7220 CASE IH Magnum Tractor (North America)
7220 CASE IH Magnum Tractor (North America) — parts list, part 2 of 5
Assemblies on this page: Parts list (continued) … Parts list (continued).
Parts list (continued)
| Pos | Part no. | Qty | Description |
|---|---|---|---|
| 22 | A186005 | 1 | SENSOR, tractor speed |
| 23 | 238-5115 | 2 | O-RING, -115, 70 Duro, .674″ ID x .103″ Thk |
| 24 | 103002A2 | 1 | GAUGE, FUEL, SENSOR – auxiliary fuel tank level, replaces 103002A1 sensor, prior to tractor P.I.N. |
| 24 | 193855A2 | 1 | GAUGE, FUEL, SENSOR – auxiliary fuel tank level (not shown), tractor P.I.N. JJA0064978 and after |
| 25 | 92261C1 | 1 | HARNESS, sender, auxiliary fuel level |
| 28 | 1958159C2 | 1 | VALVE, SOLENOID, ASSEMBLY – drive, creeper |
| 29 | 1272538C1 | 1 | VALVE, ASSEMBLY – solenoid, MFD, parts list fig. 8-16 |
| 30 | 1957801C1 | 1 | SWITCH, PRESSURE, pressure, hydraulic filter |
| 31 | A186004 | 1 | SENSOR, engine rpm |
| 35 | 1964698C3 | 1 | SWITCH, PTO neutral, if used, used prior to tractor P.I.N. JJA0064978 |
| 41 | 1546463C1 | 1 | PRESSURE SWITCH, flow compensated (PFC) |
| 42 | 221545A1 | 1 | SWITCH, KIT – implement status switch, includes lift switch and associated parts, plus instructions, as |
| 43 | 221546A1 | 1 | HARNESS, extension, 30 foot, used with 221545A1 implement status switch kit on models with trailing |
| 33 | 237-6005 | 1 | O-RING, 5-1, 90 Duro, .414″ ID x .072″ Thk |
| 1 | 1964584C1 | 1 | HARNESS, fender |
| 2 | 121645C1 | 1 | SOCKET/RECEPTACLE, covered, 7 pin |
| 3 | 481849C1 | 1 | COVER, PROTECTIVE, BOOT – wiring harness |
| 4 | 92261C1 | 1 | HARNESS, sender, auxiliary fuel level, used with auxiliary tank |
| 7 | 1546476C1 | 2 | LAMP, ASSEMBLY – tail, not available for service, see fig. 4-36 for components |
| 10 | 102590A1 | 1 | SUPPORT ASSY., auxiliary outlet |
| 11 | 1287737C1 | 2 | SCREW, BOLT – hex, 10 x 25 mm class 10.9, support |
| 12 | 825-1410 | 2 | NUT, M10, Cl 8 |
| 13 | 614-8020 | 2 | BOLT, Hex, M8 x 20, 8.8 |
| 14 | 825-2408 | 2 | NUT, M8 x 1.25, Flg, Cl 8 |
| 15 | 362123R1 | 6 | CLIP, harness retaining |
| 16 | 97212C1 | 4 | SCREW, pan head, No. 6-20 x 7/8 inch |
| 17 | 895-11008 | 2 | WASHER, M8 x 16 x 1.6 |
| 18 | 121646C1 | 1 | CONNECTOR, male, 7 pin, if used |
| 1 | 1964559C2 | 1 | HARNESS, headliner, no longer available, order 140646A1 harness and 136893A1 door dome lamp |
| 2 | 92185C1 | 2 | LIGHT ASSY., LAMP ASSEMBLY – warning, flasher, parts list fig. 4-36 |
| 3 | 83882C91 | 1 | LAMP, ASSEMBLY – console illumination, parts list fig. 4-40 |
| 4 | 1983391C1 | 1 | LAMP, dome, parts list fig. 4-40 |
| 5 | 92269C1 | 2 | LAMP, WORK, ASSEMBLY – flood, parts list fig. 4-40 |
| 6 | 122579A1 | 1 | SWITCH, PRESSURE, low pressure, air conditioning |
| 7 | A186256 | 1 | WIPER MOTOR, 12 volt, windshield |
| 11 | 1977350C1 | 1 | COVER, switch, door |
| 12 | 245175C1 | 1 | SWITCH, door, dome lamp, with bent blade terminal, if used |
| 13 | 92115C2 | 1 | SWITCH, wiper, windshield |
| 14 | 92100C2 | 1 | SWITCH, blower |
| 15 | 92101C1 | 1 | SWITCH, thermostat |
| 16 | 1964672C1 | 1 | LIGHT, indicator, amber, 14 volt, air conditioning shut down |
| 17 | F93209 | 1 | WIPER MOTOR, ASSEMBLY – rear, parts list fig. 4-48 |
| 22 | 22-824 | 2 | STRAP, CABLE, 3/16″ x 7 1/4″ |
| 23 | 97249C1 | 2 | CLIP, CLAMP – harness |
| 24 | 104033C2 | 2 | SCREW, SELF TAPPING, Cross Wash Hd, M4.8 x 19, Coated, self-tapping, truss head, No. 10-16 x |
| 27 | 97039C1 | 1 | GROMMET, windshield upper channel |
| 1 | 1987421C1 | 1 | HARNESS, rear, headliner |
| 2 | 92185C1 | 2 | LIGHT ASSY., LAMP – warning, flasher, parts list fig. 4-36 |
| 3 | 1977564C2 | 1 | BLOWER, cab, component parts not serviced separately |
| 4 | 1343938C2 | 1 | RESISTOR, blower, replaces 1343938C1 resistor |
| 7 | 97006C1 | 4 | BOLT, BOLT – hex flange, special, 6 – 1 x 20 mm, self-locking, 6 x 20 mm |
| 8 | 97005C1 | 4 | NUT, hex flange, self-locking, special, 6 mm – 1 |
| 10 | 97032C5 | 1 | SUPPORT, blower |
| 11 | 231-5144 | 10 | NUT, Flg, USR, 1/4″-20 |
| 12 | 117975 | 1 | GROMMET, 5/8″ ID x 1 3/8″ x .062″, Diag Cut, rubber, for 5/8 inch diameter hole |
| 13 | 362123R1 | 3 | CLIP |
| 1 | 113663A1 | 1 | SWITCH, transport, field, momentary hitch raise/lower |
| 2 | A186061 | 1 | POTENTIOMETER, electrical, gauge, hitch, load, See Fig. 8-26 for mounting |
| 3 | A186061 | 1 | POTENTIOMETER, electrical, gauge, sensitivity, travel, See Fig. 8-26 for mounting |
| 4 | 1983394C2 | 1 | RELAY, mini, 12 volt, replaces 146461C1 relay |
| 6 | 781991C1 | 1 | BULB, C2F, #182, 14.4V, lamp, hitch indicator |
| 7 | 96998C1 | 1 | LENS, indicator lamp, amber |
| 14 | 235010A1 | 1 | PANEL, secondary control, replaces 123473A1 panel, See Fig. 8-26 for mounting |
| 18 | 122874A1 | 1 | HARNESS, hitch control, console |
| 20 | 490691C1 | 1 | WASHER, lock |
| 21 | 490692C1 | 1 | NUT, hex, 1-1/2 inch |
| 22 | 305523A1 | 1 | UNIT, MODULE – hitch, new, replaces 232835A2 and 112889A1 modules |
| 23 | 896-11006 | 2 | WASHER, M6 x 13 x 2, HT |
| 24 | 825-1406 | 2 | NUT, M6, Cl 8 |
| 26 | 133738A1 | 2 | CLIP, CLAMP – P-type |
| 27 | 22-611 | 1 | CLIP, ELECTRICAL, CLAMP – harness |
| 28 | 413-510 | 2 | BOLT, Hex, 5/16″-18 x 5/8″, G5, Full Thd |
| 29 | 413-68 | 1 | BOLT, Hex, 3/8″-16 x 1/2″, G5, Full Thd |
| 32 | 92949C5 | 1 | VALVE, ASSEMBLY – hitch control, parts list fig 8-40 |
| 33 | 114255A2 | 2 | POTENTIOMETER, GAUGE – position |
| 34 | 515-23127 | 1 | CLAMP, 1/2″, Insul, 3/8″ Bolt, P-type, 1/2 inch ID, replaces 49838 clamp |
| 35 | 614-8016 | 3 | BOLT, Hex, M8 x 16, 8.8 |
| 36 | 892-11008 | 1 | WASHER, LOCK, M8 |
| 37 | 1348212C1 | 1 | SHAFT, potentiometer sensor, see fig. 9-2 for housing |
| 38 | A164914 | 2 | BUSHING, sensor |
| 39 | A162622 | 1 | COUPLING, FLEXIBLE |
| 40 | 238-5012 | 1 | O-RING, -012, 70 Duro, .364″ ID x .070″ Thk |
| 41 | 100-3350 | 1 | RING, LOCKING, #50, .392″ Dia, E-Type, (Replaces 24075T1) |
| 42 | 1960765C2 | 2 | GROMMET, harness |
| 43 | 1348057C1 | 2 | TUBE, harness |
| 49 | 614-10020 | 2 | BOLT, Hex, M10 x 20, 8.8, Full Thd |
| 50 | 895-18010 | 2 | WASHER, M10 x 18 x 1.6, If used |
| 51 | 1983255C2 | 1 | HARNESS, hitch control, rear chassis |
| 55 | 1964916C3 | 2 | PIN, LARGE, lower link, hitch sensing |
| 56 | 205-61 | 1 | BUTTON, HOLE PLUG, 1 1/2″, button, 1-1/2 inch, without hitch |
| 3 | A48889 | 1 | SUPPORT, SOCKET – bulb |
| 4 | A48888 | 1 | BULB, lamp, instrument |
| 8 | 1971376C1 | 4 | SCREW, SELF TAPPING, Cross Pan Hd, #10 x 1″, self-tapping, pan Phillips, No. 10-16 x 1 inch |
| 1 | 1964622C3 | 1 | PLATE ASSY., mounting |
| 2 | 825-1406 | 7 | NUT, M6, Cl 8 |
| 4 | 225-14110 | 4 | NUT, #10-24 |
| 5 | 495-31022 | 4 | WASHER, #10 |
| 12 | A39079 | 1 | SOLENOID, magnetic relay, starter, ignition, no longer available, order 178149A1 kit, see items 34-40 |
| 17 | 896-11006 | 2 | WASHER, M6 x 13 x 2, HT |
| 19 | 825-1406 | 2 | NUT, M6, Cl 8 |
| 22 | 107655C1 | 1 | SWITCH, SOLENOID, SWITCH – magnetic, cab solenoid, power |
| 23 | 614-6025 | 2 | BOLT, Hex, M6 x 25, 8.8, BOLT – hex, full threads, 6 – 1.0 x 25 mm |
| 24 | 829-1306 | 2 | NUT, M6, Cl 10 |
| 25 | 91954C1 | 1 | SUPPORT, BRACKET – mounting, circuit breaker |
| 28 | 495-11028 | 2 | WASHER, 1/4″, SAE, flat, 9/32 x 5/8 x 1/16 inch |
| 29 | 492-11025 | 2 | WASHER, LOCK, 1/4″ |
| 30 | 425-104 | 2 | NUT, 1/4″-20, G5 |
| 31 | 245761C1 | 1 | CIRCUIT BREAKER, 10 ampere |
| 31 | 245762C1 | 1 | CIRCUIT BREAKER, 15 ampere |
| 31 | 245763C1 | 2 | CIRCUIT BREAKER, 20 ampere |
| 31 | 245765C1 | 4 | CIRCUIT BREAKER, 30 ampere |
| 32 | 245861C1 | 1 | BAR, breaker bus |
| 33 | 245862C1 | 1 | BAR, buss, 4 hole |
| 34 | 178148A1 | 1 | COVER, solenoid switch |
| 35 | 183038A1 | 1 | SWITCH, SOLENOID, SWITCH – solenoid with cover, ignition, no longer available, order 178149A1 |
| 36 | 492-11010 | 1 | WASHER, LOCK, #10 |
| 37 | 225-14210 | 1 | NUT, #10-32 |
| 38 | 492-11031 | 2 | WASHER, LOCK, 5/16″, If used, may be replaced by item 41 |
| 39 | 425-105 | 2 | NUT, 5/16″-18, G5, If used, may be replaced by item 41 |
| 40 | L18337 | 2 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch |
| 41 | 231-5145 | 2 | NUT, Flg, USR, 5/16″-18, Replaces lock washer and nut, items 38 and 39, used on some models |
| 1 | 468647C2 | 1 | BLOCK ASSY., junction, power and ground, replaces 468647C1 block |
| 2 | 1964561C1 | 1 | BAR, junction block buss |
| 3 | 413-416 | 2 | BOLT, Hex, 1/4″-20 x 1″, G5 |
| 4 | 492-11025 | 2 | WASHER, LOCK, 1/4″ |
| 5 | 425-104 | 2 | NUT, 1/4″-20, G5 |
| 8 | 614-6020 | 2 | BOLT, Hex, M6 x 20, 8.8, Full threads |
| 9 | 896-11006 | 2 | WASHER, M6 x 13 x 2, HT |
| 10 | 892-11006 | 2 | WASHER, LOCK, M6 |
| 11 | 829-1306 | 2 | NUT, M6, Cl 10 |
| 12 | 895-18010 | 1 | WASHER, M10 x 18 x 1.6 |
| 13 | 492-11038 | 1 | WASHER, LOCK, 3/8″ |
| 14 | 425-146 | 2 | NUT, Jam, 3/8″-16, G5, hex, jam, 3/8 inch NC |
| 1 | 1955202C1 | 1 | ELECTRICAL CABINET, BOX – battery |
| 2 | 96867C2 | 1 | SPACER, upper, box mounting |
| 3 | 96868C2 | 1 | SPACER, lower, box mounting |
| 4 | 814-10060 | 2 | BOLT, Hex, M10 x 60, 8.8, Battery box to transmission control valve |
| 5 | 96636C1 | 1 | SUPPORT, box, rear, if used |
| 6 | 813-16060 | 2 | BOLT, Hex, M16 x 60, 8.8, Full Thd, Bolt, Hex, M16 x 60, 8.8, Full Thd, if used |
| 7 | 896-11016 | 2 | WASHER, M17.5 x 30 x 4, HT, If Used |
| 8 | 895-11012 | 2 | WASHER, M12 x 24 x 2.5, flat, 13.5 x 24 x 2.5 mm |
| 9 | 829-1412 | 2 | NUT, M12, Cl 10 |
| 12 | 96656C1 | 1 | COVER, battery, top |
| 15 | 96657C2 | 1 | COVER, battery box, front |
| 17 | 1334657C1 | 1 | PLATE, LARGE, cover (See Note) |
| 18 | 1960750C1 | 6 | SCREW, special, 1/4 NC x 3/8 inch |
| 19 | 231-5144 | 6 | NUT, Flg, USR, 1/4″-20 |
| 22 | BMF31G | 2 | BATTERY, DRY, 12V, Electrical supply |
| 23 | 96635C1 | 2 | ANGLE, BRACKET – hold down, battery |
| 24 | 97052C1 | 4 | TRUSS ROD, BOLT – hold down, battery |
| 25 | 231-5145 | 4 | NUT, Flg, USR, 5/16″-18 |
| 28 | 1983286C1 | 2 | CABLE, negative, battery |
| 29 | 1983630C1 | 1 | TERMINAL CONNECTOR, jump start stud |
| 30 | 1987379C1 | 1 | CABLE, positive, battery |
| 31 | 1983285C1 | 1 | CABLE, positive, battery |
| 33 | 1978410C1 | 1 | MOLDING, TRIM – edge, battery box |
| 34 | 413-624 | 1 | BOLT, Hex, 3/8″-16 x 1 1/2″, G5 |
| 35 | 492-11038 | 1 | WASHER, LOCK, 3/8″ |
| 36 | 425-106 | 1 | NUT, 3/8″-16, G5 |
| 1 | A187728 | 1 | MOTOR, STARTER, ASSEMBLY – engine, parts list fig. 4-30 |
| 4 | 493-21052 | 1 | WASHER, LOCK, Int Tooth, 1/2″, internal tooth lock, 1/2 inch, battery terminal |
| 5 | 425-148 | 1 | NUT, Jam, 1/2″-13, G5 |
| 6 | 193-1000 | 1 | NUT, Keps, w/LW,#10-32, hex, with external tooth lock washer, No. 10 NF, switch terminal |
| 7 | 868-12040 | 3 | SCREW, 12 pt, Flg Hd, M12 x 40, 12.9, BOLT – 12 point flange, 12 – 1.75 x 40 mm, class 12.9 |
| 8 | 896-11012 | 3 | WASHER, M13.5 x 24.5 x 3, HT |
| 12 | 91448C2 | 1 | ALTERNATOR, ASSEMBLY – engine, 110 ampere, parts list fig. 4-34 |
| 13 | A189616 | 1 | PULLEY, alternator |
| 14 | J911485 | 1 | SUPPORT, BRACE – alternator |
| 15 | 614-8030 | 1 | BOLT, Hex, M8 x 30, 8.8, Full Thd, Brace to engine |
| 16 | 854-12060 | 1 | BOLT, Hex Flg, M12 x 60, 10.9 |
| 17 | 854-12050 | 1 | BOLT, Hex Flg, M12 x 50, 10.9 |
| 18 | 829-2312 | 2 | NUT, M12 x 1.75, Flg, Cl 10, hex flange, 12 mm – 1.75, class 10 |
| 20 | 426-820 | 1 | BOLT, Hex, 1/2″-13 x 1 1/4″, G8, Full Thd, BOLT – hex, 1/2 NC x 1-1/4 inch, grade 8 |
| 26 | 892-11005 | 4 | WASHER, LOCK, M5 |
| 27 | 824-1405 | 4 | NUT, M5, Cl 5 |
| 28 | 1968023C1 | 1 | PROTECTOR, SHIELD – alternator |
| 30 | 492-11044 | 1 | WASHER, LOCK, 7/16″ |
| 31 | 825-1404 | 1 | NUT, M4, Cl 8 |
| 32 | 892-11004 | 1 | WASHER, LOCK, M4 |
| 33 | 425-147 | 1 | NUT, Jam, 7/16″-14, G5, hex, jam, 7/16 inch NC |
| 1 | A187851 | 1 | HOUSING, FRAME ASSEMBLY – end, commutator |
| 4 | 845-6060 | 4 | BOLT, Hex Flg, M6 x 60, 8.8, BOLT – heavy hex flange, 6 – 1.0 x 60 mm |
| 5 | 825-2306 | 2 | NUT, M6 x 1, Flg, Cl 8, hex flange, 6 mm – 1 |
| 8 | A187857 | 4 | O-RING, sealing |
| 13 | A187852 | 1 | BRUSH HOLDER, ASSEMBLY – brush |
| 14 | A187823 | 4 | SPRING, brush |
| 15 | A187794 | 4 | BRUSH, starter |
| 16 | A47816 | 4 | SCREW, slotted, includes lock washer, 5 – 0.8 x 12 mm |
| 17 | A47813 | 1 | WASHER, end, armature |
| 18 | A187847 | 1 | ARMATURE, starter |
| 22 | A187846 | 1 | HOUSING ASSY., field coil |
| 34 | A187862 | 1 | NUT, hex, terminal |
| 35 | A187858 | 1 | FITTING, CONNECTOR – terminal B |
| 37 | 829-1410 | 1 | NUT, M10, Cl 10 |
| 38 | A187859 | 1 | WASHER, wave |
| 39 | 425-108 | 1 | NUT, 1/2″-13, G5 |
| 41 | A187860 | 1 | WASHER, plate, armature |
| 42 | A187850 | 1 | HOUSING, ASSEMBLY – lever |
| 48 | A187865 | 1 | KIT, pin, lever |
| 53 | A187861 | 4 | SCREW, BOLT – hex, 7 x 23 mm, housing |
| 54 | A187848 | 1 | CLUTCH ASSEMBLY, starter drive |
| 55 | A187855 | 1 | NUT, pinion stop |
| 58 | A47790 | 1 | SNAP RING, collar to shaft |
| 59 | A187853 | 1 | LEVER, ASSEMBLY – clutch, starter |
| 60 | A187854 | 2 | PAD, WEAR, lever |
| 61 | A47786 | 1 | O-RING, clutch housing |
| 62 | A187849 | 1 | HOUSING, ASSEMBLY – clutch drive |
| 64 | A187856 | 6 | SCREW, BOLT – hex, special, drive housing |
| 66 | A187864 | 1 | COVER, KIT – anti-bypass start |
| 68 | A187863 | 1 | SWITCH, SOLENOID, ASSEMBLY – magnetic |
| 65 | 814-6040 | 2 | BOLT, Hex, M6 x 40, 8.8 |
| 1 | 1964731C1 | 1 | HOUSING, collector ring end |
| 3 | 1964737C1 | 1 | BUSHING, expansion |
| 4 | 3079389R1 | 1 | CAPACITOR, suppression |
| 5 | 684857C1 | 1 | SCREW, fillister head, capacitor retaining |
| 6 | A186196 | 1 | WASHER, special |
| 9 | 111899A1 | 1 | REGULATOR, voltage |
| 10 | 3079394R91 | 1 | SET, BRUSHES |
| 11 | 1964734C1 | 2 | SPRING, compression |
| 12 | A186194 | 2 | SCREW, Sltd Truss Hd, M4 x 18, w/LW, BOLT – hex flange, special, regulator |
| 13 | 1964738C1 | 1 | KIT, REPAIR, KIT – terminal hardware |
| 15 | 1546477C1 | 1 | SLEEVE, RING – sleeve, housing ball bearing |
| 16 | 1964732C1 | 1 | RECTIFIER, alternator |
| 17 | A187504 | 2 | SCREW, hex flange, special, rectifier bridge |
| 18 | 1964735C1 | 1 | STATOR, alternator |
| 19 | 1964728C1 | 1 | ROTOR, alternator |
| 20 | 3079410R1 | 1 | RING, collector |
| 21 | 1964730C1 | 1 | BEARING, BALL |
| 22 | 495-21063 | 1 | WASHER, 9/16″, flat, 5/8 x 1-15/32 x 7/64 inch |
| 23 | 231-24410 | 1 | NUT, LOCK, 5/8″-18, GB, hex, self-locking, 5/8 inch NF |
| 26 | 1964727C1 | 1 | PLATE, bearing retaining |
| 27 | 1964726C1 | 1 | BEARING, BALL, drive end |
| 28 | 1964725C1 | 1 | HOUSING, drive end |
| 29 | 1964748C1 | 4 | SCREW, BOLT – fillister head, special, alternator |
| 30 | 1964750C1 | 4 | SCREW, machine, flat head, special, retaining |
| 31 | 1964729C1 | 1 | SPACER, ring |
| 32 | 1964736C1 | 1 | FAN, alternator |
| 34 | A189616 | 1 | PULLEY, alternator |
| 1 | 91971C2 | 1 | LAMP, ASSEMBLY – head, left |
| 1 | 91972C2 | 1 | LAMP, ASSEMBLY – head, right (Shown) |
| 3 | 1964759C1 | 1 | COVER ASSY, access, head lamp assembly |
| 4 | 91967C1 | 1 | BULB, lamp, H4, head assembly |
| 5 | 92242C1 | 1 | BULB, lamp, H3, head assembly |
| 6 | 1964757C1 | 1 | SUPPORT, HOLDER – bulb, H3, head lamp assembly |
| 7 | 1964758C1 | 1 | SPRING, holder, bulb, head lamp assembly |
| 8 | 495-11028 | 6 | WASHER, 1/4″, SAE, flat, 9/32 x 5/8 x 1/16 inch, head lamp assembly |
| 9 | 492-11025 | 6 | WASHER, LOCK, 1/4″, Head lamp assembly |
| 10 | 425-104 | 6 | NUT, 1/4″-20, G5, Head lamp assembly |
| 15 | 92185C1 | 4 | LIGHT ASSY., LAMP – warning, flasher |
| 16 | 130883C1 | 1 | LENS, amber, warning lamp, flasher assembly |
| 18 | A41264 | 1 | BULB, #1156, 12V, Flasher warning assembly |
| 20 | 1974614C2 | 8 | SCREW, SELF TAPPING, Cross Pan Hd, #10-24 x 2 1/4″, Special, Replaces 1276059C1, 2-1/2″ |
| 21 | 231-51409 | 4 | NUT, Flg, USR, #10-24, If used, not shown, flasher warning lamp assembly |
| 22 | 1546476C1 | 2 | LAMP, ASSEMBLY – tail, not available for service, order items 23-31 |
| 23 | A186202 | 2 | LAMP, ASSEMBLY – tail lamp assembly |
| 25 | A186201 | 1 | CABLE PULLING GRIP, HARNESS – includes socket, tail lamp asembly |
| 26 | D71346 | 1 | LAMP, TAIL, lamp, No. 168, replaces 26617R1 bulb, tail assembly |
| 28 | 1283837C1 | 1 | HOUSING, tail lamp, purchase separately, assembly |
| 29 | 140670A1 | 4 | SCREW, hex washer, No. 8 x 3/4 inch, if used, may be replaced by 220408A1 hex washer head screw |
| 30 | 495-31022 | 4 | WASHER, #10, If used, may be replaced by 220408A1 hex washer head screw, item 32, tail lamp |
| 31 | 1327506C1 | 4 | SCREW, SELF TAPPING, Cross Pan Hd, M4.8 x 19, Coated, Tail lamp assembly |
| 32 | 220408A1 | 4 | SCREW, hex washer, No. 8 – 18 x 3/4 inch, special, tail lamp assembly |
| 1 | 92266C2 | 1 | HEADLIGHT, LAMP ASSEMBLY – flood, left, lower |
| 2 | 276498A1 | 1 | LENS, reflector, lamp, replaces 1964807C1 lens, lower front flood assembly |
| 4 | 1312210C2 | 1 | BULB, lamp, Halogen, replaces 1312210C1 bulb, lower front flood assembly |
| 5 | 1964806C1 | 1 | BEZEL, HOUSING – lamp, front, lower flood assembly |
| 6 | 340-1256 | 2 | SCREW, Cross Pan Hd, 1/4″-20 x 3/8″, machine, pan Phillips, 1/4 NC x 3/8 inch, if used, lower front |
| 6 | 760-14319 | 2 | SCREW, SELF TAPPING, Pan Hd, M4.2 x 19, self-tapping, pan Phillips, 4.2 – 1.4 x 19 mm, if used |
| 8 | 895-15010 | 1 | WASHER, M11 x 24 x 2, If Used, Lower front flood lamp assembly |
| 8 | 495-81140 | 1 | WASHER, 13/32″ x 1 1/4″ x .060″, If used, lower front flood lamp assembly |
| 9 | 892-11010 | 1 | WASHER, LOCK, M10, Lower front flood lamp assembly |
| 10 | 825-1410 | 1 | NUT, M10, Cl 8, Lower front flood lamp assembly |
| 11 | 96901C1 | 1 | GROMMET, blower motor wire, lamp wiring, lower front flood assembly |
| 12 | 1334607C2 | 1 | BRACKET, mounting, flood lamp, lower front assembly |
| 13 | 1960750C1 | 3 | SCREW, special, 1/4 NC x 3/8 inch, lower front flood lamp assembly |
| 14 | 1334650C1 | 3 | SHOCK ABSORBER, MOUNT – rubber, lower front flood lamp assembly |
| 15 | 231-5144 | 3 | NUT, Flg, USR, 1/4″-20, Lower front flood lamp assembly |
| 19 | 92269C1 | 1 | LAMP, WORK, ASSEMBLY – flood, fender |
| 20 | 340-1256 | 2 | SCREW, Cross Pan Hd, 1/4″-20 x 3/8″, machine, pan Phillips, 1/4 NC x 3/8 inch, housing, if used |
| 20 | 260-54312 | 2 | SCREW, SELF TAPPING, Cross Pan Hd, #6 x 3/4″, Housing, if used, fender flood lamp asembly |
| 22 | 1312210C2 | 1 | BULB, lamp, Halogen, replaces 1312210C1 bulb, fender flood assembly |
| 23 | 276498A1 | 1 | LENS, reflector, lamp, replaces 1964807C1 lens, fender flood assembly |
| 25 | 1964806C1 | 1 | BEZEL, HOUSING – lamp, front, fender flood assembly |
| 26 | A187915 | 1 | BRACKET, mounting, lamp, fender flood assembly |
| 27 | 814-8045 | 1 | BOLT, Hex, M8 x 45, 8.8, Replaces 931418R1 shoulder bolt, fender flood lamp assembly |
| 28 | 832-41308 | 1 | NUT, M8 x 1.25, Cl 10, hex, self-locking, 8 mm – 1.25, class 10.9, fender flood lamp assembly |
| 29 | 96901C1 | 1 | GROMMET, blower motor wire, lamp wiring, fender flood lamp assembly |
| 30 | 895-15010 | 1 | WASHER, M11 x 24 x 2, If Used, Fender flood lamp assembly |
| 30 | 495-81140 | 1 | WASHER, 13/32″ x 1 1/4″ x .060″, If used, fender flood lamp assembly |
| 31 | 892-11010 | 1 | WASHER, LOCK, M10, Fender flood lamp assembly |
| 32 | 825-1410 | 1 | NUT, M10, Cl 8, Fender flood lamp assembly |
| 3 | 107329C1 | 1 | HARNESS, WIRE, AND CABLE – bulb, console lamp assembly |
| 4 | D71346 | 1 | LAMP, TAIL, lamp, No. 168, console assembly |
| 5 | 1327506C1 | 2 | SCREW, SELF TAPPING, Cross Pan Hd, M4.8 x 19, Coated, Console lamp assembly |
| 7 | 1983391C1 | 1 | LAMP, dome, cab lamp assembly |
| 8 | 1094378R1 | 1 | BULB, J, 12V, 2W, BULB – lamp, cab dome assembly |
| 10 | 92269C1 | 2 | LAMP, WORK, ASSEMBLY – flood, cab lamp assembly |
| 11 | 276498A1 | 1 | LENS, reflector, lamp, replaces 1964807C1 lens, cab flood assembly |
| 12 | 1964806C1 | 1 | BEZEL, HOUSING – lamp, front, cab flood assembly |
| 13 | 340-1256 | 2 | SCREW, Cross Pan Hd, 1/4″-20 x 3/8″, machine, pan Phillips, 1/4 NC x 3/8 inch, housing, if used, cab |
| 13 | 260-54312 | 2 | SCREW, SELF TAPPING, Cross Pan Hd, #6 x 3/4″, Housing, if used, cab flood lamp assembly |
| 15 | 1312210C2 | 1 | BULB, lamp, replaces 1312210C1 bulb, cab flood assembly |
| 16 | A187915 | 1 | BRACKET, mounting, lamp, cab flood assembly |
| 17 | 814-8045 | 1 | BOLT, Hex, M8 x 45, 8.8, Replaces 931418R1 shoulder bolt, cab flood lamp assembly |
| 18 | 832-41308 | 1 | NUT, M8 x 1.25, Cl 10, hex, self-locking, 8 mm – 1.25, class 10.9, cab flood lamp assembly |
| 19 | 495-81140 | 2 | WASHER, 13/32″ x 1 1/4″ x .060″, Cab flood lamp assembly |
| 20 | 892-11010 | 2 | WASHER, LOCK, M10, Cab flood lamp assembly |
| 21 | 825-1410 | 2 | NUT, M10, Cl 8, Cab flood lamp assembly |
| 22 | 96901C1 | 2 | GROMMET, blower motor wire, lamp wiring, cab flood assembly |
| 1 | 1935112C1 | 1 | LIMITER, SPEED, SENSOR – ground speed, remanufactured, North America only, component parts |
| 1 | 1935111C1 | 1 | CORE-MONITOR, RETURN NUMBER – ground speed sensor, use this part number to return sensor |
| 1 | 228760A1 | 1 | RADAR, SENSOR – speed, ground, new, serial number JEE0036210 and after, replaces 1983294C1 |
| 4 | L18337 | 3 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch, nylon |
| 7 | 413-464 | 4 | BOLT, Hex, 1/4″-20 x 4″, G5, Used with item 8 lock washer, item 13 flat washer and item 14, 425-104 |
| 7 | 814-6100 | 4 | BOLT, Hex, M6 x 100, 8.8, Used with item 13 flat washer and item 14, 825-5146 flange nut, if used |
| 8 | 492-11025 | 4 | WASHER, LOCK, 1/4″, Used with item 7, 413-464 bolt, if used |
| 9 | 1960847C2 | 1 | SUPPORT, BRACKET – mounting, speed sensor |
| 10 | 614-10020 | 2 | BOLT, Hex, M10 x 20, 8.8, Full Thd |
| 12 | 895-11010 | 1 | WASHER, M10 x 20 x 2 |
| 13 | 495-11028 | 4 | WASHER, 1/4″, SAE, flat, 9/32 x 5/8 x 1/16 inch |
| 14 | 425-104 | 4 | NUT, 1/4″-20, G5, Used with item 7, 413-464 bolt, if used |
| 14 | 825-5146 | 4 | NUT, M6, Flg Ser, Used with item 7, 814-6100 bolt, if used |
| 1 | 141950A2 | 1 | RADIO, AM-FM stereo, no longer available, order ZAE1000 radio from Ship Direct, replaces |
| 1 | 141951A2 | 1 | RADIO, AM-FM stereo, with cassette tape player, no longer available, order ZAE3000 radio from Ship |
| 2 | 97127C3 | 1 | SUPPORT ASSY., radio |
| 3 | 1327506C1 | 2 | SCREW, SELF TAPPING, Cross Pan Hd, M4.8 x 19, Coated |
| 6 | 97080C1 | 1 | ANTENNA, ASSEMBLY – radio, includes base, mast, cable, and hardware, with straight antenna |
| 7 | 97073C1 | 1 | SUPPORT, BRACKET – mounting, antenna |
| 8 | 97074C1 | 1 | STRAP, ground, antenna |
| 9 | 409-748 | 1 | BOLT, Hex Flg, 1/4″-20 x 1/2″, Serr |
| 10 | 231-5144 | 1 | NUT, Flg, USR, 1/4″-20 |
| 13 | 245343C3 | 2 | SPEAKER, radio, 5 x 7 inch, 4 ohm, oval, if used, see note |
| 14 | 97051C1 | 2 | PLATE ASSY., speaker support, used with 245343C3 oval speakers, if used |
| 15 | 1327506C1 | 8 | SCREW, SELF TAPPING, Cross Pan Hd, M4.8 x 19, Coated, If used |
| 16 | 440-11010 | 8 | SCREW, Cross Pan Hd, #10-24 x 5/8″, machine, pan Phillips, No. 10 NC x 5/8 inch, if used, replaces |
| 17 | 231-51409 | 8 | NUT, Flg, USR, #10-24, If used |
| 20 | 1964958C1 | 1 | KIT, radio support |
| 25 | 1987508C1 | 1 | SUPPRESSOR, blower frequency |
| 26 | 1987509C1 | 1 | SUPPRESSOR, wiper frequency |
| 27 | 182721A1 | 2 | SPEAKER, radio, 5-1/4 inch, round, mounts in rear headliner, if used, see note, Part of the Service Kit |
| 28 | 363-30812 | 8 | SCREW, Hex Wash Hd, #8-32 x 3/4″, machine, hex washer head, No. 8 NC x 3/4 inch, mounts |
| 29 | 195551A1 | 2 | HARNESS, adapter, speakers to headliner harness, used with 182721A1 round speakers, if used, see |
| 1 | A186256 | 1 | WIPER MOTOR, 12 volt |
| 3 | N8359 | 1 | SUPPORT, BRACKET – windshield wiper assembly |
| 4 | N8362 | 3 | SCREW, Hex, M6 x 18.5, Spc, w/LW, with washer, special |
| 5 | N8360 | 1 | SUPPORT, ARM – drive |
| 6 | N8361 | 1 | WASHER, Belleville |
| 7 | L112090 | 1 | NUT, hex, special |
| 10 | N8358 | 1 | ROD, LINK – wiper, pivot |
| 11 | N8356 | 1 | SCREW, Flat Cross Csk Hd, M5 x 8, special, bracket |
| 12 | N14112 | 1 | SHAFT, pivot, wiper |
| 13 | L112089 | 1 | WASHER, wave, special |
| 14 | L112081 | 1 | CAP, pivot shaft end |
| 15 | 825-1408 | 1 | NUT, M8, Cl 8 |
| 17 | A186222 | 1 | WIPER ARM, front, 475 mm (18-3/4 inch) long |
| 18 | 132024A1 | 1 | WIPER BLADE, arm, complete |
| 18 | 132025A1 | 1 | WIPER BLADE, rubber, 500 mm long, windshield wiper refill |
| 19 | 414-410 | 2 | BOLT, Hex, 1/4″-28 x 5/8″, G5, Full Thd, BOLT – hex, 1/4 NF x 5/8 inch, wiper bracket mounting |
| 1 | F93209 | 1 | WIPER MOTOR, ASSEMBLY |
| 2 | D71417 | 1 | WASHER, SPECIAL, flat, leather |
| 3 | 495-81032 | 1 | WASHER, 23/32″ x 1 1/4″ x .060″, flat, 23/32 x 1 -1/4 x 3/64 inch, wiper motor, replaces D71418 |
| 4 | D74631 | 1 | NUT, hex, 5/8 inch – 24 extra fine thread |
| 5 | A165073 | 1 | WASHER, nylon, 5/8 x 1-1/2 x 7/64 inch |
| 6 | A165074 | 1 | SPACER, SPACER – nylon, 7/8 inch OD |
| 7 | F64198 | 1 | SPACER, SPACER – nylon, black, motor mounting |
| 8 | 142-102 | 1 | SCREW, Cross Oval Hd, #10-24 x 3/4″, machine, oval Phillips, No. 10 NC x 3/4 inch |
| 9 | A165076 | 1 | WASHER, nylon, 5/16 x 1 x 7/64 inch |
| 10 | 230-42409 | 1 | NUT, LOCK, #10-24, GA, hex, self-locking, No. 10 NC |
| 11 | D78019 | 1 | WIPER ARM, blade, 12 inch |
| 12 | A42580 | 1 | BLADE, WIPER, arm, rear, 406 mm (16 inch) long |
| 13 | 170-105 | 1 | SCREW, Sltd Pan Hd, #5-40 x 1/2″, machine, pan head slotted, No. 5 NC x 1/2 inch |
| 14 | 225-14105 | 1 | NUT, #5-40, Blade attaching |
| 1 | 1968022C1 | 1 | SUPPORT, BRACKET – mounting, windshield washer reservoir and pump |
| 2 | K304597 | 1 | SUPPORT, BRACKET – reservoir mounting |
| 3 | 495-21031 | 2 | WASHER, 1/4″, flat, 5/16 x 3/4 x 1/16 inch |
| 4 | 425-104 | 2 | NUT, 1/4″-20, G5 |
| 5 | K304596 | 1 | RESERVOIR, AND PUMP ASSEMBLY – washer fluid, component parts not serviced separately |
| 8 | 1968057C1 | 1 | HOSE, TUBING – washer, 4 inch (100 mm) long (See Note) |
| 9 | K307050 | 1 | VALVE, non-return |
| 10 | 1968058C1 | 1 | HOSE, TUBING – washer, 141-3/4 inch (3600 mm) long (See Note) |
| 11 | L18337 | 6 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch, harness |
| 12 | 1964673C1 | 1 | HARNESS, wiring, washer pump |
| 19 | 1968053C1 | 1 | ELBOW, ELBOW – 90 degree, special, mounts to 1968052C1 bracket, item 32 |
| 20 | N8361 | 1 | WASHER, Belleville |
| 21 | 825-1408 | 1 | NUT, M8, Cl 8 |
| 24 | 1968059C1 | 1 | HOSE, TUBING – washer, 19-11/16 inch (500 mm) long (See Note) |
| 25 | 1968054C1 | 1 | JET, NOZZLE – windshield washer |
| 30 | 1968129C1 | 1 | FITTING, TEE – nylon, barb ends (Converting for rear washer) |
| 31 | 1968130C1 | 2 | CLIP, nozzle (Converting for rear washer) |
| 32 | 1968052C1 | 1 | BRACKET, connector, to bulkhead, not shown |
| 1 | 1989917C1 | 1 | HOUSING, support, steering |
| 2 | 1954243C2 | 1 | TUBE, steering wheel, no longer available, order B92960 kit, if used |
| 3 | 148424C2 | 2 | BUSHING, lower, steering tube |
| 4 | 103985C1 | 2 | BUSHING, upper, steering tube |
| 5 | 1348393C1 | 1 | O-RING, steering column cap |
| 6 | 148921C1 | 1 | CAP, column, steering |
| 7 | 1954248C1 | 1 | PIN, LARGE, stop, telescoping, no longer available, order B92960 kit, if used |
| 11 | 1954245C1 | 1 | SHIELD, outer, column |
| 12 | 1954244C1 | 1 | PROTECTOR, SHIELD – inner, column |
| 13 | 1954247C1 | 1 | SHAFT, telescoping, no longer available, order B92960 kit |
| 14 | A65544 | 1 | WHEEL (STEERING), 15-1/4 inch |
| 15 | A141827 | 1 | CAP, KNOB – lock, wheel, round center hole, used with item 13 shaft, no longer available, order |
| 17 | 425-146 | 1 | NUT, Jam, 3/8″-16, G5, hex, jam, 3/8 inch NC |
| 18 | 1954249C2 | 1 | PIN, LINCH, CLIP – stop upper, if used |
| 19 | 1954250C1 | 1 | GASKET, COLLAR – lower, no longer available, order B92960 kit, if used |
| 22 | 1954253C1 | 1 | RING, SNAP, #87, Ext, Crescent, #87, Ext, if used |
| 23 | F19646 | 1 | NUT, SPECIAL, 13/16″-20, Thin, lock, steering wheel retaining |
| 24 | A180055 | 1 | CAP ASSY., INSERT – Case Globe and Eagle, if used |
| 24 | 1342054C1 | 1 | PLASTIC PLUG, INSERT – plastic, black, if used |
| 25 | 114983A1 | 1 | BEZEL, eagle medallion, adhesive backing, locations other than steering insert |
| 26 | 1954246C1 | 1 | WASHER, shield |
| 27 | 1974720C2 | 1 | BOOT, column |
| 28 | 1975919C1 | 4 | SCREW, special |
| 29 | 104036C1 | 4 | NUT, expansion |
| 31 | 104008C1 | 1 | INSULATOR, RUBBER, vibration, shaft |
| 32 | 148431C1 | 1 | JOINT, universal |
| 33 | 438-32428 | 2 | PIN, 3/8″ x 1 3/4″, Coiled, 3/8″ x 1 3/4″, Coiled, replaces 617944R1 pin |
| 34 | 148426C2 | 1 | SUPPORT ASSY., column |
| 35 | 614-8025 | 2 | BOLT, Hex, M8 x 25, 8.8 |
| 36 | 829-1408 | 2 | NUT, M8, Cl 10 |
| 37 | 837-10016 | 2 | DOWEL, M10 x 16, dowel, 10 x 16 mm, hardened |
| 38 | 614-10035 | 3 | BOLT, Hex, M10 x 35, 8.8, Full Thd |
| 39 | 496-81003 | 3 | WASHER, 13/32″ x 1 1/16″ x .095″, HDN, flat, 13/32 x 1-1/16 x 3/32 inch, hardened |
| 40 | 104809C1 | 3 | BUSHING, vibration damper |
| 41 | 614-10020 | 2 | BOLT, Hex, M10 x 20, 8.8, Full Thd |
| 44 | 148920C1 | 2 | BUSHING, pivot, column |
| 45 | 892-11012 | 2 | WASHER, LOCK, M12 |
| 46 | 814-12050 | 2 | BOLT, Hex, M12 x 50, 8.8 |
| 47 | 97109C1 | 1 | LEVER, release, tilt |
| 48 | 97111C4 | 1 | HANDLE, lever |
| 49 | 170-101 | 1 | SCREW, Slotted Pan Hd, #8-32 x 5/16″, No. 8 x 5/16 inch |
| 50 | 96972C1 | 1 | PLATE ASSY., detent, tilt |
| 51 | 614-8016 | 2 | BOLT, Hex, M8 x 16, 8.8 |
| 52 | 538321R1 | 1 | SPRING, detent |
| 53 | 148480C1 | 1 | SPRING, support, tilt |
| 54 | 228340A1 | 1 | WASHER, rubber, snubber, 7/8 inch ID, if used |
| 55 | 100-1187 | 1 | RING, SNAP, #87, Ext, If used |
| 56 | 100-1587 | 1 | RING, SNAP, #87, Ext, Crescent, If used |
| 1 | 1989917C1 | 1 | HOUSING, support, steering |
| 2 | 148424C2 | 2 | BUSHING, lower, steering tube, Part of the Steering Column Modification Kit P/N B92960 |
| 3 | 103985C1 | 2 | BUSHING, upper, steering tube, Part of the Steering Column Modification Kit P/N B92960 |
| 4 | 1954243C2 | 1 | TUBE, steering wheel, telescoping, no longer available, order B92960 kit, if used |
| 5 | 148921C1 | 1 | CAP, column |
| 8 | 1348393C1 | 1 | O-RING, steering column cap, Part of the Steering Column Modification Kit P/N B92960 |
| 9 | 1954246C1 | 1 | WASHER, shield |
| 10 | 1954248C1 | 1 | PIN, LARGE, stop, no longer available, order B92960 kit, if used |
| 11 | 1954247C1 | 1 | SHAFT, telescoping, if replacing item 11 shaft or item 23 hub, order B92960 kit, see below |
| 12 | 1954249C2 | 1 | PIN, LINCH, CLIP – pin, stop, no longer available, order B92960 kit, if used |
| 13 | 1954250C1 | 1 | GASKET, COLLAR – lower, shaft, no longer available, order B92960 kit, if used |
| 14 | 1974758C1 | 1 | SPACER, wheel, steering, no longer available, order B92960, if used |
| 15 | 1954244C1 | 1 | PROTECTOR, SHIELD – inner |
| 17 | 1340252C1 | 1 | WHEEL (STEERING) |
| 18 | 1340455C1 | 1 | HUB, column |
| 21 | 260-54310 | 3 | SCREW, SELF TAPPING, Cross Pan Hd, #6 x 5/8″, self-tapping, pan Phillips, No. 6-20 x 5/8 inch |
| 22 | F19646 | 1 | NUT, SPECIAL, 13/16″-20, Thin, lock, steering wheel retaining |
| 23 | 1974628C1 | 1 | HUB, lock, wheel, round center hole, used with item 11 shaft, if ordering item 11 shaft or item 23 hub |
| 24 | 425-146 | 1 | NUT, Jam, 3/8″-16, G5, hex, jam, 3/8 inch NC |
| 25 | A180055 | 1 | CAP ASSY., INSERT – Case Globe and Eagle, emblem, if used, Part of the Steering Column |
| 25 | 1342054C1 | 1 | PLASTIC PLUG, INSERT – plastic, black, if used |
| 26 | 114983A1 | 1 | BEZEL, eagle medallion, adhesive backing, locations other than steering insert |
| 27 | 1974720C2 | 1 | BOOT, column |
| 28 | 1975919C1 | 4 | SCREW, special |
| 29 | 104036C1 | 4 | NUT, expansion |
| 31 | 104008C1 | 1 | INSULATOR, RUBBER, vibration, shaft |
| 32 | 148431C1 | 1 | JOINT, universal |
| 33 | 438-32428 | 2 | PIN, 3/8″ x 1 3/4″, Coiled, 3/8″ x 1 3/4″, Coiled, replaces 617944R1 pin |
| 34 | 148426C2 | 1 | SUPPORT ASSY., column |
| 35 | 614-8025 | 2 | BOLT, Hex, M8 x 25, 8.8 |
| 36 | 829-1408 | 2 | NUT, M8, Cl 10 |
| 37 | 837-10016 | 2 | DOWEL, M10 x 16, dowel, 10 x 16 mm, hardened |
| 38 | 614-10035 | 3 | BOLT, Hex, M10 x 35, 8.8, Full Thd |
| 39 | 496-81003 | 3 | WASHER, 13/32″ x 1 1/16″ x .095″, HDN, flat, 13/32 x 1-1/16 x 3/32 inch, hardened |
| 40 | 104809C1 | 3 | BUSHING, vibration damper |
| 41 | 614-10020 | 2 | BOLT, Hex, M10 x 20, 8.8, Full Thd |
| 44 | 148920C1 | 2 | BUSHING, pivot, column |
| 45 | 892-11012 | 2 | WASHER, LOCK, M12 |
| 46 | 814-12050 | 2 | BOLT, Hex, M12 x 50, 8.8 |
| 47 | 97109C1 | 1 | LEVER, release, tilt |
| 48 | 97111C4 | 1 | HANDLE, lever |
| 49 | 170-101 | 1 | SCREW, Slotted Pan Hd, #8-32 x 5/16″, No. 8 x 5/16 inch |
| 50 | 96972C1 | 1 | PLATE ASSY., detent, tilt |
| 51 | 614-8016 | 2 | BOLT, Hex, M8 x 16, 8.8 |
| 52 | 538321R1 | 1 | SPRING, detent |
| 53 | 148480C1 | 1 | SPRING, support, tilt |
| 54 | 228340A1 | 1 | WASHER, rubber, snubber, 7/8 inch ID, if used |
| 55 | 100-1187 | 1 | RING, SNAP, #87, Ext, If used |
| 56 | 100-1587 | 1 | RING, SNAP, #87, Ext, Crescent, If used |
| 1 | 1994591C4 | 1 | VALVE, ASSEMBLY – priority steering, parts list fig. 5-22 |
| 2 | 238-6117 | 1 | O-RING, -117, 90 Duro, .799″ ID x .103″ Thk, Priority valve seal |
| 3 | 201-308 | 1 | ELBOW, 90є, 1 7/16″-12 x 1 5/8″-12, Adj, ORFS, 90 deg, 1-7/16-12 face x 1-5/16-12 inch adj O-ring |
| 4 | 237-6016 | 1 | O-RING, 16-1, 90 Duro, 1.171″ ID x .118″ Thk |
| 5 | 238-6021 | 1 | O-RING, -021, 90 Duro, .926″ ID x .070″ Thk |
| 6 | 201-307 | 1 | ELBOW, 90є, 1 3/16″-12 x 1 1/16″-12 Adj, ORFS, 90 degree, 1-3/16-12 face seal x 1-1/16-12 inch adj |
| 7 | 237-6012 | 1 | O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk |
| 8 | 238-6018 | 1 | O-RING, -018, 90 Duro, .739″ ID x .070″ Thk |
| 9 | 201-102 | 1 | CONNECTOR, HYD., 13/16″-16 ORFS x 3/4″-16 ORB |
| 10 | 237-6008 | 1 | O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk |
| 11 | 238-6014 | 1 | O-RING, -014, 90 Duro, .489″ ID x .070″ Thk |
| 12 | 201-101 | 2 | CONNECTOR, HYD., 11/16″-16 ORFS x 9/16″-18 ORB, ADAPTER – straight, 11/16-16 face seal x |
| 14 | 238-6012 | 1 | O-RING, -012, 90 Duro, .364″ ID x .070″ Thk |
| 17 | 1340547C1 | 1 | TUBE ASSY., supply, steering |
| 19 | 238-6014 | 1 | O-RING, -014, 90 Duro, .489″ ID x .070″ Thk |
| 21 | 1289489C3 | 1 | TUBE ASSY., steering, signal rear |
| 22 | 238-6012 | 1 | O-RING, -012, 90 Duro, .364″ ID x .070″ Thk |
| 23 | 1340546C1 | 1 | PIPE, TUBE – steering, signal front |
| 25 | 238-6012 | 1 | O-RING, -012, 90 Duro, .364″ ID x .070″ Thk |
| 29 | 1289370C2 | 1 | TUBE ASSY., pump, signal short, prior to P.I.N. JJA0072000 |
| 29 | 252478A3 | 1 | TUBE ASSY., pump, signal short, effective P.I.N. JJA0072001 and above |
| 30 | 1334536C2 | 1 | CLAMP, 3/8 inch OD tube |
| 31 | 1334535C2 | 1 | SUPPORT, PLATE – tube, clamp |
| 32 | 614-6012 | 1 | BOLT, Hex, M6 x 12, 8.8 |
| 33 | 201-408 | 1 | TEE, 11/16″-16 ORFS, 11/16-16 inch face seal branch x face seal x face seal |
| 34 | 238-6012 | 3 | O-RING, -012, 90 Duro, .364″ ID x .070″ Thk |
| 37 | 1340548C3 | 1 | SUPPORT, BRACKET – support, tube |
| 38 | 614-10025 | 2 | BOLT, Hex, M10 x 25, 8.8, Full Thd |
| 39 | 895-11010 | 2 | WASHER, M10 x 20 x 2 |
| 40 | 825-1410 | 2 | NUT, M10, Cl 8 |
| 42 | 614-8020 | 6 | BOLT, Hex, M8 x 20, 8.8 |
| 43 | 825-1408 | 6 | NUT, M8, Cl 8 |
| 44 | 1348408C1 | 1 | CLAMP, tube retaining |
| 45 | 218-5158 | 1 | PLUG, Hex Hd, 1 1/16″-12 ORB, hex, 1-1/16-12 inch O-ring boss (without hitch) |
| 46 | 237-6012 | 1 | O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk |
| 13 | 237-6006 | 1 | O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk |
| 2 | 1977683C1 | 1 | SEAL ASSY., dust, shaft |
| 3 | 104008C1 | 1 | INSULATOR, RUBBER, vibration, shaft |
| 4 | 1344478C1 | 1 | SUPPORT, BRACKET – mounting, pump |
| 5 | 413-510 | 4 | BOLT, Hex, 5/16″-18 x 5/8″, G5, Full Thd |
| 6 | 104809C1 | 3 | BUSHING, vibration damper, pump |
| 7 | 496-81003 | 3 | WASHER, 13/32″ x 1 1/16″ x .095″, HDN, flat, 13/32 x 1-1/16 x 3/32 inch, hardened |
| 8 | 614-10035 | 3 | BOLT, Hex, M10 x 35, 8.8, Full Thd |
| 9 | 201-102 | 4 | CONNECTOR, HYD., 13/16″-16 ORFS x 3/4″-16 ORB |
| 10 | 237-6008 | 1 | O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk, Boss end |
| 11 | 238-6014 | 1 | O-RING, -014, 90 Duro, .489″ ID x .070″ Thk, Face end |
| 12 | 201-303 | 1 | ELBOW, 90є, 9/16″-18 x 7/16″-20 Adj, ORFS, 90 degree, 9/16-18 face seal x 7/16-20 inch adj O-ring |
| 13 | 237-6004 | 1 | O-RING, 4-1, 90 Duro, .351″ ID x .072″ Thk, Boss end |
| 14 | 238-6011 | 1 | O-RING, -011, 90 Duro, .301″ ID x .070″ Thk, Face end |
| 15 | 1334378C1 | 1 | HOSE ASSY., 533 mm (21 inch) long |
| 16 | 1978481C1 | 1 | PIPE, TUBE – steering supply, upper |
| 17 | 1342026C2 | 1 | PIPE, SLEEVE – corrugated, bulk, 32 (1-1/4) x 37 (1-7/16) x 565 mm (22-1/4 inch) long |
| 18 | 1342123C2 | 1 | HOSE, return, 967 mm (38-1/8 inch) long |
| 19 | 1334592C4 | 1 | PIPE, SLEEVE – corrugated, bulk, 41 (1-5/8) x 49 (1-15/16) x 585 mm (23-1/32 inch) long |
| 20 | 1542766C1 | 1 | HOSE, steering signal, 650 mm (25-5/8 inch) long |
| 21 | 1968083C3 | 1 | HOSE, PROTECTION, SLEEVE – corrugated, 940 mm (37 inch) long, cut from 1978484C2 bulk sleeve |
| 22 | 1978482C1 | 1 | PIPE, TUBE – steering return |
| 22 | 238-6016 | 1 | O-RING, -016, 90 Duro, .614″ ID x .070″ Thk |
| 23 | 1978480C1 | 2 | PIPE, TUBE – right and left turn |
| 25 | 1334208C1 | 1 | HOSE ASSY., 2692 mm (106 inch) long, left turn |
| 26 | 1976794C1 | 1 | HOSE ASSY., 2108 mm (83 inch) long, right turn |
| 27 | 1342026C2 | 2 | PIPE, SLEEVE – corrugated, bulk, 32 (1-1/4) x 37 (1-7/16) x 565 mm (22-1/4 inch) long |
| 28 | 201-101 | 2 | CONNECTOR, HYD., 11/16″-16 ORFS x 9/16″-18 ORB, ADAPTER – straight, 11/16-16 face seal x |
| 29 | 237-6006 | 1 | O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk, Boss end |
| 30 | 238-6012 | 1 | O-RING, -012, 90 Duro, .364″ ID x .070″ Thk, Face end |
| 35 | 238-6012 | 1 | O-RING, -012, 90 Duro, .364″ ID x .070″ Thk |
| 36 | 238-6014 | 4 | O-RING, -014, 90 Duro, .489″ ID x .070″ Thk |
| 38 | 238-6018 | 1 | O-RING, -018, 90 Duro, .739″ ID x .070″ Thk |
| 2 | 1977683C1 | 1 | SEAL ASSY., dust, shaft |
| 3 | 104008C1 | 1 | INSULATOR, RUBBER, vibration, shaft |
| 4 | 1344478C1 | 1 | SUPPORT, BRACKET – mounting, pump |
| 5 | 413-510 | 4 | BOLT, Hex, 5/16″-18 x 5/8″, G5, Full Thd |
| 6 | 104809C1 | 3 | BUSHING, vibration damper, pump |
| 7 | 496-81003 | 3 | WASHER, 13/32″ x 1 1/16″ x .095″, HDN, flat, 13/32 x 1-1/16 x 3/32 inch, hardened |
| 8 | 614-10035 | 3 | BOLT, Hex, M10 x 35, 8.8, Full Thd |
| 9 | 201-102 | 4 | CONNECTOR, HYD., 13/16″-16 ORFS x 3/4″-16 ORB |
| 10 | 237-6008 | 1 | O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk, Boss end |
| 11 | 238-6014 | 1 | O-RING, -014, 90 Duro, .489″ ID x .070″ Thk, Face end |
| 12 | 201-303 | 1 | ELBOW, 90є, 9/16″-18 x 7/16″-20 Adj, ORFS, 90 degree, 9/16-18 face seal x 7/16-20 inch adj O-ring |
| 13 | 237-6004 | 1 | O-RING, 4-1, 90 Duro, .351″ ID x .072″ Thk, Boss end |
| 14 | 238-6011 | 1 | O-RING, -011, 90 Duro, .301″ ID x .070″ Thk, Face end |
| 15 | 1334378C1 | 1 | HOSE ASSY., 533 mm (21 inch) long |
| 16 | 1978481C1 | 1 | PIPE, TUBE – steering supply, upper |
| 17 | 1342026C2 | 1 | PIPE, SLEEVE – corrugated, bulk, 32 (1-1/4) x 37 (1-7/16) x 565 mm (22-1/4 inch) long |
| 18 | 1342123C2 | 1 | HOSE, return, 967 mm (38-1/8 inch) long, steering |
| 19 | 1334592C4 | 1 | PIPE, SLEEVE – corrugated, bulk, 41 (1-5/8) x 49 (1-15/16) x 585 mm (23-1/32 inch) long, cut to 475 |
| 20 | 1542766C1 | 1 | HOSE, steering signal, 650 mm (25-5/8 inch) long |
| 21 | 1968083C3 | 1 | HOSE, PROTECTION, SLEEVE – corrugated, 940 mm (37 inch) long, cut from 1978484C2 bulk sleeve |
| 22 | 1978482C1 | 1 | PIPE, TUBE – steering return |
| 22 | 238-6016 | 1 | O-RING, -016, 90 Duro, .614″ ID x .070″ Thk |
| 23 | 1978480C1 | 2 | PIPE, TUBE – right and left turn |
| 25 | 1976786C1 | 1 | HOSE ASSY., 2515 mm (99 inch) long, right turn |
| 26 | 1976799C1 | 1 | HOSE ASSY., 2108 mm (83 inch) long, left turn |
| 27 | 1342026C2 | 2 | PIPE, SLEEVE – corrugated, bulk, 32 (1-1/4) x 37 (1-7/16) x 565 mm (22-1/4 inch) long |
| 28 | 1978404C1 | 2 | HOSE ASSY., crossover, 787 mm (31 inch) long 31″ overall length – 100R17 – 3/8″ hose – both female |
| 29 | 201-304 | 2 | ELBOW, 90є, 11/16″-16 x 9/16″-18 Adj, ORFS, 90 degree, 11/16-16 face seal x 9/16-18 inch adj |
| 30 | 237-6006 | 1 | O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk, Boss end |
| 31 | 238-6012 | 1 | O-RING, -012, 90 Duro, .364″ ID x .070″ Thk, Face end |
| 32 | 201-412 | 2 | TEE, 13/16″-16 x 3/4″-16 Run, ORFS, 13/16 -16 face branch x face x 3/4-16 inch adj O-ring |
| 33 | 237-6008 | 1 | O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk, Boss end |
| 34 | 238-6014 | 2 | O-RING, -014, 90 Duro, .489″ ID x .070″ Thk, Face end |
| 35 | 238-6012 | 1 | O-RING, -012, 90 Duro, .364″ ID x .070″ Thk |
| 36 | 238-6014 | 4 | O-RING, -014, 90 Duro, .489″ ID x .070″ Thk |
| 38 | 238-6018 | 1 | O-RING, -018, 90 Duro, .739″ ID x .070″ Thk |
| 1 | 1348392C2 | 1 | COOLER, OIL, hydraulic, replaces 1348392C1 cooler |
| 2 | A160194 | 1 | SUPPORT, BRACKET – pivot, oil cooler |
| 3 | 413-510 | 2 | BOLT, Hex, 5/16″-18 x 5/8″, G5, Full Thd |
| 4 | 492-11031 | 4 | WASHER, LOCK, 5/16″ |
| 5 | 103632A1 | 1 | SCREW, BOLT – hex, 1/4 NC x 12-3/4 inch |
| 6 | 231-1444 | 1 | NUT, LOCK, 1/4″-20, GB |
| 7 | 413-512 | 2 | BOLT, Hex, 5/16″-18 x 3/4″, G5, Full Thd, hex, 5/16 NC x 3/4 inch |
| 8 | 495-11034 | 2 | WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch |
| 15 | 1340524C1 | 1 | HOSE ASSY., 2781 mm (109-1/2 inch) long, cooler supply |
| 21 | 238-6016 | 2 | O-RING, -016, 90 Duro, .614″ ID x .070″ Thk |
| 22 | 238-6018 | 2 | O-RING, -018, 90 Duro, .739″ ID x .070″ Thk |
| 28 | 1348339C1 | 1 | HOSE ASSY., cooler return, 3226 mm (127 inch) long |
| 29 | 1334592C4 | 1 | PIPE, SLEEVE – corrugated, bulk, 41 (1-5/8) x 49 (1-15/16) x 585 mm (23-1/32 inch) long |
| 30 | 306132C1 | 1 | STRAP, CABLE, .30″ x 14.5″, tie, 14 inch long, nylon |
| 31 | 1348391C1 | 1 | TUBE, cooler supply, mounts to PTO valve on fig. 8-6 |
| 32 | 201-104 | 1 | CONNECTOR, HYD., 1 3/16″-12 ORFS x 1 1/16″-12 ORB |
| 33 | 237-6012 | 1 | O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk |
| 34 | 238-6018 | 1 | O-RING, -018, 90 Duro, .739″ ID x .070″ Thk |
| 1 | 181582A2 | 1 | COOLER, OIL, hydraulic |
| 2 | 181583A1 | 1 | CONDENSER, air conditioning |
| 3 | 238-6018 | 2 | O-RING, -018, 90 Duro, .739″ ID x .070″ Thk, Cooler tubes to condenser tubes |
| 4 | 224497A2 | 2 | PIPE, TUBE – oil cooler to transmission hoses |
| 5 | 844-8020 | 4 | BOLT, Hex Flg, M8 x 20, 8.8 |
| 6 | 832-10408 | 4 | NUT, LOCK, M8 x 1.25, Cl 8 |
| 7 | 182351A2 | 1 | SUPPORT, BRACKET – upper, pivot |
| 8 | 224081A1 | 1 | SUPPORT, BRACKET – lower |
| 10 | 832-10408 | 2 | NUT, LOCK, M8 x 1.25, Cl 8 |
| 11 | 614-8020 | 4 | BOLT, Hex, M8 x 20, 8.8 |
| 12 | 492-11031 | 4 | WASHER, LOCK, 5/16″ |
| 13 | 895-15008 | 4 | WASHER, M8 x 20 x 1.6 |
| 14 | 413-512 | 2 | BOLT, Hex, 5/16″-18 x 3/4″, G5, Full Thd, hex, 5/16 NC x 3/4 inch |
| 15 | 492-11031 | 2 | WASHER, LOCK, 5/16″ |
| 16 | 495-11034 | 2 | WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch |
| 17 | 225398A2 | 1 | HOSE, 3340 mm (131-1/2 inch) long, cooler supply |
| 18 | 225399A2 | 1 | HOSE, 3632 mm (143 inch) long, cooler return |
| 19 | 238-6018 | 4 | O-RING, -018, 90 Duro, .739″ ID x .070″ Thk |
| 20 | 1334592C4 | 1 | PIPE, SLEEVE – corrugated, bulk, 41 (1-5/8) x 49 (1-15/16) x 585 mm (23-1/32 inch) long |
| 21 | L18337 | 1 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch, nylon |
| 22 | 1348391C1 | 1 | TUBE, cooler supply, mounts to PTO valve on fig. 8-8 |
| 23 | 201-104 | 1 | CONNECTOR, HYD., 1 3/16″-12 ORFS x 1 1/16″-12 ORB |
| 24 | 237-6012 | 1 | O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk |
| 25 | 238-6018 | 1 | O-RING, -018, 90 Duro, .739″ ID x .070″ Thk |
| 10 | N6392 | 3 | O-RING, end cap, Part of the Seal Kit P/N 1343658C3 |
| 11 | S113037 | 1 | PLATE, spacer |
| 12 | L30878 | 1 | SHAFT, DRIVE, gerotor |
| 13 | 1343636C1 | 1 | ROTOR, GEROTOR – pump |
| 14 | 1343644C1 | 1 | SPACER, gerotor |
| 15 | 136493A1 | 1 | COVER, KIT – repair, end cap and spacer plate, also includes 7 bolts, replaces D82809 end cap |
| 16 | 79-1532 | 7 | SCREW, 12 Pt Flg, 5/16″-24 x 2″, G8, BOLT – 12 point flange, 5/16 NC x 2 inch, grade 8, replaces |
| 18 | L35368 | 1 | RETAINER, check ball |
| 19 | 211-1010 | 1 | BALL, 5/16″ Dia, chrome alloy steel, 5/16 inch, grade 24 |
| 20 | L30893 | 1 | O-RING, 5/16 ID x 1/8 inch wide, seal, Part of the Seal Kit P/N 1343658C3 |
| 21 | D82806 | 1 | VALVE SEAT, ball |
| 22 | 238-5012 | 1 | O-RING, -012, 70 Duro, .364″ ID x .070″ Thk, Replaces N8539, Part of the Seal Kit P/N 1343658C3 |
| 23 | D82805 | 1 | PLUG, SCREW – set |
| 26 | D82804 | 2 | RACE, thrust, bearing |
| 27 | G13609 | 1 | BEARING, THRUST, roller, thrust |
| 28 | 121179A1 | 1 | SEAL, teflon, shaft, Part of the Seal Kit P/N 1343658C3 |
| 31 | 238-5225 | 1 | O-RING, -225, 70 Duro, 1.859″ ID x .139″ Thk, Replaces A14515 seal, Part of the Seal Kit P/N |
| 32 | N13312 | 1 | CAP CYLINDER END, BUSHING – seal gland |
| 33 | S110169 | 1 | WASHER, RING – retaining |
| 34 | 697494R91 | 1 | SEAL, SHAFT, 1 inch ID, spool, replaces A28211 seal, Part of the Seal Kit P/N 1343658C3 |
| 37 | 1343647C1 | 1 | HOUSING, COLUMN ASSEMBLY – pump, not included with pump, order separately |
| 38 | 1343650C1 | 4 | SCREW, 12 Pt Flg, 3/8″-16 x 1″, G8 |
| 39 | 225388A2 | 1 | PUMP, ASSEMBLY – steering, hydrostatic, component parts are not serviced separately, not shown, if |
| 10 | N6392 | 3 | O-RING, end cap, Part of the Seal Kit P/N 1343658C3 |
| 11 | S113037 | 1 | PLATE, spacer |
| 12 | L30878 | 1 | SHAFT, DRIVE, gerotor |
| 13 | 1343637C1 | 1 | GEAR-SET, GEROTOR – pump |
| 14 | 1343645C1 | 1 | SPACER, gerotor |
| 15 | 136493A1 | 1 | COVER, KIT – repair, end cap and spacer plate, also includes 7 bolts, replaces D82809 end cap |
| 16 | 1343640C1 | 7 | SCREW, 12 Pt Flg, 5/16″-18 x 2 1/4″, G8 |
| 18 | L35368 | 1 | RETAINER, check ball |
| 19 | 211-1010 | 1 | BALL, 5/16″ Dia, chrome alloy steel, 5/16 inch, grade 24 |
| 20 | L30893 | 1 | O-RING, 5/16 ID x 1/8 inch wide, seal, Part of the Seal Kit P/N 1343658C3 |
| 21 | D82806 | 1 | VALVE SEAT, ball |
| 22 | 238-5012 | 1 | O-RING, -012, 70 Duro, .364″ ID x .070″ Thk, Replaces N8539, Part of the Seal Kit P/N 1343658C3 |
| 23 | D82805 | 1 | PLUG, SCREW – set |
| 26 | D82804 | 2 | RACE, thrust, bearing |
| 27 | G13609 | 1 | BEARING, THRUST, roller, thrust |
| 28 | 121179A1 | 1 | SEAL, teflon, shaft, Part of the Seal Kit P/N 1343658C3 |
| 31 | 238-5225 | 1 | O-RING, -225, 70 Duro, 1.859″ ID x .139″ Thk, Replaces A14515 seal, Part of the Seal Kit P/N |
| 32 | N13312 | 1 | CAP CYLINDER END, BUSHING – seal gland |
| 33 | S110169 | 1 | WASHER, RING – retaining |
| 34 | 697494R91 | 1 | SEAL, SHAFT, 1 inch ID, spool, replaces A28211, Part of the Seal Kit P/N 1343658C3 |
| 37 | 1343647C1 | 1 | HOUSING, COLUMN ASSEMBLY – pump, no longer included with pump, order separately |
| 38 | 1343650C1 | 4 | SCREW, 12 Pt Flg, 3/8″-16 x 1″, G8 |
| 39 | 225390A1 | 1 | PUMP, ASSEMBLY – steering, hydrostatic, component parts are not serviced separately, not shown, if |
| 1 | 1978362C1 | 1 | BODY, valve |
| 3 | 1994566C1 | 1 | PLUG, orifice |
| 5 | G108700 | 2 | PLUG, orifice, spool |
| 6 | G110111 | 1 | SPRING, VALVE, priority |
| 7 | 118923A2 | 1 | PLUG, orifice, replaces 118923A1 plug |
| 8 | 86625138 | 1 | PLUG, Hex Soc, 7/8″-14 ORB |
| 9 | 237-6010 | 1 | O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk |
| 13 | 1994581C1 | 1 | SPRING, load check |
| 14 | G108723 | 1 | RING, backup |
| 15 | 1543329C1 | 1 | POPPET, VALVE, PLUG |
| 16 | 238-6015 | 1 | O-RING, -015, 90 Duro, .551″ ID x .070″ Thk |
| 23 | 238-6018 | 1 | O-RING, -018, 90 Duro, .739″ ID x .070″ Thk |
| 24 | G35540 | 1 | RING, backup |
| 25 | 238-6012 | 1 | O-RING, -012, 90 Duro, .364″ ID x .070″ Thk |
| 26 | 237-6012 | 1 | O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk |
| 27 | 425-1510 | 1 | NUT, Jam, 5/8″-18, G5, Hex |
| 28 | G108556 | 1 | POPPET, VALVE, relief |
| 30 | G108867 | 1 | PLUG, special, adjusting screw |
| 31 | G108866 | 1 | HOUSING, BODY – pilot relief |
| 1 | 1954124C4 | 1 | SLEEVE, HYD CYL, TUBE – cylinder |
| 2 | 1255304C1 | 2 | BUSHING, pivot |
| 3 | 1255306C5 | 1 | ROD, PISTON, cylinder, replaces 1255306C4 rod |
| 4 | 238-5139 | 1 | O-RING, -139, 90 Duro, 2.175″ ID x .103″ Thk |
| 5 | 1255309C1 | 1 | SEAL ASSY., piston, cylinder |
| 10 | 119188C1 | 2 | SEAL, piston rod |
| 11 | 238-5143 | 2 | O-RING, -143, 90 Duro, 2.425″ ID x .103″ Thk |
| 12 | 1255311C1 | 2 | WASHER, backup |
| 13 | 1255312C1 | 2 | WIRE, RETAINING, WIRE – retaining, 205 mm (8-1/16 inch) long, cut from 140600C1 bulk wire |
| 14 | D95141 | 2 | WIPER, WIPER – piston rod |
| 15 | 1255310C1 | 2 | CYLINDER HEAD, GLAND – cylinder, end |
| 16 | 219-17 | 2 | NIPPLE, LUBE, 3/16″ x .55″ lg, Drive |
| 1 | 30225R1 | 1 | BOLT, Hex, Lock, M12 x 30, Cl 10.9, BOLT – hex, 12 – 1.75 x 30 mm |
| 2 | 101936C2 | 1 | WASHER, flat, hardened, special, pivot pin to front |
| 4 | 219-41 | 2 | NIPPLE, LUBE, 65є, 1/8″ NPT x 1.20″ lg |
| 5 | 1348230C1 | 1 | PIN, PIVOT, front axle |
| 6 | A177855 | 2 | WASHER, thrust, front axle pivot |
| 8 | 137316A1 | 1 | SUPPORT ASSY., BOLSTER – steering, front axle support, replaces A185918 bolster, see fig. 9-18 for |
| 9 | 192896A1 | 4 | PLUG, front support, if used |
| 1 | 189425C1 | 2 | HUB CAP, wheel hub |
| 2 | 732-6350 | 2 | PIN, SPLIT (COTTER), M6.3 x 50 |
| 3 | 1259683C1 | 2 | NUT, hex, slotted, 30 mm – 1.5, spindle |
| 4 | 896-12030 | 2 | WASHER, M30 x 56.5 x 5, HT, flat, 33 x 56 x 5 mm, hardened |
| 5 | 130504H | 2 | BEARING, CONE, tapered roller, outer |
| 7 | ST753B | 2 | BEARING, CONE, tapered roller, inner |
| 10 | 1259519C2 | 2 | KNUCKLE, STEERING, SPINDLE ASSEMBLY – front wheel |
| 11 | 491641C1 | 1 | SEAL, front wheel spindle |
| 12 | 1259522C1 | 1 | SHIELD, dust, front wheel spindle |
| 13 | 1270815C1 | 2 | BEARING, thrust wheel spindle |
| 14 | 1264574C2 | 1 | EXTENSION ASSY., AXLE – LH section, Incl. item 15 |
| 14 | 1264575C2 | 1 | EXTENSION ASSY., AXLE – RH section, shown |
| 15 | 1259518C1 | 2 | BUSHING, spindle |
| 16 | 1259526C2 | 1 | ARM, steering spindle, left |
| 16 | 1259527C2 | 1 | ARM, STEERING, spindle, right shown |
| 17 | 1259669C2 | 2 | WASHER, steering arm retainer |
| 18 | 614-20055 | 2 | BOLT, Hex, M20 x 55, 8.8, Full Thd |
| 19 | 219-17 | 2 | NIPPLE, LUBE, 3/16″ x .55″ lg, Drive |
| 22 | 828-24200 | 4 | BOLT, Hex, M24 x 200, 10.9 |
| 23 | 896-12024 | 4 | WASHER, M24 x 44.5 x 5, HT, flat, 26 x 44 x 5 mm, hardened |
| 24 | 1264635C1 | 4 | NUT, square, special, axle clamping |
| 25 | 1289100C3 | 1 | AXLE (CENTRE PART), ASSEMBLY – section, center |
| 26 | A177916 | 2 | BUSHING, front pivot |
| 30 | 1259528C1 | 2 | HUB, ASSEMBLY – wheel, front |
| 31 | 1264549C1 | 1 | WASHER, CUP, hub seal |
| 32 | 29214H | 1 | BEARING, CUP, tapered roller, 4-5/16 inch OD, inner, replaces A26744 cup |
| 33 | 130503H | 1 | BEARING, CUP, tapered roller, 3-17/64 inch OD, inner, replaces ST987 cup |
| 34 | 219-404 | 2 | NIPPLE, LUBE, 45є, 3/16″ x .83″ lg, Drive |
| 1 | 1280657C1 | 1 | TUBE, tie rod |
| 3 | 1280658C1 | 1 | BALL JOINT, SOCKET ASSEMBLY – tie rod, end |
| 4 | 1280659C1 | 1 | SEAL, dust |
| 5 | 1280660C1 | 1 | NUT, SLOTTED, hex slotted, 20 mm – 1.50 |
| 6 | 1280661C1 | 1 | NUT, SLOTTED, hex, jam, 1-1/8″ inch NF |
| 7 | 1280662C1 | 1 | BALL JOINT, SOCKET ASSEMBLY – tie rod |
| 8 | 1280659C1 | 1 | SEAL, dust |
| 9 | 1280660C1 | 1 | NUT, SLOTTED, hex slotted, 20 mm – 1.50 |
| 10 | A145857 | 4 | CLAMP, tie rod, replaces A43369 clamp |
| 11 | 328-648 | 2 | BOLT, Hex, 3/8″-24 x 3″, G8 |
| 12 | 232-4616 | 2 | NUT, LOCK, 3/8″-24, GC |
| 13 | 219-8 | 2 | NIPPLE, LUBE, 1/4″-28 NPT x .54″ lg |
| 14 | 432-824 | 4 | PIN, SPLIT (COTTER), 1/8″ x 1 1/2″ |
| 16 | 93194C8 | 1 | CYLINDER STEERING, ASSEMBLY – 67 (2-5/8) ID x 246 mm (9-3/4 inch) stroke, parts list fig. 5-24 |
| 19 | 413-732 | 1 | BOLT, Hex, 7/16″-14 x 2″, G5, BOLT – hex, 7/16 NC x 2 inch, replaces 413-632 bolt, 3/8 x 2 inch, if used |
| 20 | 231-4117 | 1 | NUT, LOCK, 7/16″-14, GB, hex, self-locking, 7/16 inch NC, replaces 131-463 nut, 3/8 inch NC, if used |
| 21 | 219-8 | 1 | NIPPLE, LUBE, 1/4″-28 NPT x .54″ lg |
| 23 | 413-728 | 1 | BOLT, Hex, 7/16″-14 x 1 3/4″, G5 |
| 24 | 232-4117 | 1 | NUT, LOCK, 7/16″-14, GC |
| 27 | 495-81074 | 1 | WASHER, 1 1/32″ x 1 3/4″ x .120″, Flat |
| 28 | 25-1914 | 1 | NUT, SLOTTED, 7/8″-14, G5, Thk, hex, slotted, 7/8 inch NF |
| 29 | 32-1028 | 1 | PIN, SPLIT (COTTER), 5/32″ x 1 3/4″ |
| 31 | 1259579C5 | 1 | ARM, ASSEMBLY – center, steering |
| 32 | 1259581C1 | 2 | BUSHING, center, steering arm |
| 33 | 219-17 | 1 | NIPPLE, LUBE, 3/16″ x .55″ lg, Drive |
| 34 | 238-5214 | 2 | O-RING, -214, 70 Duro, .984″ ID x .139″ Thk |
| 37 | 1334694C1 | 1 | PIN, AXLE, pivot, center arm |
| 38 | 38-31624 | 1 | PIN, ROLL, 1/4″ x 1 1/2″, Coiled, Replaces 19534R1 pin |
| 40 | 1259582C3 | 2 | FITTING, cap, trunnion |
| 41 | 396-31081 | 2 | WASHER, 13/16″ x 1 1/2″ x .219″, HDN |
| 42 | 628-20060 | 2 | BOLT, Hex, M20 x 60, 10.9, Full Thd |
| 1 | 806-12030 | 1 | BOLT, Hex, Lock, M12 x 30, Cl 10.9, BOLT – hex, locking, 12 – 1.75 x 30 mm |
| 2 | 101936C2 | 1 | WASHER, flat, hardened, special, support pin |
| 4 | 219-41 | 2 | NIPPLE, LUBE, 65є, 1/8″ NPT x 1.20″ lg |
| 5 | 1348230C1 | 1 | PIN, PIVOT, front axle |
| 6 | A177855 | 2 | WASHER, thrust, axle pivot |
| 8 | 137316A1 | 1 | SUPPORT ASSY., BOLSTER – steering, front axle support, replaces A185918 bolster, see fig.9-18 for |
| 10 | A177916 | 2 | BUSHING, front pivot |
| 12 | 192896A1 | 4 | PLUG, front support, if used |
| 1 | 1961740C1 | 1 | AXLE (CENTRE PART), HOUSING ASSEMBLY – front axle |
| 2 | 37-1816 | 2 | DOWEL, 1/2″ x 1″, PIN – 1/2 x 1 inch, hardened, replaces 19904R1 pin |
| 3 | 78787C1 | 1 | BREATHER, axle housing |
| 4 | 1969527C1 | 2 | PLATE ASSY., stop, front axle |
| 5 | 326-832 | 4 | BOLT, Hex, 1/2″-13 x 2″, G8 |
| 6 | 221-887 | 2 | PLUG, square socket, 3/4 inch PT, replaces 273469 plug |
| 9 | 1961734C1 | 1 | DIFFERENTIAL, CARRIER ASSEMBLY – front axle, 123480A1 or 197318A1 axle assembly, parts list |
| 9 | 128926A1 | 1 | DIFFERENTIAL, CARRIER ASSEMBLY – front axle, 197320A1 axle assembly, parts list fig. 5-40 |
| 10 | 326-824 | 14 | BOLT, Hex, 1/2″-13 x 1 1/2″, G8, Full Thd |
| 11 | 896-11012 | 14 | WASHER, M13.5 x 24.5 x 3, HT |
| 12 | 128867A1 | 1 | KNUCKLE, STEERING, ASSEMBLY – left-hand, includes item 13 |
| 12 | 128875A1 | 1 | KNUCKLE, STEERING, ASSEMBLY – right-hand, shown |
| 13 | 1961754C1 | 1 | BUSHING, spindle |
| 14 | 128647A1 | 1 | SEAL, oil, 1-9/16 x 2-1/8 x 1/2 inch, no longer included with knuckle assembly, order 193075A2 seal kit |
| 18 | 118660A1 | 2 | TIE ROD, stop, steering |
| 19 | 136-164 | 2 | PIN, SPLIT (COTTER), Int, 5/16″ x .120″, cotter, hair, 5/16 x 2-25/32 inch, if used |
| 20 | 427-12267 | 2 | PIN, CLEVIS, 3/4″ x 2.672″, clevis, 3/4 x 2-43/64 inch, replaces 20243R1 pin |
| 22 | 1342940C1 | 1 | BOOT, dust, ball joint |
| 23 | 432-824 | 1 | PIN, SPLIT (COTTER), 1/8″ x 1 1/2″ |
| 24 | 429-1314 | 1 | NUT, SLOTTED, 7/8″-14, G8, hex, slotted, 7/8 inch NF, grade 8 |
| 25 | 128591A1 | 1 | NUT, hex, special, left-hand thread |
| 26 | 128642A1 | 1 | TUBE, ROD – tie, front axle |
| 27 | 128589A1 | 1 | NUT, hex, special, right-hand thread |
| 29 | 1342940C1 | 1 | BOOT, dust, ball joint |
| 30 | 432-824 | 1 | PIN, SPLIT (COTTER), 1/8″ x 1 1/2″ |
| 31 | 429-1314 | 1 | NUT, SLOTTED, 7/8″-14, G8, hex, slotted, 7/8 inch NF, grade 8 |
| 33 | 326-824 | 16 | BOLT, Hex, 1/2″-13 x 1 1/2″, G8, Full Thd |
| 34 | 896-11012 | 16 | WASHER, M13.5 x 24.5 x 3, HT |
| 35 | 219-10 | 4 | NIPPLE, LUBE, 1/4″-28 NPT x .68″ lg, FITTING – grease, straight, 1/4-28 taper x 11/16 inch, used with |
| 36 | 1277406C1 | 4 | PIN, LARGE, CAP – king pin, if used, replaced by 1277406C2 cap |
| 38 | 1277271C1 | 4 | RETAINER, grease |
| 39 | 671033R1 | 4 | BEARING SET |
| 40 | 671032R1 | 4 | BEARING, CONE |
| 41 | 1277270C1 | 4 | SEAL, OIL, king pin |
| 42 | 185760A1 | 1 | SEAL, lip, oil |
| 44 | 128647A1 | 1 | SEAL, oil, 1-9/16 x 2-1/8 x 1/2 inch |
| 45 | B17069 | 1 | LOCTITE, Hi Strength, No. 601, 2 oz (50 ml), not shown |
| 1 | 1961775C1 | 1 | SHAFT, ASSEMBLY – axle, left, includes items 1-5 |
| 1 | 1968286C1 | 1 | SHAFT ASSY., axle, right, shown |
| 5 | A76014 | 1 | SEAL, oil |
| 6 | 1997795C1 | 1 | SHIN, RETAINER – axle |
| 10 | 133137C91 | 1 | KIT, cross, bearing, replaces 1961778C1 bearing assembly |
| 13 | 1961777C1 | 2 | YOKE, center, front axle |
| 14 | 1961798C1 | 2 | YOKE, ASSEMBLY – outer, front axle |
| 15 | 1961753C1 | 1 | SEAL, yoke, inner |
| 16 | 1277405C1 | 1 | RING, retaining |
| 17 | 1287608C1 | 1 | SEAL, yoke, outer, no longer available, order 193075A2 Sunshaft seal kit |
| 18 | 185760A1 | 1 | SEAL, lip, oil |
| 20 | 128647A1 | 1 | SEAL, oil, 1-9/16 x 2-1/8 x 1/2 inch |
| 21 | 235628A1 | 1 | BUSHING, spindle, see fig. 5-34, item 13 |
| 22 | B17069 | 1 | LOCTITE, Hi Strength, No. 601, 2 oz (50 ml), not shown |
| 23 | 326-624 | 6 | BOLT, Hex, 3/8″-16 x 1 1/2″, G8 |
| 24 | 396-21041 | 6 | WASHER, 13/32″ x 13/16″ x .09″, HDN, flat, 13/32 x 13/16 x 3/32 inch, hardened, replaces 25896R1 |
| 3 | 896-12016 | 4 | WASHER, M17.5 x 30 x 4, HT, flat, 17.5 x 30 x 4 mm, hardened |
| 4 | 434320R1 | 4 | BOLT, Hex, 5/8″-18 x 3 3/4″, G8, hex, 5/8 NF x 3-3/4 inch grade 8 |
| 21 | 1997853C1 | 8 | BOLT, BOLT – special, differential case |
| 25 | H136416 | 12 | SCREW, BOLT – hex head, replaces 1287668C1 bolt |
| 26 | H224501 | 1 | WASHER, flat, special, 7/8 inch, replaces 912716R1 washer |
| 27 | 232-46114 | 1 | NUT, LOCK, 7/8″-14, GC, (Replaces 912726R1) |
| 28 | N9847 | 1 | SPACER, pinion gear, pinion, replaces 1969538C1 spacer |
| 32 | 1968297C1 | 1 | BEARING, CUP, tapered roller |
| 33 | 1968296C1 | 1 | BEARING, CONE, tapered roller |
| 34 | 1968289C1 | 1 | BEARING, CUP, tapered roller |
| 35 | 1968288C1 | 1 | BEARING, CONE, tapered roller |
| 38 | 912712R1 | 1 | WASHER, pinion oil seal |
| 42 | H758326 | 1 | SEAL ASSY., oil, pinion shaft, replaces 1277230C1 seal |
| 43 | 345427C1 | 1 | SLINGER, RING – dust shield |
| 44 | 1961747C1 | 1 | YOKE, YOKE – pinion shaft |
| 45 | 1968291C1 | 2 | BEARING, CONE – tapered roller, differential mounting |
| 46 | 1968292C1 | 2 | BEARING, CUP – tapered roller, 4-1/8 inch OD, differential mounting |
| 47 | 1277233C1 | 2 | RING, differential bearing adjust |
| 48 | 1277234C1 | 2 | CLEVIS, bearing adjusting ring |
| 49 | 396-21034 | 2 | WASHER, .344″ x 11/16″ x .089″, HDN, flat, 11/32 x 11/16 x 3/32 inch, hardened, replaces 27326R1 |
| 50 | 326-512 | 2 | BOLT, Hex, 5/16″-18 x 3/4″, G8, Full Thd |
| 1 | 128648A1 | 2 | SEAL, oil, wheel hub |
| 2 | 1277343C1 | 2 | BEARING, CONE, tapered roller, inner |
| 3 | 1277344C1 | 2 | BEARING, CUP, tapered roller, inner |
| 4 | 1944402C1 | 2 | HUB, front wheel, remanufactured |
| 4 | 1944403C1 | 2 | HUB ASSY., front wheel, return number, use this part number to return hub for credit when using a |
| 4 | 1349338C1 | 2 | HUB, front wheel, new, front |
| 5 | 1997468C1 | 20 | STUD, BOLT – wheel, 3/4 inch NF |
| 7 | L33732 | 2 | CUP ASSY., tapered roller bearing, outer |
| 8 | L33737 | 2 | BEARING, CONE, tapered rolle, outer |
| 10 | 1349339C1 | 2 | SEAL, V-ring |
| 12 | 1277250C1 | 2 | GEAR, RING, planetary ring |
| 14 | 1981278C1 | 2 | PLATE, LARGE, retaining, planet carrier |
| 15 | 326-720 | 12 | BOLT, Hex, 7/16″-14 x 1 1/4″, G8 |
| 16 | 1961770C1 | 2 | GEAR, sun, planetary drive |
| 19 | 102-12175 | 3 | RING, SNAP, #175, 1.673″, Ext Spiral, external spiral retaining, No. 175, replaces 28606R1 ring |
| 20 | 1342869C1 | 1 | SPACER, flat |
| 21 | 78831C1 | 476 | NEEDLE, BEARING |
| 22 | 1277371C1 | 3 | SPACER, bearing |
| 23 | 1349038C1 | 3 | PINION, GEAR – planetary |
| 24 | 1342867C1 | 1 | FLANGE ASSY, CARRIER – planetary gears |
| 26 | 221-667 | 1 | PLUG, DRAIN, Hex Soc, 1/2″ NPT, square socket, magnetic, 1/2 inch PT, replaces 444667 plug |
| 27 | 61-3258 | 4 | SCREW, Hex Soc Hd, 1/4″-20 x 1/2″, BOLT – hex socket, 1/4 NC x 1/2 inch |
| 28 | 1280579C1 | 20 | NUT, hex flange, wheel |
| 2 | 1282023C1 | 1 | NUT, hex lock, cylinder rod |
| 3 | 1277263C1 | 1 | PISTON, cylinder, no longer available, order 197267A1 upgrade kit, see below |
| 15 | 1971565C1 | 1 | ROD, PISTON, cylinder, right (Shown) no longer available, order 194249A1 cylinder assembly on fig. |
| 15 | 1277264C1 | 1 | ROD, cylinder, left, no longer available, order 194247A1 cylinder assembly on fig. 5-48 |
| 18 | 1277265C1 | 1 | CAP CYLINDER END, GLAND – cylinder, no longer available, order 197267A1 upgrade kit, see below |
| 19 | 219-36 | 1 | NIPPLE, LUBE, 45є, 1/8″ NPT x 7/8″ lg |
| 20 | 429-1314 | 1 | NUT, SLOTTED, 7/8″-14, G8, hex, slotted, 7/8 inch NF, grade 8 |
| 21 | 432-824 | 1 | PIN, SPLIT (COTTER), 1/8″ x 1 1/2″ |
| 25 | 1277261C1 | 2 | BALL JOINT, ASSEMBLY – cylinder |
| 26 | 219-36 | 1 | NIPPLE, LUBE, 45є, 1/8″ NPT x 7/8″ lg |
| 27 | 429-1314 | 1 | NUT, SLOTTED, 7/8″-14, G8, hex, 7/8 inch NF, grade 8 |
| 28 | 432-824 | 1 | PIN, SPLIT (COTTER), 1/8″ x 1 1/2″ |
| 29 | 414-1044 | 2 | BOLT, Hex, 5/8″-18 x 2 3/4″, G5, BOLT – hex, 5/8 NF x 2-3/4 inch |
| 30 | 492-11062 | 2 | WASHER, LOCK, 5/8″ |
| 31 | 425-1110 | 2 | NUT, 5/8″-18, G5 |
| 2 | 1282023C1 | 1 | NUT, hex lock, cylinder rod |
| 3 | 194251A1 | 1 | PISTON, cylinder |
| 15 | 194253A1 | 1 | ROD, PISTON, cylinder, right-hand (Shown) |
| 15 | 194252A1 | 1 | ROD, PISTON, cylinder, left-hand |
| 18 | 194250A1 | 1 | CAP CYLINDER END, GLAND – cylinder, no longer available, order either 277765A1 left-hand steering |
| 19 | 219-36 | 1 | NIPPLE, LUBE, 45є, 1/8″ NPT x 7/8″ lg |
| 20 | 429-1314 | 1 | NUT, SLOTTED, 7/8″-14, G8, hex, 7/8 inch NF, grade 8 |
| 21 | 432-824 | 1 | PIN, SPLIT (COTTER), 1/8″ x 1 1/2″ |
| 25 | 1277261C1 | 2 | BALL JOINT, ASSEMBLY – cylinder |
| 26 | 219-36 | 1 | NIPPLE, LUBE, 45є, 1/8″ NPT x 7/8″ lg |
| 27 | 429-1314 | 1 | NUT, SLOTTED, 7/8″-14, G8, hex, 7/8 inch NF, grade 8 |
| 28 | 432-824 | 1 | PIN, SPLIT (COTTER), 1/8″ x 1 1/2″ |
| 29 | 414-1044 | 2 | BOLT, Hex, 5/8″-18 x 2 3/4″, G5, BOLT – hex, 5/8 NF x 2-3/4 inch |
| 30 | 492-11062 | 2 | WASHER, LOCK, 5/8″ |
| 31 | 425-1110 | 2 | NUT, 5/8″-18, G5 |
| 1 | 1270630C1 | 2 | RIM, front, W10L x 16, for 11.00 x 16 12 ply tire |
| 2 | 403538R2 | 16 | SCREW, BOLT – guide wheel |
| 3 | 1270629C1 | 2 | RIM, front, W11L x 16.1, for 14L x 16.1 10 ply tire |
| 3 | 1270628C1 | 2 | RIM, front, W14L x 16.1, for 16.5L x 16.1 8 ply tire |
| 5 | 1342033C1 | 16 | BOLT, BOLT – hex flange special |
| 6 | A38261 | 2 | VALVE, stem, tire inflation, tubeless |
| 8 | 1259528C1 | 2 | HUB, ASSEMBLY – wheel, front, parts list fig. 5-28 |
| 1 | A185508 | 1 | RIM |
| 3 | 1334431C1 | 1 | DISC, wheel (5-1/4 inch offset) |
| 4 | 133-3 | 8 | BOLT, CARRIAGE, Short NK, 5/8″-11 x 3 1/4″, G5 |
| 5 | 495-21069 | 8 | WASHER, 5/8″, flat, 11/16 x 1-3/4 x 9/64 inch |
| 6 | 131-942 | 8 | NUT, Flg, 5/8″-11, G5, large hex flange, 5/8 inch NC |
| 1 | 1334499C1 | 1 | RIM |
| 3 | 1334555C1 | 1 | DISC, wheel (5-1/4 inch offset) |
| 4 | 133-3 | 8 | BOLT, CARRIAGE, Short NK, 5/8″-11 x 3 1/4″, G5 |
| 5 | 495-21069 | 8 | WASHER, 5/8″, flat, 11/16 x 1-3/4 x 9/64 inch |
| 6 | 131-942 | 8 | NUT, Flg, 5/8″-11, G5, large hex flange, 5/8 inch NC |
| 1 | A185509 | 1 | RIM |
| 3 | 1334431C1 | 1 | DISC, wheel (5-1/4 inch offset) |
| 4 | 133-3 | 8 | BOLT, CARRIAGE, Short NK, 5/8″-11 x 3 1/4″, G5 |
| 5 | 495-21069 | 8 | WASHER, 5/8″, flat, 11/16 x 1-3/4 x 9/64 inch |
| 6 | 131-942 | 8 | NUT, Flg, 5/8″-11, G5, large hex flange, 5/8 inch NC |
| 1 | 120264A1 | 1 | RIM |
| 3 | 1334431C1 | 1 | DISC, wheel (5-1/4 inch offset) |
| 4 | 133-3 | 8 | BOLT, CARRIAGE, Short NK, 5/8″-11 x 3 1/4″, G5 |
| 5 | 495-21069 | 8 | WASHER, 5/8″, flat, 11/16 x 1-3/4 x 9/64 inch |
| 6 | 131-942 | 8 | NUT, Flg, 5/8″-11, G5, large hex flange, 5/8 inch NC |
| 1 | A185510 | 1 | RIM |
| 3 | 1334430C1 | 1 | DISC, wheel (4-1/4 inch offset) |
| 4 | 133-3 | 8 | BOLT, CARRIAGE, Short NK, 5/8″-11 x 3 1/4″, G5 |
| 5 | 495-21069 | 8 | WASHER, 5/8″, flat, 11/16 x 1-3/4 x 9/64 inch |
| 6 | 131-942 | 8 | NUT, Flg, 5/8″-11, G5, large hex flange, 5/8 inch NC |
| 1 | 1978525C1 | 1 | RIM |
| 3 | 1334555C1 | 1 | DISC, wheel (5-1/4 inch offset) |
| 4 | 133-3 | 8 | BOLT, CARRIAGE, Short NK, 5/8″-11 x 3 1/4″, G5 |
| 5 | 495-21069 | 8 | WASHER, 5/8″, flat, 11/16 x 1-3/4 x 9/64 inch |
| 6 | 131-942 | 8 | NUT, Flg, 5/8″-11, G5, large hex flange, 5/8 inch NC |
| 1 | 93356C5 | 1 | HOUSING, ASSEMBLY – clutch, replaces 93356C3 and 93356C4 housing |
| 2 | 217-442 | 2 | PLUG, Hex Soc, 3/4″-14, hex socket headless, 3/4 inch PT, if used |
| 2 | 192792A1 | 2 | PLUG, square countersunk, 3/4-14 inch thread, if used |
| 3 | 837-12030 | 2 | DOWEL, M12 x 30, Locating |
| 4 | 30357R1 | 1 | PLUG, M50, Tapered, tapered cup, 50 mm, without MFD |
| 6 | 1981205C1 | 1 | COVER, lube |
| 10 | 628-10025 | 4 | BOLT, Hex, M10 x 25, 10.9, Full Thd |
| 16 | 131165A1 | 1 | FITTING, lube |
| 17 | 237-6010 | 1 | O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk |
| 18 | 238-6016 | 1 | O-RING, -016, 90 Duro, .614″ ID x .070″ Thk |
| 20 | 201-401 | 1 | TEE, 11/16″-16 x 9/16″-18 Br, ORFS, 9/16-18 adj O-ring boss branch x 11/16-16 inch face seal x face |
| 22 | 238-6012 | 2 | O-RING, -012, 90 Duro, .364″ ID x .070″ Thk |
| 25 | 93105C1 | 1 | UNION, ADAPTER – bulkhead, 13/16-16 face x 3/4-16 inch O-ring, with creeper |
| 26 | 238-6014 | 1 | O-RING, -014, 90 Duro, .489″ ID x .070″ Thk |
| 27 | 237-6008 | 1 | O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk, Boss end |
| 28 | 214389 | 1 | PLUG, Hex Hd, 3/4″-16 ORB, Without creeper |
| 29 | 237-6008 | 1 | O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk |
| 31 | 38834 | 1 | BEARING, ROLLER, needle, replaces 220304R1 bearing |
| 32 | 628-20060 | 1 | BOLT, Hex, M20 x 60, 10.9, Full Thd |
| 33 | 896-12020 | 1 | WASHER, M20 x 37.5 x 4, HT, flat, 22 x 37 x 4 mm, hardened |
| 34 | 813-16055 | 9 | BOLT, Hex, M16 x 55,8.8, Bolt, Hex, M16 x 55, 8.8 |
| 35 | 896-11016 | 9 | WASHER, M17.5 x 30 x 4, HT |
| 46 | 76349 | 3 | PLUG, Hex Hd, 9/16″-18 ORB |
| 48 | 218-5158 | 1 | PLUG, Hex Hd, 1 1/16″-12 ORB, hex, 1-1/16-12 inch O-ring boss |
| 49 | 237-6012 | 1 | O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk |
| 61 | 1994583C2 | 1 | GASKET, body plate to mounting plate, see fig. 6-26 |
| 62 | 144143C2 | 1 | GASKET, mounting plate to clutch housing, see fig. 6-26 |
| 63 | 1994609C2 | 1 | PLATE, LARGE, ASSEMBLY – mounting, transmission control valve, parts list fig. 6-26 |
| 64 | 814-10055 | 4 | BOLT, Hex, M10 x 55, 8.8 |
| 65 | 863-10040 | 1 | SCREW, Hex Soc Hd, M10 x 40, 12.9, BOLT – hex socket, 10 – 1.5 x 40 mm, class 12.9 |
| 66 | 1286093C3 | 1 | RETAINER, tube |
| 67 | 1963936C1 | 2 | TUBE, first, second, third and fourth speed, steel |
| 68 | 1963937C1 | 1 | TUBE, fifth and sixth speed, steel |
| 69 | 1963938C1 | 1 | TUBE, reverse, steel |
| 70 | 238-6016 | 8 | O-RING, -016, 90 Duro, .614″ ID x .070″ Thk |
| 73 | 1286090C1 | 1 | TUBE, clutch, front low |
| 74 | 1286091C1 | 1 | TUBE, clutch, front medium |
| 75 | 1286092C1 | 1 | TUBE, clutch, front high |
| 76 | 238-6212 | 3 | O-RING, -212, 90 Duro, .859″ ID x .139″ Thk |
| 77 | 863-10040 | 1 | SCREW, Hex Soc Hd, M10 x 40, 12.9, BOLT – hex socket, 10 – 1.5 x 40 mm, class 12.9 |
| 21 | 237-6006 | 1 | O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk |
| 47 | 237-6006 | 1 | O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk |
| 1 | 1997440C1 | 1 | SHAFT ASSY., input |
| 3 | 1286085C1 | 2 | PIN, LARGE, dowel |
| 4 | 1963888C1 | 2 | PIN, slotted spring |
| 5 | 38-3605 | 4 | PIN, 3/32″ x 5/16″, Coiled |
| 8 | 93304C2 | 1 | HOUSING, CLUTCH, CARRIER |
| 9 | 93350C1 | 6 | RING, retaining, external |
| 10 | 1286081C1 | 2 | O-RING, piston, low clutch inner |
| 11 | 1286076C1 | 2 | RING, piston, clutch |
| 12 | 1285998C1 | 2 | PISTON, clutch, shift |
| 13 | 1286083C1 | 2 | O-RING, piston, low clutch outer |
| 14 | 1286079C1 | 2 | RING, piston, shift |
| 18 | 93129C1 | 6 | WASHER, Belleville spring cushion, clutch |
| 19 | 93190C1 | 2 | DISC, reaction, spring |
| 20 | 92935C5 | 10 | DISC, friction |
| 21 | 92934C2 | 8 | DISC, separator, clutch |
| 22 | 1342854C2 | 2 | DISC, backing, clutch, 16.45 mm thick, replaces 1342854C1 disc |
| 23 | 1285996C1 | 2 | RING, SNAP, retaining, plate |
| 24 | 1286012C2 | 26 | WASHER, Belleville spring, piston return |
| 25 | 1286043C1 | 6 | WASHER, THRUST, bearing |
| 28 | 572182R1 | 3 | BEARING, THRUST, needle |
| 29 | 80907C1 | 2 | BEARING, NEEDLE, caged |
| 30 | 93297C1 | 1 | SPACER, bearing, input |
| 31 | 1342495C1 | 1 | GEAR, DRIVEN, GEAR – second, fourth and sixth, 37 teeth |
| 32 | 1286052C1 | 2 | RING, seal, clutch |
| 33 | 1286042C1 | 2 | WASHER, THRUST, bearing |
| 36 | K620185 | 1 | BEARING, THRUST, needle, thrust |
| 38 | 1285985C1 | 1 | GEAR, WHEEL, odd/even clutch and fifth, 34 teeth |
| 39 | 1286016C1 | 1 | BEARING, NEEDLE, caged |
| 40 | 1286039C1 | 2 | SPACER, bearing |
| 41 | 364465C1 | 1 | BEARING, CONE, tapered roller |
| 42 | 258452C1 | 1 | BEARING, CUP, tapered roller |
| 43 | 1286026C1 | 5 | RING, seal, input shaft |
| 44 | 1981213C1 | 1 | CAGE, bearing, input |
| 48 | 613-10030 | 4 | BOLT, Hex, M10 x 30, 8.8, Full Thd, BOLT – hex, full threads, 10 – 1.5 x 30 mm |
| 50 | 1981207C1 | 1 | TUBE, lube |
| 52 | 627639R1 | 1 | BEARING, CONE, tapered roller |
| 53 | ST970 | 1 | BEARING, CUP, tapered roller |
| 54 | 1997371C1 | 1 | SEAL, shaft, input |
| 55 | 1286118C2 | 1 | SUPPORT ASSY., bearing, front |
| 56 | 20229R1 | 8 | DOWEL, 1/2″ x 1/2″, dowel, 1/2 x 1/2 inch |
| 57 | 615-12040 | 11 | BOLT, Hex, M12 x 40, 8.8, Full Thd, BOLT – hex, full threads, 12 – 1.75 x 40 mm, replaces 30044R1 |
| 60 | 1342447C1 | 1 | COUPLING, SPLINED, shaft input |
| 61 | 1342448C1 | 1 | SHAFT, driven, damper |
| 1 | 1963894C1 | 1 | SHAFT, ASSEMBLY – input |
| 3 | 1286085C1 | 4 | PIN, LARGE, dowel |
| 4 | 1963888C1 | 2 | PIN, slotted spring |
| 5 | 38-3605 | 5 | PIN, 3/32″ x 5/16″, Coiled |
| 8 | 93304C2 | 1 | HOUSING, CLUTCH, CARRIER – fifth and reverse |
| 9 | 93350C1 | 6 | RING, retaining, external |
| 10 | 1286081C1 | 2 | O-RING, piston, low clutch inner |
| 11 | 1286076C1 | 2 | RING, piston, clutch |
| 12 | 1285998C1 | 2 | PISTON, clutch, shift |
| 13 | 1286083C1 | 2 | O-RING, piston, low clutch outer |
| 14 | 1286079C1 | 2 | RING, piston, shift |
| 18 | 93129C1 | 6 | WASHER, Belleville spring, cushion, clutch |
| 19 | 93190C1 | 2 | DISC, reaction, spring |
| 20 | 92935C5 | 10 | DISC, friction |
| 21 | 92934C2 | 8 | DISC, separator, clutch |
| 22 | 1342854C2 | 2 | DISC, backing, clutch, 16.45 mm thick, replaces 1342854C1 disc |
| 23 | 1285996C1 | 2 | RING, SNAP, retaining, plate |
| 24 | 1286012C2 | 26 | WASHER, Belleville spring, piston return |
| 25 | 1286043C1 | 6 | WASHER, THRUST, bearing |
| 28 | 572182R1 | 3 | BEARING, THRUST, needle |
| 29 | 80907C1 | 2 | BEARING, NEEDLE, caged |
| 30 | 93297C1 | 1 | SPACER, bearing, input |
| 31 | 1342495C1 | 1 | GEAR, DRIVEN, GEAR – second, fourth and sixth, 37 teeth |
| 32 | 1286052C1 | 2 | RING, seal, clutch |
| 33 | 1286042C1 | 2 | WASHER, THRUST, bearing |
| 36 | K620185 | 1 | BEARING, THRUST, needle, thrust |
| 37 | 92793C1 | 1 | RING, retaining, external |
| 38 | 1285985C1 | 1 | GEAR, WHEEL, odd/even clutch and fifth, 34 teeth, odd/even clutch and fifth |
| 39 | 1286016C1 | 1 | BEARING, NEEDLE, caged |
| 40 | 1286039C1 | 2 | SPACER, bearing |
| 41 | 364465C1 | 1 | BEARING, CONE, tapered roller |
| 42 | 258452C1 | 1 | BEARING, CUP, tapered roller |
| 43 | 1286026C1 | 5 | RING, seal, input shaft |
| 44 | 1981213C1 | 1 | CAGE, bearing, input |
| 48 | 613-10030 | 4 | BOLT, Hex, M10 x 30, 8.8, Full Thd, BOLT – hex, full threads, 10 – 1.5 x 30 mm |
| 50 | 1981207C1 | 1 | TUBE, lube |
| 52 | L33289 | 1 | BEARING, CONE, tapered roller, 2-1/4 inch ID, replaces 659458R1 cone |
| 53 | 105497H | 1 | BEARING, CUP, tapered roller |
| 54 | 108935A1 | 1 | SEAL, shaft, input, replaces 92840C1 seal |
| 55 | 92837C2 | 1 | SUPPORT ASSY., bearing, front |
| 56 | 20229R1 | 8 | DOWEL, 1/2″ x 1/2″, dowel, 1/2 x 1/2 inch |
| 57 | 615-12040 | 11 | BOLT, Hex, M12 x 40, 8.8, Full Thd, BOLT – hex, full threads, 12 – 1.75 x 40 mm, replaces 30044R1 |
| 58 | 92794C1 | 1 | PINION, GEAR – creeper |
| 60 | 92841C1 | 1 | COUPLING, SPLINED, shaft input |
| 64 | 218-5103 | 1 | ELBOW, 90є, 7/16″-20, 37є x 7/16″-20, O-Ring, 90 degree, 7/16-20 inch flare x adj O-ring boss |
| 65 | 237-6004 | 1 | O-RING, 4-1, 90 Duro, .351″ ID x .072″ Thk |
| 66 | 92836C1 | 1 | PIPE, TUBE – supply, lube |
| 67 | 108932A1 | 1 | O-RING, O-RING – 40.87 ID x 3.53 mm wide |
| 68 | 108933A1 | 1 | SHAFT, driven, damper, with 4.45 mm wide O-ring groove |
| 1 | 1342253C2 | 1 | SHAFT, counter, replaces 1342253C1 |
| 2 | 100-11293 | 2 | RING, SNAP, #293, Ext, Replaces 304697C1 |
| 4 | 1285983C1 | 1 | GEAR, DRIVING, GEAR – driver, third and fourth, 34 teeth |
| 5 | 211-1012 | 4 | BALL, 3/8″ Dia, chrome alloy steel, 3/8 inch, grade 24, replaces 211-210 ball |
| 7 | ST791 | 1 | BEARING, CONE, tapered roller |
| 8 | ST951 | 1 | BEARING, CUP, tapered roller |
| 11 | 1285981C1 | 1 | PINION, GEAR – driver, first and second, 29 teeth |
| 12 | ST2051 | 1 | BEARING, CONE, tapered roller |
| 13 | ST863 | 1 | BEARING, CUP, tapered roller |
| 14 | 1286000C3 | 1 | CAGE, bearing |
| 18 | 613-10025 | 6 | BOLT, Hex, M10 x 25, 8.8, Full Thd, BOLT – hex, full threads, 10 – 1.5 x 25 mm |
| 20 | 1285989C1 | 1 | PINION, GEAR – driven, second, fourth and sixth, 37 teeth |
| 22 | 1285986C1 | 1 | PINION, GEAR – driven, first, third and fifth, 39 teeth |
| 1 | 1342318C2 | 1 | SHAFT, COUNTER ASSEMBLY – transmission, replaces 1342318C1 |
| 2 | 1286084C1 | 1 | PIN, dowel, 12 x 11 mm |
| 3 | 92825C1 | 1 | PLUG, countershaft |
| 4 | 1963875C1 | 1 | PIN, SPLIT (COTTER), slotted spring |
| 5 | 211-1012 | 4 | BALL, 3/8″ Dia, chrome alloy steel, 3/8 inch, grade 24, replaces 211-210 |
| 7 | 100-11293 | 1 | RING, SNAP, #293, Ext, Replaces 304697C1 |
| 9 | 1285983C1 | 1 | GEAR, DRIVING, GEAR – driver, third and fourth, 34 teeth |
| 10 | 144242C3 | 2 | RING, seal, 33 mm, replaces 148945C2 |
| 11 | 92828C1 | 1 | CAGE, bearing |
| 12 | 613-10025 | 6 | BOLT, Hex, M10 x 25, 8.8, Full Thd, BOLT – hex, full threads, 10 – 1.5 x 25 mm |
| 15 | 218-5057 | 1 | CONNECTOR, HYD., 9/16″-18, 37є x 9/16″-18, O-Ring |
| 17 | 93104C2 | 1 | UNION, bulkhead, replaces 93104C1 |
| 18 | 238-6012 | 1 | O-RING, -012, 90 Duro, .364″ ID x .070″ Thk |
| 19 | 92848C1 | 1 | TUBE, pressure |
| 20 | 92824C1 | 1 | SPACER, carrier |
| 21 | 92797C1 | 1 | HOUSING, CLUTCH, CARRIER |
| 22 | 1286081C1 | 1 | O-RING, piston, low clutch inner |
| 25 | 1286076C1 | 1 | RING, piston, clutch, shift |
| 26 | 1285998C1 | 1 | PISTON, clutch |
| 27 | 1286083C1 | 1 | O-RING, piston, low clutch outer |
| 28 | 1286079C1 | 1 | RING, piston, shift |
| 33 | 93129C1 | 3 | WASHER, Belleville spring, cushion |
| 34 | 93190C1 | 1 | DISC, reaction |
| 35 | 92935C5 | 8 | DISC, friction |
| 36 | 92934C2 | 7 | DISC, separator |
| 37 | 1342645C3 | 1 | DISC, CLUTCH, backing, clutch, 9.7 mm thick |
| 38 | 1285996C1 | 1 | RING, SNAP, retaining |
| 39 | 93350C1 | 2 | RING, retaining, external |
| 40 | 1286012C2 | 13 | WASHER, Belleville spring, piston return |
| 41 | 1286043C1 | 2 | WASHER, THRUST, bearing |
| 42 | 572182R1 | 1 | BEARING, THRUST, needle |
| 43 | 1286052C1 | 1 | RING, seal |
| 51 | 92795C1 | 1 | PINION, GEAR – driven, creeper |
| 52 | 80906C1 | 1 | BEARING, NEEDLE, needle, caged (1-1/4 inch) |
| 53 | 1286042C1 | 2 | WASHER, THRUST, bearing |
| 54 | K620185 | 1 | BEARING, THRUST, needle, thrust |
| 55 | ST2051 | 2 | BEARING, CONE, tapered roller |
| 56 | ST863 | 2 | BEARING, CUP, tapered roller |
| 58 | 1285986C1 | 1 | PINION, GEAR – driven, first, third and fifth, 39 teeth |
| 61 | 1285989C1 | 1 | PINION, GEAR – driven, second, fourth and sixth, 37 teeth |
| 62 | 1285981C1 | 1 | PINION, GEAR – driver, first and second, 29 teeth |
| 16 | 237-6006 | 1 | O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk |
| 18 | 237-6006 | 2 | O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk |
| 1 | 1997444C1 | 1 | SHAFT, ASSEMBLY – output |
| 2 | 1342852C1 | 3 | PLUG, sealing, 12 mm |
| 4 | 38-3605 | 6 | PIN, 3/32″ x 5/16″, Coiled |
| 5 | 1963875C1 | 4 | PIN, SPLIT (COTTER), slotted spring |
| 8 | 1286040C2 | 1 | RING, support, bearing |
| 9 | 1997888C1 | 1 | WASHER, THRUST |
| 10 | 1286016C1 | 1 | BEARING, NEEDLE, caged |
| 11 | 1285985C1 | 1 | GEAR, WHEEL, odd/even clutch and fifth, 34 teeth, speed, fifth and sixth |
| 12 | 1285987C1 | 1 | PINION, GEAR – driven, reverse, 39 teeth |
| 13 | 1286052C1 | 2 | RING, seal, clutch |
| 16 | 1286043C1 | 4 | WASHER, THRUST, bearing |
| 17 | 572182R1 | 2 | BEARING, THRUST, needle |
| 18 | 93350C1 | 4 | RING, retaining, external |
| 19 | 1286012C2 | 24 | WASHER, Belleville spring, return |
| 20 | 93304C2 | 1 | HOUSING, CLUTCH, CARRIER – clutch, fifth and reverse |
| 22 | 1286081C1 | 2 | O-RING, piston, low clutch inner |
| 23 | 1286076C1 | 2 | RING, piston, clutch |
| 24 | 1285998C1 | 2 | PISTON, clutch |
| 25 | 1286083C1 | 2 | O-RING, piston, low clutch outer |
| 26 | 1286079C1 | 2 | RING, piston, shift, clutch |
| 29 | 93129C1 | 3 | WASHER, Belleville spring, cushion |
| 30 | 93190C1 | 2 | DISC, reaction, spring |
| 31 | 92935C5 | 10 | DISC, friction |
| 32 | 92934C2 | 8 | DISC, separator |
| 33 | 1342854C2 | 2 | DISC, backing, clutch, 16.45 mm thick, replaces 1342854C1 disc |
| 34 | 1285996C1 | 2 | RING, SNAP, retaining |
| 35 | 93129C1 | 3 | WASHER, Belleville spring, cushion |
| 36 | 80907C1 | 1 | BEARING, NEEDLE, caged, 1 inch long |
| 37 | 1342513C1 | 1 | SPACER, bearing |
| 39 | 1286042C1 | 2 | WASHER, THRUST, bearing |
| 40 | K620185 | 1 | BEARING, THRUST, needle, thrust |
| 44 | 219530H1 | 1 | BEARING, CONE, tapered roller |
| 45 | ST964 | 1 | BEARING, CUP, tapered roller |
| 46 | 1286024C1 | 4 | RING, seal |
| 47 | 238-5223 | 1 | O-RING, -223, 70 Duro, 1.609″ ID x .139″ Thk, 1-3/4 ID x 1/8 inch wide, master clutch hub |
| 1 | 1997444C1 | 1 | SHAFT, ASSEMBLY – output, see fig. 6-14 for pins and plugs |
| 10 | 1286016C1 | 1 | BEARING, NEEDLE, caged |
| 13 | 1286052C1 | 2 | RING, seal, clutch |
| 16 | 1286043C1 | 4 | WASHER, THRUST, bearing |
| 17 | 572182R1 | 2 | BEARING, THRUST, needle |
| 18 | 93350C1 | 4 | RING, retaining, external |
| 19 | 1286012C2 | 26 | WASHER, Belleville spring, return |
| 21 | 1285970C2 | 1 | HOUSING, CLUTCH, CARRIER – clutch, first and third |
| 22 | 1286081C1 | 2 | O-RING, piston, low clutch inner |
| 23 | 1286076C1 | 2 | RING, piston, clutch |
| 24 | 1285998C1 | 2 | PISTON, clutch |
| 25 | 1286083C1 | 2 | O-RING, piston, low clutch outer |
| 26 | 1286079C1 | 2 | RING, piston, shift, clutch |
| 29 | 93129C1 | 6 | WASHER, Belleville spring, cushion |
| 30 | 93190C1 | 2 | DISC, reaction, spring |
| 31 | 92935C5 | 14 | DISC, friction |
| 32 | 92934C2 | 12 | DISC, separator |
| 33 | 1342854C2 | 2 | DISC, backing, clutch, 16.45 mm thick, replaces 1342854C1 disc |
| 34 | 1285996C1 | 2 | RING, SNAP, retaining |
| 35 | 1285984C1 | 1 | GEAR, GEAR – driven, third and fourth, 39 teeth |
| 37 | 1285982C1 | 1 | GEAR, DRIVEN, GEAR – driven, first and second, 44 teeth |
| 38 | 1285997C1 | 1 | BEARING, NEEDLE, caged |
| 39 | 1286042C1 | 2 | WASHER, THRUST, bearing |
| 40 | K620185 | 1 | BEARING, THRUST, needle, thrust |
| 47 | 1286021C1 | 1 | BEARING, ROLLER, CONE – tapered |
| 48 | 29214H | 1 | BEARING, CUP, tapered roller, 4-5/16 inch OD |
| 49 | 1286001C3 | 1 | CAGE, bearing |
| 51 | 613-10025 | 4 | BOLT, Hex, M10 x 25, 8.8, Full Thd, BOLT – hex, full threads, 10 – 1.5 x 25 mm |
| 1 | 125806A1 | 1 | HOUSING, ASSEMBLY – range, transmission |
| 2 | 837-16035 | 4 | DOWEL, M16 x 35, PIN – 16 x 35 mm, hardened |
| 3 | 837-12025 | 2 | DOWEL, M12 x 25, Hardened |
| 5 | 192792A1 | 1 | PLUG, square countersunk, 3/4 – 14 inch thread |
| 6 | 221-847 | 1 | PLUG, Hex Soc, 1 1/4″-11 1/2, square socket headless, 1-1/4 inch PT, without heater, replaces |
| 7 | 41-1618 | 1 | PLUG, Cup, 1 1/8″, Stainless, cup, 1-1/8 inch diameter, without hitch, replaces 41600D plug |
| 10 | 214389 | 1 | PLUG, Hex Hd, 3/4″-16 ORB, Without MFD |
| 11 | 237-6008 | 1 | O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk |
| 12 | 87390949 | 1 | GASKET, housing |
| 13 | 896-11016 | 12 | WASHER, M17.5 x 30 x 4, HT |
| 14 | 813-16060 | 10 | BOLT, Hex, M16 x 60, 8.8, Full Thd, Bolt, Hex, M16 x 60, 8.8, Full Thd |
| 14 | 814-16070 | 2 | BOLT, Hex, M16 x 70, 8.8 |
| 15 | 92821C2 | 1 | GASKET, housing, axle |
| 16 | 93364C1 | 1 | COVER, access, shift fork |
| 17 | 628-10025 | 12 | BOLT, Hex, M10 x 25, 10.9, Full Thd |
| 20 | 1976744C2 | 1 | COVER ASSY, opening, brake, see fig. 8-48 for adapter and hose |
| 21 | 613-10020 | 4 | BOLT, Hex, M10 x 20, 8.8, Full Thd, BOLT – hex, full threads, 10 – 1.5 x 20 mm |
| 22 | 613-16030 | 2 | BOLT, Hex, M16 x 30, 8.8, Full Thd, Bolt, Hex, M16 x 30, 8.8, Full Thd, used as a plug, if used, may be |
| 23 | 238-5114 | 2 | O-RING, -114, 70 Duro, .612″ ID x .103″ Thk, Used with item 22 bolt, if used, may be replaced by item |
| 24 | 301533R1 | 1 | BEARING, NEEDLE, front, pinion shaft |
| 28 | 1340584C1 | 1 | TUBE, dipstick |
| 29 | 825-1406 | 1 | NUT, M6, Cl 8 |
| 30 | 614-6020 | 1 | BOLT, Hex, M6 x 20, 8.8, Full threads |
| 31 | 1342132C1 | 1 | SUPPORT, BRACKET – dipstick, with hitch |
| 31 | 1342155C1 | 1 | SUPPORT, BRACKET – dipstick, without hitch |
| 32 | 515-21127 | 1 | CLAMP, 1/2″, Insul, 1/4″ Bolt, P-type, Replaces 98959R1 clamp |
| 33 | 1342137C2 | 1 | DIPSTICK, oil level |
| 34 | 1968044C2 | 1 | TUBE, dipstick, internal |
| 35 | 238-6014 | 1 | O-RING, -014, 90 Duro, .489″ ID x .070″ Thk |
| 36 | 605-16020 | 2 | BOLT, Hex, Lock, M16 x 20, Cl 8.8, BOLT – hex, locking, 16 – 2.0 x 20 mm |
| 40 | 536850R1 | 1 | HEATER, ASSEMBLY – oil, transmission, component parts not serviced separately |
| 1 | 124542A1 | 1 | MANIFOLD, lubrication |
| 2 | 145400C2 | 1 | GASKET, manifold |
| 3 | 814-10070 | 4 | BOLT, Hex, M10 x 70, 8.8, BOLT – hex, 10 – 1.5 x 70 mm |
| 6 | 201-101 | 1 | CONNECTOR, HYD., 11/16″-16 ORFS x 9/16″-18 ORB, ADAPTER – straight, 11/16-16 face seal x |
| 7 | 237-6006 | 1 | O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk |
| 8 | 238-6012 | 1 | O-RING, -012, 90 Duro, .364″ ID x .070″ Thk |
| 10 | 201-306 | 1 | ELBOW, 90є, 1″-14 x 7/8″-14 Adj, ORFS, 90 degree, 1-14 face seal x 7/8-14 inch adj O-ring boss |
| 13 | 201-420 | 1 | TEE, 1″-14 x 7/8″-14 Run, ORFS, 1-14 face branch x face x 7/8-14 inch adj O-ring boss, with creeper |
| 14 | 237-6010 | 1 | O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk |
| 15 | 238-6016 | 1 | O-RING, -016, 90 Duro, .614″ ID x .070″ Thk |
| 16 | 201-310 | 1 | ELBOW, 90є, 2″-12 x 1 7/8″-12, Adj, ORFS, 90 degree, 2-12 face x 1-7/8 inch adj O-ring boss |
| 17 | 237-6024 | 1 | O-RING, 24-1, 90 Duro, 1.72″ ID x .118″ Thk |
| 18 | 238-6029 | 1 | O-RING, -029, 90 Duro, 1.489″ ID x .070″ Thk |
| 22 | 1342029C1 | 1 | TUBE, lubrication, odd/even |
| 23 | 1348316C1 | 1 | PIPE, TUBE – lubrication, creeper drive |
| 24 | 131165A1 | 1 | FITTING, lube |
| 25 | 237-6010 | 1 | O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk |
| 26 | 238-6016 | 2 | O-RING, -016, 90 Duro, .614″ ID x .070″ Thk |
| 27 | 1349444C1 | 1 | TUBE, lubrication, draft cylinder |
| 28 | 201-120 | 1 | CONNECTOR, HYD., 11/16″-16, Blkhd, ORFS, straight, 11/16-16 inch face seal x bulkhead face seal |
| 29 | 238-6012 | 1 | O-RING, -012, 90 Duro, .364″ ID x .070″ Thk |
| 33 | 86625138 | 2 | PLUG, Hex Soc, 7/8″-14 ORB |
| 34 | 237-6010 | 1 | O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk |
| 37 | 201-101 | 1 | CONNECTOR, HYD., 11/16″-16 ORFS x 9/16″-18 ORB, ADAPTER – straight, 11/16-16 face seal x |
| 38 | 237-6006 | 1 | O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk |
| 39 | 238-6012 | 1 | O-RING, -012, 90 Duro, .364″ ID x .070″ Thk |
| 40 | 201-103 | 1 | CONNECTOR, HYD., 1″-14 ORFS x 7/8″-14 ORB |
| 41 | 237-6010 | 1 | O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk |
| 42 | 238-6016 | 1 | O-RING, -016, 90 Duro, .614″ ID x .070″ Thk |
| 43 | 9672438 | 1 | PLUG, Hex Hd, 7/16″-20 ORB, W/O hitch |
| 44 | 237-6004 | 1 | O-RING, 4-1, 90 Duro, .351″ ID x .072″ Thk |
| 50 | 1289215C1 | 1 | TUBE, lube main supply |
| 51 | 201-102 | 1 | CONNECTOR, HYD., 13/16″-16 ORFS x 3/4″-16 ORB |
| 52 | 237-6008 | 1 | O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk |
| 53 | 238-6014 | 1 | O-RING, -014, 90 Duro, .489″ ID x .070″ Thk |
| 54 | 201-409 | 1 | TEE, 13/16″-16 ORFS, 13/16-16 inch face seal branch x face seal x face seal |
| 55 | 238-6014 | 3 | O-RING, -014, 90 Duro, .489″ ID x .070″ Thk |
| 56 | 1289214C1 | 1 | TUBE, lube, right-hand brake |
| 57 | 1289212C1 | 1 | TUBE, lube, left-hand brake |
| 58 | 107813A1 | 1 | PIPE, TUBE – lubrication, PTO rear |
| 60 | 201-402 | 1 | TEE, 13/16″-18 x 3/4″-16 Br, ORFS, 3/4-16 adj O-ring branch x 13/16-16 inch face x face |
| 61 | 237-6008 | 1 | O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk |
| 62 | 238-6014 | 2 | O-RING, -014, 90 Duro, .489″ ID x .070″ Thk |
| 70 | 76349 | 1 | PLUG, Hex Hd, 9/16″-18 ORB, without MFD |
| 71 | 237-6006 | 1 | O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk |
| 73 | 1349199C3 | 1 | FITTING, bevel gear and bearing lube, without hitch |
| 74 | 237-6006 | 1 | O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk |
| 75 | 238-6012 | 1 | O-RING, -012, 90 Duro, .364″ ID x .070″ Thk |
| 76 | 1342229C3 | 1 | COVER, housing, rear frame, without hitch |
| 77 | 1971726C1 | 1 | BREATHER, housing |
| 78 | 93103C1 | 1 | UNION, bulkhead, lube |
| 79 | 237-6008 | 1 | O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk |
| 80 | 238-6012 | 1 | O-RING, -012, 90 Duro, .364″ ID x .070″ Thk |
| 81 | 124306A1 | 1 | PIPE, TUBE – lube |
| 82 | 1289222C1 | 1 | PIPE, TUBE – lube, range spray |
| 83 | 201-304 | 1 | ELBOW, 90є, 11/16″-16 x 9/16″-18 Adj, ORFS, 90 degree, 11/16-16 face seal x 9/16-18 inch adj |
| 84 | 237-6006 | 1 | O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk |
| 85 | 238-6012 | 1 | O-RING, -012, 90 Duro, .364″ ID x .070″ Thk |
| 86 | 9625178 | 1 | PLUG, Hex Soc, 9/16″-18 ORB, without hitch |
| 87 | 237-6006 | 1 | O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk |
| 88 | 221-62 | 2 | REDUCER, Hex, 1″ x 1/4″ NPT, reducing pipe, 1 x 1/4, without hitch |
| 89 | 1330639C1 | 1 | FITTING, ADAPTER – straight, 9/16-18 inch O-ring boss, without hitch |
| 90 | 237-6006 | 1 | O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk |
| 91 | 628-16035 | 14 | BOLT, Hex, M16 x 35, 10.9, Full Thd, Bolt, Hex, M16 x 35, 10.9, Full Thd, without hitch |
| 92 | 614-16100 | 2 | BOLT, Hex, M16 x 100, 8.8, Full Thd, BOLT – hex, full threads, 16 – 2.0 x 100 mm, without hitch |
| 1 | 103182A1 | 1 | VALVE, CONTROL, ASSEMBLY – transmission control (Without Creeper), parts list fig’.s 6-28 – 6-38 |
| 1 | 103183A1 | 1 | VALVE, CONTROL, ASSEMBLY – transmission control (With Creeper), parts list fig’.s 6-28- 6-38 |
| 3 | 814-10045 | 3 | BOLT, Hex, M10 x 45, 8.8, See Fig. 6-38 |
| 4 | 828-8120 | 3 | BOLT, Hex, M8 x 120, 10.9, BOLT – hex, 8 – 1.25 x 120 mm, class 10.9, see fig. 6-38 |
| 4 | 828-8140 | 8 | BOLT, Hex, M8 x 140, 10.9, BOLT – hex, 8 – 1.25 x 140 mm, class 10.9, see fig. 6-38, replaces |
| 6 | 814-10175 | 2 | SCREW, BOLT – hex, 10 – 1.5 x 1.75 mm, see fig. 6-38 |
| 12 | 201-306 | 1 | ELBOW, 90є, 1″-14 x 7/8″-14 Adj, ORFS, 90 degree, 1-14 face seal x 7/8-14 inch adj O-ring boss |
| 13 | 237-6010 | 1 | O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk |
| 14 | 238-6016 | 1 | O-RING, -016, 90 Duro, .614″ ID x .070″ Thk |
| 15 | 201-103 | 1 | CONNECTOR, HYD., 1″-14 ORFS x 7/8″-14 ORB |
| 16 | 237-6010 | 1 | O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk |
| 17 | 238-6016 | 1 | O-RING, -016, 90 Duro, .614″ ID x .070″ Thk |
| 20 | 201-101 | 1 | CONNECTOR, HYD., 11/16″-16 ORFS x 9/16″-18 ORB, ADAPTER – straight, 11/16-16 face seal x |
| 21 | 237-6006 | 1 | O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk, Boss end |
| 22 | 238-6012 | 1 | O-RING, -012, 90 Duro, .364″ ID x .070″ Thk, Face end |
| 23 | 1968016C2 | 1 | TUBE, inlet, valve |
| 24 | 1968170C1 | 1 | TUBE, jumper, with creeper |
| 25 | 1342600C2 | 1 | ANCHOR, RETAINER – tube |
| 26 | 1348287C1 | 1 | TUBE, clutch, master |
| 27 | 863-10040 | 1 | SCREW, Hex Soc Hd, M10 x 40, 12.9, BOLT – hex socket, 10 – 1.5 x 40 mm, class 12.9 |
| 28 | 238-7018 | 4 | O-RING, -018, Cl 7, .739″ ID x .070″ Thk |
| 30 | 1349400C1 | 1 | TUBE, clutch, odd |
| 31 | 1349402C1 | 1 | TUBE, clutch, even |
| 32 | H434164 | 1 | COUPLING, quick check |
| 33 | 218-5450 | 1 | ELBOW, 90є, 7/16″-20 ORB x 1/8″ NPT Fem, 90 degree, 7/16-20 O-ring boss x 1/8 inch female PT |
| 34 | 237-6004 | 1 | O-RING, 4-1, 90 Duro, .351″ ID x .072″ Thk |
| 35 | 1348316C1 | 1 | PIPE, TUBE – lubrication, creeper drive |
| 36 | 1981208C1 | 1 | SUPPORT, BRACKET – tube |
| 37 | 864-10025 | 2 | SCREW, Hex Soc Hd, M10 x 25, 8.8, BOLT – hex socket, 10 – 1.5 x 25 mm |
| 1 | 1994583C2 | 1 | GASKET, body plate to mounting plate |
| 2 | 144143C2 | 1 | GASKET, mounting plate to clutch housing |
| 4 | 133519C1 | 1 | SCREEN, filter |
| 5 | 1981235C2 | 1 | PLUG, valve, poppet |
| 6 | 1975424C1 | 1 | SPRING, check valve |
| 7 | 1975438C1 | 1 | VALVE, check |
| 8 | 86529630 | 2 | PLUG, Hex Soc, 3/8″-24 ORB |
| 10 | 47-212 | 1 | RIVET, FH, 1/8″ x 3/4″, flat head steel, 1/8 x 3/4 inch |
| 11 | 511-1060 | 1 | BALL, 6mm Dia, 6 mm, grade 28, chrome alloy steel, replaces 30935R1 ball |
| 12 | 76349 | 3 | PLUG, Hex Hd, 9/16″-18 ORB |
| 14 | 814-10055 | 4 | BOLT, Hex, M10 x 55, 8.8 |
| 15 | 863-10040 | 1 | SCREW, Hex Soc Hd, M10 x 40, 12.9, BOLT – hex socket, 10 – 1.5 x 40 mm, class 12.9 |
| 9 | 237-6006 | 1 | O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk |
| 13 | 237-6006 | 1 | O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk |
| 1 | 1994675C2 | 1 | HOUSING, ASSEMBLY – cam |
| 2 | G105118 | 1 | SEAL, oil |
| 3 | 37-1220 | 2 | DOWEL, 1/8″ x 1 1/4″, dowel, 1/8 x 1-1/4 inch, hardened |
| 4 | D65128 | 1 | BEARING, NEEDLE, shaft |
| 8 | 511-1020 | 3 | BALL, 2mm Dia, 2 mm, grade 28, chrome alloy steel |
| 9 | 511-1025 | 4 | BALL, 2.5mm Dia, 2.5 mm, grade 28, chrome alloy steel |
| 13 | 100-2137 | 4 | RING, SNAP, 0.375″, Int, #37, 0.375″, Int, #37 (Replaces 321298R1) |
| 14 | 1963882C1 | 1 | SPRING, VALVE, shuttle, detent |
| 15 | 1963881C1 | 1 | PLUG, hex, 1-1/16-12 inch, drive |
| 16 | 237-6012 | 1 | O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk |
| 17 | 93099C4 | 2 | COMPRESSION SPRING, DETENT – cam |
| 18 | 1286235C1 | 2 | SPRING, VALVE, detent, cam |
| 19 | 92957C1 | 2 | PLUG, detent |
| 20 | 237-8008 | 2 | O-RING, 8-1, Cl 8, .644″ ID x .087″ Thk |
| 23 | 1283927C2 | 1 | LEVER, speed, replaces 1283927C1 lever |
| 24 | 837-8020 | 1 | DOWEL, M8 x 20, dowel, 8 x 20 mm, hardened |
| 25 | 92498C1 | 1 | SHAFT, control cam, includes gear, replaces 1342284C1 gear and shaft kit |
| 30 | 93097C2 | 1 | CAM, ASSEMBLY – gear selector |
| 31 | A35822 | 2 | BEARING, cam |
| 32 | 1286263C2 | 1 | SPACER, bearing, cam |
| 33 | 92945C1 | 1 | SHAFT, cam |
| 38 | 92972C3 | 1 | SPRING, compression |
| 39 | 211-1012 | 1 | BALL, 3/8″ Dia, chrome alloy steel, 3/8 inch, grade 24 |
| 40 | 129998 | 2 | PLUG, Hex Hd, 1/2″-20 ORB |
| 41 | 237-6005 | 1 | O-RING, 5-1, 90 Duro, .414″ ID x .072″ Thk |
| 42 | 1286209C3 | 1 | PLATE ASSY., cover, valve |
| 43 | 1286265C5 | 1 | GASKET, plate, cover |
| 44 | 628-8025 | 12 | BOLT, Hex, M8 x 25, 10.9, Full Thd, See Fig. 6-38 |
| 45 | 1981142C1 | 1 | PLATE, LARGE, cover, valve |
| 46 | 92654C6 | 1 | GASKET, plate, cover |
| 47 | 86529630 | 2 | PLUG, Hex Soc, 3/8″-24 ORB |
| 48 | 237-6003 | 1 | O-RING, 3-1, .301″ ID x .064″ Thk |
| 50 | 828-8120 | 1 | BOLT, Hex, M8 x 120, 10.9, BOLT – hex, 8 – 1.25 x 120 mm, class 10.9, see fig.6-38 |
| 2 | 837-6035 | 2 | DOWEL, M6 x 35, dowel, 6 x 35 mm, hardened |
| 3 | 41-108 | 1 | PLUG, Cup, 1/2″, cup, 1/2 inch diameter |
| 4 | 92972C3 | 1 | SPRING, relief |
| 5 | 211-1012 | 1 | BALL, 3/8″ Dia, chrome alloy steel, 3/8 inch, grade 24, replaces 211-210 ball |
| 6 | 133519C1 | 2 | SCREEN, filter |
| 7 | 511-1060 | 2 | BALL, 6mm Dia, 6 mm, grade 28, chrome alloy steel |
| 9 | D65128 | 1 | BEARING, NEEDLE |
| 10 | 1286222C1 | 1 | STOP, spool, reducing |
| 11 | 1994615C2 | 1 | VALVE, CHECK |
| 12 | 1963809C1 | 1 | SPACER, spring |
| 13 | 37-1610 | 2 | PIN, 3/8″ x 5/8″, PIN – 3/8 x 5/8 inch, hardened, replaces 20031R1 pin |
| 21 | 1986857C1 | 1 | GASKET, housing to body |
| 22 | 1994584C2 | 1 | GASKET, body to plate |
| 23 | 109277A2 | 1 | PLATE, LARGE, ASSEMBLY – body, steel, if used |
| 23 | 117731A2 | 1 | PLATE, LARGE, ASSEMBLY – body, aluminum, if used |
| 24 | 1994615C2 | 2 | VALVE, CHECK |
| 30 | 1543349C2 | 1 | HOUSING ASSY., ASSEMBLY – control, clutch |
| 31 | 1963807C1 | 1 | SEAL, stem |
| 33 | 1286180C6 | 1 | GASKET, housing |
| 35 | 615-8030 | 3 | BOLT, Hex, M8 x 30, 8.8, Full Thd, BOLT – hex, full threads, 8 – 1.25 x 30 mm |
| 40 | 94806C3 | 1 | HOUSING ASSY., spool, forward/reverse, replaces 94806C4 housing |
| 41 | 1963843C1 | 1 | SEAL, spool |
| 43 | 93053C3 | 1 | GASKET, housing |
| 44 | 814-8075 | 1 | BOLT, Hex, M8 x 75, 8.8 |
| 45 | 94797C1 | 1 | PLATE, LARGE, housing |
| 46 | 813-8080 | 2 | BOLT, Hex, M8 x 80, 8.8, BOLT – hex, 8 – 1.25 x 80 mm |
| 47 | 1983218C2 | 1 | SWITCH, neutral start |
| 49 | 94799C1 | 1 | PLUG, housing |
| 50 | 238-5016 | 1 | O-RING, -016, 70 Duro, .614″ ID x .070″ Thk |
| 51 | 862-8055 | 3 | SCREW, Hex Soc Hd, M8 x 55, 12.9, BOLT – hex socket, 8 – 1.25 x 55 mm, class 12.9, see fig. 6-38 |
| 52 | 861-8070 | 4 | SCREW, Hex Soc Hd, M8 x 70, 12.9, BOLT – hex socket, 8 – 1.25 x 70 mm, class 12.9, see fig. 6-38 |
| 52 | 862-6070 | 1 | SCREW, Hex Soc Hd, M6 x 70, 12.9, BOLT – hex socket, 6 – 1.0 x 70 mm, class 12.9, see fig. 6-38 |
| 48 | 237-6006 | 1 | O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk |
| 2 | 93145C9 | 1 | PISTON, SPOOL – forward/reverse |
| 6 | 238-5021 | 1 | O-RING, -021, 70 Duro, .926″ ID x .070″ Thk |
| 7 | 1963812C3 | 1 | INSERT, SEAT – spring |
| 8 | 1963822C1 | 1 | SPRING, VALVE, detent |
| 9 | 1963818C1 | 1 | WASHER, stop |
| 11 | 94771C2 | 1 | PIN, LARGE, stop, reverse |
| 12 | 94775C1 | 1 | STOP, pin |
| 17 | 37-11224 | 1 | DOWEL, 3/4″ x 1 1/2″, dowel, 3/4 x 1-1/2 inch, hardened, replaces 23097R1 pin |
| 18 | 94798C4 | 1 | PLUNGER, valve |
| 19 | 1981069C2 | 1 | SPOOL, selector, 1-3-5 |
| 21 | 94783C1 | 1 | SPRING, VALVE, selector, lock pin |
| 22 | 94781C2 | 1 | PIN, LARGE, lock, selector, replaces 94781C1 pin |
| 23 | 1286251C3 | 1 | PIN, LARGE, spool, cam |
| 24 | K620272 | 1 | BEARING, NEEDLE, reaction |
| 25 | 1286264C1 | 1 | SPACER, bearing |
| 28 | 92971C1 | 1 | SPRING, VALVE, flow, sensor |
| 29 | 1286214C2 | 1 | SPOOL, overlap |
| 30 | 9672438 | 2 | PLUG, Hex Hd, 7/16″-20 ORB |
| 31 | 237-6004 | 1 | O-RING, 4-1, 90 Duro, .351″ ID x .072″ Thk |
| 41 | 117942A1 | 1 | ACCUMULATOR, RESERVOIR ASSEMBLY – 15 cubic inch, 116 mm (4-9/16 inch) diameter, includes |
| 42 | 1542910C1 | 1 | FITTING, CONNECTOR – 7/8-14 x 1-1/16-12 |
| 43 | 237-6010 | 1 | O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk |
| 44 | 237-6012 | 1 | O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk |
| 46 | 117941A1 | 1 | ACCUMULATOR, RESERVOIR ASSEMBLY – 30 cubic inch, 130 mm (5-1/8 inch) diameter, includes |
| 47 | 116371A1 | 1 | FITTING, CONNECTOR – 1-1/16-12 |
| 48 | 237-6012 | 2 | O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk |
| 2 | 1968260C2 | 1 | GASKET, lower plate and valve body |
| 3 | 1981070C1 | 1 | PLATE ASSY., lower, without creeper |
| 7 | 86529630 | 2 | PLUG, Hex Soc, 3/8″-24 ORB, Without creeper |
| 8 | 237-6003 | 1 | O-RING, 3-1, .301″ ID x .064″ Thk |
| 13 | 211-1007 | 1 | BALL, 7/32″ Dia, Gr 24, Chrome alloy steel, Replaces 211-205 ball |
| 15 | 38-11622 | 1 | PIN, LOCK, 1/4″ x 1 3/8″, Slotted, 1/4″ x 1 3/8″, Slotted |
| 16 | 86529630 | 7 | PLUG, Hex Soc, 3/8″-24 ORB |
| 17 | 237-6003 | 1 | O-RING, 3-1, .301″ ID x .064″ Thk |
| 18 | 1958159C2 | 1 | VALVE, SOLENOID, ASSEMBLY – drive, creeper |
| 19 | 238-5121 | 1 | O-RING, -121, 70 Duro, 1.049″ ID x .103″ Thk |
| 20 | 238-5017 | 1 | O-RING, -017, 70 Duro, .676″ ID x .070″ Thk |
| 21 | 238-5014 | 1 | O-RING, -014, 70 Duro, .489″ ID x .070″ Thk |
| 22 | 1968281C1 | 1 | RETAINER, solenoid valve |
| 23 | 940-148 | 2 | SCREW, Cross Pan Hd, M4 x 8, machine, pan Phillips, 4 – .7 x 8 mm, replaces 30841R1 screw |
| 26 | 1963881C1 | 1 | PLUG, hex, 1-1/16-12 inch, O-ring boss |
| 27 | 237-6012 | 1 | O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk, If used |
| 28 | 1968250C2 | 1 | COMPRESSION SPRING, replaces 1968250C1 spring |
| 29 | 1981127C3 | 1 | SPOOL, creeper valve |
| 30 | 1981071C1 | 1 | PLUG, valve body, with creeper, no longer included with 1981301C2 valve, purchase separately |
| 32 | 86529630 | 2 | PLUG, Hex Soc, 3/8″-24 ORB |
| 33 | 237-6003 | 1 | O-RING, 3-1, .301″ ID x .064″ Thk |
| 35 | 814-8050 | 3 | BOLT, Hex, M8 x 50, 8.8 |
| 36 | 813-8080 | 3 | BOLT, Hex, M8 x 80, 8.8, BOLT – hex, 8 – 1.25 x 80 mm, creeper only |
| 43 | 1963814C1 | 1 | SPRING, compression, creeper only |
| 44 | 1963815C1 | 1 | SPRING, compression, creeper only |
| 45 | 1981089C1 | 1 | STOP, spool, creeper only |
| 46 | 1981068C1 | 1 | SPOOL, blocker, creeper only |
| 47 | 837-6016 | 1 | DOWEL, M6 x 16, dowel, 6 x 16 mm, hardened, without creeper |
| 2 | 93135C4 | 1 | SPOOL, odd/even clutch, selector |
| 4 | 93139C5 | 1 | SPOOL, high/low, selector |
| 19 | 1286135C1 | 1 | SPOOL, reducing, includes screen, no longer available, order 295768A1 spool and 295767A1 ring |
| 19 | 295768A1 | 1 | SPOOL, reducing, requires 295767A1 retaining ring |
| 20 | 133519C1 | 1 | SCREEN, filter |
| 21 | 1286241C1 | 1 | SPRING, VALVE, reducting |
| 22 | 1286189C1 | 1 | WASHER, RING – spring retainer |
| 23 | 1286184C1 | 1 | SNAP RING, retainer, used with 1286135C1 spool |
| 23 | 295767A1 | 1 | SNAP RING, retaining, used with 295768A1 spool |
| 24 | 92525C3 | 1 | PISTON ASSY., spool |
| 25 | 92530C1 | 1 | SPRING, piston |
| 31 | 92534C2 | 1 | GUIDE, spring, modulating |
| 32 | 1286242C1 | 1 | SPRING, VALVE, inner, modulating |
| 33 | 1286243C1 | 1 | SPRING, VALVE, outer, modulating |
| 34 | 92936C3 | 1 | SPOOL, valve |
| 35 | 92976C1 | 1 | SPRING, VALVE, spool |
| 36 | 1286251C3 | 2 | PIN, LARGE, spool, cam |
| 37 | K620272 | 2 | BEARING, NEEDLE, reaction |
| 38 | 1286264C1 | 2 | SPACER, bearing |
| 39 | 94781C2 | 2 | PIN, LARGE, lock, selector |
| 40 | 94783C1 | 2 | SPRING, VALVE, lock pin |
| 1 | 613-8025 | 12 | BOLT, Hex, M8 x 25, 8.8, Full Thd, BOLT – hex, full threads, 8 – 1.25 x 25 mm |
| 5 | 828-8120 | 1 | BOLT, Hex, M8 x 120, 10.9, BOLT – hex, 8 – 1.25 x 120 mm, class 10.9 |
| 6 | 862-8055 | 3 | SCREW, Hex Soc Hd, M8 x 55, 12.9, BOLT – hex socket, 8 – 1.25 x 55 mm, class 12.9 |
| 8 | 861-8070 | 4 | SCREW, Hex Soc Hd, M8 x 70, 12.9, BOLT – hex socket, 8 – 1.25 x 70 mm, class 12.9 |
| 9 | 862-6070 | 1 | SCREW, Hex Soc Hd, M6 x 70, 12.9, BOLT – hex socket, 6 – 1.0 x 70 mm, class 12.9 |
| 10 | 828-8120 | 3 | BOLT, Hex, M8 x 120, 10.9, BOLT – hex, 8 – 1.25 x 120 mm, class 10.9 |
| 11 | 828-8140 | 8 | BOLT, Hex, M8 x 140, 10.9, BOLT – hex, 8 – 1.25 x 140 mm, class 10.9, replaces 31256R1 bolt |
| 12 | 814-10175 | 2 | SCREW, BOLT – hex, 10 – 1.5 x 175 mm |
| 13 | 813-10065 | 3 | BOLT, Hex, M10 x 65, 8.8, BOLT – hex, 10 – 1.5 x 65 mm |
| 14 | 814-10055 | 4 | BOLT, Hex, M10 x 55, 8.8 |
| 1 | 1997446C2 | 1 | SHAFT ASSY., input |
| 2 | 1342852C1 | 4 | PLUG, sealing, 12 mm |
| 3 | 38-3605 | 5 | PIN, 3/32″ x 5/16″, Coiled |
| 4 | 1963874C1 | 1 | PIN, coiled, 8 x 14 mm |
| 8 | 1286040C2 | 1 | RING, support, bearing |
| 9 | 1997888C1 | 1 | WASHER, THRUST |
| 10 | 80909C1 | 2 | BEARING, NEEDLE, needle, caged |
| 11 | 1285977C1 | 1 | GEAR, GEAR – driver, 37 teeth, medium |
| 12 | 1285979C1 | 1 | PINION, GEAR – drive, 52 teeth, high range |