CASE IH Axial – Flow Combine 1666

admin October 16, 2016 No Comments

CASE IH Axial – Flow Combine 1666 — parts list, part 3 of 6

Assemblies on this page: Parts list (continued) … Parts list (continued).

Parts list (continued)

Pos	Part no.	Qty	Description
13	237-6008	1	O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
14	238-6014	1	O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
15	127779C94	2	CYLINDER, header lift, see Fig. 8-34
16	1989343C1	1	ANGLE BAR, tube support
17	409-7612	2	BOLT, Hex Flg, 3/8″-16 x 3/4″, Serr
18	231-5146	2	NUT, Flg, USR, 3/8″-16
19	1989653C1	1	SUPPORT, header cylinder fitting
20	299413C1	1	CLAMP, hose, closed coated, header lift
21	413-432	1	BOLT, Hex, 1/4″-20 x 2″, G5
22	495-11028	1	WASHER, 1/4″, SAE, flat, 9/32 x 5/8 x 1/16 in.
23	231-5144	1	NUT, Flg, USR, 1/4″-20
24	299269C91	1	CLAMP, retaining, single, header lift and steering hose
25	425-1410	1	NUT, Jam, 5/8″-11, G5, hex, jam, 5/8 in. NC
26	470375C1	2	CLAMP, double header lift and steering hose
3	127780C2	1	ROD, PISTON header lift cylinder
5	142568C2	1	HEAD, GLAND cylinder, front, header lift cylinder
25	A47221	1	SEAL, RING sealing, included with 1282338C91, hydraulic couplings
1	1541613C1	1	SUPPORT, BRACKET mounting, valve, front, stack
2	1989370C2	2	SUPPORT, BRACKET mounting, valve, rear, stack end
3	231-5144	6	NUT, Flg, USR, 1/4″-20
4	107981A2	6	VALVE, ASSY., unload, single bi-directional, reel lift, see Fig. 8-40
5	1267035C94	1	VALVE, ASSY., double piloted, unloader swing, see fig. 8-42, no longer available, order 124857A1
5	124857A1	1	VALVE, ASSY., double piloted, unloader swing, see Fig. 8-43A, ASN JJC105314
6	1542678C1	1	VALVE, ASSY., flow divider, see Fig. 8-44
7	1542679C2	1	VALVE, ASSY., header lift, see Fig. 8-46, Includes: Ref. 8 thru 11
8	107957A1	1	POPPET, VALVE, raise check
9	107959A1	1	SPRING, poppet
10	238-6016	2	O-RING, -016, 90 Duro, .614″ ID x .070″ Thk
11	A34493	2	RING, backup, large tube
12	1542680C3	1	VALVE, ASSY., header, lower, see Fig. 8-48, replaces 1542680C2
13	1542681C1	1	VALVE, ASSY., feeder clutch, see Fig. 8-50
14	1301630C2	9	TUBE, through, small, Includes: Ref. 15 and 16
15	238-6012	2	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
16	L31330	2	RING, backup
17	1301634C2	4	PLUG, cap, small, Includes: Ref. 18 and 19
18	238-6012	1	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
19	L31330	1	RING, backup
20	107984A1	1	PISTON, TUBE through, large, includes seals, Includes: Ref. 21 and 22
21	238-6016	2	O-RING, -016, 90 Duro, .614″ ID x .070″ Thk
22	A34493	2	RING, backup, large tube O-ring
23	107985A1	1	PISTON, PLUG, cap, large, includes seals, Includes: Ref. 24 and 25
24	238-6016	2	O-RING, -016, 90 Duro, .614″ ID x .070″ Thk
25	A34493	2	RING, backup, large tube O-ring
26	106439A1	3	STEM, ROD tie, valve sections, used, on models without field tracker attachment, There is one large
27	201-104	1	CONNECTOR, HYD., 1 3/16″-12 ORFS x 1 1/16″-12 ORB, Includes Ref. 28 and 29
28	237-6012	1	O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk
29	238-6018	1	O-RING, -018, 90 Duro, .739″ ID x .070″ Thk
30	1272346C1	1	FILTER, inline, valve pressure line, Includes: Ref. 31
31	237-6012	1	O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk
32	218-5320	2	ELBOW, 90є, 7/16″-20, 37є x 3/4″-16, O-Ring, 90 deg., 7/16-20 flare x 3/4-16 in. adj. O-ring boss
33	237-6008	1	O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
34	201-125	1	CONNECTOR, HYD., 11/16″-16 ORFS x 7/16″-20 ORB, ADAPTER straight, 11/16-16 face seal x
35	238-6012	1	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
36	237-6004	1	O-RING, 4-1, 90 Duro, .351″ ID x .072″ Thk
37	201-106	1	CONNECTOR, HYD., 11/16″-16 ORFS x 3/4″-16 ORB, ADAPTER straight, 11/16-16 face seal x 3/4-16
38	237-6008	1	O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
39	238-6012	1	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
40	201-321	1	ELBOW, 45є, 13/16″-16 x 9/16″-18. Adj, ORFS, 45 deg., 13/16-16 face seal x 9/16-18 in. adj. O-ring
42	238-6014	1	O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
43	201-350	1	ELBOW, 90є, 1 3/16″-12 x 7/8″-14, Adj, ORFS, 90 deg., 1-3/16-12 face seal x 7/8-14 in. adj. O-ring
44	238-6018	1	O-RING, -018, 90 Duro, .739″ ID x .070″ Thk
45	237-6010	1	O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
46	1989475C3	1	TEE, special, 5/8 O-ring boss adj., 3/4 x 3/8 in., Includes: Ref. 47
47	237-6010	1	O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
48	1541849C1	1	COUPLING, ASSY., diagnostic, Includes: Ref. 49 and 50
49	H434163	1	DUST CAP, dust, coupler
51	201-412	1	TEE, 13/16″-16 x 3/4″-16 Run, ORFS, 13/16-16 face branch x face x 3/4-16 in. adj. O-ring, Includes:
52	237-6008	1	O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
53	238-6014	2	O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
41	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
50	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
1	1541613C1	1	SUPPORT, BRACKET mounting, valve, front
2	1989370C2	2	SUPPORT, BRACKET mounting, valve, rear
3	231-5144	6	NUT, Flg, USR, 1/4″-20
5	107981A2	1	VALVE, ASSY., unload, single bi-directional, reel lift see Fig. 8-40
6	1267035C94	1	VALVE, ASSY., double piloted, unloading swing, see Fig. 8-42, no longer available, order 124857A1
6	124857A1	1	VALVE, ASSY., double piloted, unloader swing, see Fig. 8-43A, ASN JJC105314
7	1267035C94	1	VALVE, ASSY., double piloted, reel for and aft, see Fig. 8-42, no longer available, prder 124857A1
7	124857A1	1	VALVE, ASSY., double piloted, reel for and aft, see Fig. 8-43A, ASN JJC105314
8	1542678C1	1	VALVE, ASSY., flow divider, see Fig. 8-44
9	1542679C2	1	VALVE, ASSY., header lift, see Fig. 8-46, Includes: Ref. 10 thru 13
10	107957A1	1	POPPET, VALVE, raise check
11	107959A1	1	SPRING, poppet
12	238-6016	2	O-RING, -016, 90 Duro, .614″ ID x .070″ Thk
13	A34493	2	RING, backup, large tube O-ring
14	1542680C3	1	VALVE, ASSY., header, lower, see Fig. 8-48, replaces 1542680C2
15	1542681C1	1	VALVE, ASSY., feeder clutch, see Fig. 8-50
16	1301630C2	9	TUBE, through, small, Includes: Ref. 17 and 18
17	238-6012	2	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
18	L31330	2	RING, backup
19	1301634C2	4	PLUG, cap, small, Includes: Ref. 20 and 21
20	238-6012	1	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
21	L31330	1	RING, backup
22	107984A1	1	PISTON, TUBE through, large, includes seals., Includes: Ref. 23 and 24
23	238-6016	2	O-RING, -016, 90 Duro, .614″ ID x .070″ Thk
24	A34493	2	RING, backup, large tube O-ring
25	107985A1	1	PISTON, PLUG cap, large, includes seals, Includes: Ref. 26 and 27
26	238-6016	2	O-RING, -016, 90 Duro, .614″ ID x .070″ Thk
27	A34493	2	RING, backup, large tube O-ring
28	106440A1	3	STEM, ROD tie, valve sections, used on models without field tracker attachment, There is one large
29	201-104	1	CONNECTOR, HYD., 1 3/16″-12 ORFS x 1 1/16″-12 ORB, Includes Ref. 30 and 31
30	237-6012	1	O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk
31	238-6018	1	O-RING, -018, 90 Duro, .739″ ID x .070″ Thk
32	1272346C1	1	FILTER, inline, valve pressure line, Includes: Ref. 33
33	237-6012	1	O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk
34	218-5320	2	ELBOW, 90є, 7/16″-20, 37є x 3/4″-16, O-Ring, 90 deg., 7/16-20 flare x 3/4-16 in. adj. O-ring boss
35	237-6008	1	O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
36	201-125	1	CONNECTOR, HYD., 11/16″-16 ORFS x 7/16″-20 ORB, ADAPTER straight, 11/16-16 face seal x
37	238-6012	1	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
38	237-6004	1	O-RING, 4-1, 90 Duro, .351″ ID x .072″ Thk
39	201-106	2	CONNECTOR, HYD., 11/16″-16 ORFS x 3/4″-16 ORB, ADAPTER straight, 11/16-16 face seal x 3/4-16
40	237-6008	1	O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
41	238-6012	1	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
42	201-321	1	ELBOW, 45є, 13/16″-16 x 9/16″-18. Adj, ORFS, 45 deg., 13/16-16 face seal x 9/16-18 in. adj. O-ring
44	238-6014	1	O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
45	201-350	1	ELBOW, 90є, 1 3/16″-12 x 7/8″-14, Adj, ORFS, 90 deg., 1-13/16-12 face seal x 7/8-14 in. adj. O-ring
46	238-6018	1	O-RING, -018, 90 Duro, .739″ ID x .070″ Thk
47	237-6010	1	O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
48	1989475C3	1	TEE, special, 5/8 O-ring boss adj. x 3/4 x 3/8 in., Includes: Ref. 49
49	237-6010	1	O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
50	1541849C1	1	COUPLING, ASSY. diagnostic, Includes: Ref. 51 and 52
51	H434163	1	DUST CAP, dust, coupler
53	201-106	2	CONNECTOR, HYD., 11/16″-16 ORFS x 3/4″-16 ORB, ADAPTER straight, 11/16-16 face seal x 3/4-16
54	237-6008	1	O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
55	238-6012	1	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
56	201-412	1	TEE, 13/16″-16 x 3/4″-16 Run, ORFS, 13/16-16 face branch x face x 3/4-16 in. adj. O-ring, Includes:
57	237-6008	1	O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
58	238-6014	2	O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
43	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
52	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
2	107966A1	1	SEAT, poppet
3	238-6015	1	O-RING, -015, 90 Duro, .551″ ID x .070″ Thk, , Part includesvalve seal kit 1282280C1
4	238-5018	1	O-RING, -018, 70 Duro, .739″ ID x .070″ Thk, , Part includesvalve seal kit 1282280C1
5	107970A1	1	POPPET, VALVE
6	107967A1	2	SPRING, poppet
7	237-6010	1	O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk, , Part includesvalve seal kit 1282280C1
8	107968A1	1	PLUG, hex, special, end
9	238-6019	2	O-RING, -019, 90 Duro, .801″ ID x .070″ Thk, , Part includesvalve seal kit 1282280C1
10	1301641C2	1	SLEEVE, TRANSMISSION, poppet, solenoid valve
11	1301642C1	1	WASHER, spring, retaining
12	1301643C1	1	VALVE, ARMATURE
13	1301644C1	1	PIN, POPPET valve, Order 1301644C2. Also Order BUSHING 1301646C2 and SLEEVE 1301641C2
14	1301821C1	1	SPRING, poppet
15	1301646C1	1	BUSHING, poppet, armature
16	1301639C1	1	PISTON, ORIFICE valve, 0.022 in. opening
17	238-6010	1	O-RING, -010, 90 Duro, .239″ ID x .070″ Thk, , Part includesvalve seal kit 1282280C1
18	1301627C1	1	STUD, SLEEVE poppet, solenoid valve
19	1301640C1	1	SPRING, poppet, sleeve
20	110550A1	1	POPPET, VALVE
21	1301648C1	1	ARMATURE, valve
22	1301624C1	1	BUSHING, poppet, armature
23	1346430C1	1	RESTRICTOR, ORIFICE valve, 0.062 in. opening
24	238-6010	1	O-RING, -010, 90 Duro, .239″ ID x .070″ Thk, , Part includesvalve seal kit 1282280C1
25	1301632C1	2	CAP, COVER coil
26	1301633C1	2	COIL, valve
27	107825	2	NUT, Stamped, 1/2″-20, hex, 1/2 in. NF
28	225-20210	2	NUT, #10-32, Brass
2	1301686C1	2	CAP, PLUG hex, special, end
3	1301689C1	2	SPRING, spool, plug
4	237-6010	2	O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
5	238-6019	2	O-RING, -019, 90 Duro, .801″ ID x .070″ Thk
6	238-6010	2	O-RING, -010, 90 Duro, .239″ ID x .070″ Thk
7	238-6014	1	O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
8	238-6114	1	O-RING, -114, 90 Duro, .612″ ID x .103″ Thk
10	1301687C1	2	RETAINER, RETAINER spring
11	1301627C2	2	SLEEVE, poppet, valve
12	1301642C1	2	WASHER, spring, retaining
13	1301640C1	2	SPRING, poppet, sleeve
14	110550A1	2	POPPET, VALVE
15	1301648C1	2	ARMATURE, valve
16	1301624C1	2	BUSHING, poppet, piole
17	1301625C1	2	ORIFICE, valve
19	238-6114	1	O-RING, -114, 90 Duro, .612″ ID x .103″ Thk
21	1267160C2	2	VALVE, POPPET
22	238-6014	1	O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
24	1267162C1	1	VALVE, POOL shuttle
26	1301637C1	2	ORIFICE, ORIFICE valve
27	1301632C1	2	CAP, hex, 1/2 in. NF
28	1301633C1	2	COIL, valve
29	107825	2	NUT, Stamped, 1/2″-20, hex, 1/2 in. NF
30	225-20210	2	NUT, #10-32, Brass
9	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk, Not used in this application, not shown
2	100475A1	2	PLUG, end cap
3	100474A1	2	SPRING, centering, plug
4	237-6010	2	O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
5	238-6019	2	O-RING, -019, 90 Duro, .801″ ID x .070″ Thk, Not used in this application, not shown
6	238-6010	2	O-RING, -010, 90 Duro, .239″ ID x .070″ Thk
7	238-6014	1	O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
8	238-6114	1	O-RING, -114, 90 Duro, .612″ ID x .103″ Thk
10	1301687C1	2	RETAINER, RETAINER spring
11	1301627C2	2	SLEEVE, poppet, valve
12	1301642C1	2	WASHER, spring, retaining
13	1301640C1	2	SPRING, poppet, sleeve
14	110550A1	2	POPPET, VALVE
15	1301648C1	2	ARMATURE, valve
16	1301624C1	2	BUSHING, poppet, pole
17	1301625C1	2	ORIFICE, valve
18	124775A1	2	CAP, BODY check valve
19	238-6114	2	O-RING, -114, 90 Duro, .612″ ID x .103″ Thk
20	1272887C1	2	SPRING, poppet
21	124771A1	2	POPPET, VALVE
22	238-6014	2	O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
23	1267163C1	2	SEAT, valve
24	124777A1	1	SPOOL, shuttle
26	238-8019	2	O-RING, -019, Cl 8, .801″ ID x .070″ Thk
27	1301632C1	2	CAP, COVER coil
28	1301633C1	2	COIL, valve
29	107825	2	NUT, Stamped, 1/2″-20, hex, 1/2 in. NF
30	225-20210	2	NUT, #10-32, Brass
9	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk, Not used in this application, not shown
2	1301674C1	1	NUT, hex, special, 1 in.
3	1301675C1	1	SCREW, PLUG valve
4	1301677C1	1	PIN, GUIDE spring
5	211-1008	1	BALL, 1/4″ Dia, chrome alloy steel, 1/4 in., grade 24
6	237-6010	1	O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
7	1301636C1	1	SPRING, poppet
8	238-6014	1	O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
9	1301654C1	1	NUT, ORIFICE valve
10	1301679C1	1	SPRING, orifice
11	1301678C1	1	VALVE, POPPET, end
15	1301686C1	1	CAP, PLUG hex, special
16	237-6010	1	O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
17	107961A1	1	SPRING, spool
18	1301662C1	1	WASHER, RETAINER spring
19	107975A1	1	SPOOL, valve
20	9625178	1	PLUG, Hex Soc, 9/16″-18 ORB, Incl. Ref. 21
26	105945A1	1	PORT, DISC field tracker, if used, not shown
21	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
2	1301657C1	1	PISTON, ORIFICE valve, poppet
3	238-6015	1	O-RING, -015, 90 Duro, .551″ ID x .070″ Thk
4	238-5018	2	O-RING, -018, 70 Duro, .739″ ID x .070″ Thk
5	107956A1	1	POPPET, VALVE, piston
6	1301660C1	1	SPRING, poppet
7	237-6010	1	O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
8	1301661C1	1	PLUG, hex
9	238-6019	1	O-RING, -019, 90 Duro, .801″ ID x .070″ Thk
10	1301646C2	1	BUSHING, LARGE, poppet, pole
11	1301644C2	1	SPOOL, valve
12	1301643C1	1	VALVE, ARMATURE
13	1301642C1	1	WASHER, spring, retaining, backup
14	1301641C2	1	SLEEVE, TRANSMISSION, poppet
15	1301730C1	1	VALVE, COIL
16	1301632C1	1	CAP, COVER coil
17	107825	1	NUT, Stamped, 1/2″-20, hex, 1/2 in. NF
18	1301821C1	1	SPRING, poppet
19	107965A1	1	PORT, ORIFICE valve
20	238-6010	1	O-RING, -010, 90 Duro, .239″ ID x .070″ Thk
21	107953A1	1	NEEDLE, OVERRIDE ASSY., manual, includes O-ring and backup ring
22	107955A1	1	PLUG, GUIDE valve
23	L31750	1	CIRCLIP, 0.562″, Int, #56, 0.562″, Int, #56
24	425-154	1	NUT, Jam, 1/4″-28, G5
25	107969A1	1	WASHER, flat, special
26	107962A1	1	SEAT, valve
27	237-6008	1	O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
29	107957A1	1	POPPET, VALVE
30	107959A1	1	SPRING, poppet
31	238-6016	1	O-RING, -016, 90 Duro, .614″ ID x .070″ Thk
32	A34493	1	RING, backup
33	225-20210	1	NUT, #10-32, Brass
2	1301730C1	1	VALVE, COIL
3	1301632C1	1	CAP, COVER coil
4	107825	1	NUT, Stamped, 1/2″-20, hex, 1/2 in. NF
5	1301627C3	1	SLEEVE, poppet
7	1301640C1	1	SPRING, poppet
8	1301647C1	1	POPPET, poppet
9	1301648C1	1	ARMATURE, valve, support
10	1301624C1	1	BUSHING, poppet, pole
11	238-6019	1	O-RING, -019, 90 Duro, .801″ ID x .070″ Thk
12	1301625C1	1	ORIFICE, valve
14	238-6010	1	O-RING, -010, 90 Duro, .239″ ID x .070″ Thk
17	238-5018	1	O-RING, -018, 70 Duro, .739″ ID x .070″ Thk
18	107951A3	1	POPPET, VALVE, replaces 107951A2
19	1301665C1	1	PISTON, POPPET
20	238-5014	1	O-RING, -014, 70 Duro, .489″ ID x .070″ Thk
21	1301660C1	1	SPRING, poppet
22	107963A1	1	RETAINER, PLUNGER adjusting
23	238-5006	1	O-RING, -006, 70 Duro, .114″ ID x .070″ Thk
24	237-6010	1	O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
25	107958A1	1	PLUG, adjusting
26	329-156	1	NUT, Jam, 3/8″-24, G8
27	414-616	1	BOLT, Hex, 3/8″-24 x 1″, G5, Full Thd, BOLT hex, 3/8 NF x 1 in.
28	225-20210	1	NUT, #10-32, Brass
2	1301687C1	1	RETAINER, RETAINER spring
3	107960A1	1	SPRING, poppet
4	1301686C1	1	CAP, PLUG hex, special, end
5	237-6010	1	O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
7	107825	1	NUT, Stamped, 1/2″-20, hex, 1/2 in. NF
8	1301632C1	1	CAP, COVER coil
9	1301730C1	1	VALVE, COIL
10	1301648C1	1	ARMATURE, valve, support
11	238-6019	1	O-RING, -019, 90 Duro, .801″ ID x .070″ Thk
12	1301624C1	1	BUSHING, poppet, pole
13	1301627C2	1	SLEEVE, poppet
14	1301642C1	1	WASHER, spring, retaining, backup
15	1301640C1	1	SPRING, poppet
16	110550A1	1	POPPET, VALVE
17	1301625C1	1	ORIFICE, valve
18	238-6010	1	O-RING, -010, 90 Duro, .239″ ID x .070″ Thk
20	86625138	1	PLUG, Hex Soc, 7/8″-14 ORB, Includes Ref. 21
21	237-6010	1	O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
22	225-20210	1	NUT, #10-32, Brass
1	1994653C2	1	PUMP, ASSY., auxiliary drive, reel, see Fig. 8-56
2	1272619C93	1	VALVE, ASSY., hydraulic, reel drive, see Fig. 8-58
3	1541633C2	1	TEE, special, branch, feeder clutch valve, Includes: Ref. 4 and 5
4	238-6018	1	O-RING, -018, 90 Duro, .739″ ID x .070″ Thk
5	238-6014	1	O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
6	1541634C1	1	VALVE, ASSY., relief, pressure regulator, Includes: Ref. 7 and 8
7	237-6010	1	O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
8	238-6018	1	O-RING, -018, 90 Duro, .739″ ID x .070″ Thk
9	201-306	1	ELBOW, 90є, 1″-14 x 7/8″-14 Adj, ORFS, 90 deg., 1-14 face seal x 7/8-14 in. adj. O-ring boss
10	237-6010	1	O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
11	238-6016	1	O-RING, -016, 90 Duro, .614″ ID x .070″ Thk
12	201-420	1	TEE, 1″-14 x 7/8″-14 Run, ORFS, 1-14 face branch x face x 7/8-14 in, adj. O-ring boss, Includes: Ref.
13	238-6016	2	O-RING, -016, 90 Duro, .614″ ID x .070″ Thk
14	237-6010	1	O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
15	1541753C2	1	TUBE, reel drive valve supply, includes Ref. 45 O-ring
16	1980050C2	1	HOSE, reel pump to valve, 29 in. (737 mm) long
17	1989495C1	1	HOSE, reel motor supply, 136 in. (3455 mm) long
19	1345266C1	1	WASHER, lock, white, special
20	201-103	1	CONNECTOR, HYD., 1″-14 ORFS x 7/8″-14 ORB, Includes Ref. 21 and 22
21	238-6016	1	O-RING, -016, 90 Duro, .614″ ID x .070″ Thk
22	237-6010	1	O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
23	1272399C2	1	COUPLING, QUICK, MALE, self sealing, male, 7/8 in. NF
24	1989496C1	1	HOSE, reel drive motor return, 102-1/2 in. (2605 mm) long
25	201-306	1	ELBOW, 90є, 1″-14 x 7/8″-14 Adj, ORFS, 90 deg., 1-14 face seal x 7/8-14 in. adj. O-ring boss
26	237-6010	1	O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
27	238-6018	1	O-RING, -018, 90 Duro, .739″ ID x .070″ Thk, 5/8 ID x 1/16 in. wide
28	1282338C91	1	COUPLING, QUICK, FEMALE, self sealing, female, 7/8-14 in.
29	1989476C1	1	PIPE, TUBE return, reel drive
30	1989283C1	1	TUBE, valve return
31	424-564	1	BOLT, Hex, 5/16″-18 x 4″, G2, BOLT hex, 5/16 NC x 4 in., grade 2
32	1347127C1	4	PLATE, clamp, hose
33	1347072C1	1	CLAMP, tube, 3/4 in. O.D.
34	1989362C1	3	CLAMP, tube, two piece
35	231-4115	2	NUT, LOCK, 5/16″-18, GB
36	413-536	1	BOLT, Hex, 5/16″-18 x 2 1/4″, G5, hex, 5/16 NC x 2-1/4 in. NC
37	1541827C1	1	TEE, seperator clutch, special, Includes: Ref. 38, 39, and 40
38	237-6010	1	O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
39	238-6018	1	O-RING, -018, 90 Duro, .739″ ID x .070″ Thk
40	238-6012	1	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
41	196868C2	1	SUPPORT, PLATE
42	409-7512	2	BOLT, Hex Flg, 5/16″-18 x 3/4″, Serr
43	495-11034	1	WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 in.
44	231-5145	2	NUT, Flg, USR, 5/16″-18
45	238-6018	1	O-RING, -018, 90 Duro, .739″ ID x .070″ Thk
46	1541538C1	1	CLAMP, two piece, 3/4 in. O.D. tube
47	1541537C1	1	PLATE, clamp
48	413-436	2	BOLT, Hex, 1/4″-20 x 2 1/4″, G5
49	231-4144	2	NUT, LOCK, 1/4″-20, GB
1	1957656C3	1	SUPPORT, feeder hoses
2	1321990C1	1	CLAMP, coupling, ISO
3	68530C1	6	BOLT, Hex Flg, 1/4″-20 x 3/4″, Serr, BOLT hex flange, 1/4 NC x 3/4 in.
5	1321989C2	1	SUPPORT, coupling
6	231-5144	6	NUT, Flg, USR, 1/4″-20
7	1989500C1	1	SLEEVE, hose, cordura
8	306132C1	2	STRAP, CABLE, .30″ x 14.5″, tie, 14 in., nylon
10	1989477C1	1	SUPPORT, feeder hoses
11	434-620	2	BOLT, CARRIAGE, Short NK, 3/8″-16 x 1 1/4″, G5, Full Thd
13	432-620	4	PIN, SPLIT (COTTER), 3/32″ x 1 1/4″, 3/32″ x 1 1/4″
14	1954133C1	1	DUST CAP, coupling, dust, Includes: Ref. 15
15	401758R1	1	WASHER, dust plug
16	409-7612	2	BOLT, Hex Flg, 3/8″-16 x 3/4″, Serr
17	231-5146	4	NUT, Flg, USR, 3/8″-16
18	26613R1	3	CLAMP, 1 7/8″, Insul, 1/2″ Bolt, 1-7/8 in. dia., closed
19	409-7620	1	BOLT, Hex Flg, 3/8″-16 x 1 1/4″, Serr
20	231-5146	4	NUT, Flg, USR, 3/8″-16
21	515-23190	1	CLAMP, 3/4″, Insul, 3/8″ Bolt, P-type
22	409-7612	1	BOLT, Hex Flg, 3/8″-16 x 3/4″, Serr
1	1994653C2	1	PUMP, ASSY., auxiliary drive, header lift and reel drive, Includes: kits
2	1541733C1	1	PLATE, LARGE, SUPPORT auxiliary pump
3	231-5148	5	NUT, Flg, USR, 1/2″-13
4	409-7824	5	BOLT, Hex Flg, 1/2″-13 x 1 1/2″, Serr, BOLT hex serrated flange, 1/2 NC x 1-1/2 in.
5	413-840	4	BOLT, Hex, 1/2″-13 x 2 1/2″, G5, hex, 1/2 Nc x 2-1/2 in.
6	495-81164	12	WASHER, 17/32″ x 1 3/4″ x .179″, flat, 17/32 x 1-3/4 x 11/64 in.
7	231-4118	4	NUT, LOCK, 1/2″-13, GB, hex, self locking, 1/2 in. NC
8	R29799	4	SHOCK ABSORBER, INSULATOR rubber, mount
9	1541732C2	2	SUPPORT ASSY., isomount, auxiliary pump
10	413-624	6	BOLT, Hex, 3/8″-16 x 1 1/2″, G5
11	495-81135	12	WASHER, 13/32″ x 1″ x .120″, flat, 13/32 x 1 x 7/64 in.
12	492-11038	6	WASHER, LOCK, 3/8″
13	425-106	6	NUT, 3/8″-16, G5
14	1541737C1	1	SUPPORT, lower isomount
15	413-824	3	BOLT, Hex, 1/2″-13 x 1 1/2″, G5, Full Thd, hex, 1/2 NC x 1-1/2 in.
16	496-21053	3	WASHER, 17/32″ x 1 1/16″ x .134″, Hardened
17	231-5148	3	NUT, Flg, USR, 1/2″-13
18	1541736C1	1	SUPPORT, upper isomount
1	1272619C93	1	VALVE, ASSY., hydraulic, reel drive, Includes: Ref. 1 thru 26
3	92669C2	1	SWITCH, SOLENOID
4	114555A1	1	SOLENOID, COIL
5	1301632C1	1	CAP, COVER coil
6	107825	1	NUT, Stamped, 1/2″-20, hex, 1/2 in. NF
7	G108725	1	BACK-UP RING
9	238-6010	1	O-RING, -010, 90 Duro, .239″ ID x .070″ Thk
10	L31750	1	CIRCLIP, 0.562″, Int, #56, 0.562″, Int, #56
11	107969A1	1	WASHER, flat, special
12	425-154	1	NUT, Jam, 1/4″-28, G5
15	237-6010	1	O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk, Solenoid
17	G108725	1	BACK-UP RING
18	238-6010	1	O-RING, -010, 90 Duro, .239″ ID x .070″ Thk
19	237-6012	1	O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk
20	115466A1	2	PORT, ORIFICE valve, 0.025 in.
23	115467A1	1	SPRING, spool
24	62-3108	4	SCREW, Hex Soc Hd, #10-32 x 1/2″, BOLT hex socket, No. 10 NF x 1/2 in.
25	115468A1	1	CAP, PLUG hex, special, spool
26	115465A1	2	PORT, ORIFICE valve, 0.031 in.
27	413-540	2	BOLT, Hex, 5/16″-18 x 2 1/2″, G5, Replaced by 413-544 bolt and 495-8117 washer
27	413-544	2	BOLT, Hex, 5/16″-18 x 2 3/4″, G5, Replaces 413-540 bolt and 495-81117 washer
28	495-81123	2	WASHER, .344″ x 1 3/4″ x .079″, flat, 11/32 x 1-3/4 x 11/64 in., used with 443-540 or 413-544 bolt
29	231-5145	2	NUT, Flg, USR, 5/16″-18
16	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk, Solenoid
1	107981A2	1	VALVE, ASSY., unload, single bi-directional, reel lift, see Fig. 8-40, reel lift system
2	201-125	1	CONNECTOR, HYD., 11/16″-16 ORFS x 7/16″-20 ORB, ADAPTER straight, 11/16-16 face seal x
3	237-6004	1	O-RING, 4-1, 90 Duro, .351″ ID x .072″ Thk, Reel lift system
4	238-6012	1	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk, Reel lift system
5	1989470C1	1	HOSE, reel, left, 114 in. (2895 mm) long, reel lift system
6	201-362	1	ELBOW, 90є, 11/16″-16 x 7/8″-14, Adj, ORFS, ELBOW, 90 deg., 11/16-16 face seal x 7/8-14 in. adj.
7	237-6010	1	O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk, Reel lift system
8	238-6012	1	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk, Reel lift system
9	1282338C91	1	COUPLING, QUICK, FEMALE, self sealing, female, 7/8-14 in., reel lift system
10	1267035C94	1	VALVE, ASSY., double piloted, prior to P.I.N. JJC105314, see Fig. 8-42, no longer available, order
10	124857A1	1	VALVE, ASSY., double piloted, P.I.N. JJC 105314 and after, see Fig. 8-43A, reel for and aft syatem
11	201-106	2	CONNECTOR, HYD., 11/16″-16 ORFS x 3/4″-16 ORB, ADAPTER straight, 11/16-16 face seal x 3/4-16
12	237-6008	1	O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk, Reel fore and aft system
13	238-6012	1	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk, Reel fore and aft system
14	1282338C91	1	COUPLING, QUICK, FEMALE, self sealing, female, 7/8-14 in., reel fore and aft system
15	1272399C2	1	COUPLING, QUICK, MALE, self sealing, male, 7/8 in. NF, reel fore and aft system
16	201-362	1	ELBOW, 90є, 11/16″-16 x 7/8″-14, Adj, ORFS, ELBOW, 90 deg., 11/16-16 face seal x 7/8-14 in. adj.
17	237-6010	1	O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk, Reel fore and aft system
18	238-6012	1	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk, Reel fore and aft system
19	201-139	1	CONNECTOR, HYD., 11/16″-16 ORFS x 7/8″-14 ORB, ADAPTER straight, 11/16-16 face seal x 7/8-14
20	237-6010	1	O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk, Reel fore and aft system
21	238-6012	1	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk, Reel fore and aft system
22	1541792C1	1	WASHER, LOCK, lock, red, special, reel fore and aft system
23	1989470C1	1	HOSE, reel lift, 114 in. (2895 mm) long, reel fore and aft system
24	1989471C1	1	HOSE, reel aft, 150 in. (3810 mm) long, reel fore and aft system
25	515-23127	1	CLAMP, 1/2″, Insul, 3/8″ Bolt, P type, harness, closed, 1/2 in. ID, reel fore and aft system
26	409-7612	1	BOLT, Hex Flg, 3/8″-16 x 3/4″, Serr, Reel fore and aft system
27	231-5146	1	NUT, Flg, USR, 3/8″-16, Reel fore and aft system
1	1542681C1	1	VALVE, ASSY., feeder clutch, see Fig. 8-50
2	133405C92	1	CYLINDER, ASSY., feeder clutch, 2, 51, ID x 2-1/2 in. (63.5 mm) stroke, see Fig. 8-70
3	201-304	2	ELBOW, 90є, 11/16″-16 x 9/16″-18 Adj, ORFS, 90 deg., 11/16-16 face seal x 9/16-18 in. adj. O-ring
5	238-6012	1	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
6	1541793C1	2	HOSE, feeder clutch cylinder, 120 in. (3050 mm) long
7	201-106	2	CONNECTOR, HYD., 11/16″-16 ORFS x 3/4″-16 ORB, ADAPTER straight, 11/16-16 face seal x 3/4-16
9	238-6012	1	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
10	201-321	1	ELBOW, 45є, 13/16″-16 x 9/16″-18. Adj, ORFS, 45 deg., 13/16-16 face seal x 9/16-18 in. O-ring boss
12	238-6014	1	O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
13	1541573C2	1	HOSE ASSY., feeder clutch valve, 18-3/4 in. (475 mm) long
14	1541633C2	1	TEE, feeder clutch valve, special, branch, Includes: Ref. 15 and 16
15	238-6014	1	O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
16	238-6018	2	O-RING, -018, 90 Duro, .739″ ID x .070″ Thk
17	1541849C1	1	COUPLING, ASSY., diagnostic, Includes: Ref. 18 and 19
18	H434163	1	DUST CAP, dust, coupler
20	299264C91	1	CLAMP, P type, hose, feeder clutch system, not shown
4	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
8	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
11	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
19	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
1	1301171C91	1	VALVE, ASSY., feeder and separator clutch, see Fig. 8-68, control concepts
2	133408C92	1	CYLINDER, ASSY., separator clutch, 2, (51) ID x 12-1/2 in. (318 mm) stroke, control concepts
3	201-304	1	ELBOW, 90є, 11/16″-16 x 9/16″-18 Adj, ORFS, 90 deg., 11/16-16 face seal x 9/16-18 in. adj. O-ring
5	238-6012	1	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk, Control concepts
6	218-5057	2	CONNECTOR, HYD., 9/16″-18, 37є x 9/16″-18, O-Ring, Control concepts, Incl. Ref. 7
8	1280792C1	1	HOSE, separator clutch disengage, 20 in. (508 mm) long, control concepts
9	598931R91	1	HOSE, seperator clutch engage, 17 in. (432 mm) long, control concepts
10	1541716C1	1	HOSE, seperator clutch pressure, 35 in. (890 mm) long, control concepts
11	187619C2	1	HOSE, separator clutch return, 22 in. (559 mm) long, cut from 364357C1 bulk hose, see below, control
12	178036C1	1	CONNECTOR, ADAPTER straight, special, beaded tube, hose, 3/8 in. barb end x 9/16 in. PT, control
14	214-1704	2	CLAMP, HOSE, #4, 0.25/0.62 Type M Worm, Adjustable, Control concepts
15	238-6012	2	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk, Control concepts
17	218-5105	2	ELBOW, 90є, 9/16″-18, 37є x 9/16″-18, O-Ring, 90 deg., 9/16-18 in. flare x adj. O-ring boss, control
19	187505C91	1	VALVE, ASSY., feeder and separator clutch, see Fig. 8-68, modular controls
20	133408C92	1	CYLINDER, ASSY., separator clutch, 2 (51) ID x 12-1/2 in. (318 mm) stroke, modular controls
21	201-304	1	ELBOW, 90є, 11/16″-16 x 9/16″-18 Adj, ORFS, 90 deg., 11/16-16 face seal x 9/16-18 in. adj. O-ring
23	238-6012	1	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk, Modular controls
24	1280792C1	1	HOSE, separator clutch disengage, 20 in. (508 mm) long, modular controls
25	598931R91	1	HOSE, separator clutch engage, 17 in. (432 mm) long, modular controls
26	218-5057	2	CONNECTOR, HYD., 9/16″-18, 37є x 9/16″-18, O-Ring, Modular controls, Incl. Ref. 27
28	1541716C1	1	HOSE, separator clutch pressure, 35 in.(890 mm) long, modular controls
29	178036C1	1	CONNECTOR, ADAPTER straight, hose, special, 3/8 in. barb end x 9/16 in. PT, modular controls
31	187619C2	1	HOSE, separator clutch return, 22 in. (559 mm) long, cut from 364357C1 bulk, see below, modular
32	214-1704	2	CLAMP, HOSE, #4, 0.25/0.62 Type M Worm, Adjustable, Modular controls
34	238-6012	2	O-RING, -012, 90 Duro, .364″ ID x .070″ Thk, Modular controls
35	218-5105	2	ELBOW, 90є, 9/16″-18, 37є x 9/16″-18, O-Ring, 90 deg., 9/16-18 in. flare x adj. O-ring boss, modular
22	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk, 15/16 ID x 4/64 in. wide, modular controls
4	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk, Control concepts
7	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk, Control concepts
13	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk, Control concepts
18	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk, Control concepts
27	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk, Modular controls
30	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk, Modular controls
36	237-6006	1	O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk, Modular controls
1	187505C91	1	VALVE, ASSY., feeder and separator clutch, see Fig. 8-68, modular controls
2	187506C1	1	SUPPORT, separator clutch valve, modular controls
3	413-432	2	BOLT, Hex, 1/4″-20 x 2″, G5, Modular controls
4	495-81113	2	WASHER, .344″ x 3/4″ x .179″, flat, 11/32 x 3/4 x 3/16 in., modular controls
5	231-5144	4	NUT, Flg, USR, 1/4″-20, Modular controls
6	413-412	2	BOLT, Hex, 1/4″-20 x 3/4″, G5, Full Thd, Modular controls
9	1301171C91	1	VALVE, ASSY., feeder and separator clutch, see Fig. 8-68, control concepts
10	1301037C1	1	ANGLE, BRACKET mounting, separator clutch valve, control concepts
11	413-436	3	BOLT, Hex, 1/4″-20 x 2 1/4″, G5, Control concepts
12	413-412	2	BOLT, Hex, 1/4″-20 x 3/4″, G5, Full Thd, Control concepts
13	231-5144	5	NUT, Flg, USR, 1/4″-20, Control concepts
2	1301687C1	1	RETAINER, RETAINER spring, control concepts
3	1301728C1	1	SPRING, valve, control concepts
4	1301686C1	1	CAP, PLUG hex, special, end, control concepts
5	237-6010	2	O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk, Control concepts
6	1301631C1	1	SCREW, PLUG, valve body, seal, control concepts
7	107825	1	NUT, Stamped, 1/2″-20, hex, 1/2 in. NF, control concepts
8	1301632C1	1	CAP, COVER coil, control concepts
9	1301730C1	1	VALVE, COIL control concepts
10	1301648C1	1	ARMATURE, valve, control concepts
11	238-6019	1	O-RING, -019, 90 Duro, .801″ ID x .070″ Thk, Control concepts
12	1301624C1	1	BUSHING, poppet, pole, control concepts
13	1301627C1	1	STUD, SLEEVE poppet, valve, control concepts
14	1301642C1	1	WASHER, spring, retaining, control concepts
15	1301729C1	1	SPRING, poppet, control concepts
16	1301647C1	1	POPPET, POPPET, control concepts
17	1301625C1	1	ORIFICE, valve, control concepts
18	238-6010	1	O-RING, -010, 90 Duro, .239″ ID x .070″ Thk, Control concepts
19	1301649C1	1	SCREW, PLUG orifice, control concepts
20	86625138	1	PLUG, Hex Soc, 7/8″-14 ORB, Control Concepts, Includes Ref. 21
21	529909R1	1	O-RING, 7/64 ID x 1/4 in. wide, control concepts
32	187851C1	1	BODY, valve, modular control
33	187849C1	1	VALVE, SOLENOID, solenoid, 4 way, cartridge only, modular control
3	108641C1	1	GLAND, cylinder, front, feeder clutch cylinder
6	108639C1	1	ROD, PISTON, cylinder, feeder clutch cylinder
7	232-41110	1	NUT, LOCK, 5/8″-11, GC, Feeder clutch cylinder
11	108640C2	1	PISTON, cylinder, feeder clutch cylinder
23	108641C1	1	GLAND, cylinder, front, separator clutch cylinder
26	108639C1	1	ROD, PISTON, cylinder, separator clutch cylinder
27	232-41110	1	NUT, LOCK, 5/8″-11, GC, Separator clutch cylinder
31	108640C2	1	PISTON, cylinder, separator clutch cylinder
2	1341920C1	1	PROTECTOR, GUARD valve, gas, accumulator assembly 1978111C1
3	276-14912	2	SCREW, SELF TAPPING, Hex Hd, 3/8″ x 3/4″, self tapping, hex head, 3/8 NC x 3/4 in., accumulator
5	1978143C1	1	PISTON, CORE valve, accumulator assembly 1978111C1
6	1978144C1	1	CAP, valve, accumulator assembly 1078111C1
7	1978158C1	1	O-RING, O RING sealing, valve, accumulator assembly 1978111C1
8	1341919C1	1	KIT, GASKET, seal, accumulator, valve, not shown, accumulator assembly 1978111C1
2	1341920C1	1	PROTECTOR, GUARD valve, gas, accumulator assembly 128191A1
3	276-14912	2	SCREW, SELF TAPPING, Hex Hd, 3/8″ x 3/4″, WIRE retaining, feeder clutch cylinder, accumulator
5	1978143C1	1	PISTON, CORE valve, accumulator assembly 128191A1
6	1978144C1	1	CAP, valve, accumulator assembly 128191A1
7	1978158C1	1	O-RING, O-RING valve, sealing, accumulator assembly 128191A1
8	1341919C1	1	KIT, GASKET, seal, accumulator, valve, not shown, accumulator assembly 128191A1
9	S301363	1	GLAND, accumulator assembly 128191A1
10	S301364	1	PISTON, accumulator assembly 128191A1
11	S301365	2	RING, wear, teflon, piston, accumulator assembly 128191A1
12	414-812	3	BOLT, Hex, 1/2″-20 x 3/4″, G5, Full Thd, BOLT hex, 1/2 NF x 3/4 in., mounting and system
13	80679	3	WASHER, LOCK, 1/2″, Mounting and system
14	495-81025	3	WASHER, 17/32″ x 1 1/4″ x .179″, flat, 17/32 x 1-1/4 x 5/32 in., mounting and system
15	1979278C2	1	SUPPORT, accumulator, mounting and system
16	409-7516	2	BOLT, Hex Flg, 5/16″-18 x 1″, Serr, Mounting and system
17	231-5145	2	NUT, Flg, USR, 5/16″-18, Mounting and system
18	214-1480	1	CLAMP, HOSE, #80, 4.62/5.50 Type F Worm, Adj., Mounting and system
19	201-102	2	CONNECTOR, HYD., 13/16″-16 ORFS x 3/4″-16 ORB, Mounting and system, Includes Ref. 20 and 21
20	237-6008	1	O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk, Mounting and system
21	238-6014	1	O-RING, -014, 90 Duro, .489″ ID x .070″ Thk, Mounting and system
22	201-349	1	ELBOW, 90є, 13/16″-16 Adj x 13/16″-16 Fem Sw, ORFS, 90 deg., 13/16-16 swivel face seal x 3/4-16
23	237-6008	1	O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk, Mounting and system
24	183510C1	1	VALVE, needle, mounting and system
25	1989665C1	1	HOSE, accumulator, 32 in. (815 mm) long, mounting and system
26	201-412	1	TEE, 13/16″-16 x 3/4″-16 Run, ORFS, 13/16-16 face branch x face x 3/4-16 in. adj. O-ring, mounting
27	238-6014	2	O-RING, -014, 90 Duro, .489″ ID x .070″ Thk, Mounting and system
28	237-6008	1	O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk, Mounting and system
1	1282488C92	1	CYLINDER ASSY., unloader swing, 1-12 (38) ID x 20 in. (508 mm) stroke, see Fig. 8-76
2	218-5103	1	ELBOW, 90є, 7/16″-20, 37є x 7/16″-20, O-Ring, 90 deg., 7/16-20 in. flare x adj. O-ring boss, Includes:
3	237-6004	1	O-RING, 4-1, 90 Duro, .351″ ID x .072″ Thk
4	218-5053	1	CONNECTOR, HYD., 7/16″-20, 37є x 7/16″-20, O-Ring, ADAPTER, Incl. Ref. 5
5	237-6004	1	O-RING, 4-1, 90 Duro, .351″ ID x .072″ Thk
6	1317623C1	1	PIPE, TUBE, unloader swing cylinder
7	66880C1	4	HOSE ASSY., unloader swing, 20 in. (508 mm) long
8	218-671	2	FITTING, Blkhd, 7/16″-20, 37є x 7/16″-20, 37є, ADAPTER straight, 7/16-20 in. flare x bulkhead flare
9	218-1252	2	NUT, LOCK, Blkhd, 7/16″-20, hex, lock, bulkhead, 7/16 in. NF
10	196751C1	2	PIPE, TUBE, unloader swing cylinder
11	218-5320	2	ELBOW, 90є, 7/16″-20, 37є x 3/4″-16, O-Ring, 90 deg., 7/16-20 flare x 3/4-16 in. adj. O-ring boss
12	237-6008	1	O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
13	1267035C94	1	VALVE, ASSY., double piloted, unloader swing, see Fig. 8-42, no longer available, order 124857A1
13	124857A1	1	VALVE, ASSY., double piloted, unloader swing, see Fig. 8-43A, ASN JJC105314
14	183824C1	2	CLAMP, unloader swing tubes
15	413-416	2	BOLT, Hex, 1/4″-20 x 1″, G5
16	231-5144	2	NUT, Flg, USR, 1/4″-20
17	214-1432	1	CLAMP, HOSE, #32, 1.56/2.50 Type F Worm, Adjustable
18	163489C1	1	STRIP, INSULATOR rubber, 1/4 ID x 1-13/64 in. long
1	1282488C92	1	CYLINDER ASSY., hydraulic, swing, 1-1/2 (38) ID x 20 in. (508 mm) long, Includes: Ref. 2 thru 15
3	1252291C1	1	HEAD, GLAND cylinder. front
6	1285720C1	1	ROD, piston
9	1285719C1	1	PISTON, cylinder
12	9411658	1	NUT, LOCK, 5/8″-11, GC, hex, self locking, 5/8 in. NF, grade 8
14	9672438	1	PLUG, Hex Hd, 7/16″-20 ORB
17	28196R1	2	SPLIT PIN/SAFETY PIN, clevis, 5/8 x 2-1/4 in.
18	432-816	2	PIN, SPLIT (COTTER), 1/8″ x 1″
1	191529C91	1	LEVER ASSY., fan jackshaft drive, Includes: Ref. 2
2	556448R1	2	BUSHING, LEVER
3	495-11081	9	WASHER, 3/4″, SAE
4	219-87	1	NIPPLE, LUBE, 1/4″-28 x .56″ lg, Self-Tap
5	174520C2	1	ROD, jackshaft drive lever
6	425-108	2	NUT, 1/2″-13, G5
7	432-1216	1	PIN, SPLIT (COTTER), 3/16″ x 1″, 3/16″ x 1″
8	495-11053	3	WASHER, 1/2″, SAE, (17/32″ x 1-1/16″ x 3/32″)
9	495-81025	1	WASHER, 17/32″ x 1 1/4″ x .179″, flat, 17/32 x 1-1/4 x 5/32 in.
10	191777C1	1	SUPPORT, drive rod, fan jackshaft
13	231-5146	2	NUT, Flg, USR, 3/8″-16
14	477-73816	2	SCREW, Sltd Serr Truss Hd, 3/8″ x 1″, Special
15	194652C1	1	PIVOT, rod
16	155311C1	1	SPRING, rod
17	663887R91	1	PULLEY, drive, 8 in. O.D., fan jackshaft idler
18	425-1410	1	NUT, Jam, 5/8″-11, G5, hex, jam, 5/8 in. NC
19	413-1048	1	BOLT, Hex, 5/8″-11 x 3″, G5, hex, 5/8 NC x 3 in.
20	492-11062	1	WASHER, LOCK, 5/8″
21	495-11066	2	WASHER, 5/8″, SAE, flat, 21/32 x 1-5/16 x 3/32 in.
22	191305C1	1	V-BELT, drive, 112 in. over center, fan jackshaft
24	191603C2	1	PULLEY, drive, 12 in. O.D., feeder
25	183325C1	1	PULLEY, driven, 13 in. O.D., fan jackshaft
26	193948C1	1	PULLEY, drive, 9-3/4 in. O.D., cleaning unit
27	188298C2	1	STUD, PIN pivot, jackshaft drive lever
28	425-1012	2	NUT, 3/4″-10, G5
29	32-1620	1	PIN, SPLIT (COTTER), 1/4″ x 1 1/4″
30	492-11075	1	WASHER, LOCK, 3/4″, 3/4″
31	192011C1	1	SUPPORT, idler drive, fan jackshaft
32	231-5146	2	NUT, Flg, USR, 3/8″-16
33	477-73816	2	SCREW, Sltd Serr Truss Hd, 3/8″ x 1″, Special
1	193447C91	1	ARM, elevator jacjkshaft idler, Includes: Ref. 2
2	556448R1	2	BUSHING, lever, idler
4	191531C2	1	ROD, idler lever, elevator drive
5	425-108	2	NUT, 1/2″-13, G5
6	432-1216	1	PIN, SPLIT (COTTER), 3/16″ x 1″, 3/16″ x 1″
7	495-11053	5	WASHER, 1/2″, SAE, (17/32″ x 1-1/16″ x 3/32″)
8	495-81162	1	WASHER, 17/32″ x 1 1/2″ x .179″, flat, 17/32 x 1-1/2 x 11/64 in.
9	219-87	1	NIPPLE, LUBE, 1/4″-28 x .56″ lg, Self-Tap
10	1315483C1	1	BRACKET, SUPPORT, elevator drive rod
11	413-516	11	BOLT, Hex, 5/16″-18 x 1″, G5, Full Thd, hex, 5/16 NC x 1 in.
13	425-105	7	NUT, 5/16″-18, G5
14	492-11031	15	WASHER, LOCK, 5/16″
17	193948C1	1	PULLEY, drive, 9-3/4 in. O.D., cleaning unit, Includes: Ref. 18
18	47-49	16	RIVET, FH, 1/4″ x 9/16″, flat head solid, 1/4 x 9/16 in.
19	413-640	3	BOLT, Hex, 3/8″-16 x 2 1/2″, G5, hex, 3/8 NC x 2-1/2 in.
20	492-11038	7	WASHER, LOCK, 3/8″
23	181055C1	1	BELT, drive, 201 in. over center, cleaning unit, Combine with straw chopper
23	186509C2	1	BELT, drive, 255 in. over center, elevator drive, Combine with discharge beater
24	188253C2	1	SUPPORT, elevator drive, fixed idler
25	154273C1	4	BOLT, Hex Flg, 3/8″-16 x 1″, Serr, BOLT hex, self locking, special, 3/8 NC x 1 in.
26	231-5146	12	NUT, Flg, USR, 3/8″-16
27	673214R91	2	PULLEY, elevator drive and fixed idler, 7-5/16 in. (186 mm) O.D.
28	425-1010	3	NUT, 5/8″-11, G5
29	413-1040	1	BOLT, Hex, 5/8″-11 x 2 1/2″, G5, hex, 5/8 NC x 2-1/2 in.
30	495-11066	5	WASHER, 5/8″, SAE, flat, 21/32 x 1-5/16 x 3/32 in.
33	492-11062	2	WASHER, LOCK, 5/8″
34	195161C1	1	PULLEY, drive, 8-3/8 in. O.D., beater drive
35	193682C1	1	PULLEY, driven, 25 in. O.D., shaker shaft
36	495-11034	4	WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 in.
37	188298C2	1	STUD, PIN pivot, elevator jackshaft, idler driven
38	425-1012	2	NUT, 3/4″-10, G5
39	432-1620	1	PIN, SPLIT (COTTER), 1/4″ x 1 1/4″, 1/4″ x 1 1/4″
40	493-41078	1	WASHER, LOCK, Ext Tooth, 3/4″, external tooth lock, 3/4 in.
41	495-81137	3	WASHER, 13/32″ x 1″ x .224″, flat, 13/32 x 1 x 15/64 in.
43	183325C1	1	PULLEY, driven, 13 in. O.D., jackshaft, driven, Includes: Ref. 44
44	104235	24	RIVET, FH, 3/16″ x 1/2″
45	413-620	3	BOLT, Hex, 3/8″-16 x 1 1/4″, G5, Full Thd, hex, 3/8 NC x 1-1/4 in.
46	231-4116	3	NUT, LOCK, 3/8″-16, GB, hex, self locking, 3/8 in. NC
47	495-81129	6	WASHER, 13/32″ x 3/4″ x .120″, flat, 13/32 x 3/4 x 7/64 in.
48	186588C2	1	CHANNEL, pivot arm support
49	182676C2	2	SUPPORT, elevator pivot
50	409-7612	1	BOLT, Hex Flg, 3/8″-16 x 3/4″, Serr
53	477-73816	4	SCREW, Sltd Serr Truss Hd, 3/8″ x 1″, Special
54	425-146	1	NUT, Jam, 3/8″-16, G5, hex, jam, 3/8 in. NC
55	1302352C2	1	SUPPORT, GUIDE elevator belt, upper
56	179464C1	2	SCREW, Sltd Serr Truss Hd, 3/8″-16 x 1 1/4″, slotted truss head, special, 3/8 NC x 1-1/4 in.
57	1302068C2	1	GUIDE, elevator belt, lower
58	495-81138	3	WASHER, 13/32″ x 1″ x .179″, flat, 13/32 x 1 x 11/64 in.
59	1302350C1	1	SHIELD, elevator fixed idler, Combine without straw chopper
60	413-612	4	BOLT, Hex, 3/8″-16 x 3/4″, G5, Full Thd, hex, 3/8 NC x 3/4 in.
63	425-106	4	NUT, 3/8″-16, G5
64	495-11041	4	WASHER, 3/8″, SAE, Flat, (13/32 x 13/16 x 1/16″)
65	413-1048	1	BOLT, Hex, 5/8″-11 x 3″, G5, hex, 5/8 NC x 3 in.
66	425-1410	1	NUT, Jam, 5/8″-11, G5, hex, jam, 5/8 in. NC
67	1302353C1	1	GUARD, SHIELD, elevator fixed idler, Combine with straw chopper
68	1302351C1	1	DEFLECTOR, elevator rear shield, Combine with straw chopper
69	477-73108	2	SCREW, Sltd Serr Truss Hd, 5/16″-18 x 1/2″, slotted truss head, 5/16 NC x 1/2 in.
70	231-5145	2	NUT, Flg, USR, 5/16″-18
71	564737R1	1	SPACER, 7/8″ Tube x 2 1/16″, 21/32 x 7/8 x 2-1/16 in., Combine with straw chopper
72	194652C1	1	PIVOT, rod, arm
73	155311C1	1	SPRING, arm rod
74	413-1048	1	BOLT, Hex, 5/8″-11 x 3″, G5, hex, 5/8 NC x 3 in.
75	95-81018	1	WASHER, 21/32″ x 2 1/2″ x .120″, flat, 21/32 x 2-1/2 x 7/64 in.
1	193923C4	1	BELT, rotor variable drive, see Fig. 9B-6
2	1330054C1	1	PULLEY, rotor drive variable, 17-1/2 in. O.D., Includes: Ref. 3
3	194665C1	3	BUSHING, pulley
4	219-86	1	NIPPLE, LUBE, 1/8″ x .62″ lg, Drive, grease, self tap, 1/8 PT x 5/8 in.
5	238-5226	2	O-RING, -226, 70 Duro, 1.984″ ID x .139″ Thk
7	194654C91	2	BEARING, jackshaft thrust
8	194394C1	1	HUB, FITTING, variable pulley, female
9	188309C2	1	SUPPORT, variable pulley, limit switch
10	231-5146	2	NUT, Flg, USR, 3/8″-16
12	477-73816	2	SCREW, Sltd Serr Truss Hd, 3/8″ x 1″, Special
13	413-12152	1	BOLT, Hex, 3/4″-10 x 9 1/2″, G5, BOLT hex, 3/4 NC x 9-1/2 in.
15	329-1412	1	NUT, Jam, 3/4″-10, G8
16	194464C2	1	SPROCKET, variable pulley, male, 25 teeth
17	191542C2	1	COUPLING, SPLINED, universal joint
19	191595C91	1	JOINT ASSY., universal drive, Includes: Ref. 20 thru 26
20	1300502C1	1	KIT, bearing, journal
21	1300501C1	2	U-BOLT, retaining, universal joint
22	425-116	4	NUT, 3/8″-24, G5, Hex
23	492-11038	4	WASHER, LOCK, 3/8″
30	426-720	4	BOLT, Hex, 7/16″-14 x 1 1/4″, G8, BOLT hex, 7/16 NC x 1-1/4 in. grade 8
31	492-11044	4	WASHER, LOCK, 7/16″
32	188848C1	1	PULLEY, rotor drive, stationary, 17-1/2 in. O.D.
33	188846C1	1	HUB, ASSY., rotor drive pulley, Includes: Ref. 34
34	191544C2	3	PIN, pulley
35	326-828	6	BOLT, Hex, 1/2″-13 x 1 3/4″, G8
36	392-21050	6	WASHER, LOCK, 1/2″, 1/2″
37	329-108	6	NUT, 1/2″-13, G8
1	181333C1	1	SUPPORT ASSY., jackshaft
2	409-7816	2	BOLT, Hex Flg, 1/2″-13 x 1″, Serr, BOLT hex serrated flange, 1/2 NC x 1 in.
3	425-108	7	NUT, 1/2″-13, G5
4	80679	19	WASHER, LOCK, 1/2″
5	413-820	8	BOLT, Hex, 1/2″-13 x 1 1/4″, G5, Full Thd, hex, 1/2 NC x 1-1/4 in.
6	181165C1	1	SUPPORT ASSY., jackshaft, left hand, separator
7	413-816	8	BOLT, Hex, 1/2″-13 x 1″, G5, Full Thd
8	181166C1	1	SUPPORT, jackshaft, right hand, separator
9	495-81162	1	WASHER, 17/32″ x 1 1/2″ x .179″, flat, 17/32 x 1-1/2 x 11/64 in.
10	181167C1	1	SUPPORT, jackshaft, upper, separator
11	231-5148	6	NUT, Flg, USR, 1/2″-13
12	360-820	1	BOLT, Hex Flg, 1/2″-13 x 1 1/4″, G8, Full Thd, BOLT hex flange, 1/2 NC x 1-1/4 in., grade 8
13	434-820	5	BOLT, CARRIAGE, Short NK, 1/2″-13 x 1 1/4″, G5, Full Thd, BOLT carriage, 1/2 NC x 1-1/4 in.
14	495-81287	9	WASHER, 17/32″ x 1 1/4″ x .120″, flat, 17/32 x 1-1/4 x 7/64 in.
15	181164C1	1	SUPPORT, separator jackshaft
16	181172C1	1	SUPPORT, jackshaft support, rear
17	181171C1	1	ROD, cross, support
18	425-1110	2	NUT, 5/8″-18, G5
19	495-81017	2	WASHER, 17/32″ x 3/4″ x .120″, flat, 17/32 x 3/4 x 1/8 in.
20	434-824	2	BOLT, CARRIAGE, Short NK, 1/2″-13 x 1 1/2″, G5, Full Thd, 1/2 NC x 1-1/2 in.
22	194901C1	1	ROD, belt support, separator clutch
23	434-612	2	BOLT, CARRIAGE, Short NK, 3/8″-16 x 3/4″, G5, Full Thd, 3/8 NC x 3/4 in.
25	1345342C1	2	BAND, PLATE, jackshaft shield
1	1308774C1	1	GUARD ASSY., SHIELD, drive pulley
2	231-5146	7	NUT, Flg, USR, 3/8″-16
3	477-73816	3	SCREW, Sltd Serr Truss Hd, 3/8″ x 1″, Special
4	492-11038	2	WASHER, LOCK, 3/8″
5	495-61041	2	WASHER, 3/8″ x 1″ x .063″
6	413-616	2	BOLT, Hex, 3/8″-16 x 1″, G5, Full Thd, hex, 3/8 NC x 1 in.
7	425-106	2	NUT, 3/8″-16, G5
8	185395C92	1	PROTECTION PLATE, ASSY., driven pulley, Includes: Ref. 9
10	477-73812	6	SCREW, Sltd Serr Truss Hd, 3/8″ x 3/4″, slotted truss head, special, 38/ NC x 3/4 in.
13	181168C1	1	SUPPORT, BRACKET shield, outer, belt drive
14	434-820	5	BOLT, CARRIAGE, Short NK, 1/2″-13 x 1 1/4″, G5, Full Thd, BOLT carriage, 1/2 NC x 1-1/4 in.
15	80679	5	WASHER, LOCK, 1/2″
16	425-108	5	NUT, 1/2″-13, G5
17	181169C1	1	SUPPORT ASSY., BRACKET, drive belt guide
18	432-1216	1	PIN, SPLIT (COTTER), 3/16″ x 1″, 3/16″ x 1″
19	495-11053	1	WASHER, 1/2″, SAE, (17/32″ x 1-1/16″ x 3/32″)
20	188440C1	1	HOSE, separator channel, 4-1/2 in. (115 mm) long, cut from 526602R1 bulk hose, see below
23	191961C2	1	SUPPORT, drive belt
25	193686C1	1	ANGLE, drive belt support, channel
1	195457C92	1	LEVER, ASSY., drive belt clutch
2	1302308C1	2	BUSHING, drive belt clutch lever, 1 ID x 1-1/4 O.D. x 1-1/8 in. wide, Includes: Ref. 2 and 3
3	1315229C2	1	PIN, pivot, separator clutch arm
4	432-1216	1	PIN, SPLIT (COTTER), 3/16″ x 1″, 3/16″ x 1″
5	495-81176	2	WASHER, 21/32″ x 1″ x .060″, flat, 21/32 x 1 x 3/64 in.
6	195459C1	1	PIN, LARGE, lever, drive belt clutch
7	432-1224	2	PIN, SPLIT (COTTER), 3/16″ x 1 1/2″
8	495-81073	7	WASHER, 1 1/32″ x 1 3/4″ x .060″, flat, 1-1/32 x 1-3/4 x 1/16 in.
9	174757C1	1	PULLEY, idler, 8 in. O.D., separator belt idler
10	559205R91	1	BEARING, drive belt idler pulley
13	193284C1	1	ROD, belt guide, cluth pulley belt guide
14	413-612	2	BOLT, Hex, 3/8″-16 x 3/4″, G5, Full Thd, hex, 3/8 NC x 3/4 in.
15	492-11038	2	WASHER, LOCK, 3/8″
16	194220C1	2	BAR, cylinder anchor
17	231-5146	6	NUT, Flg, USR, 3/8″-16
18	409-7620	6	BOLT, Hex Flg, 3/8″-16 x 1 1/4″, Serr
19	196676C1	1	SPACER, cylinder anchor bar
20	425-106	1	NUT, 3/8″-16, G5
21	492-11038	1	WASHER, LOCK, 3/8″
23	413-656	1	BOLT, Hex, 3/8″-16 x 3 1/2″, G5, hex, 3/8 NC x 3-1/2 in.
24	186747C3	1	PIVOT, separator drive arm, replaces 186747C2
25	195432C1	1	TUBE, BUSHING, cylinder extension
26	432-612	1	PIN, SPLIT (COTTER), 3/32″ x 3/4″
27	427-6178	1	PIN, CLEVIS, 3/8″ x 1.781″, Hardened
29	1303058C1	1	ROD, separator drive tightener
30	425-1010	3	NUT, 5/8″-11, G5
33	495-81029	3	WASHER, 21/32″ x 2″ x .120″, flat, 21/32 x 2 x 7/64 in.
34	186748C1	1	BRACKET, drive tightener rod
35	186744C1	1	TUBE, SLEEVE, tightener rod, inner
36	186745C1	1	SPRING, belt tightener, rod
37	186746C1	1	TUBE, HOUSING belt tightener, outer
38	191461C1	1	PULLEY, drive, 11 in. O.D., separator drive
39	191241C3	1	BELT, drive, 130 in. over center, separator, replaces 191441C2
43	186749C1	1	BRACKET, BRACKET tightener rod, separator rod
44	38-11612	1	PIN, LOCK, 1/4″ x 3/4″, Slotted, 1/4″ x 3/4″, Slotted
45	1979908C1	2	CLIP, rocking wrench
46	135270	2	BOLT, Slotted Tr Hd, 5/16″-18 x 3/4″, slotted truss head, 5/16 NC x 3/4 in.
47	231-5145	2	NUT, Flg, USR, 5/16″-18
48	1979527C1	1	WRENCH-HOOK, rocking
49	179464C1	2	SCREW, Sltd Serr Truss Hd, 3/8″-16 x 1 1/4″, slotted truss head, special, 3/8 Nc x 1-1/4 in.
50	231-5146	2	NUT, Flg, USR, 3/8″-16
51	1979526C2	1	HANDLE, SUPPORT, wrench handle, rocking
52	1979751C2	1	BAR, rotor rocker
1	181369C1	1	HOUSING, BLOCK bearing
2	219-1	1	NIPPLE, LUBE, 1/8″-27 x .66 lg
3	61991R91	1	BREATHER, 1/8″-27 NPT, Short, w/washer, FITTING, housing breather, 1/8 in. PT
4	191452C2	1	PULLEY, driven, 14-3/4 in. O.D.
5	189419C1	1	HUB, rear bearing
7	378691R1	2	RING, retaining
8	61802C91	2	BEARING, CONE, tapered roller, 1-15/32 in. ID, jackshaft
9	61801C1	2	BEARING, CUP, tapered roller, 2-31/64 in. O.D., jackshaft
10	188931C1	1	SEAL, hub, front
11	384386R91	1	SEAL, hub, rear
12	1957657C2	1	SHAFT, drive
13	191518C2	1	SPACER, jackshaft, rear
14	188930C1	1	RING, SPACER, front
16	160191C2	1	WASHER, flat, special, 1-12/ x 2 x 3/16 in.
17	433-828	6	BOLT, CARRIAGE, Short NK, 1/2″-13 x 1 3/4″, G5, 1/2 NC x 1-3/4 in.
18	396-41053	6	WASHER, 17/32″ x 1 1/4″ x .188″, HDN, flat, hardened, 17/32 x 1-1/4 x 3/16 in.
19	80679	6	WASHER, LOCK, 1/2″
20	425-108	6	NUT, 1/2″-13, G5
21	426-516	4	BOLT, Hex, 5/16″-18 x 1″, G8, Full Thd, BOLT hex, 5/16 NC x 1 in., grade 8
22	492-11031	4	WASHER, LOCK, 5/16″
23	496-21106	2	WASHER, 1 1/16″ x 2″ x .209″, flat, hardened, 1-1/16 x 2 x 13/64 in.
24	232-41316	2	NUT, LOCK, 1″-8, GC
1	191388C1	1	CASE, HOUSING gear
2	188126	1	PIPE, Nipple, 3/8″ NPT x 2″, PIPE drain
3	144164	1	O-RING, drain pipe
4	195429C1	1	TUBE, oil gauge
5	237-6016	1	O-RING, 16-1, 90 Duro, 1.171″ ID x .118″ Thk
6	195319C91	1	GAUGE ASSY., oil, Includes: Ref. 7
7	238-5210	2	O-RING, -210, 70 Duro, .734″ ID x .139″ Thk
10	188589C91	1	HOSE, bank lube, 22 in., 559 mm, long
11	F53473	1	NUT, special
12	1315597C1	1	GEAR SET, drive, 18 and 31 teeth
13	197609R91	3	BEARING, CONE, tapered roller, 1-3/8 in. ID
14	197608R1	3	BEARING, CUP, CONE tapered, roller bearing, 3 in. O.D., inner
16	938294R91	1	SEAL, oil, input shaft, inner
17	238-5250	1	O-RING, -250, 70 Duro, 4.984″ ID x .139″ Thk
18	191245C2	1	HUB, bell, rear
19	618023R91	1	BEARING, CONE, tapered roller, 1-3/8 in. ID
20	618024R1	1	BEARING, CUP, CONE tapered, roller, 2-1/2 in. O.D., outer
21	192527C1	1	SEAL, oil, input shaft, outer
22	191396C1	1	SHAFT, input
23	195428C1	2	NUT, input and output shaft
25	238-5259	1	O-RING, -259, 70 Duro, 6.234″ ID x .139″ Thk
26	191248C1	1	HUB, bell, right
27	935915R1	8	SHIM, bell housing, right, 0.015 in. thick
28	192528C1	1	SEAL, oil, output shaft
29	191384C1	1	SHAFT, output
30	191397C2	1	GASKET, cover
31	191249C1	1	COVER, gear housing
32	219-434	1	BREATHER, 1/8″-27 NPT, Short, w/washer, VALVE vent, includes felt washer, 1/8 PT x 1 in.
33	80679	4	WASHER, LOCK, 1/2″
34	413-816	4	BOLT, Hex, 1/2″-13 x 1″, G5, Full Thd
35	492-11038	17	WASHER, LOCK, 3/8″
36	413-620	10	BOLT, Hex, 3/8″-16 x 1 1/4″, G5, Full Thd, hex, 3/8 NC x 1-1/4 in.
37	413-824	2	BOLT, Hex, 1/2″-13 x 1 1/2″, G5, Full Thd, hex, 1/2 NC x 1-1/2 in.
38	231-5148	2	NUT, Flg, USR, 1/2″-13
39	496-21094	2	WASHER, 15/16″ x 1 3/4″ x .179″, HDN
40	231-46114	1	NUT, LOCK, 7/8″-14, GB, hex, self locking, 7/8 in. NF
41	413-512	7	BOLT, Hex, 5/16″-18 x 3/4″, G5, Full Thd, hex, 3/8 NC x 3/4 in.
42	496-21094	1	WASHER, 15/16″ x 1 3/4″ x .179″, HDN
1	188043C2	1	SUPPORT, belt guard, lower
4	194380C2	1	GUIDE, belt
5	179464C1	1	SCREW, Sltd Serr Truss Hd, 3/8″-16 x 1 1/4″, slotted truss head, special, 3/8 NC x 1-1/4 in.
6	188045C2	1	SUPPORT ASSY., belt guard, rear
8	194357C2	1	CHANNEL, CLIP tightener, special
10	194356C1	1	TUBE, SPACER spring rod
11	186890C4	1	PIVOT, spring rod, replaces 186890C3
12	495-81225	1	WASHER, 1 17/32″ x 2 1/2″ x .060″, flat, 1-17/32 x 2-1/2 x 3/64 in.
14	194216C2	1	ROD, tightener, feeder drive
15	425-108	3	NUT, 1/2″-13, G5
16	495-81163	1	WASHER, 17/32″ x 1 1/2″ x .120″, flat, 17/32 x 1-1/2 x 7/64 in.
17	23304R1	1	PIN, CLEVIS, 3/8″ x 1 9/16″
18	432-612	1	PIN, SPLIT (COTTER), 3/32″ x 3/4″
20	432-1240	1	PIN, SPLIT (COTTER), 3/16″ x 2 1/2″
22	194369C2	1	SUPPORT, cylinder
23	413-816	2	BOLT, Hex, 1/2″-13 x 1″, G5, Full Thd
24	231-5148	2	NUT, Flg, USR, 1/2″-13
25	439-1652	1	PIN, HEADED, 3/8″ x 3 1/4″, 3/8 x 3-1/4 in., grade 2
26	432-812	1	PIN, SPLIT (COTTER), 1/8″ x 3/4″
28	194383C3	1	BRACKET, support, upper
29	161945C1	2	SCREW, Sltd Serr Truss Hd, 5/16″-18 x 1″, slotted truss head, 5/16 NC x 1 in.
30	231-5145	2	NUT, Flg, USR, 5/16″-18
33	195109C1	1	ROD ASSY., BRACKET belt trap rod
34	477-73816	2	SCREW, Sltd Serr Truss Hd, 3/8″ x 1″, Special
36	174757C1	1	PULLEY, idler, 8 in. O.D.
37	559205R91	1	BEARING, PULLEY
38	1302308C1	2	BUSHING, LEVER, 1 ID x 1-1/4 O.D. x 1-1/8 in. wide
39	219-36	1	NIPPLE, LUBE, 45є, 1/8″ NPT x 7/8″ lg
40	432-1624	1	PIN, SPLIT (COTTER), 1/4″ x 1 1/2″
41	495-81069	6	WASHER, 1 1/32″ x 1 1/2″ x .060″, flat, 1-1/32 x 1-1/2 x 1/16 in.
42	1321886C1	1	COVER, belt, upper
43	495-11041	1	WASHER, 3/8″, SAE, Flat, (13/32 x 13/16 x 1/16″)
45	185414C2	1	SUPPORT, pivot
46	477-73816	4	SCREW, Sltd Serr Truss Hd, 3/8″ x 1″, Special
47	192111C1	1	ROD, retainer
48	432-1216	3	PIN, SPLIT (COTTER), 3/16″ x 1″, 3/16″ x 1″
50	194358C1	1	GUIDE, belt retainer, without rock trap
50	1989323C2	1	SUPPORT, GUIDE belt retainer, with rock trap
51	432-1216	1	PIN, SPLIT (COTTER), 3/16″ x 1″, 3/16″ x 1″
52	192131C3	1	SUPPORT, belt guard
53	194364C2	1	HINGE, pivot
54	409-7620	1	BOLT, Hex Flg, 3/8″-16 x 1 1/4″, Serr
58	192738C1	1	V-BELT, drive, feeder, 150-1/4 in., without rock trap
58	1315168C1	1	V-BELT, drive feeder, 166-1/2 in., with rock trap
59	1305297C1	1	PULLEY, driven, feeder, 22-9/16 in. O.D.
60	188315C1	1	DOOR, access, belt drive cover
61	937059R1	1	SCREW, Sltd Serr Truss Hd, 1/4″-20 x 1/2″, slotted truss head, 1/4 NC x 1/2 in.
62	413-48	1	BOLT, Hex, 1/4″-20 x 1/2″, G5, Full Thd, hex, 1/4 NC x 1/2 in.
63	231-1444	1	NUT, LOCK, 1/4″-20, GB
65	126177	1	DISC, wing, door, 1/4 in. NC
66	186189C93	1	GUARD, SHIELD belt, includes decal, Includes: Decal
69	100-11150	1	RING, SNAP, #150, Ext, Spring rod
70	194521C1	1	SUPPORT, gear case
71	477-73812	4	SCREW, Sltd Serr Truss Hd, 3/8″ x 3/4″, slotted truss head, special, 3/8 NC x 3/4 in.
72	477-73816	2	SCREW, Sltd Serr Truss Hd, 3/8″ x 1″, Special
73	231-5146	6	NUT, Flg, USR, 3/8″-16
74	495-51053	4	WASHER, 1/2″, flat, 17/32 x 1 x 1/16 in.
75	191497C1	1	STRIP, SEAL support, 10-5/8 in., 270 mm, long
76	1319406C1	2	SCREW, CrossSerr Truss Hd, 3/8″-16 x 1″, trus head Phillips, self locking, special, 3/8 NC x 1 in..
77	191399C1	1	SUPPORT, gear housing, rear
78	477-73812	5	SCREW, Sltd Serr Truss Hd, 3/8″ x 3/4″, slotted trus head, special, 3/8 NC x 3/4 in.
79	231-5146	7	NUT, Flg, USR, 3/8″-16
80	191496C1	1	STRIP, SEAL, 11-7/8 in., 300 mm, long
83	186081C1	1	ANGLE, shield, upper
84	477-73108	2	SCREW, Sltd Serr Truss Hd, 5/16″-18 x 1/2″, slotted truss head, 5/16 NC x 1/2 in.
85	231-5145	2	NUT, Flg, USR, 5/16″-18
87	186080C2	1	SUPPORT, shield, upper
88	191603C2	1	PULLEY, drive, 12 in. O.D.
90	1315085C1	1	GUARD, SHIELD belt, extension, with rock trap
95	1315075C1	1	ANGLE, SUPPORT shield, rear extension
96	1315083C1	1	SUPPORT, shield, lower extension, with rock trap
97	1989332C3	1	SUPPORT, belt guide, upper, with rock trap, replaced by 1989332C4 and 198332C5
98	413-628	1	BOLT, Hex, 3/8″-16 x 1 3/4″, G5
100	477-73816	2	SCREW, Sltd Serr Truss Hd, 3/8″ x 1″, Special
101	49139D	1	WASHER, flat, 13/32 x 1-1/4 x 31/64 in.
102	1989328C1	1	COVER, drive belt, upper
1	663562R1	2	FLANGE, bearing, left hand, round design
2	1307583C1	2	FLANGE, bearing, left hand, square design
3	434-816	4	BOLT, CARRIAGE, Short NK, 1/2″-13 x 1″, G5, Full Thd, carriage, 1/2 NC x 1 in.
4	231-5148	4	NUT, Flg, USR, 1/2″-13
5	455112R11	1	COLLAR, locking, bearing
6	455111R91	1	BEARING, BALL, ball, jackshaft, left hand
7	1319482C2	1	SHAFT, cross, jackshaft
8	1321645C1	1	PULLEY, driven, feeder, 13-1/2 in. O.D.
9	Q1376	1	KEY, square tapered, 3/8 x 2-1/4 in.
10	1313095C2	1	V-BELT, drive, 47 in. feeder
10	1313097C3	1	BELT, drive, 146 in. over center
11	182322C1	1	SUPPORT, pivot, idler
12	434-612	2	BOLT, CARRIAGE, Short NK, 3/8″-16 x 3/4″, G5, Full Thd, 3/8 NC x 3/4 in.
13	231-5146	2	NUT, Flg, USR, 3/8″-16
15	413-472	2	BOLT, Hex, 1/4″-20 x 4 1/2″, G5, BOLT hex, 1/4 NC x 4-1/2 in.
16	231-4144	2	NUT, LOCK, 1/4″-20, GB
17	219-90	1	NIPPLE, LUBE, 45є, 1/4″ NPT x .80″ lg, Drive, grease, 45 deg., 1/4-28 special taper x 13/16 in.
18	1321982C1	1	ARM, tightener
19	176581C1	1	SPACER, spring, adjusting bolt
20	495-71053	2	WASHER, 1/2″, flat, 17/32 x 1-3/4 x 3/32 in.
23	197410C1	1	BOLT, idler draw
24	425-108	1	NUT, 1/2″-13, G5
25	182323C1	1	SUPPORT, idler
28	434-612	2	BOLT, CARRIAGE, Short NK, 3/8″-16 x 3/4″, G5, Full Thd, 3/8 NC x 3/4 in.
29	231-5146	2	NUT, Flg, USR, 3/8″-16
32	1345410C1	1	BUSHING, pulley, 17 x 35 x 15 mm
33	135260A1	1	SCREW, BOLT hex, special, 5/8 NC x 5 in.
33	413-1096	1	BOLT, Hex, 5/8″-11 x 6″, G5, hex, 5/8 NC x 6 in., if used
34	425-1010	1	NUT, 5/8″-11, G5, If used
34	232-41110	1	NUT, LOCK, 5/8″-11, GC
35	492-11062	1	WASHER, LOCK, 5/8″
40	176579C1	1	PULLEY, drive tightener, 8 in. O.D.
41	1305220C91	1	HUB ASSY., clutch outer, Includes: Ref. 42
42	610435C1	1	BUSHING, hub
43	1305393C1	1	SPACER, feeder pivot shaft, left hand, 2-35/64 in. long
44	1305154C2	1	HUB, slip clutch
45	181579C1	2	LINING, DISC friction, clutch
46	185955C1	1	PLATE, friction
47	584608R1	1	SPACER, clutch, 3-3/8 in. long
49	1305375C1	4	SPACER, drive lug
50	Q3959	2	KEY, Gib, 3/8″ Sq x 4 1/2″
51	1305692C2	8	SPRING, slip clutch, 10 with rock trap
52	1345355C1	1	GUARD ASSY., SHIELD support, front
53	256873	2	BOLT, Hex Flg, 5/16″-18 x 1/2″, Serr
54	231-5145	4	NUT, Flg, USR, 5/16″-18
55	135270	2	BOLT, Slotted Tr Hd, 5/16″-18 x 3/4″, slotted truss head, 5/16 NC x 3/4 in.
56	480523R1	1	SPLIT PIN/SAFETY PIN, hair
57	1345358C1	1	GUARD, SHIELD, jackshaft, end
58	1345199C1	2	SUPPORT, HINGE shield, feeder jackshaft
59	477-73812	4	SCREW, Sltd Serr Truss Hd, 3/8″ x 3/4″, slotted truss head, special, 3/8 NC x 3/4 in.
60	231-5146	4	NUT, Flg, USR, 3/8″-16
61	619333R1	2	FLANGE, bearing, right hand
62	434-816	4	BOLT, CARRIAGE, Short NK, 1/2″-13 x 1″, G5, Full Thd, carriage, 1/2 NC x 1 in.
63	231-5148	4	NUT, Flg, USR, 1/2″-13
65	664598R11	1	COLLAR, lock, bearing
66	664597R91	1	BEARING, ball jackshaft, right hand
67	1305297C1	1	PULLEY, driven, 22-9/16 in. O.D.
68	1305288C1	1	PULLEY, drive, feeder, 16-11/16 in. O.D.
69	326-656	4	BOLT, Hex, 3/8″-16 x 3 1/2″, G8
70	492-11038	4	WASHER, LOCK, 3/8″
71	329-106	4	NUT, 3/8″-16, G8
72	M74461	1	SPACER, 1″ Pipe x 3/4″, Support pin
74	1315319C1	8	BOLT, hex, special, 3/8 x 6 in., grade 8
75	231-4116	8	NUT, LOCK, 3/8″-16, GB, hex, self locking, 3/8 in. NC
77	495-81143	16	WASHER, 13/32″ x 1 1/2″ x .120″, flat, 13/32 x 1-1/2 x 7/64 in.
78	1320160C3	1	SHAFT, conveyor, feeder, see Fig. 9A-34 for cotter pins
79	1305370C3	8	SPACER, spring clutch
80	495-81129	8	WASHER, 13/32″ x 3/4″ x .120″, flat, 13/32 x 3/4 x 7/64 in.
81	495-81093	5	WASHER, 1 25/32″ x 2 1/2″ x .120″, flat, 1-25/32 x 2-1/2 x 7/64 in., not shown
82	1315316C1	2	SUPPORT, spring, slip clutch, with rock trap
83	1345357C1	1	GUARD, SHIELD jackshaft end, left hand
85	1321841C1	1	GUARD, SHIELD jackshaft drive, 47 in. feeder
85	1321966C1	1	SUPPORT, SHIELD jackshaft drive, 54-1/2 in. feeder
86	480523R1	4	SPLIT PIN/SAFETY PIN, hair
87	1327779C1	1	SUPPORT, shield, upper rear
88	1321851C1	1	SUPPORT, shield, lower rear
89	434-612	3	BOLT, CARRIAGE, Short NK, 3/8″-16 x 3/4″, G5, Full Thd, 3/8 NC x 3/4 in.
90	231-5146	3	NUT, Flg, USR, 3/8″-16
92	1321853C1	1	SUPPORT, SHIELD lower front
93	256873	2	BOLT, Hex Flg, 5/16″-18 x 1/2″, Serr
94	231-5145	2	NUT, Flg, USR, 5/16″-18
101	194652C1	1	PIVOT, rod
105	485-13116	2	SET SCREW, Sq Hd, 5/16″-18 x 1″, set, square head, cup point, 5/16 NC x 1 in.
106	425-105	2	NUT, 5/16″-18, G5
107	1957636C1	1	HOLDER, BRACKET shield, retainer
1	120871A2	1	HOUSING, feeder, includes decal, 47 in. feeder, replaces 120871A1
1	120873A2	1	HOUSING, feeder, includes decal, 54-1/2 in. feeder, repalces 120873A1, Includes: Ref. 1A
2	1324576C1	1	PLATE, lower support, 47 in. feeder
2	185820C1	1	SHEET, PLATE lower support, perforated, 47 in. feeder
2	1324578C1	1	PLATE, lower support, 54-1/2 in. feeder
2	1313970C1	1	PANEL, PLATE lower support, perforated, 54-1/2 in. feeder
3	415-820	4	BOLT, CARRIAGE, Short NK, 1/2″-13 x 1 1/4″, G8, Full Thd, BOLT carriage, 1/2 NC x 1-1/4 in., grade 8
5	433-1028	6	BOLT, CARRIAGE, Short NK, 5/8″-11 x 1 3/4″, G5, 5/8 NC x 1-3/4 in.
6	186852C1	8	NUT, hex, self locking, special, 1/2 in. NC, grade 8
8	496-81008	6	WASHER, 1 1/16″ x 1 7/8″ x .134″, HDN, sqare hole, 21/32 x 1-1/4 x 1/16 in.
9	231-14110	6	NUT, LOCK, 5/8″-11, GB, hex, self locking, 5/8 in. NC
12	1989330C2	1	SHIELD, ADAPTER feeder
13	1338021C1	2	PIN, retaining
14	231-1435	2	NUT, LOCK, 5/16″-18, GB, Hex, self locking
15	495-11034	4	WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 in.
16	367833R1	2	SPRING, rod, latch
17	177138C1	2	ROD, latch
18	179024C1	2	HINGE, HANDLE lock, latch
19	18518R1	2	PIN, LOCK, 1/8″ x 1″, Slotted
20	495-81175	4	WASHER, 21/32″ x 1″ x .120″, flat, 21/32 x 1 x 7/64 in.
21	138-2005	2	PIN, 1/4″ x 1″, Coiled
22	177141C1	2	PIN, pivot, handle
25	1321735C2	2	BOLT, EYE adjusting
26	329-108	4	NUT, 1/2″-13, G8
27	439-5836	2	PIN, HEADED, 1/2″ x 2 1/4″, headed, 1/2 x 2-1/4 in.
28	495-11053	2	WASHER, 1/2″, SAE, (17/32″ x 1-1/16″ x 3/32″)
29	432-1216	2	PIN, SPLIT (COTTER), 3/16″ x 1″, 3/16″ x 1″
30	231-5145	10	NUT, Flg, USR, 5/16″-18
32	1327737C2	2	PLATE, COVER feeder, side
33	95-81018	2	WASHER, 21/32″ x 2 1/2″ x .120″, flat, 21/32 x 2-1/2 x 7/64 in.
35	184853C1	1	DEFLECTOR, front, left hand
36	184854C1	1	DEFLECTOR, front, right hand
37	135270	10	BOLT, Slotted Tr Hd, 5/16″-18 x 3/4″, slotted truss head, 5/16 NC x 3/4 in.
40	1319474C1	1	BAND, COVER feeder, top
41	1319479C1	1	COVER, feeder, adapter
42	409-7516	12	BOLT, Hex Flg, 5/16″-18 x 1″, Serr
43	495-21038	5	WASHER, 5/16″, flat, 3/8 x 7/8 x 3/32 in.
43	495-81001	7	WASHER, 5/16″, flat, 3/8 x 1-1/8 x 1/16 in.
44	232-4115	5	NUT, LOCK, 5/16″-18, GC
44	231-5345	7	NUT, LOCK, Flg, 5/16″-18, hex flange, self locking, 5/16 in. NC
45	1321640C1	2	GROMMET, cover, adapter
46	1327752C1	1	SEAL, side, left hand
47	1327753C1	1	SEAL, side, right hand
48	109253A1	1	PLATE, LARGE, STRIP feeder cover
49	1957434C1	1	SUPPORT, jackshaft bearing, left hand
50	434-816	2	BOLT, CARRIAGE, Short NK, 1/2″-13 x 1″, G5, Full Thd, carriage, 1/2 NC x 1 in.
51	231-5148	2	NUT, Flg, USR, 1/2″-13
2	477-73816	16	SCREW, Sltd Serr Truss Hd, 3/8″ x 1″, Special
4	434-820	4	BOLT, CARRIAGE, Short NK, 1/2″-13 x 1 1/4″, G5, Full Thd, BOLT carriage, 1/2 NC x 1-1/4 in.
5	635503R1	2	SPRING, latch, lower door
6	167570C1	2	CHAIN, latch, lower door
8	495-11053	2	WASHER, 1/2″, SAE, (17/32″ x 1-1/16″ x 3/32″)
9	80679	4	WASHER, LOCK, 1/2″
10	425-108	4	NUT, 1/2″-13, G5
11	1345329C1	1	SUPPORT, feeder housing, reinforcement
15	1541620C1	1	SUPPORT ASSY., BRACKET lift support, includes decal, 47 in. feeder
15	1541619C1	1	SUPPORT ASSY., BRACKET lift support, includes decal, 54-1/2 feeder
16	197554C3	1	CHANNEL, lift cylinder, lock
17	586591R1	1	PIN, SPLIT (COTTER), hair, 1/8 in.
18	439-1652	1	PIN, HEADED, 3/8″ x 3 1/4″, 3/8 x 3-1/4 in., grade 2
19	186852C1	16	NUT, hex, self locking, special, 1/2 in. NC, grade 8
20	197849C1	1	ROD, cylinder lift, lock
21	432-812	2	PIN, SPLIT (COTTER), 1/8″ x 3/4″
23	495-11034	1	WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 in.
24	231-5146	16	NUT, Flg, USR, 3/8″-16
25	1327992C2	1	GUARD, SHIELD sensor, feeder
26	256873	2	BOLT, Hex Flg, 5/16″-18 x 1/2″, Serr
27	488837C1	2	NUT, speed, 5/16 in. NC
28	415-820	16	BOLT, CARRIAGE, Short NK, 1/2″-13 x 1 1/4″, G8, Full Thd, BOLT carriage, 1/2 NC x 1-1/4 in., grade 8
29	187101C2	1	SUPPORT, BRACKET auxiliary lift cylinder, welded to assembly
2	193362C2	1	DOOR, lower, bottom feeder
3	1319963C1	1	STRIP, SEAL, feeder bottom support, rear
4	1319961C1	1	SUPPORT, feeder, bottom, rear
5	1319965C1	1	BAR, spacer, support
6	197429C1	1	STRIP, SEAL door, strip
7	443-11012	6	SCREW, Cross Flat Hd, #10-24 x 3/4″, machine, flat Phillips, No. 10 NC x 3/4 in.
8	196922C1	6	NUT, hex, self locking, No. 10
9	193364C2	1	HINGE, door, feed plate
10	477-73812	6	SCREW, Sltd Serr Truss Hd, 3/8″ x 3/4″, slotted truss head, special, 3/8 NC x 3/4 in.
11	231-5146	6	NUT, Flg, USR, 3/8″-16
12	159012C1	1	ROD, hinge, door
15	197426C4	1	COVER, feeder, upper
16	434-816	2	BOLT, CARRIAGE, Short NK, 1/2″-13 x 1″, G5, Full Thd, 1/2 NC x 1 in.
17	186852C1	2	NUT, hex, self locking, special, 1/2 in. NC, grade 8
18	411-636	1	BOLT, CARRIAGE, Short NK, 3/8″-16 x 2 1/4″, G2, BOLT carriage, 3/8 NC x 2-1/4 in., grade 2
19	413-48	52	BOLT, Hex, 1/4″-20 x 1/2″, G5, Full Thd, hex, 1/4 NC x 1/2 in.
20	1322144C1	2	ANGLE, door stop
21	231-5144	2	NUT, Flg, USR, 1/4″-20
22	154273C1	4	BOLT, Hex Flg, 3/8″-16 x 1″, Serr, BOLT hex, self locking, special, 3/8 NC x 1 in.
23	231-5146	4	NUT, Flg, USR, 3/8″-16
24	634204R1	1	SEAL, fedder, top
25	180555C91	1	DOOR ASSY., feeder, upper, top
26	197418C1	1	SUPPORT, ANGLE seal support
27	175906C1	1	ROD, hinge, door
28	1321431C1	1	PROTECTION PLATE, PANEL hinged, feeder top, 47 in. feeder
29	415-824	8	BOLT, CARRIAGE, Short NK, 1/2″-13 x 1 1/2″, G8, BOLT carriage, 1/2 NC x 1-1/2 in., grade 8
30	195-81030	8	WASHER, flat, 17/32 x 1-1/2 x 3/16 in.
31	186852C1	8	NUT, hex, self locking, special, 1/2 in. NC, grade 8
32	1321395C1	1	BOLT, adjusting, level
33	396-31081	4	WASHER, 13/16″ x 1 1/2″ x .219″, HDN
34	425-1012	3	NUT, 3/4″-10, G5
35	184645C1	1	CLIP, latch, door
36	7422T	1	SPRING, latch, door
37	495-11041	1	WASHER, 3/8″, SAE, Flat, (13/32 x 13/16 x 1/16″)
38	425-106	2	NUT, 3/8″-16, G5
39	1321638C1	1	COVER, upper, front
40	425-148	8	NUT, Jam, 1/2″-13, G5
1	117865A1	1	CHAIN (AGRICULTURE), ASSY., conveyor, with 9 serrated slats, 54-1/2 in. feeder, rice, A557
1	117869A1	1	CHAIN (AGRICULTURE), ASSY., conveyor, with 10 smooth slats, 47 in. feeder, corn and grain, A557
1	117864A1	1	CHAIN (AGRICULTURE), ASSY., conveyor, with 10 serrated slats, 47 in. feeder, corn and grain, A557
1	117871A1	1	CHAIN (AGRICULTURE), ASSY., conveyor, with 12 smooth slats, 54-1/2 in. feeder
3	189709C1	2	BOLT, hex, special
4	425-108	2	NUT, 1/2″-13, G5
5	80679	2	WASHER, LOCK, 1/2″
6	495-81162	2	WASHER, 17/32″ x 1 1/2″ x .179″, flat, 17/32 x 1-1/2 x 11/64 in.
8	197211C1	2	SPACER, stop, drum
9	176508C1	2	BOLT, tightening, special
10	425-1010	4	NUT, 5/8″-11, G5
11	187218C1	2	BOLT, hex, special, 5/8 NC x 4-1/2 in.
12	425-1010	4	NUT, 5/8″-11, G5
15	396-21066	2	WASHER, 21/32″ x 1 5/16″ x .150″, HDN, flat, hardened, 21/32 x 1-5/16 x 5/32 in.
16	1330461C1	4	FLANGE, bearing, drum
17	1306680C1	12	NUT, LOCK, hex flange, self locking, special, 3/8 in. NC
18	557995R11	2	COLLAR, bearing, locking, with set screw
20	619738R91	2	BEARING, ball, drum, conveyor
22	1957437C1	1	DRUM, conveyor, without stone retarder
23	187207C2	1	ROD, SHAFT drum, feeder
24	1338287C3	2	ARM, drum, left hand, replaces 1338291C2
25	1338288C3	2	ARM, drum, right hand, replaces 1338292C2
26	1319875C5	1	ARM, drum, left hand, replaced 1319875C5
26	1319875C5	1	ARM, drum, left hand, replaces 1319875C4
27	1319876C4	1	ARM, drum, right hand, replaced by 1319876C5
27	1319876C5	1	ARM, drum, right hand, replaces 1319876C4
31	179665C91	2	BEARING, BALL, ball, shaft
33	178780C2	1	SPACER, sprocket, left hand
34	178781C2	1	SPACER, sprocket, right hand
35	1970248C1	2	SPROCKET ASSY., chain, conveyor
37	197643C1	4	SCREW, set, sprocket
38	1320160C3	1	SHAFT, conveyor
39	432-2040	2	PIN, SPLIT (COTTER), 5/16″ x 2 1/2″, 5/16″ x 2 1/2″
44	185818C1	1	STRIPPER ASSY., pivot, left hand
45	185819C1	1	STRIPPER ASSY., pivot, right hand
46	477-73812	4	SCREW, Sltd Serr Truss Hd, 3/8″ x 3/4″, slotted truss head, special, 3/8 NC x 3/4 in.
47	231-5146	4	NUT, Flg, USR, 3/8″-16
48	187347C1	2	PLATE, BAR adjusting, upper stop
50	1345418C1	2	ANGLE, stop bar, upper
51	433-1036	2	BOLT, CARRIAGE, Short NK, 5/8″-11 x 2 1/4″, G5, 5/8 NC x 2-1/4 in.
52	425-1010	2	NUT, 5/8″-11, G5
53	492-11062	2	WASHER, LOCK, 5/8″
54	498-81008	2	WASHER, 41/64″ x 1 1/4″ x .060″, Sq Hole, square hole, 21/32 x 1-1/4 x 1/16 in.
55	187225C1	2	BAR, adjusting, upper stop, with stone retarder
57	187217C1	2	SPACER, 7/8″ Tube x 1 13/16″
60	1957439C3	1	DRUM, conveyor, with stone retarder
70	326-656	2	BOLT, Hex, 3/8″-16 x 3 1/2″, G8
71	314148R1	2	SPACER, 3/8″ X-Strng Pipe x .469″, Pivot arm
72	231-1446	2	NUT, LOCK, 3/8″-16, GB
73	112046A2	4	STRIP, PROTECTION, filler
1	1327628C3	1	HOUSING, rock trap
2	409-7516	6	BOLT, Hex Flg, 5/16″-18 x 1″, Serr
3	231-5145	27	NUT, Flg, USR, 5/16″-18
4	1320279C1	1	ANGLE, wear, rock trap
5	135270	12	BOLT, Slotted Tr Hd, 5/16″-18 x 3/4″, slotted truss head, 5/16 NC x 3/4 in.
6	495-81135	6	WASHER, 13/32″ x 1″ x .120″, flat, 13/32 x 1 x 7/64 in.
7	179665C91	2	BEARING, BALL, ball, beater
8	1327925C4	1	COVER ASSY, housing, rock trap, beater
9	409-7612	4	BOLT, Hex Flg, 3/8″-16 x 3/4″, Serr
10	1320254C1	2	PLATE, backup seal
12	195202C1	2	SEAL, feeder
13	231-5146	11	NUT, Flg, USR, 3/8″-16
14	154273C1	7	BOLT, Hex Flg, 3/8″-16 x 1″, Serr, BOLT hex, self locking, special, 3/8 NC x 1 in.
15	326-16128	2	BOLT, Hex, 1″-8 x 8″, G8, Replaces 326-16104
16	232-41316	2	NUT, LOCK, 1″-8, GC
17	495-11106	4	WASHER, 1″, SAE, flat, 1-1/16 x 2 x 1/8 in., replaces 396-31106
19	1320154C1	1	HINGE, door, rock trap
20	1320149C1	1	ROD, door hinge
21	1324880C1	1	ANGLE, door
22	1319834C1	1	BEATER, feed, trap
23	1324438C1	3	KNIFE, EXTENSION blade, beater
23	1320921C2	3	BLADE, beater, serrated
24	434-624	15	BOLT, CARRIAGE, Short NK, 3/8″-16 x 1 1/2″, G5, 3/8 NC x 1-1/2 in.
25	425-106	15	NUT, 3/8″-16, G5
26	492-11038	15	WASHER, LOCK, 3/8″
27	1327502C1	1	SHAFT, beater drive
28	477-73812	5	SCREW, Sltd Serr Truss Hd, 3/8″ x 3/4″, slotted truss head, 3/8 NC x 3/4 in.
29	231-5146	5	NUT, Flg, USR, 3/8″-16
30	432-2040	2	PIN, SPLIT (COTTER), 5/16″ x 2 1/2″, 5/16″ x 2 1/2″
35	1320268C1	1	SPACER, sprocket, left hand
36	1320269C1	1	SPACER, sprocket, right hand
37	162172C1	1	SPACER, 1-13/16 x 2-1/4 x 1-15/16 in.
40	1320151C1	1	ROD, door latch
41	432-1216	2	PIN, SPLIT (COTTER), 3/16″ x 1″, 3/16″ x 1″
42	188915A1	1	HANDLE, door, left hand, replaces 1324752C1
43	413-816	2	BOLT, Hex, 1/2″-13 x 1″, G5, Full Thd
44	231-4118	2	NUT, LOCK, 1/2″-13, GB, hex, self locking, 1/2 in. NC
46	1324742C1	1	SUPPORT, latch stop
47	174608C2	3	BOLT, hex, special, 3/8 NC x 1-1/2 in.
48	425-106	3	NUT, 3/8″-16, G5
49	1320128C1	2	LINK, connecting
50	413-616	2	BOLT, Hex, 3/8″-16 x 1″, G5, Full Thd, hex, 3/8 NC x 1 in.
51	232-4136	2	NUT, LOCK, 3/8″-16, GC
52	1320846C1	1	SUPPORT ASSY., ANGLE
66	1957362C1	1	SUPPORT, latch stop
67	1324775C1	1	SUPPORT, latch, center
68	413-616	2	BOLT, Hex, 3/8″-16 x 1″, G5, Full Thd, hex, 3/8 NC x 1 in.
69	232-4136	2	NUT, LOCK, 3/8″-16, GC
1	245927C91	1	MOTOR, STARTER, ASSY., feeder reverser, See Fig. 4-46
2	413-636	3	BOLT, Hex, 3/8″-16 x 2 1/4″, G5
3	231-5146	3	NUT, Flg, USR, 3/8″-16
4	1321534C1	1	SHAFT, reverser
5	409-7816	1	BOLT, Hex Flg, 1/2″-13 x 1″, Serr, BOLT hex, serrated flange, 1/2 NC x 1 in.
6	495-91167	2	WASHER, 17/32″ x 2″ x .120″, flat, 17/32 x 2 x 7/64 in.
8	1329717C1	1	SPROCKET, drive, 20 teeth
10	1321537C91	1	FLYWHEEL, motor, reverser
12	1321539C1	1	HOUSING, shaft, reverser
13	187620C1	2	BOLT, Hex Flg, 3/8″-16 x 1 1/2″, Serr, BOLT hex flange, special, 3/8 NC x 1-1/2 in.
15	219-87	3	NIPPLE, LUBE, 1/4″-28 x .56″ lg, Self-Tap
17	100-21315	2	RING, SNAP, 3.156″, Int, #315
18	597537R91	2	BEARING, BALL, ball
19	1321523C1	1	SPACER, bearing
20	896-16036	1	WASHER, M39 x 78.5 x 7, HT, flat, hardened, 39 x 78 x 7 mm
21	38-33248	1	PIN, 1/2″ x 3″, Coiled, 1/2″ x 3″, Coiled
22	1321780C2	1	SUPPORT, shield
24	1321710C1	1	SUPPORT, shield
28	120867A1	1	GUARD, SHIELD feeder reverser, includes decal
29	480523R1	4	SPLIT PIN/SAFETY PIN, hair
33	1329840C1	1	BRACKET, support, rear
34	1329838C2	1	BRACKET, support, front
35	1329720C2	1	SPROCKET, driven, 40 teeth
36	1329719C2	1	SPROCKET, beater driven, rock trap, 20 teeth, if used
36	1320110C3	1	SPROCKET, beater driven, rock trap, 32 teeth, if used
36	125407A1	1	SPROCKET, beater driven, rock trap, 30 teeth, replaces 1320110C3
37	541857R92	1	SPROCKET, idler, 15 teeth
38	413-1072	1	BOLT, Hex, 5/8″-11 x 4 1/2″, G5
41	396-31066	1	WASHER, 21/32″ x 1 5/16″ x .188″, HDN, flat, 21/32 x 1-5/16 x 3/16 in.
44	1321528C2	1	SUPPORT, idler, outer
45	1321933C3	1	SUPPORT, idler
47	413-1060	1	BOLT, Hex, 5/8″-11 x 3 3/4″, G5, BOLT hex, 5/8 NC x 3-3/4 in.
48	1330032C1	1	SPRING, return, idler
50	1321531C93	1	SPROCKET, idler, fixed, Includes: Ref. 51
51	630836C91	1	BEARING, NEEDLE, neddle, 1-19/64 in. O.D.
52	1327991C1	2	BUSHING, bearing, inner
53	1327990C1	1	BOLT, Hex, 3/4″-10 x 4, Drilled, Idler
54	425-1012	1	NUT, 3/4″-10, G5
55	492-11075	1	WASHER, LOCK, 3/4″, 3/4″
56	396-31081	2	WASHER, 13/16″ x 1 1/2″ x .219″, HDN
57	1321529C95	1	CHAIN, 88-1/2 in. long, 118 links, see below 111714A1 and 111716A1
58	187217C1	1	SPACER, 7/8″ Tube x 1 13/16″
60	413-628	2	BOLT, Hex, 3/8″-16 x 1 3/4″, G5
1	245927C91	1	MOTOR, STARTER, ASSY., feeder reverser, see Figure 4-46
2	413-636	3	BOLT, Hex, 3/8″-16 x 2 1/4″, G5
3	231-5146	3	NUT, Flg, USR, 3/8″-16
4	1321534C1	1	SHAFT, reverser
5	409-7816	1	BOLT, Hex Flg, 1/2″-13 x 1″, Serr, BOLT hex serrated flange, 1/2 NC x 1 in.
6	495-91167	2	WASHER, 17/32″ x 2″ x .120″, flat, 17/32 x 2 x 7/64 in.
8	1329717C1	1	SPROCKET, drive, 20 teeth
10	1321537C91	1	FLYWHEEL, motor, reverser
12	1321539C1	1	HOUSING, shaft, reverser
13	187620C1	2	BOLT, Hex Flg, 3/8″-16 x 1 1/2″, Serr, BOLT hex flange, special, 3/8 NC x 1-1/2 in.
15	219-87	2	NIPPLE, LUBE, 1/4″-28 x .56″ lg, Self-Tap
17	100-21315	2	RING, SNAP, 3.156″, Int, #315
18	597537R91	2	BEARING, BALL, ball
19	1321523C1	1	SPACER, bearing
20	896-16036	1	WASHER, M39 x 78.5 x 7, HT, flat, hardened, 39 x 78 x 7 mm
21	38-33248	1	PIN, 1/2″ x 3″, Coiled, 1/2″ x 3″, Coiled
22	1979317C1	1	SUPPORT ASSY., shield
28	120866A1	1	GUARD, SHIELD feeder reverser, includes decal
29	480523R1	3	SPLIT PIN/SAFETY PIN, hair
33	1329840C1	1	BRACKET, support, rear
34	1329838C2	1	BRACKET, support, front
35	1979299C2	1	SUPPORT, idler bar
36	25253R1	1	BOLT, Hex, 3/8″-16 x 7″, G8, hex, 3/8 NC x 7 in., grade 8
37	495-81002	1	WASHER, 3/8″, flat, 7/16 x 1-3/8 x 5/64 in.
38	232-4136	1	NUT, LOCK, 3/8″-16, GC
39	1979303C1	1	SPACER, TUBE
40	1979305C1	1	ARM, SUPPORT idler
42	326-888	1	BOLT, Hex, 1/2″-13 x 5 1/2″, G8
44	232-4118	1	NUT, LOCK, 1/2″-13, GC
47	629972R91	1	DRIVE SPROCKET, idler, 15 teeth
48	413-1064	1	BOLT, Hex, 5/8″-11 x 4″, G5, hex, 5/8 NC x 4 in.
50	495-11066	4	WASHER, 5/8″, SAE, flat, 21/32 x 1-5/16 x 3/32 in.
51	396-31066	1	WASHER, 21/32″ x 1 5/16″ x .188″, HDN, flat, 21/32 x 1-5/16 x 3/16 in.
52	232-41110	1	NUT, LOCK, 5/8″-11, GC
55	1330032C1	1	SPRING, return, idler
58	1329720C2	1	SPROCKET, driven, 40 teeth
59	1321524C94	1	CHAIN, 57 in. long, 76 links, Part includes connecting link kit, O-rings, link plate, pin, lube pack and
60	UA17298	1	SPACER, 7/8″ Tube x 1 1/16″, 7/8 x 1-1/6 in.
61	1979304C1	1	SPACER, spring
62	154397C1	1	SPACER, 5/8″ Tube x 1 1/4″, tubular, 5/8 O.D. x 1-1/4 in. long
1	1312482C2	1	SUPPORT, height indicator
2	1312488C1	1	CAP, height indicator
3	326-512	2	BOLT, Hex, 5/16″-18 x 3/4″, G8, Full Thd
4	1312483C1	1	ANGLE, BRACKET height indicator
5	934666R1	4	SCREW, SELF TAPPING, Slotted Pan Hd, M4.8 x 9.5, self tapping, pan head, 10 x 10 mm
6	439-1428	1	PIN, HEADED, 1/4″ x 1 3/4″, G2, 1/4 x 1-3/4 in., grade 2
7	432-612	1	PIN, SPLIT (COTTER), 3/32″ x 3/4″
10	1312489C1	1	SPRING, tension, indicator
11	1312492C1	1	HOOK, indicator
12	932265R1	1	PIN, LOCK, M3 x 24, Slotted, 3 x 24 mm
13	3168318R2	1	CABLE, height indicator
14	715945R91	1	CLAMP, height cable
15	1312485C2	1	SUPPORT ASSY., indicator
16	495-81024	1	WASHER, 17/32″ x 1 1/4″ x .060″, flat, 17/32 x 1-1/4 x 1/16 in.
17	153528C1	1	PIN, hair type
1	1315340C4	1	HOUSING, ASSY., rotor drive, see Fig. 9B-10
2	181315C1	1	PLATE, support, gear housing, front
3	413-824	4	BOLT, Hex, 1/2″-13 x 1 1/2″, G5, Full Thd, hex, 1/2 NC x 1-1/2 in.
4	80679	4	WASHER, LOCK, 1/2″
5	181314C2	2	BLOCK, housing support, front
6	188141C1	1	SUPPORT, gear housing anchor
7	188142C1	1	SUPPORT, gear housing anchor
8	188143C1	1	EYEBOLT, EYE gear housing
9	413-1244	2	BOLT, Hex, 3/4″-10 x 2 3/4″, G5, hex, 3/4 NC x 2-3/4 in.
12	495-81030	2	WASHER, 21/32″ x 2″ x .179″, flat, 21/32 x 2 x 11/64 in.
13	425-1010	2	NUT, 5/8″-11, G5
14	432-1216	1	PIN, SPLIT (COTTER), 3/16″ x 1″, 3/16″ x 1″
15	439-5832	1	PIN, HEADED, 1/2″ x 2″, 1/2 x 2 in.
20	360-820	2	BOLT, Hex Flg, 1/2″-13 x 1 1/4″, G8, Full Thd, BOLT hex flange, 1/2 NC x 1-1/4 in., grade 8, replaces
20	434-820	4	BOLT, CARRIAGE, Short NK, 1/2″-13 x 1 1/4″, G5, Full Thd, BOLT carriage, 1/2 NC x 1-1/4 in.
22	231-5148	6	NUT, Flg, USR, 1/2″-13
23	413-616	4	BOLT, Hex, 3/8″-16 x 1″, G5, Full Thd, hex, 3/8 NC x 1 in.
24	492-11038	4	WASHER, LOCK, 3/8″
25	1338395C1	1	SUPPORT ASSY., rotor drive, gear housing
26	194066C91	1	DIPSTICK, GAUGE ASSY., rotor gear housing
27	238-5210	2	O-RING, -210, 70 Duro, .734″ ID x .139″ Thk
28	193946C1	1	TUBE, gear housing gauge
29	135270	2	BOLT, Slotted Tr Hd, 5/16″-18 x 3/4″, slotted truss head, 5/16 NC x 3/7 in.
30	231-5145	2	NUT, Flg, USR, 5/16″-18
31	214-1404	2	CLAMP, HOSE, #4, 0.25/0.62 Type M Worm, Adj, retaining
32	194043C1	1	HOSE, 19 in. (483 mm) long, cut from S118466X bulk hose, see below
33	194058C1	1	SUPPORT, gear housing, rear
34	413-828	4	BOLT, Hex, 1/2″-13 x 1 3/4″, G5
35	80679	4	WASHER, LOCK, 1/2″
38	194077C1	2	SPACER, gear housing
39	413-848	2	BOLT, Hex, 1/2″-13 x 3″, G5, hex, 1/2 NC x 3 in.
41	396-41053	4	WASHER, 17/32″ x 1 1/4″ x .188″, HDN, flat, hardened, 17/32 x 1-1/4 x 3/16 in.
42	1979327C1	1	SPACER, lever, rotor gear housing shift
45	100395A1	1	SUPPORT, gear housing pivot
46	413-512	2	BOLT, Hex, 5/16″-18 x 3/4″, G5, Full Thd, hex, 5/16 NC x 3/4 in.
47	492-11031	2	WASHER, LOCK, 5/16″
48	100398A1	1	LEVER ASSY., rotor drive shift
49	432-1216	2	PIN, SPLIT (COTTER), 3/16″ x 1″, 3/16″ x 1″
50	1979265C1	1	BUSHING, shift lever
51	495-11034	1	WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 in.
52	439-5521	1	PIN, HEADED, 5/16″ x 1 5/16″, headed, 5/16 x 1-5/16 in.
53	432-812	1	PIN, SPLIT (COTTER), 1/8″ x 3/4″
55	231-4116	1	NUT, LOCK, 3/8″-16, GB, hex, self locking, 3/8 in, NC
56	413-620	1	BOLT, Hex, 3/8″-16 x 1 1/4″, G5, Full Thd, hex, 3/8 NC x 1-1/4 in.
57	495-21044	1	WASHER, 3/8″, flat, 8/16 x 1 x 5/64 in.
61	188272C1	1	ELBOW, gear housing, 90 deg., special
62	237-6008	1	O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
71	186648C2	1	ROD, lever shaft control linkage
72	1979564C1	1	SUPPORT, shift lever
74	413-820	2	BOLT, Hex, 1/2″-13 x 1 1/4″, G5, Full Thd, hex, 1/2 NC x 1-1/4 in.
75	231-5148	2	NUT, Flg, USR, 1/2″-13
76	198825C1	1	GROMMET, control rod, 5/8 in. ID
77	163493C1	1	STRIP, SLEEVE oil hose cover, 3/4 (19) ID x 1-13/64 in. (46 mm) long
78	1315304C2	1	PLATE, torque spring, removal
79	1319996C2	2	ROD ASSY., BOLT torque sensing spring, special, 11-1/2 in. plate
80	429-106	2	NUT, 3/8″-16, G8, hex, 3/8 in. NC, grade 8
1	194058C1	1	SUPPORT, rear gear housing
2	413-828	4	BOLT, Hex, 1/2″-13 x 1 3/4″, G5
3	80679	4	WASHER, LOCK, 1/2″
4	194077C1	2	SPACER, gear housing
5	413-848	2	BOLT, Hex, 1/2″-13 x 3″, G5, hex, 1/2 NC x 3 in.
6	396-41053	2	WASHER, 17/32″ x 1 1/4″ x .188″, HDN, flat, hardened, 17/32 x 1-1/4 x 3/16 in.
7	1315340C4	1	HOUSING, ASSY., rotor drive, see Figure 9B-10
8	1315291C2	1	HUB, fixed variable pulley, welded
8	184489C1	1	HUB, fixed variable pulley, machined, forged
9	1315292C2	1	PULLEY, fixed variable
10	310-1824	12	BOLT, Locking, 1/2″-13 x 1 1/2″, G8, BOLT hex, self locking, 1/2 NC x 1-1/2 in., grade 8
11	193923C4	1	BELT, rotor variable drive, 85 in. over center
12	1315294C3	1	PULLEY, ASSY., adjustable variable
13	193965C91	3	SEAL, pulley , Part included in bushing and seal repair kit 188839C92
15	537602R1	1	RING, retaining, pulley
16	219-1	1	NIPPLE, LUBE, 1/8″-27 x .66 lg
17	1315521C1	1	STOP, WASHER thrust, rotor drive
18	184486C1	1	SPRING, 9-1/32 in., free length
20	193941C1	2	BUSHING, yoke pivot
21	1315344C2	1	HUB, cam follower, torque sensing
22	1315343C1	2	BEARING, cam follower
23	194167C1	2	SCREW, BOLT, cam follower, yoke pivot
24	425-1110	2	NUT, 5/8″-18, G5
25	1315297C2	1	HUB, CAM torque sensing, drive rotor
26	360171R1	1	RING, retaining, hub cam follower
27	370255R2	1	WASHER, flat, hardened, 57/64 x 1-7/8 x 7/32 in.
28	1315288C1	1	NUT, hex, self locking, special, 7/8 in. NC
30	1319996C2	2	ROD ASSY., BOLT torque sensing spring, special, 11-1/2 in.
1	126573C1	1	MOTOR, ELECTRIC, variable speed , BSN JJC0105560
1	111787A1	1	MOTOR, ELECTRIC, variable speed , ASN JJC0105560
2	413-412	3	BOLT, Hex, 1/4″-20 x 3/4″, G5, Full Thd, Used with 126573C1 motor
2	413-432	2	BOLT, Hex, 1/4″-20 x 2″, G5, Used with 111787A1 motor
3	495-81137	3	WASHER, 13/32″ x 1″ x .224″, flat, 13/32 x 1 x 15/64 in., used with 126573C1 motor
4	55825C1	1	BUSHING, electric motor
5	194338C1	1	GEAR, rotor gear
6	38-11020	1	PIN, LOCK, 5/32″ x 1 1/4″, Slotted, 5/32″ x 1 1/4″, Slotted
7	495-11066	8	WASHER, 5/8″, SAE, flat, 21/32 x 1-5/16 x 3/32 in.
8	Q5024	1	KEY, 3/16″ Sq x 1″, Par
9	55826C1	2	BUSHING, gear shaft
10	183227C1	2	SUPPORT ASSY., motor, with three motor mounting holes, used with 126573A1
10	183227C2	1	SUPPORT, motor, with five motor mounting holes, used with 111787A1
11	409-7616	8	BOLT, Hex Flg, 3/8″-16 x 1″, Serr
12	495-81135	8	WASHER, 13/32″ x 1″ x .120″, flat, 13/32 x 1 x 7/64 in., Includes: Ref. 13 thru 16
13	231-5146	8	NUT, Flg, USR, 3/8″-16
14	113485A1	2	SPACER, 17 mm, used with 111787A1 motor
15	425-104	2	NUT, 1/4″-20, G5, Used with 111787A1 motor
17	188203C3	1	SUPPORT, rotor adjusting, left hand
18	179464C1	2	SCREW, Sltd Serr Truss Hd, 3/8″-16 x 1 1/4″, slotted truss head, special, 3/8 NC x 1-1/4 in.
19	477-73812	2	SCREW, Sltd Serr Truss Hd, 3/8″ x 3/4″, slotted truss head, special, 3/8 NC x 3/4 in.
20	231-5146	6	NUT, Flg, USR, 3/8″-16
21	194336C2	1	SUPPORT, rotor adjusting, right hand
22	477-73816	2	SCREW, Sltd Serr Truss Hd, 3/8″ x 1″, Special
23	495-71041	2	WASHER, 3/8″, flat, 13/32 x 1-1/4 x 3/32 in.
24	231-5146	2	NUT, Flg, USR, 3/8″-16
25	194337C1	1	SPROCKET, control, 8 teeth
26	485-12512	2	SET SCREW, Sq Hd, 1/4″-20 x 3/4″, set, square head, cup point, 1/4 NC x 3/4 in.
27	425-144	2	NUT, Jam, 1/4″-20, G5
30	1302173C1	2	PAD, motor support
31	413-624	2	BOLT, Hex, 3/8″-16 x 1 1/2″, G5
32	495-11041	4	WASHER, 3/8″, SAE, Flat, (13/32 x 13/16 x 1/16″)
33	492-11038	2	WASHER, LOCK, 3/8″
34	425-106	2	NUT, 3/8″-16, G5
2	194064C91	1	HOUSING ASSY., rotor gear, Includes: Ref. 3
3	37-1820	2	DOWEL, 1/2″ x 1 1/4″, PIN, hardened, 1/2 x 1-1/4 in.
4	ST863	2	BEARING, CUP, tapered roller, housing
5	ST783A	2	BEARING, CONE, tapered roller, housing
6	1338222C1	1	BREATHER, 1/8″-27, Short, Housing
7	194047C1	1	BUSHING, input shaft
8	194051C1	2	SEAL, oil
9	13363D	2	BEARING SET, tapered roller, gear
10	13367DC	2	BEARING, CONE, tapered roller, gear
11	194057C1	2	WASHER, THRUST
14	193828C1	1	PINION, GEAR driven, 47 teeth
15	619085C91	4	BEARING, NEEDLE
16	193824C1	1	PINION, GEAR driven, 58 teeth
17	194059C1	1	SHAFT, rotor drive output
18	194069C1	1	COLLAR, shift
19	100400A1	1	FORK, SHIFTER
21	211-1014	1	BALL, 7/16″ Dia, chrome alloy steel, shifter rail, grade 24
22	107234C1	1	SPRING, compression
23	129998	1	PLUG, Hex Hd, 1/2″-20 ORB, Incl. Ref. 24
27	G10450	1	SEAL, oil, shift rail
28	194039C3	1	COVER, rotor gear housing
29	413-832	11	BOLT, Hex, 1/2″-13 x 2″, G5, hex, 1/2 NC x 2 in.
30	495-11053	1	WASHER, 1/2″, SAE, (17/32″ x 1-1/16″ x 3/32″)
32	1957654C1	1	SHAFT, input, rotor drive
33	370255R2	1	WASHER, flat, hardened, 57/64 x 1-7/8 x 7/32 in.
34	1315288C1	1	NUT, hex, self locking, special, 7/8 in. NC
24	237-6005	1	O-RING, 5-1, 90 Duro, .414″ ID x .072″ Thk
1	1302214C96	1	ROTOR, ASSY., threshing, Includes: Ref. 12 thru 35
2	191545C1	1	SHAFT, rotor, front
3	191546C2	1	IMPELLER, rotor, front
4	439-51272	1	PIN, HEADED, 3/4″ x 4 1/2″, G5
5	432-1620	1	PIN, SPLIT (COTTER), 1/4″ x 1 1/4″, 1/4″ x 1 1/4″
8	361-45024	9	SCREW, Hex Soc Flat Hd, 1/2″-13 x 1 1/2″, BOLT hex socket, 1/1 NC x 1-1/2 in., replaces 426-826
9	326-828	9	BOLT, Hex, 1/2″-13 x 1 3/4″, G8, Replaces 426-328
10	396-41053	39	WASHER, 17/32″ x 1 1/4″ x .188″, HDN, flat, hardened, 17/32 x 1-1/4 x 3/16 in.
11	199528A1	24	NUT, hex, self locking, 1/2 in. NC, grade 8, replaces 232-4118
12	326-844	3	BOLT, Hex, 1/2″-13 x 2 3/4″, G8
13	326-848	3	BOLT, Hex, 1/2″-13 x 3″, G8, Replaces 426-848
16	1308829C2	12	BAR, helical rasp
16	1324583C2	12	BAR, helical rasp support, chrome, This Ref. is not part of 1302214C96 rotor assembly and must be
17	426-620	24	BOLT, Hex, 3/8″-16 x 1 1/4″, G8, Full Thd, BOLT hex, 3/8 NC x 1-1/4 in., grade 8
18	396-21041	24	WASHER, 13/32″ x 13/16″ x .09″, HDN, flat, hardened, 13/32 x 13/16 x 3/32 in.
19	232-4136	24	NUT, LOCK, 3/8″-16, GC
20	1308668C1	9	RASP BAR, straight, rasp
20	1324582C1	9	BAR, straight, rasp, chrome, This Ref. is not part of 1302214C96 rotor assembly and must be
21	426-620	18	BOLT, Hex, 3/8″-16 x 1 1/4″, G8, Full Thd, BOLT hex, 3/8 NC x 1-1/4 in., grade 8
22	396-21041	18	WASHER, 13/32″ x 13/16″ x .09″, HDN, flat, hardened, 13/32 x 13/16 x 3/32 in.
23	232-4136	18	NUT, LOCK, 3/8″-16, GC
24	1303038C2	3	BAR, straight, rotor, rear
24	1324580C1	3	BAR, straight, rotor, rear, This Ref. is not part of 1302214C96 rotor assembly and must be purchased
25	409-7620	21	BOLT, Hex Flg, 3/8″-16 x 1 1/4″, Serr
26	231-5146	21	NUT, Flg, USR, 3/8″-16
30	1345307C1	1	COUPLING, rotor drive
32	326-848	6	BOLT, Hex, 1/2″-13 x 3″, G8, Replaces 426-848
33	80679	6	WASHER, LOCK, 1/2″
34	540468R1	12	WASHER, flat, hardened, special, 17/32 x 1-1/2 x 1/8 in.
35	183253C2	3	BAR, PLATE wear
35	1309185C1	3	SUPPORT, PLATE wear, chrome, This Ref. is not part of 1302214C96 rotor assembly and must be
41	424-1228	1	BOLT, Hex, 3/4″-10 x 1 3/4″, G2, BOLT hex, 3/4 NC x 1-3/4 in., grade 2
42	492-11075	1	WASHER, LOCK, 3/4″, 3/4″
45	183335C3	3	SUPPORT, BRACKET rotor extension

Pages: 1 2 3 4 5 6

Leave a Reply Cancel reply