CASE IH Magnum tractor 8940
CASE IH Magnum tractor 8940 — parts list, part 1 of 4
3,603 part numbers across 1 assemblies, transcribed from the catalogue above and split over 4 pages. Search a page for a part number to find the assembly it belongs to; the page links are below the list.
Parts list
| Pos | Part no. | Qty | Description |
|---|---|---|---|
| 1 | 140501A2 | 1 | RADIATOR, ASSEMBLY – cooling system (8930)(Shown) (See Figure 2-6) |
| 1 | 131751A2 | 1 | RADIATOR, ASSEMBLY – cooling system (8940)(See Figure 2-6) |
| 1 | 232545A1 | 1 | RADIATOR, ASSEMBLY – cooling system (8950)(See Figure 2-6) |
| 2 | A170241 | 1 | CAP, RADIATOR, radiator, 15 psi, if used, Reference 2 and 9, 10 and 11 are used on models with the |
| 3 | 217-103 | 1 | COCK, DRAIN, VALVE – 1/4 inch PT |
| 4 | 186489A1 | 1 | HOSE, LARGE, radiator, lower (8930 and 8940)(Shown) |
| 4 | 254335A1 | 1 | HOSE, LARGE, radiator, lower (8950), replaces 235912A1 hose |
| 5 | 198883A1 | 1 | CLAMP, lower radiator hose, radiator side |
| 6 | 138773A1 | 1 | CLAMP, lower radiator hose, engine side |
| 7 | 184299A1 | 1 | HOSE, LARGE, radiator, upper |
| 8 | 138773A1 | 2 | CLAMP, upper radiator hose |
| 9 | 217-151 | 1 | FITTING, 3/8″ Hose X 1/4″ NPTF Beaded, Adapter – straight, vent hose, if used, Reference 2 and 9, 10 |
| 10 | 1960764C1 | 1 | HOSE, 560 mm (22 inch) long, radiator vent to engine, if used, Reference 2 and 9, 10 and 11 are used |
| 11 | 1348264C1 | 2 | CLAMP, HOSE, hose, 3/8 inch, radiator vent hose, if used, Reference 2 and 9, 10 and 11 are used on |
| 12 | L18337 | 1 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch, vent hose to upper radiator hose |
| 13 | 227240A1 | 1 | GASKET, rubber seal, tank replacement |
| 14 | J907208 | 1 | TUBE, water inlet |
| 15 | 845-8016 | 1 | BOLT, Hex Flg, M8 x 16, 8.8, Full Thd |
| 16 | J922847 | 1 | CLAMP, tube |
| 17 | 237-6008 | 1 | O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk |
| 18 | 196816C1 | 1 | FITTING, ADAPTER – barb stem, radiator, lower |
| 19 | 3225216R2 | 1 | HOSE, LARGE, 15 (5/8) ID x 460 mm (18-1/8 inch) long, cut from 97252CX bulk hose, high |
| 20 | 1954736C1 | 2 | CLAMP, HOSE, adjustable |
| 21 | 1301342C1 | 1 | FITTING, ADAPTER – straight, special |
| 22 | 184111A2 | 1 | SUPPORT, BRACKET – radiator, upper |
| 23 | 184112A2 | 1 | SUPPORT, BRACKET – radiator, left-hand side |
| 24 | 184113A2 | 1 | SUPPORT, BRACKET – radiator, right-hand side |
| 25 | 844-8016 | 2 | BOLT, Hex Flg, M8 x 16, 8.8, Upper bracket to radiator, outer mounting holes |
| 26 | 614-6016 | 2 | BOLT, Hex, M6 x 16, 8.8, Upper bracket inner mounting holes |
| 27 | 495-81107 | 2 | WASHER, .281″ x 7/8″ x .060″, flat, 9/32 x 7/8 x 3/64 inch |
| 28 | 844-8018 | 5 | BOLT, Hex Flg, M8 x 18, 8.8, hex, 8 – 1.25 x 16 mm, left-hand and right-hand brackets center |
| 30 | 177080A1 | 2 | SUPPORT, BRACKET – radiator support |
| 31 | 844-10030 | 4 | BOLT, Hex Flg, M10 x 30, 8.8, Full Thd, BOLT – heavy hex flange, 10 – 1.5 x 30 mm, support bracket |
| 32 | 495-81140 | 4 | WASHER, 13/32″ x 1 1/4″ x .060″ |
| 33 | 60-6650T1 | 4 | BUSHING, RUBBER, CUSHION, mount, radiator support bracket lower mounting holes |
| 34 | 234017A1 | 6 | SCREW, BOLT – hex socket, 8 – 1.25 x 16 mm, upper mounting holes |
| 35 | 223350A2 | 1 | PLATE, LARGE, radiator |
| 36 | 864-10016 | 2 | SCREW, Hex Soc Hd, M10 x 16, 8.8 |
| 37 | 141002A2 | 1 | DEFLECTOR, SHROUD – fan (8930 and 8940)(Shown), replaces 141002A1 shroud |
| 37 | 233701A1 | 1 | DEFLECTOR, SHROUD – fan (8950) |
| 38 | 844-8012 | 10 | BOLT, Hex Flg, M8 x 12, 8.8, Full Thd, Replaces 844-8016 16 mm long bolt used on some models |
| 39 | 187107A1 | 3 | SEAL, adhesive back, 608 mm (23-15/16 inch) long, upper and lower fan shroud and upper radiator |
| 40 | 185672A2 | 1 | SEAL, trim, 3010 mm (118-1/2 inch) long, hood perimeter |
| 41 | 256990A1 | 1 | SEAL, adhesive back, 764 mm (30-5/64 inch) long, radiator, lower frame between radiator and |
| 42 | 177362A2 | 8 | SEAL, trim, 55 mm (2-11/64 inch) long, hood, radiator frame and bolster plate |
| 43 | 245983A1 | 2 | SEAL ASSY., TRIM – edge, black, 28 mm (1-1/8 inch) long, attach to vertical leg at rear, cut from |
| 29 | 895-15008 | 4 | WASHER, M8 x 20 x 1.6 |
| 1 | 243898A1 | 1 | TANK, radiator, upper |
| 2 | 243895A1 | 1 | RESERVOIR, TANK – radiator, lower |
| 3 | 227240A1 | 2 | GASKET, rubber seal |
| 5 | 243899A1 | 2 | SUPPORT, radiator |
| 6 | 614-8012 | 8 | BOLT, Hex, M8 x 12, 8.8, Full Thd |
| 7 | 895-15008 | 8 | WASHER, M8 x 20 x 1.6 |
| 1 | 140939A1 | 1 | FAN, engine, prior to serial number JJA0077281, 8930 and 8940 |
| 1 | 256991A1 | 1 | FAN, engine, serial number JJA0077281 and after, 8930 and 8940 |
| 2 | 231413A2 | 1 | DRIVE ASSY., fan, 8930 and 8940 |
| 3 | 614-10030 | 4 | BOLT, Hex, M10 x 30, 8.8, 8930 and 8940 |
| 4 | 892-11010 | 4 | WASHER, LOCK, M10, 8930 and 8940 |
| 5 | 496-11034 | 6 | WASHER, 11/32″ x 11/16″ x 1/16″, HDN, 8930 and 8940 |
| 6 | 825-1408 | 6 | NUT, M8, Cl 8, 8930 and 8940 |
| 7 | J911567 | 1 | BELT, fan, V-ribbed, 1702 mm long, 8930 and 8940 |
| 11 | 256992A1 | 1 | FAN, engine, replaces 229583A1 fan, 8950, tractor |
| 12 | 229596A2 | 1 | DRIVE ASSY., fan, 8950, tractor |
| 13 | 614-10030 | 4 | BOLT, Hex, M10 x 30, 8.8, 8950, Tractor |
| 14 | 892-11010 | 4 | WASHER, LOCK, M10, 8950, tractor |
| 15 | 496-11034 | 6 | WASHER, 11/32″ x 11/16″ x 1/16″, HDN, 8950 Tractor |
| 16 | 825-1408 | 6 | NUT, M8, Cl 8, 8950, tractor |
| 17 | J911567 | 1 | BELT, fan, V-ribbed, 1702 mm long, 8950, tractor |
| 18 | 252078A1 | 1 | FAN, engine, direct drive, 625 mm (24-5/8 inch) diameter, not shown, 8950 heavy duty fan, tractor |
| 19 | A189318 | 1 | SPACER, fan mounting, not shown, 8950 heavy duty fan, tractor |
| 20 | 814-10110 | 4 | BOLT, Hex, M10 x 110, 8.8, Not shown, 8950 heavy duty fan, tractor |
| 21 | 496-21041 | 4 | WASHER, 13/32″ x 13/16″ x .089″, HDN, Not shown, 8950 heavy duty fan, tractor |
| 2 | A172261 | 1 | HOSE, LARGE, 1800 mm (70-7/8 inch) long, cut from L126767 bulk hose, coolant bottle to radiator |
| 3 | 142713A1 | 1 | HOSE, LARGE, 1021 mm (40-7/32 inch) long, coolant recovery overflow |
| 4 | A171099 | 3 | CLAMP, HOSE, spring-type, hose retaining |
| 5 | 188891A1 | 1 | RESERVOIR, coolant container |
| 6 | 1547924C1 | 1 | CAP, recovery bottle, non-vented |
| 2 | 294886A1 | 1 | PLUG, ADAPTER – straight, 1/8-17 NPTF with No. 8 NC tapped hole, not shown |
| 3 | 493-41017 | 1 | WASHER, LOCK, Ext, #8, external tooth lock, No. 8, not shown |
| 4 | 440-1086 | 1 | SCREW, Cross Pan Hd, #8-32 x 3/8″, machine, pan Phillips, No. 8 NC x 3/8 inch, not shown |
| 5 | 294885A1 | 1 | GAUGE, ASSEMBLY – sight glass, not shown, Includes: Ref. 6 |
| 6 | 238-5115 | 1 | O-RING, -115, 70 Duro, .674″ ID x .103″ Thk, Not shown |
| 7 | 253031A1 | 1 | PLATE, LARGE, support, tank |
| 8 | 252716A1 | 1 | SUPPORT, BRACKET – left-hand, tank support |
| 9 | 854-12035 | 2 | BOLT, Hex Flg, M12 x 35, 10.9, BOLT – heavy hex flange, 12 – 1.75 x 35 mm, class 10.9 |
| 10 | 252720A1 | 1 | SUPPORT, BRACKET – tank support |
| 11 | 814-10070 | 1 | BOLT, Hex, M10 x 70, 8.8, BOLT – hex, 10 – 1.5 x 70 mm, replaces 854-10070 hex flange head bolt |
| 12 | 253030A1 | 2 | FIXING BRACKET, CLAMP – band, upper |
| 13 | 254145A1 | 2 | CLAMP, band, lower |
| 14 | 905-10030 | 7 | BOLT, Hex Serr Flg, M10 x 30, BOLT – hex serrated flange, 10 – 1.5 x 30 mm |
| 15 | 825-51410 | 5 | NUT, M10, Flg Ser |
| 16 | 86568834 | 1 | PLUG, Hex Hd, 1/4″-18 NPTF, Radiator, Replaces radiator vent to engine hose (Ref 10, Figure 2-2) |
| 17 | 86643151 | 1 | PLUG, Hex Hd, 1/8″-27 NPTF, hex, 1/8 inch PT, radiator |
| 18 | 301472A1 | 1 | CAP, FILLER, 10 psi, deaeration tank, replaces A149609 cap |
| 19 | 142713A1 | 1 | HOSE, LARGE, 1021 mm (40-7/32 inch) long, coolant overflow |
| 20 | A171099 | 1 | CLAMP, HOSE, spring-type |
| 21 | 253866A1 | 1 | CABLE, WIRE – ground, tank to mounting plate |
| 22 | 895-18010 | 1 | WASHER, M10 x 18 x 1.6 |
| 23 | 253784A1 | 1 | HOSE, 19 (3/4) x 27 (1-1/16) x 1785 mm (70-5/16 inch) long, return |
| 24 | 214-1412 | 1 | CLAMP, HOSE, #12, 0.69/1.25 Type F Worm |
| 25 | 217-185 | 1 | FITTING, 45є, 3/4″ Hose x 1/2″ NPTF Beaded, 45 degree, 3/4 stem end x 1/2 inch PT |
| 26 | 214-1316 | 1 | CLAMP, HOSE, #16, 1″, Spring, CLAMP – spring type, 1 inch |
| 27 | 279476A1 | 1 | SENSOR, low coolant, probe, coolant level, replaces A145513 sensor |
| 28 | 253865A1 | 1 | CABLE, WIRE – coolant level extension (Prior to P.I.N. JJA0076314) |
| 29 | 824-1405 | 1 | NUT, M5, Cl 5 |
| 30 | 253764A1 | 1 | HOSE, 8 (5/16) x 14 (9/16) x 1520 mm (59-7/8 inch) long, engine cylinder head to deaeration tank |
| 31 | A172261 | 1 | HOSE, LARGE, 1800 mm (70-7/8 inch) long, cut from L126767 bulk hose, radiator to deaeration tank |
| 32 | A171099 | 4 | CLAMP, HOSE, spring-type |
| 33 | 241173A1 | 1 | FITTING, ORIFICE – straight, 0.120 inch hole, 1/8 PT x 5/16 inch stem end |
| 34 | 253858A1 | 1 | PLUG, CAP – radiator, non-opening |
| 2 | 294886A1 | 1 | PLUG, ADAPTER – straight, 1/8-17 NPTF with No. 8 NC tapped hole, not shown |
| 3 | 493-41017 | 1 | WASHER, LOCK, Ext, #8, external tooth, No. 8, not shown |
| 4 | 440-1086 | 1 | SCREW, Cross Pan Hd, #8-32 x 3/8″, machine, pan Phillips, No. 8 NC x 3/8 inch, not shown |
| 5 | 294885A1 | 1 | GAUGE, ASSEMBLY – sight glass, not shown, Includes: Ref. 6 |
| 6 | 238-5115 | 1 | O-RING, -115, 70 Duro, .674″ ID x .103″ Thk, Not shown |
| 7 | 278863A2 | 1 | SUPPORT, PLATE, deaeration tank/air cleaner, see Figure 2-13A for mounting hardware |
| 10 | 9804279 | 4 | NUT, M12 x 1.75, Flg, Cl 8, hex flange, 12 mm – 1.75, Part of the Deaeration Kit P/N 324239A1. |
| 11 | 301472A1 | 1 | CAP, FILLER, 10 psi, deaeration tank, replaces A149609 cap |
| 12 | 142713A1 | 1 | HOSE, LARGE, 1021 mm (40-7/32 inch) long, coolant overflow |
| 13 | A171099 | 1 | CLAMP, HOSE, spring-type |
| 15 | 214-1316 | 1 | CLAMP, HOSE, #16, 1″, Spring, CLAMP – spring type, 1 inch |
| 16 | 253784A1 | 1 | HOSE, 19 (3/4) x 27 (1-1/16) x 1785 mm (70-5/16 inch) long, return |
| 17 | 217-185 | 1 | FITTING, 45є, 3/4″ Hose x 1/2″ NPTF Beaded, 45 degree, 3/4 stem end x 1/2 inch PT |
| 18 | 214-1412 | 2 | CLAMP, HOSE, #12, 0.69/1.25 Type F Worm |
| 19 | 279476A1 | 1 | SENSOR, low coolant, probe, coolant level, replaces A145513 sensor |
| 20 | 253865A1 | 1 | CABLE, WIRE – coolant level extension (Prior to P.I.N. JJA0076314) |
| 21 | 824-1405 | 1 | NUT, M5, Cl 5 |
| 22 | 253764A1 | 1 | HOSE, 8 (5/16) x 14 (9/16) x 1520 mm (59-7/8 inch) long, engine cylinder head to deaeration tank |
| 23 | 241173A1 | 1 | FITTING, ORIFICE – straight, 0.120 inch hole, 1/8 PT x 5/16 inch stem end |
| 24 | J911901 | 1 | VALVE, CHECK, check |
| 25 | A171099 | 4 | CLAMP, HOSE, spring-type |
| 26 | A172261 | 1 | HOSE, LARGE, 1800 mm (70-7/8 inch) long, cut from L126767 bulk hose, radiator to deaeration tank |
| 27 | 253858A1 | 1 | PLUG, CAP – radiator, non-opening |
| 28 | 138773A1 | 2 | CLAMP, radiator hose |
| 29 | 86568834 | 1 | PLUG, Hex Hd, 1/4″-18 NPTF, Radiator, Replaces radiator vent to engine hose (Ref 10, Figure 2-2) |
| 30 | 86643151 | 1 | PLUG, Hex Hd, 1/8″-27 NPTF, hex, 1/8 inch PT, radiator |
| 31 | 311254A1 | 1 | PLATE, LARGE, support, deaeration tank, if used, Part of the Deaeration Kit P/N 324239A1. |
| 1 | 113077A1 | 1 | AIR CLEANER, ASSEMBLY – air, includes precleaner, parts list Figure 2-14, Includes: Ref. 2 |
| 3 | 1289073C3 | 1 | HOSE, LARGE, air cleaner to turbocharger |
| 4 | 214-3280 | 1 | CLAMP, HOSE, 4.25/5.125 HD Worm, W/liner |
| 5 | P6137737 | 1 | INDICATOR, SWITCH – restriction, air cleaner, replaces 1983640C1 switch |
| 6 | 214-3288 | 1 | CLAMP, HOSE, 4.75/5.625 HD Worm, W/liner, adj, 4-3/4 – 5-5/8 inch dia. |
| 7 | 1975782C1 | 3 | SCREW, SELF TAPPING, Cross Truss Wash Hd, #10 x 5/8″, Precleaner to air duct |
| 11 | 1998851C1 | 1 | HOSE, LARGE, 90 degree, aspirator |
| 12 | 121746A1 | 1 | PIPE, SUCTION, TUBE – aspirator |
| 13 | 1998858C1 | 1 | HOSE, LARGE, aspirator |
| 14 | 214-1428 | 4 | CLAMP, HOSE, #28, 1.31/2.25 Type F Worm |
| 16 | 1334309C2 | 1 | COLLAR CLAMP, aspirator tube, mounts to turbo shield |
| 17 | 905-10025 | 1 | BOLT, Hex Serr Flg, M10 x 25 |
| 18 | 829-2410 | 1 | NUT, M10 x 1.5, Flg, Cl 10 |
| 19 | 814-10060 | 1 | BOLT, Hex, M10 x 60, 8.8 |
| 21 | A176570 | 1 | SPACER, clamp |
| 22 | 829-2410 | 1 | NUT, M10 x 1.5, Flg, Cl 10 |
| 23 | 1348516C3 | 1 | SUPPORT, BRACKET – plate, air cleaner |
| 24 | 905-10020 | 3 | BOLT, Hex Serr Flg, M10 x 20 |
| 25 | 1348518C1 | 1 | SUPPORT, BRACKET – air cleaner, mounts to cylinder head |
| 26 | 905-10025 | 2 | BOLT, Hex Serr Flg, M10 x 25 |
| 27 | 829-2410 | 1 | NUT, M10 x 1.5, Flg, Cl 10 |
| 28 | 1340702C1 | 1 | SUPPORT, air cleaner |
| 29 | 905-8012 | 1 | BOLT, Hex Serr Flg, M8 x 12 |
| 30 | 1348517C1 | 1 | SUPPORT, BRACKET – air cleaner mounting, mounts to cylinder head |
| 31 | 905-10025 | 1 | BOLT, Hex Serr Flg, M10 x 25 |
| 32 | 829-2410 | 1 | NUT, M10 x 1.5, Flg, Cl 10 |
| 33 | 814-10060 | 1 | BOLT, Hex, M10 x 60, 8.8 |
| 35 | A176570 | 1 | SPACER, clamp |
| 36 | 142742A1 | 1 | DUCT, air intake |
| 37 | 96900C1 | 3 | NUT, U, #10-16, Panel type |
| 20 | 895-11010 | 1 | WASHER, M10 x 20 x 2 |
| 34 | 895-11010 | 1 | WASHER, M10 x 20 x 2 |
| 1 | 113077A1 | 1 | AIR CLEANER, ASSEMBLY – air, includes precleaner, parts list Figure 2-14, Includes: Ref. 2 |
| 3 | 1289073C3 | 1 | HOSE, LARGE, air cleaner to turbocharger |
| 4 | 214-3280 | 1 | CLAMP, HOSE, 4.25/5.125 HD Worm, W/liner, Adjustable |
| 5 | P6137737 | 1 | INDICATOR, SWITCH – restriction, air cleaner, replaces 1983640C1 switch |
| 6 | 214-3288 | 1 | CLAMP, HOSE, 4.75/5.625 HD Worm, W/liner, adj, 4-3/4 – 5-5/8 inch dia |
| 7 | 93199C1 | 3 | FASTENER, ratchet, precleaner to air duct |
| 11 | 1998851C1 | 1 | HOSE, LARGE, 90 degree, aspirator |
| 12 | 121746A1 | 1 | PIPE, SUCTION, TUBE – aspirator |
| 13 | 1998858C1 | 1 | HOSE, LARGE, aspirator |
| 14 | 214-1428 | 3 | CLAMP, HOSE, #28, 1.31/2.25 Type F Worm |
| 16 | 1334309C2 | 1 | COLLAR CLAMP, aspirator tube, mounts to turbo shield |
| 17 | 905-10025 | 1 | BOLT, Hex Serr Flg, M10 x 25 |
| 18 | 829-2410 | 1 | NUT, M10 x 1.5, Flg, Cl 10 |
| 19 | 814-10060 | 1 | BOLT, Hex, M10 x 60, 8.8 |
| 21 | A176570 | 1 | SPACER, clamp |
| 22 | 829-2410 | 1 | NUT, M10 x 1.5, Flg, Cl 10 |
| 23 | 278863A2 | 1 | SUPPORT, PLATE – deaeration tank/air cleaner |
| 24 | 905-10020 | 3 | BOLT, Hex Serr Flg, M10 x 20 |
| 25 | 1348518C1 | 1 | SUPPORT, BRACKET – air cleaner, mounts to cylinder head |
| 26 | 905-10025 | 2 | BOLT, Hex Serr Flg, M10 x 25 |
| 27 | 829-2410 | 1 | NUT, M10 x 1.5, Flg, Cl 10 |
| 28 | 1340702C1 | 1 | SUPPORT, air cleaner |
| 29 | 905-8012 | 1 | BOLT, Hex Serr Flg, M8 x 12 |
| 30 | 279325A1 | 1 | SUPPORT ASSY., BRACKET – air cleaner mounting, mounts to cylinder head |
| 31 | 905-10025 | 1 | BOLT, Hex Serr Flg, M10 x 25 |
| 32 | 825-51410 | 1 | NUT, M10, Flg Ser |
| 33 | 905-10020 | 1 | BOLT, Hex Serr Flg, M10 x 20 |
| 36 | 113580A1 | 1 | DUCT, air intake |
| 37 | 96900C1 | 3 | NUT, U, #10-16, Panel type |
| 38 | 214-1432 | 1 | CLAMP, HOSE, #32, 1.56/2.50 Type F Worm, Adjustable |
| 39 | 278862A1 | 1 | SUPPORT, BRACKET – air plate |
| 20 | 895-11010 | 1 | WASHER, M10 x 20 x 2 |
| 3 | A171256 | 1 | FILTER, ELEMENT, secondary |
| 4 | A171255 | 1 | FILTER, ELEMENT, primary |
| 5 | A47134 | 2 | NUT, wing, retaining, element retaining |
| 6 | D37976 | 1 | GASKET, air cleaner element |
| 7 | A184650 | 1 | COVER ASSY, access |
| 8 | 33-1387T1 | 1 | NUT, WING, cover retaining |
| 1 | 185552A2 | 1 | SOLENOID, ASSEMBLY – ether injection, Includes: Ref. 2 |
| 2 | 190752A1 | 1 | HOUSING, ether injection solenoid |
| 3 | 281-34812 | 2 | SCREW, SELF TAPPING, Hex Hd, 5/16″ x 3/4″, self-tapping, hex washer head, 5/16 NC x 3/4 inch |
| 4 | A149932 | 1 | TUBE, 2006 mm (79 inch) long |
| 5 | A172900 | 1 | NOZZLE CAP, ASSEMBLY – atomizer |
| 6 | 217-40 | 1 | REDUCER, 1/4″-18 NPTF x 1/8″-27 Fem NPTF, 1/4 PT x 1/8 inch female PT |
| 7 | L18337 | 3 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch |
| 1 | 1998855C2 | 1 | ELBOW, exhaust casting |
| 2 | 828-12055 | 4 | BOLT, Hex, M12 x 55, 10.9 |
| 3 | 896-11012 | 4 | WASHER, M13.5 x 24.5 x 3, HT |
| 4 | 1998799C2 | 2 | STUD, 12 x 150 mm |
| 5 | 1998800C2 | 1 | STUD, 12 x 60 mm |
| 6 | 896-11012 | 3 | WASHER, M13.5 x 24.5 x 3, HT |
| 7 | 127594A1 | 3 | NUT, hex, 12 mm – 1.75, special |
| 8 | 1998778C2 | 1 | GASKET, muffler, elbow to extension |
| 9 | 1347836C3 | 1 | MUFFLER, PIPE – exhaust, muffler extension (8930 and 8940) if used |
| 9 | 229359A1 | 1 | MUFFLER, PIPE – exhaust, muffler extension (8950) if used |
| 10 | 139789A3 | 1 | MUFFLER, PIPE – exhaust, muffler extension, spark arresting muffler, if used, Includes: plug |
| 12 | A170807 | 1 | CLAMP, retaining, special |
| 13 | 135725A3 | 1 | PIPE ASSY., TUBE – to turbocharger |
| 14 | 180428A2 | 1 | ADAPTER, turbocharger |
| 1 | 1334628C6 | 1 | GUARD, SHIELD – manifold |
| 2 | 614-10016 | 2 | BOLT, Hex, M10 x 16, 8.8, Full Thd |
| 3 | 896-11010 | 2 | WASHER, M10 x 21.5 x 2.5, HT |
| 4 | 102225A2 | 1 | SHIELD, turbocharger |
| 5 | 832-41306 | 2 | NUT, LOCK, M6 x 1, Cl 10, If used |
| 6 | 895-11006 | 2 | WASHER, M6, If Used |
| 7 | 905-10020 | 3 | BOLT, Hex Serr Flg, M10 x 20 |
| 10 | 614-10016 | 2 | BOLT, Hex, M10 x 16, 8.8, Full Thd |
| 11 | 1348399C1 | 2 | NUT, hex serrated flange, 10 – 1.5 mm |
| 12 | 1968122C1 | 1 | SHIELD, starter, front |
| 13 | 614-8016 | 2 | BOLT, Hex, M8 x 16, 8.8, front starter shield to rear starter shield |
| 15 | 1289443C1 | 1 | SHIELD, starter, rear |
| 16 | 614-8012 | 3 | BOLT, Hex, M8 x 12, 8.8, Full Thd |
| 14 | 895-11008 | 5 | WASHER, M8 x 16 x 1.6 |
| 3 | J902089 | 1 | SEAL, sealing |
| 4 | J934054 | 3 | BOLT, hex, flange, 8 – 1.25 x 28 mm, Replaces J926125 bolt |
| 5 | J929458 | 1 | SUPPORT, fan, INCLUDES REFS 6,7,8,9,10 |
| 6 | J907769 | 1 | BOLT, BOLT – hex, special, 10 – 1.5 x 70 mm, class 12.9 |
| 7 | J923044 | 1 | RETAINER, fan hub |
| 8 | 100-21250 | 2 | RING, SNAP, 2.50″, Int, #250 |
| 9 | J910739 | 1 | BEARING, BALL |
| 10 | J911924 | 1 | HUB, fan |
| 11 | 845-8050 | 4 | BOLT, Hex Flg, M8 x 50, 8.8, Fan support to cylinder head |
| 12 | J914462 | 1 | PULLEY, fan, 1.1 to 1 ratio |
| 13 | J925188 | 1 | SUPPORT, BRACKET – belt tensioner |
| 14 | J925186 | 1 | SCREW, COUNTERSUNK, Torx Soc, M8 x 1.25 x 25, Special |
| 15 | 844-8025 | 1 | BOLT, Hex Flg, M8 x 25, 8.8, Mounting Bracket to Cylinder Head |
| 16 | J934817 | 1 | TENSIONER, belt, replaces J918944 tensioner |
| 17 | 854-10075 | 1 | BOLT, Hex Flg, M10 x 75, 10.9, Belt tensioner to mounting bracket |
| 18 | A77817 | 1 | PACKAGE, REPAIR, KIT – belt tensioner pulley, used to replace pulley of J918944 belt tensioner, item |
| 1 | J929446 | 1 | COVER ASSY, gear, front, high PTO |
| 3 | J823494 | 1 | SEALANT, Three Bond Silver RTV Adhesive/Sealer, 3 ounce tube, apply between front gear cover and |
| 4 | J926719 | 1 | MOTOR HOUSING, gear, high PTO, 8930 and 8940 Tractor |
| 4 | J929555 | 1 | TRANSMISSION HOUSING, gear, high mount, 8950 Tractor only, Ref #4 8930 and 8940 used p/n |
| 5 | J929253 | 1 | GASKET, housing, gear |
| 6 | J926863 | 6 | BOLT, BOLT – hex flange, 8 – 1.25 x 50 mm, class 10.9, front gear cover to timing gear housing to |
| 7 | J924962 | 17 | BOLT, hex flange, special, 8 – 1.25 x 16 mm, front gear cover to timing gear housing |
| 8 | J926846 | 5 | BOLT, BOLT – hex flange, 8 – 1.25 x 20 mm, class 10.9, timing gear housing to engine block |
| 9 | J900257 | 2 | PIN, dowel, 16 mm long |
| 10 | J903463 | 1 | COVER, front access |
| 11 | J903475 | 1 | SEAL, front access cover |
| 12 | J914868 | 1 | COVER, PLATE – access, flat, used with item 4 housings |
| 13 | J931608 | 1 | GASKET, access cover plate, used with item 4 housings |
| 14 | 854-12025 | 2 | BOLT, Hex Flg, M12 x 25, 10.9, Heavy, Used with item 4 housings |
| 15 | J905933 | 1 | HOUSING, timing pin |
| 16 | J915772 | 1 | SEALRING, RING – quad, timing pin housing |
| 17 | J907998 | 2 | SCREW, LOCK, Spc Rd Torx Hd, M5 x 17 |
| 18 | J903924 | 1 | PIN, timing |
| 19 | J913994 | 1 | O-RING, sealing |
| 20 | 100-2587 | 1 | RING, SNAP, 0.875″, Int, #87, (Replaces J904849) |
| 21 | A77790 | 1 | KIT, SEALS, oil, crankshaft front, Includes: Ref. 22,23,24,25 |
| 25 | J918113 | 1 | SHIELD, dust |
| 1 | J932183 | 1 | MANIFOLD, EXHAUST, exhaust, replaces J929779 manifold |
| 2 | J929012 | 6 | GASKET, exhaust manifold, 0.54 mm thick |
| 3 | J929537 | 12 | BOLT, BOLT – hex, special, exhaust manifold to cylinder head |
| 4 | J914708 | 12 | PLATE, LOCKING, manifold bolt, exhaust |
| 5 | J922648 | 1 | COVER ASSY, intake manifold |
| 6 | J914311 | 1 | GASKET, intake manifold cover |
| 7 | 845-8030 | 18 | BOLT, Hex Flg, M8 x 30, 8.8, Intake manifold cover to cylinder head |
| 8 | A77429 | 1 | PLUG, hex socket, 1/2 inch PT, intake |
| 1 | J932183 | 1 | MANIFOLD, EXHAUST, exhaust, replaces J929779 |
| 2 | J929012 | 6 | GASKET, exhaust manifold, 0.54 mm thick |
| 2 | J932063 | 6 | GASKET, MANIFOLD, exhaust manifold, high temperature, 1.78 mm thick, 8950 Tractor, if used |
| 3 | J929537 | 12 | BOLT, BOLT – hex, special, exhaust |
| 4 | J914708 | 12 | PLATE, LOCKING, manifold bolt, exhaust |
| 5 | J924732 | 1 | AFTERCOOLER, air intake, aftercooler |
| 6 | J823494 | 1 | SEALANT, Three Bond Silver RTV Adhesive/Sealer, 3 ounce tube, intake manifold aftercooler, not |
| 7 | J918109 | 18 | SCREW, Hex Flg Hd, M8 x 1.25 x 25, Special, Intake aftercooler to cylinder head |
| 8 | J909394 | 1 | COCK, DRAIN, VALVE – air bleed, intake, aftercooler |
| 9 | J918611 | 4 | HOSE, LARGE, 63 mm (2-1/2 inch) long, supply tube to intake aftercooler |
| 10 | J918163 | 8 | CLIP, CLAMP – spring type, hose retaining, intake aftercooler |
| 11 | J906436 | 1 | PIPE ASSY., TUBE – water inlet, intake aftercooler |
| 12 | J908402 | 1 | PIPE ASSY., TUBE – water outlet, intake aftercooler |
| 13 | J917394 | 2 | ELBOW, CONNECTOR – water inlet, intake aftercooler |
| 14 | 238-5120 | 2 | O-RING, -120, 70 Duro, .987″ ID x .103″ Thk, Intake aftercooler |
| 15 | J906439 | 1 | PLATE, mounting, intake aftercooler |
| 16 | 845-8016 | 1 | BOLT, Hex Flg, M8 x 16, 8.8, Full Thd, Intake aftercooler |
| 17 | J910778 | 1 | DECAL, Caution, open during fill, connector to block, intake aftercooler |
| 2 | J911941 | 1 | GASKET, mounting, turbocharger, Part of Turbocharger Assembly Kit P/N J802859, JR802859 |
| 3 | J818823 | 4 | STUD, turbocharger mounting |
| 4 | J818824 | 4 | NUT, hex flange, special, 10 mm – 1.5 |
| 5 | J921530 | 1 | HOSE, FLEXIBLE, turbocharger oil supply |
| 6 | J919687 | 2 | CONNECTOR, ELEC, ADAPTER – female hex, special, Includes: Ref. 7 |
| 7 | 238-5013 | 1 | O-RING, -013, 70 Duro, .426″ ID x .070″ Thk |
| 8 | J928629 | 1 | TUBE, oil drain, Includes: Ref. 8A |
| 9 | J942725 | 1 | GASKET, turbo oil drain, replaces J819378 gasket, Part of Turbocharger Assembly Kit P/N J802859 |
| 10 | 844-8020 | 2 | BOLT, Hex Flg, M8 x 20, 8.8 |
| 11 | J932183 | 1 | MANIFOLD, EXHAUST, exhaust, see Figure 2-26 for mounting parts |
| 15 | J924732 | 1 | AFTERCOOLER, air intake, see Figure 2-26 for mounting and water tubes |
| 16 | J914943 | 1 | TUBE, crossover, air |
| 17 | J924386 | 4 | COLLAR CLAMP, adjustable, special |
| 18 | J916437 | 2 | HOSE, crossover tube |
| 19 | 222-993 | 2 | GASKET, 3/8 Tube, Fl, Copper |
| 1 | J535789 | 1 | TURBOCHARGER, ASSEMBLY – engine, new, 8930 Tractor |
| 1 | J537130 | 1 | TURBOCHARGER, ASSEMBLY – engine, new, 8940 Tractor |
| 1 | J535787 | 1 | TURBOCHARGER, ASSEMBLY – engine, new, 8950 Tractor, replaces J536305 turbocharger |
| 18 | J535243 | 1 | GASKET, adapter |
| 19 | J528010 | 1 | ADAPTER, connection, replaces J533030 adapter |
| 20 | 614-8020 | 5 | BOLT, Hex, M8 x 20, 8.8 |
| 21 | J534309 | 2 | PLATE, clamping, if used |
| 22 | J759917 | 6 | SET SCREW, set, hex head, if used |
| 1 | J535106 | 1 | ACTUATOR, turbo wastegate, 8930 Tractor |
| 1 | J531892 | 1 | ACTUATOR, turbo wastegate, 8940 and 8950 Tractor |
| 2 | J528177 | 1 | LINK, adjusting |
| 3 | 425-155 | 1 | NUT, Jam, 5/16″-24, G5, Hex |
| 4 | J528204 | 1 | NUT, lock |
| 5 | J528221 | 2 | CIRCLIP, retaining |
| 7 | J532195 | 3 | SPACER, mounting, short |
| 8 | J532196 | 1 | SPACER, mounting, long |
| 9 | 814-8055 | 1 | BOLT, Hex, M8 x 55, 8.8, BOLT – hex, 8 – 1.25 x 55 mm |
| 10 | J533328 | 1 | SUPPORT, BRACKET – wastegate actuator |
| 12 | J535874 | 2 | STUD, actuator bracket |
| 6 | 895-11008 | 3 | WASHER, M8 x 16 x 1.6 |
| 1 | J918334 | 1 | HEAD, FILTER, filter, oil |
| 2 | J906619 | 2 | PLUG, hex, 1/8 inch PT |
| 3 | A77722 | 1 | PIN, dowel, locating |
| 4 | A77505 | 1 | PLUG, hex socket, 3/4 inch PT, filter head |
| 5 | J933615 | 1 | VALVE, relief, pressure, replaces J927622 valve |
| 6 | J918532 | 1 | PLUNGER, regulator |
| 7 | A77541 | 1 | SPRING, compression |
| 8 | J919016 | 1 | PLUG, hex, special, 24 mm – 1.50, regulator, required with J922882 cover, Includes: item 9 O-ring, if |
| 9 | 238-5022 | 1 | O-RING, -022, 70 Duro, .989″ ID x .070″ Thk, Used with J919016 plug |
| 10 | 845-8065 | 11 | BOLT, Hex Flg, M8 x 65, 8.8, BOLT – heavy hex flange, 8 – 1.25 x 65 mm, oil filter head to cylinder bloc |
| 11 | J919562 | 1 | FILTER, ENGINE OIL, oil, cartridge, engine |
| 12 | J921605 | 1 | GASKET, filter head |
| 13 | J918175 | 1 | CORE-OIL COOLER |
| 14 | J918174 | 1 | GASKET, cooler core |
| 16 | A77724 | 1 | O-RING, sealing |
| 17 | J922882 | 1 | COVER, oil cooler, must use item 8, J919016 plug with this cover, no longer available, order J931077 |
| 17 | J931077 | 1 | COVER, oil cooler, must use item 8A, J931084 plug with this cover, replaces J922882 cover |
| 18 | J929011 | 1 | GASKET, cooler cover, oil |
| 19 | J907860 | 4 | BOLT, Hex, Flg Hd, M8 x 25, Spcl |
| 20 | 217-439 | 1 | PLUG, Hex Soc, 1/2″-14, hex socket headless, 1/2 inch PT, water drain |
| 1 | J930338 | 1 | PUMP, ENGINE OIL, ASSEMBLY – 24 teeth drive gear |
| 2 | 614-8030 | 4 | BOLT, Hex, M8 x 30, 8.8, Full Thd |
| 3 | J921719 | 1 | TUBE, with screen, oil suction |
| 4 | J926865 | 2 | SPACER, mounting, replaces J908738 spacer |
| 5 | 845-6030 | 2 | BOLT, Hex Flg, M6 x 30, 8.8, BOLT – heavy hex flange, 6 – 1.0 x 30 mm |
| 6 | J914302 | 1 | GASKET, mounting, oil suction tube, Part of Oil Pan Gasket Kit P/N A77679 |
| 7 | 845-6015 | 2 | BOLT, Hex Flg, M6 x 15, 8.8, Full Thd |
| 8 | J906216 | 1 | NUT, hex flange, special, 6 mm – 1.0 |
| 9 | J910960 | 1 | WASHER, flat, special |
| 10 | J927611 | 1 | BRACKET, suction tube |
| 11 | J914015 | 1 | PAN, ENGINE OIL, oil, engine |
| 12 | J920400 | 32 | BOLT, Hex, Flg Hd, M8 x 21, Spcl, hex flange cap, special, 8 – 1.25 x 25 mm, oil pan to block |
| 13 | J910266 | 32 | WASHER, spring, Belleville |
| 14 | J908316 | 32 | WASHER, flat, special, 9 x 16 x 1 mm |
| 15 | J924148 | 1 | PLUG, hex magnetic, special, 22 mm – 1.5, heater hole |
| 16 | J902425 | 1 | WASHER, sealing, plug, Part of Oil Pan Gasket Kit P/N A77679 |
| 17 | J924147 | 1 | PLUG, hex magnetic, special, 12 mm – 1.5, drain |
| 18 | J920773 | 1 | WASHER, SEALING, WASHER – sealing, Part of Oil Pan Gasket Kit P/N A77679 |
| 22 | 196466A1 | 1 | CABLE, ELECTRIC, engine block heater, oil pan heater kit |
| 23 | J902425 | 1 | WASHER, sealing, plug, see note, oil pan heater kit |
| 2 | J930903 | 1 | COVER, VALVE, replaces J927907 cover |
| 3 | J905449 | 1 | SEAL, RUBBER, valve cover |
| 4 | J910824 | 6 | O-RING, cover bolt |
| 5 | J922639 | 6 | STUD, STUD – valve cover and tube, wastegate actuator mounting |
| 6 | J902468 | 1 | PLUG, CAP – oil filler |
| 7 | J902466 | 1 | SEAL, cap |
| 8 | J935585 | 1 | GASKET, cylinder head, standard, replaces J928168 gasket |
| 8 | J935586 | 1 | GASKET, CYLINDER HEAD, 0.25 mm thicker, Replaces J931026 gasket |
| 8 | J935587 | 1 | GASKET, CYLINDER HEAD, 0.50 mm thicker, Replaces J931027 |
| 9 | J907861 | 1 | EYE, LIFTING, lifting, front |
| 10 | J906440 | 1 | EYE, LIFTING, lifting, rear |
| 11 | 614-12025 | 2 | BOLT, Hex, M12 x 25, 8.8, Full threads, Front lifting bracket to cylinder head |
| 12 | J920497 | 1 | ELBOW, CONNECTOR – 90 degree, breather vent, no longer available, order J935113 connector and |
| 12 | J935113 | 1 | ELBOW, CONNECTOR – 90 degree, breather vent, replaces J920497 connector, not shown |
| 13 | 238-5115 | 1 | O-RING, -115, 70 Duro, .674″ ID x .103″ Thk, If used with J920497 connector |
| 13 | J934865 | 1 | SEAL, 17.4 mm ID x 4.3 mm, If used, used with J935113 connector, not shown |
| 14 | J930827 | 1 | HOSE, 51 mm (2 inch) long, to connector, replaces J918610 hose |
| 15 | J934496 | 2 | CLIP, CLAMP – spring type, replaces J918163 clamp |
| 16 | J909669 | 1 | TUBE, breather |
| 17 | J907741 | 1 | CLIP, CLAMP – P-style, tube retaining |
| 18 | J912072 | 1 | SCREW, SELF TAPPING, SCREW – self tapping, hex washer head, special, 8 – 1.25 x 15 mm |
| 19 | A77538 | 1 | CLIP, CLAMP – P-style, tube retaining |
| 20 | 844-12025 | 1 | BOLT, Hex Flg, M12 x 25, 8.8 |
| 21 | J918616 | 1 | HOSE, LARGE, 680 mm (26-3/4 inch) long, tube end, if used |
| 21 | H353854 | 1 | HOSE ASSY., 813 mm (32 inch) long, if used, cut from 364359C2 bulk hose |
| 22 | 214-1318 | 1 | CLAMP, HOSE, #18, 1 1/8″, Spring, If Used |
| 22 | 214-1315 | 1 | CLAMP, HOSE, #15, 15/16″, Spring, If Used |
| 24 | 222-42 | 1 | ELBOW, 90є, 1/2″-24 Fem x 1/8″-27 NPTF, ELBOW – 90 degree, compression, 1/4 tube OD x 1/8 inch |
| 25 | J924589 | 1 | TUBE, vent, air, Includes: Ref. 26 |
| 26 | 222-153 | 2 | SLEEVE, 1/4″ Tube |
| 27 | 222-22 | 1 | FITTING, 1/2″-24 x 1/8″ NPTF w/Nut, ADAPTER – compression, 1/4 tube OD x 1/8 inch PT, tube to |
| 1 | J914310 | 1 | GASKET, thermostat housing |
| 2 | J928639 | 2 | THERMOSTAT, engine coolant |
| 4 | 845-8080 | 2 | BOLT, Hex Flg, M8 x 80, 8.8, BOLT – heavy hex flange, 8 – 1.25 x 80 mm |
| 5 | J912800 | 1 | CONNECTION, TUBE – water outlet |
| 6 | J918779 | 1 | GASKET, outlet tube, water |
| 7 | 845-8095 | 2 | BOLT, Hex Flg, M8 x 95, 8.8, BOLT – heavy hex flange, 8 – 1.25 x 95 mm |
| 8 | J918544 | 1 | SUPPORT, mounting, alternator |
| 9 | 844-8025 | 4 | BOLT, Hex Flg, M8 x 25, 8.8 |
| 10 | 294926A1 | 1 | VALVE, SHUT-OFF, SHAFT – |
| 11 | A77544 | 1 | FILTER, water conditioning, precharge |
| 12 | 238-5111 | 1 | O-RING, -111, 70 Duro, .424″ ID x .103″ Thk |
| 13 | A77623 | 1 | ADAPTER, water filter |
| 14 | 845-6010 | 1 | BOLT, Hex Flg, M6 x 10, 8.8, Full Thd, BOLT – heavy hex flange, 6 – 1.0 x 10 mm |
| 15 | J911925 | 1 | COUPLING, hose |
| 16 | J911901 | 1 | VALVE, CHECK |
| 1 | J920031 | 1 | CYLINDER HEAD, ASSEMBLY – new, without valves, Includes: Ref. 1A-7 |
| 2 | J923564 | 12 | GUIDE, VALVE, valve stem |
| 3 | J924582 | 6 | INSERT, INSERT – intake |
| 3 | J925468 | 6 | SEAT, VALVE, INSERT – intake, 0.254 mm oversize, service repair only, The oversize valve insert is |
| 3 | J925470 | 6 | SEAT, VALVE, INSERT – intake, 0.508 mm oversize, service repair only, The oversize valve insert is |
| 4 | J929005 | 6 | INSERT, seat, exhaust valve |
| 4 | J929006 | 6 | INSERT, seat, exhaust valve, 0.254 mm oversize, service repair only, The oversize valve insert is not |
| 4 | J929007 | 6 | INSERT, seat, exhaust valve, 0.508 mm oversize, service repair only, The oversize valve insert is not |
| 5 | J920443 | 1 | PLUG, expansion, 30 mm OD |
| 6 | A77782 | 2 | PLUG, expansion, 58 mm OD |
| 7 | 41-1616 | 5 | PLUG, Cup, 1″, Stainless |
| 8 | A77534 | 1 | PLUG, hex, 1/16 inch PT |
| 9 | 217-432 | 1 | PLUG, Hex Soc, 1/4″-18, hex socket headless, 1/4 inch PT, replaces A77428 plug |
| 10 | A77429 | 2 | PLUG, hex socket, 1/2 inch PT |
| 11 | J924148 | 2 | PLUG, hex magnetic, special, 22 mm – 1.5 |
| 12 | J902425 | 2 | WASHER, sealing, plug |
| 13 | J901177 | 24 | KEY, KEEPER – valve |
| 14 | J906412 | 12 | SPRING, VALVE |
| 15 | J912976 | 12 | RETAINER, valve spring |
| 16 | J915707 | 6 | SEAL, intake and exhaust valve stem and guide, used on intake valve only on Emissions Certified |
| 17 | J924492 | 6 | VALVE, ENGINE, INLET, STD |
| 18 | J921444 | 6 | VALVE, ENG EXHAUST, STD |
| 19 | J917728 | 14 | BOLT, BOLT – cylinder head, 160 mm long |
| 19 | J917729 | 12 | SCREW, BOLT – cylinder head, 80 mm long |
| 20 | J931623 | 12 | TAPPET, valve, push rod |
| 21 | J905194 | 12 | ROD, PUSH, rocker arm |
| 22 | J905870 | 6 | SUPPORT, shaft, rocker arm |
| 23 | J901693 | 6 | CLAMP, retaining, shaft |
| 24 | 868-10065 | 12 | SCREW, 12 Pt Hd, M10 x 65, 12.9, BOLT – 12 point flange, 10 – 1.5 x 65 mm, class 12.9 |
| 25 | J919677 | 1 | MANIFOLD, oil, rocker arm |
| 26 | J901717 | 12 | ROCKER, ARM ASSEMBLY, Includes: Ref. 27, 28, 29 |
| 27 | J937438 | 1 | SET SCREW, Hex Skt, 3/8″-24 x 33mm, Adj, Ball Point, slotted set, adjusting, special |
| 28 | 425-116 | 1 | NUT, 3/8″-24, G5 |
| 30 | J919435 | 6 | SHAFT, rocker |
| 31 | J906100 | 12 | CUP, SPRING, WASHER – |
| 32 | J907206 | 12 | WASHER, flat, special |
| 33 | 100-1187 | 12 | RING, SNAP, #87, Ext |
| 1 | J920065 | 1 | CAMSHAFT, Engine, 8950 Tractor only |
| 2 | J917883 | 1 | PIN, dowel, gear, 8950 Tractor only, prior engine number 44903045 , later production uses 126-112 |
| 3 | J927155 | 1 | SUPPORT, thrust, camshaft |
| 4 | J917328 | 1 | GEAR, camshaft, 8930 and 8940 Tractors, no longer available, order J918777 gear below |
| 4 | J918777 | 1 | GEAR, GEAR – camshaft |
| 5 | J900227 | 2 | SCREW, Hex, M8 x 1.25 x 22 |
| 6 | J945329 | 7 | BEARING, CAMSHAFT, camshaft, replaces J901685 bushing |
| 7 | J924471 | 1 | CAMSHAFT, engine, 8930 and 8940 Tractors, no longer available, order J923478 camshaft and |
| 7 | J923478 | 1 | CAMSHAFT, engine, 8930 and 8940 Tractors, replaces J924471 camshaft |
| 8 | 126-112 | 1 | KEY, WOODRUFF, #6, 5/32″ x 5/8″, HT, 8930 and 8940 Tractors, Used with J924471 camshaft and |
| 8 | 836-4065 | 1 | KEY, WOODRUFF, M4 x 6.5 x 15.72, 8930 and 8940 Tractors, Used with J923478 camshaft |
| 1 | J934600 | 1 | ENGINE, SKELETON, BLOCK ASSEMBLY – short, new, includes stripped block, pistons, connecting |
| 2 | J917313 | 7 | CAP, bearing, main |
| 3 | J916369 | 14 | SCREW, Hex Flg Hd, M14 x 128, Bearing cap to block |
| 4 | J945329 | 7 | BEARING, CAMSHAFT, camshaft, see Figure 2-48, item 6, replaces J901685 bushing |
| 5 | A77782 | 1 | PLUG, expansion, 58 mm OD |
| 6 | A77586 | 1 | PLUG, expansion, 43 mm OD |
| 7 | A77506 | 4 | PLUG, expansion, 21 mm OD |
| 8 | J905401 | 4 | PLUG, expansion, 35 mm OD |
| 9 | J920706 | 1 | PLUG, expansion, 22 mm OD |
| 10 | A77530 | 2 | PLUG, expansion, 30 mm OD |
| 11 | 41-3044 | 1 | PLUG, Exp, 2 3/4″ |
| 12 | J901846 | 4 | PIN, dowel |
| 13 | J906619 | 6 | PLUG, hex, 1/8 inch PT |
| 14 | A77429 | 5 | PLUG, hex socket, 1/2 inch PT |
| 15 | A77505 | 2 | PLUG, hex socket, 3/4 inch PT |
| 16 | A77533 | 1 | PLUG, hex socket, 1 inch PT |
| 17 | J928031 | 12 | NOZZLE, piston cooling |
| 18 | J900257 | 2 | PIN, dowel, 16 mm long |
| 19 | 217-103 | 1 | COCK, DRAIN, VALVE – 1/4 inch PT, coolant |
| 20 | J903744 | 1 | FITTING, PIPE, TUBE – turbocharger oil drain |
| 21 | J920762 | 1 | ELBOW, HOSE – 79 mm (3-1/8 inch), water |
| 22 | J918521 | 1 | CLAMP, HOSE, adj, 1-13/16 – 2-3/4 inch dia, coolant |
| 23 | J905408 | 1 | TUBE, oil filler |
| 24 | A77424 | 1 | PLUG, CAP – oil fill tube |
| 25 | J928896 | 1 | TUBE, oil dipstick |
| 26 | J928895 | 1 | DIPSTICK, oil |
| 27 | J926048 | 1 | O-RING, sealing, 66 mm ID |
| 28 | 196466A1 | 1 | CABLE, ELECTRIC, engine block heater |
| 30 | J910517 | 1 | O-RING, heater sealing, engine block heater |
| 31 | L18337 | 1 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch, not shown, engine block heater |
| 1 | J934600 | 1 | ENGINE, SKELETON, BLOCK ASSEMBLY – short, new, includes stripped block, pistons, connecting |
| 2 | J917313 | 7 | CAP, bearing, main |
| 3 | J916369 | 14 | SCREW, Hex Flg Hd, M14 x 128, Bearing cap to block |
| 4 | J945329 | 7 | BEARING, CAMSHAFT, camshaft, see Figure 2-48, item 6, replaces J901685 bushing |
| 5 | A77782 | 1 | PLUG, expansion, 58 mm OD |
| 6 | A77586 | 1 | PLUG, expansion, 43 mm OD |
| 7 | A77506 | 4 | PLUG, expansion, 21 mm OD |
| 8 | J905401 | 4 | PLUG, expansion, 35 mm OD |
| 9 | J920706 | 1 | PLUG, expansion, 22 mm OD |
| 10 | A77530 | 2 | PLUG, expansion, 30 mm OD |
| 11 | 41-3044 | 1 | PLUG, Exp, 2 3/4″ |
| 12 | J901846 | 4 | PIN, dowel |
| 13 | J906619 | 6 | PLUG, hex, 1/8 inch PT |
| 14 | A77429 | 5 | PLUG, hex socket, 1/2 inch PT |
| 15 | A77505 | 2 | PLUG, hex socket, 3/4 inch PT |
| 16 | A77533 | 1 | PLUG, hex socket, 1 inch PT |
| 17 | J928031 | 12 | NOZZLE, piston cooling |
| 18 | J900257 | 2 | PIN, dowel, 16 mm long |
| 19 | 217-103 | 1 | COCK, DRAIN, VALVE – 1/4 inch PT, coolant |
| 20 | J903744 | 1 | FITTING, PIPE, TUBE – turbocharger oil drain |
| 21 | J920762 | 1 | ELBOW, HOSE – 79 mm (3-1/8 inch), water |
| 22 | J918521 | 1 | CLAMP, HOSE, adj, 1-13/16 – 2-3/4 inch dia, coolant |
| 23 | J905408 | 1 | TUBE, oil filler |
| 24 | A77424 | 1 | PLUG, CAP – oil fill tube |
| 25 | J928896 | 1 | TUBE, oil dipstick |
| 26 | J928895 | 1 | DIPSTICK, oil |
| 27 | J926048 | 1 | O-RING, sealing, 66 mm ID |
| 28 | 196466A1 | 1 | CABLE, ELECTRIC, engine block heater |
| 30 | J910517 | 1 | O-RING, engine block heater sealing |
| 31 | L18337 | 1 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch, not shown, engine block heater |
| 1 | J934600 | 1 | ENGINE, SKELETON, BLOCK ASSEMBLY – short, new, includes stripped block, pistons, connecting |
| 2 | J917313 | 7 | CAP, bearing, main |
| 3 | J916369 | 14 | SCREW, Hex Flg Hd, M14 x 128, Bearing cap to block |
| 4 | J945329 | 7 | BEARING, CAMSHAFT, camshaft, see Figure 2-48, item 6, replaces J901685 bushing |
| 5 | A77782 | 1 | PLUG, expansion, 58 mm OD |
| 6 | A77586 | 1 | PLUG, expansion, 43 mm OD |
| 7 | A77506 | 4 | PLUG, expansion, 21 mm OD |
| 8 | J905401 | 4 | PLUG, expansion, 35 mm OD |
| 9 | J920706 | 1 | PLUG, expansion, 22 mm OD |
| 10 | A77530 | 2 | PLUG, expansion, 30 mm OD |
| 11 | 41-3044 | 1 | PLUG, Exp, 2 3/4″ |
| 12 | J901846 | 4 | PIN, dowel |
| 13 | J906619 | 6 | PLUG, hex, 1/8 inch PT |
| 14 | A77429 | 5 | PLUG, hex socket, 1/2 inch PT |
| 15 | A77505 | 2 | PLUG, hex socket, 3/4 inch PT |
| 16 | A77533 | 1 | PLUG, hex socket, 1 inch PT |
| 17 | J928031 | 12 | NOZZLE, piston cooling |
| 18 | J900257 | 2 | PIN, dowel, 16 mm long |
| 19 | 217-103 | 1 | COCK, DRAIN, VALVE – 1/4 inch PT, coolant |
| 20 | J903744 | 1 | FITTING, PIPE, TUBE – turbocharger oil drain |
| 21 | J920762 | 1 | ELBOW, HOSE – 79 mm (3-1/8 inch), water |
| 22 | J918521 | 1 | CLAMP, HOSE, adj, 1-13/16 – 2-3/4 inch dia, coolant |
| 23 | J905408 | 1 | TUBE, oil filler |
| 24 | A77424 | 1 | PLUG, CAP – oil fill tube |
| 25 | J928896 | 1 | TUBE, oil dipstick |
| 26 | J928895 | 1 | DIPSTICK, oil |
| 27 | J926048 | 1 | O-RING, sealing, 66 mm ID |
| 28 | 196466A1 | 1 | CABLE, ELECTRIC, engine block heater |
| 30 | J910517 | 1 | O-RING, heater sealing, engine block |
| 31 | L18337 | 1 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch, not shown, engine block heater |
| 1 | J917443 | 1 | CRANKSHAFT, ASSEMBLY – engine, new, 8930 and 8940 Tractors, no longer available, order |
| 1 | J918986 | 1 | CRANKSHAFT, ASSEMBLY – engine, new, Includes: Ref. 2, 2, 3 |
| 2 | J918380 | 1 | GEAR, crankshaft, 8930 and 8940 Tractors, no longer available, order J918776 gear below |
| 2 | J918776 | 1 | GEAR, crankshaft, steel |
| 3 | J904483 | 1 | PIN, dowel |
| 5 | J925568 | 1 | DAMPER, PULLEY – crankshaft vibration damper |
| 6 | J906733 | 4 | BOLT, hex flange, special, 14 x 35 mm |
| 8 | J921042 | 1 | COVER, REAR, RETAINER – seal |
| 9 | J914301 | 1 | GASKET, rear cover retainer |
| 10 | 845-6015 | 8 | BOLT, Hex Flg, M6 x 15, 8.8, Full Thd |
| 11 | J945930 | 6 | BEARING, CRANKSHAFT, main, upper and lower set, standard, replaces A77711 bearing |
| 11 | J945931 | 6 | BEARING, CRANKSHAFT, main, upper and lower set, 0.25 mm undersize, replaces A77712 bearing |
| 11 | A77713 | 6 | BEARING LINER, main, upper and lower set, 0.50 mm undersize |
| 11 | A77714 | 6 | BEARING LINER, main, upper and lower set, 0.75 mm undersize |
| 11 | A77715 | 6 | BEARING LINER, main, upper and lower set, 1.0 mm undersize |
| 12 | J945929 | 1 | BEARING, CRANKSHAFT, main thrust, upper and lower set, standard, replaces A77843 bearing |
| 12 | J945922 | 1 | BEARING, CRANKSHAFT, main thrust, upper and lower set, 0.25 mm undersize, replaces A77844 |
| 12 | A77845 | 1 | BEARING LINER, main thrust, upper and lower set, 0.50 mm undersize |
| 12 | A77846 | 1 | BEARING LINER, main thrust, upper and lower set, 0.75 mm undersize |
| 12 | A77847 | 1 | BEARING LINER, main thrust, upper and lower set, 1.0 mm undersize |
| 12 | A77848 | 1 | BEARING, CRANKSHAFT, main thrust, upper and lower set, standard journal diameter, 0.25 mm |
| 12 | J945927 | 1 | BEARING, CRANKSHAFT, main thrust, upper and lower set, standard journal diameter, 0.50 mm |
| 12 | A77850 | 1 | BEARING, CRANKSHAFT, main thrust, upper and lower set, 0.50 mm undersize journal diameter |
| 13 | J918113 | 1 | SHIELD, dust, front seal, order item 14, A77790 kit |
| 14 | A77790 | 1 | KIT, SEALS, oil, crankshaft front, Includes: Ref. 15, 16, 17, 18 |
| 18 | J918113 | 1 | SHIELD, dust, front seal |
| 19 | A77808 | 1 | KIT, SERVICE, wear sleeve, crankshaft front, Includes: Ref. 20, 21, 22, 23 |
| 23 | J924987 | 1 | SHIELD, dust |
| 24 | J934486 | 1 | KIT, SERVICE, KIT – oil seal, crankshaft rear, replaces A77809 kit, Includes: Ref. 25, 26 |
| 28 | A77810 | 1 | KIT, SERVICE, KIT – oil, crankshaft rear, includes wear sleeve, Includes: Ref. 29, 32 |
| 1 | J934838 | 1 | FLYWHEEL, ASSEMBLY – engine, replaces J925872 flywheel assembly, Includes: Ref. 2 |
| 2 | J905031 | 1 | GEAR, GEAR – ring, flywheel |
| 3 | J901395 | 8 | SCREW, Hex, M12 x 1.25 x 32, Spc |
| 4 | J900269 | 8 | WASHER, flat, special, retaining |
| 5 | 119491A1 | 1 | HOUSING, flywheel, Includes: Ref. 6 |
| 6 | 375362R1 | 2 | PIN, dowel, 1/2 x 1-3/8 inch |
| 7 | 93141C1 | 1 | PLUG, cup, use without MFD |
| 8 | J910248 | 1 | PLUG, flywheel housing |
| 9 | 238-5212 | 1 | O-RING, -212, 70 Duro, .859″ ID x .139″ Thk |
| 10 | 828-16060 | 1 | BOLT, Hex, M16 x 60, 10.9, Full Thd, Flywheel housing to top of clutch housing |
| 10 | 628-16050 | 1 | BOLT, Hex, M16 x 50, 10.9, Full Thd, Flywheel housing to top of clutch housing |
| 10 | 828-12050 | 2 | BOLT, Hex, M12 x 50, 10.9, Flywheel housing to bottom of clutch housing |
| 10 | 628-22065 | 2 | BOLT, Hex, M22 x 65, 10.9, Full Thd, BOLT – hex, full threads, 22 – 2.5 x 65 mm, class 10.9, flywheel |
| 10 | 828-20070 | 2 | BOLT, Hex, M20 x 70, 10.9, Full Thd, Flywheel housing to center of side channel |
| 10 | 827-12065 | 2 | BOLT, Hex, M12 x 65, 10.9, hex, 12 – 1.75 x 65 mm, class 10.9, speed housing to top of flywheel |
| 11 | A157918 | 10 | WASHER, flat, 12 mm, flywheel housing into engine |
| 11 | 896-16016 | 3 | WASHER, M16 x 34.5 x 5, HT, flat, 17.5 x 34 x 5 mm, hardened, flywheel housing to top of clutch |
| 11 | 896-15012 | 2 | WASHER, M12 x 28.5 x 4, HT, flat, 13.5 x 28 x 4 mm, hardened, speed housing to top of flywheel |
| 11 | 1289123C1 | 2 | WASHER, flat, 22 mm, flywheel housing to side of clutch housing |
| 11 | A177650 | 2 | WASHER, flat, flywheel housing to center of side channel |
| 11 | 896-15012 | 2 | WASHER, M12 x 28.5 x 4, HT, flat, 13.5 x 28 x 4 mm, hardened, speed housing to top of flywheel |
| 12 | 892-11012 | 2 | WASHER, LOCK, M12, Flywheel Housing into Engine |
| 13 | 896-16012 | 4 | WASHER, M12 x 28.5 x 4, HT, flat, 13.5 x 28 x 4 mm, hardened |
| 14 | 92590C2 | 1 | PLATE, drive |
| 15 | 614-12025 | 6 | BOLT, Hex, M12 x 25, 8.8, Full threads |
| 16 | 896-11012 | 6 | WASHER, M13.5 x 24.5 x 3, HT |
| 17 | 615-12040 | 2 | BOLT, Hex, M12 x 40, 8.8, Full Thd, BOLT – hex, full threads, 12 – 1.75 x 40 mm, plug hole without MFD |
| 18 | 832-10412 | 2 | NUT, LOCK, M12 x 1.75, Cl 8, Plug hole without MFD |
| 1 | J919937 | 1 | SLEEVE CYLINDER, piston |
| 2 | J907177 | 1 | O-RING, sealing, cylinder sleeve, piston |
| 4 | 100-21175 | 2 | RING, SNAP, 1.75″, Int, #175 |
| 5 | A77802 | 1 | RING SET, PISTON, KIT – piston ring, Includes: Ref. 6, 7, 8 |
| 2 | J907177 | 1 | O-RING, sealing, piston |
| 4 | 100-21175 | 2 | RING, SNAP, 1.75″, Int, #175 |
| 5 | J802429 | 1 | KIT, PISTON RINGS, Includes: Ref. 6, 7, 8 |
| 9 | J901597 | 6 | PIN, piston |
| 11 | J913990 | 1 | BUSHING, connecting rod |
| 12 | J928870 | 2 | BOLT, BOLT – special, rod, bearing cap, connecting rod |
| 13 | J934864 | 2 | NUT, hex, rod bolt, replaces J901381 nut, connecting rod |
| 14 | A77563 | 6 | BEARING LINER, KIT – upper and lower, standard, connecting rod |
| 14 | A77564 | 6 | BEARING LINER, KIT – upper and lower, 0.25 mm undersize, connecting rod |
| 14 | A77565 | 6 | BEARING LINER, KIT – upper and lower, 0.50 mm undersize, connecting rod |
| 14 | A77566 | 6 | BEARING LINER, KIT – upper and lower, 0.75 mm undersize, connecting rod |
| 14 | A77567 | 6 | BEARING LINER, KIT – upper and lower, 1.00 mm undersize, connecting rod |
| 1 | A77854 | 6 | PACKAGE, REPAIR, KIT – piston and sleeve, engine, see Figure 2-68, prior to engine serial number |
| 2 | A77563 | 6 | BEARING LINER, KIT – upper and lower, standard, see Figure 2-68, prior to engine serial number |
| 3 | J901597 | 6 | PIN, piston, see Figure 2-68, prior to engine serial number 45636466 |
| 4 | A77711 | 6 | BEARING LINER, main, upper and lower set, standard, see Figure 2-62, prior to engine serial number |
| 5 | A77842 | 1 | KIT, GASKET, valve grind, see Figure 2-70, prior to engine serial number 45636466 |
| 6 | J935585 | 1 | GASKET, cylinder head, standard, see Figure 2-40, prior to engine serial number 45636466 |
| 7 | A77679 | 1 | KIT, GASKET, oil pan, see Figure 2-38, prior to engine serial number 45636466 |
| 2 | A77563 | 6 | BEARING LINER, KIT – upper and lower, standard, see Figure 2-68, engine serial number 45636466 |
| 3 | J901597 | 6 | PIN, piston, see Figure 2-68, engine serial number 45636466 and after |
| 4 | A77711 | 6 | BEARING LINER, main, upper and lower set, standard, see Figure 2-62, engine serial number |
| 5 | A77842 | 1 | KIT, GASKET, valve grind, see Figure 2-70, engine serial number 45636466 and after |
| 6 | J935585 | 1 | GASKET, cylinder head, standard, see Figure 2-40, engine serial number 45636466 and after |
| 7 | A77679 | 1 | KIT, GASKET, oil pan, see Figure 2-38, engine serial number 45636466 and after |
| 1 | J914310 | 1 | GASKET, thermostat housing |
| 2 | J918779 | 1 | GASKET, outlet tube, water |
| 3 | J915707 | 6 | SEAL, intake and exhaust valve stem and guide, used on intake valve only on Emissions Certified |
| 4 | J911941 | 1 | GASKET, mounting, turbocharger |
| 5 | J929012 | 6 | GASKET, exhaust manifold, 0.54 mm thick |
| 6 | J914311 | 1 | GASKET, intake manifold cover |
| 7 | J931350 | 1 | GASKET, turbo oil drain tube, replaces J928919 gasket |
| 8 | J942725 | 1 | GASKET, turbo oil drain, replaces J819378 gasket |
| 9 | J905449 | 1 | SEAL, RUBBER, valve cover |
| 10 | J910824 | 6 | O-RING, cover bolt |
| 11 | J909886 | 6 | SEAL, SLEEVE – injector |
| 12 | J903380 | 7 | SEAL, connector, fuel injection nozzle |
| 13 | 238-5115 | 1 | O-RING, -115, 70 Duro, .674″ ID x .103″ Thk, Connector to valve cover |
| 14 | J923261 | 6 | WASHER, SEAL – injector nozzle, 2.5 mm thick, 7 mm injector tip |
| 15 | 238-5111 | 1 | O-RING, -111, 70 Duro, .424″ ID x .103″ Thk, Water filter shutoff valve |
| 16 | J930827 | 1 | HOSE, 51 mm (2 inch) long, breather tube to connector, replaces J918610 hose |
| 17 | J919677 | 1 | MANIFOLD, oil, rocker arm |
| 18 | J914708 | 12 | PLATE, LOCKING, exhaust manifold bolt |
| 19 | J823921 | 1 | GAUGE, cylinder head, bolt length |
| 1 | J903475 | 1 | SEAL, front access cover |
| 2 | J929253 | 1 | GASKET, housing, gear |
| 3 | J915772 | 1 | SEALRING, RING – quad, timing pin housing |
| 4 | J931608 | 1 | GASKET, access cover plate, replaces J919601 gasket |
| 5 | J902089 | 1 | SEAL, sealing, water pump |
| 6 | J914301 | 1 | GASKET, rear cover retainer, crankshaft |
| 7 | J918174 | 1 | GASKET, cooler core, oil |
| 8 | J929011 | 1 | GASKET, cooler cover, oil |
| 9 | J901798 | 1 | WASHER, SEALING, WASHER – sealing |
| 10 | J931059 | 1 | GASKET, mounting, fuel transfer pump, replaces J923054 gasket |
| 11 | J912473 | 1 | SEALRING, flywheel housing to block |
| 12 | 238-5212 | 1 | O-RING, -212, 70 Duro, .859″ ID x .139″ Thk |
| 13 | J907177 | 6 | O-RING, sealing, sleeve |
| 14 | J913994 | 1 | O-RING, sealing |
| 15 | J916284 | 1 | O-RING, O-RING – fuel injection pump |
| 16 | J926722 | 1 | SEAL, RING – quad, fuel injection pump |
| 17 | J931351 | 1 | GASKET, gear housing |
| 1 | J926882 | 1 | PUMP, FUEL INJECTION, ASSEMBLY – fuel, with aneroid, parts list Figure 3-18 |
| 2 | J930525 | 6 | INJECTOR ASSY., fuel, parts list Figure 3-24 |
| 3 | J909886 | 6 | SEAL, SLEEVE – injector, sealing |
| 4 | J910279 | 6 | CLAMP, fuel injector |
| 5 | 845-8080 | 6 | BOLT, Hex Flg, M8 x 80, 8.8, BOLT – heavy hex flange, 8 – 1.25 x 80 mm, replaces J922018 bolt |
| 6 | J930442 | 1 | PIPE INJECTION, TUBE – fuel injector, No. 1 cylinder |
| 7 | J930443 | 1 | PIPE INJECTION, TUBE – fuel injector, No. 2 cylinder |
| 8 | J930444 | 1 | PIPE INJECTION, TUBE – fuel injector, No. 3 cylinder |
| 9 | J917716 | 1 | BRACE, BRACKET – fuel tube, supply |
| 11 | J920854 | 5 | SCREW, Hex Hd, M5 x .8 x 20, w/LW |
| 12 | J904519 | 3 | SUPPORT, tube retaining |
| 13 | J917747 | 6 | CLAMP, fuel tube |
| 14 | J917776 | 2 | BRACE, BRACE – fuel tube |
| 16 | J920855 | 2 | BOLT, hex, captive washer, special, 5 – 0.8 x 35 mm |
| 17 | J917717 | 1 | BRACE, BRACKET – fuel tube |
| 18 | J917746 | 2 | CLAMP, fuel tube |
| 19 | J904711 | 1 | CLAMP, BRACKET – fuel tube |
| 20 | J930445 | 1 | PIPE INJECTION, TUBE – fuel injector, No. 4 cylinder |
| 21 | J930446 | 1 | PIPE INJECTION, TUBE – fuel injector, No. 5 cylinder |
| 22 | J930447 | 1 | PIPE INJECTION, TUBE – fuel injector, No. 6 cylinder |
| 24 | J903380 | 6 | SEAL, connector |
| 25 | J905307 | 6 | BOLT, BANJO, M6 x 1 x 14.3, BOLT – banjo drain, special |
| 26 | J920595 | 1 | TUBE ASSY., fuel drain |
| 27 | J924726 | 1 | BOLT, BANJO, check |
| 28 | J918188 | 2 | WASHER, sealing, banjo fitting |
| 29 | J916779 | 1 | HOSE, FLEXIBLE, 508 mm (20 inch) long, cylinder block to injection pump |
| 30 | 222-762 | 1 | ELBOW, 90є, 7/16″-20, 45є Fl x 1/8″ NPT, 90 degree, 7/16-20 45 degree flare x 1/8 inch PT |
| 31 | J918002 | 1 | BOLT, BANJO, banjo, hose to injection pump |
| 32 | J918190 | 2 | WASHER, SEALING, WASHER – sealing, special, 10 x 15.5 x 1 mm |
| 1 | J926885 | 1 | PUMP, FUEL INJECTION, ASSEMBLY – fuel, new, parts list Figure 3-20, no longer available, order |
| 1 | J935106 | 1 | PUMP, FUEL INJECTION, ASSEMBLY – fuel, new, parts list Figure 3-20 |
| 2 | J930525 | 6 | INJECTOR ASSY., fuel, parts list Figure 3-24 |
| 3 | J909886 | 6 | SEAL, SLEEVE – injector, sealing |
| 4 | J910279 | 6 | CLAMP, fuel injector |
| 5 | 845-8080 | 6 | BOLT, Hex Flg, M8 x 80, 8.8, BOLT – heavy hex flange, 8 – 1.25 x 80 mm, repalces J922018 bolt |
| 6 | J930355 | 1 | PIPE INJECTION, TUBE – fuel injector, No. 1 cylinder, if used |
| 7 | J930356 | 1 | PIPE INJECTION, TUBE – fuel injector, No. 2 cylinder, if used |
| 8 | J930357 | 1 | PIPE INJECTION, TUBE – fuel injector, No. 3 cylinder, if used |
| 9 | J917716 | 3 | BRACE, BRACKET – fuel tube, supply |
| 11 | J920854 | 10 | SCREW, Hex Hd, M5 x .8 x 20, w/LW |
| 12 | J904519 | 5 | SUPPORT, tube retaining |
| 13 | J917747 | 10 | CLAMP, fuel tube |
| 14 | J917776 | 1 | BRACE, BRACKET – fuel tube |
| 16 | J920855 | 2 | BOLT, hex, captive washer, special, 5 – 0.8 x 35 mm |
| 17 | J917717 | 2 | BRACE, BRACKET – fuel tube |
| 18 | J917746 | 4 | CLAMP, fuel tube |
| 19 | J904711 | 2 | CLAMP, BRACKET – fuel tube |
| 20 | J930358 | 1 | PIPE INJECTION, TUBE – fuel injector, No. 4 cylinder, if used |
| 21 | J930359 | 1 | PIPE INJECTION, TUBE – fuel injector, No. 5 cylinder, if used |
| 22 | J930360 | 1 | PIPE INJECTION, TUBE – fuel injector, No. 6 cylinder, if used |
| 24 | J903380 | 6 | SEAL, connector |
| 25 | J905307 | 6 | BOLT, BANJO, M6 x 1 x 14.3, BOLT – banjo drain, special |
| 26 | J920595 | 1 | TUBE ASSY., fuel drain |
| 27 | J924726 | 1 | BOLT, BANJO, check |
| 28 | J918188 | 2 | WASHER, sealing, banjo fitting |
| 29 | J916779 | 1 | HOSE, FLEXIBLE, 508 mm (20 inch) long, cylinder block to injection pump |
| 30 | 222-762 | 1 | ELBOW, 90є, 7/16″-20, 45є Fl x 1/8″ NPT, 90 degree, 7/16-20 45 degree flare x 1/8 inch PT |
| 31 | J918002 | 1 | BOLT, BANJO, banjo, hose to injection pump |
| 32 | J918190 | 2 | WASHER, SEALING, WASHER – sealing, special, 10 x 15.5 x 1 mm |
| 33 | 895-11005 | 12 | WASHER, M5 x 10 x 1, If used, Not shown |
| 1 | J926776 | 1 | PUMP, FUEL INJECTION, ASSEMBLY – fuel, new, component parts not serviced separately, see |
| 2 | J926787 | 6 | INJECTOR ASSY., fuel, parts list Figure 3-24 |
| 3 | J909886 | 6 | SEAL, SLEEVE – injector, sealing |
| 4 | J910279 | 6 | CLAMP, fuel injector |
| 5 | J922018 | 6 | SCREW, BOLT – heavy hex flange, 8 – 1.25 x 80 mm, class 12.9 |
| 6 | J929801 | 1 | PIPE INJECTION, TUBE – fuel injector, No. 1 cylinder |
| 7 | J929802 | 1 | PIPE INJECTION, TUBE – fuel injector, No. 2 cylinder |
| 8 | J929803 | 1 | PIPE INJECTION, TUBE – fuel injector, No. 3 cylinder |
| 9 | J917716 | 3 | BRACE, BRACKET – fuel tube, supply |
| 11 | J920854 | 10 | SCREW, Hex Hd, M5 x .8 x 20, w/LW |
| 12 | J904519 | 5 | SUPPORT, tube retaining |
| 13 | J917747 | 10 | CLAMP, fuel tube |
| 14 | J917776 | 1 | BRACE, BRACKET – fuel tube |
| 15 | J920855 | 2 | BOLT, hex, captive washer, special, 5 – 0.8 x 35 mm |
| 16 | J910686 | 1 | BRACE, tube retaining |
| 17 | J917748 | 1 | CLAMP, fuel tube |
| 18 | J917740 | 1 | BRACE, tube retaining |
| 19 | J917749 | 2 | CLAMP, tube |
| 20 | J929804 | 1 | PIPE INJECTION, TUBE – fuel injector, No. 4 cylinder |
| 21 | J929805 | 1 | PIPE INJECTION, TUBE – fuel injector, No. 5 cylinder |
| 22 | J929806 | 1 | PIPE INJECTION, TUBE – fuel injector, No. 6 cylinder |
| 24 | J903380 | 6 | SEAL, connector |
| 25 | J905307 | 7 | BOLT, BANJO, M6 x 1 x 14.3, BOLT – banjo drain, special |
| 26 | J920595 | 1 | TUBE ASSY., fuel drain |
| 27 | J924726 | 1 | BOLT, BANJO, check |
| 28 | J918188 | 2 | WASHER, sealing, banjo fitting |
| 29 | J917717 | 1 | BRACE, BRACKET – fuel tube |
| 30 | J917746 | 2 | CLAMP, fuel tube |
| 31 | J904711 | 1 | CLAMP, BRACKET – fuel tube |
| 32 | J921416 | 1 | HOLDER, BRACE – tube |
| 33 | J918786 | 2 | FIXING BRACKET, CLAMP – vibration |
| 34 | J918785 | 1 | BRACE, tube |
| 1 | J908110 | 1 | PLUG, threaded |
| 2 | 86637724 | 1 | PLUG, Hex Soc, 1/8″-27 NPTF, hex, socket headless, 1/8 inch PT, replaces J906619 plug |
| 3 | J921594 | 1 | PLUG, threaded orifice, cylinder head to tee |
| 4 | J902425 | 2 | WASHER, sealing, plug |
| 5 | 217-1061 | 1 | TEE, 1/8″-27 Female x 1/8″-27 Male Run, street, 1/8 inch female PT branch x female PT x PT |
| 6 | 222-41 | 1 | ELBOW, 90є, 7/16″-24 x 1/8 NPT, ELBOW – 90 degree, compression, 3/16 tube OD x 1/8 inch PT, tee |
| 6 | 222-21 | 1 | FITTING, 7/16″-24 x 1/8″ NPTF, Tee to aneroid tube, if used |
| 7 | J926739 | 1 | TUBE, aneroid, nylon |
| 8 | J903035 | 1 | BOLT, BANJO, hex, 12 – 1.5 x 24 mm |
| 9 | J919644 | 1 | FITTING, CONNECTOR – banjo |
| 10 | J935171 | 2 | WASHER, SEALING, special, 12 x 19 x 1.5 mm, replaces J918191 washer |
| 11 | A77796 | 1 | CONNECTOR, ADAPTER – straight, 1/4 barb end x 1/8 inch PT, tee to wastegate tube |
| 12 | J926969 | 1 | TUBE, wastegate |
| 13 | 222-102 | 1 | SLEEVE, 1/4″ Tube |
| 14 | 825-2410 | 1 | NUT, M10 x 1.5, Flg, Cl 8, Wastegate tube to valve cover, if used |
| 14 | 825-2408 | 1 | NUT, M8 x 1.25, Flg, Cl 8, Wastegate tube to valve cover, if used |
| 15 | J920871 | 1 | HOSE, 1294 mm (51 inch) long |
| 16 | 214-1404 | 2 | CLAMP, HOSE, #4, 0.25/0.62 Type M Worm, Adj |
| 17 | J926882 | 1 | PUMP, FUEL INJECTION, ASSEMBLY – fuel, with aneroid, parts list Figure 3-18 |
| 18 | J535106 | 1 | ACTUATOR, turbo wastegate, see Figure 2-34 for actuator and component parts |
| 1 | J908110 | 1 | PLUG, threaded |
| 2 | 86637724 | 1 | PLUG, Hex Soc, 1/8″-27 NPTF, hex socket headless, 1/8 inch PT, replaces J906619 plug |
| 3 | J921594 | 1 | PLUG, threaded orifice, cylinder head to tee |
| 4 | J902425 | 2 | WASHER, sealing, plug |
| 5 | 217-1061 | 1 | TEE, 1/8″-27 Female x 1/8″-27 Male Run, street, 1/8 inch female PT branch x female PT x PT |
| 6 | 222-41 | 1 | ELBOW, 90є, 7/16″-24 x 1/8 NPT, ELBOW – 90 degree, compression, 3/16 tube OD x 1/8 inch PT, tee |
| 6 | 222-21 | 1 | FITTING, 7/16″-24 x 1/8″ NPTF, Tee to aneroid tube, if used |
| 7 | J926739 | 1 | TUBE, aneroid, nylon |
| 8 | J903035 | 1 | BOLT, BANJO, hex, 12 – 1.5 x 24 mm |
| 9 | J919644 | 1 | FITTING, CONNECTOR – banjo |
| 10 | J935171 | 2 | WASHER, SEALING, special, 12 x 19 x 1.5 mm, replaces J918191 washer |
| 11 | A77796 | 1 | CONNECTOR, ADAPTER – straight, 1/4 barb end x 1/8 inch PT, tee to wastegate tube |
| 12 | J922640 | 1 | PIPE, TUBE – wastegate |
| 13 | 222-102 | 1 | SLEEVE, 1/4″ Tube |
| 14 | 825-2410 | 1 | NUT, M10 x 1.5, Flg, Cl 8, Wastegate tube to valve cover, if used |
| 14 | 825-2408 | 1 | NUT, M8 x 1.25, Flg, Cl 8, Wastegate tube to valve cover, if used |
| 15 | J920871 | 1 | HOSE, 1294 mm (51 inch) long |
| 16 | 214-1404 | 2 | CLAMP, HOSE, #4, 0.25/0.62 Type M Worm, Adj |
| 17 | J935106 | 1 | PUMP, FUEL INJECTION, ASSEMBLY – fuel, new, parts list Figure 3-20, repalces J927129 pump |
| 18 | J531892 | 1 | ACTUATOR, turbo wastegate, see Figure 2-34 for actuator and component parts |
| 1 | J908110 | 1 | PLUG, threaded, if used |
| 2 | J906619 | 1 | PLUG, hex, 1/8 inch PT, if used |
| 3 | 222-41 | 1 | ELBOW, 90є, 7/16″-24 x 1/8 NPT, ELBOW – 90 degree, compression, 3/16 tube OD x 1/8 inch PT, if |
| 5 | 217-1061 | 1 | TEE, 1/8″-27 Female x 1/8″-27 Male Run, street, 1/8 inch female PT branch x female PT x PT, if used |
| 6 | 222-41 | 1 | ELBOW, 90є, 7/16″-24 x 1/8 NPT, ELBOW – 90 degree, compression, 3/16 tube OD x 1/8 inch PT, if |
| 7 | J926739 | 1 | TUBE, aneroid, nylon, if used |
| 8 | 222-21 | 1 | FITTING, 7/16″-24 x 1/8″ NPTF, Aneroid tube to tee |
| 9 | 222-21 | 1 | FITTING, 7/16″-24 x 1/8″ NPTF, Aneroid to aneroid, if used |
| 10 | J920871 | 1 | HOSE, 1294 mm (51 inch) long, if used |
| 11 | 217-120 | 1 | ELBOW, 1/4″ Hose x 1/8″ NPTF, Barbed, ADAPTER – straight, 1/4 barb end x 1/8 inch PT, if used |
| 12 | J929748 | 1 | TUBE, wastegate |
| 14 | J900589 | 1 | NUT, hex flange, special, 8 mm, aneroid tube to cover mounting stud |
| 15 | J920199 | 1 | HOSE |
| 16 | 214-1404 | 4 | CLAMP, HOSE, #4, 0.25/0.62 Type M Worm, Adj |
| 17 | J926776 | 1 | PUMP, FUEL INJECTION, ASSEMBLY – fuel, new, components parts not serviced separately |
| 18 | J531892 | 1 | ACTUATOR, turbo wastegate, see Figure 2-34 for actuator and component parts |
| 1 | J897331 | 1 | SUPPORT, HEAD – fuel filter |
| 3 | J906694 | 1 | SEALRING, sealing, 70 mm ID, filter head |
| 4 | J906695 | 1 | SEALRING, sealing, 14 mm ID, adapter |
| 5 | J903293 | 1 | NUT, hex, special, 16 mm – 2.0 |
| 6 | J925955 | 1 | ADAPTER, fuel filter |
| 7 | J930942 | 1 | FILTER, FUEL, Primary, Replaces J925274 filter |
| 8 | J903640 | 1 | FILTER, FUEL, secondary |
| 9 | J918873 | 1 | TUBE, supply, fuel |
| 10 | J914711 | 1 | CLIP, CLAMP – P-type |
| 11 | J935171 | 2 | WASHER, SEALING, special, 12 x 19 x 1.5 mm, replaces J918191 washer |
| 12 | J911446 | 1 | BOLT, BANJO, M12 x 1.5 x 24 |
| 13 | J905403 | 1 | SCREW, hex, special, vent |
| 14 | J918192 | 4 | RING, PACKING, WASHER – sealing, special, 14 x 20 x 1 mm |
| 15 | J924725 | 1 | BOLT, BANJO, connector |
| 16 | J936316 | 1 | PUMP, FUEL, lift, fuel, repair kit J926764, item 24, is no longer available, replaces J925709 pump |
| 17 | J931059 | 1 | GASKET, mounting, fuel transfer pump, replaces J923054 gasket |
| 18 | 844-8020 | 2 | BOLT, Hex Flg, M8 x 20, 8.8 |
| 19 | J918537 | 1 | TUBE, supply, used with items 32, 33 and 34, if used |
| 20 | J935171 | 2 | WASHER, SEALING, special, 12 x 19 x 1.5 mm, replaces J918191 washer |
| 21 | J916361 | 1 | BOLT, BANJO, banjo connector, 12 – 1.5 x 24 mm |
| 22 | J911447 | 1 | CONNECTOR, banjo, fuel return |
| 23 | J912886 | 1 | VALVE, overflow, see item 6, Figure 3-18 or item 6, Figure 3-20 |
| 24 | J926764 | 1 | KIT, GASKET, transfer pump repair, not shown, no longer available, order complete pump J936316 |
| 30 | J923054 | 2 | GASKET, mounting, fuel transfer pump |
| 32 | J914037 | 1 | JACK SCREW, banjo connector, if used |
| 33 | 217-432 | 1 | PLUG, Hex Soc, 1/4″-18, hex socket headless, 1/4 inch PT, if used |
| 34 | J918192 | 2 | RING, PACKING, WASHER – sealing, special, 14 x 20 x 1 mm, if used |
| 1 | J897331 | 1 | SUPPORT, HEAD – fuel filter |
| 2 | J906694 | 1 | SEALRING, sealing, 70 mm ID, filter head |
| 3 | J906695 | 1 | SEALRING, sealing, 14 mm ID, adapter |
| 4 | J903293 | 1 | NUT, hex, special, 16 mm – 2.0 |
| 5 | J925955 | 1 | ADAPTER, fuel filter |
| 6 | J930942 | 1 | FILTER, FUEL, Primary, Replaces J925274 filter |
| 7 | J903640 | 1 | FILTER, FUEL, secondary |
| 8 | J932568 | 1 | TUBE, supply, fuel, replaces J930405 tube |
| 9 | J914711 | 1 | CLIP, CLAMP – P-type |
| 10 | J935171 | 2 | WASHER, SEALING, special, 12 x 19 x 1.5 mm, replaces J918191 washer |
| 11 | J911446 | 1 | BOLT, BANJO, M12 x 1.5 x 24 |
| 12 | J905860 | 1 | SCREW, BOLT ASSEMBLY – banjo hex, special |
| 13 | J935172 | 4 | WASHER, sealing, special, 14 x 20 x 1 mm, replaces J918192 washer |
| 14 | J924725 | 1 | BOLT, BANJO, connector |
| 15 | J925709 | 1 | PUMP, fuel transfer, repair kit J926764, item 23, is no longer available |
| 16 | J923054 | 1 | GASKET, mounting, fuel transfer pump |
| 17 | 844-8020 | 2 | BOLT, Hex Flg, M8 x 20, 8.8 |
| 18 | J918537 | 1 | TUBE, supply, used with items 32, 33 and 34, if used |
| 19 | J918191 | 2 | RING, PACKING, WASHER – sealing, special, 12 x 18 x 1 mm |
| 20 | J916361 | 1 | BOLT, BANJO, banjo connector, 12 – 1.5 x 24 mm |
| 21 | J911447 | 1 | CONNECTOR, banjo, fuel return |
| 22 | J912886 | 1 | VALVE, overflow |
| 23 | J926764 | 1 | KIT, GASKET, transfer pump repair, not shown, no longer available, order complete pump J925709 |
| 29 | J923054 | 2 | GASKET, mounting, fuel transfer pump |
| 32 | J914037 | 1 | JACK SCREW, banjo connector, if used |
| 33 | 217-432 | 1 | PLUG, Hex Soc, 1/4″-18, hex socket headless, 1/4 inch PT, if used |
| 34 | J918192 | 2 | RING, PACKING, WASHER – sealing, special, 14 x 20 x 1 mm, if used |
| 1 | J926882 | 1 | PUMP, FUEL INJECTION, ASSEMBLY – fuel, with aneroid, Includes: Ref. 2-23 |
| 2 | A77720 | 1 | PIN, timing |
| 3 | 3051337R1 | 1 | WASHER, SEALING, M18 x 24 x 1.5, WASHER – sealing, plug |
| 4 | J912888 | 1 | PLUG, timing |
| 5 | J935032 | 1 | SEAL, GASKET – replaces J930993 O-ring |
| 6 | J912886 | 1 | VALVE, overflow |
| 7 | J935172 | 2 | WASHER, sealing, special, 14 x 20 x 1 mm, replaces 933697R1 washer |
| 8 | J929322 | 1 | LEVER, pump shutoff, not shown |
| 9 | J930683 | 1 | NUT, LOCK, hex, 5 mm – 0.8, not shown |
| 10 | 691292C1 | 1 | RETAINER, HOUSING – spring return |
| 11 | 680187C1 | 1 | O-RING, sealing, special |
| 12 | 1808728C1 | 1 | LEVER, throttle control |
| 13 | J913320 | 1 | SCREW, vent |
| 14 | 691273C1 | 1 | GASKET, vent screw |
| 15 | J912897 | 1 | WASHER, lock |
| 16 | J912896 | 1 | NUT, hex, self-locking, special |
| 18 | B41211 | 1 | SCREW, vent |
| 19 | 933696R1 | 1 | WASHER, SEALING, M6 x 10 x 1, 6 x 10 mm, vent screw |
| 20 | 1808822C1 | 1 | THUMB SCREW, M6 x 26, BOLT – throttle lever |
| 21 | 895-11006 | 1 | WASHER, M6 |
| 22 | 892-11006 | 1 | WASHER, LOCK, M6 |
| 23 | 829-1306 | 1 | NUT, M6, Cl 10 |
| 24 | J931379 | 1 | GEAR, fuel pump, replaces J912615 gear |
| 25 | J916284 | 1 | O-RING, O-RING – |
| 26 | J915036 | 4 | STUD, pump mounting, gear housing to injection pump |
| 27 | 825-2410 | 4 | NUT, M10 x 1.5, Flg, Cl 8 |
| 28 | 97006C1 | 2 | BOLT, BOLT – hex flange, special, 6 – 1 x 20 mm |
| 29 | J923255 | 1 | SUPPORT, BRACKET – solenoid mounting |
| 30 | 844-10020 | 2 | BOLT, Hex Flg, M10 x 20, 8.8 |
| 31 | J930233 | 1 | SOLENOID, fuel shutoff, 12 volt, Includes: Ref. 32-37 |
| 32 | L53928 | 1 | EYE, JOINT – ball, replaces A146456 |
| 33 | 492-11025 | 1 | WASHER, LOCK, 1/4″ |
| 34 | 425-154 | 1 | NUT, Jam, 1/4″-28, G5 |
| 35 | J925171 | 1 | BOOT, protective, plunger |
| 36 | 473321C1 | 1 | STRAP, CABLE, .098″ x 8″, tie |
| 37 | J923887 | 1 | SPRING, return, plunger |
| 38 | J930842 | 1 | HOSE, 330 mm (13 inch) long, fuel drain, replaces J918176 hose |
| 39 | J923527 | 1 | CLAMP, band, hose, replaces A171099 clamp |
| 1 | J935106 | 1 | PUMP, FUEL INJECTION, ASSEMBLY – fuel, new, Includes: Ref. 2-23 |
| 2 | A77720 | 1 | PIN, timing |
| 3 | 3051337R1 | 1 | WASHER, SEALING, M18 x 24 x 1.5, WASHER – sealing, plug |
| 4 | J912888 | 1 | PLUG, timing |
| 5 | J935032 | 1 | SEAL, O-RING – replaces A41856 O-ring |
| 6 | J912886 | 1 | VALVE, overflow |
| 7 | J935172 | 2 | WASHER, sealing, special, 14 x 20 x 1 mm, replaces 933697R1 washer |
| 8 | J929322 | 1 | LEVER, pump shutoff, not shown |
| 9 | J930683 | 1 | NUT, LOCK, hex, 5 mm – 0.8, not shown |
| 10 | 691292C1 | 1 | RETAINER, HOUSING – spring return |
| 11 | 680187C1 | 1 | O-RING, sealing, special |
| 12 | 1808728C1 | 1 | LEVER, throttle control |
| 13 | J913320 | 1 | SCREW, vent |
| 14 | 691273C1 | 1 | GASKET, vent screw |
| 15 | J912897 | 1 | WASHER, lock |
| 16 | J912896 | 1 | NUT, hex, self-locking, special |
| 18 | B41211 | 1 | SCREW, vent |
| 19 | 933696R1 | 1 | WASHER, SEALING, M6 x 10 x 1, 6 x 10 mm, vent screw |
| 20 | 1808822C1 | 1 | THUMB SCREW, M6 x 26, BOLT – throttle lever |
| 21 | 895-11006 | 1 | WASHER, M6 |
| 22 | 892-11006 | 1 | WASHER, LOCK, M6 |
| 23 | 829-1306 | 1 | NUT, M6, Cl 10 |
| 24 | J931379 | 1 | GEAR, fuel pump, replaces J912615 gear |
| 25 | J916284 | 1 | O-RING, O-RING – |
| 26 | J915036 | 4 | STUD, pump mounting, gear housing to injection pump |
| 27 | 825-2410 | 4 | NUT, M10 x 1.5, Flg, Cl 8 |
| 28 | 97006C1 | 2 | BOLT, BOLT – hex flange, special, 6 – 1 x 20 mm |
| 29 | J923255 | 1 | SUPPORT, BRACKET – solenoid mounting |
| 30 | 844-10020 | 2 | BOLT, Hex Flg, M10 x 20, 8.8 |
| 31 | J930233 | 1 | SOLENOID, fuel shutoff, 12 volt, Includes: Ref. 32-37 |
| 32 | L53928 | 1 | EYE, JOINT – ball, replaces A146456 joint |
| 33 | 492-11025 | 1 | WASHER, LOCK, 1/4″ |
| 34 | 425-154 | 1 | NUT, Jam, 1/4″-28, G5 |
| 35 | J925171 | 1 | BOOT, protective, plunger |
| 36 | 473321C1 | 1 | STRAP, CABLE, .098″ x 8″, tie |
| 37 | J923887 | 1 | SPRING, return, plunger |
| 38 | J930842 | 1 | HOSE, 330 mm (13 inch) long, fuel drain, replaces J918176 |
| 39 | J923527 | 1 | CLAMP, band, hose, replaces A171099 clamp |
| 1 | J926776 | 1 | PUMP, FUEL INJECTION, ASSEMBLY – fuel, new, component parts not serviced separately |
| 2 | J931380 | 1 | GEAR, fuel pump, replaces J923578 gear |
| 3 | J926722 | 1 | SEAL, RING – quad, fuel injection pump |
| 4 | J915036 | 4 | STUD, pump mounting |
| 5 | 825-2410 | 4 | NUT, M10 x 1.5, Flg, Cl 8 |
| 6 | J930841 | 1 | SUPPORT, injection pump, injection pump to cylinder block, replaces J930597 support |
| 7 | 844-10020 | 4 | BOLT, Hex Flg, M10 x 20, 8.8, Support to block |
| 8 | J930382 | 1 | HOLDER, BRACKET – fuel pump |
| 9 | J926273 | 1 | SUPPORT, SUPPORT – injection pump, lower |
| 10 | 845-8090 | 2 | BOLT, Hex Flg, M8 x 90, 8.8, Injection pump to lower support |
| 11 | J930383 | 1 | SUPPORT, bracket to fuel pump |
| 12 | 844-10040 | 1 | BOLT, Hex Flg, M10 x 40, 8.8, BOLT – heavy hex flange, 10 – 1.5 x 30 mm, support to pump |
| 13 | 845-8045 | 1 | BOLT, Hex Flg, M8 x 45, 8.8, BOLT – heavy hex flange, 8 – 1.25 x 45 mm, upper bracket to support |
| 14 | J900589 | 1 | NUT, hex flange, special, 8 mm |
| 15 | J924605 | 1 | SEAL, SEAL – rectangular ring, injection pump to gear housing |
| 16 | J931928 | 1 | ELBOW, 90 degree, replaces 222-1704 elbow |
| 17 | J917074 | 1 | HOSE, 508 mm (20 inch) long, mounts to rear of the governor housing, replaces J916779 hose |
| 18 | J918002 | 1 | BOLT, BANJO, banjo |
| 19 | J918190 | 2 | WASHER, SEALING, WASHER – sealing, special, 10 x 15.5 x 1 mm |
| 20 | J930842 | 1 | HOSE, 330 mm (13 inch) long, engine serial number 45361257 and after, use with 235337A1 hose |
| 21 | A171099 | 1 | CLAMP, HOSE, spring-type, adjustable |
| 22 | J930252 | 1 | SUPPORT, BRACKET – solenoid mounting |
| 23 | 854-10020 | 2 | BOLT, Hex Flg, M10 x 20, 10.9 |
| 24 | 854-10025 | 2 | BOLT, Hex Flg, M10 x 25, 10.9, BOLT – heavy hex flange, 10 – 1.5 x 25 mm, class 10.9 |
| 25 | 845-8050 | 4 | BOLT, Hex Flg, M8 x 50, 8.8 |
| 26 | J920639 | 2 | BRACE, fuel pump |
| 27 | J922672 | 1 | HOLDER, SUPPORT – fuel pump |
| 28 | J930235 | 1 | SOLENOID, fuel shutoff, 12 volt, Includes: Ref. 29-34 |
| 29 | L53928 | 1 | EYE, JOINT – ball, replaces A146456 joint, not shown |
| 30 | 492-11025 | 1 | WASHER, LOCK, 1/4″, Not shown |
| 31 | 425-154 | 1 | NUT, Jam, 1/4″-28, G5, Not shown |
| 32 | J925171 | 1 | BOOT, protective, plunger, not shown |
| 33 | 473321C1 | 1 | STRAP, CABLE, .098″ x 8″, tie, not shown |
| 34 | J924407 | 1 | SPRING, return, plunger, not shown |
| 35 | J912886 | 1 | VALVE, overflow |
| 36 | J911447 | 1 | CONNECTOR, banjo, fuel return |
| 37 | J918192 | 2 | RING, PACKING, WASHER – sealing, special, 14 x 20 x 1 mm |
| 38 | 97010C1 | 4 | BOLT, SPREADER, hex flange, 6 – 1.0 x 12 mm |
| 39 | J924962 | 1 | BOLT, hex flange, special, 8 – 1.25 x 16 mm, fuel shut-off solenoid to injection pump, not shown |
| 1 | J909886 | 1 | SEAL, SLEEVE – injector, sealing |
| 2 | J903380 | 1 | SEAL, connector |
| 3 | J930525 | 1 | INJECTOR ASSY., fuel, Bosch, 8930 and 8940 tractors, Whenever a nozzle is removed from cylinder |
| 3 | J926787 | 1 | INJECTOR ASSY., fuel, Bosch, 8950 tractor, Whenever a nozzle is removed from cylinder head |
| 5 | J905153 | 1 | SPINDLE, SEAT – nozzle pressure spring |
| 6 | J905152 | 1 | SPRING, nozzle pressure |
| 7 | J905154 | 1 | PLATE, STOP – nozzle valve |
| 11 | J923261 | 6 | WASHER, SEAL – injector nozzle, 2.5 mm thick, 7 mm injector tip, Whenever a nozzle is removed from |
| 1 | 302488A1 | 1 | LEVER, throttle control, replaces 220361A1 lever |
| 2 | 1975823C2 | 1 | HANDLE, KNOB – control lever |
| 3 | 96576C1 | 1 | BUSHING, LARGE, control lever |
| 4 | 800-3120 | 1 | CIRCLIP, M20, E-type, external retaining, No. 20 |
| 5 | 864-4030 | 1 | SCREW, Hex Soc Hd, M4 x 30, 8.8, BOLT – hex socket, 4 – 0.7 x 30 mm |
| 6 | 832-10404 | 1 | NUT, LOCK, M4 x .7, Cl 8, hex, self-locking, 4 mm – 0.7 |
| 7 | 198834A1 | 1 | SUPPORT, BRACKET – throttle lever |
| 8 | 627-6016 | 2 | BOLT, Hex, M6 x 16, 10.9, Full threads |
| 9 | 896-11006 | 2 | WASHER, M6 x 13 x 2, HT |
| 10 | 892-11006 | 2 | WASHER, LOCK, M6 |
| 14 | 1974525C2 | 1 | BALL JOINT, throttle cable |
| 15 | 95-81060 | 1 | WASHER, 7/32″ x 9/16″ x .060″, flat, 7/32 x 9/16 x 1/16 inch |
| 16 | 432-48 | 1 | PIN, SPLIT (COTTER), 1/16″ x 1/2″ |
| 18 | 230-4714 | 1 | NUT, LOCK, 1/4″-28, GA, hex, self-locking, 1/4 inch NF |
| 19 | 224475A2 | 1 | SUPPORT, BRACKET – throttle cable |
| 20 | 614-10025 | 2 | BOLT, Hex, M10 x 25, 8.8, Full Thd |
| 22 | 492-11010 | 1 | WASHER, LOCK, #10 |
| 23 | 225-14210 | 1 | NUT, #10-32 |
| 26 | 1267688C3 | 1 | CABLE, throttle, INCLUDES REF 27 |
| 27 | 96988C2 | 1 | GROMMET, cable |
| 28 | A75815 | 1 | CLAMP, retaining |
| 29 | 461-31016 | 2 | SCREW, Hex Soc Hd, #10-24 x 1″, BOLT – hex socket, No. 10 NC x 1 inch |
| 32 | L40315 | 1 | SHIM, clamp |
| 33 | 224900A1 | 1 | PLATE, LARGE, cable clamp |
| 21 | 895-15010 | 2 | WASHER, M11 x 24 x 2 |
| 1 | 1975959C4 | 1 | PEDAL ASSY., foot throttle, with pad |
| 2 | 434-516 | 1 | BOLT, CARRIAGE, Short NK, 5/16″-18 x 1″, G5, Full Thd |
| 3 | 425-145 | 1 | NUT, Jam, 5/16″-18, G5 |
| 4 | 97043C4 | 1 | SHAFT, throttle pedal |
| 5 | 1975973C1 | 1 | BUSHING, LARGE, left, long |
| 6 | 1975974C1 | 1 | BUSHING, LARGE, right, short |
| 7 | 38-3816 | 1 | PIN, 1/8″ x 1″, Coiled, 1/8″ x 1″, Coiled |
| 8 | 220355A1 | 1 | LEVER ASSY., throttle pedal |
| 9 | 1977463C1 | 1 | STOP, throttle pedal |
| 10 | 97046C4 | 1 | SUPPORT, throttle pedal |
| 11 | 614-8020 | 3 | BOLT, Hex, M8 x 20, 8.8 |
| 12 | 892-11008 | 3 | WASHER, LOCK, M8 |
| 18 | 97173C4 | 1 | CABLE, foot throttle |
| 19 | 225-14210 | 1 | NUT, #10-32 |
| 20 | 432-48 | 1 | PIN, SPLIT (COTTER), 1/16″ x 1/2″ |
| 21 | 1975966C1 | 2 | SPRING, detent |
| 22 | 220359A1 | 1 | SUPPORT ASSY., BRACKET – cable, foot throttle, no longer available, order 220358A3 bracket below |
| 22 | 220358A3 | 1 | SUPPORT ASSY., BRACKET – cable, foot throttle |
| 23 | 627-6016 | 2 | BOLT, Hex, M6 x 16, 10.9, Full threads |
| 24 | 892-11006 | 2 | WASHER, LOCK, M6 |
| 26 | A75815 | 2 | CLAMP, retaining |
| 27 | L40315 | 2 | SHIM, clamp |
| 28 | 461-31016 | 4 | SCREW, Hex Soc Hd, #10-24 x 1″, BOLT – hex socket, No. 10 NC x 1 inch |
| 30 | 224900A1 | 2 | PLATE, LARGE, ocking, cable clamp |
| 34 | 224475A2 | 1 | SUPPORT, BRACKET – throttle cable |
| 37 | 19725R1 | 1 | BALL JOINT, foot throttle |
| 38 | 225-14210 | 1 | NUT, #10-32 |
| 39 | 193-1000 | 1 | NUT, Keps, w/LW,#10-32, hex, with external tooth lock washer, No. 10 NF |
| 40 | 1974525C2 | 1 | BALL JOINT, throttle cable |
| 41 | 1971259C1 | 1 | SPACER, 3/8 ID x 7/32 inch |
| 42 | 495-81107 | 2 | WASHER, .281″ x 7/8″ x .060″, flat, 9/32 x 7/8 x 3/64 inch |
| 43 | 230-4714 | 1 | NUT, LOCK, 1/4″-28, GA, hex, self-locking, 1/4 inch NF |
| 44 | 198834A1 | 1 | SUPPORT, BRACKET – throttle lever |
| 46 | 225-14210 | 1 | NUT, #10-32 |
| 47 | 492-11010 | 1 | WASHER, LOCK, #10 |
| 48 | 829-1406 | 1 | NUT, M6, Cl 10, Used with 220358A3 bracket, not shown |
| 49 | 473321C1 | 1 | STRAP, CABLE, .098″ x 8″, tie, not shown |
| 1 | 96903C5 | 1 | RESERVOIR, TANK ASSEMBLY – fuel, main, (87 gallon capacity) includes items 21-23 on Figure 3-32 |
| 2 | 1283682C1 | 1 | TUBE, tank inlet |
| 3 | 97226C1 | 1 | O-RING, fuel inlet |
| 4 | 840-1620 | 6 | SCREW, Cross Pan Hd, M6 x 20 |
| 5 | 1283825C1 | 1 | HOSE ASSY., 90 degree, inlet |
| 6 | 214-1544 | 2 | CLAMP, HOSE, #44, 2.31/3.25 Type F Worm, W/liner, adj, 2-5/16 – 3-1/4 inch dia, hose retaining |
| 7 | 1283783C2 | 1 | TUBE, filter |
| 8 | 1283807C1 | 1 | COLLAR, filler neck |
| 9 | 1283826C2 | 1 | CAP, fuel filler |
| 10 | 259110A1 | 1 | GAUGE, FUEL, SENSOR – fuel level, main tank without auxiliary tank, also order item 17, replaces |
| 10 | 259111A1 | 1 | GAUGE, FUEL, SENSOR – fuel level, main tank, models with auxiliary tank, also order item 17 |
| 17 | 104812C3 | 1 | GASKET, fuel level sender |
| 18 | 193-563 | 5 | SCREW, SEMS, Hex Hd, #10-24 x 3/4″, G5, hex, with external tooth lock, No. 10 NC x 3/4 inch |
| 19 | 1283890C1 | 1 | HOSE ASSY., tank vent |
| 20 | 214-1410 | 2 | CLAMP, HOSE, #10, 0.56/1.06 Type F Worm, Adjustable |
| 23 | 120589A1 | 1 | SUPPORT ASSY., tank |
| 24 | 614-10020 | 4 | BOLT, Hex, M10 x 20, 8.8, Full Thd |
| 25 | 825-1410 | 8 | NUT, M10, Cl 8 |
| 26 | 137630C2 | 1 | BRACKET, hold down, fuel tank |
| 27 | 1287737C1 | 4 | SCREW, BOLT – hex, 10 x 25 mm class 10.9, special |
| 28 | 1287738C2 | 2 | WASHER, flat, 11 x 21 x 3 mm |
| 29 | 120587A1 | 1 | SUPPORT, BRACKET – upper link |
| 32 | 1283792C1 | 1 | MOUNTING CLIP, CLAMP – tube retaining |
| 33 | 614-8020 | 2 | BOLT, Hex, M8 x 20, 8.8 |
| 34 | 825-2408 | 2 | NUT, M8 x 1.25, Flg, Cl 8 |
| 36 | 1971391C1 | 2 | CLIP, retainer, chain |
| 37 | 1971392C1 | 1 | CHAIN (AGRICULTURE), fuel cap, 10 inch |
| 38 | A143035 | 1 | NUT, FASTENER – stud |
| 39 | 120157C1 | 1 | CONNECTOR, fuel tank |
| 40 | 536652R1 | 1 | WASHER, flat |
| 1 | 96903C4 | 1 | RESERVOIR, TANK ASSEMBLY – fuel, main, (87 gallon capacity) includes items 21-23, also order |
| 2 | 214-1428 | 2 | CLAMP, HOSE, #28, 1.31/2.25 Type F Worm |
| 3 | 130345C1 | 1 | HOSE, 60mm (2-3/8 inch) long, fuel tank outlet |
| 4 | 196250A1 | 1 | ADAPTER, fuel line hose to shutoff valve |
| 5 | 196465A1 | 1 | COCK, DRAIN, VALVE – fuel shutoff |
| 6 | 196262A1 | 1 | PIPE, TUBE – fuel line, at tank |
| 7 | 196252A1 | 4 | CLAMP, fuel supply |
| 8 | 196251A1 | 1 | HOSE, 13 (1/2) x 20 (25/32) x 1700 mm (x 66-15/16 inch) long, fuel supply |
| 9 | 196249A1 | 1 | CONDUIT, SLEEVE – corrugated, 27 (1-1/16) ID x 1000 mm (39-3/8 inch) long, cut from 291260A2 |
| 10 | 1954474C4 | 1 | SHIN, CLAMP – at left front cab support |
| 12 | 194199A1 | 1 | FILTER, STRAINER, fuel, in-line |
| 13 | 196247A1 | 1 | HOSE, 13 (1/2) x 20 (25/32) x 78 mm (3-5/64 inch) long, filter to engine |
| 14 | 197095A1 | 1 | ELBOW, 90 degree, 1/2 barb end x 1/2 inch PT |
| 15 | A171099 | 6 | CLAMP, HOSE, spring-type, hose |
| 16 | 196266A2 | 1 | HOSE, 8 (21/64) x 15 (5/8) x 3750 mm (147-5/8 inch) long, fuel return to tank |
| 17 | 196245A2 | 1 | LOOM, SLEEVE – corrugated, 17 (5/8) ID x 3700 mm (145-11/16 inch) long, fuel return |
| 18 | 259110A1 | 1 | GAUGE, FUEL, SENSOR – fuel level, main tank, models without auxiliary tank, also order item 20 |
| 19 | 193-563 | 5 | SCREW, SEMS, Hex Hd, #10-24 x 3/4″, G5, hex, with external tooth lock, No. 10 NC x 3/4 inch |
| 20 | 104812C3 | 1 | GASKET, fuel level sender |
| 21 | 238-5210 | 1 | O-RING, -210, 70 Duro, .734″ ID x .139″ Thk |
| 22 | 1251790C1 | 1 | FITTING, ADAPTER – straight, fuel tank drain |
| 23 | 1251791C1 | 1 | NUT, hex, jam, special |
| 24 | 104465C1 | 1 | VALVE, DRAIN, main fuel tank |
| 25 | 104896C1 | 1 | TUBE, fuel tank drain, 457 mm (18 inch) long, cut from 74813C1 bulk tube |
| 26 | 195509A1 | 1 | COUPLING, CONNECTOR – 5/16 inch hose |
| 27 | 225005A1 | 1 | HOSE, 8 (21/64) x 15 (5/8) x 1650 mm x (65 inch) long, fuel cooler to main tank |
| 28 | 225006A1 | 1 | LOOM, SLEEVE – corrugated, 17 (5/8) ID x 1600 mm (63 inch) long |
| 30 | 196248A1 | 1 | LOOM, SLEEVE – corrugated, 27 (1-1/6) ID x 560 mm (22-3/64 inch) long, cut from 291260A2 bulk |
| 31 | 195509A1 | 1 | COUPLING, CONNECTOR – at fuel injection pump |
| 32 | 235337A1 | 1 | HOSE, 8 (21/64) x 15 (5/8) x 1345 mm (53 inch) long, fuel injection pump to fuel cooler |
| 33 | 196246A1 | 1 | CONDUIT, SLEEVE – corrugated, 17 (5/8) ID x 1650 mm (65 inch) long, cut from 291260A2 bulk sleeve |
| 34 | 362123R1 | 1 | CLIP, hose |
| 1 | 137700C6 | 1 | RESERVOIR, TANK ASSEMBLY – fuel, auxiliary, standard capacity (17 gallons), also order 104812C3 |
| 2 | 1251790C1 | 1 | FITTING, ADAPTER – straight |
| 3 | 238-5210 | 1 | O-RING, -210, 70 Duro, .734″ ID x .139″ Thk |
| 4 | 1251791C1 | 1 | NUT, hex, jam, special |
| 5 | 217-103 | 1 | COCK, DRAIN, VALVE – 1/4 inch PT, drain |
| 17 | 137702C5 | 1 | SUPPORT ASSY., tank |
| 18 | 614-12025 | 3 | BOLT, Hex, M12 x 25, 8.8, Full threads, Front support and tank support |
| 19 | 1280992C2 | 1 | SUPPORT ASSY., tank, rear |
| 20 | 137704C2 | 1 | SUPPORT ASSY., tank, front |
| 21 | 614-12025 | 2 | BOLT, Hex, M12 x 25, 8.8, Full threads |
| 22 | 9804279 | 2 | NUT, M12 x 1.75, Flg, Cl 8, hex flange, 12 mm – 1.75 |
| 23 | 1259898C1 | 1 | BRACKET, retaining, tank |
| 24 | 144252C2 | 1 | STIFFENER, BRACKET – hold down, tank |
| 25 | 1251937C1 | 1 | REINFORCEMENT, CHANNEL – brace, tank |
| 26 | 614-10020 | 2 | BOLT, Hex, M10 x 20, 8.8, Full Thd |
| 27 | 825-1410 | 2 | NUT, M10, Cl 8 |
| 28 | 1259899C1 | 1 | SPACER, support, front |
| 29 | 814-10040 | 1 | BOLT, Hex, M10 x 40, 8.8, Full Thd |
| 30 | 144253C1 | 1 | SPACER, support, rear |
| 31 | 814-10045 | 1 | BOLT, Hex, M10 x 45, 8.8 |
| 32 | 97013C1 | 1 | HOSE ASSY., tank, auxiliary |
| 33 | 214-1428 | 2 | CLAMP, HOSE, #28, 1.31/2.25 Type F Worm |
| 34 | 193855A2 | 1 | GAUGE, FUEL, SENSOR – auxiliary tank level, also order item 35 |
| 35 | 104812C3 | 1 | GASKET, fuel level sender |
| 36 | 1978426C1 | 5 | SCREW, pan Phillips, with O-ring, No 10 – 24 x 3/4 inch |
| 37 | 196265A1 | 1 | HOSE, 8 (21/64) x 15 (5/8) x 3530 mm (139 inch) long, fuel cooler to auxiliary tank |
| 38 | A171099 | 2 | CLAMP, HOSE, spring-type, hose, retaining |
| 39 | 196244A1 | 1 | LOOM, SLEEVE – corrugated, 17 (5/8) ID x 3480 mm (137 inch) long |
| 40 | 103010A1 | 1 | HOSE, 1970 mm (77-9/16 inch) long, auxiliary tank |
| 41 | 103011A1 | 1 | CONDUIT, SLEEVE – corrugated, 17 (5/8) ID x 1841 mm (72-1/2 inch) long, cut from 291262A2 bulk |
| 42 | A171099 | 2 | CLAMP, HOSE, spring-type |
| 43 | 196465A1 | 1 | COCK, DRAIN, VALVE – fuel shutoff, brass, supply |
| 44 | 196458A1 | 1 | TUBE, CONNECTOR – barb, 1/2 barb x 1/2 inch female pipe |
| 45 | 196267A1 | 1 | HOSE, 13 (1/2) x 20 (25/32) x 1235 mm (48-5/8 inch) long, fuel supply, auxiliary tank to in-line filter |
| 46 | 196248A1 | 1 | LOOM, SLEEVE – corrugated, 27 (1-1/6) ID x 560 mm (22-3/64 inch) long, cut from 291260A2 bulk |
| 47 | 196252A1 | 1 | CLAMP, hose at supply valve connector |
| 48 | 194199A1 | 1 | FILTER, STRAINER, fuel, in-line |
| 49 | 196247A1 | 1 | HOSE, 13 (1/2) x 20 (25/32) x 78 mm (3-5/64 inch) long, fuel filter to lift pump |
| 50 | 196252A1 | 3 | CLAMP, at in-line filter |
| 51 | 197095A1 | 1 | ELBOW, 90 degree, 1/2 barb end x 1/2 inch PT |
| 53 | 235337A1 | 1 | HOSE, 8 (21/64) x 15 (5/8) x 1345 mm (53 inch) long, fuel injection pump to fuel cooler. Use with |
| 54 | 196246A1 | 1 | CONDUIT, SLEEVE – corrugated, 17 (5/8) ID x 1650 mm (65 inch) long, cut from 291262A2 bulk sleeve |
| 55 | A171099 | 3 | CLAMP, HOSE, spring-type, hose |
| 56 | 195509A1 | 1 | COUPLING, CONNECTOR – barbed, 5/16 inch hose |
| 57 | 362123R1 | 1 | CLIP, hose |
| 58 | 1954474C4 | 1 | SHIN, CLAMP – fuel line, at left front cab support, return and supply lines |
| 59 | 193-1000 | 1 | NUT, Keps, w/LW,#10-32, hex, with external tooth lock washer, No. 10 NF, harness electrical lead to |
| 60 | 813-16140 | 1 | BOLT, Hex, M16 x 140, 8.8, BOLT – hex, 16 – 2.0 x 140 mm |
| 62 | 306132C1 | 2 | STRAP, CABLE, .30″ x 14.5″, tie, 14 inch long |
| 1 | 258474A1 | 1 | TANK, FUEL, ASSEMBLY – fuel, auxiliary extended capacity (30 gallons), Includes: Ref. 2, 3, 4 |
| 2 | 1251790C1 | 1 | FITTING, ADAPTER – straight |
| 3 | 238-5210 | 1 | O-RING, -210, 70 Duro, .734″ ID x .139″ Thk |
| 4 | 1251791C1 | 1 | NUT, hex, jam, special |
| 5 | 217-103 | 1 | COCK, DRAIN, VALVE – 1/4 inch PT, drain |
| 6 | 258005A1 | 1 | PLATE, LARGE, auxiliary fuel tank, axle |
| 7 | 814-16130 | 2 | BOLT, Hex, M16 x 130, 8.8, BOLT – hex, 16 – 2.0 x 130 mm |
| 8 | 253732A2 | 1 | SUPPORT, auxiliary fuel tank, rear |
| 9 | 814-10040 | 2 | BOLT, Hex, M10 x 40, 8.8, Full Thd |
| 10 | 892-11010 | 2 | WASHER, LOCK, M10 |
| 11 | 252290A2 | 1 | PLATE, auxiliary fuel tank |
| 12 | 844-10020 | 4 | BOLT, Hex Flg, M10 x 20, 8.8 |
| 13 | 495-81140 | 4 | WASHER, 13/32″ x 1 1/4″ x .060″ |
| 14 | 495-81143 | 2 | WASHER, 13/32″ x 1 1/2″ x .120″, flat, 13/32 x 1-1/2 x 7/64 inch |
| 15 | 892-11010 | 4 | WASHER, LOCK, M10 |
| 17 | 137702C5 | 1 | SUPPORT ASSY., tank |
| 18 | 614-12025 | 4 | BOLT, Hex, M12 x 25, 8.8, Full threads, Front support and tank support |
| 19 | 1280992C2 | 1 | SUPPORT ASSY., tank, rear |
| 20 | 137704C2 | 1 | SUPPORT ASSY., tank, front |
| 21 | 614-12025 | 2 | BOLT, Hex, M12 x 25, 8.8, Full threads |
| 22 | 9804279 | 2 | NUT, M12 x 1.75, Flg, Cl 8, hex flange, 12 mm – 1.75 |
| 23 | 1259898C1 | 1 | BRACKET, retaining, tank |
| 24 | 144252C2 | 1 | STIFFENER, BRACKET – hold down, tank |
| 25 | 1251937C1 | 1 | REINFORCEMENT, CHANNEL – brace, tank |
| 26 | 614-10020 | 2 | BOLT, Hex, M10 x 20, 8.8, Full Thd |
| 27 | 825-1410 | 2 | NUT, M10, Cl 8 |
| 28 | 1259899C1 | 1 | SPACER, support, front |
| 29 | 814-10040 | 2 | BOLT, Hex, M10 x 40, 8.8, Full Thd |
| 30 | 144253C1 | 2 | SPACER, support, rear |
| 31 | 814-10045 | 1 | BOLT, Hex, M10 x 45, 8.8 |
| 32 | 97013C1 | 1 | HOSE ASSY., tank, auxiliary |
| 33 | 214-1428 | 2 | CLAMP, HOSE, #28, 1.31/2.25 Type F Worm |
| 34 | 193855A2 | 1 | GAUGE, FUEL, SENSOR – auxiliary fuel tank level |
| 35 | 104812C3 | 1 | GASKET, fuel level sender |
| 36 | 1978426C1 | 5 | SCREW, pan Phillips, with O-ring, No. 10 – 24 x 3/4 inch |
| 37 | 196265A1 | 1 | HOSE, 8 (21/64) x 15 (5/8) x 3530 mm (139 inch) long, fuel return, fuel cooler to auxiliary tank |
| 38 | 196244A1 | 1 | LOOM, SLEEVE – corrugated, 17 (5/8) ID x 3480 mm (137 inch) long |
| 39 | A171099 | 2 | CLAMP, HOSE, spring-type, hose, retaining |
| 40 | 103010A1 | 1 | HOSE, 1970 mm (77-9/16 inch) long, vent, auxiliary tank |
| 41 | 103011A1 | 1 | CONDUIT, SLEEVE – corrugated, 17 (5/8) ID x 1841 mm (72-1/2 inch) long, cut from 291262A2 bulk |
| 42 | A171099 | 2 | CLAMP, HOSE, spring-type |
| 43 | 196465A1 | 1 | COCK, DRAIN, VALVE – fuel shutoff, supply, brass |
| 44 | 196458A1 | 1 | TUBE, CONNECTOR – barb, 1/2 barb x 1/2 inch female pipe |
| 45 | 196267A1 | 1 | HOSE, 13 (1/2) x 20 (25/32) x 1235 mm (48-5/8 inch) long, fuel supply, auxiliary tank to in-line filter |
| 46 | 196248A1 | 1 | LOOM, SLEEVE – sorrugated, 27 (1-1/6) ID x 560 mm (22-3/64 inch) long, cut from 291260A2 bulk |
| 47 | 196252A1 | 1 | CLAMP, hose at supply valve connector |
| 48 | 194199A1 | 1 | FILTER, STRAINER, fuel, in-line |
| 49 | 196247A1 | 1 | HOSE, 13 (1/2) x 20 (25/32) x 78 mm (3-5/64 inch) long, fuel filter to lift pump |
| 50 | 196252A1 | 3 | CLAMP, at in-line fuel filter |
| 51 | 197095A1 | 1 | ELBOW, 90 degree, 1/2 barb end x 1/2 inch PT |
| 52 | 217-1012 | 1 | ADAPTER, 1/4″-18 Male NPTF x 3/8″-18 Female NPTF, ADAPTER – straight, 1/4 PT x 3/8 inch female |
| 53 | 235337A1 | 1 | HOSE, 8 (21/64) x 15 (5/8) x 1345 mm (53 inch) long, fuel injection pump to fuel cooler |
| 54 | 196246A1 | 1 | CONDUIT, SLEEVE – corrugated, 17 ( 5/8) ID x 1650 mm (65 inch) long, cut from 291262A2 bulk sleeve |
| 55 | A171099 | 3 | CLAMP, HOSE, spring-type, hose |
| 56 | 195509A1 | 1 | COUPLING, CONNECTOR – barbed, 5/16 inch hose |
| 57 | 362123R1 | 1 | CLIP, hose |
| 58 | 1954474C4 | 1 | SHIN, CLAMP – fuel line, at left front cab support, return and supply lines |
| 59 | 193-1000 | 1 | NUT, Keps, w/LW,#10-32, hex, with external tooth lock washer, No. 10 NF, harness electrical lead to |
| 60 | 813-16140 | 1 | BOLT, Hex, M16 x 140, 8.8, BOLT – hex, 16 – 2.0 x 140 mm, if used, machines without 258005A1 plate |
| 62 | 306132C1 | 2 | STRAP, CABLE, .30″ x 14.5″, tie, 14 inch long, nylon |
| 16 | 829-1410 | 2 | NUT, M10, Cl 10 |
| 1 | 189571A2 | 1 | HARNESS, cab, lower, prior to serial number JJA0090823 |
| 2 | A177090 | 1 | HARNESS, monitor, implement |
| 3 | 1964859C6 | 1 | CLUSTER, ASSEMBLY – instrument, new, parts list Figure 4-22 |
| 4 | 92385C1 | 3 | CLIP, retaining |
| 5 | 492-11038 | 3 | WASHER, LOCK, 3/8″ |
| 6 | 92365C1 | 2 | SWITCH, horn and ether start |
| 7 | 282775A1 | 1 | SWITCH, IGNITION, ASSEMBLY – includes keys, includes padded keys item 11 |
| 7 | D134737 | 1 | SWITCH, IGNITION, SWITCH ASSEMBLY – iginition, includes keys, Includes: Ref. 8, 9 |
| 8 | A77314 | 1 | NUT, hex, special |
| 9 | A77313 | 1 | SET OF 2 KEYS, metal without padding |
| 10 | 1964785C1 | 1 | NUT, mounting, ignition switch |
| 11 | 1964831C2 | 1 | SET OF 2 KEYS, padded, included with switch assembly 282775A1, if used |
| 12 | 122860A1 | 1 | NUT, switch |
| 13 | 92385C1 | 1 | CLIP, retaining, harness |
| 14 | 123014A1 | 2 | SWITCH, brake, differential lock |
| 15 | 151-535 | 4 | RIVET, Pop, 1/8″ x .462″, break mandrel, 1/8 x 15/32 inch, to mount three pin connector |
| 16 | 468647C2 | 1 | BLOCK ASSY., junction, parts list Figure 4-26 |
| 17 | 1964561C1 | 1 | BAR, junction block buss, parts list Figure 4-26 |
| 19 | 1964773C1 | 1 | LIGHTER, CIGARETTE, ASSEMBLY – 12 volt, Includes: Ref. 20 |
| 20 | A177447 | 1 | LIGHTER, CIGARETTE, ELEMENT – pop-out unit, small knob |
| 21 | 425-166 | 3 | NUT, 3/8″-16, G5, Hvy, heavy hex, 3/8 inch NC |
| 23 | 92346C1 | 1 | SWITCH, differential lock, Includes: Switch, Socket, Bulb, and Lens |
| 24 | 91921C1 | 1 | SWITCH, lighting |
| 25 | 97107C3 | 1 | BUTTON, KNOB – light switch |
| 27 | 129130A1 | 1 | SWITCH, MFD, Includes: Switch, Socket, Bulb, and Lens |
| 28 | 245918C1 | 1 | CAP, PLUG – rectangular, blanking, if used |
| 29 | 92344C1 | 1 | SWITCH, ASSEMBLY – high/low, Includes: Switch, Bulb, Socket, and Decal |
| 30 | 1987422C1 | 1 | SWITCH, and flasher, prior to serial number JJA0090823 |
| 31 | 131-428 | 1 | NUT, LOCK, PAL, 3/4″-20, hex, self-locking, 3/4-20 inch, used with 1987422c1 switch |
| 32 | 92389C2 | 1 | UNIT, FLASHER, hazard, effective serial number JJA0090823 through JJA0090943 |
| 33 | 780-34395 | 1 | SCREW, SELF TAPPING, Hex Wash Hd, M4.8 x 9.5, S/N JJA0090944 and after, Not shown |
| 34 | 97102C1 | 1 | ADAPTER, lever, turn signal |
| 35 | 170-104 | 1 | SCREW, Sltd Pan Hd, #5-40 x 3/8″, machine, pan head Phillips, No. 5 NC x 3/8 inch |
| 36 | 1329896C1 | 1 | CLASP, CLIP – retaining, lever |
| 37 | 97103C3 | 1 | LEVER, turn signal, prior to serial number JJA0090823 |
| 42 | 92043C3 | 1 | SWITCH, drive, creeper |
| 44 | 96890C2 | 1 | BRACKET, creeper switch |
| 45 | 1983363C2 | 1 | LAMP, LIGHT ASSEMBLY – cluster, Includes: Ref. 46 |
| 46 | F64363 | 1 | BULB, lamp |
| 47 | 104389C1 | 1 | CLIP, retaining, light |
| 48 | 3141107R1 | 4 | BULB, W5/1.2, 12V, 1.2W, 2 watt |
| 49 | 459330C1 | 2 | WASHER, LOCK, lock, No. 24 |
| 50 | 459329C1 | 2 | NUT, hex, No. 24 |
| 51 | 137430A1 | 1 | SWITCH, ASSEMBLY – override shutdown, Includes: switch, Socket, Bulb and Decal |
| 52 | 113699A1 | 2 | RECTIFIER, locking, 2-5/8 inch long |
| 54 | 189574A2 | 1 | SWITCH, IGNITION, toggle, PTO |
| 55 | 896-15012 | 1 | WASHER, M12 x 28.5 x 4, HT, flat, 13.5 x 28 x 4 mm, hardened |
| 56 | 223565A1 | 1 | KNOB,BALL, control, PTO switch |
| 57 | 183696A1 | 1 | INDICATOR, LAMP – green, PTO |
| 70 | 225164C1 | 1 | CONNECTOR, ELEC, electrical, type GH, implement receptacle, female |
| 71 | 225168C1 | 3 | TERMINAL CONNECTOR, electrical, female, 14-16 ga., type THI, not shown |
| 72 | 187103A1 | 1 | CONNECTOR, ELEC, auxiliary power, assembly, INCLUDES REFS 73-76 |
| 73 | 225165C1 | 1 | CONNECTOR, ELEC, electrical, type GQ, male, see item 77 for female connector |
| 74 | 225153C1 | 1 | CONNECTOR, ELEC, CONNECTOR – electrical, type GX, strain relief clamp |
| 75 | 225166C1 | 3 | PIN, ELECT TERMINAL, electrical, male blade, 14-16 ga., type TJ1, not shown |
| 77 | 245485C1 | 1 | CONNECTOR, ELEC, receptacle, type DK, female, implement plug auxiliary power source, not shown |
| 78 | 225119C1 | 1 | PIN, ELECT TERMINAL, TERMINAL – wire, type T1, 14 – 16 ga., used with 245485C1 connector, not |
| 1 | 232881A3 | 1 | HARNESS, cab, lower, with hitch, prior to serial number JJA0090823 |
| 2 | A177090 | 1 | HARNESS, monitor, implement |
| 3 | 1964859C6 | 1 | CLUSTER, ASSEMBLY – instrument, new, parts list Figure 4-22 |
| 4 | 92385C1 | 3 | CLIP, retaining |
| 5 | 492-11038 | 3 | WASHER, LOCK, 3/8″ |
| 6 | 92365C1 | 2 | SWITCH, horn and ether start |
| 7 | 282775A1 | 1 | SWITCH, IGNITION, ASSEMBLY – includes keys, padded, item 11, if used, Includes: Ref. 8, 9 |
| 7 | D134737 | 1 | SWITCH, IGNITION, SWITCH ASSEMBLY – ignition, includes keys, metal, if used |
| 8 | A77314 | 1 | NUT, hex, special |
| 9 | A77313 | 1 | SET OF 2 KEYS, metal without padding |
| 10 | 1964785C1 | 1 | NUT, mounting, ignition switch |
| 11 | 1964831C2 | 1 | SET OF 2 KEYS, padded, included with switch assembly 282775A1, if used |
| 12 | 122860A1 | 1 | NUT, switch |
| 13 | 92385C1 | 1 | CLIP, retaining, harness |
| 14 | 123014A1 | 2 | SWITCH, brake, differential lock |
| 15 | 151-535 | 4 | RIVET, Pop, 1/8″ x .462″, break mandrel, 1/8 x 15/32 inch, to mount three pin connector |
| 16 | 468647C2 | 1 | BLOCK ASSY., junction, parts list Figure 4-26 |
| 17 | 1964561C1 | 1 | BAR, junction block buss, parts list Figure 4-26 |
| 19 | 1964773C1 | 1 | LIGHTER, CIGARETTE, ASSEMBLY – 12 volt |
| 20 | A177447 | 1 | LIGHTER, CIGARETTE, ELEMENT – pop-out unit, small knob |
| 21 | 425-166 | 3 | NUT, 3/8″-16, G5, Hvy, heavy hex, 3/8 inch NC |
| 23 | 236598A1 | 1 | SWITCH, differential lock |
| 24 | 91921C1 | 1 | SWITCH, lighting |
| 25 | 97107C3 | 1 | BUTTON, KNOB – light switch |
| 27 | 236596A1 | 1 | SWITCH, MFD |
| 28 | 245918C1 | 1 | CAP, PLUG – rectangular, blanking, if used |
| 29 | 92344C1 | 1 | SWITCH, ASSEMBLY – high/low, Includes: Switch, Socket, Bulb and Decal |
| 30 | 1987422C1 | 1 | SWITCH, and flasher, prior to serial number JJA0090823 |
| 31 | 131-428 | 1 | NUT, LOCK, PAL, 3/4″-20, hex, self-locking, 3/4-20 inch, used with 1987422C1 switch |
| 32 | 92389C2 | 1 | UNIT, FLASHER, hazard, effective serial number JJA0090823 through JJA0090943 |
| 33 | 780-34395 | 1 | SCREW, SELF TAPPING, Hex Wash Hd, M4.8 x 9.5, S/N JJA0090944 and after, Not shown |
| 34 | 97102C1 | 1 | ADAPTER, lever, turn signal |
| 35 | 170-104 | 1 | SCREW, Sltd Pan Hd, #5-40 x 3/8″, machine, pan head Phillips, No. 5 NC x 3/8 inch |
| 36 | 1329896C1 | 1 | CLASP, CLIP – retaining, lever |
| 37 | 97103C3 | 1 | LEVER, turn signal, prior to serial number JJA0090823 |
| 42 | 92043C3 | 1 | SWITCH, drive, creeper |
| 44 | 96890C2 | 1 | BRACKET, creeper switch |
| 45 | 1983363C2 | 1 | LAMP, LIGHT ASSEMBLY – cluster, Includes: Ref. 46 |
| 46 | F64363 | 1 | BULB, lamp |
| 47 | 104389C1 | 1 | CLIP, retaining, light |
| 48 | 3141107R1 | 4 | BULB, W5/1.2, 12V, 1.2W, 2 watt |
| 49 | 459330C1 | 2 | WASHER, LOCK, lock, No. 24 |
| 50 | 459329C1 | 2 | NUT, hex, No. 24 |
| 51 | 137430A1 | 1 | SWITCH, ASSEMBLY – override shutdown, Includes: Switch, Socket, Bulb, and Decal |
| 52 | 113699A1 | 2 | RECTIFIER, locking, 2-5/8 inch long |
| 54 | 189574A2 | 1 | SWITCH, IGNITION, toggle, PTO |
| 55 | 896-15012 | 1 | WASHER, M12 x 28.5 x 4, HT, flat, 13.5 x 28 x 4 mm, hardened |
| 56 | 223565A1 | 1 | KNOB,BALL, control, PTO switch |
| 57 | 183696A1 | 1 | INDICATOR, LAMP – green, PTO |
| 58 | 113663A1 | 1 | SWITCH, transport, field, momentary hitch raise/lower, Includes: Switch, Socket, Bulb and Lens |
| 59 | A186061 | 2 | POTENTIOMETER, electrical |
| 60 | 183696A1 | 1 | INDICATOR, LAMP – green |
| 61 | 235011A3 | 1 | PANEL, secondary control |
| 62 | 243549A1 | 1 | SWITCH, IGNITION, slip control, Includes: Socket and Bulb |
| 63 | 232825A2 | 1 | UNIT, MODULE – hitch |
| 64 | 896-11006 | 3 | WASHER, M6 x 13 x 2, HT |
| 65 | 825-1406 | 3 | NUT, M6, Cl 8 |
| 66 | 490691C1 | 1 | WASHER, lock |
| 67 | 490692C1 | 1 | NUT, hex, 1-1/2 inch |
| 68 | 781991C1 | 1 | BULB, C2F, #182, 14.4V, lamp, indicator |
| 69 | 114255A2 | 1 | POTENTIOMETER, GAUGE – position |
| 70 | 225164C1 | 1 | CONNECTOR, ELEC, electrical, type GH, implement receptacle, female |
| 71 | 225168C1 | 3 | TERMINAL CONNECTOR, electrical, female, 14-16 ga., type THI, not shown |
| 72 | 187103A1 | 1 | CONNECTOR, ELEC, auxiliary power, assembly, INCLUDES REFS 73-76 |
| 73 | 225165C1 | 1 | CONNECTOR, ELEC, electrical, type GQ, male, see item 77 for female connector |
| 74 | 225153C1 | 1 | CONNECTOR, ELEC, CONNECTOR – electrical, type GX, strain relief clamp |
| 75 | 225166C1 | 3 | PIN, ELECT TERMINAL, electrical, male blade, 14-16 ga., type TJ1, not shown |
| 77 | 245485C1 | 1 | CONNECTOR, ELEC, receptacle, type DK, female, implement plug auxillary power source, not shown |
| 78 | 225119C1 | 1 | PIN, ELECT TERMINAL, TERMINAL – wire, type T1, 14-16 ga., used with 245485C1 connector, not |
| 1 | 292552A2 | 1 | HARNESS, manual shuttle shift |
| 2 | 1343288C2 | 1 | LIMIT SWITCH, manual shuttle shift |
| 3 | 295056A1 | 1 | SUPPORT, BRACKET – switch mounting |
| 4 | 140-103 | 2 | SCREW, Cross Pan Hd, #6-32 x 3/4″ |
| 5 | 495-31016 | 2 | WASHER, #6 |
| 6 | 225-14106 | 2 | NUT, #6-32 |
| 7 | A149798 | 1 | FUSE, tan, 5 ampere |
| 8 | 1983394C2 | 1 | RELAY, mini, 12 volt |
| 9 | 291599A1 | 1 | SOLENOID, ASSEMBLY – manual shuttle shift, parts list Figure 6-61A |
| 11 | 614-10050 | 2 | BOLT, Hex, M10 x 50, 8.8, Full Thd, BOLT – hex, full threads, 10 – 1.5 x 50 mm |
| 12 | 829-2410 | 2 | NUT, M10 x 1.5, Flg, Cl 10 |
| 1 | 226666A1 | 1 | HARNESS, engine and front component |
| 3 | A187728 | 1 | MOTOR, STARTER, ASSEMBLY – engine, parts list Figure 4-32 |
| 4 | 91448C2 | 1 | ALTERNATOR, ASSEMBLY – engine, 110 ampere, parts list Figure 4-36 |
| 5 | 515-23127 | 1 | CLAMP, 1/2″, Insul, 3/8″ Bolt, P-type, 1/2 inch ID, closed |
| 6 | 515-2348 | 1 | CLAMP, 3/16″, Insul, 3/8″ Bolt, P-type, 10.3 mm ID |
| 7 | 515-22127 | 4 | CLAMP, 1/2″, Insul, 5/16″ Bolt, P-type, Closed |
| 9 | 516-22127 | 1 | CLAMP, J, 9/16″ Insul, 5/16″ Bolt, harness, open, 12.7 mm ID |
| 10 | L18337 | 3 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch, nylon |
| 13 | J930233 | 1 | SOLENOID, fuel shutoff, 12 volt, parts list page 3-018, 3-020, 8930 and 8940 Tractor |
| 13 | J930235 | 1 | SOLENOID, fuel shutoff, 12 volt, parts list figure 3-022, 8950 Tractor |
| 14 | 1987588C1 | 1 | SENSOR, exhaust gas temperature |
| 15 | 1999755C2 | 1 | COMPRESSOR, ASSEMBLY – air conditioning, component parts not serviced separately |
| 17 | A176566 | 1 | TRANSMITTER, SENDER – coolant temperature |
| 18 | 193-1000 | 1 | NUT, Keps, w/LW,#10-32, hex, with external tooth lock washer, No. 10 NF |
| 23 | 1546461C2 | 1 | SWITCH, oil pressure, 10 psi |
| 25 | 232948A1 | 1 | SWITCH, PRESSURE, high, 400 psi, air conditioning |
| 34 | 185552A2 | 1 | SOLENOID, ASSEMBLY – ether injection, parts list Figure 2-16 |
| 35 | 166166R1 | 1 | HORN, 12 volt, low note, replaces 251984A1 horn |
| 36 | 279476A1 | 1 | SENSOR, low coolant, coolant level |
| 44 | 1983640C1 | 1 | SWITCH, SWITCH – restriction, air cleaner |
| 45 | 362667R1 | 1 | CLIP, CLAMP – retainer, exhaust gas temperature to turbo elbow bracket |
| 46 | 614-10016 | 1 | BOLT, Hex, M10 x 16, 8.8, Full Thd, Ground Front Harness to Engine Block, If Used |
| 47 | 892-11010 | 1 | WASHER, LOCK, M10, If used |
| 48 | 281-34812 | 1 | SCREW, SELF TAPPING, Hex Hd, 5/16″ x 3/4″, self-tapping, hex washer head, 5/16 NC x 3/4 inch |
| 49 | 493-81008 | 1 | WASHER, LOCK, Int Tooth, 5/16″, internal tooth lock, 5/16 inch |
| 1 | 253622A1 | 1 | HARNESS, engine and front component |
| 3 | 193432A1 | 1 | MOTOR, STARTER, ASSEMBLY – engine, parts list Figure 4-35A |
| 4 | 91448C2 | 1 | ALTERNATOR, ASSEMBLY – engine, 110 ampere, parts list Figure 4-36 |
| 5 | 515-23127 | 1 | CLAMP, 1/2″, Insul, 3/8″ Bolt, P-type, 1/2 inch ID, closed |
| 6 | 515-2348 | 1 | CLAMP, 3/16″, Insul, 3/8″ Bolt, P-type, 10.3 mm ID |
| 7 | 515-22127 | 4 | CLAMP, 1/2″, Insul, 5/16″ Bolt, P-type, Closed |
| 9 | 516-22127 | 1 | CLAMP, J, 9/16″ Insul, 5/16″ Bolt, harness, open, 12.7 mm ID |
| 10 | L18337 | 3 | STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch, nylon |
| 13 | J930233 | 1 | SOLENOID, fuel shutoff, 12 volt, parts list page 3-018, 3-020, 8930 and 8940 Tractor |
| 13 | J930235 | 1 | SOLENOID, fuel shutoff, 12 volt, parts list figure 3-022, 8950 Tractor |
| 14 | 1987588C1 | 1 | SENSOR, exhaust gas temperature |
| 15 | 1999755C2 | 1 | COMPRESSOR, ASSEMBLY – air conditioning, component parts not serviced separately |
| 17 | A176566 | 1 | TRANSMITTER, SENDER – coolant temperature |
| 18 | 193-1000 | 1 | NUT, Keps, w/LW,#10-32, hex, with external tooth lock washer, No. 10 NF |
| 23 | 1546461C2 | 1 | SWITCH, oil pressure, 10 psi |
| 25 | 232948A1 | 1 | SWITCH, PRESSURE, high pressure, 400 psi, air conditioning |
| 34 | 185552A2 | 1 | SOLENOID, ASSEMBLY – ether injection, parts list Figure 2-16 |
| 35 | 166166R1 | 1 | HORN, 12 volt, low note, replaces 251984A1 horn |
| 36 | 279476A1 | 1 | SENSOR, low coolant, coolant level |
| 44 | 1983640C1 | 1 | SWITCH, SWITCH – restriction, air cleaner |
| 45 | 362667R1 | 1 | CLIP, CLAMP – retainer, exhaust gas temperature to turbo elbow bracket |
| 46 | 614-10016 | 1 | BOLT, Hex, M10 x 16, 8.8, Full Thd, Ground Front Harness to Engine Block, If Used |
| 47 | 892-11010 | 1 | WASHER, LOCK, M10, If used |
| 48 | 281-34812 | 1 | SCREW, SELF TAPPING, Hex Hd, 5/16″ x 3/4″, self-tapping, hex washer head, 5/16 NC x 3/4 inch |
| 49 | 493-81008 | 1 | WASHER, LOCK, Int Tooth, 5/16″, internal tooth lock, 5/16 inch |
| 1 | 189573A2 | 1 | HARNESS, transmission speed and range, prior to transmission serial number AJB0099462 |
| 1 | 320689A1 | 1 | HARNESS, transmission speed and range, transmission serial number AJB0099462 and after |
| 33 | 237-6005 | 1 | O-RING, 5-1, 90 Duro, .414″ ID x .072″ Thk |
| 16 | 1983218C2 | 1 | SWITCH, neutral start |
| 18 | A176566 | 1 | TRANSMITTER, SENDER – transmission oil temperature |
| 19 | 193-1000 | 1 | NUT, Keps, w/LW,#10-32, hex, with external tooth lock washer, No. 10 NF |
| 20 | 1546462C2 | 1 | SENSOR, lube oil pressure |
| 21 | 101813A2 | 1 | SWITCH, IGNITION, transmission system pressure, located on the inlet of transmission control valve |
| 21 | 244451A1 | 1 | SWITCH, PRESSURE, transmission system pressure, located on the PTO valve, transmission serial |
| 22 | A186005 | 1 | SENSOR, tractor speed |
| 23 | 238-5115 | 2 | O-RING, -115, 70 Duro, .674″ ID x .103″ Thk |
| 24 | 193855A2 | 1 | GAUGE, FUEL, SENSOR – auxiliary fuel tank level |
| 25 | 92261C1 | 1 | HARNESS, sender, auxiliary fuel level |
| 28 | 1958159C2 | 1 | VALVE, SOLENOID, ASSEMBLY – drive, creeper |
| 30 | 1957801C1 | 1 | SWITCH, PRESSURE, pressure, filter pressure |
| 31 | A186004 | 1 | SENSOR, engine rpm |
| 41 | 1546463C1 | 1 | PRESSURE SWITCH, flow compensated (PFC) |
| 42 | 221545A1 | 1 | SWITCH, KIT – implement status, includes lift switch and associated parts, plus instructions, as an |
| 43 | 221546A1 | 1 | HARNESS, extension, 30 foot, used with 221545A1 implement status switch kit on models with trailing |
| 17 | 237-6006 | 1 | O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk |
| 1 | 1964584C1 | 1 | HARNESS, fender, Includes: Ref. 2, 3 |
| 2 | 121645C1 | 1 | SOCKET/RECEPTACLE, covered, 7 pin |
| 3 | 481849C1 | 1 | COVER, PROTECTIVE, BOOT – wiring harness |
| 7 | 1546476C1 | 2 | LAMP, ASSEMBLY – tail, see Figure 4-38 |
| 10 | 102590A1 | 1 | SUPPORT ASSY., auxiliary outlet |
| 11 | 1287737C1 | 2 | SCREW, BOLT – hex, 10 x 25 mm class 10.9, support |
| 12 | 825-1410 | 2 | NUT, M10, Cl 8 |
| 13 | 614-8020 | 2 | BOLT, Hex, M8 x 20, 8.8 |
| 14 | 825-2408 | 2 | NUT, M8 x 1.25, Flg, Cl 8 |
| 15 | 362123R1 | 6 | CLIP, harness retaining |
| 16 | 97212C1 | 4 | SCREW, pan head, No. 6-20 x 7/8 inch |
| 18 | 121646C1 | 1 | CONNECTOR, male, 7 pin, if used |
| 17 | 895-11008 | 2 | WASHER, M8 x 16 x 1.6 |
| 1 | 140646A1 | 1 | HARNESS, headliner, used with oval speakers, requires item 28, adapter harness |
| 1 | 198242A3 | 1 | HARNESS, headliner, used with round speakers |
| 2 | 92185C1 | 2 | LIGHT ASSY., LAMP ASSEMBLY – warning, flasher, parts list Figure 4-38 |
| 3 | 83882C91 | 1 | LAMP, ASSEMBLY – console illumination, parts list Figure 4-42 |
| 4 | 1983391C1 | 1 | LAMP, ASSEMBLY – dome, parts list Figure 4-42 |
| 6 | 122579A1 | 1 | SWITCH, PRESSURE, low pressure, air conditioning |
| 7 | A186256 | 1 | WIPER MOTOR, 12 volt, windshield, see Figure 4-48 |
| 11 | 1977350C1 | 1 | COVER, switch, door |
| 12 | 136893A1 | 1 | SWITCH, door, dome lamp |
| 13 | 92115C2 | 1 | SWITCH, wiper, windshield |
| 14 | 92100C2 | 1 | SWITCH, blower |
| 15 | 92101C1 | 1 | SWITCH, thermostat |
| 16 | 1964672C1 | 1 | LIGHT, indicator, amber, 14 volt, air conditioning shut down |
| 17 | F93209 | 1 | WIPER MOTOR, ASSEMBLY – wiper, rear, see Figure 4-50 |
| 22 | 22-824 | 2 | STRAP, CABLE, 3/16″ x 7 1/4″ |
| 23 | 97249C1 | 2 | CLIP, CLAMP – harness |
| 24 | 104033C2 | 3 | SCREW, SELF TAPPING, Cross Wash Hd, M4.8 x 19, Coated, self-tapping, truss head, No. 10-16 x |
| 26 | 182721A2 | 2 | SPEAKER, radio, 5-1/4 inch, round |
| 27 | 97039C1 | 1 | GROMMET, windshield upper channel |
| 28 | 195551A1 | 1 | HARNESS, adapter, speakers to headliner harness |
| 29 | 362123R1 | 4 | CLIP, harness |
| 1 | 1987421C1 | 1 | HARNESS, rear, headliner |
| 2 | 92185C1 | 2 | LIGHT ASSY., LAMP ASSEMBLY – warning, flasher, parts list Figure 4-38 |
| 3 | 1977564C2 | 1 | BLOWER, cab, component parts not serviced separately |
| 4 | 1343938C2 | 1 | RESISTOR, blower, also order connector 255057C1 and terminal 1120922C1 |
| 7 | 97006C1 | 4 | BOLT, BOLT – hex flange, special, 6 – 1 x 20 mm, self-locking, 6 x 20 mm |
| 8 | 97005C1 | 4 | NUT, hex flange, self-locking, special, 6 mm – 1 |
| 10 | 240877A1 | 1 | SUPPORT, blower |
| 11 | 231-5144 | 10 | NUT, Flg, USR, 1/4″-20 |
| 12 | 117975 | 1 | GROMMET, 5/8″ ID x 1 3/8″ x .062″, Diag Cut, rubber, for 5/8 inch diameter hole |
| 13 | 362120R1 | 3 | CLAMP, CLAMP – P-type |
| 14 | 254252A1 | 2 | CLIP, ELECTRICAL, harness |
| 1 | 251138A2 | 1 | VALVE, ASSEMBLY – hitch control, parts list Figure 8-38 |