360
21	J918188	2	WASHER, sealing
1	J925955	1	ADAPTER, fuel filter, replaces J903845
2	J903640	1	FILTER, FUEL
3	J912923	1	TUBE, fuel supply
4	J914711	1	CLIP, CLAMP P-type
5	J918191	2	RING, PACKING, WASHER sealing, special, 12 x 18 x 1 mm
8	J918192	2	RING, PACKING, WASHER sealing, special, 14 x 20 x 1 mm
9	J907541	1	JACK SCREW, BOLT banjo connector
10	J917998	1	PUMP, fuel lift and transfer, see J926764 repair kit below
11	J923054	1	GASKET, mounting, fuel transfer pump, replaces J914304
12	845-8020	2	BOLT, Hex Flg, M8 x 20, 8.8, Full Thd
13	J906790	1	TUBE, supply
14	J918191	2	RING, PACKING, WASHER sealing, special, 12 x 18 x 1 mm
15	J916361	1	BOLT, BANJO, banjo connector, 12 – 1.5 x 24 mm
16	J911447	1	CONNECTOR, banjo, fuel return
17	J912886	1	VALVE, overflow
29	J923054	2	GASKET, mounting, fuel transfer pump, replaces J914304
1	J923480	1	PUMP, FUEL INJECTION, ASSEMBLY fuel, new, Includes: Ref. 2 thru 19
2	A77720	1	PIN, timing
3	3051337R1	1	WASHER, SEALING, M18 x 24 x 1.5, WASHER sealing, replaces 933222R1
4	J912888	1	PLUG, timing
5	A41856	1	O-RING, sealing
6	J912886	1	VALVE, overflow
7	933697R1	1	WASHER, SEALING, M10 x 13.5 x 1, WASHER valve sealing
8	J910979	1	LEVER, pump shutoff
9	J912890	1	SPRING, lever shutoff
10	691292C1	1	RETAINER, HOUSING spring return
11	A71110	1	GASKET, mounting, replaces A46322
12	680187C1	1	O-RING, sealing, special, shutoff shaft
13	1808728C1	1	LEVER, throttle control
14	1808822C1	1	THUMB SCREW, M6 x 26, BOLT throttle lever
15	829-1306	1	NUT, M6, Cl 10, Replaces 1806312C1
16	895-11006	1	WASHER, M6
17	892-11006	1	WASHER, LOCK, M6
18	A77775	1	WASHER, lock
19	A41852	1	NUT, hex, self-locking
22	J912614	1	GEAR, fuel pump
23	J916284	1	O-RING, sealing, fuel injection pump
24	J915036	4	STUD, pump mounting
25	J902662	4	NUT, hex flange, 10 mm, fuel pump to timing gear housing
26	222-762	1	ELBOW, 90є, 7/16″-20, 45є Fl x 1/8″ NPT, 90 degree, 7/16-20 45 degree flare x 1/8 inch PT
27	J915172	1	FITTING, ELBOW 90 degree, 7/16-20 straight thread x 1/8 inch PT, pump lubrication
28	J906747	1	HOSE ASSY., 20 inch (508 mm) long, lubrication
1	J909886	1	SEAL, SLEEVE injector
2	J903380	1	SEAL, connector
3	J908507	1	INJECTOR ASSY., fuel, Includes: Ref. 5 thru 10, Whenever a nozzle is removed from cylinder head
5	1806233C1	5	SHIM, nozzle, 1.00 mm
5	1806234C1	5	SHIM, nozzle, 1.04 mm
5	1806235C1	5	SHIM, nozzle, 1.08 mm
5	1806236C1	5	SHIM, nozzle, 1.10 mm
5	1806237C1	5	SHIM, nozzle, 1.14 mm
5	1806238C1	5	SHIM, nozzle, 1.18 mm
5	1806239C1	5	SHIM, nozzle, 1.20 mm
5	1806240C1	5	SHIM, nozzle, 1.24 mm
5	1806241C1	5	SHIM, nozzle, 1.28 mm
5	1806242C1	5	SHIM, nozzle, 1.30 mm
5	1806243C1	5	SHIM, nozzle, 1.34 mm
5	1806244C1	5	SHIM, nozzle, 1.38 mm
5	1806245C1	5	SHIM, nozzle, 1.40 mm
5	1806246C1	5	SHIM, nozzle, 1.44 mm
5	1806247C1	5	SHIM, nozzle, 1.48 mm
5	1806248C1	5	SHIM, nozzle, 1.50 mm
5	1806249C1	5	SHIM, nozzle, 1.54 mm
5	1806250C1	5	SHIM, nozzle, 1.58 mm
5	1806251C1	5	SHIM, nozzle, 1.60 mm
5	1806252C1	5	SHIM, nozzle, 1.64 mm
5	1806253C1	5	SHIM, nozzle, 1.68 mm
5	1806254C1	5	SHIM, nozzle, 1.70 mm
5	1806255C1	5	SHIM, nozzle, 1.74 mm
5	1806256C1	5	SHIM, nozzle, 1.78 mm
5	1806257C1	5	SHIM, nozzle, 1.80 mm
5	1806258C1	5	SHIM, nozzle, 1.84 mm
5	1806259C1	5	SHIM, nozzle, 1.88 mm
5	1806260C1	5	SHIM, nozzle, 1.90 mm
5	1806261C1	5	SHIM, nozzle, 1.94 mm
5	1806262C1	5	SHIM, nozzle, 1.98 mm
6	J905153	1	SPINDLE, SEAT nozzle pressure spring
7	J905152	1	SPRING, nozzle pressure
8	J905154	1	PLATE, STOP nozzle valve
11	J906659	6	SEAL, injector nozzle, 7 mm injector tip, Whenever a nozzle is removed from cylinder head, J906659
1	144535R1	1	ELBOW, 90 degree, special, 3/8 inch inverted flare, lower fuel return tube
5	612277C2	1	HEAD, FILTER, fuel filter
6	A184776	1	FILTER, FUEL
7	221-841	2	PLUG, hex socket, 1/4 inch PT
8	444614	1	PLUG, Hex Hd, 1/8″-27, Brass, hex, 1/8 inch PT
9	424-564	2	BOLT, Hex, 5/16″-18 x 4″, G2, BOLT hex, 5/16 NC x 4 inch, grade 2
10	231-5145	4	NUT, Flg, USR, 5/16″-18
11	222-1026	2	ELBOW, 90є, 5/8″-18 Inv Fl x 1/4″ NPT
12	1315506C1	1	TUBE, fuel supply, lower
13	222-1055	2	CONNECTOR, HYD., 3/8″ Inv Fl, COUPLING, 5/8-18 inch inverted flare
14	1330563C1	1	TUBE, fuel supply, upper
15	183825C1	3	CLAMP, fuel tube
17	495-81121	1	WASHER, .344″ x 1 1/2″ x .060″, flat, 11/32 x 1-1/2 x 1/16 inch
18	231-5144	4	NUT, Flg, USR, 1/4″-20
19	1330562C2	1	TUBE, fuel return, upper
20	1330564C1	1	PLATE, SUPPORT fuel tube
21	183821C1	1	CLAMP, tube, single, 3/8 inch O.D.
23	196517C1	1	SUPPORT, fuel tubes
24	161945C1	2	SCREW, Sltd Serr Truss Hd, 5/16″-18 x 1″, slotted truss head, 5/16 NC x 1 inch
25	183653C2	1	TUBE ASSY., fuel return, lower
28	1251794C1	1	HOSE, TUBE, 125 inch (3175 mm) long, cut from 74813C1 bulk tube, fuel vent, see this Figure
29	214-1704	1	CLAMP, HOSE, #4, 0.25/0.62 Type M Worm, Adjustable
30	533959R1	1	STRAP, CABLE, .135″ x 11″, tie, 10 inch, retaining
31	195803C1	1	GROMMET, 3/8 inch
32	362120R1	3	CLAMP, CLAMP P-type, retaining
36	1979437C1	1	HOSE, LARGE, 13 inch (331 mm) long, cut from 364357C1 bulk hose, fuel return, see this Figure
37	214-1704	2	CLAMP, HOSE, #4, 0.25/0.62 Type M Worm, Adjustable
40	218-444	1	CONNECTOR, HYD., 3/4″-16, 37є x 3/8″-18, NPTF, straight, 3/4-16 flare x 3/8 inch PT
41	1994884C1	1	TUBE, fuel, filter base to tank
42	218-493	1	ELBOW, 90є, 3/4″-16, 37є x 1/2″-14, NPTF, ELBOW 90 degree, 3/4-16 flare x 1/2 inch PT
43	1345205C1	1	VALVE, SHUT-OFF, fuel shut off
44	221-88	1	REDUCER, Hex, 1/2″ x 1/4″ NPT, REDUCER pipe, 1/2 male x 1/4 inch female
45	217-195	1	FITTING, 1/4″-18 NPTF, Brass, NIPPLE straight, 1/4 PT x 1-3/8 inch
16	413-420	4	BOLT, Hex, 1/4″-20 x 1 1/4″, G5
1	144535R1	1	ELBOW, 90 degree, special, 3/8 inch inverted flare, lower fuel return tube
5	612277C2	1	HEAD, FILTER, fuel filter
6	A184776	1	FILTER, FUEL
7	221-841	2	PLUG, hex socket, 1/4 inch PT
8	444614	1	PLUG, Hex Hd, 1/8″-27, Brass, hex, 1/8 inch PT
9	424-564	2	BOLT, Hex, 5/16″-18 x 4″, G2, BOLT hex, 5/16 NC x 4 inch, grade 2
10	231-5145	4	NUT, Flg, USR, 5/16″-18
11	222-1026	2	ELBOW, 90є, 5/8″-18 Inv Fl x 1/4″ NPT
12	1977001C1	1	TUBE
13	222-1055	2	CONNECTOR, HYD., 3/8″ Inv Fl, COUPLING, 5/8-18 inch inverted flare
14	1330563C1	1	TUBE, fuel supply, upper
15	183825C1	3	CLAMP, fuel tube
17	495-81121	1	WASHER, .344″ x 1 1/2″ x .060″, flat, 11/32 x 1-1/2 x 1/16 inch
18	231-5144	4	NUT, Flg, USR, 1/4″-20
19	1330562C2	1	TUBE, fuel return, upper
20	1330564C1	1	PLATE, SUPPORT fuel tube
21	183821C1	1	CLAMP, tube, single, 3/8 inch, O.D.
23	196517C1	1	SUPPORT, fuel tubes
24	161945C1	2	SCREW, Sltd Serr Truss Hd, 5/16″-18 x 1″, slotted truss head, 5/16 NC x 1 inch
25	183653C2	1	TUBE ASSY., fuel return, lower
28	1251794C1	1	HOSE, TUBE 125 inch (3175 mm) long, cut from 74813C1 bulk tube, fuel vent, see this Figure
29	214-1704	1	CLAMP, HOSE, #4, 0.25/0.62 Type M Worm, Adjustable
30	533959R1	1	STRAP, CABLE, .135″ x 11″, tie, 10 inch, retaining
31	195803C1	1	GROMMET, 3/8 inch
32	362120R1	3	CLAMP, CLAMP P-type, retaining
36	1979437C1	1	HOSE, LARGE, 13 inch (331 mm) long, cut from 364357C1 bulk hose, fuel return, see this Figure
37	214-1704	2	CLAMP, HOSE, #4, 0.25/0.62 Type M Worm, Adjustable
40	218-444	1	CONNECTOR, HYD., 3/4″-16, 37є x 3/8″-18, NPTF, straight, 3/4-16 flare x 3/8 inch PT
41	1994884C1	1	TUBE, fuel, filter base to tank
42	218-493	1	ELBOW, 90є, 3/4″-16, 37є x 1/2″-14, NPTF, ELBOW, 90 degree, 3/4-16 flare x 1/2 inch PT
43	1345205C1	1	VALVE, SHUT-OFF, fuel shut off
44	221-88	1	REDUCER, Hex, 1/2″ x 1/4″ NPT, REDUCER pipe, 1/2 male x 1/4 inch female
45	217-195	1	FITTING, 1/4″-18 NPTF, Brass, NIPPLE straight, 1/4 PT x 1-3/8 inch, brass, if used
46	1977001C1	1	TUBE, fuel supply, lower
47	144535R1	1	ELBOW, 90 degree, special, 3/8 inch inverted flare
48	196503C1	1	PUMP, fuel, electric
49	151446C1	2	SCREW, Sltd Serr Truss Hd, 5/16″-18 x 1 1/4″, slotted truss head, 5/16 NC x 1-1/4 inch
50	25553R1	8	WASHER, 13/32″ x 1 1/8″ x .134″, HDN, flat, 13/32 x 1-1/8 x 9/64 inch, hardened
51	231-5145	2	NUT, Flg, USR, 5/16″-18
52	217-42	1	REDUCER, 3/8″-18 NPTF x 1/4″-18 Fem NPTF
53	222-1016	1	CONNECTOR, HYD., 5/8″-18 Inv Fl x 1/4″ NPT, ADAPTER straight, 5/8-18 inverted flare x 1/4 inch PT
54	1977000C1	1	TUBE, filter to pump
16	413-420	4	BOLT, Hex, 1/4″-20 x 1 1/4″, G5
1	1259760C1	1	KNOB,BALL, throttle lever
2	1301183C96	1	LEVER ASSY., throttle control
3	154397C1	1	SPACER, 5/8″ Tube x 1 1/4″, tubular, 5/8 O.D. x 1-1/4 inch long
4	413-636	1	BOLT, Hex, 3/8″-16 x 2 1/4″, G5
5	425-106	1	NUT, 3/8″-16, G5
6	492-11038	1	WASHER, LOCK, 3/8″
7	941133C1	1	WASHER, throttle lever
9	495-71041	1	WASHER, 3/8″, flat, 13/32 x 1-1/4 x 3/32 inch
10	1977092C4	1	SUPPORT, throttle control
11	937059R1	2	SCREW, Sltd Serr Truss Hd, 1/4″-20 x 1/2″, slotted truss head, 1/4 NC x 1/2 inch
12	231-5144	2	NUT, Flg, USR, 1/4″-20
13	1338891C4	1	ANGLE, throttle stop
14	12-632	2	BOLT, CARRIAGE, Short NK, 3/8″-16 x 2″, G2
15	477-73812	2	SCREW, Sltd Serr Truss Hd, 3/8″ x 3/4″, slotted truss head, special, 3/8 NC x 3/4 inch
16	231-5146	4	NUT, Flg, USR, 3/8″-16
17	K11064	2	SPACER, 3/8″ Pipe x 1 1/4″, 3/8 ID x 1-1/4 inch
18	1301242C1	1	BRACKET, throttle support
20	1329389C1	1	CABLE, throttle
21	225-14210	2	NUT, #10-32
22	198823C1	2	GROMMET, rubber, 3/8 inch ID, throttle cable at grain tank
23	213-113	1	CLEVIS, ADJUSTABLE, #10-32, adjustable, No. 10 NF
24	1977009C4	1	BALL JOINT, No. 10, type AL, replaces 1977009C3
25	427-3071	1	PIN, CLEVIS, 3/16″ x .719″, clevis, 3/16 x 23/32 inch, hardened
26	432-416	1	PIN, SPLIT (COTTER), 1/16″ x 1″, 1/16″ x 1″, Replaces 432-412
27	1977034C2	1	SUPPORT, throttle cable, rear
28	854-10020	2	BOLT, Hex Flg, M10 x 20, 10.9
29	1977046C4	1	LEVER, pump throttle
30	615-6016	2	BOLT, Hex, M6 x 16, 8.8, Full Thd, BOLT hex, full threads, 6 – 1.0 x 16 mm
31	892-11006	2	WASHER, LOCK, M6
32	495-81006	2	WASHER, .266″ x 3/4″ x .060″, flat, 17/64 x 3/4 x 1/16 inch
1	193550C95	1	TANK, FUEL, ASSEMBLY 92-1/2 gallons, without plug, replaced by 197681A2
1	197681A2	1	TANK, FUEL, ASSEMBLY fuel, with 217-87 plug, replaces 197681A1 and 193550C95
2	104781C1	1	CAP, fuel tank, non vented
3	1308798C1	2	STRIP, lining, 72 inch (1829 mm) long, cut for 990541R1 bulk strip, fuel tank support, see this Figure
4	192381C3	2	SUPPORT, lower support, fuel tank bottom
5	1302029C1	2	SUPPORT, front support, fuel tank forward
6	198024C1	1	GAUGE, FUEL, SENSOR fuel level, fuel tank sending unit
7	168515C1	1	GASKET, fuel tank sending unit
8	1310675C1	5	SCREW, LOCK, Sltd Truss Hd, #10-24 x 3/4″, w/nylon LW, Sending Unit Mounting
9	1302031C1	2	STRAP, SUPPORT fuel tank retainer
10	1302030C1	2	BRACKET, front, fuel tank
11	535789R1	2	BOLT, Hex Flg, 5/16″-18 x 1 1/4″, Serr, BOLT hex flange, 5/16 NC x 1-1/4 inch
12	495-81112	4	WASHER, .344″ x 3/4″ x .120″, flat, 11/32 x 3/4 x 7/64 inch
13	492-11031	4	WASHER, LOCK, 5/16″
14	425-105	4	NUT, 5/16″-18, G5
15	413-516	2	BOLT, Hex, 5/16″-18 x 1″, G5, Full Thd, hex, 5/16 NC x 1 inch
16	135270	23	BOLT, Slotted Tr Hd, 5/16″-18 x 3/4″, slotted truss head, 5/16 NC x 3/4 inch
17	231-5145	23	NUT, Flg, USR, 5/16″-18
1	100827A1	1	HARNESS, engine
2	363660R1	1	CLIP, CLAMP engine block, rear
3	515-30222	2	CLAMP, 7/8″, 1/2″ Bolt, P-type, Engine harness
5	362123R1	3	CLIP, harness
6	370383R1	1	CLIP, CLAMP harness, long
8	221-93	1	REDUCER, Hex, 3/4″ x 1/2″ NPT, REDUCER pipe, 3/4 male x 1/2 inch female
9	399470R1	2	BOOT, cable
10	1341330C2	1	TRANSMITTER, SENDER oil pressure
11	92038C1	1	SENSOR, SWITCH high pressure, air conditioning
12	1345488C2	1	SWITCH, PRESSURE, coolant, high temperature
13	121756C2	1	SENSOR, coolant temperature
15	91448C2	1	ALTERNATOR, ASSEMBLY engine, 110 ampere, parts list Fig. 4-48
16	A187728	1	MOTOR, STARTER, ASSEMBLY engine, parts list Fig. 4-50
17	1964960C1	1	SWITCH, PRESSURE, pressure header lift
18	363444R1	1	CLAMP, J, 9/16″ Insul, 3/8″ Bolt, retaining, engine harness, front cover
19	183038A1	1	SWITCH, SOLENOID, SWITCH with barrier
20	425-105	2	NUT, 5/16″-18, G5
21	492-11031	2	WASHER, LOCK, 5/16″
22	225-14210	3	NUT, #10-32
23	492-11010	3	WASHER, LOCK, #10
24	178148A1	1	COVER, solenoid switch
25	L18337	4	STRAP, CABLE, 9.95″-12.1″ lg, tie, nylon retaining
34	702093C1	4	STRAP, CABLE, tie, nylon retaining
35	276-1458	2	SCREW, SELF TAPPING, Hex Hd, #10 x 1/2″, self-tapping, hex head, No. 10 NC x 1/2 inch
39	A145513	1	SENSOR, level, coolant
1	91822C3	1	HARNESS, steering column, with dimmer switch connector
2	D71346	4	LAMP, TAIL, lamp, No. 168
5	131066C91	1	SWITCH, turn signal
6	131107C1	1	SWITCH, neutral start
7	425-158	2	NUT, Jam, 1/2″-20, G5
8	1327674C1	1	BRACKET, ANGLE mounting, switch
9	135270	4	BOLT, Slotted Tr Hd, 5/16″-18 x 3/4″, slotted truss head, 5/16 NC x 3/4 inch
10	231-5145	6	NUT, Flg, USR, 5/16″-18
11	363444R1	6	CLAMP, J, 9/16″ Insul, 3/8″ Bolt, retaining, harness, steering column
12	245635C1	1	SWITCH, unloader tube control
13	340-10812	3	SCREW, Cross Pan Hd, #8-32 x 3/4″, machine, pan Phillips, No. 8 NC x 3/4 inch
15	1964933C1	1	HARNESS, horn
16	453453C1	1	SWITCH, push button, horn
17	166166R1	1	HORN, 12 volt, low note, alert
1	1994820C1	1	HARNESS, console , BSN JJC0105560
2	281-6456	10	SCREW, SELF TAPPING, Hex Wash Hd, #10 x 3/8″, self tapping, hex washer head, No. 10 NF x 3/4
2	261-13512	2	SCREW, SELF TAPPING, Cross Pan Hd, #10 x 3/4″, self tapping, pan Phillips, No. 10 NC x 3/4 inch
3	1252476C1	1	SWITCH, ignition, key starting
5	245219C1	1	SWITCH, rotor speed , BSN JJC0105560
6	375431R1	1	WASHER, flat, special, 19/32 x 1 x 1/8 inch
7	365502R1	1	NUT, flat hex, special
10	245854C1	1	BUZZER, ALARM audible
11	1301175C1	1	SWITCH, reel lift control
12	342-10610	2	SCREW, Cross Oval Hd, #6-32 x 5/8″, machine, oval Phillips, No. 6 NC x 5/8 inch
13	453453C1	1	SWITCH, push button, feeder reverser
14	1983394C2	7	RELAY, electrical, 12 volt, replaces 146461C1
17	299277C91	2	CLIP, CLAMP console harness
19	281-6456	2	SCREW, SELF TAPPING, Hex Wash Hd, #10 x 3/8″, self tapping, hex washer head, No. 10 NF x 3/4
20	1994871C1	1	GOVERNOR, RECTIFIER central load dump
23	1964919C1	1	SWITCH, IGNITION, feeder clutch , BSN JJC0105560
24	245632C1	1	SWITCH, separator clutch
25	245435C1	1	FUSE HOLDER, BLOCK for terminal, see Fig. 4-40 for correct assembly
29	107655C1	1	SWITCH, SOLENOID, SWITCH magnetic, cab power, Includes: Ref. 30 thru 33
30	225-14210	1	NUT, #10-32
31	492-11010	1	WASHER, LOCK, #10
32	425-105	2	NUT, 5/16″-18, G5
33	492-11031	2	WASHER, LOCK, 5/16″
34	399470R1	2	BOOT, cable
35	1994819C1	1	RELAY, time delay
37	453453C1	1	SWITCH, push button, ether start
38	245012C1	1	SWITCH, rocker, 4 wheel drive
39	245012C1	1	SWITCH, rocker, two speed, variable propulsion
40	245219C1	1	SWITCH, fan speed , BSN JJC0105560
41	260-1448	2	SCREW, SELF TAPPING, Cross Pan Hd, #8 x 1/2″, self tapping, pan Phillips, No. 8-18 x 1/2 inch
42	245334C1	1	PLUG, panel switch cover
43	245653C2	1	SWITCH, reel speed manual
44	1301036C1	1	BUTTON, KNOB control, reel speed switch
45	245509C1	1	SWITCH, reel, fore and aft
46	245871C1	1	BRACKET, circuit breaker
47	245765C1	2	CIRCUIT BREAKER, 30 ampere, work lamp and blower
48	276-1458	2	SCREW, SELF TAPPING, Hex Hd, #10 x 1/2″, self-tapping, hex head, No. 10 NC x 1/2 inch
49	245763C1	2	CIRCUIT BREAKER, 20 ampere, cab
50	245860C1	2	BAR, circuit breaker
51	107200C2	1	SWITCH, lamp, head
52	492-11010	8	WASHER, LOCK, #10
53	363660R1	1	CLIP, CLAMP twisted, console harness
54	135270	1	BOLT, Slotted Tr Hd, 5/16″-18 x 3/4″, slotted truss head, 5/16 NC x 3/4 inch
55	225-14210	8	NUT, #10-32
56	92065C1	1	GROMMET, rubber, console harness
59	121770C2	1	TRANSMITTER, MODULE low coolant
63	1345209C1	1	HARNESS, seat switch
64	195804C1	1	GROMMET, 1/2 inch
65	1983395C1	1	SWITCH, IGNITION, seat
66	440-1258	2	SCREW, Cross Pan Hd, 1/4″-20 x 1/2″, machine, pan Phillips, 1/4 NC x 1/2 inch
67	231-5145	1	NUT, Flg, USR, 5/16″-18
79	1983568C1	1	BUZZER, ALARM grain tank level
1	1994820C1	1	HARNESS, console , BSN JJC0105560
2	113699A1	2	RECTIFIER, locking, 2-5/8 inch long, console harness
3	245576C1	1	LIGHTER, CIGARETTE, cigar, 12 volt, Includes: Ref. 4
4	378781R1	1	LIGHTER, CIGARETTE, ELEMENT pop up, not shown
5	1983341C1	1	SWITCH, parking brake warning lamp
6	68107H	1	NUT, hex, special, lamp switch
7	166817C2	1	WASHER, flat, 9.0 x 51.0 x 1.6 mm, lamp switch
8	495-51053	1	WASHER, 1/2″, flat, 17/32 x 1 x 1/16 inch
8	495-51041	1	WASHER, 3/8″, flat, 13/32 x 47/64 x 1/16 inch
9	362120R1	1	CLAMP, CLAMP P-type, console harness, front
10	198823C1	1	GROMMET, rubber, 3/8 inch ID, console harness
11	68530C1	2	BOLT, Hex Flg, 1/4″-20 x 3/4″, Serr, BOLT hex flange, 1/4 NC x 3/4 inch
12	231-5144	2	NUT, Flg, USR, 1/4″-20
14	1310827C2	1	SWITCH, lockout, third gear
15	470-10620	2	SCREW, Slotted Pan Hd, #6-32 x 1 1/4″, machine, pan head slotted, No. 6 NC x 1-1/4 inch
16	495-31016	2	WASHER, #6
17	231-14106	2	NUT, LOCK, #6-32, GB, hex, self-locking, No. 6 NC
1	1994715C1	1	HARNESS, cab roof
2	3063674R1	1	GROMMET, blower harness
3	245175C1	1	SWITCH, door dome lamp control
4	168822C2	1	SWITCH, blower
5	109311H	1	NUT, hex, jam, 7/16 inch NF
6	111282C1	3	KNOB, KNOB control, blower, wiper and thermostat switch
7	245734C1	1	SWITCH, wiper control
8	109311H	1	NUT, hex, jam, 7/16 inch NF
9	111267C4	1	SWITCH, air conditioner, low pressure
10	109268C2	1	SWITCH, cab thermostat
11	109311H	2	NUT, hex, jam, 7/16 inch NF
12	245555C1	1	LAMP, 40 x 7 Halogen
13	325-148	6	NUT, Jam, 1/2″-13, G5, hex, jam, 1/2 inch NC
14	245897C91	5	LIGHT, WORK, LAMP Halogen, 80 x 30
15	1283449C3	1	BRACKET, lamp mounting, includes shield, right hand
16	1983391C1	1	LAMP, ASSEMBLY dome, parts list Fig. 4-30
17	A14553	4	BULB, No. 57, cab instrument panel and warning lamp
18	1281975C1	4	BRACKET, SUPPORT instrument panel bulb mounting
19	260-5448	4	SCREW, SELF TAPPING, Cross Pan Hd, #8 x 1/2″, Phillips
20	111619C1	6	STRAP, tie, adjustable
21	109740A1	1	WIPER MOTOR, ASSEMBLY includes mounting bracket, parts list Fig. 4-54
22	1255876C1	1	RESISTOR, blower motor
23	142990C2	1	MOTOR, ELECTRIC, blower, 12 volt, DC, PM, see Fig. 9G-38 for mounting
24	1281876C1	1	BRACKET, outer flood lamp mounting, left hand
25	492-21050	1	WASHER, LOCK, 1/2″
26	413-816	1	BOLT, Hex, 1/2″-13 x 1″, G5, Full Thd
27	1983394C2	1	RELAY, electrical, 12 volt, air conditioner, replaces 146461C1
28	169850C2	7	CLIP, CABLE, CLIP retaining, harness plastic
29	130882C91	1	LIGHT, INTERIOR, ASSEMBLY warning, parts list Fig. 4-30
30	198824C1	1	GROMMET, rubber, 1/2 inch ID, lamp harness, right hand
31	198825C1	1	GROMMET, 5/8 inch ID, lamp harness, left hand
32	436746	2	SCREW, machine, special, No. 10 NF x 1/4 inch
33	225-13110	1	NUT, #10-24
34	198828C1	1	GROMMET, deck harness, right hand
36	260-53424	4	SCREW, SELF TAPPING, Cross Pan Hd, #8 x 1 1/2″, self-tapping, pan Phillips, No. 8-18 x 1-1/2 inch
38	1979628C1	1	PLATE, LARGE, dome lamp
40	370383R1	4	CLIP, CLAMP warning lamp
43	371036R1	1	CLIP, CLAMP retaining, rubber covered
44	413-58	1	BOLT, Hex, 5/16″-18 x 1/2″, G5, Full Thd, hex, 5/16 NC x 1/2 inch
45	492-11031	1	WASHER, LOCK, 5/16″
47	115400A1	1	HARNESS, ADAPTER cab roof harness to wiper motor
1	1994834C2	1	HARNESS, center, combine
2	299269C91	2	CLAMP, retaining, center harness
2	515-24317	6	CLAMP, 1 1/4″, Insul, 7/16″ Bolt, P-type, 1-1/4 inch ID, insulated retaining
2	363444R1	6	CLAMP, J, 9/16″ Insul, 3/8″ Bolt, retaining, harness
2	362666R1	6	CLIP, CLAMP retaining, harness
4	187736C1	1	CABLE, separator clutch valve, if used
6	245193C2	1	SENSOR, transducer, straw spreader
7	245365C1	2	TRANSMITTER, SENSOR monitor control, rotary air screen and beater , BSN JJC0105064
8	245365C1	1	TRANSMITTER, SENSOR monitor control, tailings auger , BSN JJC0105064
9	245410C1	1	TRANSMITTER, SENSOR monitor control, straw chopper
10	245364C1	1	SWITCH, SENSOR monitor control, shoe
11	187996C1	1	MAGNET, shoe sensor, transmitter
12	187998C2	1	ANGLE, SUPPORT shoe sensor, transmitter
13	434-58	2	BOLT, CARRIAGE, Short NK, 5/16″-18 x 1/2″, G5, Full Thd, BOLT carriage, 5/16 NC x 1/2 inch
15	1252494C2	1	TRANSMITTER, SENSOR engine RPM, if used
17	178800C1	2	MAGNET, sensor, tailings auger and beater, if used
19	425-1512	2	NUT, Jam, 3/4″-10, G5, hex, jam, 3/4 inch NF
25	196987C1	1	MAGNET, sensor, rotary air screen, if used
26	263-5448	2	SCREW, SELF TAPPING, Slotted Pan Hd, #8 x 1/2″, self-tapping, pan slotted, No. 8-18 x 1/2 inch
27	1329865C1	1	CHANNEL, sensor mounting, rotary air screen , BSN JJC0105064
28	116892A1	1	CHANNEL, sensor mounting, rotary air screen , ASN JJC0105064
29	477-73112	3	BOLT, Slotted Tr Hd, 5/16″-18 x 3/4″, BOLT serrated, slotted truss head, 5/16 NC x 3/4 inch
31	495-11034	1	WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch, if used
34	1301560C1	1	SUPPORT, BRACKET mounting, rotary air screen adjustment, if used
36	413-512	1	BOLT, Hex, 5/16″-18 x 3/4″, G5, Full Thd, hex, 5/16 NC x 3/4 inch, if used
37	492-11031	1	WASHER, LOCK, 5/16″, If used
38	425-105	1	NUT, 5/16″-18, G5, If Used
44	178801C1	1	COLLAR, locking, bearing, tailing elevator , BSN JJC0105064
45	455102R21	1	COLLAR, locking, bearing, includes set screw, tailing elevator shaft , ASN JJC0105064
46	187615C3	1	SUPPORT, BRACKET tailings sensor, if used
47	181208C3	1	SUPPORT, COVER sensor, tailings, if used
48	280-1478	3	SCREW, SELF TAPPING, Hex Wash Hd, 1/4″ x 1/2″, self tapping, hex washer head, 1/4-14 x 1/2 inch
60	187629C1	1	SUPPORT, BRACKET sensor, beater shaft, if used
61	187630C1	1	SUPPORT, COVER sensor, beater shaft, if used
62	470-1086	4	SCREW, Slotted Pan Hd, #8-32 x 3/8″, machine, pan head slotted, No. 8 NC x 3/8 inch
63	492-11008	4	WASHER, LOCK, #8
64	280-1478	1	SCREW, SELF TAPPING, Hex Wash Hd, 1/4″ x 1/2″, self tapping, hex washer head, 1/4-14 x 1/2 inch
1	245245C2	1	HARNESS, header lift handle
2	91926C1	1	SWITCH, header lift control
11	1977143C3	1	GAUGE ASSY., MONITOR power boost, 15 PSI
12	222-5115	1	ELBOW, 90є, 5/16″-24 x 1/8″ NPTF, 90 degree, compression, 1/8 tube O.D. x 1/8 inch PT, if used
13	1977140C1	1	TUBE, 204 inch (5182 mm) long, cut from 1954063C1 bulk tube, engine to monitor, see this Figure
14	1977102C1	1	FITTING, CONNECTOR tube retaining, power boost monitor
15	1977142C1	1	CONDUIT, harness and tubing, power boost monitor
18	368-10810	2	SCREW, Slotted Oval Hd, #8-32 x 5/8″, machine, oval head slotted, No. 8 NC x 5/8 inch, power boost
19	392-11008	2	WASHER, LOCK, #8, #8, power boost monitor
20	225-13108	2	NUT, #8-32, Power boost monitor
23	1979103C2	1	ANGLE, BRACKET monitor support, power boost monitor
24	313-58	1	BOLT, Hex, 5/16″-18 x 3/8″, G5, Full Thd, BOLT hex, 5/16 NC x 1/2 inch, power boost monitor
25	1989678C1	1	FITTING, REDUCER, 7/8 PT x 1/8 inch female PT, replaces 221-87, power boost monitor
26	1979215C1	1	TAPE, ADHESIVE, adhesive, not shown, power boost monitor
27	28791R1	1	BULB, LAMP, No. 161, monitor, power boost monitor
1	245243C3	1	HARNESS, grain tank
3	91436C4	1	SWITCH, unloader in, grain tank harness
4	440-11012	2	SCREW, Cross Pan Hd, #10-24 x 3/4″, machine, pan Phillips, No. 10 NC x 3/4 inch, grain tank harness
5	225-14110	2	NUT, #10-24, Grain tank harness
6	493-81001	2	WASHER, LOCK, Ext-Int Tooth, #10, internal-external tooth lock, 3/16 inch, grain tank harness
7	1338022C1	1	SUPPORT, BRACKET unloader in switch, grain tank harness
8	68530C1	2	BOLT, Hex Flg, 1/4″-20 x 3/4″, Serr, BOLT hex flange, 1/4 NC x 3/4 inch, grain tank harness
9	231-5144	2	NUT, Flg, USR, 1/4″-20, Grain tank harness
10	370383R1	6	CLIP, CLAMP harness, grain tank harness
19	362123R1	7	CLIP, harness, grain tank
20	413-512	14	BOLT, Hex, 5/16″-18 x 3/4″, G5, Full Thd, hex, 5/16 NC x 3/4 inch, grain tank harness
21	492-11031	14	WASHER, LOCK, 5/16″, Grain tank harness
22	425-105	14	NUT, 5/16″-18, G5, Grain tank harness
23	537641R2	1	SWITCH, limit, unloader out, grain tank harness
24	490-1108	2	SCREW, Cross Pan Hd, #10-32 x 1/2″, machine, pan Phillips, No. 10 NF x 1/2 inch, grain tank harness
25	225-13210	2	NUT, #10-32, Grain tank harness
27	1338003C1	1	BRACKET, SUPPORT unloader out switch, grain tank harness
28	1338004C1	1	BRACKET, unloader out switch, grain tank harness
29	384557R1	1	CLIP, CLAMP P-type, harness, grain tank
30	198823C1	1	GROMMET, rubber, 3/8 inch ID, grain bin, grain tank harness
31	195803C1	2	GROMMET, 3/8 inch, grain tank harness, upper
41	91828C1	1	HARNESS, unloader lamp
43	299277C91	2	CLIP, CLAMP harness, unloader lamp harness
44	413-512	2	BOLT, Hex, 5/16″-18 x 3/4″, G5, Full Thd, hex, 5/16 NC x 3/4 inch, unloader lamp harness
45	492-11031	2	WASHER, LOCK, 5/16″, Unloader lamp harness
46	425-105	2	NUT, 5/16″-18, G5, Unloader lamp harness
26	493-81000	2	WASHER, LOCK, Ext-Int Tooth, #10, internal-external tooth, 3/16 inch, grain tank harness
1	1994847C1	1	HARNESS, rear lamps and fuel sender
2	363444R1	9	CLAMP, J, 9/16″ Insul, 3/8″ Bolt, retaining, harness
3	130882C91	2	LIGHT, INTERIOR, ASSEMBLY warning, rear, parts list Fig. 4-30
4	92260C1	2	LAMP, ASSEMBLY tail, parts list Fig. 4-30
5	198024C1	1	GAUGE, FUEL, SENSOR fuel level sending unit, parts list Fig. 3-14
1	245240C1	1	HARNESS, WIRE, rotor limit switch, BSN JJC0106005
3	186057C1	2	SWITCH, rotor limit switch harness, BSN JJC0106005
4	186058C1	2	SWITCH, IGNITION, ACTUATOR rotor limit switch harness,, BSN JJC0106005
5	470-10620	4	SCREW, Slotted Pan Hd, #6-32 x 1 1/4″, machine, pan head slotted, No. 6 NC x 1-1/4 inch, rotor limit
6	225-14106	4	NUT, #6-32, Rotor limit switch harness, BSN JJC0106005
7	138526	4	WASHER, internal tooth lock, special, No. 6, rotor limit switch harness, BSN JJC0106005
10	116494C1	1	SCREW, Sltd Serr Truss Hd, 3/8″-16 x 1/2″, Rotor limit switch harness , BSN JJC0106005
11	231-5146	1	NUT, Flg, USR, 3/8″-16, Rotor limit switch harness, BSN JJC0106005
12	495-31016	2	WASHER, #6, Rotor limit switch harness, BSN JJC0106005
21	1983397C1	1	HARNESS, fan and rotor speed,, BSN JJC0105560
1	113982A2	1	HARNESS, fan and rotor speed, replaced by 175949A1, Ref. 1A and 245240C1, Ref. 1B
3	128298A1	2	SWITCH, IGNITION, rotor limit
5	470-10620	4	SCREW, Slotted Pan Hd, #6-32 x 1 1/4″, machine, pan head slotted, No. 6 NC x 1-1/4 inch
6	225-14106	4	NUT, #6-32
7	138526	4	WASHER, internal tooth lock, special, No. 6
10	116494C1	1	SCREW, Sltd Serr Truss Hd, 3/8″-16 x 1/2″
11	231-5146	1	NUT, Flg, USR, 3/8″-16
12	495-31016	2	WASHER, #6
1	103898A1	1	CABLE, HARNESS feeder reverser
2	453453C1	1	SWITCH, push button, feeder reverser
3	245927C91	1	MOTOR, STARTER, ASSEMBLY feeder reverser, parts list Fig. 4-46
5	261-1478	2	SCREW, SELF TAPPING, Cross Pan Hd, 1/4″ x 1/2″, self-tapping, pan Phillips, 1/4 NC x 1/2 inch
6	103843A1	1	CABLE, battery positive
7	515-23254	10	CLAMP, 1″, Insul, 3/8″ Bolt, P-type, Cable retaining
9	413-636	3	BOLT, Hex, 3/8″-16 x 2 1/4″, G5
10	231-5146	3	NUT, Flg, USR, 3/8″-16
11	178148A1	1	COVER, solenoid switch, starting
12	183038A1	1	SWITCH, SOLENOID, SWITCH with barrier, replaces A39079
13	225-14210	1	NUT, #10-32
14	425-105	2	NUT, 5/16″-18, G5
15	492-11010	1	WASHER, LOCK, #10
16	492-11031	2	WASHER, LOCK, 5/16″
17	L18337	2	STRAP, CABLE, 9.95″-12.1″ lg, tie, nylon
2	A42294	1	SEALED BEAM UNIT, sealed beam, No. 4406
3	A25213	1	RETAINER, sealed lamp rubber, shockproof use with Hobbs lamp
3	1252609C1	1	RETAINER, shockproof, use with Midwest lamp
4	530029R91	1	CONNECTOR, lamp
5	1267358C2	1	SEAT, lamp mounting
6	80679	1	WASHER, LOCK, 1/2″
7	425-108	1	NUT, 1/2″-13, G5
8	154273C1	1	BOLT, Hex Flg, 3/8″-16 x 1″, Serr, BOLT hex, self-locking, special, 3/8 NC x 1 inch
9	1317942C1	1	BRACKET, grain tank lamp
10	231-5146	1	NUT, Flg, USR, 3/8″-16
1	1329859C1	2	BRACKET, flood lamp
2	1330144C1	1	GROMMET, wire
3	1330145C1	1	BUSHING, bracket
4	91938C1	1	LIGHT, INTERIOR, LAMP flood
5	92015C1	1	BRACKET, flood lamp
6	A149798	1	FUSE, tan, 5 ampere
6	A149799	1	FUSE, brown, 7-1/2 ampere
7	261-1456	2	SCREW, SELF TAPPING, Cross Pan Hd, #10 x 3/8″
8	265-1358	2	SCREW, SELF TAPPING, Cross Oval Hd, #10 x 1/2″, self tapping, oval Phillips, No. 10-16 x 1/2 inch
9	28753R1	1	LIGHT, LAMP sealed beam, No. 7604
1	130882C91	4	LIGHT, INTERIOR, ASSEMBLY warning, lamp, front and rear, Includes: Ref. 2 thru 6
2	130883C1	1	LENS, amber, warning lamp front and rear
3	A41264	1	BULB, #1156, 12V, Warning, front and rear
4	231-51409	2	NUT, Flg, USR, #10-24
5	261-54536	2	SCREW, SELF TAPPING, Cross Pan Hd, #10 x 2 1/4″, self-tapping, pan Phillips, No. 10 NC x 2-1/4
7	92260C1	2	LAMP, ASSEMBLY stop and tail, Includes: Ref. 8 thru 12
8	216045C1	1	LENS, red, stop and tail lamp
9	T34857	1	BULB, C6, #1157, 12.8V, lamp, No. 1157, stop and tail
10	231-51409	2	NUT, Flg, USR, #10-24, Stop and tail lamp
11	261-54536	2	SCREW, SELF TAPPING, Cross Pan Hd, #10 x 2 1/4″, self-tapping, pan Phillips, No. 10 NC x 2-1/4
14	1983391C1	1	LAMP, ASSEMBLY dome, Includes: Ref. 15
15	1094378R1	1	BULB, J, 12V, 2W, BULB, dome
16	1979628C1	1	PLATE, LARGE, dome lamp
17	260-53424	4	SCREW, SELF TAPPING, Cross Pan Hd, #8 x 1 1/2″, self tapping, pan Phillips, No. 8-18 x 1-1/2 inch
1	1983214C1	1	CONTROL BLOCK, automatic feeder cutoff
2	1983212C1	1	CONTROL BLOCK, automatic reel speed to ground speed
4	245637C1	1	POTENTIOMETER, single, 2.5K, reel to ground speed ratio
5	245925C1	1	POTENTIOMETER, single, 1K, speed setting
6	245638C1	1	POTENTIOMETER, single, 200K, calibration
7	245697C1	1	SWITCH, automatic manual, rocker
8	1301036C1	1	BUTTON, KNOB control, without pointer
9	1345235C1	1	BUTTON, KNOB control, with pointer
10	495-11041	1	WASHER, 3/8″, SAE, Flat, (13/32 x 13/16 x 1/16″)
11	245923C1	1	HARNESS, reel to ground speed
12	1280158C2	1	PANEL, control, front, parts list Fig. 9G-16
13	265-13516	4	SCREW, SELF TAPPING, Cross Oval Hd, #10 x 1″, self-tapping, oval Phillips, No. 10-16 x 1 inch
14	1329968C1	4	WASHER, oval head, finishing, No. 10
15	281-1476	4	SCREW, SELF TAPPING, Hex Wash Hd, 1/4″ x 3/8″, self-tapping, hex washer head, 1/4 NC x 3/8 inch
16	1994836C1	1	HARNESS, automatic feeder cutoff
17	1983394C2	1	RELAY, electrical, 12 volt, 30 ampere, replaces 146461C1
18	281-6456	1	SCREW, SELF TAPPING, Hex Wash Hd, #10 x 3/8″, self-tapping, hex washer head, No. 10 NF x 3/4
19	342-10610	2	SCREW, Cross Oval Hd, #6-32 x 5/8″, machine, oval Phillips, No. 6 NC x 5/8 inch
1	91479C2	1	CASE, KIT module, automatic header height control
2	281-1476	2	SCREW, SELF TAPPING, Hex Wash Hd, 1/4″ x 3/8″, self tapping, hex washer head, 1/4 NC x 3/8 inch
3	245385C1	1	POTENTIOMETER, single, 1K, header height control
4	245925C1	1	POTENTIOMETER, single, 1K, sensitivity control
5	1301036C1	2	BUTTON, KNOB control, without pointer
5	1345235C1	2	BUTTON, KNOB control, with pointer
6	113513A1	1	HARNESS, automatic header height
7	1983394C2	1	RELAY, electrical, 12 volt, 30 ampere, replaces 146461C1
8	245012C1	1	SWITCH, rocker, automatic header control, ON-OFF
10	1994842C1	1	HARNESS, automatic header height control hose
11	1331312C1	1	HARNESS, WIRE, extension, automatic header height control, if equipped
12	91795C1	1	SUPPORT, BRACKET connector mounting
13	363-31016	2	SCREW, Hex Wash Hd, #10-24 x 1″, machine, hex washer head, No. 10 NC x 1″
14	231-51409	2	NUT, Flg, USR, #10-24, (Replaces 174097C1)
15	281-6456	1	SCREW, SELF TAPPING, Hex Wash Hd, #10 x 3/8″, self tapping, hex washer head, No. 10 NF x 3/4
16	225290C1	1	DUST CAP, COVER plug
1	245237C1	1	HARNESS, cab, grain scan
2	1994838C1	1	HARNESS, main sensor
3	245930C2	1	HARNESS, chaffer sensor, 1550 mm (61.023 in)
3	92047C1	1	HARNESS, chaffer sensor, Used With Chaffer Extension, 2200 mm (86.614 in)
4	245360C3	1	CASE, MONITOR grain scan, new
5	326-412	2	BOLT, Hex, 1/4″-20 x 3/4″, G8, Full Thd
6	1280160C2	1	SUPPORT, BRACKET monitor mounting
7	179454C1	2	WASHER, flat, rubber, special
8	299565C1	1	CLAMP, P-type, 11/16 inch ID, harness closed
10	313-58	2	BOLT, Hex, 5/16″-18 x 3/8″, G5, Full Thd, BOLT hex, 5/16 NC x 1/2 inch
11	245361C2	2	TRANSMITTER, BLOCK chaffer sensor
12	413-532	4	BOLT, Hex, 5/16″-18 x 2″, G5
13	231-5145	12	NUT, Flg, USR, 5/16″-18
17	245884C1	1	TRANSMITTER, BLOCK grain sensor
19	A38799	2	CLAMP, P-type, retaining
20	245362C1	2	TRANSMITTER, BLOCK rotor sensor
21	135270	6	BOLT, Slotted Tr Hd, 5/16″-18 x 3/4″, slotted truss head, 5/16 NC x 3/4 inch
22	260-1356	4	SCREW, SELF TAPPING, Cross Pan Hd, #10 x 3/8″, self tapping, pan Phillips, No. 10-16 x 3/8 inch
23	440-10610	4	SCREW, Cross Pan Hd, #6-32 x 5/8″, machine, pan Phillips, No. 6 NC x 5/8 inch
24	493-11014	4	WASHER, LOCK, Ext-Int Tooth, #6, internal external tooth, 1/8 inch
25	225-14106	4	NUT, #6-32
26	245738C2	1	CLAMP, retaining
27	195806C1	1	GROMMET, left hand side sheet
29	515-2395	8	CLAMP, 3/8″, Insul, 3/8″ Bolt, Retaining
29	515-2595	2	CLAMP, 3/8″, Insul, 1/2″ Bolt, P-type
30	1301242C1	1	BRACKET, retaining
1	1994837C1	1	HARNESS, shaft speed rear
2	245193C2	4	SENSOR, transducer, feeder, ground speed, rotor, and fan
3	245275C91	1	CASE ASSY., MONITOR shaft speed, includes decal, Includes: Ref. 4 and 5
5	178876C1	1	SUPPRESSOR, audible alarm
6	245365C1	1	TRANSMITTER, SENSOR monitor control, clean grain sensor , BSN JJC0105064
8	178800C1	1	MAGNET, sensor, clean grain, if used
9	84116C1	1	NUT, hex, self locking, 3/4 inch NF
10	183869C3	1	SUPPORT, BRACKET sensor, clean grain, if used
11	1319397C1	1	COLLAR, locking, clean grain auger , BSN JJC0105064
12	280-1478	4	SCREW, SELF TAPPING, Hex Wash Hd, 1/4″ x 1/2″, self tapping, hex washer head, 1/4-14 x 1/2 inch
13	1979323C1	1	SHIELD, COVER clean grain auger sensor
14	245242C1	1	HARNESS, ASSEMBLY shaft speed front, Includes: Ref. 15
15	131498C1	2	CONNECTOR, ELEC, harness
16	1317973C2	1	SPROCKET ASSY., feeder sensor, with rock trap, if used
17	470-1086	3	SCREW, Slotted Pan Hd, #8-32 x 3/8″, machine, pan head slotted, No. 8 NC x 3/8 inch
18	492-11008	3	WASHER, LOCK, #8
19	483-1256	1	SET SCREW, Hex Soc, 1/4″-20 x 3/8″, set, hex socket headless, 1/4 NC x 3/8 inch, cup point
20	1330063C1	1	SUPPORT, sensor, feeder shaft, with rock trap, if after
21	434-512	2	BOLT, CARRIAGE, Short NK, 5/16″-18 x 3/4″, G5, Full Thd
22	1317950C1	1	SUPPORT, sensor, feeder, without rock trap
1	121604C1	1	GAUGE, ELECTRICAL, fuel
3	121605C2	1	GAUGE, ELECTRICAL, coolant temperature
4	121606C1	1	GAUGE, ELECTRICAL, oil pressure
5	121607C1	1	METER, GAUGE system voltage, engine
6	121608C1	1	BEZEL + GASKET, instrument cluster
7	187597C1	1	LENS, warning lamp, coolant level
8	1979357C1	1	LENS, warning lamp, coolant level
9	121611C1	8	SOCKET, bulb, instrument cluster
10	D71346	8	LAMP, TAIL, lamp, No. 168
11	265-13512	4	SCREW, SELF TAPPING, Cross Oval Hd, #10 x 3/4″, self tapping, oval Phillips, No. 10-16 x 3/4 inch
13	265-13512	4	SCREW, SELF TAPPING, Cross Oval Hd, #10 x 3/4″, self tapping, oval Phillips, No. 10-16 x 3/4 inch
14	1987322C2	1	TACHOMETER, engine
15	265-13512	4	SCREW, SELF TAPPING, Cross Oval Hd, #10 x 3/4″, self tapping, oval Phillips, No. 10-16 x 3/4 inch
2	A149801	2	FUSE, light blue, 15 ampere
3	A149800	5	FUSE, red, 10 ampere
4	A149804	1	FUSE, light green, 30 ampere
5	A149798	2	FUSE, tan, 5 ampere
6	A149796	2	FUSE, violet, 3 ampere
7	A149799	3	FUSE, brown, 7-1/2 ampere
10	1280162C3	1	SUPPORT, fuse block
11	937875R1	2	SCREW, Sltd Serr Truss Hd, 1/4″-20 x 3/4″, slotted truss head, 1/4 NC x 3/4 inch
12	231-5144	2	NUT, Flg, USR, 1/4″-20
13	281-1478	2	SCREW, SELF TAPPING, Hex Wash Hd, 1/4″ x 1/2″, self tapping, hex washer head, 1/4 NC x 1/2 inch
14	245435C1	3	FUSE HOLDER, BLOCK part of console harness
15	506504C1	1	CONNECTION, TERMINAL fuse block, type L10
16	506498C1	1	CONNECTION, TERMINAL fuse block, type L11
1	BMF31G	2	BATTERY, DRY, 12V, Electrical supply
2	S115407	1	BOOT, rubber, battery cable, positive cable at starter solenoid
3	103842A1	1	CABLE, ASSEMBLY battery, positive, Includes: Ref. 4 and 5
12	92023C3	1	CABLE, ASSEMBLY battery, ground, Includes: Ref. 13 and 14
16	363660R1	1	CLIP, CLAMP battery positive cable
17	299414C1	1	CLAMP, 7/8″, Insul, 1/4″ Bolt, CLAMP battery positive cable
19	158477C91	2	CABLE, ground, engine to combine
20	413-632	1	BOLT, Hex, 3/8″-16 x 2″, G5
21	492-11038	1	WASHER, LOCK, 3/8″
22	425-106	1	NUT, 3/8″-16, G5
25	702093C1	2	STRAP, CABLE, tie, cable retaining
27	A187523	1	BLOCK, CONNECTING, cable junction
28	128289A1	2	SCREW, BOLT battery cable, special
29	231-5145	2	NUT, Flg, USR, 5/16″-18
1	194267C6	1	TRAY, battery
2	135270	4	BOLT, Slotted Tr Hd, 5/16″-18 x 3/4″, slotted truss head, 5/16 NC x 3/4 inch
3	231-5145	4	NUT, Flg, USR, 5/16″-18
4	194266C1	1	SUPPORT, battery tray
7	188116C1	1	CLAMP, battery hold down
8	411-5152	2	BOLT, CARRIAGE, Short NK, 5/16″-18 x 9 1/2″, G2, BOLT carriage, 5/16 NC x 9-1/2 inch, grade 2
9	495-11034	2	WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch
10	129-419	2	NUT, WING, 5/16″-18, 5/16 inch NC, replaces 523193R1
1	A187728	1	MOTOR, STARTER, ASSEMBLY engine, parts list Figs. 4-50 and 4-52, and mounting
2	868-12035	3	SCREW, 12 Pt Hd, M12 x 35, 12.9, BOLT 12 point flange, 12 – 1.75 x 35 mm, class 12.9, starter
3	892-11012	3	WASHER, LOCK, M12, Starter Mounting
4	492-11010	1	WASHER, LOCK, #10, Starter mounting
5	225-14210	1	NUT, #10-32, Starter mounting
6	495-11053	1	WASHER, 1/2″, SAE, (17/32″ x 1-1/16″ x 3/32″), Starter mounting
7	425-108	1	NUT, 1/2″-13, G5, Starter mounting
8	896-11012	3	WASHER, M13.5 x 24.5 x 3, HT, Starter Mounting
8	91448C2	1	ALTERNATOR, ASSEMBLY engine, 110 ampere, parts list Fig. 4-48, alternator mounting
9	A189616	1	PULLEY, alternator mounting
10	854-12065	1	BOLT, Hex Flg, M12 x 65, 10.9, BOLT heavy hex flange, 12 – 1.75 x 65 mm, class 10.9, alternator
11	854-12050	1	BOLT, Hex Flg, M12 x 50, 10.9, Alternator mounting
12	829-2312	2	NUT, M12 x 1.75, Flg, Cl 10, hex flange, 12 mm – 1.75, class 10, alternator mounting
13	J911485	1	SUPPORT, BRACE alternator, mounting
14	614-8030	1	BOLT, Hex, M8 x 30, 8.8, Full Thd, Alternator mounting
15	360-820	1	BOLT, Hex Flg, 1/2″-13 x 1 1/4″, G8, Full Thd, BOLT hex flange, 1/2 NC x 1-1/4 inch, grade 8
16	892-11008	1	WASHER, LOCK, M8, Alternator mounting
18	1979627C1	1	COVER, SCREEN alternator dust cover, mounting
19	681209C1	1	CLAMP, HOSE, #32, 1.56/2.50 Type F Worm, W/liner, adj, No. 32, type F, retaining, alternator mounting
20	1964826C1	1	GROMMET, alternator mounting
21	1338890C1	1	COVER, end, alternator mounting
22	825-1405	4	NUT, M5, Cl 8, Alternator mounting
23	892-11005	8	WASHER, LOCK, M5, Alternator mounting
24	495-31025	4	WASHER, 3/16″, flat, 1/4 x 9/16 x 3/64 inch, alternator mounting
25	425-147	1	NUT, Jam, 7/16″-14, G5, hex, jam, 7/16 inch NC, alternator mounting
26	492-11044	1	WASHER, LOCK, 7/16″, Alternator mounting
27	825-1404	1	NUT, M4, Cl 8, Alternator mounting
28	892-11004	1	WASHER, LOCK, M4, Alternator mounting
1	A186232	1	ARMATURE, MOTOR
2	A186233	1	HOUSING, BEARING, PLACE
3	3079432R1	1	BUSHING, CLUTCH
4	A186234	1	SEAL, PLATE bearing
5	A186235	1	CLUTCH, DRIVE
6	3079254R1	2	BUSHING, CLUTCH
7	3055738R1	1	BUSHING, LARGE, FRAME
8	3053133R1	1	WASHER, SEALING, M8 x 11.5 x 1, GASKET, vent screw, fork pivot
9	691265C1	1	NUT, hex, special, fork pivot
10	3079172R1	2	STUD, FRAME, motor
11	A186236	3	SCREW, flat head, special, retaining
12	A186237	1	RETAINER, RING bearing plate
13	A186238	1	COIL, field
14	3079552R1	4	BOLT, SCREW field coil
15	3079174R1	1	HOLDER, BRUSH
16	3079420R1	4	SPRING, BRUSH
17	A186239	1	COVER, SHIELD holder
18	3079170R1	1	BUSHING, LARGE, HOLDER
19	K965147	2	WASHER, flat
20	825-1406	2	NUT, M6, Cl 8
21	3079177R1	1	CAP, holder
22	K965146	2	SCREW, fillister head
23	A186240	2	WASHER, lock
24	825-1410	2	NUT, M10, Cl 8
25	A186241	1	CLAMP, SADDLE, cable
26	K965151	1	SCREW, SADDLE, clamp
27	A186243	2	WASHER, lock
28	933824R1	2	NUT, Thin, M4 x .5, Cl 04, hex, 4 mm
29	3079359R91	1	BRUSH, KIT, Includes: Ref. 30, 31, and 32
33	3078965R1	1	LEVER, FORK clutch drive
34	3079430R1	1	BOLT, SCREW fork pivot
35	A186246	1	FRAME, SHIELD drive end
36	A186244	1	SWITCH, solenoid
37	A186245	1	DIAPHRAGM, solenoid
1	1964731C1	1	HOUSING, collector ring end
3	1964737C1	1	BUSHING, expansion
4	3079389R1	1	CAPACITOR, suppression, alternator
5	684857C1	1	SCREW, fillister head, capacitor retaining
6	A186196	1	WASHER, special, retaining screw
9	1964733C1	1	REGULATOR, ASSEMBLY voltage, Includes: Ref. 10 and 11
10	3079394R91	1	SET, BRUSHES, alternator
11	1964734C1	2	SPRING, compression
12	A186194	2	SCREW, Sltd Truss Hd, M4 x 18, w/LW, BOLT hex flange, special, regulator retaining
13	1964738C1	1	KIT, REPAIR, KIT terminal hardware
16	1964732C1	1	RECTIFIER, alternator
17	A187504	2	SCREW, hex flange, special, rectifier bridge retaining
18	1964735C1	1	STATOR, alternator
19	1964728C1	1	ROTOR, alternator
20	3079410R1	1	RING, collector
21	1964730C1	1	BEARING, BALL
22	495-51066	1	WASHER, 9/16″ x 1 1/4″ x .1″, flat, 21/32 x 1-1/4 x 3/32 inch
23	231-46110	1	NUT, LOCK, 5/8″-18, GB
26	1964727C1	1	PLATE, bearing retaining
27	1964726C1	1	BEARING, BALL, drive end
28	1964725C1	1	HOUSING, drive end
29	1964748C1	4	SCREW, BOLT fillister head, special, slotted, alternator retaining
30	1964750C1	4	SCREW, machine, flat head, special, retaining
31	1964729C1	1	SPACER, ring
32	1964736C1	1	FAN, alternator
34	A189616	1	PULLEY, alternator
1	A187851	1	HOUSING, FRAME ASSEMBLY end, commutator, Includes: Ref. 2 and 3
4	845-6060	2	BOLT, Hex Flg, M6 x 60, 8.8, BOLT heavy hex flange, 6 – 1.0 x 60 mm
5	825-2306	2	NUT, M6 x 1, Flg, Cl 8, hex flange, 6 mm – 1
8	A187857	4	O-RING, sealing
13	A187852	1	BRUSH HOLDER, ASSEMBLY, Includes: Ref. 14
14	A187823	4	SPRING, brush
15	A187794	4	BRUSH, starter
16	A47816	4	SCREW, slotted, includes lock washer, 5 – 0.8 x 12 mm
17	A47813	1	WASHER, end, armature
18	A187847	1	ARMATURE, starter
22	A187846	1	HOUSING ASSY., field coil, Includes: Ref. 23 thru 33
34	A187862	1	NUT, hex, terminal
35	A187858	1	FITTING, CONNECTOR, terminal B
37	829-1410	1	NUT, M10, Cl 10
38	A187859	1	WASHER, wave
39	425-108	1	NUT, 1/2″-13, G5
41	A187860	1	WASHER, plate, armature
42	A187850	1	HOUSING, ASSEMBLY lever, Includes: Ref. 43 and 44
48	A187865	1	KIT, pin, lever
52	A49815	4	WASHER, lock, bolt
53	A187861	4	SCREW, BOLT hex, housing 7 x 23 mm
54	A187848	1	CLUTCH ASSEMBLY, starter drive
55	A187855	1	NUT, pinion stop
58	A47790	1	SNAP RING, collar to shaft
59	A187853	1	LEVER, ASSEMBLY clutch, starter, Includes: Ref. 60
60	A187854	2	PAD, WEAR, lever
61	A47786	1	O-RING, clutch housing
62	A187849	1	HOUSING, ASSEMBLY clutch drive, Includes: Ref. 63
64	A187856	6	SCREW, BOLT hex, special, drive housing
66	A187864	1	COVER, KIT anti-bypass start, terminal, Includes: Ref. 67
68	A187863	1	SWITCH, SOLENOID, ASSEMBLY magnetic, Includes: Ref. 69 thru 73
65	814-6040	2	BOLT, Hex, M6 x 40, 8.8
1	109740A1	1	WIPER MOTOR, ASSEMBLY includes mounting bracket, Includes: Ref. 2 thru 9
2	739487C1	2	CLIP, spring, Part of KIT, part number1267542C91
3	148074R1	2	WASHER, flat, hardened, 6.0 x 14.4 x 0.4 mm, retaining, Part of KIT, part number1267542C91
4	1267556C1	1	BUTTON, NUT knurled drive, Part of KIT, part number1267542C91
10	1321282C1	1	ARM, wiper, 18 inch (457 mm)
11	1327520C1	1	BLADE, WIPER, 22 inch (559 mm)
12	412-416	1	BOLT, CARRIAGE, Short NK, 1/4″-20 x 1″, G2, BOLT carriage, 1/4 NC x 1 inch, grade 2
13	425-104	1	NUT, 1/4″-20, G5
14	1327763C1	2	SCREW, hex washer head, 3/8 NC x 3/4 inch
15	425-106	2	NUT, 3/8″-16, G5
16	492-11038	2	WASHER, LOCK, 3/8″
17	492-11025	1	WASHER, LOCK, 1/4″
1	111381C1	1	KNOB, control, volume, Part of KIT, part number 84226C91
2	111382C1	1	KNOB, control, tuning, Part of KIT, part number 84226C91
3	385532C1	2	KNOB, control, tone and balance, Part of KIT, part number 84226C91
4	245344C91	1	RADIO, AM
4	245160C91	1	RADIO, AM-FM stereo
5	142921C1	4	NUT, hex, special
6	142920C1	2	WASHER, flat, 9.72 x 15.00 x 0.60 mm
7	425-144	1	NUT, Jam, 1/4″-20, G5
8	492-11025	1	WASHER, LOCK, 1/4″
9	117995C1	3	PACKAGE, KIT fastener, toggle type, contains 5 fasteners, Part of KIT, part number 84226C91
10	1276052C1	14	SCREW, SELF TAPPING, Cross Oval Hd, #8 x 1 3/4″, self tapping, oval head, No. 8-18 x 1-3/4 inch
11	1280182C2	1	PANEL, radio trim
13	84103C1	1	PANEL, radio trim highlight, Part of KIT, part number 84226C91
14	91484C1	1	PLATE, radio support, Part of KIT, part number 84226C91
15	280-14510	4	SCREW, SELF TAPPING, Hex Wash Hd, #10 x 5/8″, self tapping, hex washer head, No. 10-16 x 5/8
16	84048C1	1	BRACKET, radio support, rear side, Part of KIT, part number 84226C91
17	280-1458	2	SCREW, SELF TAPPING, Hex Wash Hd, #10 x 1/2″, self tapping, hex washer head, No. 10-16 x 1/2
18	84049C1	1	BRACKET, radio support, rear, Part of KIT, part number 84226C91
19	245806C1	2	PANEL, speaker grille, Part of KIT, part number 84226C91
20	245343C1	2	SPEAKER, radio, 5 x 7 inch, 4 ohm, Part of KIT, part number 84226C91
21	60-6490T1	1	ANTENNA, radio, Part of KIT, part number 84226C91
22	1321384C1	1	PANEL, radio insert
23	436746	2	SCREW, machine, special, No. 10 NF x 1/4 inch
24	195-513	2	WASHER, #10, flat, 7/32 x 1/2 x 3/64 inch
25	84240C1	2	SPACER, 3/8 x 5/8 x 3/4 inch, Part of KIT, part number 84226C91
26	1964513C1	1	HARNESS, adapter
1	1987377C1	1	SWITCH, grain tank level
2	458-532	2	BOLT, Hex Flg, 5/16″-18 x 2″, G5, BOLT hex flange, 5/16 NC x 2 inch
3	121606A1	2	SPACER, pipe, 1/4 x 1 inch
4	231-5145	2	NUT, Flg, USR, 5/16″-18
1	1327540C3	1	CHANNEL, steering post cover
2	1321449C1	1	SECTOR, RACK steering column pivot
3	1327550C4	1	SUPPORT, PEDESTAL steering column
4	1327551C1	1	CHANNEL, steering post cover
5	413-572	1	BOLT, Hex, 5/16″-18 x 4 1/2″, G5, BOLT hex, 5/16 NC x 4-1/2 inch
6	193235C3	1	PIVOT, release, steering
7	193239C2	1	BAR, PLATE steering release
8	87435C1	1	MOLDING, TRIM edge, 3 inch (76 mm) long, cut from 1330108CX bulk trim, see this Figure
9	183608C1	1	SPRING, pedal return
10	413-8120	1	BOLT, Hex, 1/2″-13 x 7 1/2″, G5, hex, 1/2 NC x 7-1/2 inch
11	1324844C1	1	SEAL, steering pedestal
12	1283223C2	1	SUPPORT, steering pump
13	1321442C1	1	TUBE, steering column pivot
14	1321441C1	1	SPACER, steering column
15	1327546C1	1	COVER, steering column, upper, front
16	1327547C4	1	COVER, steering column, upper, rear
17	193263C1	1	SUPPORT, steering pivot stop pin
18	1542690C1	1	PUMP, ASSEMBLY steering hand, parts list Fig. 5-8
19	1321683C1	1	WHEEL (STEERING)
20	1329895C2	1	CAP ASSY., steering wheel
21	1321447C1	17	SCREW, SELF TAPPING, Cross Pan Hd, 1/4″-20 x 1/2″, self tapping, pan Phillips, 1/4 NC x 1/2 inch
22	1321448C1	6	BOLT, CARRIAGE, Hex, 5/16″-18 x 3/4″, G5, carriage, 5/16 NC x 3/4 inch
23	231-5145	8	NUT, Flg, USR, 5/16″-18
24	232-4115	1	NUT, LOCK, 5/16″-18, GC
25	68530C1	2	BOLT, Hex Flg, 1/4″-20 x 3/4″, Serr, BOLT hex flange, 1/4 NC x 3/4 inch
26	231-5144	2	NUT, Flg, USR, 1/4″-20
27	231-4118	1	NUT, LOCK, 1/2″-13, GB, hex, self-locking, 1/2 inch NC
28	135270	2	BOLT, Slotted Tr Hd, 5/16″-18 x 3/4″, slotted truss head, 5/16 NC x 3/4 inch
29	413-636	1	BOLT, Hex, 3/8″-16 x 2 1/4″, G5
30	495-11041	2	WASHER, 3/8″, SAE, Flat, (13/32 x 13/16 x 1/16″)
31	231-5146	2	NUT, Flg, USR, 3/8″-16
32	326-8128	1	BOLT, Hex, 1/2″-13 x 8″, G8, BOLT hex, 1/2 NC x 8 inch, grade 8
33	396-41053	2	WASHER, 17/32″ x 1 1/4″ x .188″, HDN, flat, 17/32 x 1-1/4 x 3/16 inch, hardened
34	232-4118	1	NUT, LOCK, 1/2″-13, GC
35	1327574C1	4	BOLT, Hex Flg, Ser, 5/16″-18 x 1/4″, G5, hex flange, polyseal, 5/16 NC x 1/2 inch, Includes: Ref. 37
36	1282041C91	1	SHAFT ASSY., COLUMN steering
37	934727R1	1	NUT, Thin, M18 x 1.5, Cl 04, hex, special
38	409-7612	2	BOLT, Hex Flg, 3/8″-16 x 3/4″, Serr
39	409-7620	2	BOLT, Hex Flg, 3/8″-16 x 1 1/4″, Serr
40	561277R1	2	SPACER, 5/8″ Tube x 1/2″, 13/32 x 5/8 x 7/16 inch
41	353-406	2	PLUG, Dome, .625″ hole, Nylon, button, 5/8 inch
42	159716C1	1	SPACER, 3/4″ Tube x 5/8″, tubular, 17/32 x 3/4 x 9/16 inch
1	1542690C1	1	PUMP, ASSEMBLY steering hand, parts list Fig. 5-8
2	201-106	1	CONNECTOR, HYD., 11/16″-16 ORFS x 3/4″-16 ORB, ADAPTER straight, 11/16-16 face seal x 3/4-16
3	237-6008	1	O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk, Includes ref. 3 and 4
4	238-6012	1	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
5	201-319	1	ELBOW, 90є, 11/16″-16 x 1/16″-16 Fem Sw ORFS, 90 degree, 11/16-16 inch face seal x swivel face
6	238-6012	1	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
7	1989505C1	1	HOSE, 39 inch (990 mm) long, steering hand pump return, Foot-N-Inch, see Fig. 6-12 for continuation
8	201-345	1	ELBOW, 90є, 11/16″-16 x 3/4″-16, Adj, ORFS, 90 degree, 11/16-16 face seal x 3/4-16 inch adj O-ring
9	237-6008	1	O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
10	238-6012	1	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
11	1989504C1	1	HOSE, 86 inch (2185 mm) long, steering hand pump supply, steering diagnostic tee
12	1541791C1	1	TEE, special, steering diagnostic, Includes: Ref. 13
13	238-6012	1	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
15	1541849C1	1	COUPLING, ASSEMBLY diagnostic, to check pressure, order 1543171C1, see this Figure, Includes:
17	H434163	1	DUST CAP, dust, coupler
18	238-6012	1	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
19	1989287C2	1	TUBE, steering pressure
20	201-126	2	CONNECTOR, HYD., 13/16″-16 ORFS x 9/16″-20 ORB, straight, 13/16-16 face seal x 9/16-18 inch
21	238-6014	1	O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
23	1994631C2	1	LIMITER, ATTENUATOR, 0.7 liter
24	1541627C1	1	ELBOW, special, restrictor
26	238-6014	1	O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
27	1989363C2	1	HOSE, 43-5/16 inch (1100 mm) long, steering pressure
28	87029955	2	CLAMP, 7/8″, Insul, 3/8″ Bolt, adj, 2-13/16 – 3-3/4 inch diameter
14	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
16	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
22	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
25	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
1	1542690C1	1	PUMP, ASSEMBLY steering hand, hydrostatic steering, parts list Fig. 5-8
2	218-5058	1	CONNECTOR, HYD., 9/16″-18, 37є x 3/4″-18, O-Ring, ADAPTER straight, 9/16-18 flare x 3/4-16 inch
3	237-6008	1	O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
4	111174A1	1	HOSE ASSY., 135 inch (3420 mm) long, steering hand pump, left hand
5	218-5128	1	ELBOW, 90є, 9/16″-18, 37є x 3/4″-16, O-Ring, Adj.
6	237-6008	1	O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
7	139519C2	1	HOSE, 135 inch (3429 mm) long, steering hand pump, right hand
8	1541565C1	2	TUBE, steering, intermediate
9	196791C1	2	TUBE ASSY., steering, rear
10	179202C1	1	HOSE, 68 inch (1727 mm) long, cylinder, lower
11	178962C1	1	HOSE ASSY., 60 inch (1524 mm) long, cylinder, upper
11	183920C1	1	HOSE ASSY., 77 inch (1956 mm) long, cylinder, upper, 120 inch axle
12	218-5105	2	ELBOW, 90є, 9/16″-18, 37є x 9/16″-18, O-Ring, 90 degree, 9/16-18 inch flare x adj O-ring boss
14	548247R91	1	CYLINDER ASSY., 2 (51) ID x 9 inch (229 mm) stroke, steering, without power guide axle, parts list
14	127913C93	1	CYLINDER STEERING, ASSEMBLY, 2-1/4 (57) ID x 9 inch (229 mm) stroke, steering, with power
15	183825C1	3	CLAMP, steering tube, for 3/8 inch
16	413-428	1	BOLT, Hex, 1/4″-20 x 1 3/4″, G5, hex, 1/4 NC x 1-3/4 inch
17	413-436	2	BOLT, Hex, 1/4″-20 x 2 1/4″, G5
18	231-5144	3	NUT, Flg, USR, 1/4″-20
19	178960C1	1	BRACKET, SUPPORT steering rear tube
20	409-7612	1	BOLT, Hex Flg, 3/8″-16 x 3/4″, Serr
21	231-5146	2	NUT, Flg, USR, 3/8″-16
22	167955C2	2	SEAL, GROMMET steering cylinder hose
23	165602C1	1	CLAMP, steering tube
24	163490C1	2	INSULATOR, RUBBER, INSULATOR rubber, 3/8 ID x 1-13/64 inch long, steering tube clamp
25	231-5145	2	NUT, Flg, USR, 5/16″-18
26	535789R1	1	BOLT, Hex Flg, 5/16″-18 x 1 1/4″, Serr, BOLT hex flange, 5/16 NC x 1-1/4 inch
27	183899C1	1	ANGLE, support, hand pump hose
28	409-7512	1	BOLT, Hex Flg, 5/16″-18 x 3/4″, Serr
29	196517C1	1	SUPPORT, steering tube
30	409-7612	1	BOLT, Hex Flg, 3/8″-16 x 3/4″, Serr
31	413-572	1	BOLT, Hex, 5/16″-18 x 4 1/2″, G5, BOLT hex, 5/16 NC x 4-1/2 inch
32	495-81116	1	WASHER, .344″ x 1″ x .060″, flat, 11/32 x 1 x 3/64 inch
33	26613R1	1	CLAMP, 1 7/8″, Insul, 1/2″ Bolt, 1-7/8 inch diameter, steering hose
34	492-11031	1	WASHER, LOCK, 5/16″
35	425-105	1	NUT, 5/16″-18, G5
36	167955C2	2	SEAL, GROMMET power steering hoses
37	111863A1	1	STRAP, BRACKET steering hose support
38	111862A1	1	SUPPORT, steering hose
39	413-616	1	BOLT, Hex, 3/8″-16 x 1″, G5, Full Thd, hex, 3/8 NC x 1 inch
40	231-5146	1	NUT, Flg, USR, 3/8″-16
41	306132C1	2	STRAP, CABLE, .30″ x 14.5″, tie, 14 inch, pump hoses
13	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
2	3112271R1	1	PIN, ROLL, 2 x 32 mm
3	3216710R1	6	SCREW, BOLT hex, 8 – 1.25 x 40 mm
4	1272805C1	1	COVER, end
6	1272803C1	1	PLATE, pump, gear
7	1272802C1	1	SPACER, shaft
8	1272797C1	1	SHAFT, drive, pump
9	1272796C1	1	PIN, LARGE, dowel, special, 6 x 41 mm
10	1272793C1	1	BUSHING, threaded, housing
11	1272794C1	1	BALL, check, 8.5 mm diameter
12	1272795C1	1	RING, O, sleeve, seal
13	1272809C1	1	PACKAGE, KIT spring, set of four
14	1272808C1	1	KIT, needle bearing
1	548247R91	1	CYLINDER ASSY., 2 (51) ID x 9 inch (229 mm) stroke, steering, Includes: Ref. 2 thru 6

Pages: 1 2 3 4 5 6

Leave a Reply Cancel reply