7220 CASE IH Magnum Tractor (North America)
7220 CASE IH Magnum Tractor (North America) — parts list, part 4 of 5
Assemblies on this page: Parts list (continued) … Parts list (continued).
Parts list (continued)
| Pos | Part no. | Qty | Description |
|---|---|---|---|
| 19 | 1543329C1 | 1 | POPPET, VALVE, PLUG |
| 20 | G108723 | 1 | RING, backup |
| 21 | 238-6015 | 1 | O-RING, -015, 90 Duro, .551″ ID x .070″ Thk |
| 22 | 1994581C1 | 1 | SPRING, load check |
| 29 | 1346312C2 | 1 | PLUG, sleeve |
| 30 | 238-6012 | 1 | O-RING, -012, 90 Duro, .364″ ID x .070″ Thk |
| 31 | L31750 | 1 | CIRCLIP, 0.562″, Int, #56, 0.562″, Int, #56 |
| 32 | 1980302C2 | 1 | ROD, ASSEMBLY – adjusting, flow |
| 33 | 138-56 | 1 | PIN, LOCK, 1/8″ x 11/16″, Slotted |
| 34 | G101066 | 1 | SEAL, oil |
| 35 | 1980226C1 | 1 | PLUG, adjusting |
| 36 | 1980227C1 | 1 | PLUG, NUT – compression |
| 37 | G108956 | 1 | RACE, bearing, thin |
| 38 | G108957 | 1 | RACE, bearing, thick |
| 39 | 237-6010 | 1 | O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk |
| 40 | 1986628C1 | 5 | O-RING, 3/8 ID x 9/16 inch wide |
| 41 | F13537 | 1 | BEARING, thrust |
| 50 | 1976957C1 | 1 | COVER ASSY, detent |
| 51 | G108911 | 1 | WASHER, detent, ball outer |
| 52 | G108912 | 1 | WASHER, detent, ball inner |
| 53 | 211-1007 | 8 | BALL, 7/32″ Dia, Gr 24, Chrome alloy steel |
| 54 | 1341975C1 | 1 | CUP, SPRING, RETAINER – detent |
| 55 | G107780 | 1 | VALVE, CHECK, PLUG – retainer |
| 56 | G110152 | 1 | SPRING, detent |
| 57 | G108908 | 1 | PISTON, detent |
| 58 | G108728 | 1 | BACK-UP RING, large |
| 59 | G108922 | 1 | BACK-UP RING, small |
| 60 | 238-6020 | 1 | O-RING, -020, 90 Duro, .864″ ID x .070″ Thk |
| 61 | 238-6021 | 1 | O-RING, -021, 90 Duro, .926″ ID x .070″ Thk |
| 62 | G110300 | 1 | PLUG, adjusting, pilot relief |
| 63 | G110279 | 1 | POPPET, VALVE, relief |
| 64 | G110289 | 1 | BACK-UP RING |
| 69 | G110281 | 2 | CUP, SPRING, WASHER – retainer |
| 70 | G108918 | 1 | ORIFICE, WASHER |
| 71 | G109275 | 1 | SPRING, pilot |
| 72 | 238-6011 | 1 | O-RING, -011, 90 Duro, .301″ ID x .070″ Thk |
| 73 | 238-6015 | 1 | O-RING, -015, 90 Duro, .551″ ID x .070″ Thk |
| 75 | 238-6012 | 1 | O-RING, -012, 90 Duro, .364″ ID x .070″ Thk |
| 76 | 425-1510 | 1 | NUT, Jam, 5/8″-18, G5, Hex |
| 77 | 238-5004 | 1 | O-RING, -004, 70 Duro, .07″ ID x .070″ Thk |
| 78 | 100-21118 | 1 | RING, SNAP, 1.188″, Int, #118, (Replaces A30975) |
| 79 | 61-31016 | 3 | SCREW, Hex Soc Hd, #10-24 x 1″ |
| 80 | 495-11022 | 3 | WASHER, #10, (Flat, 7/32″ x 7/16″ x 3/64″) |
| 86 | 1957817C1 | 1 | SPRING, VALVE, poppet |
| 87 | 1957964C1 | 1 | RETAINER, spring |
| 88 | 1957965C1 | 1 | SPRING, VALVE, main |
| 91 | G110295 | 1 | O-RING, -013, 90 Duro, .426″ ID x .070″ Thk, poppet |
| 92 | G110287 | 1 | BACK-UP RING, inner |
| 93 | G108727 | 1 | BACK-UP RING, outer |
| 94 | 238-6014 | 1 | O-RING, -014, 90 Duro, .489″ ID x .070″ Thk |
| 95 | 237-6008 | 2 | O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk |
| 96 | G108724 | 1 | BACK-UP RING |
| 97 | 1971475C1 | 1 | PLUG, lock check |
| 98 | 237-6008 | 1 | O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk |
| 99 | G110295 | 1 | O-RING, -013, 90 Duro, .426″ ID x .070″ Thk, poppet |
| 100 | G110287 | 1 | BACK-UP RING, inner |
| 2 | 185448A2 | 1 | SPRING, control, flow, replaces 185447A1 |
| 3 | 1957861C1 | 1 | WASHER, retainer |
| 4 | 1957862C1 | 1 | PISTON, load check |
| 5 | 1957859C1 | 1 | RING, SNAP |
| 6 | 71121 | 1 | SEAL, WIPER – piston |
| 7 | G110391 | 1 | O-RING, piston |
| 8 | 86529630 | 1 | PLUG, Hex Soc, 3/8″-24 ORB |
| 9 | 237-6003 | 1 | O-RING, 3-1, .301″ ID x .064″ Thk |
| 10 | 1542571C1 | 1 | SPOOL, main |
| 11 | 246405A1 | 1 | STUD, detent, replaces 1543364C1 stud |
| 12 | G108913 | 1 | CUP, SPRING, SEAT – outer |
| 13 | G108914 | 1 | CUP, SPRING, SEAT – inner |
| 14 | G108915 | 1 | SPRING, centering |
| 15 | G108630 | 1 | HOLDER, RETAINER – O-ring |
| 16 | G110391 | 1 | O-RING, spool |
| 17 | 237-6002 | 1 | O-RING, 2-1, .239″ ID x .064″ Thk |
| 19 | 1543329C1 | 1 | POPPET, VALVE, PLUG |
| 20 | G108723 | 1 | RING, backup |
| 21 | 238-6015 | 1 | O-RING, -015, 90 Duro, .551″ ID x .070″ Thk |
| 22 | 1994581C1 | 1 | SPRING, load check |
| 29 | 183491A1 | 1 | PLUG, sleeve |
| 30 | 238-6013 | 1 | O-RING, -012, 90 Duro, .364″ ID x .070″ Thk, 7/16 ID x 1/16 inch wide |
| 32 | 1980302C2 | 1 | ROD, ASSEMBLY – adjusting, flow |
| 33 | 138-56 | 1 | PIN, LOCK, 1/8″ x 11/16″, Slotted |
| 34 | G101066 | 1 | SEAL, oil |
| 35 | 1980226C1 | 1 | PLUG, adjusting |
| 36 | 1980227C1 | 1 | PLUG, NUT – compression |
| 37 | G108956 | 1 | RACE, bearing, thin |
| 38 | G108957 | 1 | RACE, bearing, thick |
| 39 | 237-6010 | 1 | O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk |
| 40 | 1986628C1 | 5 | O-RING, 3/8 ID x 9/16 inch wide |
| 41 | F13537 | 1 | BEARING, thrust |
| 50 | 186439A1 | 1 | COVER ASSY, detent |
| 51 | G108911 | 1 | WASHER, detent, ball outer |
| 52 | G108912 | 1 | WASHER, detent, ball inner |
| 53 | 211-1007 | 8 | BALL, 7/32″ Dia, Gr 24, Chrome alloy steel |
| 54 | 321361A1 | 1 | RETAINER, ASSEMBLY – detent, replaces 1341975C1 retainer |
| 55 | G107780 | 1 | VALVE, CHECK, PLUG – retainer |
| 56 | G110152 | 1 | SPRING, detent |
| 57 | G108908 | 1 | PISTON, detent |
| 58 | G108728 | 1 | BACK-UP RING, large |
| 59 | G108922 | 1 | BACK-UP RING, small |
| 60 | 238-6020 | 1 | O-RING, -020, 90 Duro, .864″ ID x .070″ Thk |
| 61 | 238-6021 | 1 | O-RING, -021, 90 Duro, .926″ ID x .070″ Thk |
| 62 | G110300 | 1 | PLUG, adjusting, pilot relief |
| 63 | G110279 | 1 | POPPET, VALVE, relief |
| 64 | G110289 | 1 | BACK-UP RING |
| 69 | G110281 | 2 | CUP, SPRING, WASHER – retainer |
| 70 | G108918 | 1 | ORIFICE, WASHER |
| 71 | G109275 | 1 | SPRING, pilot |
| 72 | 238-6011 | 1 | O-RING, -011, 90 Duro, .301″ ID x .070″ Thk |
| 73 | 238-6015 | 1 | O-RING, -015, 90 Duro, .551″ ID x .070″ Thk |
| 75 | 238-6012 | 1 | O-RING, -012, 90 Duro, .364″ ID x .070″ Thk |
| 76 | 425-1510 | 1 | NUT, Jam, 5/8″-18, G5, Hex |
| 77 | 238-5004 | 1 | O-RING, -004, 70 Duro, .07″ ID x .070″ Thk |
| 78 | 100-21118 | 1 | RING, SNAP, 1.188″, Int, #118 |
| 79 | 61-31016 | 3 | SCREW, Hex Soc Hd, #10-24 x 1″ |
| 80 | 495-11022 | 3 | WASHER, #10, (Flat, 7/32″ x 7/16″ x 3/64″) |
| 86 | 1957817C1 | 1 | SPRING, VALVE, poppet |
| 87 | 1957964C1 | 1 | RETAINER, spring |
| 88 | 1957965C1 | 1 | SPRING, VALVE, main |
| 91 | G110295 | 1 | O-RING, -013, 90 Duro, .426″ ID x .070″ Thk, poppet |
| 92 | G110287 | 1 | BACK-UP RING, inner |
| 93 | G108727 | 1 | BACK-UP RING, outer |
| 94 | 238-6014 | 1 | O-RING, -014, 90 Duro, .489″ ID x .070″ Thk |
| 95 | 237-6008 | 2 | O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk |
| 96 | G108724 | 1 | BACK-UP RING |
| 97 | 1971475C1 | 1 | PLUG, lock check |
| 98 | 237-6008 | 1 | O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk |
| 99 | 238-6013 | 1 | O-RING, -012, 90 Duro, .364″ ID x .070″ Thk, 7/16 ID x 1/16 inch wide, poppet, replaces G110295 |
| 100 | G110287 | 1 | BACK-UP RING, inner |
| 2 | 93329C2 | 1 | SPRING, retainer |
| 3 | 93328C3 | 2 | CARTRIDGE, coupler |
| 4 | 93330C1 | 2 | SPRING, VALVE, tension |
| 5 | 100-28162 | 2 | RING, SNAP, 1.625″, Int, #162, (Replaces 206321H1) |
| 6 | 238-5027 | 4 | O-RING, -027, 70 Duro, 1.301″ ID x .070″ Thk |
| 7 | 93332C1 | 4 | SEAL ASSY., oil, slipper |
| 8 | A47221 | 2 | SEAL, RING |
| 2 | 201-103 | 2 | CONNECTOR, HYD., 1″-14 ORFS x 7/8″-14 ORB |
| 3 | 237-6010 | 1 | O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk, Boss end |
| 4 | 238-6016 | 1 | O-RING, -016, 90 Duro, .614″ ID x .070″ Thk, Face end |
| 5 | 238-6117 | 6 | O-RING, -117, 90 Duro, .799″ ID x .103″ Thk |
| 6 | 238-6112 | 2 | O-RING, -112, 90 Duro, .487″ ID x .103″ Thk |
| 7 | 1994613C1 | 2 | STUD, 12 x 268 mm |
| 8 | 1334559C2 | 1 | STUD, 10 x 275 mm |
| 9 | 829-1312 | 2 | NUT, M12 x 1.75, Cl 10 |
| 10 | 829-1310 | 1 | NUT, M10, Cl 10, Class 10.9 |
| 11 | 102219A1 | 1 | PIPE, TUBE – raise, third circuit |
| 12 | 102220A1 | 1 | PIPE, TUBE – drop, third circuit |
| 13 | 1289355C1 | 1 | SUPPORT ASSY., tube |
| 14 | 486004R1 | 1 | CLAMP, tube |
| 15 | 224968C2 | 1 | STRIP, CLAMP – isomount strip |
| 16 | 828-8040 | 1 | BOLT, Hex, M8 x 40, 10.9, BOLT – hex, 8 – 1.25 x 40 mm, class 10.9 |
| 17 | 832-41308 | 1 | NUT, M8 x 1.25, Cl 10, hex, self-locking, 8 mm – 1.25, class 10.9 |
| 18 | 102519A1 | 1 | SUPPORT, BRACKET – coupler, right-hand |
| 19 | 628-16030 | 2 | BOLT, Hex, M16 x 30, 10.9, Full Thd, Bolt, Hex, M16 x 30, 10.9, Full Thd |
| 20 | 103866A2 | 1 | COUPLING, ASSEMBLY – quick disconnect, parts list fig. 8-74 |
| 21 | 201-306 | 2 | ELBOW, 90є, 1″-14 x 7/8″-14 Adj, ORFS, 90 degree, 1-14 face seal x 7/8-14 inch adj O-ring boss |
| 22 | 237-6010 | 1 | O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk, Boss end |
| 23 | 238-6016 | 1 | O-RING, -016, 90 Duro, .614″ ID x .070″ Thk, Face end |
| 24 | 628-12020 | 2 | BOLT, Hex, M12 x 20, 10.9, Full Thd, BOLT – hex, full threads, 12 – 1.75 x 20 mm, class 10.9 |
| 25 | 217-430 | 1 | PLUG, Hex Soc, 1/8″-27 |
| 26 | 221-1101 | 1 | FITTING, NIPPLE – straight, 1/8 PT x 3/4 inch |
| 27 | 1348264C1 | 1 | CLAMP, HOSE, 3/8 inch |
| 28 | 106514A1 | 1 | HOSE, LARGE, 808 mm (30-13/16 inch) long, coupler drain |
| 29 | L18337 | 1 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch |
| 30 | 1289481C1 | 1 | ELBOW, 90 degree |
| 31 | 1334641C1 | 1 | HOSE ASSY., 330 mm (13 inch) long, cut from 427683C1 bulk hose, coupler, elbow to tee |
| 32 | 1289479C1 | 1 | TEE, barbed, used on models with hitch |
| 33 | 1289484C1 | 1 | HOSE ASSY., 115 mm (4-9/16 inch) long, cut from 427683C1 bulk hose, drain, tee to tee |
| 34 | 1334583C3 | 1 | DECAL, 3 ISO, third coupler, shown on fig. 9-146 |
| 35 | 1334586C1 | 1 | PLUG, ADAPTER – coupler drain, special |
| 36 | 238-6116 | 1 | O-RING, -116, 90 Duro, .737″ ID x .103″ Thk |
| 37 | 103871A1 | 2 | CAP, PLUG – dust, coupler |
| 40 | 104301A1 | 1 | COVER, DOOR, coupler |
| 41 | 104302A1 | 1 | PLATE, retaining |
| 42 | 104303A1 | 1 | SCREW, BOLT – shoulder |
| 43 | 461-4258 | 1 | SCREW, Hex Soc Flat Hd, 1/4″-20 x 1/2″, BOLT – hex socket, 1/4 NC x 1/2 inch |
| 44 | 110947A1 | 1 | WASHER, flat, special, special |
| 45 | 110945A1 | 1 | SPRING, coupler door |
| 2 | 111793A1 | 1 | BUSHING, LARGE, BEARING – control lever |
| 3 | 111795A1 | 1 | NUT, bearing |
| 5 | 111793A1 | 1 | BUSHING, LARGE, BEARING – control lever |
| 6 | 111795A1 | 1 | NUT, bearing |
| 8 | 111793A1 | 1 | BUSHING, LARGE, BEARING – control lever |
| 9 | 111795A1 | 1 | NUT, bearing |
| 11 | 111793A1 | 1 | BUSHING, LARGE, BEARING – control lever |
| 12 | 111795A1 | 1 | NUT, bearing |
| 14 | 111934A2 | 1 | SHAFT, pivot, handle |
| 16 | 1999689C1 | 1 | SUPPORT, pivot |
| 17 | 1999940C1 | 1 | HOLDER, SUPPORT – cable, flow control |
| 18 | 1999944C3 | 1 | PLATE ASSY., selector valve, replaces 1999944C2 plate |
| 19 | 825-1408 | 10 | NUT, M8, Cl 8 |
| 20 | 1283979C1 | 1 | BRACKET, mounting, rear |
| 21 | 495-11034 | 8 | WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch, replaces 495-11034 washer |
| 22 | 614-8016 | 2 | BOLT, Hex, M8 x 16, 8.8 |
| 23 | 832-10408 | 1 | NUT, LOCK, M8 x 1.25, Cl 8 |
| 27 | 814-8140 | 1 | BOLT, Hex, M8 x 140, 8.8 |
| 28 | 96829C1 | 1 | PIN, AXLE, lock, neutral |
| 29 | 614-6012 | 2 | BOLT, Hex, M6 x 12, 8.8 |
| 30 | 896-11006 | 2 | WASHER, M6 x 13 x 2, HT |
| 33 | 96851C2 | 1 | LEVER, neutral, lockout |
| 34 | 565-107 | 1 | SCREW, Hex Soc Hd, M4 x 20, 8.8, BOLT – hex socket, 4 – .7 x 20 mm |
| 35 | 1251730C2 | 1 | WASHER, friction, lockout lever |
| 36 | 96963C2 | 1 | SPACER, lever |
| 37 | 832-10404 | 1 | NUT, LOCK, M4 x .7, Cl 8, hex, self-locking, 4 mm – 0.7 |
| 38 | 895-11004 | 1 | WASHER, M4, flat, 4.4 x 9 x 0.8 mm |
| 39 | 127123A1 | 2 | LEVER, float lockout, first and second remote |
| 51 | 1283978C1 | 1 | BRACKET, mounting, front |
| 52 | 1283976C4 | 1 | SUPPORT, PLATE – support, valve |
| 53 | 614-8020 | 3 | BOLT, Hex, M8 x 20, 8.8 |
| 54 | 1999943C1 | 1 | DECAL, auxiliary valve control lever pattern, not shown, see fig. 9-148 for decals |
| 55 | 122662A2 | 2 | CABLE, flow control, No. 1 and No. 2 |
| 56 | 122663A2 | 1 | CABLE, flow control, No. 3 |
| 57 | 122664A2 | 1 | CABLE, flow control, No. 4 |
| 58 | A160814 | 2 | KNOB, flow control, tractors without in-cab flow control |
| 59 | 96987C1 | 2 | GROMMET, tractors without in-cab flow control |
| 60 | 484-21010 | 2 | SET SCREW, Hex Soc, #10-32 x 5/8″, set, hex socket, No.10 NF x 5/8 inch, tractors without in-cab |
| 2 | 238-6117 | 6 | O-RING, -117, 90 Duro, .799″ ID x .103″ Thk |
| 3 | 238-6112 | 2 | O-RING, -112, 90 Duro, .487″ ID x .103″ Thk |
| 4 | 1986938C1 | 2 | STUD, 12 x 312 mm |
| 5 | 1334613C2 | 1 | STUD, 10 – 1.5 x 312 mm |
| 6 | 201-103 | 2 | CONNECTOR, HYD., 1″-14 ORFS x 7/8″-14 ORB |
| 7 | 237-6010 | 1 | O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk, Boss end |
| 8 | 238-6016 | 1 | O-RING, -016, 90 Duro, .614″ ID x .070″ Thk, Face end |
| 9 | 201-306 | 2 | ELBOW, 90є, 1″-14 x 7/8″-14 Adj, ORFS, 90 degree, 1-14 face seal x 7/8-14 inch adj O-ring boss |
| 10 | 237-6010 | 1 | O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk, Boss end |
| 11 | 238-6016 | 1 | O-RING, -016, 90 Duro, .614″ ID x .070″ Thk, Face end |
| 12 | 102221A1 | 1 | PIPE, TUBE – raise, fourth valve |
| 13 | 102222A1 | 1 | PIPE, TUBE – drop, fourth valve |
| 14 | 1334203C1 | 1 | SUPPORT ASSY., tube |
| 15 | 815-8070 | 1 | BOLT, Hex, M8 x 70, 8.8, BOLT – hex, 8 – 1.25 x 70 mm |
| 16 | 486004R1 | 2 | CLAMP, tube |
| 17 | 224968C2 | 2 | STRIP, CLAMP – isomount |
| 18 | 832-41308 | 1 | NUT, M8 x 1.25, Cl 10, hex, self-locking, 8 mm – 1.25, class 10.9 |
| 19 | 120012C1 | 1 | SUPPORT, coupler |
| 20 | 614-12025 | 2 | BOLT, Hex, M12 x 25, 8.8, At third circuit coupler |
| 21 | 103866A2 | 1 | COUPLING, ASSEMBLY – quick disconnect, parts list fig. 8-74 |
| 22 | 221-1101 | 1 | FITTING, NIPPLE – straight, 1/8 PT x 3/4 inch |
| 23 | 1272764C1 | 1 | SEAL ASSY., drain |
| 24 | 1334586C1 | 1 | PLUG, ADAPTER – coupler drain, special |
| 24 | 238-6116 | 1 | O-RING, -116, 90 Duro, .737″ ID x .103″ Thk |
| 25 | 1289480C1 | 1 | TEE, barbed, at third circuit coupler |
| 26 | 1289484C1 | 1 | HOSE ASSY., 115 mm (4-9/1 6 inch) long, cut from 427683C1 bulk hose, drain, elbow to tee |
| 27 | 1334584C3 | 1 | DECAL, 4 ISO, fourth coupler, shown on fig. 9-146 |
| 28 | 103871A1 | 2 | CAP, PLUG – dust, coupler |
| 31 | 1289481C1 | 1 | ELBOW, 90 degree, special, Located at third circuit coupler, move to fourth circuit coupler when |
| 32 | 628-12020 | 2 | BOLT, Hex, M12 x 20, 10.9, Full Thd, BOLT – hex, full threads, 12 – 1.75 x 20 mm, class 10.9, Located |
| 33 | 217-430 | 1 | PLUG, Hex Soc, 1/8″-27, , Located at third circuit coupler, move to fourth circuit coupler when adding |
| 38 | 110947A1 | 1 | WASHER, flat, special |
| 1 | 1272400C1 | 1 | COUPLING, self sealing, female |
| 2 | 1954133C1 | 1 | DUST CAP, coupling, dust |
| 3 | 1348201C1 | 1 | SUPPORT, BRACKET – return line |
| 4 | A66788 | 1 | CLAMP, U-BOLT – 1-13/32 x 2 x 1/4 inch NC |
| 5 | 425-104 | 4 | NUT, 1/4″-20, G5 |
| 6 | 492-11025 | 2 | WASHER, LOCK, 1/4″ |
| 9 | 201-107 | 1 | CONNECTOR, HYD., 1 3/16″-12 ORFS x 7/8″-14 ORB, ADAPTER – straight, 1-3/16-12 face seal x |
| 10 | 238-6018 | 1 | O-RING, -018, 90 Duro, .739″ ID x .070″ Thk |
| 11 | 237-6010 | 1 | O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk |
| 12 | 1348302C1 | 1 | HOSE, 2075 mm (81-11/16 inch) long, oil return |
| 13 | 201-428 | 1 | TEE, 1 3/16″-12 x 1 1/16″-12 Run, ORFS, 1-3/16-12 face seal branch x face seal x 1-1/16-12 inch adj |
| 14 | 238-6018 | 2 | O-RING, -018, 90 Duro, .739″ ID x .070″ Thk |
| 15 | 237-6012 | 1 | O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk |
| 18 | 515-23302 | 1 | CLAMP, 1 3/16″, Insul, 3/8″ Bolt, P-type, 1-3/16 inch ID, replaces 28122R1 clamp |
| 19 | 614-8020 | 1 | BOLT, Hex, M8 x 20, 8.8 |
| 20 | 825-1408 | 1 | NUT, M8, Cl 8 |
| 22 | 1342123C2 | 1 | HOSE, return, 967 mm (38-1/8 inch) long, steering |
| 2 | 1331849C1 | 1 | BUSHING, rockshaft, left |
| 3 | 1331848C1 | 1 | BUSHING, rockshaft, right |
| 4 | 76349 | 2 | PLUG, Hex Hd, 9/16″-18 ORB, without hitch |
| 6 | 86512512 | 1 | PLUG, Hex Hd, 7/8″-14 ORB, Without hitch |
| 7 | 237-6010 | 1 | O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk |
| 8 | 380174R1 | 1 | PLUG, Cup, 3.510″, cup, 3-33/64 inch OD, without hitch |
| 9 | 380173R1 | 1 | PLUG, Cup, 3.762″, cup, 3-49/64 inch OD |
| 10 | 380263R1 | 4 | PLUG, cup, without hitch |
| 11 | 1342165C1 | 1 | LEVER, link, potentiometer |
| 12 | 413-416 | 1 | BOLT, Hex, 1/4″-20 x 1″, G5 |
| 13 | 492-11025 | 1 | WASHER, LOCK, 1/4″ |
| 16 | 614-16100 | 16 | BOLT, Hex, M16 x 100, 8.8, Full Thd, BOLT – hex, full threads, 16 – 2.0 x 100 mm |
| 17 | 1347918C1 | 1 | SEAL, oil, rockshaft, left |
| 18 | 1347919C1 | 1 | SEAL, oil, rockshaft, right |
| 19 | 380264R3 | 1 | GASKET, rear frame cover |
| 20 | 1973956C1 | 1 | ROCKSHAFT, hitch control |
| 21 | 84923C2 | 1 | DIPPER, BELLCRANK – rockshaft |
| 22 | 382811R1 | 1 | SCREW, special, rockshaft bellcrank |
| 23 | 84922C1 | 1 | ROD, piston connecting |
| 24 | 38-12840 | 1 | PIN, LOCK, 7/16″ x 2 1/2″, Slotted, 7/16″ x 2 1/2″, Slotted |
| 26 | 1340665C1 | 1 | SUPPORT, BRACKET – potentiometer |
| 27 | 614-10035 | 1 | BOLT, Hex, M10 x 35, 8.8, Full Thd |
| 28 | 895-11010 | 1 | WASHER, M10 x 20 x 2 |
| 29 | 832-10410 | 1 | NUT, LOCK, M10 x 1.5, Cl 8 |
| 36 | 492-21062 | 1 | WASHER, LOCK, 5/8″, 5/8″ |
| 37 | 38-11616 | 1 | PIN, LOCK, 1/4″ x 1″, Slotted |
| 38 | 1340669C1 | 1 | LEVER, sensor, rockshaft |
| 39 | 413-1024 | 1 | BOLT, Hex, 5/8″-11 x 1 1/2″, G5, Full Thd, Rockshaft arm (Right) |
| 39 | 413-1020 | 1 | BOLT, Hex, 5/8″-11 x 1 1/4″, G5, Full Thd, Rockshaft arm (Left) |
| 40 | 1286931C3 | 1 | LINK, LOWER, ARM ASSEMBLY – rockshaft, left, includes item 41, if used |
| 40 | 1286930C5 | 1 | LINK, LOWER, ARM ASSEMBLY – rockshaft, right, shown |
| 41 | 1252114C1 | 2 | BUSHING, pivot |
| 42 | 145474C1 | 2 | PIN, LARGE, cylinder mounting |
| 43 | 838-3655 | 2 | PIN, roll, 6 x 55 mm, replaces 30570R1 pin |
| 44 | 388574R1 | 2 | WASHER, rockshaft arm retaining |
| 45 | 1342171C2 | 1 | ROD ASSY., link, potentiometer, replaces 1342171C1 rod |
| 46 | 814-6055 | 4 | BOLT, Hex, M6 x 55, 8.8, BOLT – hex, 6 – 1.0 x 55 mm |
| 47 | 825-5146 | 4 | NUT, M6, Flg Ser |
| 50 | 1340666C1 | 1 | HOUSING, potentiometer |
| 51 | 1348212C1 | 1 | SHAFT, potentiometer sensor |
| 52 | 493-81008 | 2 | WASHER, LOCK, Int Tooth, 5/16″, internal tooth, 5/16 inch |
| 53 | 495-11034 | 2 | WASHER, 5/16″, SAE, WASHER – flat, 11/32 x 11/16 x 1/16 inch |
| 54 | 425-115 | 1 | NUT, 5/16″-24, G5 |
| 55 | L18337 | 1 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch |
| 56 | 413-616 | 1 | BOLT, Hex, 3/8″-16 x 1″, G5, Full Thd, hex, 3/8 NC x 1 inch |
| 57 | 492-11038 | 1 | WASHER, LOCK, 3/8″ |
| 60 | 1286923C2 | 1 | ARM, ASSEMBLY – rockshaft, left, includes item 41, if used |
| 5 | 237-6006 | 1 | O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk |
| 1 | 1266971C4 | 1 | BRACKET, HITCH, link mounting (7220) shown |
| 1 | 142614C3 | 1 | BRACKET, link mounting (7210) |
| 2 | 1286840C7 | 1 | PIN, HITCH, upper link bracket, replaces 1286840C5 pin |
| 3 | 1978738C1 | 1 | PIN, SPLIT (COTTER), cotter, hair, 3/16 inch |
| 4 | 828-20080 | 6 | BOLT, Hex, M20 x 80, 10.9, (With hitch) |
| 4 | 613-20050 | 6 | BOLT, Hex, M20 x 50, 8.8, Full Thd, BOLT – 20 x 50 mm (Without hitch) |
| 5 | 1954221C2 | 1 | LINK, TURNBUCKLE – upper link, replaces 1954221C1 turnbuckle |
| 6 | 1331863C2 | 1 | HANDLE, turnbuckle |
| 7 | 1981986C1 | 1 | END, ROD – upper link, right-hand thread, without keyway |
| 8 | 219-87 | 2 | NIPPLE, LUBE, 1/4″-28 x .56″ lg, Self-Tap |
| 9 | 1978738C1 | 1 | PIN, SPLIT (COTTER), cotter, hair, 3/16 inch |
| 10 | 427-6200 | 1 | PIN, CLEVIS, 3/8″ x 2″, 3/8 x 2 inch, hardened |
| 11 | 432-612 | 1 | PIN, SPLIT (COTTER), 3/32″ x 3/4″ |
| 12 | 1282063C2 | 1 | END, ROD – upper link, left-hand thread |
| 13 | 838-3638 | 2 | PIN, M6 x 38, Coiled, roll, 6 x 38 mm, replaces 31042R1 pin |
| 14 | 1954223C2 | 1 | ARM, TURNBUCKLE – 1-3/4″ thread, upper link, replaces 1954223C1 turnbuckle |
| 15 | 1331863C2 | 1 | HANDLE, turnbuckle |
| 16 | 1981988C1 | 1 | END ASSY., SCREW ASSEMBLY – 1-3/4″ thread, includes ball, right-hand thread, without keyway |
| 17 | 219-87 | 2 | NIPPLE, LUBE, 1/4″-28 x .56″ lg, Self-Tap |
| 18 | 1978738C1 | 1 | PIN, SPLIT (COTTER), cotter, hair, 3/16 inch |
| 19 | 427-6200 | 1 | PIN, CLEVIS, 3/8″ x 2″, 3/8 x 2 inch, hardened |
| 20 | 432-612 | 1 | PIN, SPLIT (COTTER), 3/32″ x 3/4″ |
| 21 | 1282082C2 | 1 | END, SCREW ASSEMBLY – includes ball, left-hand thread |
| 22 | 838-5645 | 2 | PIN, LOCK, M6 x 45, Slotted, roll, 6 x 45 mm |
| 23 | 149836C4 | 1 | TURNBUCKLE, lift link |
| 24 | 219-86 | 3 | NIPPLE, LUBE, 1/8″ x .62″ lg, Drive, grease, straight, self-tap 1/8 PT x 5/8 inch |
| 25 | 149837C1 | 1 | ROD, leveling, without grease fitting port and without bushings, if used |
| 26 | 1272674C1 | 2 | BUSHING, pivot |
| 27 | 219-87 | 1 | NIPPLE, LUBE, 1/4″-28 x .56″ lg, Self-Tap |
| 28 | 1266968C1 | 1 | YOKE, lift link |
| 29 | 413-652 | 1 | BOLT, Hex, 3/8″-16 x 3 1/4″, G5 |
| 30 | 495-11041 | 2 | WASHER, 3/8″, SAE, Flat, (13/32 x 13/16 x 1/16″) |
| 31 | 231-4116 | 1 | NUT, LOCK, 3/8″-16, GB, hex, self-locking, 3/8 inch NC |
| 32 | 123464C3 | 1 | CLAMP, turnbuckle lock, replaces 123464C2 clamp |
| 33 | 39-51260 | 1 | PIN, HEADED, 3/4″ x 3 3/4″, headed, 3/4 x 3-3/4 inch, replaces 27357R1 pin |
| 34 | 480523R1 | 1 | SPLIT PIN/SAFETY PIN, hair |
| 35 | 149838C1 | 1 | ROD, leveling |
| 36 | 1286725C2 | 1 | BRACKET, PIVOT, SWIVEL ASSEMBLY – lift link, includes two bushings, item 38 and one grease |
| 37 | 1272670C2 | 1 | PIVOT, SWIVEL ASSEMBLY – lift link |
| 40 | 1266969C1 | 1 | PIN, AXLE, head |
| 41 | 432-1620 | 2 | PIN, SPLIT (COTTER), 1/4″ x 1 1/4″, 1/4″ x 1 1/4″ |
| 42 | 39-51276 | 2 | PIN, HEADED, 3/4″ x 4 3/4″, clevis |
| 43 | 838-5636 | 1 | PIN, LOCK, M6 x 36, Slotted, 6 x 36 mm, if used, replaces 38-11620 pin |
| 44 | 221-841 | 1 | PLUG, hex socket, 1/4 inch PT, if used |
| 45 | 109088C4 | 2 | PIN, LARGE, leveling |
| 46 | 432-1620 | 2 | PIN, SPLIT (COTTER), 1/4″ x 1 1/4″, 1/4″ x 1 1/4″ |
| 47 | 242748A1 | 1 | HARDWARE, KIT – telescoping draft arm bolt, includes instructions |
| 49 | 495-81072 | 3 | WASHER, 1 1/32″ x 1 3/4″ x .030″ |
| 50 | 432-1624 | 1 | PIN, SPLIT (COTTER), 1/4″ x 1 1/2″ |
| 1 | 130316A1 | 1 | LINK DRAG, lower lift, left-hand front, not shown, no longer available, order 1331893C8 link |
| 1 | 130317A1 | 1 | LINK DRAG, lower lift, right-hand front, no longer available, order 1331894C8 link |
| 3 | 1282114C4 | 1 | LINK, LOWER, lift, left-hand rear, not shown |
| 3 | 1282115C4 | 1 | LINK, LOWER, lift, right-hand rear |
| 4 | 1286752C1 | 2 | BLOCK, BUMPER – cam |
| 5 | 70479C1 | 2 | SHIM, 1/32 inch, bumper |
| 6 | 70480C1 | 12 | SHIM, 1/16 inch, bumper |
| 7 | 1266811C1 | 2 | SPACER, cam bumper |
| 8 | 738-31260 | 2 | PIN, M12 x 60, Coiled, roll, 12 x 60 mm |
| 9 | 413-1280 | 2 | BOLT, Hex, 3/4″-10 x 5″, G5, hex, 3/4 NC x 5 inch |
| 10 | 231-14412 | 2 | NUT, LOCK, 3/4″-10, GB, hex, self-locking, 3/4 inch NC |
| 11 | 495-11081 | 2 | WASHER, 3/4″, SAE |
| 15 | 1347900C3 | 1 | SUPPORT ASSY., BRACKET ASSEMBLY – lower link, left-hand, not shown, includes Ref. 16 |
| 15 | 1347902C3 | 1 | SUPPORT ASSY., BRACKET ASSEMBLY – lower link, right-hand |
| 16 | 1960223C1 | 2 | BUSHING, bracket |
| 17 | 828-16090 | 2 | BOLT, Hex, M16 x 90, 10.9 |
| 18 | 896-16016 | 2 | WASHER, M16 x 34.5 x 5, HT, flat, 17.5 x 34 x 5 mm, hardened |
| 19 | 1347983C1 | 2 | BUSHING, LARGE, bracket |
| 20 | 614-10020 | 2 | BOLT, Hex, M10 x 20, 8.8, Full Thd |
| 26 | 1998150C1 | 2 | SPACER, cylinder mounting |
| 27 | 1998013C1 | 2 | BUSHING, cylinder |
| 28 | 145678C3 | 2 | WASHER, flat, 17 mm |
| 29 | 828-16160 | 2 | BOLT, Hex, M16 x 160, 10.9, BOLT – hex, 16 – 2.0 x 160 mm, class 10.9 |
| 30 | 495-81206 | 2 | WASHER, 1 9/32″ x 2 1/2″ x .120″, flat, 1-9/32 x 2-1/2 x 7/64 inch |
| 34 | 1347904C1 | 2 | PLATE, LARGE, sensing pin retaining |
| 35 | 895-18010 | 6 | WASHER, M10 x 18 x 1.6 |
| 36 | 614-10020 | 6 | BOLT, Hex, M10 x 20, 8.8, Full Thd |
| 40 | 828-24110 | 4 | BOLT, Hex, M24 x 110, 10.9, BOLT- hex, 24 – 3.0 x 110 mm, class 10.9 |
| 41 | 896-16024 | 4 | WASHER, M24 x 56.5 x 6, HT, flat, 26 x 56 x 6 mm |
| 45 | 398399R1 | 2 | LATCH, lower link |
| 46 | 382192R1 | 2 | SPRING, link latch |
| 47 | 382193R1 | 2 | SPRING, stiffener |
| 48 | 614-8012 | 2 | BOLT, Hex, M8 x 12, 8.8, Full Thd, Replaces 414-58 bolt |
| 49 | 125685A1 | 2 | PIN, LARGE, used with rigid lower link, if used |
| 50 | 627-10020 | 2 | BOLT, Hex, M10 x 20, 10.9, Full Thd |
| 51 | 896-11010 | 2 | WASHER, M10 x 21.5 x 2.5, HT |
| 52 | D95748 | 2 | SPACER, pin |
| 1 | 70-6430T1 | 1 | ATTACHMENT, HITCH – quick, coupler |
| 2 | 70-6452T1 | 1 | PIN, LARGE, mounting, 4-15/16 inch long, center link, replaces 70-4256T1 (6-3/4) inch long pin |
| 3 | 70-3082T2 | 3 | PLATE, LARGE, BLOCK – pin retaining |
| 4 | 426-816 | 6 | BOLT, Hex, 1/2″-13 x 1″, G8, Full Thd, BOLT – hex, 1/2 NC x 1 inch, grade 8 |
| 9 | 70-4320T1 | 2 | HANDLE, hitch release |
| 10 | 70-4324T1 | 2 | THREADED ROD, LINK – hitch release |
| 11 | 70-6310T2 | 2 | TRIGGER, LATCH – hitch release, replaces 70-631OT1 latch |
| 12 | 213-126 | 2 | CLEVIS, ADJUSTABLE, 3/8″-24 x 2 1/2″, adjustable, 3/8 inch NF |
| 13 | 427-6106 | 2 | PIN, CLEVIS, 3/8″ x 1 1/16″ |
| 14 | 432-616 | 4 | PIN, SPLIT (COTTER), 3/32″ x 1″ |
| 15 | 426-1072 | 4 | BOLT, Hex, 5/8″-11 x 4 1/2″, G8, BOLT – hex, 5/8 NC x 4-1/2 inch, grade 8 |
| 16 | 232-41110 | 4 | NUT, LOCK, 5/8″-11, GC |
| 17 | 70-4293T1 | 2 | PIN, LARGE, lower hitch |
| 18 | 425-156 | 2 | NUT, Jam, 3/8″-24, G5 |
| 19 | 19-5423 | 2 | PIN, LARGE, clevis, 3/8 x 7/8 inch |
| 20 | 70-4340T1 | 2 | SPRING, COMPRESSION, compression |
| 21 | 321-3339 | 1 | DECAL, Warning, be certain both latches are fully engaged across the implement lift pins, shown on |
| 23 | 229035A1 | 1 | PIN, LARGE, upper link |
| 24 | 64715C1 | 2 | HANDLE, hitch release |
| 25 | 427-5112 | 2 | PIN, CLEVIS, 5/16″ x 1 1/8″, PIN – clevis, 5/16 x 1-1/8 inch |
| 26 | 432-612 | 2 | PIN, SPLIT (COTTER), 3/32″ x 3/4″ |
| 27 | 326-840 | 8 | BOLT, Hex, 1/2″-13 x 2 1/2″, G8 |
| 28 | 392-11050 | 8 | WASHER, LOCK, 1/2″, 1/2″ |
| 29 | 329-108 | 8 | NUT, 1/2″-13, G8 |
| 30 | 229992A1 | 2 | LUG, LATCH – hitch release |
| 31 | 229990A1 | 2 | PIN, LARGE, roll, 1/2 x 2 inch |
| 32 | 229993A1 | 2 | PIN, LARGE, roll, 5/16 x 1 inch |
| 33 | 229994A1 | 2 | THREADED ROD, LINK – hitch release |
| 34 | 64717C1 | 2 | SPRING, compression |
| 35 | 229034A1 | 2 | PIN, LARGE, lower link |
| 36 | D33805 | 3 | PIN, locking |
| 37 | 321-3339 | 2 | DECAL, Warning, be certain both latches are fully engaged across the implement lift pins, shown on |
| 1 | 1286971C1 | 1 | PLATE ASSY., wear, drawbar |
| 2 | 67872C1 | 8 | WASHER, flat, 21/32 x 1-1/8 x 1/4 inch |
| 3 | 628-16050 | 2 | BOLT, Hex, M16 x 50, 10.9, Full Thd |
| 4 | 828-16190 | 6 | BOLT, Hex, M16 x 190, 10.9, BOLT – hex, 16 – 2.0 x 190 mm, class 10.9 |
| 5 | 1332004C1 | 1 | SPACER, wear, plate |
| 6 | 1981968C2 | 1 | SUPPORT, drawbar |
| 8 | 1331889C1 | 1 | CAM, sway limiter, left |
| 8 | 1331890C1 | 1 | CAM, sway limiter, right, shown |
| 9 | 410-11228 | 2 | BOLT, Locking, 3/4″-10 x 1 3/4″, G8, BOLT – hex, self-locking, 3/4 NC x 1-3/4 inch, grade 8 |
| 10 | 828-16060 | 4 | BOLT, Hex, M16 x 60, 10.9, Full Thd |
| 12 | 142619C3 | 1 | SUPPORT ASSY., pivot, drawbar |
| 13 | 837-25050 | 1 | DOWEL, M25 x 50, dowel, 25 x 50 mm, hardened |
| 14 | 896-16016 | 8 | WASHER, M16 x 34.5 x 5, HT, flat, 17.5 x 34 x 5 mm, hardened |
| 15 | 1286970C3 | 1 | DRAWBAR, swinging, replaces 1286970C2 drawbar |
| 16 | 1982103C1 | 1 | PIN, pivot, drawbar, 140 mm |
| 17 | 67828C1 | 1 | RETAINER, pin, drawbar |
| 20 | 1331986C1 | 1 | SPACER, pivot, drawbar |
| 21 | 627-12030 | 1 | BOLT, Hex, M12 x 30, 10.9, Full Thd |
| 22 | 892-11012 | 1 | WASHER, LOCK, M12 |
| 23 | 827-16140 | 2 | BOLT, Hex, M16 x 140, 10.9 |
| 24 | 832-10416 | 2 | NUT, LOCK, M16 x 2, Cl 8 |
| 25 | 1331943C1 | 1 | SUPPORT ASSY., chain |
| 26 | 827-20090 | 1 | BOLT, Hex, M20 x 90, 10.9 |
| 27 | 896-11020 | 1 | WASHER, M20 x 37.5 x 4, HT, flat, 22 x 37 x 4 mm, hardened |
| 28 | 829-1420 | 1 | NUT, M20, Cl 10 |
| 35 | 439-11236 | 2 | PIN, HEADED, 3/4″ x 2 1/4″, headed, 3/4 x 2-1/4 inch |
| 36 | 1978738C1 | 2 | PIN, SPLIT (COTTER), cotter, hair, 3/16 inch diameter |
| 1 | 142619C3 | 1 | SUPPORT ASSY., pivot, drawbar |
| 2 | 837-25050 | 1 | DOWEL, M25 x 50, dowel, 25 x 50 mm, hardened |
| 3 | 1982103C1 | 1 | PIN, pivot, drawbar |
| 4 | 67828C1 | 1 | RETAINER, pin, drawbar |
| 5 | 892-11012 | 1 | WASHER, LOCK, M12 |
| 6 | 627-12030 | 1 | BOLT, Hex, M12 x 30, 10.9, Full Thd |
| 7 | 896-16016 | 4 | WASHER, M16 x 34.5 x 5, HT, flat, 17.5 x 34 x 5 mm, hardened |
| 8 | 828-16060 | 4 | BOLT, Hex, M16 x 60, 10.9, Full Thd |
| 9 | 1348127C1 | 1 | BAR, DRAW – swinging |
| 10 | 827-16130 | 2 | BOLT, Hex, M16 x 130, 10.9, BOLT – hex, 16 – 2.0 x 130 mm, class 10.9 |
| 11 | 832-10416 | 2 | NUT, LOCK, M16 x 2, Cl 8 |
| 12 | 1982156C3 | 1 | SUPPORT, BRACKET – rear support |
| 13 | 1998066C1 | 2 | PIN, drawbar roller, replaces T38572 pin |
| 14 | 23443R1 | 4 | NUT, LOCK, 1″-8, GC, hex, 1 inch NC |
| 15 | 1982141C1 | 1 | PLATE, LARGE, rear support |
| 16 | A145831 | 2 | BUSHING, ROLLER – drawbar |
| 17 | 1982142C1 | 1 | PLATE, LARGE, front support |
| 18 | 219-14 | 2 | NIPPLE, LUBE, 1/4″ x .56″ lg, Drive, grease, straight, 1/4 drive type x 9/16 inch |
| 19 | 828-16065 | 8 | BOLT, Hex, M16 x 65, 10.9 |
| 20 | 896-16016 | 8 | WASHER, M16 x 34.5 x 5, HT, flat, 17.5 x 34 x 5 mm, hardened |
| 21 | 1286985C4 | 1 | PIN, HITCH, drawbar |
| 22 | 1286924C1 | 1 | SPACER, strap |
| 23 | 1331939C1 | 1 | SPACER, strap |
| 24 | 1331943C1 | 1 | SUPPORT ASSY., chain |
| 25 | 1348030C1 | 1 | BAR, STRAP – hammerstrap |
| 26 | 827-20200 | 1 | BOLT, Hex, M20 x 200, 10.9, BOLT – hex, 20 – 2.5 x 200 mm, class 10.9 |
| 27 | 827-20160 | 1 | BOLT, Hex, M20 x 160, 10. 9, BOLT – hex, 20 – 2.5 x 160 mm, class 10.9 |
| 28 | 896-11020 | 2 | WASHER, M20 x 37.5 x 4, HT, flat, 22 x 37 x 4 mm, hardened |
| 29 | 829-1420 | 2 | NUT, M20, Cl 10 |
| 30 | 1348043C1 | 1 | PIN, LARGE, klik, lock |
| 31 | 224619C2 | 1 | SPACER, drawbar pivot |
| 1 | 1286985C4 | 1 | PIN, HITCH, hammerstrap |
| 2 | 827-20200 | 1 | BOLT, Hex, M20 x 200, 10.9, BOLT – hex, 20 – 2.5 x 200 mm, class 10.9, if used |
| 2 | 827-20210 | 1 | BOLT, Hex, M20 x 210, 10.9, BOLT – hex, 20 – 2.5 x 210 mm, class 10.9, if used |
| 3 | 896-11020 | 2 | WASHER, M20 x 37.5 x 4, HT, flat, 22 x 37 x 4 mm, hardened |
| 4 | 829-1420 | 2 | NUT, M20, Cl 10 |
| 7 | 1286984C1 | 1 | DRAWBAR, HAMMERSTRAP |
| 9 | 827-20160 | 1 | BOLT, Hex, M20 x 160, 10. 9, BOLT – hex, 20 – 2.5 x 160 mm, class 10.9, if used |
| 9 | 827-20170 | 1 | BOLT, Hex, M20 x 170, 10.9, BOLT – hex, 20 – 2.5 x 170 mm, class 10.9, if used |
| 10 | 1286924C1 | 1 | SPACER, strap |
| 11 | 1331939C1 | 1 | SPACER, strap |
| 12 | 1965315C2 | 1 | LEVER, hammerstrap |
| 13 | 1965312C3 | 1 | LATCH ASSY., hammerstrap |
| 14 | 1965316C2 | 2 | BUSHING, latch |
| 15 | 827-12065 | 1 | BOLT, Hex, M12 x 65, 10.9, hex, 12 – 1.75 x 65 mm, class 10.9 |
| 16 | 832-10412 | 1 | NUT, LOCK, M12 x 1.75, Cl 8 |
| 18 | 1348043C1 | 1 | PIN, LARGE, klik, lock, special |
| 19 | 1331943C1 | 1 | SUPPORT ASSY., chain |
| 20 | A181436 | 1 | BOX, TOOL |
| 21 | A181434 | 1 | SUPPORT, BRACKET – mounting, tool box |
| 24 | 814-16150 | 2 | BOLT, Hex, M16 x 150, 8.8, BOLT – hex, 16 – 2.0 x 150 mm, tool box |
| 25 | 893-16016 | 2 | WASHER, LOCK, Int Tooth, M16, internal tooth lock, 16 mm, replaces 892-11016 lock washer, tool box |
| 26 | 895-11016 | 2 | WASHER, M16 x 30 x 3, flat, 17.5 x 30 x 3 mm, tool box |
| 27 | 825-1416 | 2 | NUT, M16, Cl 8, Toolbox |
| 28 | 1348536C1 | 2 | SPACER, mounting, tool box |
| 1 | 1334670C4 | 1 | SUPPORT, MOUNT – engine, right |
| 2 | 1334669C4 | 1 | SUPPORT, MOUNT – engine, left |
| 3 | 626-12035 | 6 | BOLT, Hex, M12 x 35, 10.9, Full Thd, BOLT – hex, full threads, 12 – 1.75 x 35 mm, class 10.9 |
| 4 | 896-15012 | 6 | WASHER, M12 x 28.5 x 4, HT, flat, 13.5 x 28 x 4 mm, hardened |
| 7 | 1960839C1 | 1 | SUPPORT, BRACKET – engine mount, right |
| 8 | 1960841C1 | 1 | SUPPORT, BRACKET – engine mount, left |
| 9 | 627-12040 | 4 | BOLT, Hex, M12 x 40, 10.9, Full Thd |
| 10 | 895-11012 | 4 | WASHER, M12 x 24 x 2.5, flat, 13.5 x 24 x 2.5 mm |
| 12 | 826-16100 | 2 | BOLT, Hex, M16 x 100, 10.9, BOLT – hex, M16, 10.9 |
| 13 | 96-81009 | 4 | WASHER, 11/16″ x 1 1/2″ x .134″, HDN |
| 14 | 825-1416 | 2 | NUT, M16, Cl 8 |
| 17 | 1289057C2 | 1 | RAIL, FRAME – side rail, right |
| 18 | 1289056C1 | 1 | RAIL, FRAME – side rail, left |
| 19 | 828-22305 | 2 | BOLT, Hex, M22 x 305, 10.9, BOLT – hex, 22 – 2.5 x 305 mm, class 10.9 |
| 20 | 1289069C1 | 4 | WASHER, flat, hardened, hardened |
| 21 | 828-22070 | 2 | BOLT, Hex, M22 x 70, 10.9, BOLT – hex, 22 – 2.5 x 70 mm, class 10.9 |
| 22 | 828-20070 | 2 | BOLT, Hex, M20 x 70, 10.9, Full Thd |
| 23 | A177650 | 4 | WASHER, flat, hardened |
| 26 | 828-16280 | 2 | BOLT, Hex, M16 x 280, 10.9, BOLT – hex, 16 – 2.0 x 280 mm, class 10.9 |
| 27 | 896-16016 | 2 | WASHER, M16 x 34.5 x 5, HT, flat, 17.5 x 34 x 5 mm, hardened |
| 28 | A169100 | 16 | BOLT, hex flange 16 – 2 x 45 mm, class 10.9 |
| 29 | 137316A3 | 1 | SUPPORT ASSY., BOLSTER – steering, front end, replaces A185918 support |
| 30 | 828-20070 | 2 | BOLT, Hex, M20 x 70, 10.9, Full Thd |
| 40 | 1955424C1 | 1 | PLATE, bolster cover, if used |
| 41 | 495-11053 | 2 | WASHER, 1/2″, SAE, (17/32″ x 1-1/16″ x 3/32″), If used |
| 42 | 614-10030 | 5 | BOLT, Hex, M10 x 30, 8.8, If used |
| 43 | 192896A1 | 4 | PLUG, front support, if used |
| 44 | 225151A1 | 1 | PROTECTION PLATE, PLATE – bolster cover, if used |
| 45 | 864-10016 | 2 | SCREW, Hex Soc Hd, M10 x 16, 8.8, If used |
| 46 | 895-15010 | 2 | WASHER, M11 x 24 x 2, If Used |
| 1 | 1342125C3 | 1 | SUPPORT, FRAME – front weight (Maximum of 18 weights) (Used with MFD or standard axle) |
| 2 | 827-20065 | 6 | BOLT, Hex, M20 x 65, 10.9, Full Thd |
| 3 | 896-11020 | 6 | WASHER, M20 x 37.5 x 4, HT, flat, 22 x 37 x 4 mm, hardened |
| 5 | 1342127C2 | 1 | SUPPORT, FRAME – front weight (Maximum of 22 weights) (Not used with MFD) |
| 6 | 827-20065 | 6 | BOLT, Hex, M20 x 65, 10.9, Full Thd |
| 7 | 896-11020 | 6 | WASHER, M20 x 37.5 x 4, HT, flat, 22 x 37 x 4 mm, hardened |
| 9 | 1347524C1 | 6 | WEIGHT, front, order 1348233C1 or A67894 weight from Machinery Price List, 45.36 kgs, (100 pound) |
| 10 | 1347524C1 | 22 | WEIGHT, front, order 1348233C1 or A67894 weight from Machinery Price List, 45.36 kgs, (100 pound) |
| 11 | 1978431C1 | 3 | CLAMP, weight |
| 12 | A169139 | 3 | BOLT, square head, special, 1/2 NC x 3-1/4 inch |
| 13 | 495-11053 | 3 | WASHER, 1/2″, SAE, (17/32″ x 1-1/16″ x 3/32″) |
| 14 | 80679 | 3 | WASHER, LOCK, 1/2″ |
| 15 | 425-108 | 3 | NUT, 1/2″-13, G5 |
| 1 | 1334382C4 | 1 | SUPPORT, hood, front |
| 2 | 413-620 | 4 | BOLT, Hex, 3/8″-16 x 1 1/4″, G5, Full Thd, hex, 3/8 NC x 1-1/4 inch |
| 5 | 1348511C1 | 1 | SUPPORT ASSY., CHANNEL – hood, right, shown |
| 5 | 1348512C1 | 1 | SUPPORT ASSY., CHANNEL – hood, left |
| 7 | 413-616 | 6 | BOLT, Hex, 3/8″-16 x 1″, G5, Full Thd, hex, 3/8 NC x 1 inch |
| 12 | A145743 | 2 | MOUNTING PARTS, radiator upper, rubber |
| 13 | 495-21031 | 2 | WASHER, 1/4″, flat, 5/16 x 3/4 x 1/16 inch |
| 14 | 492-11025 | 2 | WASHER, LOCK, 1/4″ |
| 15 | 425-104 | 2 | NUT, 1/4″-20, G5 |
| 18 | 1334474C1 | 2 | BRACKET, side panel support |
| 19 | 811-10025 | 4 | BOLT, CARRIAGE, Short NK, M10 x 25, Cl8.8, Full Thd |
| 20 | 829-2410 | 4 | NUT, M10 x 1.5, Flg, Cl 10 |
| 21 | 1334565C4 | 1 | SUPPORT ASSY., side panel |
| 22 | 1289062C2 | 1 | SUPPORT ASSY., hood release, left |
| 23 | 862-10020 | 2 | SCREW, Hex Soc Hd, M10 x 20, 12.9, BOLT – hex socket, 10 – 1.5 x 20 mm, class 12.9 |
| 24 | 829-2410 | 2 | NUT, M10 x 1.5, Flg, Cl 10 |
| 26 | 1334564C2 | 1 | SUPPORT, BRACKET – side panel, left-hand, rear support |
| 27 | 811-10025 | 4 | BOLT, CARRIAGE, Short NK, M10 x 25, Cl8.8, Full Thd |
| 28 | 829-2410 | 4 | NUT, M10 x 1.5, Flg, Cl 10 |
| 29 | 862-10020 | 2 | SCREW, Hex Soc Hd, M10 x 20, 12.9, BOLT – hex socket, 10 – 1.5 x 20 mm, class 12.9 |
| 30 | 829-2410 | 4 | NUT, M10 x 1.5, Flg, Cl 10 |
| 31 | 1289064C1 | 1 | SUPPORT ASSY., hood release, right |
| 32 | 614-12030 | 4 | BOLT, Hex, M12 x 30, 8.8, Full threads |
| 33 | 892-11012 | 4 | WASHER, LOCK, M12 |
| 34 | 1340550C2 | 1 | SUPPORT, hood, rear |
| 35 | 1340604C1 | 1 | HANDLE, hood release |
| 36 | 1960805C4 | 1 | BRACKET, screen latch, inner, right |
| 37 | 1340590C1 | 1 | SUPPORT, BRACKET – screen latch, inner, left |
| 38 | 614-8020 | 1 | BOLT, Hex, M8 x 20, 8.8 |
| 38 | 892-11008 | 1 | WASHER, LOCK, M8 |
| 39 | 895-11008 | 1 | WASHER, M8 x 16 x 1.6 |
| 40 | 1968039C3 | 2 | FASTENER, RECEIVER – screen, latch stud |
| 41 | 260-5448 | 4 | SCREW, SELF TAPPING, Cross Pan Hd, #8 x 1/2″, Phillips |
| 42 | 495-21019 | 4 | WASHER, #8 |
| 45 | 614-10025 | 2 | BOLT, Hex, M10 x 25, 8.8, Full Thd |
| 46 | A169954 | 2 | BUSHING, hood release |
| 47 | 892-11010 | 2 | WASHER, LOCK, M10 |
| 48 | 825-1410 | 2 | NUT, M10, Cl 8 |
| 55 | 825-2308 | 2 | NUT, M8 x 1.25, Flg, Cl 8, hex, flange, 8 mm – 1.25 |
| 56 | 892-11010 | 4 | WASHER, LOCK, M10 |
| 57 | 413-520 | 2 | BOLT, Hex, 5/16″-18 x 1 1/4″, G5, hex, 5/16 NC x 1-1/4 inch |
| 58 | 425-105 | 2 | NUT, 5/16″-18, G5 |
| 59 | 116292A1 | 1 | SUPPORT, BRACKET – right-hand side panel, rear |
| 60 | A176570 | 1 | SPACER, bracket |
| 61 | 814-10060 | 1 | BOLT, Hex, M10 x 60, 8.8 |
| 62 | 895-11010 | 1 | WASHER, M10 x 20 x 2 |
| 63 | 905-10020 | 1 | BOLT, Hex Serr Flg, M10 x 20, Side panel bracket |
| 1 | 140668A2 | 1 | FRAME, SUPPORT – hood and radiator |
| 2 | 844-10065 | 4 | BOLT, Hex Flg, M10 x 65, 8.8, BOLT – heavy hex flange, 10 – 1.5 x 65 mm |
| 19 | 811-10025 | 4 | BOLT, CARRIAGE, Short NK, M10 x 25, Cl8.8, Full Thd |
| 20 | 829-2410 | 4 | NUT, M10 x 1.5, Flg, Cl 10 |
| 21 | 188762A1 | 1 | SUPPORT ASSY., side panel, left rear |
| 22 | 1289062C2 | 1 | SUPPORT ASSY., hood release, left |
| 23 | 864-10020 | 2 | SCREW, Hex Soc Hd, M10 x 20, 8.8 |
| 24 | 829-2410 | 2 | NUT, M10 x 1.5, Flg, Cl 10 |
| 26 | 1334564C2 | 1 | SUPPORT, BRACKET – side panel, left-hand, rear support |
| 29 | 864-10020 | 4 | SCREW, Hex Soc Hd, M10 x 20, 8.8 |
| 30 | 829-2410 | 2 | NUT, M10 x 1.5, Flg, Cl 10 |
| 31 | 1289064C1 | 1 | SUPPORT ASSY., hood release, right |
| 32 | 614-12030 | 4 | BOLT, Hex, M12 x 30, 8.8, Full threads |
| 33 | 892-11012 | 4 | WASHER, LOCK, M12 |
| 34 | 142187A1 | 1 | SUPPORT, hood release |
| 35 | 1340604C1 | 1 | HANDLE, hood release |
| 36 | 1960805C4 | 1 | BRACKET, screen latch, inner, right |
| 37 | 1340590C1 | 1 | SUPPORT, BRACKET – screen latch, inner, left |
| 38 | 614-8020 | 1 | BOLT, Hex, M8 x 20, 8.8 |
| 38 | 892-11008 | 1 | WASHER, LOCK, M8 |
| 39 | 895-11008 | 1 | WASHER, M8 x 16 x 1.6 |
| 40 | 1968039C3 | 2 | FASTENER, RECEIVER – screen, latch stud |
| 41 | 260-5448 | 4 | SCREW, SELF TAPPING, Cross Pan Hd, #8 x 1/2″, Phillips |
| 42 | 495-21019 | 4 | WASHER, #8 |
| 45 | 614-10025 | 2 | BOLT, Hex, M10 x 25, 8.8, Full Thd |
| 46 | A169954 | 2 | BUSHING, hood release |
| 47 | 892-11010 | 2 | WASHER, LOCK, M10 |
| 48 | 825-1410 | 2 | NUT, M10, Cl 8 |
| 55 | 825-2308 | 2 | NUT, M8 x 1.25, Flg, Cl 8, hex, flange, 8 mm – 1.25 |
| 56 | 892-11010 | 2 | WASHER, LOCK, M10 |
| 57 | 413-520 | 2 | BOLT, Hex, 5/16″-18 x 1 1/4″, G5, hex, 5/16 NC x 1-1/4 inch |
| 58 | 425-105 | 2 | NUT, 5/16″-18, G5 |
| 59 | 116292A2 | 1 | SUPPORT, BRACKET – right-hand side panel, rear support, replaces 116292A1 bracket |
| 60 | A176570 | 1 | SPACER, bracket |
| 61 | 905-10060 | 1 | BOLT, Hex Serr Flg, M10 x 60, BOLT – hex serrated flange, 10 – 1.5 x 60 mm |
| 62 | 895-11010 | 1 | WASHER, M10 x 20 x 2, If used |
| 63 | 905-10020 | 1 | BOLT, Hex Serr Flg, M10 x 20, Side panel bracket |
| 64 | 1334474C1 | 2 | BRACKET, side panel support |
| 1 | 1348364C1 | 1 | SILL, FRAME – hood side, right, shown |
| 1 | 1348455C1 | 1 | SILL, FRAME – hood side, left |
| 3 | 1348355C1 | 1 | PANEL ASSY., hood, upper right, shown |
| 3 | 1289341C2 | 1 | PANEL ASSY., hood, upper left |
| 6 | 1334318C1 | 1 | SEAL – foam, adhesive back, 343 mm (13-1/2 inch) long, cut from 252768A1 bulk seal, upper grille |
| 6 | 1334317C2 | 1 | SEAL, foam, adhesive back, 343 mm (13-1/2 inch) long, cut from 252768A1 bulk seal, upper grille |
| 7 | 1289074C2 | 1 | HOUSING, upper grille |
| 8 | 1348428C1 | 1 | SEAL, foam, adhesive back, 1042 mm (41 inch) long, cut from 252768A1 bulk seal, upper grille |
| 10 | 413-412 | 2 | BOLT, Hex, 1/4″-20 x 3/4″, G5, Full Thd |
| 11 | 495-21031 | 20 | WASHER, 1/4″, flat, 5/16 x 3/4 x 1/16 inch |
| 12 | 231-1444 | 20 | NUT, LOCK, 1/4″-20, GB |
| 13 | 1976792C1 | 1 | SIEVE, SCREEN – grille, upper |
| 14 | A147030 | 2 | SPACER, SPACER – grille screen |
| 15 | 1289314C1 | 1 | PANEL ASSY., HOOD – top center |
| 16 | 495-21031 | 18 | WASHER, 1/4″, flat, 5/16 x 3/4 x 1/16 inch |
| 17 | 231-1444 | 18 | NUT, LOCK, 1/4″-20, GB |
| 26 | 413-412 | 6 | BOLT, Hex, 1/4″-20 x 3/4″, G5, Full Thd |
| 28 | 495-21031 | 12 | WASHER, 1/4″, flat, 5/16 x 3/4 x 1/16 inch |
| 29 | 231-1444 | 6 | NUT, LOCK, 1/4″-20, GB |
| 30 | 1289322C1 | 1 | HOUSING, COVER – hood, to cab transition, right, shown |
| 30 | 1289321C1 | 1 | HOUSING, COVER – hood, to cab transition, left |
| 32 | 1974411C1 | 2 | PANEL, decal |
| 33 | 495-21038 | 20 | WASHER, 5/16″, flat, 3/8 x 7/8 x 3/32 inch |
| 34 | 131-205 | 20 | NUT, LOCK, 5/16″-18, heavy hex, self-locking, 5/16 inch NC |
| 35 | 1342160C1 | 1 | SEAL, SPECIAL MAT, hood to radiator |
| 36 | 1968082C1 | 2 | SEAL ASSY., hood to radiator corner |
| 37 | 1342164C1 | 1 | SEAL, SPECIAL MAT, hood to radiator |
| 39 | 493-11026 | 10 | WASHER, LOCK, Ext-Int Tooth, 1/4″, internal-external tooth lock, 1/4 inch |
| 9 | 413-420 | 2 | BOLT, Hex, 1/4″-20 x 1 1/4″, G5 |
| 1 | 1348364C1 | 1 | SILL, FRAME – hood side, right, shown |
| 1 | 1348455C1 | 1 | SILL, FRAME – hood side, left |
| 3 | 1348355C1 | 1 | PANEL ASSY., hood, upper right, shown |
| 3 | 1289341C2 | 1 | PANEL ASSY., hood, upper left |
| 6 | 1334317C2 | 2 | SEAL, foam, adhesive back, 343 mm (13-1/2 inch) long, cut from 252768A1 bulk seal, upper grille |
| 7 | 142870A1 | 1 | HOUSING, upper grille |
| 8 | 1348428C2 | 1 | SEAL, foam, adhesive back, 1042 mm (41 inch) long, cut from 252768A1 bulk seal, upper grille |
| 10 | 413-412 | 2 | BOLT, Hex, 1/4″-20 x 3/4″, G5, Full Thd |
| 11 | 495-21031 | 20 | WASHER, 1/4″, flat, 5/16 x 3/4 x 1/16 inch |
| 12 | 231-1444 | 20 | NUT, LOCK, 1/4″-20, GB |
| 13 | 192169A1 | 1 | SIEVE, SCREEN – grille, upper |
| 14 | A147030 | 2 | SPACER, SPACER – grille screen |
| 15 | 181461A1 | 1 | PANEL ASSY., HOOD – top center, screen |
| 16 | 495-21031 | 18 | WASHER, 1/4″, flat, 5/16 x 3/4 x 1/16 inch |
| 17 | 231-1444 | 18 | NUT, LOCK, 1/4″-20, GB |
| 26 | 413-412 | 6 | BOLT, Hex, 1/4″-20 x 3/4″, G5, Full Thd |
| 28 | 495-21031 | 12 | WASHER, 1/4″, flat, 5/16 x 3/4 x 1/16 inch |
| 29 | 231-1444 | 6 | NUT, LOCK, 1/4″-20, GB |
| 30 | 1289322C1 | 1 | HOUSING, COVER – hood, to cab transition, right, shown |
| 30 | 1289321C1 | 1 | HOUSING, COVER – hood, to cab transition, left |
| 32 | 141863A1 | 1 | PANEL, decal, left-hand, not shown |
| 32 | 141862A1 | 1 | PANEL, decal, right-hand, shown |
| 33 | 495-21038 | 16 | WASHER, 5/16″, flat, 3/8 x 7/8 x 3/32 inch |
| 34 | 131-205 | 16 | NUT, LOCK, 5/16″-18, heavy hex, self-locking, 5/16 inch NC |
| 36 | 137886A1 | 2 | SEAL, foam, adhesive back, 19 (3/4) x 19 (3/4) x 80 mm (3-5/32 inch) long, hood to radiator corner |
| 37 | 141857A1 | 1 | SEAL, SPECIAL MAT, foam, adhesive back, 120 (4-3/4) x 19 (3/4) x 1168 mm (46 inch) long, hood to |
| 39 | 493-11026 | 10 | WASHER, LOCK, Ext-Int Tooth, 1/4″, internal-external tooth lock, 1/4 inch |
| 40 | 181045A1 | 1 | SCREEN, front, Magnum |
| 9 | 413-420 | 2 | BOLT, Hex, 1/4″-20 x 1 1/4″, G5 |
| 1 | 105506A1 | 1 | PANEL ASSY., screen, hood, lower right side, includes item 36 |
| 3 | 122967A1 | 1 | SUPPORT, side panel, right |
| 4 | 1960793C5 | 1 | PROTECTION PLATE, SCREEN – hood, side right |
| 8 | 1993508C1 | 2 | SEAL, lower side panel, front |
| 9 | 1974407C2 | 2 | SEAL, lower side panel |
| 10 | 1960849C1 | 2 | BRACKET, screen latch outer |
| 11 | 614-6016 | 2 | BOLT, Hex, M6 x 16, 8.8 |
| 12 | 825-2406 | 2 | NUT, M6 x 1, Flg, Cl 8 |
| 14 | 463-61010 | 2 | SCREW, Hex Hd, #10-32 x 5/8″, machine, hex head, No. 10 NF x 5/8 inch |
| 18 | 1348429C1 | 2 | SEAL, lower side panels, top, 15-3/16 inch (386 mm) long, cut from 252768A1 bulk seal |
| 19 | 105505A1 | 1 | PANEL ASSY., screen, hood front low, includes item 36 |
| 20 | 1289399C3 | 1 | PANEL ASSY., hood, rear lower side left |
| 21 | 122969A1 | 1 | SUPPORT, side panel, left |
| 22 | 1348384C1 | 1 | HINGE, side panel, front, left |
| 23 | 1348383C1 | 1 | HINGE, side panel, rear, left |
| 24 | 1968038C3 | 1 | SUPPORT ASSY., latch outer |
| 25 | 1960792C5 | 1 | PROTECTION PLATE, SCREEN – hood side, left |
| 26 | 463-61010 | 2 | SCREW, Hex Hd, #10-32 x 5/8″, machine, hex head, No. 10 NF x 5/8 inch |
| 27 | 1960763C3 | 2 | FASTENER, RECEIVER – left rear side panel stud |
| 28 | 263-5448 | 4 | SCREW, SELF TAPPING, Slotted Pan Hd, #8 x 1/2″, self-tapping, pan slotted, No. 8-18 x 1/2 inch, if |
| 29 | 495-21019 | 4 | WASHER, #8 |
| 30 | A149863 | 1 | GUIDE, left rear side panel |
| 31 | 492-11025 | 1 | WASHER, LOCK, 1/4″ |
| 32 | 425-104 | 1 | NUT, 1/4″-20, G5 |
| 33 | 1968137C1 | 1 | PLATE ASSY., latch, outer rear, no longer required |
| 35 | 1348465C1 | 2 | STUD, rear side panel latch |
| 36 | 1348479C1 | 2 | FOAM, STRIP – wear, 517 mm (20-3/8 inch) long, cut from 1348532C1X bulk strip, not shown |
| 1 | 128014A1 | 1 | PANEL ASSY., hood, screen, lower right side, includes item 36 |
| 3 | 122967A1 | 1 | SUPPORT, side panel, right |
| 4 | 1960793C5 | 1 | PROTECTION PLATE, SCREEN – hood, side right |
| 10 | 1960849C1 | 2 | BRACKET, screen latch outer |
| 11 | 614-6016 | 2 | BOLT, Hex, M6 x 16, 8.8 |
| 12 | 825-2406 | 2 | NUT, M6 x 1, Flg, Cl 8 |
| 14 | 463-61010 | 2 | SCREW, Hex Hd, #10-32 x 5/8″, machine, hex head, No. 10 NF x 5/8 inch |
| 18 | 1348429C1 | 2 | SEAL, lower side panels, top, 15-3/16 inch (386 mm) long, cut from 252768A1 bulk seal |
| 19 | 195934A1 | 1 | PANEL ASSY., screen, hood, front low, includes item 36 |
| 20 | 1289399C3 | 1 | PANEL ASSY., hood, rear lower side left |
| 21 | 122969A1 | 1 | SUPPORT, side panel, left |
| 22 | 194873A1 | 1 | HINGE, side panel, front, left |
| 23 | 192284A1 | 1 | HINGE, side panel, rear, left |
| 24 | 1968038C3 | 1 | SUPPORT ASSY., latch outer |
| 25 | 1960792C5 | 1 | PROTECTION PLATE, SCREEN – hood side, left |
| 26 | 463-61010 | 2 | SCREW, Hex Hd, #10-32 x 5/8″, machine, hex head, No. 10 NF x 5/8 inch |
| 27 | 1960763C3 | 2 | FASTENER, RECEIVER – left rear side panel stud |
| 28 | 260-5448 | 4 | SCREW, SELF TAPPING, Cross Pan Hd, #8 x 1/2″, Phillips |
| 29 | 495-21019 | 4 | WASHER, #8 |
| 30 | A149863 | 1 | GUIDE, left rear side panel |
| 31 | 492-11025 | 1 | WASHER, LOCK, 1/4″ |
| 32 | 425-104 | 1 | NUT, 1/4″-20, G5 |
| 35 | 1348465C1 | 2 | STUD, rear side panel latch |
| 36 | 1348479C1 | 2 | FOAM, STRIP – wear, 517 mm (20-3/8 inch) long, cut from 1348532C1X bulk strip, not shown |
| 1 | 1968100C3 | 4 | LINK DRAG, ASSEMBLY – hood tilt |
| 2 | A59809 | 2 | BUSHING, hood tilt link |
| 3 | 1334698C4 | 1 | SUPPORT, BRACKET – hinge support, right |
| 4 | 1334697C4 | 1 | SUPPORT, BRACKET – hinge support, left |
| 5 | 131-425 | 8 | NUT, LOCK, Push, 1/2″, push-on type, 1/2 inch |
| 6 | 627-12040 | 4 | BOLT, Hex, M12 x 40, 10.9, Full Thd |
| 7 | 1976756C2 | 4 | WASHER, flat, hinge |
| 8 | A185252 | 1 | LEVER, hood lock |
| 9 | 100-11100 | 1 | RING, SNAP, #100, Ext, Hood lock lever |
| 10 | 495-81147 | 2 | WASHER, 13/32″ x 2″ x .109″, flat, 13/32 x 2 x 1/8 inch |
| 11 | 413-620 | 1 | BOLT, Hex, 3/8″-16 x 1 1/4″, G5, Full Thd, hex, 3/8 NC x 1-1/4 inch |
| 12 | 131-206 | 1 | NUT, LOCK, 3/8″-16, heavy hex, self-locking, 3/8 inch NC |
| 13 | 1348231C1 | 1 | HANDLE, GRIP – hood |
| 14 | 1960835C3 | 1 | SUPPORT, BRACE – hood, center and cylinder |
| 16 | 495-81286 | 3 | WASHER, .281″ x 1 1/8″ x .060″, flat, 9/32 x 1-1/8 x 1/16 inch |
| 17 | 231-1444 | 3 | NUT, LOCK, 1/4″-20, GB |
| 18 | 892-11012 | 4 | WASHER, LOCK, M12 |
| 19 | 829-1412 | 4 | NUT, M12, Cl 10 |
| 25 | 1968168C3 | 2 | GAS STRUT, CYLINDER ASSEMBLY – hood tilt |
| 27 | 3234063R1 | 4 | BALL JOINT, STUD |
| 28 | 3233348R1 | 4 | CLIP, retaining, ball stud |
| 29 | 892-11010 | 4 | WASHER, LOCK, M10 |
| 30 | 825-1410 | 4 | NUT, M10, Cl 8 |
| 31 | 1289137C1 | 1 | BRACE, hood support, rear |
| 32 | 413-528 | 2 | BOLT, Hex, 5/16″-18 x 1 3/4″, G5, hex, 5/16 NC x 1-3/4 inch |
| 33 | 425-105 | 2 | NUT, 5/16″-18, G5 |
| 37 | A147728 | 2 | TRIGGER, LATCH – hood lock |
| 38 | 1978450C2 | 2 | SPRING, hood lock |
| 39 | 231-1444 | 5 | NUT, LOCK, 1/4″-20, GB |
| 40 | 413-452 | 2 | BOLT, Hex, 1/4″-20 x 3 1/4″, G5, BOLT – hex, 1/4 NC x 3-1/4 inch |
| 42 | 495-21031 | 2 | WASHER, 1/4″, flat, 5/16 x 3/4 x 1/16 inch |
| 43 | 495-81286 | 3 | WASHER, .281″ x 1 1/8″ x .060″, flat, 9/32 x 1-1/8 x 1/16 inch |
| 44 | 1289381C2 | 1 | SEAL – foam, adhesive back, 862 mm (33-15/16 inch) long, cut from 1348430C1 bulk seal, lower |
| 45 | 105509A1 | 1 | HOUSING, lower grille |
| 47 | 112994A1 | 1 | ANGLE, grille support, right, shown |
| 48 | 112995A1 | 1 | ANGLE, grille support, left |
| 49 | A147030 | 8 | SPACER, SPACER – grille screen |
| 50 | 413-612 | 4 | BOLT, Hex, 3/8″-16 x 3/4″, G5, Full Thd, hex, 3/8 NC x 3/4 inch |
| 51 | 492-11038 | 4 | WASHER, LOCK, 3/8″ |
| 52 | 495-81147 | 4 | WASHER, 13/32″ x 2″ x .109″, flat, 13/32 x 2 x 1/8 inch |
| 53 | 231-1444 | 4 | NUT, LOCK, 1/4″-20, GB |
| 54 | 1976793C4 | 1 | SCREEN, lower grille, replaces 1976793C2 screen |
| 55 | 495-21031 | 12 | WASHER, 1/4″, flat, 5/16 x 3/4 x 1/16 inch |
| 56 | 231-1444 | 12 | NUT, LOCK, 1/4″-20, GB |
| 15 | 413-420 | 3 | BOLT, Hex, 1/4″-20 x 1 1/4″, G5 |
| 41 | 413-420 | 3 | BOLT, Hex, 1/4″-20 x 1 1/4″, G5 |
| 1 | 1968100C3 | 4 | LINK DRAG, ASSEMBLY – hood tilt |
| 2 | A59809 | 2 | BUSHING, hood tilt link |
| 3 | 141465A2 | 1 | SUPPORT, BRACKET – hinge support, right |
| 4 | 141467A2 | 1 | SUPPORT, BRACKET – hinge support, left |
| 5 | 131-425 | 8 | NUT, LOCK, Push, 1/2″, push-on type, 1/2 inch |
| 8 | A185252 | 1 | LEVER, hood lock |
| 9 | 100-11100 | 1 | RING, SNAP, #100, Ext, Hood lock lever, replaces B18208 ring |
| 10 | 495-81147 | 2 | WASHER, 13/32″ x 2″ x .109″, flat, 13/32 x 2 x 1/8 inch |
| 11 | 413-620 | 1 | BOLT, Hex, 3/8″-16 x 1 1/4″, G5, Full Thd, hex, 3/8 NC x 1-1/4 inch |
| 12 | 131-206 | 1 | NUT, LOCK, 3/8″-16, heavy hex, self-locking, 3/8 inch NC |
| 13 | 1348231C1 | 1 | HANDLE, GRIP – hood handle |
| 14 | 181030A1 | 1 | SUPPORT, BRACE – hood, cylinder |
| 16 | 495-81286 | 3 | WASHER, .281″ x 1 1/8″ x .060″, flat, 9/32 x 1-1/8 x 1/16 inch |
| 17 | 231-1444 | 3 | NUT, LOCK, 1/4″-20, GB |
| 18 | 829-1412 | 4 | NUT, M12, Cl 10 |
| 19 | 892-11012 | 4 | WASHER, LOCK, M12 |
| 20 | 614-12110 | 4 | BOLT, Hex, M12 x 110, 8.8, Full Thd, BOLT – hex, full threads, 1.2 – 1.75 x 10 mm |
| 21 | 829-2312 | 12 | NUT, M12 x 1.75, Flg, Cl 10, hex flange, 12 mm – 1.75, class 10 |
| 23 | 832-10408 | 2 | NUT, LOCK, M8 x 1.25, Cl 8 |
| 25 | 1968168C3 | 2 | GAS STRUT, CYLINDER ASSEMBLY – hood tilt |
| 27 | 142597A1 | 4 | STUD, ball |
| 28 | 3233348R1 | 4 | CLIP, retaining, ball stud |
| 29 | 892-11010 | 4 | WASHER, LOCK, M10 |
| 30 | 825-1410 | 4 | NUT, M10, Cl 8 |
| 31 | 1289137C1 | 1 | BRACE, hood support, rear |
| 32 | 413-528 | 2 | BOLT, Hex, 5/16″-18 x 1 3/4″, G5, hex, 5/16 NC x 1-3/4 inch |
| 33 | 425-105 | 2 | NUT, 5/16″-18, G5 |
| 37 | A147728 | 2 | TRIGGER, LATCH – hood lock |
| 38 | 1978450C2 | 2 | SPRING, hood lock |
| 39 | 231-1444 | 5 | NUT, LOCK, 1/4″-20, GB |
| 40 | 413-452 | 2 | BOLT, Hex, 1/4″-20 x 3 1/4″, G5, BOLT – hex, 1/4 NC x 3-1/4 inch |
| 42 | 495-21031 | 2 | WASHER, 1/4″, flat, 5/16 x 3/4 x 1/16 inch |
| 43 | 495-81286 | 3 | WASHER, .281″ x 1 1/8″ x .060″, flat, 9/32 x 1-1/8 x 1/16 inch |
| 44 | 1348428C2 | 1 | SEAL, foam, adhesive back, 1042 mm (41 inch) long, cut from 252768A1 bulk seal, lower housing |
| 45 | 179095A1 | 1 | HOUSING, lower grille |
| 47 | 141564A2 | 1 | ANGLE, grille support, right, shown |
| 48 | 141565A2 | 1 | ANGLE, grille support, left |
| 49 | A147030 | 12 | SPACER, SPACER – grille screen |
| 50 | 814-10060 | 2 | BOLT, Hex, M10 x 60, 8.8 |
| 51 | 892-11010 | 4 | WASHER, LOCK, M10 |
| 52 | 495-81147 | 4 | WASHER, 13/32″ x 2″ x .109″, flat, 13/32 x 2 x 1/8 inch |
| 53 | 231-1444 | 4 | NUT, LOCK, 1/4″-20, GB |
| 54 | 825-1410 | 4 | NUT, M10, Cl 8 |
| 55 | 192170A1 | 1 | GRILLE, SCREEN – lower |
| 56 | 495-21031 | 12 | WASHER, 1/4″, flat, 5/16 x 3/4 x 1/16 inch |
| 57 | 231-1444 | 12 | NUT, LOCK, 1/4″-20, GB |
| 58 | 495-81132 | 2 | WASHER, 13/32″ x 7/8″ x .179″, flat, 13/32 x 7/8 x 5/32 inch |
| 15 | 413-420 | 3 | BOLT, Hex, 1/4″-20 x 1 1/4″, G5 |
| 41 | 413-420 | 3 | BOLT, Hex, 1/4″-20 x 1 1/4″, G5 |
| 1 | 1348227C1 | 1 | COVER ASSY, filter, hydraulic |
| 2 | 1348228C1 | 1 | ANGLE, hydraulic filter cover mounting, no longer available, order 248933A1 below |
| 3 | 1975782C1 | 4 | SCREW, SELF TAPPING, Cross Truss Wash Hd, #10 x 5/8″ |
| 4 | 104036C1 | 4 | NUT, expansion, No. 10 |
| 5 | 1348243C1 | 1 | SUPPORT, mounting, filter cover |
| 6 | 1348244C1 | 1 | SUPPORT, hydraulic filter cover support |
| 8 | 614-6020 | 1 | BOLT, Hex, M6 x 20, 8.8, Full threads |
| 9 | 893-11006 | 3 | WASHER, LOCK, Ext Tooth, M6 |
| 10 | 832-10406 | 3 | NUT, LOCK, M6 x 1, Cl 8 |
| 12 | 1334657C1 | 1 | PLATE, LARGE, cover, models without lower flood lamp |
| 13 | 1960750C1 | 3 | SCREW, special, 1/4 NC x 3/8 inch |
| 14 | 231-5144 | 3 | NUT, Flg, USR, 1/4″-20, Not shown |
| 15 | 626-12035 | 2 | BOLT, Hex, M12 x 35, 10.9, Full Thd, BOLT – hex, full threads, 12 – 1.75 x 35 mm, class 10.9 |
| 16 | 895-11006 | 4 | WASHER, M6 |
| 19 | 97006C1 | 1 | BOLT, BOLT – hex flange, special, 6 – 1 x 20 mm, replaces 614-6025 bolt |
| 21 | 495-81286 | 1 | WASHER, .281″ x 1 1/8″ x .060″, flat, 9/32 x 1-1/8 x 1/16 inch, hardened |
| 23 | 628-12020 | 2 | BOLT, Hex, M12 x 20, 10.9, Full Thd, BOLT – hex, full threads, 12 – 1.75 x 20 mm, class 10.9 |
| 24 | 896-11012 | 4 | WASHER, M13.5 x 24.5 x 3, HT |
| 25 | 829-1412 | 1 | NUT, M12, Cl 10 |
| 1 | 1340591C1 | 2 | BRACKET, fender mounting, front, MFD |
| 2 | 495-11066 | 8 | WASHER, 5/8″, SAE, flat, 21/32 x 1-5/16 x 3/32 inch, MFD front fenders |
| 3 | 413-1048 | 8 | BOLT, Hex, 5/8″-11 x 3″, G5, hex, 5/8 NC x 3 inch, MFD front fenders |
| 4 | 814-16110 | 4 | BOLT, Hex, M16 x 110, 8.8, MFD front fenders |
| 5 | 1340558C1 | 4 | SPACER, fender brace, front, MFD |
| 6 | 1340675C1 | 1 | SUPPORT, BRACE – fender support, right, shown, front, MFD |
| 6 | 1340676C1 | 1 | SUPPORT, BRACE – fender support, left, front, MFD |
| 7 | 896-11016 | 4 | WASHER, M17.5 x 30 x 4, HT, MFD front fenders |
| 8 | 832-10416 | 4 | NUT, LOCK, M16 x 2, Cl 8, MFD Front fenders |
| 11 | 1340671C1 | 2 | SUPPORT, fender, inner, front, MFD |
| 12 | 495-21056 | 4 | WASHER, 1/2″, flat, 9/16 x 1-3/8 x 7/64 inch, MFD front fenders |
| 13 | 80679 | 4 | WASHER, LOCK, 1/2″, MFD front fenders |
| 14 | 425-108 | 4 | NUT, 1/2″-13, G5, MFD front fenders |
| 16 | 1340664C1 | 2 | FENDER, front wheel, MFD tractor |
| 17 | 1340559C2 | 8 | WASHER, square hole, 2-1/2 inch, MFD front fenders |
| 20 | 1340640C1 | 8 | BOLT, carriage, 5/16 NC x 1-1/4 inch, MFD front fenders |
| 21 | 495-21038 | 8 | WASHER, 5/16″, flat, 3/8 x 7/8 x 3/32 inch, MFD front fenders |
| 22 | 425-105 | 8 | NUT, 5/16″-18, G5, MFD front fenders |
| 23 | 122212A1 | 2 | FENDER, front wheel, MFD tractor with wide tires (18.4 – 26R2 or 18.4-28R1) |
| 24 | 1340640C1 | 12 | BOLT, carriage, 5/16 NC x 1-1/4 inch, MFD wide front fenders |
| 25 | 1340559C2 | 12 | WASHER, square hole, 2-1/2 inch, MFD wide front fenders |
| 26 | 495-21038 | 12 | WASHER, 5/16″, flat, 3/8 x 7/8 x 3/32 inch, MFD wide front fenders |
| 27 | 425-105 | 12 | NUT, 5/16″-18, G5, MFD wide front fenders |
| 28 | 136309A1 | 2 | SUPPORT, fender, inner, wide, not shown, front, MFD |
| 1 | 96925C2 | 1 | SUPPORT ASSY., instrument panel |
| 2 | 1974661C1 | 2 | ANGLE, BRACKET – mounting |
| 3 | 1977582C2 | 1 | HOUSING, upper instrument |
| 5 | 104035C1 | 3 | FASTENER, NUT – spacer, No. 10 – 16 |
| 7 | 96696C1 | 1 | SUPPORT ASSY., return spring |
| 9 | 892-11008 | 1 | WASHER, LOCK, M8 |
| 14 | 96931C2 | 1 | BRACKET, brake pedal stop |
| 15 | 614-10025 | 2 | BOLT, Hex, M10 x 25, 8.8, Full Thd |
| 16 | 892-11010 | 1 | WASHER, LOCK, M10 |
| 18 | 96738C3 | 1 | COVER ASSY, instrument panel |
| 19 | 495-81286 | 2 | WASHER, .281″ x 1 1/8″ x .060″, flat, 9/32 x 1-1/8 x 1/16 inch |
| 20 | 614-6016 | 2 | BOLT, Hex, M6 x 16, 8.8 |
| 26 | 1343812C1 | 1 | SYMBOLS, EMBLEM – Magnum |
| 27 | 103957C1 | 6 | NUT, speed, No. 10 – 16 |
| 28 | 104036C1 | 2 | NUT, cover to instrument panel |
| 29 | 122856A1 | 1 | SUPPORT, BRACKET – switch mounting |
| 30 | 96739C2 | 1 | COVER ASSY, side, right, with shutdown override description, no longer available, order 96739C3 |
| 30 | 96739C3 | 1 | COVER ASSY, side, right, without shutdown override description |
| 31 | 96740C2 | 1 | COVER ASSY, side, left |
| 32 | 614-10020 | 4 | BOLT, Hex, M10 x 20, 8.8, Full Thd |
| 33 | 825-1410 | 4 | NUT, M10, Cl 8 |
| 35 | 614-8016 | 1 | BOLT, Hex, M8 x 16, 8.8, left-hand |
| 36 | 825-1408 | 2 | NUT, M8, Cl 8 |
| 37 | 1270762C1 | 2 | SCREW, SELF TAPPING, pan head Phillips, self-tapping, No. 10-16 x 3/4 inch, mounts cover to |
| 38 | 1964796C1 | 1 | BLANK-OFF PLUG, cover, used without horn |
| 1 | 1977661C1 | 1 | PAD, upper instrument housing |
| 2 | 1977660C2 | 1 | PAD, front console |
| 3 | 1977659C2 | 1 | PAD, front console lower |
| 4 | 1977663C1 | 1 | PAD, instrument side panel, left |
| 5 | 1977662C1 | 1 | PAD, instrument side panel, right |
| 6 | 1977738C1 | 1 | SUPPORT, BRACKET – console cover |
| 7 | 1977737C1 | 1 | COVER ASSY, console pad lower |
| 8 | 96900C1 | 1 | NUT, U, #10-16, Panel type |
| 9 | 1975919C1 | 1 | SCREW, special, No. 10 – 16 x 1 inch (Black) |
| 9 | 1990951C1 | 2 | SCREW, Phillips washer, No. 10 – 16 x 5/8 inch (Gray) |
| 10 | 1977865C1 | 2 | CLIP, christmas tree |
| 1 | 96996C3 | 1 | COVER ASSY, transmission and hitch control, includes items 1B – 1D, prior to tractor P.I.N. |
| 2 | 96730C3 | 1 | DOOR, hitch operation |
| 3 | 1344244C1 | 1 | TRAY, utility |
| 4 | 96724C3 | 1 | COVER, remote |
| 5 | 96899C1 | 1 | BRACKET, cover support |
| 10 | 490-1108 | 10 | SCREW, Cross Pan Hd, #10-32 x 1/2″, machine, pan Phillips, No. 10 NF x 1/2 inch |
| 11 | 495-31022 | 10 | WASHER, #10 |
| 12 | 97006C1 | 2 | BOLT, BOLT – hex flange, special, 6 – 1 x 20 mm, polyseal |
| 16 | 97000C1 | 1 | ASH TRAY, receiver |
| 17 | 97042C1 | 1 | GASKET, ash tray |
| 18 | 96723C2 | 1 | PANEL ASSY., corner |
| 19 | 495-11053 | 2 | WASHER, 1/2″, SAE, (17/32″ x 1-1/16″ x 3/32″) |
| 20 | 1958720C1 | 2 | STUD, panel retaining |
| 22 | 96956C2 | 1 | BUTTON, KNOB – cover panel retaining |
| 23 | 1971363C1 | 1 | RETAINER, bolt |
| 24 | 123399A1 | 1 | PANEL, right-hand side console, includes pad |
| 26 | 1990565C1 | 1 | PANEL ASSY., operator manual |
| 29 | 1981941C3 | 1 | PLATE, LARGE, shift selector, 4-speed reverse, without creeper |
| 30 | 1981942C4 | 1 | PLATE, LARGE, shift selector, 4-speed reverse, with creeper |
| 33 | 96578C4 | 1 | ROD, rest, shift selector |
| 34 | 614-6016 | 6 | BOLT, Hex, M6 x 16, 8.8 |
| 35 | 614-6012 | 4 | BOLT, Hex, M6 x 12, 8.8 |
| 36 | 1974696C1 | 1 | BRACKET, console support |
| 37 | 495-11034 | 2 | WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch |
| 38 | 829-1408 | 1 | NUT, M8, Cl 10 |
| 40 | 490-11010 | 1 | SCREW, Cross Pan Hd, #10-32 x 5/8″, machine, pan Phillips, No. 10 NF x 5/8 inch |
| 1 | 96886C5 | 1 | LEVER, switch, creeper |
| 2 | 97063C1 | 1 | WASHER, curved |
| 3 | 738-1214 | 1 | PIN, LOCK, M2 x 14, Slotted, roll, 2 x 14 mm, replaces 30786R1 pin |
| 4 | 97062C1 | 1 | CABLE PULLING GRIP, creeper switch |
| 5 | 96569C7 | 1 | SUPPORT ASSY., shift and governor control |
| 6 | 96725C1 | 1 | PANEL ASSY., front cover |
| 14 | 97297C1 | 1 | ROD, tower support |
| 15 | 825-1406 | 2 | NUT, M6, Cl 8, May be replaced by 825-5146 serrated flange nut, item 15A |
| 17 | 96890C2 | 1 | BRACKET, creeper switch, replaces 96890C1 bracket |
| 18 | 840-1516 | 2 | SCREW, Cross Pan Hd, M5 x 16, Replaces 30479R1 bolt |
| 19 | 895-11005 | 2 | WASHER, M5 x 10 x 1 |
| 20 | 892-11005 | 2 | WASHER, LOCK, M5 |
| 21 | 824-1405 | 2 | NUT, M5, Cl 5 |
| 25 | 614-10035 | 2 | BOLT, Hex, M10 x 35, 8.8, Full Thd |
| 26 | 825-2406 | 4 | NUT, M6 x 1, Flg, Cl 8 |
| 27 | 96700C2 | 1 | BRACKET, control support |
| 28 | 614-8025 | 2 | BOLT, Hex, M8 x 25, 8.8 |
| 29 | 495-11034 | 4 | WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch |
| 30 | 832-41308 | 2 | NUT, M8 x 1.25, Cl 10, hex, self-locking, 8 mm – 1.25, class 10.9 |
| 33 | 1340412C2 | 1 | SUPPORT, BRACKET – shift cable, upper |
| 34 | 628-8030 | 2 | BOLT, Hex, M8 x 30, 10.9, Full Thd |
| 35 | 832-41308 | 2 | NUT, M8 x 1.25, Cl 10, hex, self-locking, 8 mm – 1.25, class 10.9 |
| 36 | 96561C6 | 1 | SUPPORT, shift controls |
| 1 | 134181A1 | 1 | SEAT, KIT – seat cushion and backrest, complete |
| 2 | 132886A1 | 1 | BACKREST, KIT – cloth, with structure |
| 10 | 1974703C2 | 1 | ARMREST ASSY., KIT – seat, right-hand, black, includes (1) drive pin, no longer available, order |
| 11 | 1981818C1 | 1 | ARMREST, KIT – left-hand, black |
| 13 | 38-31016 | 2 | PIN, 5/32″ x 1″, Coiled |
| 19 | 1343982C1 | 1 | BELT, SAFETY, seat |
| 21 | 328-724 | 1 | BOLT, Hex, 7/16″-20 x 1 1/2″, G8 |
| 22 | 328-732 | 1 | BOLT, Hex, 7/16″-20 x 2″, G8 |
| 23 | 413-544 | 2 | BOLT, Hex, 5/16″-18 x 2 3/4″, G5 |
| 25 | 395-11053 | 2 | WASHER, 1/2″, flat, 17/32 x 1-1/16 x 3/32 inch |
| 26 | 232-4117 | 2 | NUT, LOCK, 7/16″-14, GC |
| 1 | 134180A1 | 1 | PLATE, seat adapter |
| 2 | 413-524 | 4 | BOLT, Hex, 5/16″-18 x 1 1/2″, G5, hex, 5/16 NC x 1-1/2 inch |
| 3 | 134144A1 | 4 | SPACER, plate |
| 7 | 417-512 | 4 | BOLT, Sq Hd, 5/16″-18 x 3/4″, G2, BOLT – square head, 5/16 NC x 3/4 inch, grade 2 |
| 8 | 413-512 | 4 | BOLT, Hex, 5/16″-18 x 3/4″, G5, Full Thd, hex, 5/16 NC x 3/4 inch |
| 9 | 495-11034 | 4 | WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch |
| 10 | 230-4225 | 8 | NUT, LOCK, 5/16″-18, GA, hex, self-locking, 5/16 inch NC |
| 12 | 133422A1 | 2 | BUMPER, down stop |
| 14 | 1981849C2 | 2 | SHOCK ABSORBER, BUMPER – rubber, upper housing |
| 15 | 231-1444 | 2 | NUT, LOCK, 1/4″-20, GB |
| 1 | 1990642C1 | 1 | HOUSING, upper suspension |
| 2 | 1990645C1 | 1 | LATCH, ASSEMBLY – isolator, fore and aft, component parts not serviced separately, see fig. 9-62 for |
| 3 | 276-24812 | 2 | SCREW, SELF TAPPING, Hex Hd, 5/16″ x 3/4″ |
| 4 | 1990643C1 | 1 | FRAME ASSY, ARM – scissor, suspension |
| 5 | A49529 | 1 | SHAFT, bushing tube |
| 6 | 230-4216 | 1 | NUT, LOCK, 3/8″-16, GA |
| 7 | 1981834C1 | 1 | HOUSING, lower |
| 8 | 443-13812 | 1 | SCREW, Cross Flat Hd, 3/8″-16 x 3/4″, machine, flat Phillips, 3/8 NC x 3/4 inch |
| 9 | 1981842C1 | 1 | SPRING, air, no longer available, order 197793A1 kit on fig. 9-68 |
| 10 | 413-68 | 1 | BOLT, Hex, 3/8″-16 x 1/2″, G5, Full Thd |
| 11 | 131-425 | 1 | NUT, LOCK, Push, 1/2″, push-on type, 1/2 inch |
| 13 | 134237A2 | 1 | HARNESS, compressor wire, replaces 134237A1 harness |
| 15 | 440-1086 | 2 | SCREW, Cross Pan Hd, #8-32 x 3/8″, machine, pan Phillips, No. 8 NC x 3/8 inch |
| 16 | 495-31022 | 2 | WASHER, #10 |
| 17 | L18337 | 2 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch |
| 18 | 134456A1 | 1 | HARNESS, wire adapter, with grommet |
| 19 | 1981849C2 | 2 | SHOCK ABSORBER, BUMPER – rubber, upper housing, not shown, see item 14 on fig. 9-56 for |
| 33 | A45519 | 1 | WASHER, flat, plastic, special, 33/64 x 1-1/8 x 1/16 inch |
| 34 | 131-425 | 1 | NUT, LOCK, Push, 1/2″, push-on type, 1/2 inch |
| 37 | 434-48 | 2 | BOLT, CARRIAGE, Short NK, 1/4″-20 x 1/2″, G5, Full Thd |
| 38 | 231-1444 | 2 | NUT, LOCK, 1/4″-20, GB |
| 39 | 495-11041 | 1 | WASHER, 3/8″, SAE, Flat, (13/32 x 13/16 x 1/16″) |
| 42 | 230-4715 | 1 | NUT, LOCK, 5/16″-24, GA, Hex |
| 43 | A49679 | 2 | BUSHING, rubber |
| 45 | 1981845C1 | 1 | ANGLE, mounting, shock mounting |
| 48 | 493-11065 | 1 | WASHER, LOCK, Ext-Int Tooth, 5/8″, internal-external tooth lock, 5/8 inch |
| 49 | 1987186C2 | 1 | KNOB, KNOB – switch, air suspension, replaces 1987186C1 knob |
| 55 | L18337 | 4 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch |
| 61 | A45519 | 1 | WASHER, flat, plastic, special, 33/64 x 1-1/8 x 1/16 inch |
| 63 | 1343833C1 | 1 | TUBE, GUARD – corrugated, 3/8 ID x 24 inch long, cut from 179026A1 |
| 64 | L18337 | 2 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch |
| 66 | 135536A1 | 1 | TUBE, PLASTIC-RUBBER, SLEEVE – guard, 419 mm (16-1/2 inch) long, cut from 179026A1 |
| 67 | 133422A1 | 2 | BUMPER, down stop, not shown, see item 12 on fig. 9-56 |
| 19 | 495-11034 | 4 | WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch |
| 20 | 614-8020 | 4 | BOLT, Hex, M8 x 20, 8.8 |
| 21 | 1977735C1 | 2 | SUPPORT, BRACKET – mounting, seat |
| 22 | 1954650C1 | 4 | STUD, 8 x 80 mm |
| 23 | F15988 | 4 | SPACER, seat mounting |
| 24 | 892-11008 | 4 | WASHER, LOCK, M8 |
| 25 | 829-1408 | 4 | NUT, M8, Cl 10 |
| 1 | 134181A2 | 1 | PACKAGE, KIT – seat top, without armrest, cushion and backrest, complete |
| 2 | 132886A1 | 1 | BACKREST, KIT – cloth, with structure |
| 9 | 1999693C1 | 1 | KIT, CLIP – christmas tree, package of 14, retaining, plastic |
| 10 | 143199A1 | 1 | ARMREST, right-hand, black, includes armrest and switch cover plug |
| 11 | 1981818C1 | 1 | ARMREST, KIT – armrest, left-hand, black |
| 13 | 38-31016 | 2 | PIN, 5/32″ x 1″, Coiled |
| 14 | 1974711C1 | 1 | LEVER, KNOB – backrest tilt |
| 19 | 1343982C1 | 1 | BELT, SAFETY, seat |
| 20 | 1975957C1 | 1 | BRACKET, seat belt, left-hand |
| 21 | 328-724 | 1 | BOLT, Hex, 7/16″-20 x 1 1/2″, G8 |
| 22 | 328-732 | 1 | BOLT, Hex, 7/16″-20 x 2″, G8 |
| 23 | 413-544 | 2 | BOLT, Hex, 5/16″-18 x 2 3/4″, G5 |
| 24 | 1343875C1 | 2 | SPACER, 25/64 ID x 1/2 inch |
| 25 | 496-81010 | 3 | WASHER, flat, 15/32 x 1 x 7/64 inch, hardened |
| 26 | 232-4617 | 1 | NUT, LOCK, 7/16″-20, GC |
| 27 | 176091A1 | 1 | PACKAGE,SERVICE, KIT – retaining, hog ring, package of 48 rings for cushions, package of 50 rings |
| 28 | 141566A1 | 1 | PLATE, LARGE, reinforcement |
| 1 | 134180A1 | 1 | PLATE, seat adapter |
| 2 | 413-524 | 4 | BOLT, Hex, 5/16″-18 x 1 1/2″, G5, hex, 5/16 NC x 1-1/2 inch |
| 3 | 134144A1 | 4 | SPACER, plate |
| 7 | 417-512 | 4 | BOLT, Sq Hd, 5/16″-18 x 3/4″, G2, BOLT – square head, 5/16 NC x 3/4 inch, grade 2 |
| 8 | 413-512 | 4 | BOLT, Hex, 5/16″-18 x 3/4″, G5, Full Thd, hex, 5/16 NC x 3/4 inch |
| 9 | 495-11034 | 4 | WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch |
| 10 | 231-4115 | 8 | NUT, LOCK, 5/16″-18, GB |
| 12 | 133422A1 | 2 | BUMPER, down stop |
| 14 | 340-12520 | 2 | SCREW, Cross Pan Hd, 1/4″-20 x 1 1/4″ |
| 16 | 231-1444 | 2 | NUT, LOCK, 1/4″-20, GB |
| 1 | 241189A1 | 1 | HOUSING, upper, suspension, replaces 1990642C1 housing |
| 2 | 1990645C1 | 1 | LATCH, ASSEMBLY – isolator, fore and aft, component parts not serviced separately, see fig. 9-72 for |
| 3 | 276-24812 | 2 | SCREW, SELF TAPPING, Hex Hd, 5/16″ x 3/4″ |
| 4 | 1990643C1 | 1 | FRAME ASSY, ARM – scissor, suspension |
| 5 | A49529 | 1 | SHAFT, bushing tube |
| 6 | 230-4216 | 1 | NUT, LOCK, 3/8″-16, GA |
| 7 | 226560A1 | 1 | HOUSING, lower, replaces 1981834C1 housing |
| 8 | 443-13812 | 1 | SCREW, Cross Flat Hd, 3/8″-16 x 3/4″, machine, flat Phillips, 3/8 NC x 3/4 inch |
| 10 | 413-68 | 1 | BOLT, Hex, 3/8″-16 x 1/2″, G5, Full Thd |
| 11 | 131-425 | 1 | NUT, LOCK, Push, 1/2″, push-on type, 1/2 inch |
| 13 | 134237A2 | 1 | HARNESS, compressor wire |
| 15 | 440-1086 | 2 | SCREW, Cross Pan Hd, #8-32 x 3/8″, machine, pan Phillips, No. 8 NC x 3/8 inch |
| 16 | 495-31022 | 2 | WASHER, #10 |
| 17 | L18337 | 2 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch |
| 18 | 134456A1 | 1 | HARNESS, wire adapter, with grommet |
| 19 | 1981849C2 | 2 | SHOCK ABSORBER, BUMPER – rubber, upper housing, not shown, see item 15 on fig. 9-66 for |
| 33 | A45519 | 1 | WASHER, flat, plastic, special, 33/64 x 1-1/8 x 1/16 inch |
| 34 | 131-425 | 1 | NUT, LOCK, Push, 1/2″, push-on type, 1/2 inch |
| 37 | 434-48 | 2 | BOLT, CARRIAGE, Short NK, 1/4″-20 x 1/2″, G5, Full Thd |
| 38 | 231-1444 | 2 | NUT, LOCK, 1/4″-20, GB |
| 39 | 495-11041 | 2 | WASHER, 3/8″, SAE, Flat, (13/32 x 13/16 x 1/16″) |
| 42 | 230-4715 | 1 | NUT, LOCK, 5/16″-24, GA, Hex |
| 43 | A49679 | 2 | BUSHING, rubber |
| 45 | 1981845C1 | 1 | ANGLE, mounting, shock mounting |
| 48 | 493-11065 | 1 | WASHER, LOCK, Ext-Int Tooth, 5/8″, internal-external tooth lock, 5/8 inch |
| 49 | 1987186C2 | 1 | KNOB, KNOB – switch, air suspension, replaces 1987186C1 knob |
| 55 | L18337 | 4 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch |
| 61 | A45519 | 1 | WASHER, flat, plastic, special, 33/64 x 1-1/8 x 1/16 inch |
| 63 | 179026A1 | 1 | TUBE, PLASTIC-RUBBER, SLEEVE – guard, 10 (3/8) ID x 615 mm (24-1/4 inch) long |
| 64 | L18337 | 2 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch |
| 66 | 179026A1 | 1 | TUBE, PLASTIC-RUBBER, SLEEVE – guard, 10 (3/8) ID x 615 mm (24-1/4 inch) long |
| 67 | 133422A1 | 2 | BUMPER, down stop, not shown, see item 12 on fig. 9-66 for bumper |
| 19 | 495-11034 | 4 | WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch |
| 20 | 614-8020 | 4 | BOLT, Hex, M8 x 20, 8.8 |
| 21 | 1977735C1 | 2 | SUPPORT, BRACKET – mounting, seat |
| 22 | 1954650C1 | 4 | STUD, 8 x 80 mm |
| 23 | F15988 | 4 | SPACER, seat mounting |
| 24 | 892-11008 | 4 | WASHER, LOCK, M8 |
| 25 | 829-1408 | 4 | NUT, M8, Cl 10 |
| 1 | 134128A2 | 1 | SEAT, KIT – seat cushion and backrest, complete, replaces 134128A1 kit |
| 2 | 132886A1 | 1 | BACKREST, KIT – cloth, with structure |
| 9 | 103-1131 | 10 | RING, SNAP, #31, Ext |
| 11 | 132880A1 | 1 | ARMREST, right-hand, black, includes (1) drive pin, no longer available, order 143199A1 armrest on |
| 12 | 132882A1 | 1 | ARMREST, left-hand, black |
| 13 | 132883A1 | 1 | SET OF PARTS, KIT – left-hand armrest adjustment |
| 14 | 413-528 | 1 | BOLT, Hex, 5/16″-18 x 1 3/4″, G5, hex, 5/16 NC x 1-3/4 inch |
| 15 | 495-11034 | 1 | WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch |
| 16 | 413-544 | 2 | BOLT, Hex, 5/16″-18 x 2 3/4″, G5 |
| 17 | 1343875C1 | 2 | SPACER, 25/64 ID x 1/2 inch |
| 19 | 38-31016 | 2 | PIN, 5/32″ x 1″, Coiled |
| 25 | 1343982C1 | 1 | BELT, SAFETY, seat |
| 27 | 328-724 | 1 | BOLT, Hex, 7/16″-20 x 1 1/2″, G8 |
| 28 | 328-732 | 1 | BOLT, Hex, 7/16″-20 x 2″, G8 |
| 29 | 413-544 | 2 | BOLT, Hex, 5/16″-18 x 2 3/4″, G5 |
| 31 | 395-11053 | 2 | WASHER, 1/2″, flat, 17/32 x 1-1/16 x 3/32 inch |
| 32 | 232-4117 | 2 | NUT, LOCK, 7/16″-14, GC |
| 33 | 132868A1 | 1 | SET OF PARTS, KIT – height adjustment, includes (3) cover plate, (1) rocker switch, and (4) screws |
| 3 | 117-109 | 4 | BOLT, Sq Hd, 5/18″-16 x 3/4″, G5 |
| 4 | 413-520 | 4 | BOLT, Hex, 5/16″-18 x 1 1/4″, G5, hex, 5/16 NC x 1-1/4 inch |
| 5 | 230-4215 | 8 | NUT, LOCK, 5/16″-18, GA |
| 6 | 135513A1 | 1 | SPRING, torsion, left-hand |
| 7 | 135514A1 | 1 | SPRING, torsion, right-hand |
| 10 | 100-3325 | 2 | RING, LOCKING, #25, .207″ Dia, E-Type, If used |
| 11 | 134144A1 | 8 | SPACER, plate |
| 12 | 134146A1 | 1 | LEVER, CONTROL, slide control |
| 14 | 413-816 | 1 | BOLT, Hex, 1/2″-13 x 1″, G5, Full Thd |
| 27 | L18337 | 3 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch, cable |
| 31 | L18337 | 3 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch, cable |
| 37 | 134148A1 | 1 | SUPPORT, SEAT, PLATE – swivel, complete, includes items 48-50 |
| 38 | 132878A2 | 1 | ISOLATOR, PLATE – lateral isolator, complete, includes items 13-21, replaces 132878A1 plate |
| 39 | 413-532 | 4 | BOLT, Hex, 5/16″-18 x 2″, G5 |
| 40 | 413-510 | 4 | BOLT, Hex, 5/16″-18 x 5/8″, G5, Full Thd |
| 41 | 231-4115 | 4 | NUT, LOCK, 5/16″-18, GB |
| 42 | 495-11034 | 2 | WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch |
| 46 | 135510A1 | 1 | ROD, ADJUSTMENT, isolator, includes knob |
| 47 | 38-31012 | 2 | PIN, 5/32″ x 3/4″, Coiled, 5/32″ x 3/4″, Coiled |
| 48 | 135511A1 | 1 | ROD, ADJUSTMENT, swivel, includes knob |
| 49 | A47375 | 1 | SPRING, detent |
| 52 | 433-512 | 4 | BOLT, CARRIAGE, Short NK, 5/16″-18 x 3/4″, G5, 5/16 NC x 3/4 inch |
| 53 | 231-4115 | 4 | NUT, LOCK, 5/16″-18, GB |
| 54 | 1344025C1 | 1 | PIN, LARGE, clevis, shock absorber |
| 55 | 100-3350 | 1 | RING, LOCKING, #50, .392″ Dia, E-Type, (Replaces A27804) |
| 1 | 1990642C1 | 1 | HOUSING, upper, suspension |
| 2 | 132862A1 | 1 | DIPPER, ARM – suspension |
| 3 | A49529 | 1 | SHAFT, bushing tube |
| 4 | 230-4216 | 1 | NUT, LOCK, 3/8″-16, GA |
| 5 | 1981834C1 | 1 | HOUSING, lower |
| 6 | 443-13812 | 1 | SCREW, Cross Flat Hd, 3/8″-16 x 3/4″, machine, flat Phillips, 3/8 NC x 3/4 inch |
| 7 | 1981842C1 | 1 | SPRING, air, no longer available, order 197793A1 kit on fig. 9-94 |
| 8 | 413-68 | 1 | BOLT, Hex, 3/8″-16 x 1/2″, G5, Full Thd |
| 9 | 131-425 | 1 | NUT, LOCK, Push, 1/2″, push-on type, 1/2 inch |
| 13 | 495-11041 | 2 | WASHER, 3/8″, SAE, Flat, (13/32 x 13/16 x 1/16″) |
| 14 | 132867A1 | 1 | HARNESS, wire |
| 26 | 131-425 | 1 | NUT, LOCK, Push, 1/2″, push-on type, 1/2 inch |
| 28 | 138-317 | 1 | PIN, LOCK, 1/8″ x 5/8″, Slotted |
| 30 | 134145A1 | 1 | BOLT, BRACKET – cable control, no longer available, order 144514A1 bracket on fig.9-94 |
| 32 | A45519 | 1 | WASHER, flat, plastic, special, 33/64 x 1-1/8 x 1/16 inch |
| 34 | 434-48 | 2 | BOLT, CARRIAGE, Short NK, 1/4″-20 x 1/2″, G5, Full Thd |
| 35 | 231-1444 | 2 | NUT, LOCK, 1/4″-20, GB |
| 36 | 495-11041 | 1 | WASHER, 3/8″, SAE, Flat, (13/32 x 13/16 x 1/16″) |
| 37 | A49678 | 1 | WASHER, flat, 21/64 x 1 x 5/64 inch |
| 39 | 230-4715 | 1 | NUT, LOCK, 5/16″-24, GA, Hex |
| 40 | A49679 | 2 | BUSHING, rubber |
| 42 | 1981845C1 | 1 | ANGLE, mounting, shock mounting |
| 45 | L18337 | 2 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch |
| 47 | 135536A1 | 1 | TUBE, PLASTIC-RUBBER, SLEEVE – guard, 419 mm (16-1/2 inch) long, cut from 179026A1 sleeve |
| 48 | L18337 | 3 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch |
| 49 | 230-4715 | 1 | NUT, LOCK, 5/16″-24, GA, Hex |
| 5 | 276-24812 | 2 | SCREW, SELF TAPPING, Hex Hd, 5/16″ x 3/4″ |
| 6 | 132863A1 | 1 | ISOLATOR, LATCH – isolator, fore and aft, component parts not serviced separately |
| 8 | 133422A1 | 2 | BUMPER, down stop |
| 10 | 1981849C2 | 2 | SHOCK ABSORBER, BUMPER – rubber, upper housing |
| 11 | 231-1444 | 2 | NUT, LOCK, 1/4″-20, GB |
| 12 | 134147A1 | 2 | SUPPORT, BRACKET – mounting, seat, 1-3/4 inch high riser, no longer used on deluxe seats, order |
| 12 | 144847A1 | 2 | RISER, BRACKET – mounting, seat, 3-1/4 inch high riser |
| 13 | 495-11034 | 4 | WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch |
| 14 | 614-8020 | 4 | BOLT, Hex, M8 x 20, 8.8 |
| 15 | 1954650C1 | 4 | STUD, 8 x 80 mm |
| 16 | F15988 | 4 | SPACER, seat mounting |
| 17 | 892-11008 | 4 | WASHER, LOCK, M8 |
| 18 | 829-1408 | 4 | NUT, M8, Cl 10 |
| 1 | 134181A2 | 1 | PACKAGE, KIT – seat top, without armrest, includes seat cushion and backrest, complete |
| 2 | 132886A1 | 1 | BACKREST, KIT – cloth, complete structure with lumbar shaft assembly and knob, without armrest |
| 9 | 1999693C1 | 1 | KIT, CLIP – christmas tree, package of 14, retaining, plastic |
| 11 | 143199A1 | 1 | ARMREST, right-hand, black, includes switch cover plug |
| 12 | 132882A1 | 1 | ARMREST, left-hand, pad only, black |
| 13 | 132883A1 | 1 | SET OF PARTS, KIT – left-hand armrest adjustment, includes thumb wheel, cable, hub latch, bolt, nut |
| 14 | 413-528 | 1 | BOLT, Hex, 5/16″-18 x 1 3/4″, G5, hex, 5/16 NC x 1-3/4 inch |
| 15 | 495-11034 | 1 | WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch |
| 16 | 413-544 | 2 | BOLT, Hex, 5/16″-18 x 2 3/4″, G5 |
| 17 | 1343875C1 | 2 | SPACER, 25/64 ID x 1/2 inch |
| 19 | 38-31016 | 2 | PIN, 5/32″ x 1″, Coiled |
| 20 | 1974711C1 | 1 | LEVER, KNOB – backrest tilt |
| 25 | 1343982C1 | 1 | BELT, SAFETY, seat |
| 26 | 1975957C1 | 1 | BRACKET, seat belt, left-hand |
| 27 | 328-724 | 1 | BOLT, Hex, 7/16″-20 x 1 1/2″, G8 |
| 28 | 328-732 | 1 | BOLT, Hex, 7/16″-20 x 2″, G8 |
| 29 | 413-544 | 2 | BOLT, Hex, 5/16″-18 x 2 3/4″, G5 |
| 30 | 1343875C1 | 2 | SPACER, 25/64 ID x 1/2 inch |
| 31 | 496-81010 | 3 | WASHER, flat, 15/32 x 1 x 7/64 inch, hardened |
| 32 | 232-4617 | 1 | NUT, LOCK, 7/16″-20, GC |
| 33 | 132868A1 | 1 | SET OF PARTS, KIT – height adjustment, includes (3) cover plate, (1) rocker switch, and (4) screws |
| 34 | 141566A1 | 1 | PLATE, LARGE, reinforcement |
| 35 | 176091A1 | 1 | PACKAGE,SERVICE, KIT – retaining, hog ring, package of 48 rings for cushions |
| 1 | 134148A1 | 1 | SUPPORT, SEAT, PLATE – swivel, complete |
| 2 | 135511A1 | 1 | ROD, ADJUSTMENT, swivel, includes knob |
| 3 | A47375 | 1 | SPRING, detent |
| 5 | 132878A3 | 1 | ISOLATOR, PLATE – lateral, complete |
| 8 | 253593A1 | 2 | BEARING, isolator rod |
| 9 | 135510A2 | 1 | ROD, ADJUSTMENT, isolator, includes knob |
| 10 | 38-31012 | 2 | PIN, 5/32″ x 3/4″, Coiled, 5/32″ x 3/4″, Coiled |
| 11 | 1344026C1 | 1 | SPRING, latch |
| 13 | 495-11041 | 2 | WASHER, 3/8″, SAE, Flat, (13/32 x 13/16 x 1/16″) |
| 15 | 230-4715 | 1 | NUT, LOCK, 5/16″-24, GA, Hex |
| 18 | 1344025C1 | 1 | PIN, LARGE, clevis, shock mount |
| 19 | 100-3350 | 1 | RING, LOCKING, #50, .392″ Dia, E-Type |
| 20 | 433-512 | 4 | BOLT, CARRIAGE, Short NK, 5/16″-18 x 3/4″, G5, 5/16 NC x 3/4 inch |
| 21 | 230-4215 | 4 | NUT, LOCK, 5/16″-18, GA |
| 23 | 413-816 | 1 | BOLT, Hex, 1/2″-13 x 1″, G5, Full Thd |
| 28 | 180587A1 | 1 | HANDLE, KNOB – slide control, fore/aft |
| 35 | L18337 | 3 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch |
| 37 | 231-1444 | 2 | NUT, LOCK, 1/4″-20, GB |
| 42 | L18337 | 3 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch |
| 45 | 413-532 | 4 | BOLT, Hex, 5/16″-18 x 2″, G5 |
| 46 | 187006A1 | 2 | CUP, SPACER – cupped |
| 47 | 700711545 | 2 | CUP, SPACER – cupped |
| 48 | 413-510 | 4 | BOLT, Hex, 5/16″-18 x 5/8″, G5, Full Thd |
| 49 | 495-11034 | 2 | WASHER, 5/16″, SAE, flat 11/32 x 11/16 x 1/16 inch |
| 50 | 231-4115 | 4 | NUT, LOCK, 5/16″-18, GB |
| 51 | 135513A1 | 1 | SPRING, torsion |
| 52 | 135514A1 | 1 | SPRING, torsion |
| 55 | 100-3325 | 2 | RING, LOCKING, #25, .207″ Dia, E-Type |
| 56 | 131-413 | 2 | NUT, LOCK, Rd Flat Push, 1/4″ x 17/32″, push-on type, 1/4 x 17/32 inch |
| 57 | 134146A1 | 1 | LEVER, CONTROL, slide |
| 58 | 134144A1 | 4 | SPACER, plate |
| 61 | 117-109 | 4 | BOLT, Sq Hd, 5/18″-16 x 3/4″, G5 |
| 62 | 413-520 | 4 | BOLT, Hex, 5/16″-18 x 1 1/4″, G5, hex, 5/16 NC x 1-1/4 inch |
| 63 | 230-4215 | 8 | NUT, LOCK, 5/16″-18, GA |
| 1 | 241189A1 | 1 | HOUSING, upper, suspension, replaces 1990642C1 housing |
| 2 | 132862A1 | 1 | DIPPER, ARM – suspension |
| 3 | A49529 | 1 | SHAFT, bushing tube |
| 4 | 230-4216 | 1 | NUT, LOCK, 3/8″-16, GA |
| 5 | 226560A1 | 1 | HOUSING, lower |
| 6 | 443-13812 | 1 | SCREW, Cross Flat Hd, 3/8″-16 x 3/4″, machine, flat Phillips, 3/8 NC x 3/4 inch |
| 8 | 413-68 | 1 | BOLT, Hex, 3/8″-16 x 1/2″, G5, Full Thd |
| 9 | 131-425 | 3 | NUT, LOCK, Push, 1/2″, push-on type, 1/2 inch |
| 13 | 495-11041 | 4 | WASHER, 3/8″, SAE, Flat, (13/32 x 13/16 x 1/16″) |
| 14 | 132867A1 | 1 | HARNESS, wire |
| 15 | A47760 | 2 | BUSHING, TUBE – bearing, shaft |
| 26 | 131-425 | 1 | NUT, LOCK, Push, 1/2″, push-on type, 1/2 inch |
| 28 | 138-317 | 1 | PIN, LOCK, 1/8″ x 5/8″, Slotted |
| 30 | 144514A1 | 1 | SUPPORT, BRACKET – cable control, shock |
| 34 | 434-48 | 2 | BOLT, CARRIAGE, Short NK, 1/4″-20 x 1/2″, G5, Full Thd |
| 35 | 231-1444 | 2 | NUT, LOCK, 1/4″-20, GB |
| 36 | 495-11041 | 2 | WASHER, 3/8″, SAE, Flat, (13/32 x 13/16 x 1/16″) |
| 39 | 230-4715 | 1 | NUT, LOCK, 5/16″-24, GA, Hex |
| 40 | A49679 | 2 | BUSHING, rubber |
| 42 | 1981845C1 | 1 | ANGLE, mounting, shock mounting |
| 45 | L18337 | 2 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch |
| 47 | 179026A1 | 1 | TUBE, PLASTIC-RUBBER, SLEEVE – guard, 10 (3/8) ID x 615 mm (24-1/4 inch) long |
| 48 | L18337 | 3 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch |
| 49 | 230-4715 | 1 | NUT, LOCK, 5/16″-24, GA, Hex |
| 5 | 276-24812 | 2 | SCREW, SELF TAPPING, Hex Hd, 5/16″ x 3/4″ |
| 6 | 132863A1 | 1 | ISOLATOR, LATCH – fore and aft, component parts not serviced separately |
| 8 | 133422A1 | 2 | BUMPER, down stop |
| 9 | 340-12520 | 2 | SCREW, Cross Pan Hd, 1/4″-20 x 1 1/4″ |
| 11 | 231-1444 | 2 | NUT, LOCK, 1/4″-20, GB |
| 12 | 144847A1 | 2 | RISER, BRACKET – mounting, seat, 3-1/4 inch high riser, prior to seat serial number 1348826 |
| 12 | 222771A1 | 2 | RISER, BRACKET – mounting, seat, 3-7/8 inch high riser, effective seat serial number 1348826 and |
| 13 | 495-11034 | 4 | WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch |
| 14 | 614-8020 | 4 | BOLT, Hex, M8 x 20, 8.8 |
| 15 | 1954650C1 | 4 | STUD, 8 x 80 mm |
| 16 | F15988 | 4 | SPACER, seat mounting |
| 17 | 892-11008 | 4 | WASHER, LOCK, M8 |
| 18 | 829-1408 | 4 | NUT, M8, Cl 10 |
| 20 | 190156A1 | 1 | SHOCK ABSORBER, KIT – block, sheave |
| 21 | 132868A1 | 1 | SET OF PARTS, KIT – height adjustment, not shown, see fig. 9-86, item 33 |
| 1 | 96523C2 | 2 | BRACKET, mounting, front |
| 2 | 628-20050 | 8 | BOLT, Hex, M20 x 50, 10.9, Full Thd |
| 3 | 892-11020 | 8 | WASHER, LOCK, M20, 20 mm |
| 4 | 1982052C2 | 1 | SUPPORT, BRACKET – mounting, left rear |
| 5 | 1982053C2 | 1 | SUPPORT, BRACKET – mounting, right rear |
| 6 | 144212C1 | 8 | WASHER, flat, rear mounting spacer |
| 9 | 628-16045 | 4 | BOLT, Hex, M16 x 45, 10.9, Full Thd |
| 10 | 828-16150 | 4 | BOLT, Hex, M16 x 150, 10.9 |
| 11 | 892-11016 | 8 | WASHER, LOCK, M16 |
| 13 | 1286903C1 | 1 | INSULATOR BLOCK, MOUNT – isolation, bottom, 4 needed to do a complete cab |
| 14 | 1982005C1 | 4 | SPACER, rebound |
| 15 | 1286904C1 | 2 | WASHER, SPACER – 1/8 x 1-15/16 inch, not used this application |
| 16 | 1982004C1 | 4 | SCREW, BOLT – special |
| 17 | 117737C1 | 4 | PLATE, mounting |
| 20 | R52105 | 4 | WASHER, flat, 13/16 x 1-3/4 x 7/32 inch |
| 21 | 425-1012 | 4 | NUT, 3/4″-10, G5 |
| 22 | 495-21081 | 2 | WASHER, 3/4″, flat, 13/16 x 2 x 9/64 inch |
| 1 | 96639C1 | 1 | SUPPORT ASSY., step, intermediate and lower |
| 2 | 97049C3 | 1 | STEP, tractor, top |
| 3 | 97050C3 | 2 | STEP, ladder, intermediate and lower |
| 4 | 1348398C1 | 12 | BOLT, BOLT – hex, 10 x 35 mm, grade 8.8 |
| 5 | 1348399C1 | 14 | NUT, hex serrated flange, 10 – 1.5 mm |
| 1 | 104606A3 | 1 | FRAME, ASSEMBLY – cab, not serviced separately, order cab assembly, not shown |
| 3 | 96964C1 | 1 | PLATE ASSY., floor access |
| 4 | 1971260C1 | 2 | SEAL ASSY., floor access plate |
| 5 | 281-34812 | 10 | SCREW, SELF TAPPING, Hex Hd, 5/16″ x 3/4″, self-tapping, hex washer head, 5/16 NC x 3/4 inch |
| 6 | 96951C1 | 1 | PLATE ASSY., implement cable |
| 7 | 281-14512 | 2 | SCREW, SELF TAPPING, Hex Wash Hd, #10 x 3/4″, self-tapping, hex washer head, No. 10 NC x 3/4 |
| 8 | A165354 | 1 | SEAL, plate |
| 11 | 231-5145 | 1 | NUT, Flg, USR, 5/16″-18 |
| 12 | A177462 | 1 | MIRROR, rear view, includes mounting hardware |
| 13 | 1330064C1 | 2 | NUT, hex flange, self-locking, polyseal, 5/16 inch NC |
| 14 | 96845C1 | 1 | BRACKET, mirror |
| 15 | 1330156C1 | 2 | BOLT, self-locking, hex flange, special, 5/16 NC x 3/4 inch |
| 19 | 97028C1 | 1 | PLUG, post, right |
| 23 | 1334281C3 | 1 | INSULATOR, PAD – firewall, front |
| 24 | 1334282C2 | 1 | INSULATOR, PAD – upper |
| 25 | 1334283C2 | 1 | INSULATOR, PAD – firewall, left |
| 26 | 1334284C2 | 1 | INSULATOR, PAD – firewall, right |
| 27 | 97027C1 | 1 | PAD, firewall |
| 28 | 91963C1 | 1 | STRAP, GROUND |
| 29 | 892-11010 | 1 | WASHER, LOCK, M10 |
| 30 | 829-2410 | 1 | NUT, M10 x 1.5, Flg, Cl 10 |
| 33 | 97246C2 | 1 | HANDLE, rear, models without remote hitch switch, (see item 13, fig. 8-32, for handle on models with |
| 34 | 434-516 | 2 | BOLT, CARRIAGE, Short NK, 5/16″-18 x 1″, G5, Full Thd |
| 35 | 495-11034 | 4 | WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch |
| 36 | 492-11031 | 4 | WASHER, LOCK, 5/16″ |
| 37 | 425-105 | 4 | NUT, 5/16″-18, G5 |
| 38 | 245175C1 | 1 | SWITCH, dome lamp, with bent blade terminals, if used |
| 40 | 96720C2 | 1 | COVER ASSY, front cab post, left side lower |
| 41 | 1344112C1 | 2 | SCREW, Phillips, self-tapping, polyseal (Black) |
| 41 | 1990953C1 | 2 | SCREW, Phillips washer, No. 10-24 x 1 inch (Gray) |
| 45 | 97010C1 | 2 | BOLT, SPREADER, hex flange, 6 – 1.0 x 12 mm |
| 46 | 353-411 | 2 | PLUG, Dome, 1.000″ hole, Nylon |
| 47 | 231-5145 | 1 | NUT, Flg, USR, 5/16″-18, Used with interior mirror |
| 1 | 97003C2 | 1 | FENDER, tractor, left |
| 2 | 434-516 | 4 | BOLT, CARRIAGE, Short NK, 5/16″-18 x 1″, G5, Full Thd |
| 3 | 1990666C1 | 1 | SUPPORT, fuel filler tube |
| 6 | 1990669C1 | 1 | SUPPORT, fender, lower left |
| 7 | 1990668C1 | 1 | SUPPORT, fender, center left |
| 8 | 1990667C1 | 1 | SUPPORT, fender, upper left |
| 10 | 477-73112 | 4 | BOLT, Slotted Tr Hd, 5/16″-18 x 3/4″, BOLT – serrated slotted truss head, 5/16 NC x 3/4 inch, mounting |
| 11 | 198983A1 | 4 | WASHER, flat, 11/32 x 1-1/8 x 1/16 inch thick, used with item 10 screw |
| 15 | 1283847C1 | 1 | SUPPORT, BRACKET – rear support |
| 16 | 495-21038 | 2 | WASHER, 5/16″, flat, 3/8 x 7/8 x 3/32 inch |
| 17 | 96704C2 | 1 | COVER, post, upper left |
| 18 | 495-31016 | 1 | WASHER, #6, Used with item 22 screw on upper post cover, if used |
| 19 | 1270762C1 | 2 | SCREW, SELF TAPPING, pan head Phillips, self-tapping, No. 10 – 16 x 3/4 inch, panel |
| 20 | 96709C1 | 1 | COVER ASSY, post, lower left |
| 22 | 140670A1 | 2 | SCREW, hex washer, No. 8 x 3/4 inch, if used, may be replaced by 253419A1 screw with washer, item |
| 23 | 495-31016 | 2 | WASHER, #6, If used |
| 25 | 96764C2 | 1 | PANEL ASSY., frame, lower left front |
| 28 | 96763C1 | 1 | PANEL ASSY., step |
| 29 | 1971318C1 | 1 | STEP, THRESHOLD – entrance, tractor |
| 30 | 1971367C2 | 2 | SCREW, SELF TAPPING, Cross Oval Hd, #10-16 x 3/4″, self-tapping, oval head Phillips, No. 10 – 16 x |
| 31 | 96930C1 | 1 | PLATE, PANEL – tail lamp |
| 33 | 253419A1 | 2 | SCREW, Hex Wash Hd, #8-18 x 5/8″, hex washer, No. 8 – 18 x 5/8 inch, special, hi-lo, if used |
| 1 | 97004C2 | 1 | FENDER, right, tractor |
| 2 | 1283847C1 | 1 | SUPPORT, BRACKET – rear support |
| 3 | 434-516 | 4 | BOLT, CARRIAGE, Short NK, 5/16″-18 x 1″, G5, Full Thd |
| 4 | 495-21038 | 2 | WASHER, 5/16″, flat, 3/8 x 7/8 x 3/32 inch |
| 5 | 231-5145 | 6 | NUT, Flg, USR, 5/16″-18 |
| 6 | 1990670C1 | 1 | SUPPORT, fender, lower right |
| 7 | 1990671C1 | 1 | SUPPORT, fender, upper right |
| 8 | 1990672C1 | 1 | SUPPORT, fender, right front |
| 14 | 96702C2 | 1 | PANEL ASSY., side, right |
| 17 | 1348226C1 | 1 | PANEL ASSY., frame, lower right front |
| 18 | 96710C1 | 1 | COVER ASSY, post, lower right |
| 19 | 96703C2 | 1 | COVER, post, upper right |
| 22 | 1975782C1 | 2 | SCREW, SELF TAPPING, Cross Truss Wash Hd, #10 x 5/8″ |
| 23 | 495-31016 | 1 | WASHER, #6, Used with item 25, if used |
| 25 | 140670A1 | 1 | SCREW, hex washer, No. 8 x 3/4 inch, hi-lo, if used, may be replaced by 253419A1 screw with washer |
| 26 | 253419A1 | 1 | SCREW, Hex Wash Hd, #8-18 x 5/8″, hex washer, No. 8 – 18 x 5/8 inch, special, hi-lo |
| 27 | 104033C2 | 2 | SCREW, SELF TAPPING, Cross Wash Hd, M4.8 x 19, Coated, self-tapping, truss head, No. 10 – 16 x |
| 1 | 96755C6 | 1 | ROOF, cab |
| 2 | 98355C1 | 1 | INSULATION, FOAM, SEAL – roof, 810 mm (31-7/8 inch) long |
| 3 | 98356C1 | 1 | SEAL ASSY., 5100 mm (200-7/8 inch), cut from 1974883CX bulk seal |
| 4 | 98358C1 | 2 | STRIP, SEAL – 210 mm (8-17/64 inch) long, cut from 1974883CX bulk seal |
| 5 | 98359C1 | 1 | STRIP, SEAL – 100 mm (3-16/16 inch) long, cut from 1974883CX bulk seal |
| 9 | 96814C3 | 8 | WASHER, flat, special, sector arm |
| 13 | 1330157C1 | 8 | NUT, self-locking, hex flange, special, 1/4 inch NC |
| 14 | 97029C3 | 1 | COVER ASSY, support |
| 22 | 1981897C1 | 2 | HINGE, cover, support |
| 23 | 413-416 | 4 | BOLT, Hex, 1/4″-20 x 1″, G5 |
| 24 | 231-1444 | 8 | NUT, LOCK, 1/4″-20, GB |
| 27 | 417-440 | 2 | BOLT, Sq Hd, 1/4″-20 x 2 1/2″, G2, BOLT – square head, 1/4 NC x 2-1/2 inch, grade 2 |
| 28 | 1971364C1 | 2 | RETAINER, bolt |
| 29 | 1340216C1 | 2 | BUTTON, KNOB – retaining, cover |
| 30 | 195-81032 | 12 | WASHER, .266″ x 13/16″ x .083″, flat, 17/64 x 13/16 x 3/32 inch |
| 31 | 1340093C2 | 2 | PLATE, LARGE, STRAP – knob retaining |
| 33 | 1975760C2 | 1 | COVER, wiper arm |
| 34 | 414-410 | 2 | BOLT, Hex, 1/4″-28 x 5/8″, G5, Full Thd, BOLT – hex, 1/4 NF x 5/8 inch, polyseal |
| 35 | 1977988C1 | 6 | FOAM, PAD – foam, filler (Anti-bird) |
| 1 | 1343890C2 | 1 | DOOR, FRAME – cab door |
| 2 | 1977941C2 | 1 | LATCH ASSY., door, rotary |
| 3 | 413-412 | 3 | BOLT, Hex, 1/4″-20 x 3/4″, G5, Full Thd |
| 4 | 493-81002 | 3 | WASHER, LOCK, Ext-Int Tooth, 1/4″, internal-external tooth, 1/4 inch |
| 5 | A177435 | 1 | KNOB,BALL, lever |
| 8 | 97112C3 | 1 | ARM, latch, door |
| 9 | 439-148 | 3 | PIN, HEADED, 1/4″ x 1/2″, headed, 1/4 x 1/2 inch, grade 2, mounting, arm |
| 13 | 1974835C1 | 1 | TUBE, HOSE – spring damper |
| 14 | 97057C2 | 1 | SPRING, TENSION, handle |
| 16 | 97218C1 | 1 | BRACKET, mounting, spring |
| 17 | 413-48 | 1 | BOLT, Hex, 1/4″-20 x 1/2″, G5, Full Thd, hex, 1/4 NC x 1/2 inch |
| 18 | 425-104 | 1 | NUT, 1/4″-20, G5 |
| 20 | 432-88 | 3 | PIN, SPLIT (COTTER), 1/8″ x 1/2″ |
| 21 | 1340019C3 | 1 | CABLE, door, replaces 1340019C2 cable |
| 22 | 1340149C2 | 1 | HANDLE, door, outer |
| 25 | 409-748 | 3 | BOLT, Hex Flg, 1/4″-20 x 1/2″, Serr |
| 26 | 1987149C1 | 1 | HANDLE, grab, door |
| 27 | 1330156C1 | 2 | BOLT, self-locking, hex flange, special, 5/16 NC x 3/4 inch |
| 28 | 195-81005 | 2 | WASHER, 3/8″ x 7/8″ x .083″, flat, 3/8 x 7/8 x 5/64 inch |
| 29 | 1990761C2 | 1 | SEAL, DOOR, 4483 mm (176 – 1/2 inch) long, door, replaces 1990761C1 seal |
| 30 | 1974873C1 | 1 | WASHER, GASKET – handle, door, large |
| 31 | 1974872C1 | 1 | WASHER, GASKET – handle, door, small |
| 33 | 96840C1 | 1 | HANDLE, grab |
| 34 | 1283589C2 | 2 | WASHER, PAD – mounting, handle |
| 35 | 409-7512 | 2 | BOLT, Hex Flg, 5/16″-18 x 3/4″, Serr, Replaces 1330156C1 bolt |
| 36 | 1283690C1 | 1 | ROD, guard, handle |
| 37 | 409-748 | 2 | BOLT, Hex Flg, 1/4″-20 x 1/2″, Serr |
| 40 | 97082C6 | 1 | PANEL ASSY., door |
| 41 | 104033C2 | 2 | SCREW, SELF TAPPING, Cross Wash Hd, M4.8 x 19, Coated, self-tapping, truss head, No. 10-16 x |
| 41 | 1990951C1 | 2 | SCREW, Phillips washer, No. 10-16 x 5/8 inch (Gray) |
| 42 | 96736C2 | 1 | PANEL ASSY., trim, door |
| 43 | 97207C1 | 3 | SCREW, self-tapping, No. 10-24 x 3/4 inch (Black) |
| 43 | 1990953C1 | 3 | SCREW, Phillips washer, No. 10-24 x 1 inch (Gray) |
| 47 | 118071C2 | 1 | SCREW, pan Phillips, self-tapping, No. 8 NC x 1/2 inch |
| 48 | 495-21019 | 1 | WASHER, #8 |
| 49 | 1283695C1 | 1 | STIFFENER, REINFORCEMENT – door handle |
| 50 | 1977459C1 | 3 | INSULATOR, SHEET – vibration dampening, 100 x 254 mm |
| 51 | 1977658C1 | 1 | LINING, PAD – door, upper |
| 52 | 1977657C1 | 1 | LINING, PAD – door, lower |
| 53 | 179093 | 1 | BUTTON, HOLE PLUG, 9/32″, 9/32 inch ID |
| 54 | 1975713C1 | 4 | FASTENER, velcro, 1-1/2 x 1 inch, if used, not shown |
| 1 | 1343890C2 | 1 | DOOR, FRAME – cab door, see fig. 9-112, item 40 for panel, Includes: REF 1, 9, 12 thru 15, 19 & 27 |
| 2 | 1280263C1 | 1 | CYLINDER ASSY., door |
| 3 | 3233348R1 | 2 | CLIP, retaining |
| 4 | 3234063R1 | 2 | BALL JOINT, STUD – ball, 1-9/32 inch long, if used |
| 4 | 142597A1 | 2 | STUD, ball, 1-17/32 inch long, if used |
| 5 | 829-2410 | 1 | NUT, M10 x 1.5, Flg, Cl 10 |
| 9 | 96627C2 | 1 | HINGE, door, upper, Includes: REF 1, 9, 12 thru 15, 19 & 27, plus one each of items 3 and 4 are |
| 10 | 121-116 | 2 | BOLT, Hex Flg, 5/16″-18 x 1″, Serr |
| 11 | 195-81005 | 2 | WASHER, 3/8″ x 7/8″ x .083″, flat, 3/8 x 7/8 x 5/64 inch |
| 12 | 231800A1 | 4 | BUSHING, hinge, replaces 96676C2 bushing, Includes: REF 1, 9, 12 thru 15, 19 & 27, plus one each |
| 13 | 231-4115 | 2 | NUT, LOCK, 5/16″-18, GB, , Includes: REF 1, 9, 12 thru 15, 19 & 27, plus one each of items 3 and 4 |
| 14 | 495-11034 | 2 | WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch, Includes: REF 1, 9, 12 thru 15, 19 & 27, plus |
| 15 | 413-548 | 2 | BOLT, Hex, 5/16″-18 x 3″, G5, BOLT – hex, 5/16 NC x 3 inch, Includes: REF 1, 9, 12 thru 15, 19 & 27 |
| 19 | 96623C2 | 1 | HINGE, door, lower, Includes: REF 1, 9, 12 thru 15, 19 & 27, plus one each of items 3 and 4 are |
| 20 | 121-116 | 3 | BOLT, Hex Flg, 5/16″-18 x 1″, Serr |
| 21 | 195-81005 | 3 | WASHER, 3/8″ x 7/8″ x .083″, flat, 3/8 x 7/8 x 5/64 inch |
| 23 | 1283245C3 | 1 | PLATE ASSY., striker |
| 24 | 1283244C1 | 1 | PLATE ASSY., tapping |
| 26 | 409-7516 | 2 | BOLT, Hex Flg, 5/16″-18 x 1″, Serr |
| 27 | 396-31041 | 1 | WASHER, 13/32″ x 13/16″ x .134″, HDN, , Includes: REF 1, 9, 12 thru 15, 19 & 27, plus one each of |
| 1 | 232329A1 | 1 | GLASS, window, rear, replaces 1999977C2 glass |
| 2 | 1999976C1 | 1 | SEAL, glass, window |
| 3 | F66089 | 1 | PLUG, 3/8 inch diameter, window |
| 4 | F66090 | 1 | PLUG, 29/32 inch diameter, window |
| 6 | K303501 | 2 | SPACER, rubber |
| 7 | K303571 | 2 | WASHER, flat, 6 mm |
| 10 | K303517 | 2 | PIN, LARGE, hinge |
| 11 | 800-418 | 2 | RING, SNAP, M8, Ext, external retaining, No. 8, replaces 31355R1 ring |
| 12 | 1999808C1 | 2 | HINGE, window |
| 13 | 107135A1 | 2 | SCREW, BOLT – hex flange |
| 14 | 97005C1 | 2 | NUT, hex flange, self-locking, special, 6 mm – 1 |
| 19 | 1330064C1 | 2 | NUT, hex flange, self-locking, polyseal, 5/16 inch NC |
| 20 | 138739A1 | 2 | SUPPORT, BRACKET – cylinder |
| 21 | 109587C2 | 2 | PAD, bracket |
| 22 | 109171C1 | 4 | BUSHING, bolt |
| 25 | 97005C1 | 4 | NUT, hex flange, self-locking, special, 6 mm – 1 |
| 26 | 97006C1 | 4 | BOLT, BOLT – hex flange, special, 6 – 1 x 20 mm |
| 27 | 1343825C1 | 2 | SHOCK ABSORBER, CYLINDER – gas spring |
| 28 | 1999766C1 | 2 | BALL JOINT, STUD |
| 29 | 1340207C1 | 1 | PLUG, window hinge |
| 30 | 1340205C1 | 1 | HANDLE, rear window, for service order 19491OA1 handle |
| 31 | 825-1406 | 1 | NUT, M6, Cl 8 |
| 32 | 1340206C1 | 1 | BUSHING, LARGE, rubber |
| 33 | 895-11012 | 1 | WASHER, M12 x 24 x 2.5, flat, 13.5 x 24 x 2 5 mm |
| 34 | 38-21010 | 1 | PIN, 5/32″ x 5/8″, Coiled, 5/32″ x 5/8″, Coiled, replaces 19443R1 pin |
| 35 | 1340202C1 | 1 | PLATE, clamping, for service order 224730A1 handle |
| 36 | 1340208C1 | 2 | PAD, RUBBER, PAD – rubber |
| 37 | 1340203C1 | 1 | PLATE, clamping |
| 38 | 97011C1 | 2 | SCREW, BOLT – hex flange, special |
| 39 | 97005C1 | 2 | NUT, hex flange, self-locking, special, 6 mm – 1 |
| 42 | 1340142C1 | 1 | PLATE, striker |
| 43 | 261-34720 | 2 | SCREW, SELF TAPPING, Cross Pan Hd, 1/4″ x 1 1/4″, self-tapping, pan head Phillips, 1/4 NC x 1-1/4 |
| 44 | 97017C1 | 2 | INSERT, threaded, 6 mm, if used |
| 46 | 1340207C1 | 1 | PLUG, window hinge |
| 47 | 1340205C1 | 1 | HANDLE, rear window, for service order 194910A1 handle |
| 48 | 614-6020 | 1 | BOLT, Hex, M6 x 20, 8.8, Full threads |
| 49 | 1340206C1 | 1 | BUSHING, LARGE, rubber |
| 50 | 895-11012 | 1 | WASHER, M12 x 24 x 2.5, flat, 13.5 x 24 x 2.5 mm |
| 51 | 38-21010 | 1 | PIN, 5/32″ x 5/8″, Coiled, 5/32″ x 5/8″, Coiled |
| 52 | 194322A1 | 1 | PLATE, clamping, for service order 224730A1 handle |
| 53 | 224734A1 | 1 | PLUG, window hinge |
| 54 | 224731A1 | 1 | HANDLE, rear window |
| 55 | 825-1408 | 1 | NUT, M8, Cl 8 |
| 56 | 1340206C1 | 1 | BUSHING, LARGE, rubber |
| 57 | 895-11012 | 1 | WASHER, M12 x 24 x 2.5, flat, 13.5 x 24 x 2.5 mm |
| 58 | 38-21010 | 1 | PIN, 5/32″ x 5/8″, Coiled, 5/32″ x 5/8″, Coiled |
| 59 | 224732A1 | 1 | PLATE ASSY., clamping |
| 1 | 129-500 | 2 | NUT, WING, #10-32, wing, No. 10 NC |
| 2 | A165352 | 1 | PLATE, cable access |
| 3 | A165354 | 2 | SEAL, cable access |