7220 CASE IH Magnum Tractor (North America)

      No Comments on 7220 CASE IH Magnum Tractor (North America)

7220 CASE IH Magnum Tractor (North America) — parts list, part 1 of 5

3,640 part numbers across 1 assemblies, transcribed from the catalogue above and split over 5 pages. Search a page for a part number to find the assembly it belongs to; the page links are below the list.

Parts list

Pos Part no. Qty Description
1 A190663 1 RADIATOR, cooling system
2 A170241 1 CAP, RADIATOR, radiator, 15 psi
3 217-103 1 COCK, DRAIN, VALVE – 1/4 inch PT
4 252305A1 1 HOSE, LARGE, radiator, lower, replaces 1334477C1
5 1289072C1 1 HOSE, LARGE, radiator, upper
6 138773A1 4 CLAMP, coolant hose
9 1340707C1 1 SUPPORT ASSY., radiator
10 614-10030 5 BOLT, Hex, M10 x 30, 8.8
11 L46821 2 SHOCK ABSORBER, INSULATOR – rubber mount
12 48560 2 WASHER, flat, radiator support
13 1340708C1 1 PLATE, LARGE, radiator
14 131-1308 2 NUT, LOCK, Jam, 1/2″-13, hex, jam, self-locking, 1/2 inch NC
15 1955424C1 1 PLATE, bolster cover
17 1289320C1 1 DEFLECTOR, SHROUD – fan
22 217-151 1 FITTING, 3/8″ Hose X 1/4″ NPTF Beaded, Adapter – straight
23 1960764C1 1 HOSE, 560 mm (22 inch) long, radiator to engine
24 214-1406 2 CLAMP, HOSE, #06, .44/.78 Type F Worm
25 L18337 2 STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch, nylon
28 1289476C1 1 SEAL, hood to radiator, upper left
29 1968024C1 1 SEAL, radiator, lower support
30 1289473C1 3 SEAL, radiator, lower corners and between air duct and radiator
32 1348509C2 1 SEAL, radiator
33 1348510C2 1 SEAL, radiator
34 A171317 2 SEAL, fan shroud
35 J907208 1 TUBE, water inlet, Reference #s 35, 36, 37 are included in the engine assembly.
36 845-8016 1 BOLT, Hex Flg, M8 x 16, 8.8, Full Thd, , Reference #s 35, 36, 37 are included in the engine assembly.
37 J922847 1 CLAMP, tube retaining, Reference #s 35, 36, 37 are included in the engine assembly.
38 895-15010 5 WASHER, M11 x 24 x 2
1 140501A2 1 RADIATOR, ASSEMBLY – cooling system, emission control engines
2 243898A1 1 TANK, radiator, upper
3 243895A1 1 RESERVOIR, TANK – radiator, lower
4 243899A1 1 SUPPORT, radiator
5 614-8012 8 BOLT, Hex, M8 x 12, 8.8, Full Thd, Not shown
6 895-15008 8 WASHER, M8 x 20 x 1.6, Not shown
7 A170241 1 CAP, RADIATOR, radiator, 15 psi
8 217-103 1 COCK, DRAIN, VALVE-1/4 inch PT
9 186489A1 1 HOSE, LARGE, radiator, lower
10 198883A1 1 CLAMP, lower radiator hose, radiator side
11 138773A1 1 CLAMP, lower radiator hose, engine side
12 184299A1 1 HOSE, LARGE, radiator, upper
13 138773A1 2 CLAMP, upper radiator hose
14 217-151 1 FITTING, 3/8″ Hose X 1/4″ NPTF Beaded, Adapter – straight, Vent hose
15 1960764C1 1 HOSE, 560 mm (22 inch) long, radiator vent to engine
16 1348264C1 2 CLAMP, HOSE, 3/8 inch, radiator vent hose
17 L18337 1 STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch, vent hose to upper radiator hose
18 196816C1 1 FITTING, ADAPTER – barb stem, radiator, lower
19 237-6008 1 O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
20 3225216R2 1 HOSE, LARGE, 15 (5/8) ID x 460 mm (18-1/8 inch) long, cut from 97252CX bulk hose, high
21 1954736C1 2 CLAMP, HOSE, adjustable
22 1301342C1 1 FITTING, ADAPTER – straight, special
23 184111A2 1 SUPPORT, BRACKET – radiator, upper
24 187107A2 3 SEAL, adhesive back, 608 mm (23-15/16 inch) long, upper and lower fan shroud and upper radiator
25 844-8016 2 BOLT, Hex Flg, M8 x 16, 8.8, Upper bracket to radiator, outer mounting holes
26 614-6016 2 BOLT, Hex, M6 x 16, 8.8, Upper bracket inner mounting holes
27 495-81107 2 WASHER, .281″ x 7/8″ x .060″, flat, 9/32 x 7/8 x 3/64 inch
28 184112A2 1 SUPPORT, BRACKET – radiator, left-hand side
29 184113A2 1 SUPPORT, BRACKET – radiator, right-hand side
31 895-15008 4 WASHER, M8 x 20 x 1.6, If used
32 177080A1 2 SUPPORT, BRACKET – radiator support
33 60-6650T1 4 BUSHING, RUBBER, CUSHION – mount, radiator support bracket lower mounting holes
34 844-10030 4 BOLT, Hex Flg, M10 x 30, 8.8, Full Thd, BOLT – heavy hex flange, 10 – 1.5 x 30 mm, support bracket
35 495-81140 4 WASHER, 13/32″ x 1 1/4″ x .060″
36 234017A1 6 SCREW, BOLT – hex socket, 8 – 1.25 x 16 mm, upper mounting holes, replaces 844-8020 bolt
37 223350A2 1 PLATE, LARGE, radiator
38 227240A1 1 GASKET, rubber seal, tank replacement
39 864-10016 2 SCREW, Hex Soc Hd, M10 x 16, 8.8
40 141002A2 1 DEFLECTOR, SHROUD – fan, emission control engines
41 256990A1 1 SEAL, adhesive back, 764 mm (30-5/64 inch) long, radiator, lower frame between radiator and support
42 844-8016 10 BOLT, Hex Flg, M8 x 16, 8.8, Case installed, service with 614-8016, 892-11008 and 895-11008
43 185672A2 1 SEAL, trim, 3010 mm (118-1/2 inch) long, hood perimeter
44 177362A2 8 SEAL, trim, 55 mm (2-1 1/64 inch) long, hood, radiator frame and bolster plate
45 245983A1 2 SEAL ASSY., TRIM – edge, black, 28 mm (1-1/8 inch) long, order 1330108CX bulk seal and cut to
46 231604A1 1 CLIP, open type
47 J907208 1 TUBE, water inlet, Reference #s 35, 36, 37 are included in the engine assembly.
48 J922847 1 CLAMP, tube, Reference #s 35, 36, 37 are included in the engine assembly.
49 845-8016 1 BOLT, Hex Flg, M8 x 16, 8.8, Full Thd, , Reference #s 35, 36, 37 are included in the engine assembly.
1 A184979 1 FAN, engine, 6 blade, puller, 7210 Tractor
2 A184524 1 SPACER, fan, 7210 Tractor
3 814-10110 4 BOLT, Hex, M10 x 110, 8.8, 7210 Tractor
4 496-21041 4 WASHER, 13/32″ x 13/16″ x .089″, HDN, If used, 7210 Tractor
5 J911567 1 BELT, fan, V-ribbed, 1702 mm long, 7210 Tractor
6 A173447 1 FAN, engine, 7220 Tractor, prior to Tractor P.I.N. JJA0064978
7 A184523 1 SPACER, fan, 7220 Tractor, prior to Tractor P.I.N. JJA0064978
8 A173943 1 DRIVE ASSY., fan, 7220 Tractor, prior to Tractor P.I.N. JJA0064978
9 814-10080 4 BOLT, Hex, M10 x 80, 8.8, 7220 Tractor, prior to Tractor P.I.N. JJA0064978
10 496-21041 4 WASHER, 13/32″ x 13/16″ x .089″, HDN, 7220 Tractor, prior to Tractor P.I.N. JJA0064978
11 496-11034 6 WASHER, 11/32″ x 11/16″ x 1/16″, HDN, Replaces H426775 washer, 7220 Tractor, prior to Tractor
12 825-1408 6 NUT, M8, Cl 8, 7220 Tractor, prior to Tractor P.I.N. JJA0064978
13 J911567 1 BELT, fan, V-ribbed, 1702 mm long, 7220 Tractor, prior to Tractor P.I.N. JJA0064978
14 186431A1 1 FAN, engine, 8 blade, emission control engines, 7220 Tractor, Tractor P.I.N. JJA0064978 and after
15 187777A1 1 DRIVE ASSY., fan, 7220 Tractor, Tractor P.I.N. JJA0064978 and after
16 614-10030 4 BOLT, Hex, M10 x 30, 8.8, 7220 Tractor, Tractor P.I.N. JJA0064978 and after
17 892-11010 4 WASHER, LOCK, M10, 7220 Tractor, Tractor P.I.N. JJA0064978 and after
18 496-11034 6 WASHER, 11/32″ x 11/16″ x 1/16″, HDN, 220 Tractor, Tractor P.I.N. JJA0064978 and after
19 825-1408 6 NUT, M8, Cl 8, 7220 Tractor, Tractor P.I.N. JJA0064978 and after
20 J911567 1 BELT, fan, V-ribbed, 1702 mm long, 7220 Tractor, Tractor P.I.N. JJA0064978 and after
1 A190663 1 RADIATOR, cooling system
2 1289499C2 1 SUPPORT, BRACKET – reservoir mounting
3 614-10020 2 BOLT, Hex, M10 x 20, 8.8, Full Thd
4 892-11010 2 WASHER, LOCK, M10
7 A184395 1 RESERVOIR, BOTTLE – coolant recovery
8 1547924C1 1 CAP, recovery bottle, non-vented
9 281-34812 4 SCREW, SELF TAPPING, Hex Hd, 5/16″ x 3/4″, self-tapping, hex washer head, 5/16 NC x 3/4 inch
13 A172261 1 HOSE, LARGE, 1800 mm (70-7/8 inch) long, cut from L126767 bulk hose, coolant recovery
14 1340641C1 1 HOSE, LARGE, coolant recovery, 300 mm (11-13/16 inch) long, cut from L126767 bulk hose
15 A171099 3 CLAMP, HOSE, spring-type, hose retaining
16 516-22127 2 CLAMP, J, 9/16″ Insul, 5/16″ Bolt, harness, replaces R54362 clamp
1 140501A2 1 RADIATOR, ASSEMBLY – cooling system
2 A172261 1 HOSE, LARGE, 1800 mm (70-7/8 inch) long, cut from L126767 bulk hose, coolant bottle to radiator
3 142713A1 1 HOSE, LARGE, 1021 mm (40-7/32 inch) long, coolant recovery overflow
4 A171099 3 CLAMP, HOSE, spring-type, hose retaining
5 188891A1 1 RESERVOIR, coolant container
6 1547924C1 1 CAP, recovery bottle, non-vented
1 113077A1 1 AIR CLEANER, ASSEMBLY – includes precleaner, parts list Fig. 2-16
3 1289073C2 1 HOSE, LARGE, air cleaner to turbocharger
4 214-1476 2 CLAMP, HOSE, #76, 4.31/5.25 Type F Worm, W/liner, Adj.
5 1983640C1 1 SWITCH, SWITCH – restriction, air cleaner
6 113078A1 1 DUCT, air intake, with lower bracket, prior to tractor P I N JJA0064978
7 1975782C1 3 SCREW, SELF TAPPING, Cross Truss Wash Hd, #10 x 5/8″, Precleaner to air duct
8 614-8014 2 BOLT, Hex, M8 x 14, 8.8, Full Thd, BOLT – hex, full threads, 8 – 1.25 x 14 mm, if used
9 892-11008 2 WASHER, LOCK, M8, If used
10 895-11008 2 WASHER, M8 x 16 x 1.6, If used
11 1998851C1 1 HOSE, LARGE, 90 degree, aspirator
12 121746A1 1 PIPE, SUCTION, TUBE – aspirator
13 1998858C1 1 HOSE, LARGE, aspirator
14 214-1428 4 CLAMP, HOSE, #28, 1.31/2.25 Type F Worm, Adjustable
16 1334309C2 1 COLLAR CLAMP, aspirator tube, mounts to turbo shield
17 905-10025 1 BOLT, Hex Serr Flg, M10 x 25
18 829-2410 1 NUT, M10 x 1.5, Flg, Cl 10
19 814-10060 1 BOLT, Hex, M10 x 60, 8.8
20 895-11010 1 WASHER, M10 x 20 x 2
21 A176570 1 SPACER, clamp
22 829-2410 1 NUT, M10 x 1.5, Flg, Cl 10
23 1348516C3 1 SUPPORT, BRACKET – plate, air cleaner
24 905-10020 3 BOLT, Hex Serr Flg, M10 x 20
25 1348518C1 1 SUPPORT, BRACKET – air cleaner support, mounts to cylinder head
26 905-10025 2 BOLT, Hex Serr Flg, M10 x 25
27 829-2410 1 NUT, M10 x 1.5, Flg, Cl 10
28 1340702C1 1 SUPPORT, air cleaner
29 905-8012 1 BOLT, Hex Serr Flg, M8 x 12
30 1348517C1 1 SUPPORT, BRACKET – air cleaner mounting, mounts to cylinder head
31 905-10025 1 BOLT, Hex Serr Flg, M10 x 25
32 829-2410 1 NUT, M10 x 1.5, Flg, Cl 10
33 814-10060 1 BOLT, Hex, M10 x 60, 8.8
34 895-11010 1 WASHER, M10 x 20 x 2
35 A176570 1 SPACER, clamp
36 142742A1 1 DUCT, air intake, without lower bracket, tractor P.I.N. JJA0064978 and after
37 96900C1 3 NUT, U, #10-16, Panel type
3 A171256 1 FILTER, ELEMENT, secondary
4 A171255 1 FILTER, ELEMENT, primary
5 A47134 2 NUT, wing, retaining, element retaining
6 D37976 1 GASKET, air cleaner element
7 A184650 1 COVER ASSY, access
8 33-1387T1 1 NUT, WING, cover retaining
1 A143381 1 SOLENOID, ASSEMBLY – ether injection, no longer available, order 185552A2 ether start solenoid
2 D77648 1 BAIL, HANGER – ether can, no longer available, order 185552A2 solenoid assembly
3 395686R1 1 GASKET, injector solenoid, 15/64 inch diameter, if used
4 222-615 1 ELBOW, 90є, 5/16″-24 x 1/8″ NPT, Comp, 1/8 tube OD
5 222-650 1 SLEEVE, 1/8″ Tube, Comp, tapered, 1/8 inch tube OD
6 222-660 1 NUT, TUBE, 5/16″-24, 45є Fl, Comp, hex, 1/8 tube OD x 5/16-24 inch
9 413-512 4 BOLT, Hex, 5/16″-18 x 3/4″, G5, Full Thd, hex, 5/16 NC x 3/4 inch, if used
10 492-11031 4 WASHER, LOCK, 5/16″, If used
11 425-105 4 NUT, 5/16″-18, G5, If Used
14 1974410C1 1 TUBE, 1600 mm (63 inch) long, no longer available, order item 14A tube
15 L18337 3 STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch
16 A172900 1 NOZZLE CAP, ASSEMBLY – atomizer
17 217-40 1 REDUCER, 1/4″-18 NPTF x 1/8″-27 Fem NPTF, 1/4 PT x 1/8 inch female PT, brass
18 R30812 2 LINK, extension
19 1960785C2 1 SUPPORT, BRACKET – ether mounting, if used
20 185552A2 1 SOLENOID, ASSEMBLY – ether injection, continuous flow
21 190752A1 1 HOUSING, ether injection solenoid
22 614-8020 4 BOLT, Hex, M8 x 20, 8.8, If used
23 892-11008 4 WASHER, LOCK, M8, If used
24 825-1408 4 NUT, M8, Cl 8, If used
25 281-34812 2 SCREW, SELF TAPPING, Hex Hd, 5/16″ x 3/4″, self-tapping, hex washer head, 5/16 NC x 3/4 inch
1 1998855C2 1 ELBOW, exhaust casting
2 828-12055 4 BOLT, Hex, M12 x 55, 10.9
3 896-11012 4 WASHER, M13.5 x 24.5 x 3, HT
4 1998799C2 2 STUD, 12 x 150 mm
5 1998800C2 1 STUD, 12 x 60 mm
6 896-11012 3 WASHER, M13.5 x 24.5 x 3, HT
7 127594A1 3 NUT, hex, 12 mm – 1.75, special
8 1998778C2 1 GASKET, muffler, elbow to extension
9 1347836C3 1 MUFFLER, PIPE – exhaust, extension, replaces 1347836C2 pipe, if used
10 135162A1 1 PIPE ASSY., TUBE – to turbocharger, no longer available, order 135725A2 tube and 180428A1
11 1998707C1 1 ADAPTER, turbocharger, 4-23/32 inch (120 mm) long, no longer available, order 135725A2 tube and
12 A170807 1 CLAMP, retaining, special
13 135725A3 1 PIPE ASSY., TUBE – to turbocharger
14 180428A2 1 ADAPTER, turbocharger, 5-23/32 inch (145 mm) long
1 1334628C6 1 GUARD, SHIELD – manifold
2 614-10016 2 BOLT, Hex, M10 x 16, 8.8, Full Thd
3 896-11010 2 WASHER, M10 x 21.5 x 2.5, HT
4 1340698C1 1 SHIELD, turbocharger, see Fig. 2-14, items 16-22 for attaching clamp and hardware, prior to tractor
5 102225A2 1 SHIELD, turbocharger, tractor P.I.N. JJA0064978 and after
6 832-41306 2 NUT, LOCK, M6 x 1, Cl 10, 7220 only, Turbo shield to turbocharger mounting bosses
7 905-10020 3 BOLT, Hex Serr Flg, M10 x 20
8 614-10016 1 BOLT, Hex, M10 x 16, 8.8, Full Thd, If Used
9 896-11010 3 WASHER, M10 x 21.5 x 2.5, HT, If Used
10 614-10016 2 BOLT, Hex, M10 x 16, 8.8, Full Thd
11 1348399C1 2 NUT, hex serrated flange, 10 – 15 mm, replaces 829-2410 flange nut used on some models
12 1968122C1 1 SHIELD, starter, front
13 614-8016 2 BOLT, Hex, M8 x 16, 8.8
14 895-11008 5 WASHER, M8 x 16 x 1.6
15 1289443C1 1 SHIELD, starter, rear
16 614-8012 2 BOLT, Hex, M8 x 12, 8.8, Full Thd
3 J902089 1 SEAL, sealing, pump to block
4 J900227 3 SCREW, Hex, M8 x 1.25 x 22
5 J929458 1 SUPPORT, fan, replaces J910738 support
6 J907769 1 BOLT, BOLT – hex, special, 10 – 1.5 x 70 mm, class 12.9
7 J923044 1 RETAINER, fan hub
8 100-21250 2 RING, SNAP, 2.50″, Int, #250
9 J910739 1 BEARING, BALL
10 J911924 1 HUB, fan
11 845-8050 4 BOLT, Hex Flg, M8 x 50, 8.8, Fan support to cylinder head
12 J914462 1 PULLEY, fan, 11 to 1 ratio
15 J925188 1 SUPPORT, BRACKET – belt tensioner, replaces J911473 bracket
17 J925186 2 SCREW, COUNTERSUNK, Torx Soc, M8 x 1.25 x 25, flat head cap, torx, special, 8 – 1.25 x 25 mm
18 J934817 1 TENSIONER, belt, replaces J918944 tensioner
19 854-10075 1 BOLT, Hex Flg, M10 x 75, 10.9, BOLT – heavy hex flange, 10 – 15 x 75 mm, class 10.9, belt tensioner
20 A77817 1 PACKAGE, REPAIR, KIT – belt tensioner pulley, used to replace pulley of J918944 belt tensioner, item
3 J902089 1 SEAL, sealing
4 J934054 3 BOLT, Hex, flange, 8 – 1.25 x 28 mm, Replaces J926125 bolt
5 J929458 1 SUPPORT, SUPPORT ASSEMBLY – fan
6 J907769 1 BOLT, BOLT – hex, special, 10 – 1.5 x 70 mm, class 12.9
7 J923044 1 RETAINER, fan hub
8 100-21250 2 RING, SNAP, 2.50″, Int, #250
9 J910739 1 BEARING, BALL
10 J911924 1 HUB, fan
11 845-8050 4 BOLT, Hex Flg, M8 x 50, 8.8, Fan support to cylinder head
12 J914462 1 PULLEY, fan, 11 to 1 ratio
13 J925188 1 SUPPORT, BRACKET – belt tensioner
14 J925186 1 SCREW, COUNTERSUNK, Torx Soc, M8 x 1.25 x 25, flat head cap, torx, special, 8 – 1.25 x 25 mm
15 845-8025 1 BOLT, Hex Flg, M8 x 25, 8.8, Mounting bracket to cylinder head
16 J934817 1 TENSIONER, belt, replaces J918944 tensioner
17 854-10075 1 BOLT, Hex Flg, M10 x 75, 10.9, BOLT – heavy hex flange, 10 – 1.5 x 75 mm, class 10.9, belt tensioner
18 A77817 1 PACKAGE, REPAIR, KIT – belt tensioner pulley, used to replace pulley of J918944 belt tensioner, item
1 J924422 1 COVER ASSY, gear, front, prior to engine serial number 45075642
3 J917779 1 GASKET, front gear cover
4 J917316 1 MOTOR HOUSING, gear, prior to engine serial number 45075642, no longer available, order item 4A
5 J281721 1 GASKET, housing, gear, prior to engine serial number 45075642, no longer available, order item 5A
6 J926863 6 BOLT, BOLT – hex flange, 8 – 1.25 x 50 mm, class 10.9, replaces 845-8050 bolt
7 J924962 17 BOLT, hex flange, special, 8 – 1.25 x 16 mm, replaces 845-8016 bolt
8 J926846 5 BOLT, BOLT – hex flange, 8 – 1.25 x 20 mm, class 10.9, replaces 845-8020 bolt
9 J900257 2 PIN, dowel, 16 mm long
10 J903463 1 COVER, front access
11 J903475 1 SEAL, front access cover
12 J914868 1 COVER, PLATE – access cover, flat
13 J931608 1 GASKET, access cover plate, replaces J919601 gasket
14 854-12025 2 BOLT, Hex Flg, M12 x 25, 10.9, Heavy
15 J919683 1 HOUSING, timing pin
16 J915772 1 SEALRING, RING – quad, timing pin housing
17 J907998 2 SCREW, LOCK, Spc Rd Torx Hd, M5 x 17
18 J903924 1 PIN, timing
19 J913994 1 O-RING, sealing
20 100-2587 1 RING, SNAP, 0.875″, Int, #87, (Replaces J904849)
21 J906619 3 PLUG, hex, 1/8 inch PT
22 A77552 1 PLUG, expansion, 29/64 inch diameter
23 A77790 1 KIT, SEALS, oil, crankshaft front
27 J918113 1 SHIELD, dust
1 J926838 1 COVER, gear, front, high PTO
3 J823494 1 SEALANT, Three Bond Silver RTV Adhesive/Sealer, 3 ounce tube, apply between front gear cover and
4 J926719 1 MOTOR HOUSING, gear, high PTO
5 J929253 1 GASKET, housing, gear
6 J926863 6 BOLT, BOLT – hex flange, 8 – 1.25 x 50 mm, class 10.9, front gear cover to timing gear housing to
7 J924962 17 BOLT, hex flange, special, 8 – 1.25 x 16 mm, front gear cover to timing gear housing
8 J926846 5 BOLT, BOLT – hex flange, 8 – 1.25 x 20 mm, class 10.9, timing gear housing to engine block
9 J900257 2 PIN, dowel, 16 mm long
10 J903463 1 COVER, front access
11 J903475 1 SEAL, front access cover
12 J914868 1 COVER, PLATE – access cover, flat
13 J931608 1 GASKET, access cover plate, replaces J919601 gasket
14 854-12025 2 BOLT, Hex Flg, M12 x 25, 10.9, Heavy
15 J919683 1 HOUSING, timing pin
16 J915772 1 SEALRING, RING – quad, timing pin housing
17 J907998 2 SCREW, LOCK, Spc Rd Torx Hd, M5 x 17
18 J903924 1 PIN, timing
19 J913994 1 O-RING, sealing
20 100-2587 1 RING, SNAP, 0.875″, Int, #87, (Replaces J904849)
21 A77790 1 KIT, SEALS, oil, crankshaft front
25 J918113 1 SHIELD, dust
1 J932183 1 MANIFOLD, EXHAUST, exhaust, replaces J906720 and J929779 manifolds
2 J929012 6 GASKET, exhaust manifold, 0.54 mm thick, replaces J921787 gasket
3 J929537 12 BOLT, BOLT – hex, special, exhaust manifold to cylinder head, replaces 814-10070 bolt
4 J914708 12 PLATE, LOCKING, manifold bolt, exhaust
5 J922648 1 COVER ASSY, intake manifold, replaces J906737 cover
6 J914311 1 GASKET, intake manifold cover
7 844-8030 18 BOLT, Hex Flg, M8 x 30, 8.8, Full Thd, BOLT – heavy hex flange, 8 – 1.25 x 30 mm, intake manifold
8 A77429 1 PLUG, hex socket, 1/2 inch PT, intake
1 J932183 1 MANIFOLD, EXHAUST, exhaust, replaces J929779 manifold
2 J929012 6 GASKET, exhaust manifold, 0.54 mm thick, if used
3 614-10020 12 BOLT, Hex, M10 x 20, 8.8, Full Thd, Exhaust manifold to cylinder head
4 J914708 12 PLATE, LOCKING, manifold bolt, exhaust
5 J922648 1 COVER ASSY, intake manifold
6 J914311 1 GASKET, intake manifold cover
7 845-8030 18 BOLT, Hex Flg, M8 x 30, 8.8, Intake manifold cover to cylinder head
8 A77429 1 PLUG, hex socket, 1/2 inch PT, intake
1 J919199 1 TURBOCHARGER, ASSEMBLY – engine, new, parts list Fig. 2-38
2 J818823 4 STUD, turbocharger mounting
3 J818824 4 NUT, hex flange, special, 1.0 mm – 1.5
4 222-993 2 GASKET, 3/8 Tube, Fl, Copper
9 J911941 1 GASKET, mounting, turbocharger
12 J921530 1 HOSE, FLEXIBLE, turbocharger oil supply, replaces J918562 hose
13 J919687 2 CONNECTOR, ELEC, ADAPTER – female hex, special
14 238-5013 1 O-RING, -013, 70 Duro, .426″ ID x .070″ Thk
15 J917417 1 TUBE, drain, oil
16 J914388 1 GASKET, turbo oil drain tube
17 845-8016 2 BOLT, Hex Flg, M8 x 16, 8.8, Full Thd
18 J931970 1 HOSE, 76 mm (3 inch) long, turbocharger oil drain, replaces J903745 hose
19 214-1416 2 CLAMP, HOSE, #16, 0.81/1.50 Type F Worm, Adj.
20 J903744 1 FITTING, PIPE, TUBE – turbocharger oil drain
21 J914944 1 TUBE, air, crossover
22 J916529 2 SLEEVE, TRANSMISSION, HOSE – 76 mm (3 inch) long, crossover tube
23 J924386 4 COLLAR CLAMP, adjustable, special
24 J929779 1 MANIFOLD, exhaust, see Fig. 2-34
25 J906737 1 COVER ASSY, intake manifold, see Fig. 2-34
2 J911941 1 GASKET, mounting, turbocharger
3 J818823 4 STUD, turbocharger mounting
4 J818824 4 NUT, hex flange, special, 10 mm – 1.5
6 J819378 1 GASKET, turbo oil drain
7 844-8020 2 BOLT, Hex Flg, M8 x 20, 8.8
8 J929779 1 MANIFOLD, exhaust, see Fig. 2-34
9 J928629 1 TUBE, oil drain
10 238-7115 2 O-RING, -115, Cl 7, .674″ ID x .103″ Thk
11 J922648 1 COVER ASSY, intake manifold, see Fig. 2-34
12 J914944 1 TUBE, air, crossover
13 J916437 2 HOSE, crossover tube
14 J924386 4 COLLAR CLAMP, adjustable, special, hose retaining
15 J921530 1 HOSE, FLEXIBLE, turbocharger oil supply
16 J919687 2 CONNECTOR, ELEC, ADAPTER – female hex, special
17 238-5013 1 O-RING, -013, 70 Duro, .426″ ID x .070″ Thk
18 222-993 2 GASKET, 3/8 Tube, Fl, Copper
1 J802303 1 TURBOCHARGER, ASSEMBLY – engine, new, replaces J919199 turbocharger assembly
1 J535789 1 TURBOCHARGER, ASSEMBLY – engine, new, replaces J919199 assembly
18 J535243 1 GASKET, adapter
19 J528010 1 ADAPTER, connection, replaces J533030 adapter
20 614-8020 5 BOLT, Hex, M8 x 20, 8.8
21 J534309 2 PLATE, clamping
22 J759917 6 SET SCREW, set, hex head
1 J535106 1 ACTUATOR, turbo wastegate, 7220 Tractor
2 J528177 1 LINK, adjusting
3 425-155 1 NUT, Jam, 5/16″-24, G5, Hex
4 J528204 1 NUT, lock
5 J528221 2 CIRCLIP, retaining
6 895-11008 3 WASHER, M8 x 16 x 1.6
7 J532195 3 SPACER, mounting, short
8 J532196 1 SPACER, mounting, long
9 814-8055 1 BOLT, Hex, M8 x 55, 8.8, BOLT – hex, 8 – 1.25 x 55 mm
10 J533328 1 SUPPORT, BRACKET – wastegate actuator
12 J535874 2 STUD, actuator bracket
1 J918334 1 HEAD, FILTER, filter, oil
2 J906619 2 PLUG, hex, 1/8 inch PT
3 A77722 1 PIN, dowel, locating
4 A77505 1 PLUG, hex socket, 3/4 inch PT, filter head
5 J902338 1 VALVE, PRESSURE RELIEF, relief, pressure
6 J918532 1 PLUNGER, regulator
7 A77541 1 SPRING, compression
8 J919016 1 PLUG, hex, special, 24 mm – 1.50, regulator, if used, with J922882 cover, includes item 9, O-ring
9 238-5022 1 O-RING, -022, 70 Duro, .989″ ID x .070″ Thk, Used with J919016 plug
10 845-8065 11 BOLT, Hex Flg, M8 x 65, 8.8, BOLT – heavy hex flange, 8 – 1.25 x 65 mm, oil filter head to cylinder bloc
11 J919562 1 FILTER, ENGINE OIL, oil, cartridge, engine
12 J921605 1 GASKET, filter head
13 J918175 1 CORE-OIL COOLER
14 J918174 1 GASKET, cooler core
15 J919015 1 THERMOSTAT, temperature
16 A77724 1 O-RING, sealing
17 J922882 1 COVER, oil cooler, no longer available, order J931077 cover and item 8A, J931084 plug
17 J931077 1 COVER, oil cooler, replaces J918403 and J922882 covers
18 J929011 1 GASKET, cooler cover, oil cooler, replaces J918332 gasket
19 J907860 4 BOLT, Hex, Flg Hd, M8 x 25, Spcl
20 217-439 1 PLUG, Hex Soc, 1/2″-14, hex socket headless, 1/2 inch PT, water drain
1 J918334 1 HEAD, FILTER, filter, oil
2 J906619 2 PLUG, hex, 1/8 inch PT
3 A77722 1 PIN, dowel, locating
4 A77505 1 PLUG, hex socket, 3/4 inch PT, filter head
5 J933615 1 VALVE, relief, pressure, replaces J927622 valve
6 J918532 1 PLUNGER, regulator
7 A77541 1 SPRING, compression
8 J919016 1 PLUG, hex, special, 24 mm – 1.50, regulator, if used, with J922882 cover, includes item 9, O-ring
9 238-5022 1 O-RING, -022, 70 Duro, .989″ ID x .070″ Thk, Used with J919016 plug
10 845-8065 11 BOLT, Hex Flg, M8 x 65, 8.8, BOLT – heavy hex flange, 8 – 1.25 x 65 mm, oil filter head to cylinder bloc
11 J919562 1 FILTER, ENGINE OIL, oil, cartridge, engine
12 J921605 1 GASKET, filter head
13 J918175 1 CORE-OIL COOLER
14 J918174 1 GASKET, cooler core
16 A77724 1 O-RING, sealing
17 J922882 1 COVER, oil cooler, no longer available, order J931077 cover and item 8A, J931084 plug
17 J931077 1 COVER, oil cooler, replaces J922882 cover
18 J929011 1 GASKET, cooler cover, oil
19 J907860 4 BOLT, Hex, Flg Hd, M8 x 25, Spcl
20 217-439 1 PLUG, Hex Soc, 1/2″-14, hex socket headless, 1/2 inch PT, water drain
1 J924644 1 PUMP, ENGINE OIL, new, no longer available, order J926201 pump assembly, 24 tooth drive gear
1 J930338 1 PUMP, ENGINE OIL, ASSEMBLY – oil, 24 teeth drive gear, replaces J924644 and J926201 pump
2 614-8030 4 BOLT, Hex, M8 x 30, 8.8, Full Thd
3 J921719 1 TUBE, with screen, oil suction
4 J908738 2 SPACER, mounting
5 845-6030 2 BOLT, Hex Flg, M6 x 30, 8.8, BOLT – heavy hex flange, 6 – 1.0 x 30 mm
6 J914302 1 GASKET, mounting, oil suction tube, Part of the Gasket Kit P/N J914302
7 845-6015 2 BOLT, Hex Flg, M6 x 15, 8.8, Full Thd, BOLT – heavy hex flange, 6 – 1.0 x 15 mm
8 J906216 1 NUT, hex flange, special, 6 mm – 1.0
9 J910960 1 WASHER, flat, special
10 J913427 1 BRACE, suction tube
11 J914015 1 PAN, ENGINE OIL, oil, engine
12 J920400 32 BOLT, Hex, Flg Hd, M8 x 21, Spcl, hex flange cap, special, 8 – 1.25 x 25 mm, oil pan to block, replaces
13 J910266 32 WASHER, spring, Belleville
14 J908316 32 WASHER, flat, special, 9 x 16 x 1 mm
15 J924148 1 PLUG, hex magnetic, special, 22 mm – 1.5, heater hole
16 J902425 1 WASHER, sealing, plug, Part of the Gasket Kit P/N J914302
17 J924147 1 PLUG, hex magnetic, special, 12 mm – 1.5, drain
18 J920773 1 WASHER, SEALING, WASHER – sealing, drain plug, Part of the Gasket Kit P/N J914302
22 196466A1 1 CABLE, ELECTRIC, engine block heater, replaces J905113 cable, oil pan kit
23 J902425 1 WASHER, sealing, plug, oil pan heater kit
1 J930338 1 PUMP, ENGINE OIL, ASSEMBLY – oil, 24 teeth drive gear, replaces J926201 pump
2 J900677 4 BOLT, hex, full threads, 8 – 1.25 x 30 mm, replaces 614-8030 bolt
3 J921719 1 TUBE, with screen, oil suction
4 J926865 2 SPACER, mounting, replaces J908738 spacer
5 845-6030 2 BOLT, Hex Flg, M6 x 30, 8.8, BOLT – heavy hex flange, 6 – 1.0 x 30 mm
6 J914302 1 GASKET, mounting, oil suction tube, Part of the Oil pan gasket kit P/N A77679
7 845-6015 2 BOLT, Hex Flg, M6 x 15, 8.8, Full Thd, BOLT – heavy hex flange, 6 – 1.0 x 15 mm
8 J906216 1 NUT, hex flange, special, 6 mm – 1.0
9 J910960 1 WASHER, flat, special
10 J927611 1 BRACKET, suction tube
11 J914015 1 PAN, ENGINE OIL, oil, engine
12 J920400 32 BOLT, Hex, Flg Hd, M8 x 21, Spcl, hex flange cap, special, 8 – 1.25 x 25 mm, oil pan to block
13 J910266 32 WASHER, spring, Belleville
14 J908316 32 WASHER, flat, special, 9 x 16 x 1 mm
15 J924148 1 PLUG, hex magnetic, special, 22 mm – 1.5, heater hole
16 J902425 1 WASHER, sealing, plug, Part of the oil pan gasket kit P/N A77679
17 J924147 1 PLUG, hex magnetic, special, 12 mm – 1.5, drain
18 J920773 1 WASHER, SEALING, WASHER – sealing, drain plug, Part of the oil pan gasket kit P/N A77679
22 196466A1 1 CABLE, ELECTRIC, engine block heater, replaces J905113, oil pan kit
23 J902425 1 WASHER, sealing, plug, oil pan heater kit
2 J930903 1 COVER, VALVE, replaces J907734 and J927907 covers
3 J905449 1 SEAL, RUBBER, valve cover
4 J910824 6 O-RING, cover bolt, replaces J282133 O-ring
5 J916585 6 SCREW, BOLT – hex flange cap, special
6 J902468 1 PLUG, CAP – oil filler
7 J902466 1 SEAL, cap seal
8 J935585 1 GASKET, cylinder head, standard, replaces J921850 and J928168 gaskets
8 J931026 1 GASKET, cylinder head, 0.25 mm thicker, replaces J921852 and J928180 gaskets
8 J931027 1 GASKET, cylinder head, 0.50 mm thicker replaces J921853 and J928181 gaskets
9 J907861 1 EYE, LIFTING, lifting, front
10 J906440 1 EYE, LIFTING, lifting, rear
11 614-12025 2 BOLT, Hex, M12 x 25, 8.8, Front lifting bracket to cylinder head
12 J920497 1 ELBOW, CONNECTOR – 90 degree, breather vent, no longer available, order J935113 connector and
12 J935113 1 ELBOW, CONNECTOR – 90 degree, breather vent, replaces J920497 connector
13 238-5115 1 O-RING, -115, 70 Duro, .674″ ID x .103″ Thk, If used, used with J920497 connector (Replaces
14 J930827 1 HOSE, 51 mm (2 inch) long, to connector replaces J918610 hose
15 214-1318 1 CLAMP, HOSE, #18, 1 1/8″, Spring
16 J909669 1 TUBE, breather
17 J907741 1 CLIP, CLAMP – P-style, tube retaining
18 J912072 1 SCREW, SELF TAPPING, SCREW – self tapping, hex washer head, special, 8 – 1.25 x 15 mm
19 A77538 1 CLIP, CLAMP – P-style, tube retaining
20 854-12025 1 BOLT, Hex Flg, M12 x 25, 10.9, Heavy
21 J918616 1 HOSE, LARGE, 680 mm (26-3/4 inch) long, tube end
22 J918163 2 CLIP, CLAMP – spring type
24 222-42 1 ELBOW, 90є, 1/2″-24 Fem x 1/8″-27 NPTF, ELBOW – 90 degree, compression, 1/4 tube OD x 1/8 inch
25 J924589 1 TUBE, vent, air
26 222-153 2 SLEEVE, 1/4″ Tube
27 222-22 1 FITTING, 1/2″-24 x 1/8″ NPTF w/Nut, ADAPTER – compression, 1/4 tube OD x 1/8 inch PT, tube to
2 J930903 1 COVER, VALVE, replaces J927907 cover
3 J905449 1 SEAL, RUBBER, valve cover
4 J910824 6 O-RING, cover bolt
5 J922639 6 STUD, STUD – valve cover and tube, wastegate actuator mounting
6 J902468 1 PLUG, CAP – oil filler
7 J902466 1 SEAL, cap seal
8 J935585 1 GASKET, cylinder head, standard, replaces J928168 gasket
8 J931026 1 GASKET, cylinder head, 0.25 mm thicker, replaces J928180 gasket
8 J931027 1 GASKET, cylinder head, 0.50 mm thicker, replaces J928181 gasket
9 J907861 1 EYE, LIFTING, lifting, front
10 J906440 1 EYE, LIFTING, lifting, rear
11 614-12025 2 BOLT, Hex, M12 x 25, 8.8, Front lifting bracket to cylinder head
12 J920497 1 ELBOW, CONNECTOR – 90 degree, breather vent, no longer available, order J935113 connector and
12 J935113 1 ELBOW, CONNECTOR – 90 degree, breather vent, replaces J920497 connector
13 238-5115 1 O-RING, -115, 70 Duro, .674″ ID x .103″ Thk, If used, used with J920497 connector
13 J934865 1 SEAL, O-RING – 17.4 ID x 4.3 mm wide, if used, used with J935113 connector, replaces 238-5115
14 J930827 1 HOSE, 51 mm (2 inch) long, to connector
15 J934496 2 CLIP, CLAMP – spring type, replaces J918163 clamp
16 J909669 1 TUBE, breather
17 J907741 1 CLIP, CLAMP – P-style, tube retaining
18 J912072 1 SCREW, SELF TAPPING, SCREW – self tapping, hex washer head, special, 8 – 1.25 x 15 mm
19 A77538 1 CLIP, CLAMP – P-style, tube retaining
20 854-12025 1 BOLT, Hex Flg, M12 x 25, 10.9, Heavy
21 H353854 1 HOSE ASSY., 813 mm (32 inch) long, cut from 364359C2 bulk hose, tube end, replaces J918616 hose
22 214-1315 1 CLAMP, HOSE, #15, 15/16″, Spring, Replaces 214-1315
24 222-42 1 ELBOW, 90є, 1/2″-24 Fem x 1/8″-27 NPTF, ELBOW – 90 degree, compression, 1/4 tube OD x 1/8 inch
25 J924589 1 TUBE, vent, air
26 222-153 2 SLEEVE, 1/4″ Tube
27 222-22 1 FITTING, 1/2″-24 x 1/8″ NPTF w/Nut, ADAPTER – compression, 1/4 tube OD x 1/8 inch PT, tube to
1 J914310 1 GASKET, thermostat housing
2 J928639 2 THERMOSTAT, engine coolant, replaces J907242 thermostat
3 845-8080 2 BOLT, Hex Flg, M8 x 80, 8.8
5 180811A1 2 PIN, ROLL, PIN – roll, special
6 J912800 1 CONNECTION, TUBE – water outlet
7 J918779 1 GASKET, outlet tube, water
8 845-8095 2 BOLT, Hex Flg, M8 x 95, 8.8, BOLT – heavy hex flange, 8 – 1.25 x 95 mm
9 J918544 1 SUPPORT, mounting, alternator
10 845-8025 4 BOLT, Hex Flg, M8 x 25, 8.8
11 J912837 1 COCK, VALVE – shutoff
12 A77544 1 FILTER, FILTER – water conditioning, precharge
13 238-5111 1 O-RING, -111, 70 Duro, .424″ ID x .103″ Thk
14 A77623 1 ADAPTER, water filter
15 845-6010 1 BOLT, Hex Flg, M6 x 10, 8.8, Full Thd, BOLT – heavy hex flange, 6 – 1.0 x 10 mm
16 J911925 1 COUPLING, hose
17 J911901 1 VALVE, CHECK
1 J914310 1 GASKET, thermostat housing
2 J928639 2 THERMOSTAT, engine coolant
4 845-8080 2 BOLT, Hex Flg, M8 x 80, 8.8
5 J912800 1 CONNECTION, TUBE – water outlet
6 J918779 1 GASKET, outlet tube, water
7 845-8095 2 BOLT, Hex Flg, M8 x 95, 8.8, BOLT – heavy hex flange, 8 – 1.25 x 95 mm
8 J918544 1 SUPPORT, mounting, alternator
9 845-8025 4 BOLT, Hex Flg, M8 x 25, 8.8
10 294926A1 1 VALVE, SHUT-OFF, SHAFT
11 A77544 1 FILTER, water conditioning, precharge
12 238-5111 1 O-RING, -111, 70 Duro, .424″ ID x .103″ Thk
13 A77623 1 ADAPTER, water filter
14 845-6010 1 BOLT, Hex Flg, M6 x 10, 8.8, Full Thd, BOLT – heavy hex flange, 6 – 1.0 x 10 mm
15 J911925 1 COUPLING, hose
16 J911901 1 VALVE, CHECK
1 J920026 1 CYLINDER HEAD, ASSEMBLY – new, without valves, no longer available, order J925644 new head
2 J923564 12 GUIDE, VALVE, valve stem
3 J924582 6 INSERT, INSERT – intake valve, replaces J908830 insert
3 J925468 6 SEAT, VALVE, INSERT – intake valve, 0.254 mm oversize, service repair only, replaces J914839
3 J925470 6 SEAT, VALVE, INSERT – intake valve, 0.508 mm oversize, service repair only, The oversize valve
4 J929005 6 INSERT, seat, exhaust valve, replaces J904716 and J924583 insert
4 J929006 6 INSERT, seat, exhaust valve, 0.254 mm oversize, service repair only, replaces J914386 and J925469
4 J929007 6 INSERT, seat, exhaust valve, 0.508 mm oversize, service repair only, replaces J925471 insert, The
5 A77530 1 PLUG, expansion, 30 mm OD, used with J919919 head assembly
6 A77782 2 PLUG, expansion, 58 mm OD
7 A77590 5 PLUG, expansion, used with J919919 head assembly
8 A77534 1 PLUG, hex, 1/16 inch PT
9 A77428 1 PLUG, hex socket, 1/4 inch PT
10 A77429 2 PLUG, hex socket, 1/2 inch PT
11 J924148 2 PLUG, hex magnetic, special, 22 mm – 1.5, replaces J904386 plug
12 J902425 2 WASHER, sealing, plug
13 J901177 24 KEY, KEEPER – valve
14 J912976 12 RETAINER, valve spring
15 J906412 12 SPRING, VALVE
16 J915707 12 SEAL, intake and exhaust valve stem and guide
17 J924492 6 VALVE, ENGINE, INLET, STD
18 J921444 6 VALVE, ENG EXHAUST, STD
19 J917728 14 BOLT, BOLT – cylinder head, 160 mm long
19 J917729 12 SCREW, BOLT – cylinder head, 80 mm long
20 J925031 12 TAPPET, valve, push rod, replaces J907240 tappet
21 J905194 12 ROD, PUSH, rocker arm
22 J905870 6 SUPPORT, shaft, rocker arm
23 J901693 6 CLAMP, retaining, shaft
24 868-10065 12 SCREW, 12 Pt Hd, M10 x 65, 12.9, BOLT – 12 point flange, 10 – 1.5 x 65 mm, class 12.9
25 J919677 1 MANIFOLD, oil, rocker arm
26 J901717 12 ROCKER, ARM ASSEMBLY
27 J937438 1 SET SCREW, Hex Skt, 3/8″-24 x 33mm, Adj, Ball Point, slotted set, adjusting, special
28 425-116 1 NUT, 3/8″-24, G5, Hex, jam
30 J919435 6 SHAFT, rocker
31 J906100 12 CUP, SPRING, WASHER
32 J907206 12 WASHER, flat, special, end
33 100-1187 12 RING, SNAP, #87, Ext, Replaces B18206
1 J920031 1 CYLINDER HEAD, ASSEMBLY – new, without valves
2 J923564 12 GUIDE, VALVE, valve stem
3 J924582 6 INSERT, INSERT – intake
3 J925468 6 SEAT, VALVE, INSERT – intake, 0.254 mm oversize, service repair only, The oversize valve insert is
3 J925470 6 SEAT, VALVE, INSERT – intake, 0.508 mm oversize, service repair only, The oversize valve insert is
4 J929005 6 INSERT, seat, exhaust valve
4 J929006 6 INSERT, seat, exhaust valve, 0.254 mm oversize, service repair only, The oversize valve insert is not
4 J929007 6 INSERT, seat, exhaust valve, 0.508 mm oversize, service repair only, The oversize valve insert is not
5 J920443 1 PLUG, expansion, 30 mm OD
6 A77782 2 PLUG, expansion, 58 mm OD
7 41-1616 5 PLUG, Cup, 1″, Stainless
8 A77534 1 PLUG, hex, 1/16 inch PT
9 A77428 1 PLUG, hex socket, 1/4 inch PT
10 A77429 2 PLUG, hex socket, 1/2 inch PT
11 J924148 2 PLUG, hex magnetic, special, 22 mm – 1.5
12 J902425 2 WASHER, sealing, plug
13 J901177 24 KEY, KEEPER – valve
14 J906412 12 SPRING, VALVE
15 J912976 12 RETAINER, valve spring
16 J915707 6 SEAL, intake and exhaust valve stem and guide, used on intake valve only on Emissions Certified
17 J924492 6 VALVE, ENGINE, INLET, STD
18 J921444 6 VALVE, ENG EXHAUST, STD
19 J917728 14 BOLT, BOLT – cylinder head, 160 mm long
19 J917729 12 SCREW, BOLT – cylinder head, 80 mm long
20 J931623 12 TAPPET, valve, push rod, replaces J930213 tappet
21 J905194 12 ROD, PUSH, rocker arm
22 J905870 6 SUPPORT, shaft, rocker arm
23 J901693 6 CLAMP, retaining, shaft
24 868-10065 12 SCREW, 12 Pt Hd, M10 x 65, 12.9, BOLT – 12 point flange, 10 – 1.5 x 65 mm, class 12.9
25 J919677 1 MANIFOLD, oil, rocker arm
26 J901717 12 ROCKER, ARM ASSEMBLY
27 J937438 1 SET SCREW, Hex Skt, 3/8″-24 x 33mm, Adj, Ball Point, slotted set, adjusting, special
28 425-116 1 NUT, 3/8″-24, G5, Hex
30 J919435 6 SHAFT, rocker
31 J906100 12 CUP, SPRING, WASHER
32 J907206 12 WASHER, flat, special
33 100-1187 12 RING, SNAP, #87, Ext
1 J917882 1 CAMSHAFT, ASSEMBLY – engine, no longer available, order item 7, J924471 camshaft and item 8
2 J917883 1 PIN, dowel, gear, if used
3 J927155 1 SUPPORT, thrust, camshaft, replaces J914641 support
4 J917328 1 GEAR, camshaft
5 J900227 2 SCREW, Hex, M8 x 1.25 x 22
6 J945329 7 BEARING, CAMSHAFT, camshaft, replaces J901685 bushing
7 J923478 1 CAMSHAFT, engine, replaces J924471 camshaft
8 126-112 1 KEY, WOODRUFF, #6, 5/32″ x 5/8″, HT, If used
1 J923478 1 CAMSHAFT, engine, replaces J924471 camshaft
2 836-4065 1 KEY, WOODRUFF, M4 x 6.5 x 15.72, Replaces 126-112 key
3 J927155 1 SUPPORT, thrust, camshaft
4 J918777 1 GEAR, GEAR – camshaft, steel, replaces J917328 gear
5 J900227 2 SCREW, Hex, M8 x 1.25 x 22
6 J901685 7 BUSHING, camshaft
1 J928964 1 CRANKCASE, BLOCK ASSEMBLY – stripped engine, prior to engine serial number 45636466, no
1 J934900 1 ENGINE, SHORT, BLOCK ASSEMBLY – stripped, engine serial number 45636466 and after, Order
2 J917313 7 CAP, bearing, main
3 J916369 14 SCREW, Hex Flg Hd, M14 x 128, Bearing cap to block
4 J945329 7 BEARING, CAMSHAFT, camshaft, replaces J926152 bushing, see Fig. 2-70, item 6
5 A77782 1 PLUG, expansion, 58 mm OD
6 A77586 1 PLUG, expansion, 43 mm OD
7 A77506 4 PLUG, expansion, 21 mm OD
8 J905401 4 PLUG, expansion, 35 mm OD
9 J920706 1 PLUG, expansion, 22 mm OD
10 A77530 2 PLUG, expansion, 30 mm OD, not used in this application
11 41-3044 1 PLUG, Exp, 2 3/4″, Replaces J901969 plug
12 J901846 4 PIN, dowel
13 J906619 6 PLUG, hex, 1/8 inch PT
14 A77429 4 PLUG, hex socket, 1/2 inch PT
15 A77505 2 PLUG, hex socket, 3/4 inch PT
16 A77533 1 PLUG, hex socket, 1 inch PT
17 J919003 12 NOZZLE INJECTION, piston cooling
18 J900257 2 PIN, dowel, 16 mm long
19 217-103 1 COCK, DRAIN, VALVE – 1/4 inch PT, coolant
20 J903744 1 FITTING, PIPE, TUBE – turbocharger oil drain, see Fig. 2-37 for connecting turbocharger parts
21 J920762 1 ELBOW, HOSE – 79 mm (3-1/8 inch), water
22 J918521 1 CLAMP, HOSE, adj, 1-13/16 – 2-3/4 inch dia, hose, coolant
23 J905408 1 TUBE, oil filler
24 A77424 1 PLUG, CAP – oil fill tube
25 J905778 1 TUBE, oil dipstick
26 J908094 1 DIPSTICK, oil
27 196466A1 1 CABLE, ELECTRIC, engine block heater, replaces J905113 cable
29 J910517 1 O-RING, heater sealing, engine block
1 J934600 1 ENGINE, SKELETON, BLOCK ASSEMBLY – short, new, includes stripped block, pistons, connecting
2 J917313 7 CAP, bearing, main
3 J916369 14 SCREW, Hex Flg Hd, M14 x 128, Bearing cap to block
4 J945329 7 BEARING, CAMSHAFT, camshaft, replaces J901685 bushing, see Fig. 2-72, item 6
5 A77782 1 PLUG, expansion, 58 mm OD
6 A77586 1 PLUG, expansion, 43 mm OD
7 A77506 4 PLUG, expansion, 21 mm OD
8 J905401 4 PLUG, expansion, 35 mm OD
9 J920706 1 PLUG, expansion, 22 mm OD
10 A77530 2 PLUG, expansion, 30 mm OD, upper right-hand rear of block
11 41-3044 1 PLUG, Exp, 2 3/4″
12 J901846 4 PIN, dowel
13 J906619 6 PLUG, hex, 1/8 inch PT
14 A77429 4 PLUG, hex socket, 1/2 inch PT
15 A77505 2 PLUG, hex socket, 3/4 inch PT
16 A77533 1 PLUG, hex socket, 1 inch PT
17 J928031 12 NOZZLE, piston cooling
18 J900257 2 PIN, dowel, 16 mm long
19 217-103 1 COCK, DRAIN, VALVE – 1/4 inch PT, coolant
20 J903744 1 FITTING, PIPE, TUBE – turbocharger oil drain, not used in this application
21 J920762 1 ELBOW, HOSE – 79 mm (3-1/8 inch), water
22 J918521 1 CLAMP, HOSE, adj, 1-13/16 – 2-3/4 inch dia, hose, coolant
23 J905408 1 TUBE, oil filler
24 A77424 1 PLUG, CAP – oil fill tube
25 J928896 1 TUBE, oil dipstick
26 J928895 1 DIPSTICK, oil
27 J926048 1 O-RING, sealing, 66 mm ID
28 196466A1 1 CABLE, ELECTRIC, engine block heater
30 J910517 1 O-RING, heater sealing, engine block
1 J917443 1 CRANKSHAFT, ASSEMBLY – engine, new, no longer available, order J918986 crankshaft assembly
2 J918380 1 GEAR, crankshaft, no longer available, order J918776 gear below
2 J918776 1 GEAR, crankshaft, steel
3 J904483 1 PIN, dowel
5 J925568 1 DAMPER, PULLEY – crankshaft vibration damper
6 J906733 4 BOLT, hex flange, special, 14 x 35 mm
8 J921042 1 COVER, REAR, RETAINER – seal, rear cover
9 J914301 1 GASKET, rear cover retainer
10 845-6015 8 BOLT, Hex Flg, M6 x 15, 8.8, Full Thd, BOLT – heavy hex flange, 6 – 1.0 x 15 mm
11 A77711 6 BEARING LINER, main, upper and lower set, standard
11 A77712 6 BEARING LINER, main, upper and lower set, 0.25 mm undersize
11 A77713 6 BEARING LINER, main, upper and lower set, 0.50 mm undersize
11 A77714 6 BEARING LINER, main, upper and lower set, 0.75 mm undersize
11 A77715 6 BEARING LINER, main, upper and lower set, 1.0 mm undersize
12 A77843 1 BEARING LINER, main thrust, upper and lower set, standard, replaces A77706 bearing
12 A77844 1 BEARING LINER, main thrust, upper and lower set, 0.25 mm undersize, replaces A77707 bearing
12 A77845 1 BEARING LINER, main thrust, upper and lower set, 0.50 mm undersize, replaces A77708 bearing
12 A77846 1 BEARING LINER, main thrust, upper and lower set, 0.75 mm undersize, replaces A77709 bearing
12 A77847 1 BEARING LINER, main thrust, upper and lower set, 1.0 mm undersize, replaces A77710 bearing
12 A77848 1 BEARING, CRANKSHAFT, main thrust, upper and lower set, standard journal diameter, 0.5 mm
12 A77849 1 BEARING, CRANKSHAFT, main thrust, upper and lower set, standard journal diameter, 0.50 mm
12 A77850 1 BEARING, CRANKSHAFT, main thrust, upper and lower set, 0.50 mm undersize journal diameter
13 J918113 1 SHIELD, dust, front seal, order item 14, A77790 kit
14 A77790 1 KIT, SEALS, oil, crankshaft front
18 J918113 1 SHIELD, dust, front seal
19 A77808 1 KIT, SERVICE, wear sleeve, crankshaft front
23 J924987 1 SHIELD, dust
24 A77809 1 KIT, GASKET, oil seal, crankshaft rear; Incl 25, 26
28 A77810 1 KIT, SERVICE, KIT – oil seal, crankshaft rear, Incl 29, 32
1 J917443 1 CRANKSHAFT, ASSEMBLY – engine, new, no longer available, order J918986 crankshaft assembly
1 J918986 1 CRANKSHAFT, ASSEMBLY – engine, new
2 J918380 1 GEAR, crankshaft, no longer available, order J918776 gear below
2 J918776 1 GEAR, crankshaft, steel
3 J904483 1 PIN, dowel
5 J925568 1 DAMPER, PULLEY – crankshaft vibration
6 J906733 4 BOLT, hex flange, special, 14 x 35 mm
8 J933384 1 COVER, REAR, RETAINER – seal, replaces J921042 retainer
9 J914301 1 GASKET, rear cover retainer
10 845-6015 8 BOLT, Hex Flg, M6 x 15, 8.8, Full Thd, BOLT – heavy hex flange, 6 – 1.0 x 15 mm
11 A77711 6 BEARING LINER, main, upper and lower set, standard
11 A77712 6 BEARING LINER, main, upper and lower set, 0.25 mm undersize
11 A77713 6 BEARING LINER, main, upper and lower set, 0.50 mm undersize
11 A77714 6 BEARING LINER, main, upper and lower set, 0.75 mm undersize
11 A77715 6 BEARING LINER, main, upper and lower set, 1.0 mm undersize
12 A77843 1 BEARING LINER, main thrust, upper and lower set, standard, replaces A77706 bearing
12 A77844 1 BEARING LINER, main thrust, upper and lower set, 0.25 mm undersize, replaces A77707 bearing
12 A77845 1 BEARING LINER, main thrust, upper and lower set, 0.50 mm undersize, replaces A77708 bearing
12 A77846 1 BEARING LINER, main thrust, upper and lower set, 0.75 mm undersize, replaces A77709 bearing
12 A77847 1 BEARING LINER, main thrust, upper and lower set, 1.0 mm undersize, replaces A77710 bearing
12 A77848 1 BEARING, CRANKSHAFT, main thrust, upper and lower set, standard journal diameter, 0.25 mm
12 A77849 1 BEARING, CRANKSHAFT, main thrust, upper and lower set, standard journal diameter, 0.50 mm
12 A77850 1 BEARING, CRANKSHAFT, mam thrust, upper and lower set, 0.50 mm undersize journal diameter
13 J918113 1 SHIELD, dust, front seal, order item 14, A77790 kit
14 A77790 1 KIT, SEALS, oil, crankshaft front
18 J918113 1 SHIELD, dust, front seal
19 A77808 1 KIT, SERVICE, wear sleeve, crankshaft front
23 J924987 1 SHIELD, dust
24 J934486 1 KIT, SERVICE, KIT – oil seal, crankshaft rear, replaces A77809 kit
28 A77810 1 KIT, SERVICE, KIT – oil seal, crankshaft rear, includes wear sleeve
1 J909939 1 FLYWHEEL, ASSEMBLY – engine, no longer used, for service order item 5, J934838 flywheel assembly
2 J905031 1 GEAR, GEAR – flywheel
3 J901395 8 SCREW, Hex, M12 x 1.25 x 32, Spc
4 J900269 8 WASHER, flat, special, retaining
5 J934838 1 FLYWHEEL, ASSEMBLY – engine, replaces J925872 flywheel assembly
6 J905031 1 GEAR, GEAR – flywheel
7 119491A1 1 HOUSING, flywheel
8 375362R1 2 PIN, dowel, 1/2 x 1-3/8 inch
9 93141C1 1 PLUG, cup (Use without MFD)
13 J910248 1 PLUG, flywheel housing, replaces J904470 plug
14 238-5212 1 O-RING, -212, 70 Duro, .859″ ID x .139″ Thk, (Replaces J904469)
15 828-16060 1 BOLT, Hex, M16 x 60, 10.9, Full Thd, Flywheel housing to top of clutch housing
15 628-16050 1 BOLT, Hex, M16 x 50, 10.9, Full Thd, Flywheel housing to top of clutch housing
15 828-12050 2 BOLT, Hex, M12 x 50, 10.9, Flywheel housing to bottom of clutch housing
15 628-22065 2 BOLT, Hex, M22 x 65, 10.9, Full Thd, BOLT – hex, full threads, 22 – 2.5 x 65 mm, class 10.9, flywheel
15 828-20070 2 BOLT, Hex, M20 x 70, 10.9, Full Thd, Flywheel housing to center of side channel
15 827-12065 2 BOLT, Hex, M12 x 65, 10.9, hex, 12 – 1.75 x 65 mm, class 10.9, speed housing to top of flywheel
16 A157918 10 WASHER, flat, 12 mm, flywheel housing into engine
16 896-15012 2 WASHER, M12 x 28.5 x 4, HT, flat, 13.5 x 28 x 4 mm, hardened, speed housing to top of flywheel
16 1289123C1 2 WASHER, flat, 22 mm, flywheel housing to side of clutch housing
16 A177650 2 WASHER, flat, flywheel housing to center of side channel
16 896-15012 2 WASHER, M12 x 28.5 x 4, HT, flat, 13.5 x 28 x 4 mm, hardened, speed housing to top of flywheel
17 892-11012 2 WASHER, LOCK, M12, Flywheel Housing into Engine
18 896-16012 4 WASHER, M12 x 28.5 x 4, HT, flat, 13.5 x 28 x 4 mm, hardened
21 92590C2 1 PLATE, drive
22 614-12025 6 BOLT, Hex, M12 x 25, 8.8
23 896-11012 6 WASHER, M13.5 x 24.5 x 3, HT
25 614-12040 2 BOLT, Hex, M12 x 40, 8.8, Full Thd, (Plug hole without MFD)
26 832-41312 2 NUT, LOCK, M12 x 1.75, Cl 10, (Plug hole without MFD)
1 J934838 1 FLYWHEEL, ASSEMBLY – engine, replaces J925872 flywheel assembly
2 J905031 1 GEAR, GEAR – flywheel
3 J901395 8 SCREW, Hex, M12 x 1.25 x 32, Spc
4 J900269 8 WASHER, flat, special, retaining
5 119491A1 1 HOUSING, flywheel
6 375362R1 2 PIN, dowel, 1/2 x 1 -3/8 inch
7 93141C1 1 PLUG, cup (Use without MFD)
8 J910248 1 PLUG, flywheel housing
9 238-5212 1 O-RING, -212, 70 Duro, .859″ ID x .139″ Thk
10 828-12050 12 BOLT, Hex, M12 x 50, 10.9, Flywheel housing into engine
10 828-16060 1 BOLT, Hex, M16 x 60, 10.9, Full Thd, Flywheel housing to top of clutch housing
10 628-16050 1 BOLT, Hex, M16 x 50, 10.9, Full Thd, Flywheel housing to top of clutch housing
10 828-12050 2 BOLT, Hex, M12 x 50, 10.9, Flywheel housing to bottom of clutch housing
10 628-22065 2 BOLT, Hex, M22 x 65, 10.9, Full Thd, BOLT – hex, full threads, 22 – 2.5 x 65 mm, class 10.9, flywheel
10 828-20070 2 BOLT, Hex, M20 x 70, 10.9, Full Thd, Flywheel housing to center of side channel, if used
10 827-12065 2 BOLT, Hex, M12 x 65, 10.9, hex, 12 – 1.75 x 65 mm, class 10.9, speed housing to top of flywheel
11 A157918 10 WASHER, flat, 12 mm, flywheel housing into engine
11 896-16016 2 WASHER, M16 x 34.5 x 5, HT, flat, 17.5 x 34 x 5 mm, hardened, flywheel housing to top of clutch
11 896-15012 2 WASHER, M12 x 28.5 x 4, HT, flat, 13.5 x 28 x 4 mm, hardened, flywheel housing to bottom of clutch
11 1289123C1 2 WASHER, flat, 22 mm, flywheel housing to side of clutch housing
11 A177650 2 WASHER, flat, flywheel housing to center of side channel, if used
11 896-15012 2 WASHER, M12 x 28.5 x 4, HT, flat, 13.5 x 28 x 4 mm, hardened, speed housing to top of flywheel
12 892-11012 2 WASHER, LOCK, M12, Flywheel Housing into Engine
13 896-16012 4 WASHER, M12 x 28.5 x 4, HT, flat, 13.5 x 28 x 4 mm, hardened, if used
14 92590C2 1 PLATE, drive
15 614-12025 6 BOLT, Hex, M12 x 25, 8.8
16 896-11012 6 WASHER, M13.5 x 24.5 x 3, HT
17 614-12040 2 BOLT, Hex, M12 x 40, 8.8, Full Thd, (Plug hole without MFD)
18 832-41312 2 NUT, LOCK, M12 x 1.75, Cl 10, (Plug hole without MFD)
1 J919937 1 SLEEVE CYLINDER, piston
2 J907177 1 O-RING, sealing, sleeve
4 100-21175 2 RING, SNAP, 1.75″, Int, #175, (Replaces G109044)
5 A77802 1 RING SET, PISTON, KIT – used with piston stamped 9564 or 3163
9 J901597 1 PIN, piston
2 J913990 1 BUSHING, connecting rod
3 J928870 2 BOLT, BOLT – special, rod, bearing cap, replaces J920799 and J924351 bolts
4 J901381 2 NUT, hex, rod bolt, bolt retaining
5 A77563 6 BEARING LINER, KIT – upper and lower, standard
5 A77564 6 BEARING LINER, KIT – upper and lower, 0.25 mm undersize
5 A77565 6 BEARING LINER, KIT – upper and lower, 0.50 mm undersize
5 A77566 6 BEARING LINER, KIT – upper and lower, 0.75 mm undersize
5 A77567 6 BEARING LINER, KIT – upper and lower, 1.00 mm undersize
1 J919937 1 SLEEVE CYLINDER, piston
2 J907177 1 O-RING, sealing, cylinder sleeve, piston
4 100-21175 2 RING, SNAP, 1.75″, Int, #175, Piston
5 A77802 1 RING SET, PISTON, KIT
2 J907177 1 O-RING, sealing, cylinder sleeve, piston
4 100-21175 2 RING, SNAP, 1.75″, Int, #175, Piston
5 J802429 1 KIT, PISTON RINGS
9 J901597 6 PIN, piston
11 J913990 1 BUSHING, connecting rod
12 J928870 2 BOLT, BOLT – special, rod, bearing cap, connecting
13 J934864 2 NUT, hex, rod bolt, replaces J901381 nut, connecting
14 A77563 6 BEARING LINER, KIT – upper and lower, standard, connecting rod
14 A77564 6 BEARING LINER, KIT – upper and lower, 0.25 mm undersize, connecting rod
14 A77565 6 BEARING LINER, KIT – upper and lower, 0.50 mm undersize, connecting rod
14 A77566 6 BEARING LINER, KIT – upper and lower, 0.75 mm undersize, connecting rod
14 A77567 6 BEARING LINER, KIT – upper and lower, 1.00 mm undersize, connecting rod
1 A77854 6 PACKAGE, REPAIR, KIT – piston and sleeve, engine, see fig. 2-106, Prior to Engine Serial Number
2 A77563 6 BEARING LINER, KIT – upper and lower, standard, see fig. 2-106, Prior to Engine Serial Number
3 J901597 6 PIN, piston, see fig. 2-106, Prior to Engine Serial Number 45636466
4 A77711 6 BEARING LINER, main, upper and lower set, standard, see fig. 2-94, Prior to Engine Serial Number
5 A77872 1 KIT, GASKET, valve grind, includes high temperature exhaust manifold gasket, see fig. 2-110, Prior to
6 J935585 1 GASKET, cylinder head, standard, see fig.. 2-56, Prior to Engine Serial Number 45636466
7 A77679 1 KIT, GASKET, oil pan, see fig. 2-52, Prior to Engine Serial Number 45636466
2 A77563 6 BEARING LINER, KIT – upper and lower, standard, see fig. 2-106, Engine Serial Number 45636467
3 J901597 6 PIN, piston, see fig. 2-106, Engine Serial Number 45636467 and After
4 A77711 6 BEARING LINER, main, upper and lower set, standard, see fig. 2-94, Engine Serial Number 45636467
5 A77872 1 KIT, GASKET, valve grind, includes high temperature exhaust manifold gasket, see fig. 2-110, Engine
6 J935585 1 GASKET, cylinder head, standard, see fig. 2-56, Engine Serial Number 45636467 and After
7 A77679 1 KIT, GASKET, oil pan, see fig. 2-52, Engine Serial Number 45636467 and After
1 J914310 1 GASKET, thermostat housing
2 J918779 1 GASKET, outlet tube, water, thermostat housing
3 J915707 12 SEAL, intake and exhaust valve stem and guide
4 J911941 1 GASKET, mounting, turbocharger
5 J929012 6 GASKET, exhaust manifold, 0.54 mm thick, replaces J921787 gasket
6 J914311 1 GASKET, intake manifold cover
7 J914388 1 GASKET, turbo oil drain tube, turbocharger
8 J902466 1 SEAL, cap, oil fill cap to valve cover
9 J905449 1 SEAL, RUBBER, valve cover, rocker
10 J910824 6 O-RING, cover bolt
11 J909886 6 SEAL, SLEEVE – injector
12 J903380 7 SEAL, connector, fuel injection nozzle
13 238-5115 1 O-RING, -115, 70 Duro, .674″ ID x .103″ Thk, Connector to valve cover
14 J906659 6 SEAL, injector nozzle, 7 mm injector tip
15 238-5111 1 O-RING, -111, 70 Duro, .424″ ID x .103″ Thk, Water filter shutoff valve
16 J918610 1 HOSE, LARGE, 51 mm (2 inch) long, breather tube to connector
17 J919677 1 MANIFOLD, oil, rocker arm
18 J914708 12 PLATE, LOCKING, bolt, exhaust manifold
19 J823921 1 GAUGE, cylinder head, bolt length
1 J914310 1 GASKET, thermostat housing
2 J918779 1 GASKET, outlet tube, water
3 J915707 6 SEAL, intake and exhaust valve stem and guide, used on intake valve only on Emissions Certified
4 J911941 1 GASKET, mounting, turbocharger
5 J929012 6 GASKET, exhaust manifold, 0.54 mm thick
6 J914311 1 GASKET, intake manifold cover
7 J931350 1 GASKET, turbo oil drain tube, replaces J928919 gasket
9 J905449 1 SEAL, RUBBER, valve cover
10 J910824 6 O-RING, cover bolt
11 J909886 6 SEAL, SLEEVE – injector
12 J903380 7 SEAL, connector, fuel injection nozzle
13 238-5115 1 O-RING, -115, 70 Duro, .674″ ID x .103″ Thk, Connector to valve cover
14 J923261 6 WASHER, SEAL – injector nozzle, 2.5 mm thick, 7 mm injector tip
15 238-5111 1 O-RING, -111, 70 Duro, .424″ ID x .103″ Thk, Water filter shutoff valve
16 J930827 1 HOSE, 51 mm (2 inch) long, breather tube to connector, replaces J918610 hose
17 J919677 1 MANIFOLD, oil, rocker arm
18 J914708 12 PLATE, LOCKING, exhaust manifold bolt
19 J823921 1 GAUGE, cylinder head, bolt length
1 J903475 1 SEAL, front access cover
2 J917779 1 GASKET, front gear cover, high mount engine, used in A77726 kit
2 J917780 1 SEAL, GASKET – front gear cover, low mount engine, not used in this application, use J917779 gasket
3 J281721 1 GASKET, housing, gear used in A77726 kit only
4 J915772 1 SEALRING, RING – quad, timing pin housing
5 J919601 1 GASKET, access cover plate
6 J902089 1 SEAL, sealing, water pump
7 J914301 1 GASKET, rear cover retainer, crankshaft
8 J918174 1 GASKET, cooler core, oil cooler
9 J929011 1 GASKET, cooler cover, oil cooler, replaces J918332 gasket
10 J901798 1 WASHER, SEALING, WASHER – sealing, not used in this application
11 J912473 1 SEALRING, flywheel housing to block, not used in this application
12 J923054 1 GASKET, mounting, fuel transfer pump, replaces J914304 gasket
13 238-5212 1 O-RING, -212, 70 Duro, .859″ ID x .139″ Thk, Not used in this application
14 J907177 6 O-RING, sealing, sleeve
15 J913994 1 O-RING, sealing
1 J903475 1 SEAL, front access cover
2 J929253 1 GASKET, housing, gear
3 J915772 1 SEALRING, RING – quad, timing pin housing
4 J931608 1 GASKET, access cover plate, replaces J919601 gasket
5 J902089 1 SEAL, sealing, water pump
6 J914301 1 GASKET, rear cover retainer, crankshaft
7 J918174 1 GASKET, cooler core, oil
8 J929011 1 GASKET, cooler cover, oil
9 J901798 1 WASHER, SEALING, WASHER – sealing
10 J931059 1 GASKET, mounting, fuel transfer pump, replaces J923054 gasket
11 J912473 1 SEALRING, flywheel housing to block
12 238-5212 1 O-RING, -212, 70 Duro, .859″ ID x .139″ Thk
13 J907177 6 O-RING, sealing, sleeve
14 J913994 1 O-RING, sealing
15 J916284 1 O-RING, O-RING
16 J926722 1 SEAL, RING – quad, fuel injection pump
17 J931351 1 GASKET, gear housing
1 J922145 1 PUMP, FUEL INJECTION, ASSEMBLY – fuel, new, 7220 Tractor only prior to Tractor P.I.N.
3 J909886 6 SEAL, SLEEVE – injector
4 J910279 6 CLAMP, fuel injector
5 845-8080 6 BOLT, Hex Flg, M8 x 80, 8.8
6 J906783 1 TUBE, fuel injector, No. 1 cylinder
7 J906784 1 TUBE, fuel injector, No. 2 cylinder
8 J906785 1 TUBE, fuel injector, No. 3 cylinder
9 J917776 2 BRACE, BRACKET – fuel tube
10 J917747 4 CLAMP, fuel tube
11 J904519 2 SUPPORT, tube retaining
12 J920854 4 SCREW, Hex Hd, M5 x .8 x 20, w/LW, Replaces J917712 bolt and J903723 washer
14 J910521 1 TUBE, fuel injector No. 4 cylinder
15 J906787 1 TUBE, fuel injector, No. 5 cylinder
16 J906788 1 TUBE, fuel injector, No. 6 cylinder
18 J903380 6 SEAL, connector
19 J905307 6 BOLT, BANJO, M6 x 1 x 14.3, BOLT – banjo drain, special
20 J920595 1 TUBE ASSY., fuel drain
21 J924726 1 BOLT, BANJO, check, replaces J916360 valve
22 J918188 2 WASHER, sealing
1 J926878 1 PUMP, FUEL INJECTION, ASSEMBLY – fuel, new, parts list fig. 3-16
2 J930525 6 INJECTOR ASSY., fuel, parts list fig.3-20
3 J909886 6 SEAL, SLEEVE – injector, sealing
4 J910279 6 CLAMP, fuel injector
5 J922018 6 SCREW, BOLT – heavy hex flange, 8 – 1.25 x 80 mm, class 12.9
6 J930442 1 PIPE INJECTION, TUBE – fuel, No. 1 cylinder
7 J930443 1 PIPE INJECTION, TUBE – fuel, No. 2 cylinder
8 J930444 1 PIPE INJECTION, TUBE – fuel, No. 3 cylinder
9 J917716 1 BRACE, BRACKET – fuel tube, supply
11 J920854 5 SCREW, Hex Hd, M5 x .8 x 20, w/LW
12 J904519 3 SUPPORT, tube retaining
13 J917747 6 CLAMP, fuel tube
14 J917777 2 BRACE, fuel tube
16 J920855 2 BOLT, hex, captive washer, special, 5 – 0.8 x 35 mm
17 J917717 1 BRACE, BRACKET – fuel tube
18 J917746 2 CLAMP, fuel tube
19 J904711 1 CLAMP, BRACKET – fuel tube
20 J930445 1 PIPE INJECTION, TUBE – fuel, No. 4 cylinder
21 J930446 1 PIPE INJECTION, TUBE – fuel, No. 5 cylinder
22 J930447 1 PIPE INJECTION, TUBE – fuel, No. 6 cylinder
24 J903380 6 SEAL, connector
25 J905307 6 BOLT, BANJO, M6 x 1 x 14.3, BOLT – banjo drain, special
26 J920595 1 TUBE ASSY., fuel drain
27 J924726 1 BOLT, BANJO, check
28 J918188 2 WASHER, sealing, banjo fitting
29 J916779 1 HOSE, FLEXIBLE, 508 mm (20 inch) long, cylinder block to injection pump
30 222-762 1 ELBOW, 90є, 7/16″-20, 45є Fl x 1/8″ NPT, 90 degree, 7/16-20 45 degree flare x 1/8 inch PT
31 J918002 1 BOLT, BANJO, banjo, hose to injection pump
32 J918190 2 WASHER, SEALING, WASHER – sealing, special, 10 x 15.5 x 1 mm
1 J908110 1 PLUG, threaded
2 J906619 1 PLUG, hex, 1/8 inch PT
3 J921594 1 PLUG, threaded orifice, cylinder head to tee
4 J902425 2 WASHER, sealing, plug
5 217-1061 1 TEE, 1/8″-27 Female x 1/8″-27 Male Run, street, 1/8 inch female PT branch x female PT x PT
6 222-21 1 FITTING, 7/16″-24 x 1/8″ NPTF, Tee to aneroid tube
7 J926739 1 TUBE, aneroid, nylon
8 J903035 1 BOLT, BANJO, hex, 12 – 1.5 x 24 mm
9 J919644 1 FITTING, CONNECTOR – banjo
10 J935171 2 WASHER, SEALING, special, 12 x 19 x 1.5 mm, replaces J918191 washer
11 A77796 1 CONNECTOR, ADAPTER – straight, 1/4 barb end x 1/8 inch PT, tee to wastegate tube
12 J926969 1 TUBE, wastegate
13 222-102 1 SLEEVE, 1/4″ Tube
14 825-2410 1 NUT, M10 x 1.5, Flg, Cl 8, Wastegate tube to valve cover
15 J920871 1 HOSE, 1294 mm (51 inch) long
16 214-1404 2 CLAMP, HOSE, #4, 0.25/0.62 Type M Worm, adj, 1/4 – 5/8 inch dia
17 J926878 1 PUMP, FUEL INJECTION, ASSEMBLY – fuel, new, parts list fig. 3-16
18 J535106 1 ACTUATOR, turbo wastegate, see fig. 2-44
19 217-1034 1 REDUCER, 1/4″-18 Male NPTF x 1/8″-27 Female NPTF, Intake manifold, Not shown
1 J897331 1 SUPPORT, HEAD – fuel filter, replaces J915240 head
3 J906694 1 SEALRING, sealing, 70 mm ID, filter head
4 J906695 1 SEALRING, sealing, 14 mm ID, adapter
5 J903293 1 NUT, hex, special, 16 mm – 2.0
6 J925955 1 ADAPTER, fuel filter, replaces J903845 adapter
7 J930942 1 FILTER, FUEL, Primary, Replaces J925274 filter
8 J903640 1 FILTER, FUEL, secondary
9 J912923 1 TUBE, fuel supply
10 J914711 1 CLIP, CLAMP – P-type
11 J935171 2 WASHER, SEALING, special, 12 x 19 x 1.5 mm, replaces J918191 washer
14 J918192 4 RING, PACKING, WASHER – sealing, special, 14 x 20 x 1 mm
15 J907541 1 JACK SCREW, BOLT – banjo connector
16 J933252 1 PUMP, FEED, lift, fuel, see J926764 repair kit below, replaces J917998 pump
17 J931059 1 GASKET, mounting, fuel transfer pump, replaces J923054 gasket
18 845-8020 2 BOLT, Hex Flg, M8 x 20, 8.8, Full Thd
19 J906790 1 TUBE, supply
20 J935171 2 WASHER, SEALING, special, 12 x 19 x 1.5 mm, replaces J918191 washer
21 J916361 1 BOLT, BANJO, banjo connector, 12 – 1.5 x 24 mm
22 J911447 1 CONNECTOR, banjo, fuel return
24 J926764 1 KIT, GASKET, transfer pump repair, no longer available, identify and order complete pump assembly
30 J923054 2 GASKET, mounting, fuel transfer pump, replaces J914304 gasket
1 J897331 1 SUPPORT, HEAD – fuel filter
3 J906694 1 SEALRING, sealing, 70 mm ID, filter head
4 J906695 1 SEALRING, sealing, 14 mm ID, adapter
5 J903293 1 NUT, hex, special, 16 mm – 2.0
6 J925955 1 ADAPTER, fuel filter
7 J930942 1 FILTER, FUEL, Primary, Replaces J925274 filter
8 J903640 1 FILTER, FUEL, secondary
9 J918873 1 TUBE, supply, fuel
10 J914711 1 CLIP, CLAMP – P-type
11 J935171 2 WASHER, SEALING, special, 12 x 19 x 1.5 mm, replaces J918191 washer
12 J911446 1 BOLT, BANJO, M12 x 1.5 x 24
13 J905860 1 SCREW, BOLT ASSEMBLY – banjo hex, special
14 J918192 4 RING, PACKING, WASHER – sealing, special, 14 x 20 x 1 mm
15 J924725 1 BOLT, BANJO, connector
16 J933252 1 PUMP, FEED, lift, fuel, see J926764 repair kit below, replaces J925709 pump
17 J931059 1 GASKET, mounting, fuel transfer pump, replaces J923054 gasket
18 844-8020 2 BOLT, Hex Flg, M8 x 20, 8.8
19 J918537 1 TUBE, supply, used with items 32, 33 and 34, if used
20 J935171 2 WASHER, SEALING, special, 12 x 19 x 1.5 mm, replaces J918191 washer
21 J916361 1 BOLT, BANJO, banjo connector, 12 – 1.5 x 24 mm
22 J911447 1 CONNECTOR, banjo, fuel return
23 J912886 1 VALVE, overflow, see item 6, fig. 3-16
24 J926764 1 KIT, GASKET, transfer pump repair, no longer available, identify and order complete pump assembly
30 J923054 2 GASKET, mounting, fuel transfer pump
32 J914037 1 JACK SCREW, banjo connector, if used
33 217-432 1 PLUG, Hex Soc, 1/4″-18, hex socket headless, 1/4 inch PT, if used
34 J918192 2 RING, PACKING, WASHER – sealing, special, 14 x 20 x 1 mm, if used
1 J922145 1 PUMP, FUEL INJECTION, ASSEMBLY – fuel, new
2 A77720 1 PIN, timing
3 3051337R1 1 WASHER, SEALING, M18 x 24 x 1.5, WASHER – sealing
4 J912888 1 PLUG, timing
5 A41856 1 O-RING, sealing
6 J913681 1 JACK SCREW, VALVE – bolt, overflow
7 933697R1 1 WASHER, SEALING, M10 x 13.5 x 1, WASHER – valve sealing
8 J923230 1 LEVER, pump shutoff
10 691292C1 1 RETAINER, HOUSING – spring return
11 A71110 1 GASKET, mounting
12 A77775 1 WASHER, lock
13 A41852 1 NUT, hex, self-locking
14 1808728C1 1 LEVER, throttle control
15 829-1306 1 NUT, M6, Cl 10
16 892-11006 1 WASHER, LOCK, M6
17 895-11006 1 WASHER, M6
18 1808822C1 1 THUMB SCREW, M6 x 26, BOLT – throttle lever
19 680187C1 1 O-RING, sealing, special
20 J912614 1 GEAR, fuel pump
21 J916284 1 O-RING, O-RING – sealing, fuel pump to gear housing
22 J915036 4 STUD, pump mounting
23 825-2410 4 NUT, M10 x 1.5, Flg, Cl 8
24 J928160 1 VALVE, SOLENOID, fuel shutoff, 12 volt, replaces J923257 solenoid
25 A77807 1 SET, KIT – plunger, ball socket and clip, no longer available, order one each of items 31 and 32
26 492-11025 1 WASHER, LOCK, 1/4″
27 425-154 1 NUT, Jam, 1/4″-28, G5
28 J925171 1 BOOT, protective, plunger
29 473321C1 1 STRAP, CABLE, .098″ x 8″, tie
30 J923887 1 SPRING, return, plunger
31 J923885 1 SPRING, CLIP – spring
32 J928173 1 BALL JOINT, SOCKET
33 97006C1 2 BOLT, BOLT – hex flange, special, 6 – 1 x 20 mm
34 J923254 1 SUPPORT, BRACKET – solenoid mounting
35 854-10020 2 BOLT, Hex Flg, M10 x 20, 10.9
36 832-10405 1 NUT, LOCK, M5 x .8, Cl 8
1 J926878 1 PUMP, FUEL INJECTION, ASSEMBLY – fuel, new
2 A77720 1 PIN, timing
3 3051337R1 1 WASHER, SEALING, M18 x 24 x 1.5, WASHER – sealing, plug
4 J912888 1 PLUG, timing
5 A41856 1 O-RING, sealing
6 J912886 1 VALVE, overflow
7 933697R1 1 WASHER, SEALING, M10 x 13.5 x 1, WASHER – valve sealing
8 J929322 1 LEVER, pump shutoff, not shown
9 J930291 1 NUT, hex, 5 mm – 0.8, not shown
10 691292C1 1 RETAINER, HOUSING – spring return
11 680187C1 1 O-RING, sealing, special
12 1808728C1 1 LEVER, throttle control
13 J913320 1 SCREW, vent
14 691273C1 1 GASKET, vent screw
15 J912897 1 WASHER, lock
16 J912896 1 NUT, hex, self-locking, special
18 B41211 1 SCREW, vent
19 933696R1 1 WASHER, SEALING, M6 x 10 x 1, 6 x 10 mm, vent screw
20 1808822C1 1 THUMB SCREW, M6 x 26, BOLT – throttle lever
21 895-11006 1 WASHER, M6
22 892-11006 1 WASHER, LOCK, M6
23 829-1306 1 NUT, M6, Cl 10
24 J912615 1 GEAR, fuel pump
25 J916284 1 O-RING, O-RING
26 J915036 4 STUD, pump mounting, gear housing to injection pump
27 825-2410 4 NUT, M10 x 1.5, Flg, Cl 8
28 97006C1 2 BOLT, BOLT – hex flange, special, 6 – 1 x 20 mm
29 J923255 1 SUPPORT, BRACKET – solenoid mounting
30 844-10020 2 BOLT, Hex Flg, M10 x 20, 8.8
31 J930233 1 SOLENOID, fuel shutoff, 12 volt
32 A146456 1 BALL, JOINT – 1/4 inch NF
33 492-11025 1 WASHER, LOCK, 1/4″
34 425-154 1 NUT, Jam, 1/4″-28, G5
35 J925171 1 BOOT, protective, plunger
36 473321C1 1 STRAP, CABLE, .098″ x 8″, tie
37 J923887 1 SPRING, return, plunger
38 J918176 1 HOSE, 330 mm (13 inch) long, fuel drain, engine serial number 45361256 and below. Use with
38 J930842 1 HOSE, 330 mm (13 inch) long, fuel drain, engine serial number 45361257 and above. Use with
39 A171099 1 CLAMP, HOSE, spring-type, hose
40 J930683 1 NUT, LOCK, hex, 5 mm – 0.8, solenoid ball joint to injection pump, not shown
1 J909886 1 SEAL, SLEEVE – injector
2 J903380 1 SEAL, connector
3 J908507 1 INJECTOR ASSY., fuel, Whenever a nozzle is removed from the cylinder head, J906659 seal, item 11
5 1806233C1 5 SHIM, nozzle, 1.00 mm
5 1806234C1 5 SHIM, nozzle, 1.04 mm
5 1806235C1 5 SHIM, nozzle, 1.08 mm
5 1806236C1 5 SHIM, nozzle, 1.10 mm
5 1806237C1 5 SHIM, nozzle, 1.14 mm
5 1806238C1 5 SHIM, nozzle, 1.18 mm
5 1806239C1 5 SHIM, nozzle, 1.20 mm
5 1806240C1 5 SHIM, nozzle, 1.24 mm
5 1806241C1 5 SHIM, nozzle, 1.28 mm
5 1806242C1 5 SHIM, nozzle, 1.30 mm
5 1806243C1 5 SHIM, nozzle, 1.34 mm
5 1806244C1 5 SHIM, nozzle, 1.38 mm
5 1806245C1 5 SHIM, nozzle, 1.40 mm
5 1806246C1 5 SHIM, nozzle, 1.44 mm
5 1806247C1 5 SHIM, nozzle, 1.48 mm
5 1806248C1 5 SHIM, nozzle, 1.50 mm
5 1806249C1 5 SHIM, nozzle, 1.54 mm
5 1806250C1 5 SHIM, nozzle, 1.58 mm
5 1806251C1 5 SHIM, nozzle, 1.60 mm
5 1806252C1 5 SHIM, nozzle, 1.64 mm
5 1806253C1 5 SHIM, nozzle, 1.68 mm
5 1806254C1 5 SHIM, nozzle, 1.70 mm
5 1806255C1 5 SHIM, nozzle, 1.74 mm
5 1806256C1 5 SHIM, nozzle, 1.78 mm
5 1806257C1 5 SHIM, nozzle, 1.80 mm
5 1806258C1 5 SHIM, nozzle, 1.84 mm
5 1806259C1 5 SHIM, nozzle, 1.88 mm
5 1806260C1 5 SHIM, nozzle, 1.90 mm
5 1806261C1 5 SHIM, nozzle, 1.94 mm
5 1806262C1 5 SHIM, nozzle, 1.98 mm
11 J906659 6 SEAL, injector nozzle, 7 mm injector tip, Whenever a nozzle is removed from the cylinder head
1 J909886 1 SEAL, SLEEVE – injector, sealing
2 J903380 1 SEAL, connector
3 J930525 1 INJECTOR ASSY., fuel (Bosch), Whenever a nozzle is removed from the cylinder head, J923261 seal
5 J905153 1 SPINDLE, SEAT – nozzle pressure spring
6 J905152 1 SPRING, nozzle pressure
7 J905154 1 PLATE, STOP – nozzle valve
11 J923261 6 WASHER, SEAL – injector nozzle, 2.5 mm thick, 7 mm injector tip, Use one shim of the thickness
1 96572C4 1 LEVER, throttle control, no longer available, order 302488A1 lever on fig.3-24
2 1975823C2 1 HANDLE, KNOB – control lever
3 96576C1 1 BUSHING, LARGE, control lever
4 800-3120 1 CIRCLIP, M20, E-type, external retaining, No. 20, replaces 933355R1 E-ring
5 864-4020 1 SCREW, Hex Soc Hd, M4 x 20, 8.8
6 893-11004 1 WASHER, LOCK, Ext Tooth, M4, lock, 4 mm
7 1289365C1 1 SUPPORT, BRACKET – throttle lever
8 627-6016 2 BOLT, Hex, M6 x 16, 10.9, Full threads
9 896-11006 2 WASHER, M6 x 13 x 2, HT
10 892-11006 2 WASHER, LOCK, M6
14 1974525C1 1 BALL JOINT, throttle cable
15 95-81060 1 WASHER, 7/32″ x 9/16″ x .060″, flat, 7/32 x 9/16 x 1/16 inch
16 432-48 1 PIN, SPLIT (COTTER), 1/16″ x 1/2″
17 492-11025 1 WASHER, LOCK, 1/4″
18 425-114 1 NUT, 1/4″-28, G5
19 1289499C2 1 SUPPORT, BRACKET – coolant recovery contrainer mounting, throttle cable
22 492-11010 1 WASHER, LOCK, #10
23 225-14210 1 NUT, #10-32
26 1267688C3 1 CABLE, throttle, replaces 1267688C2 cable
27 96988C2 1 GROMMET, cable
28 A75815 1 CLAMP, retaining
29 461-31012 2 SCREW, Hex Soc Hd, #10-24 x 3/4″, BOLT – hex socket, No. 10 NC x 3/4 inch
30 492-11010 2 WASHER, LOCK, #10
31 193-1004 2 NUT, Keps, w/LW,#10-24, hex, with external tooth lock washer, No. 10 NC
32 L40315 1 SHIM, clamp
35 1808728C1 1 LEVER, throttle control
1 302488A1 1 LEVER, throttle control, replaces 220361A1 lever, On 7220 models the throttle cable mounts at hole
2 1975823C2 1 HANDLE, KNOB – control lever
3 96576C1 1 BUSHING, LARGE, control lever
4 800-3120 1 CIRCLIP, M20, E-type, external retaining, No. 20, replaces 933355R1 E-ring
5 864-4020 1 SCREW, Hex Soc Hd, M4 x 20, 8.8
6 893-11004 1 WASHER, LOCK, Ext Tooth, M4, lock, 4 mm
7 198834A1 1 SUPPORT, BRACKET – throttle lever
8 627-6016 2 BOLT, Hex, M6 x 16, 10.9, Full threads
9 896-11006 2 WASHER, M6 x 13 x 2, HT
10 892-11006 2 WASHER, LOCK, M6
14 1974525C2 1 BALL JOINT, throttle cable
15 95-81060 1 WASHER, 7/32″ x 9/16″ x .060″, flat, 7/32 x 9/16 x 1/16 inch
16 432-48 1 PIN, SPLIT (COTTER), 1/16″ x 1/2″
18 230-4714 1 NUT, LOCK, 1/4″-28, GA, hex, self-locking, 1/4 inch NF
19 224475A2 1 SUPPORT, BRACKET – throttle cable, On 7210 and 7220 models, mount item 19 bracket to the engine
20 614-10025 2 BOLT, Hex, M10 x 25, 8.8, Full Thd
21 895-15010 2 WASHER, M11 x 24 x 2
22 492-11010 1 WASHER, LOCK, #10
23 225-14210 1 NUT, #10-32
26 1267688C3 1 CABLE, throttle, replaces 1267688C2 cable, On 7220 models the throttle cable mounts at hole “A” on
27 96988C2 1 GROMMET, cable
28 A75815 1 CLAMP, retaining
29 461-31016 2 SCREW, Hex Soc Hd, #10-24 x 1″, BOLT – hex socket, No. 10 NC x 1 inch
32 L40315 1 SHIM, clamp
33 224900A1 1 PLATE, LARGE, cable clamp
1 1975959C4 1 PEDAL ASSY., foot throttle, with pad
2 434-516 1 BOLT, CARRIAGE, Short NK, 5/16″-18 x 1″, G5, Full Thd
3 425-145 1 NUT, Jam, 5/16″-18, G5, hex, jam, 5/16 inch NC
4 97043C4 1 SHAFT, throttle pedal
5 1975973C1 1 BUSHING, LARGE, left, long
6 1975974C1 1 BUSHING, LARGE, right, short
7 38-3816 1 PIN, 1/8″ x 1″, Coiled, 1/8″ x 1″, Coiled
8 1975961C2 1 LEVER ASSY., throttle pedal, prior to tractor P.I.N. JJA0064978
9 1977463C1 1 STOP, throttle pedal
10 97046C4 1 SUPPORT, throttle pedal
11 614-8020 3 BOLT, Hex, M8 x 20, 8.8
12 892-11008 3 WASHER, LOCK, M8
18 97173C3 1 CABLE, foot throttle
19 225-14210 1 NUT, #10-32
20 432-48 1 PIN, SPLIT (COTTER), 1/16″ x 1/2″
22 1344278C1 1 SUPPORT ASSY., BRACKET – cable, foot throttle, prior to tractor P.I.N. JJA0064978
23 627-6016 2 BOLT, Hex, M6 x 16, 10.9, Full threads
24 892-11006 2 WASHER, LOCK, M6
26 A75815 2 CLAMP, retaining
27 L40315 2 SHIM, clamp
28 461-31012 4 SCREW, Hex Soc Hd, #10-24 x 3/4″, BOLT – hex socket, No. 10 NC x 3/4 inch
29 492-11010 4 WASHER, LOCK, #10, Prior to tractor P.I.N. JJA0064978
30 225-14110 4 NUT, #10-24, Replaces 193-1004 nut with external tooth lock washer used on some models, prior to
30 224900A1 1 PLATE, LARGE, locking, cable clamp, not shown, see item 33 on fig. 3-24 for plate, tractor P.I.N.
37 19725R1 1 BALL JOINT, foot throttle
38 225-14210 1 NUT, #10-32
39 492-11010 1 WASHER, LOCK, #10
40 84728C1 1 JOINT, hand throttle, replaces 120319C2 ball joint, prior to tractor P.I.N. JJA0064978
40 1974525C1 1 BALL JOINT, throttle cable, tractor P.I.N. JJA0064978 and after
41 1971259C1 1 SPACER, 3/8 ID x 7/32 inch
42 495-81107 2 WASHER, .281″ x 7/8″ x .060″, flat, 9/32 x 7/8 x 3/64 inch
43 230-4714 1 NUT, LOCK, 1/4″-28, GA, hex, self-locking, 1/4 inch NF
44 97038C4 1 LEVER, throttle, replaces 97038C3 lever, prior to tractor P.I.N. JJA0064978
44 198834A1 1 SUPPORT, BRACKET – throttle lever, not shown, see item 7 on fig. 3-24 for bracket, tractor P.I.N.
46 225-14210 1 NUT, #10-32
1 255097A1 1 RESERVOIR, TANK ASSEMBLY – fuel, main, includes items 21-23 on fig.3-30 or 3-32, see note
2 1283682C1 1 TUBE, tank inlet
3 97226C1 1 O-RING, fuel inlet
4 840-1620 6 SCREW, Cross Pan Hd, M6 x 20
5 1283825C1 1 HOSE ASSY., 90 degree, inlet
6 214-1544 2 CLAMP, HOSE, #44, 2.31/3.25 Type F Worm, W/liner, adj, 2-5/16 – 3-1/4 inch dia, hose retaining
7 1283783C2 1 TUBE, filter
8 1283807C1 1 COLLAR, filler neck
9 1283826C2 1 CAP, fuel filler
10 259110A1 1 GAUGE, FUEL, SENDER – fuel level, models without auxiliary tank, see note, replaces 1987599C2
10 259111A1 1 GAUGE, FUEL, SENDER – fuel level, models with auxiliary tank, see note, replaces 103003A2 sender
17 104812C3 1 GASKET, fuel level sender
18 193-563 5 SCREW, SEMS, Hex Hd, #10-24 x 3/4″, G5, hex, with external tooth lock, No. 10 NC x 3/4 inch
19 1283890C1 1 HOSE ASSY., tank vent
20 214-1410 2 CLAMP, HOSE, #10, 0.56/1.06 Type F Worm
23 120589A1 1 SUPPORT ASSY., tank
24 614-10020 4 BOLT, Hex, M10 x 20, 8.8, Full Thd
25 825-1410 8 NUT, M10, Cl 8
26 137630C2 1 BRACKET, hold down, fuel tank
27 1287737C1 4 SCREW, BOLT – hex, 10 x 25 mm, class 10.9, special
28 1287738C2 2 WASHER, flat, 11 x 21 x 3 mm
29 120587A1 1 SUPPORT, BRACKET – upper link
32 1283792C1 1 MOUNTING CLIP, CLAMP – tube retaining
33 614-8020 2 BOLT, Hex, M8 x 20, 8.8
34 825-2408 2 NUT, M8 x 1.25, Flg, Cl 8
36 1971391C1 2 CLIP, retainer, chain
37 1971392C1 1 CHAIN (AGRICULTURE), fuel cap, 10 inch
38 A143035 1 NUT, FASTENER – stud
39 120157C1 1 CONNECTOR, fuel tank
40 536652R1 1 WASHER, flat
1 96903C3 1 RESERVOIR, TANK ASSEMBLY – fuel, main, includes items 21-23, see fig. 3-16 for mounting and
2 214-1428 2 CLAMP, HOSE, #28, 1.31/2.25 Type F Worm, Adjustable
3 130345C1 1 HOSE, 60 mm (2-3/8 inch) long, fuel tank outlet
4 130346C1 1 ADAPTER, fuel line hose to shutoff valve
5 161707C1 1 COCK, DRAIN, VALVE – fuel shutoff
6 1348241C1 1 TUBE ASSY., fuel line, at tank
7 1348264C1 4 CLAMP, HOSE, 3/8 inch, fuel supply
8 1348242C1 1 HOSE, 1700 mm (66-15/16 inch) long, fuel supply
9 1348274C1 1 CONDUIT, SLEEVE – corrugated, 17 (5/8) ID x 1575 mm (62 inch) long
10 1954474C4 1 SHIN, CLAMP – at left front cab support
12 D139225 1 FILTER, FUEL, in-line, 9.5 mm (3/8 inch) shank
13 1348239C1 1 HOSE, 78 mm (3-5/64 inch) long, filter to engine
14 217-293 1 FITTING, 90є, 3/8″ Hose x 1/4″ NPTF, Barbed, 90 degree, 3/8 barb end x 1/4 inch PT
15 A171099 2 CLAMP, HOSE, spring-type, hose
16 1348240C1 1 HOSE, 4310 mm (169-11/16 inch) long, fuel return to tank
17 1348275C1 1 LOOM, SLEEVE – corrugated, 17 (5/8) ID x 4064 mm (160 inch) long, fuel return
18 1987599C2 1 GAUGE, FUEL, SENSOR – fuel level, main tank, models without auxiliary tank, replaces 1987599C1
19 193-563 5 SCREW, SEMS, Hex Hd, #10-24 x 3/4″, G5, hex, with external tooth lock, No.10 NC x 3/4 inch
20 104812C3 1 GASKET, fuel level sender
21 238-5210 1 O-RING, -210, 70 Duro, .734″ ID x .139″ Thk
22 1251790C1 1 FITTING, ADAPTER – straight, fuel tank drain
23 1251791C1 1 NUT, hex, jam, special
24 104465C1 1 VALVE, DRAIN, main fuel tank
25 104896C1 1 TUBE, fuel tank drain, 457 mm (18 inch) long, cut from 74813C1 bulk tube, see below
1 255097A1 1 RESERVOIR, TANK ASSEMBLY – fuel, main, includes items 21-23, see fig. 3-28 for mounting and
2 214-1428 2 CLAMP, HOSE, #28, 1.31/2.25 Type F Worm, Adjustable
3 130345C1 1 HOSE, 60 mm (2-3/8 inch) long, fuel tank outlet
4 196250A1 1 ADAPTER, fuel line hose to shutoff valve
5 196465A1 1 COCK, DRAIN, VALVE – fuel shutoff
6 196262A1 1 PIPE, TUBE – fuel line, at tank
7 196252A1 4 CLAMP, fuel supply
8 196251A1 1 HOSE, 13 (1/2) x 20 (25/32) x 1700 mm (x 66-15/16 inch) long, fuel supply
9 196249A1 1 CONDUIT, SLEEVE – corrugated, 27 (1-1/16) ID x 1000 mm (39-3/8 inch) long, cut from 291260A2
10 1954474C4 1 SHIN, CLAMP – at left front cab support
12 194199A1 1 FILTER, STRAINER, fuel, in-line, 12.7 mm (1/2 inch) shank
13 196247A1 1 HOSE, 13 (1/2) x 20 (25/32) x 78 mm (3-5/64 inch) long, filter to engine
14 217-290 1 FITTING, 90є, 1/2″ Hose x 3/8″ NPTF, Barbed, 90 degree, 1/2 barb end x 3/8 inch PT
15 A171099 6 CLAMP, HOSE, spring-type, hose
16 196266A2 1 HOSE, 8 (21/64) x 15 (5/8) x 3750 mm (147-5/8 inch) long, fuel return to tank
17 196245A2 1 LOOM, SLEEVE – corrugated, 17 (5/8) ID x 3700 mm (145-11/16 inch) long, fuel return
18 259110A1 1 GAUGE, FUEL, SENDER – fuel level, main tank, models without auxiliary tanks, replaces 1987599C2
19 193-563 5 SCREW, SEMS, Hex Hd, #10-24 x 3/4″, G5, hex, with external tooth, No. 10 NC x 3/4 inch
20 104812C3 1 GASKET, fuel level sender
21 238-5210 1 O-RING, -210, 70 Duro, .734″ ID x .139″ Thk
22 1251790C1 1 FITTING, ADAPTER – straight, fuel tank drain
23 1251791C1 1 NUT, hex, jam, special
24 104465C1 1 VALVE, DRAIN, main fuel tank
25 104896C1 1 TUBE, fuel tank drain, 457 mm (18 inch) long, cut from 74813C1 bulk tube
26 195509A1 1 COUPLING, CONNECTOR – 5/16 inch hose
27 225005A1 1 HOSE, 8 (21/64) x 15 (5/8) x 1650 mm x (65 inch) long, fuel cooler to main tank
28 225006A1 1 LOOM, SLEEVE – corrugated, 17 (5/8) ID x 1600 mm (63 inch) long
30 196248A1 1 LOOM, SLEEVE – corrugated, 27 (1-1/6) ID x 560 mm (22-3/64 inch) long, cut from 291260A2 bulk
31 195509A1 1 COUPLING, CONNECTOR – at fuel injection pump
32 196263A1 1 HOSE, 8 (21/64) x 15 (5/8) x 1800 mm (70-7/8 inch) long, fuel injection pump to fuel cooler, engine
33 196246A1 1 CONDUIT, SLEEVE – corrugated, 17 (5/8) ID x 1650 mm (65 inch) long, cut from 291262A2 bulk
34 362123R1 1 CLIP, hose
1 137700C6 1 RESERVOIR, TANK ASSEMBLY – fuel, auxiliary, also order Ref 4
2 97013C1 1 HOSE ASSY., tank, auxiliary
3 214-1428 2 CLAMP, HOSE, #28, 1.31/2.25 Type F Worm, Adjustable
4 104812C3 1 GASKET, fuel level sender
5 103002A2 1 GAUGE, FUEL, SENSOR – auxiliary fuel tank level, also order Ref 4, no longer available, order
5 193855A2 1 GAUGE, FUEL, SENSOR – auxiliary fuel tank level, replaces 103002A2 sensor
6 193-563 5 SCREW, SEMS, Hex Hd, #10-24 x 3/4″, G5, hex, with external tooth lock, No. 10 NC x 3/4 inch
7 137702C5 1 SUPPORT ASSY., tank
8 614-12025 3 BOLT, Hex, M12 x 25, 8.8
12 1280992C2 1 SUPPORT ASSY., tank, rear
13 614-10025 2 BOLT, Hex, M10 x 25, 8.8, Full Thd
14 892-11010 2 WASHER, LOCK, M10
15 825-1410 2 NUT, M10, Cl 8
16 813-16140 1 BOLT, Hex, M16 x 140, 8.8, BOLT – hex, 16 – 2.0 x 140 mm
17 137704C1 1 SUPPORT, front, tank
20 144252C2 1 STIFFENER, BRACKET – hold down, tank
21 1259898C1 1 BRACKET, retaining, tank
22 614-10020 2 BOLT, Hex, M10 x 20, 8.8, Full Thd
23 825-1410 2 NUT, M10, Cl 8
24 1259899C1 1 SPACER, support, front
25 814-10040 1 BOLT, Hex, M10 x 40, 8.8, Full Thd
26 144253C1 1 SPACER, support, rear
27 814-10045 1 BOLT, Hex, M10 x 45, 8.8
30 1251937C1 1 REINFORCEMENT, CHANNEL – reinforcement brace, tank
31 217-270 1 VALVE LOCK, shutoff, brass, 3/8 x 3/8 inch
32 1348237C1 1 TUBE, fuel supply
33 217-103 1 COCK, DRAIN, VALVE – 1/4 inch PT, drain
34 1348238C1 1 HOSE, 1080 mm (41-1/2 inch) long, fuel supply
35 217-293 1 FITTING, 90є, 3/8″ Hose x 1/4″ NPTF, Barbed, 90 degree, 3/8 barb end x 1/4 inch PT
38 1348236C1 1 HOSE, 2431 mm (95-3/4 inch) long, fuel return
39 1348277C1 1 LOOM, SLEEVE – corrugated, 17 (5/8) ID x 2331 mm (91-13/16 inch) long
42 A171099 2 CLAMP, HOSE, spring-type, hose, retaining
44 1954474C4 1 SHIN, CLAMP – fuel line, at left front cab support
47 306132C1 2 STRAP, CABLE, .30″ x 14.5″, tie, 14 inch long, nylon
50 1348264C1 4 CLAMP, HOSE, hose, 3/8 inch
51 D139225 1 FILTER, FUEL, in-line
53 1348276C1 1 LOOM, SLEEVE – corrugated, 17 (5/8) ID x 980 mm (38-19/32 inch) long
54 1348239C1 1 HOSE, 78 mm (3-5/64 inch) long, fitting to fuel sender
55 103010A1 1 HOSE, 1970 mm (77-9/16 inch) long, vent, auxiliary tank
56 103011A1 1 CONDUIT, SLEEVE – corrugated, 17 (5/8) ID x 1841 mm (72-1/2 inch) long, cut from 291262A2 bulk
57 A171099 2 CLAMP, HOSE, spring-type, retaining
59 238-5210 1 O-RING, -210, 70 Duro, .734″ ID x .139″ Thk
60 1251790C1 1 FITTING, ADAPTER – straight, fuel tank drain
61 1251791C1 1 NUT, hex, jam, special
62 193-1000 1 NUT, Keps, w/LW,#10-32, hex, with external tooth lock washer, No. 10 NF, harness electrical lead to
1 137700C6 1 RESERVOIR, TANK ASSEMBLY – fuel, auxiliary, standard capacity
2 1251790C1 1 FITTING, ADAPTER – straight, fuel tank drain
3 238-5210 1 O-RING, -210, 70 Duro, .734″ ID x .139″ Thk
4 1251791C1 1 NUT, hex, jam, special
5 217-103 1 COCK, DRAIN, VALVE – 1/4 inch PT
17 137702C5 1 SUPPORT ASSY., tank
18 614-12025 4 BOLT, Hex, M12 x 25, 8.8, Front support and tank support
19 1280992C2 1 SUPPORT ASSY., tank, rear
20 137704C2 1 SUPPORT ASSY., tank, front
21 614-12025 1 BOLT, Hex, M12 x 25, 8.8
22 9804279 2 NUT, M12 x 1.75, Flg, Cl 8
23 1259898C1 1 BRACKET, retaining, tank
24 144252C2 1 STIFFENER, BRACKET – hold down, tank
25 1251937C1 1 REINFORCEMENT, CHANNEL – reinforcement brace, tank
26 614-10020 2 BOLT, Hex, M10 x 20, 8.8, Full Thd
27 825-1410 2 NUT, M10, Cl 8
28 1259899C1 1 SPACER, support, front
29 814-10040 1 BOLT, Hex, M10 x 40, 8.8, Full Thd
30 144253C1 1 SPACER, support, rear
31 814-10045 1 BOLT, Hex, M10 x 45, 8.8
32 97013C1 1 HOSE ASSY., tank, auxiliary
33 214-1428 2 CLAMP, HOSE, #28, 1.31/2.25 Type F Worm, Adjustable
34 193855A2 1 GAUGE, FUEL, SENSOR – auxiliary fuel tank level
35 104812C3 1 GASKET, fuel level sender
36 1978426C1 5 SCREW, pan Phillips, with O-ring, No. 10 – 24 x 3/4 inch
37 196265A1 1 HOSE, 8 (21/64) x 15 (5/8) x 3530 mm (139 inch) long, fuel return, fuel cooler to auxiliary tank
38 196244A1 1 LOOM, SLEEVE – corrugated, 17 (5/8) ID x 3480 mm (137 inch) long
39 A171099 2 CLAMP, HOSE, spring-type, hose, retaining
40 103010A1 1 HOSE, 1970 mm (77-9/16 inch) long, vent, auxiliary tank
41 103011A1 1 CONDUIT, SLEEVE – corrugated, 17 (5/8) ID x 1841 mm (72-1/2 inch) long, cut from 291262A2 bulk
42 A171099 2 CLAMP, HOSE, spring-type, retaining
43 196465A1 1 COCK, DRAIN, VALVE – fuel shutoff, supply, brass
44 196458A1 1 TUBE, CONNECTOR – barb, 1/2 barb x 1/2 inch female pipe
45 196267A1 1 HOSE, 13 (1/2) x 20 (25/32) x 1235 mm (48-5/8 inch) long, fuel supply, auxiliary tank to in-line filter
46 196248A1 1 LOOM, SLEEVE – corrugated, 27 (1-1/6) ID x 560 mm (22-3/64 inch) long, cut from 291260A2 bulk
47 196252A1 1 CLAMP, hose at supply valve connector
48 194199A1 1 FILTER, STRAINER, fuel, in-line
49 196247A1 1 HOSE, 13 (1/2) x 20 (25/32) x 78 mm (3-5/64 inch) long, fuel filter to lift pump
50 196252A1 3 CLAMP, at in-line fuel filter
51 197095A1 1 ELBOW, 90 degree, 1/2 barb end x 1/2 inch PT, 7220 Tractors
51 217-290 1 FITTING, 90є, 1/2″ Hose x 3/8″ NPTF, Barbed, 90 degree, 1/2 barb end x 3/8 inch PT, 7210 Tractors
52 217-1012 1 ADAPTER, 1/4″-18 Male NPTF x 3/8″-18 Female NPTF, ADAPTER – straight, 1/4 PT x 3/8 inch female
53 196263A1 1 HOSE, 8 (21/64) x 15 (5/8) x 1800 mm (70-7/8 inch) long, fuel injection pump to fuel cooler, engine
53 235337A1 1 HOSE, 8 (21/64) x 15 (5/8) x 1345 mm (53 inch) long, fuel injection pump to fuel cooler, engine serial
54 196246A1 1 CONDUIT, SLEEVE – corrugated, 17 (5/8) ID x 1650 mm (65 inch) long, cut from 291262A2 bulk
55 A171099 3 CLAMP, HOSE, spring-type, hose
56 195509A1 1 COUPLING, CONNECTOR – barbed, 5/16 inch hose
57 362123R1 1 CLIP, hose
58 1954474C4 1 SHIN, CLAMP – fuel line, at left front cab support, return and supply lines
59 193-1000 1 NUT, Keps, w/LW,#10-32, hex, with external tooth lock washer, No.10 NF, harness electrical lead to
60 813-16140 1 BOLT, Hex, M16 x 140, 8.8, BOLT – hex, 16 – 2.0 x 140 mm
62 306132C1 2 STRAP, CABLE, .30″ x 14.5″, tie, 14 inch long, nylon
1 122661A1 1 HARNESS, cab, lower, without connection for electrically operated PTO valve and switch, prior to
2 A177090 1 HARNESS, monitor, implement
3 1964859C6 1 CLUSTER, ASSEMBLY – instrument, new, parts list fig. 4-20
6 92365C1 2 SWITCH, horn and ether start
7 D134737 1 SWITCH, IGNITION, SWITCH ASSEMBLY – ignition, includes keys
8 1964785C1 1 NUT, hex special, black
9 A77313 1 SET OF 2 KEYS, Metal Without Padding
10 1964785C1 1 NUT, mounting, ignition switch
11 1964831C1 1 SET OF 2 KEYS, ignition, coated, if used
12 122860A1 1 NUT, switch
13 515-25254 1 CLAMP, 1″, Insul, 1/2″ Bolt, P-type, Harness
14 123014A1 2 SWITCH, brake, differential lock
15 92345C1 1 SWITCH, override shutdown (Includes Ref 48), without description or symbol on switch, if used, may
16 468647C2 1 BLOCK ASSY., junction, replaces 468647C1 block, see fig. 4-24 for mounting hardware
17 1964561C1 1 BAR, junction block buss, see page 4-25 for mounting hardware
19 1964773C1 1 LIGHTER, CIGARETTE, 12 volt, small knob, if used
20 A177447 1 LIGHTER, CIGARETTE, ELEMENT – pop-out unit, small knob
19 245576C1 1 LIGHTER, CIGARETTE, ASSEMBLY – 12 volt, large knob, if used
20 378781R1 1 LIGHTER, CIGARETTE, ELEMENT – pop up, lighter, large knob
23 92346C1 1 SWITCH, differential lock (Includes Ref 48)
24 91921C1 1 SWITCH, lighting
25 97107C3 1 BUTTON, KNOB – light switch
27 129130A1 1 SWITCH, MFD (Includes Ref 48)
28 245918C1 1 CAP, PLUG – rectangular, if used
29 92344C1 1 SWITCH, ASSEMBLY – high/low (Includes Ref 48)
30 1987422C1 1 SWITCH, and flasher
31 131-428 1 NUT, LOCK, PAL, 3/4″-20, hex, self-locking, 3/4-20 inch, 3/4-20
34 97102C1 1 ADAPTER, lever, turn signal
35 170-104 1 SCREW, Sltd Pan Hd, #5-40 x 3/8″, machine, pan head Phillips, No. 5 NC x 3/8 inch
36 1329896C1 1 CLASP, CLIP – retaining, lever
37 97103C3 1 LEVER, turn signal
38 1334638C1 1 SPACER, electrical, if used, see fig. 9-16 for spacer at tool box
39 814-16150 1 BOLT, Hex, M16 x 150, 8.8, BOLT – hex, 16 – 2.0 x 150 mm
40 893-16016 1 WASHER, LOCK, Int Tooth, M16, internal tooth lock, 16 mm
41 825-1416 1 NUT, M16, Cl 8
42 92043C3 1 SWITCH, drive, creeper, replaces 92043C2 switch
44 96890C2 1 BRACKET, creeper switch
45 1983363C2 1 LAMP, LIGHT ASSEMBLY – cluster
46 F64363 1 BULB, lamp, replaces 28791R1 bulb
47 104389C1 1 CLIP, retaining, light
48 3141107R1 4 BULB, W5/1.2, 12V, 1.2W, 2 watt
49 459330C1 2 WASHER, LOCK, lock, No. 24
50 459329C1 2 NUT, hex, No. 24
51 137430A1 1 SWITCH, ASSEMBLY – override shutdown (Includes Ref 48), with shutdown override description on
54 189574A2 1 SWITCH, IGNITION, toggle, PTO, if used
55 896-15012 1 WASHER, M12 x 28.5 x 4, HT, flat, 13.5 x 28 x 4 mm, hardened
56 223565A1 1 KNOB,BALL, control, PTO switch
57 183696A1 1 INDICATOR, LAMP – green, PTO
58 225164C1 1 CONNECTOR, ELEC, electrical, type GH, implement receptacle, female
59 225168C1 3 TERMINAL CONNECTOR, electrical, female, 14-16 ga., type THI, not shown
60 187103A1 1 CONNECTOR, ELEC, auxiliary power, assembly
61 225165C1 1 CONNECTOR, ELEC, electrical, type GQ, male, Part of the Harness Repair Kit P/N 1714005
62 225153C1 1 CONNECTOR, ELEC, CONNECTOR – electrical, type GX, strain relief clamp, Part of the Harness
63 225166C1 3 PIN, ELECT TERMINAL, electrical male blade, 14-16 ga., type TJ1, not shown, Part of the Harness
65 245485C1 1 CONNECTOR, ELEC, receptacle, type DK, female, implement plug auxiliary power source, not shown
1 1983257C1 1 HARNESS, engine and front component
3 A187728 1 MOTOR, STARTER, ASSEMBLY – engine, parts list fig. 4-30
4 91448C2 1 ALTERNATOR, ASSEMBLY – engine, 110 ampere, parts list Fig. 4-34
5 515-23127 1 CLAMP, 1/2″, Insul, 3/8″ Bolt, P-type, 1/2 inch ID, closed, used prior to P.I.N. JJA0058861
6 515-2348 1 CLAMP, 3/16″, Insul, 3/8″ Bolt, P-type, 10.3 mm ID
7 515-22127 4 CLAMP, 1/2″, Insul, 5/16″ Bolt, P-type, Closed
9 R54362 1 CLAMP, J, 9/16″ Insul, 5/16″ Bolt, harness, open, 12.7 mm ID
10 L18337 3 STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch, nylon
14 1987588C1 1 SENSOR, exhaust gas temperature
15 1999755C2 1 COMPRESSOR, ASSEMBLY – air conditioning, component parts not serviced separately
17 A176566 1 TRANSMITTER, SENDER – coolant temperature
18 193-1000 1 NUT, Keps, w/LW,#10-32, hex, with external tooth lock washer, No. 10 NF
23 1546461C2 1 SWITCH, oil pressure, 10 psi, replaces 1546461C1 switch
25 232948A1 1 SWITCH, PRESSURE, high, 400 psi, air conditioning
30 413-516 1 BOLT, Hex, 5/16″-18 x 1″, G5, Full Thd, hex, 5/16 NC x 1 inch, if used
31 425-105 1 NUT, 5/16″-18, G5, If Used
32 493-81008 1 WASHER, LOCK, Int Tooth, 5/16″, internal tooth, 5/16 inch, if used
35 166166R1 1 HORN, 12 volt, low note, tractor, replaces 411949C91 horn
36 279476A1 1 SENSOR, low coolant, coolant level
44 1983640C1 1 SWITCH, SWITCH – restriction, air cleaner
45 362667R1 1 CLIP, CLAMP – retainer, exhaust gas temperature to turbo elbow bracket
46 614-10020 1 BOLT, Hex, M10 x 20, 8.8, Full Thd, Ground front harness to engine block, if used
47 892-11010 1 WASHER, LOCK, M10, If used
48 281-34812 1 SCREW, SELF TAPPING, Hex Hd, 5/16″ x 3/4″, self-tapping, hex washer head, 5/16 NC x 3/4 inch, if
1 226666A1 1 HARNESS, engine and front component
3 A187728 1 MOTOR, STARTER, ASSEMBLY – engine, parts list fig. 4-30
4 91448C2 1 ALTERNATOR, ASSEMBLY – engine, 110 ampere, parts list fig. 4-34
6 515-2348 1 CLAMP, 3/16″, Insul, 3/8″ Bolt, P-type, 10.3 mm ID
7 515-22127 4 CLAMP, 1/2″, Insul, 5/16″ Bolt, P-type, Closed
9 R54362 1 CLAMP, J, 9/16″ Insul, 5/16″ Bolt, harness, open, 12.7 mm ID
10 L18337 3 STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch, nylon
14 1987588C1 1 SENSOR, exhaust gas temperature
15 1999755C2 1 COMPRESSOR, ASSEMBLY – air conditioning, component parts not serviced separately
17 A176566 1 TRANSMITTER, SENDER – coolant temperature
18 193-1000 1 NUT, Keps, w/LW,#10-32, hex, with external tooth lock washer, No. 10 NF
23 1546461C2 1 SWITCH, oil pressure, 10 psi, replaces 1546461C1 switch
25 232948A1 1 SWITCH, PRESSURE, high, 400 psi, air conditioning
35 166166R1 1 HORN, 12 volt, low note, tractor, replaces 411949C91 horn
36 279476A1 1 SENSOR, low coolant, coolant level
44 1983640C1 1 SWITCH, SWITCH – restriction, air cleaner
45 362667R1 1 CLIP, CLAMP – retainer, exhaust gas temperature to turbo elbow bracket
46 614-10016 1 BOLT, Hex, M10 x 16, 8.8, Full Thd, Ground Front Harness to Engine Block, If Used
47 895-11010 1 WASHER, M10 x 20 x 2, If used
48 281-34812 1 SCREW, SELF TAPPING, Hex Hd, 5/16″ x 3/4″, self-tapping, hex washer head, 5/16 NC x 3/4 inch
1 1987426C2 1 HARNESS, transmission speed and range, without electrically operated PTO, prior to tractor P.I.N.
16 1983218C2 1 SWITCH, neutral start, see fig. 6-30
17 238-5014 1 O-RING, -014, 70 Duro, .489″ ID x .070″ Thk
18 A176566 1 TRANSMITTER, SENDER – transmission oil temperature
19 193-1000 1 NUT, Keps, w/LW,#10-32, hex, with external tooth lock washer, No. 10 NF
20 1546462C1 1 SENSOR, lube oil pressure
21 244451A1 1 SWITCH, PRESSURE, transmission system pressure, mounts to PTO valve on fig. 8-6, replaces
Pages: 1 2 3 4 5

Leave a Reply

Your email address will not be published. Required fields are marked *