CASE IH Magnum tractor 8940

      No Comments on CASE IH Magnum tractor 8940

CASE IH Magnum tractor 8940 — parts list, part 2 of 4

Assemblies on this page: Parts list (continued) … Parts list (continued).

Parts list (continued)

Pos Part no. Qty Description
2 114255A2 2 POTENTIOMETER, GAUGE – position
3 515-23127 1 CLAMP, 1/2″, Insul, 3/8″ Bolt, P-type, 1/2 inch ID
4 614-8016 3 BOLT, Hex, M8 x 16, 8.8
5 892-11008 1 WASHER, LOCK, M8
6 1348212C1 1 SHAFT, potentiometer sensor
7 A164914 2 BUSHING, sensor
8 A162622 1 COUPLING, FLEXIBLE
9 238-5012 1 O-RING, -012, 70 Duro, .364″ ID x .070″ Thk
10 100-3350 1 RING, LOCKING, #50, .392″ Dia, E-Type
11 1960765C2 2 GROMMET, harness, Part of Control Draft Kit P/N 296784A1
12 1348057C1 2 TUBE, harness, Part of Control Draft Kit P/N 296784A1
13 614-10020 2 BOLT, Hex, M10 x 20, 8.8, Full Thd, , Part of Control Draft Kit P/N 296784A1
14 235009A2 1 HARNESS, hitch control, rear chassis
15 1964916C3 2 PIN, LARGE, lower link, hitch sensing, no longer available, order 346350A1 kit below
16 205-61 1 BUTTON, HOLE PLUG, 1 1/2″, button, 1-1/2 inch (without hitch)
17 133738A1 2 CLIP, CLAMP – P-type
18 22-611 1 CLIP, ELECTRICAL, CLAMP – harness
19 413-510 2 BOLT, Hex, 5/16″-18 x 5/8″, G5, Full Thd
20 413-68 1 BOLT, Hex, 3/8″-16 x 1/2″, G5, Full Thd
21 296781A1 2 CONNECTOR, 3 pin (without draft sensing)
22 346350A1 2 SET OF PARTS, KIT – service, draft sensing pin, Includes: Ref. 23, 24, Part of Control Draft Kit P/N
23 1960223C1 2 BUSHING, lower link, Part of Control Draft Kit P/N 296784A1
3 A48889 1 SUPPORT, SOCKET – bulb
4 A48888 1 BULB, BULB – lamp, instrument
8 1971376C1 4 SCREW, SELF TAPPING, Cross Pan Hd, #10 x 1″, self-tapping, pan Phillips, No. 10-16 x 1 inch
1 1964622C3 1 PLATE ASSY., mounting
2 825-1406 7 NUT, M6, Cl 8
4 225-14110 4 NUT, #10-24
5 495-31022 5 WASHER, #10
17 896-11006 2 WASHER, M6 x 13 x 2, HT
19 825-1406 2 NUT, M6, Cl 8
22 107655C1 1 SWITCH, SOLENOID, SWITCH – magnetic, cab solenoid, power
23 614-6025 2 BOLT, Hex, M6 x 25, 8.8, BOLT – hex, full threads, 6 – 1.0 x 25 mm
24 829-1306 2 NUT, M6, Cl 10
25 91954C1 1 SUPPORT, BRACKET – mounting, circuit breaker
28 495-11028 2 WASHER, 1/4″, SAE, flat, 9/32 x 5/8 x 1/16 inch
29 492-11025 2 WASHER, LOCK, 1/4″
30 425-104 2 NUT, 1/4″-20, G5
31 245761C1 1 CIRCUIT BREAKER, 10 ampere
31 245762C1 1 CIRCUIT BREAKER, 15 ampere
31 245763C1 2 CIRCUIT BREAKER, 20 ampere
31 245765C1 4 CIRCUIT BREAKER, 30 ampere
32 245861C1 1 BAR, breaker bus
33 245862C1 1 BAR, buss, 4 hole
34 178148A1 1 COVER, solenoid switch
35 183038A1 1 SWITCH, SOLENOID, SWITCH – with cover, ignition
36 492-11010 1 WASHER, LOCK, #10
37 225-14210 1 NUT, #10-32
38 492-11031 2 WASHER, LOCK, 5/16″, If used, may be replaced by item 41
39 425-105 2 NUT, 5/16″-18, G5, If used, may be replaced by item 41
40 L18337 2 STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch
41 231-5145 2 NUT, Flg, USR, 5/16″-18, Replaces lock washer and nut, items 38 and 39, used on some models
1 468647C2 1 BLOCK ASSY., junction, power and ground
2 1964561C1 1 BAR, junction block buss
3 413-416 2 BOLT, Hex, 1/4″-20 x 1″, G5
4 492-11025 2 WASHER, LOCK, 1/4″
5 425-104 2 NUT, 1/4″-20, G5
8 614-6020 2 BOLT, Hex, M6 x 20, 8.8, Full threads
9 896-11006 2 WASHER, M6 x 13 x 2, HT
10 892-11006 2 WASHER, LOCK, M6
11 829-1306 2 NUT, M6, Cl 10
12 895-18010 1 WASHER, M10 x 18 x 1.6
13 492-11038 1 WASHER, LOCK, 3/8″
14 425-146 2 NUT, Jam, 3/8″-16, G5, hex, jam, 3/8 inch NC
1 1955202C1 1 ELECTRICAL CABINET, BOX – battery
2 96867C2 1 SPACER, upper, box mounting
3 96868C2 1 SPACER, lower, box mounting
4 814-10060 2 BOLT, Hex, M10 x 60, 8.8, Battery box to transmission control valve
5 96636C1 1 SUPPORT, box, rear
6 813-16060 2 BOLT, Hex, M16 x 60, 8.8, Full Thd, Bolt, Hex, M16 x 60, 8.8, Full Thd
7 896-11016 2 WASHER, M17.5 x 30 x 4, HT
8 895-11012 2 WASHER, M12 x 24 x 2.5, flat, 13.5 x 24 x 2.5 mm
9 829-1412 2 NUT, M12, Cl 10
12 96656C1 1 COVER, battery, top
13 1975782C1 2 SCREW, SELF TAPPING, Cross Truss Wash Hd, #10 x 5/8″
14 104036C1 2 NUT, special, top cover
15 96657C2 1 COVER, battery box, front
17 1334657C1 1 PLATE, LARGE, cover, if used
18 1960750C1 6 SCREW, special, 1/4 NC x 3/8 inch
19 231-5144 6 NUT, Flg, USR, 1/4″-20
22 BMF31G 2 BATTERY, DRY, 12V, Electrical supply
23 96635C1 2 ANGLE, BRACKET – hold down, battery
24 97052C1 4 TRUSS ROD, BOLT – hold down, battery
25 231-5145 4 NUT, Flg, USR, 5/16″-18
28 1983286C1 2 CABLE, negative, battery
29 1983630C1 1 TERMINAL CONNECTOR, jump start stud
30 1987379C1 1 CABLE, positive, battery
31 1983285C1 1 CABLE, positive, battery
33 1978410C1 1 MOLDING, TRIM – edge, battery box
34 413-624 1 BOLT, Hex, 3/8″-16 x 1 1/2″, G5
35 492-11038 1 WASHER, LOCK, 3/8″
36 425-106 1 NUT, 3/8″-16, G5
1 1955202C1 1 ELECTRICAL CABINET, BOX – battery
2 96867C2 1 SPACER, upper, box mounting
3 96868C2 1 SPACER, lower, box mounting
4 814-10060 2 BOLT, Hex, M10 x 60, 8.8, Battery box to transmission control valve
5 96636C1 1 SUPPORT, box, rear
6 813-16060 2 BOLT, Hex, M16 x 60, 8.8, Full Thd, Bolt, Hex, M16 x 60, 8.8, Full Thd
7 896-11016 2 WASHER, M17.5 x 30 x 4, HT
8 895-11012 2 WASHER, M12 x 24 x 2.5, flat, 13.5 x 24 x 2.5 mm
9 829-1412 2 NUT, M12, Cl 10
12 96656C1 1 COVER, battery, top
13 1975782C1 2 SCREW, SELF TAPPING, Cross Truss Wash Hd, #10 x 5/8″
14 104036C1 2 NUT, special, top cover
15 96657C2 1 COVER, battery box, front
17 1334657C1 1 PLATE, LARGE, cover, if used
18 1960750C1 6 SCREW, special, 1/4 NC x 3/8 inch
19 231-5144 6 NUT, Flg, USR, 1/4″-20
22 BMF31G 2 BATTERY, DRY, 12V, Electrical supply
23 96635C1 2 ANGLE, BRACKET – hold down, battery
24 97052C1 4 TRUSS ROD, BOLT – hold down, battery
25 231-5145 4 NUT, Flg, USR, 5/16″-18
28 1983286C1 2 CABLE, negative, battery
29 1983630C1 1 TERMINAL CONNECTOR, jump start stud
30 277745A1 1 CABLE, positive, battery
31 277768A1 1 CABLE, cab power
33 1978410C1 1 MOLDING, TRIM – edge, battery box
34 413-624 1 BOLT, Hex, 3/8″-16 x 1 1/2″, G5
35 492-11038 1 WASHER, LOCK, 3/8″
36 425-106 1 NUT, 3/8″-16, G5
1 A187728 1 MOTOR, STARTER, ASSEMBLY – engine, parts list Figure 4-32, See Figure 4-31A for starter
4 493-21052 1 WASHER, LOCK, Int Tooth, 1/2″, internal tooth lock, 1/2 inch, battery terminal, starter mounting Prior
5 425-148 1 NUT, Jam, 1/2″-13, G5, Starter mounting Prior to P.I.N. JJA0076314
6 193-1000 1 NUT, Keps, w/LW,#10-32, hex, with external tooth lock washer, No. 10 NF, switch terminal, starter
7 868-12040 3 SCREW, 12 pt, Flg Hd, M12 x 40, 12.9, BOLT – 12 point flange, 12 – 1.75 x 40 mm, class 12.9, starter
8 896-11012 3 WASHER, M13.5 x 24.5 x 3, HT, Starter mounting Prior to P.I.N. JJA0076314
12 91448C2 1 ALTERNATOR, ASSEMBLY – engine, 110 ampere, parts list Figure 4-36, alternator mounting
13 A189616 1 PULLEY, alternator, mounting
14 J911485 1 SUPPORT, BRACE – alternator, mounting
15 614-8030 1 BOLT, Hex, M8 x 30, 8.8, Full Thd, Brace to engine, Alternator mounting
16 854-12060 1 BOLT, Hex Flg, M12 x 60, 10.9, Alternator mounting
17 854-12050 1 BOLT, Hex Flg, M12 x 50, 10.9, Alternator mounting
18 829-2312 2 NUT, M12 x 1.75, Flg, Cl 10, hex flange, 12 mm – 1.75, class 10, alternator mounting
20 426-820 1 BOLT, Hex, 1/2″-13 x 1 1/4″, G8, Full Thd, BOLT – hex, 1/2 NC x 1-1/4 inch, grade 8, alternator
26 892-11005 4 WASHER, LOCK, M5, Alternator mounting
27 824-1405 4 NUT, M5, Cl 5, Alternator mounting
28 1968023C1 1 PROTECTOR, SHIELD – alternator, mounting
30 492-11044 1 WASHER, LOCK, 7/16″, Alternator mounting
31 825-1404 1 NUT, M4, Cl 8, Alternator mounting
32 892-11004 1 WASHER, LOCK, M4, Alternator mounting
33 425-147 1 NUT, Jam, 7/16″-14, G5, hex, jam, 7/16 inch NC, alternator mounting
1 193432A1 1 MOTOR, STARTER, ASSEMBLY – engine, parts list Figure 4-35A
2 868-12040 3 SCREW, 12 pt, Flg Hd, M12 x 40, 12.9, BOLT – 12 point flange, 12 – 1.75 x 40 mm, class 12.9
3 896-11012 3 WASHER, M13.5 x 24.5 x 3, HT, Replaces 892-11012 washer
4 829-1412 1 NUT, M12, Cl 10
5 892-11012 1 WASHER, LOCK, M12
6 258820A1 1 SCREW, special, 5 x 8 mm
7 892-11005 1 WASHER, LOCK, M5
1 A187851 1 HOUSING, FRAME ASSEMBLY – end, commutator, Includes: Ref. 2, 3
4 845-6060 4 BOLT, Hex Flg, M6 x 60, 8.8, BOLT – heavy hex flange, 6 – 1.0 x 60 mm
5 825-2306 2 NUT, M6 x 1, Flg, Cl 8, hex flange, 6 mm – 1
8 A187857 4 O-RING, sealing
13 A187852 1 BRUSH HOLDER, HOLDER ASSEMBLY – brush, Includes: Ref. 14
14 A187823 4 SPRING, brush
15 A187794 4 BRUSH, starter
16 A47816 4 SCREW, slotted, includes lock washer, 5 – 0.8 x 12 mm
65 814-6040 2 BOLT, Hex, M6 x 40, 8.8
17 A47813 1 WASHER, end, armature
18 A187847 1 ARMATURE, starter
22 A187846 1 HOUSING ASSY., field coil, Includes: Ref. 23-33
34 A187862 1 NUT, hex, terminal
35 A187858 1 FITTING, CONNECTOR – terminal B
38 A187859 1 WASHER, wave
39 425-108 1 NUT, 1/2″-13, G5
41 A187860 1 WASHER, plate, armature
42 A187850 1 HOUSING, ASSEMBLY – lever, Includes: Ref. 43, 44
48 A187865 1 KIT, pin, lever, Includes: Ref. 49, 50, 51
53 A187861 4 SCREW, BOLT – hex, 7 x 23 mm, housing
54 A187848 1 CLUTCH ASSEMBLY, starter drive
55 A187855 1 NUT, pinion stop
58 A47790 1 SNAP RING, collar to shaft
59 A187853 1 LEVER, ASSEMBLY – clutch, starter, Includes: Ref. 60
60 A187854 2 PAD, WEAR, lever
61 A47786 1 O-RING, clutch housing
62 A187849 1 HOUSING, ASSEMBLY – clutch drive, Includes: Ref. 63
64 A187856 6 SCREW, BOLT – hex, special, drive housing
66 A187864 1 COVER, KIT – cover, anti-bypass start, Includes: Ref. 67
68 A187863 1 SWITCH, SOLENOID, ASSEMBLY – magnetic, Includes: All Ref. No. Below
37 829-1410 1 NUT, M10, Cl 10
1 258884A1 1 YOKE, HOUSING – field coil
2 258885A1 1 ARMATURE, ASSEMBLY – starter, Includes: Ref. 2A, 2B
3 258840A1 1 CLUTCH ASSEMBLY, starter
9 258841A1 1 HOUSING, starter
11 258871A1 1 KIT, SERVICE, terminal, M
12 258869A1 1 KIT, SERVICE, terminal, B+
13 258874A1 1 PLUNGER, magnetic switch
16 258877A1 1 TERMINAL CONNECTOR, solenoid
17 141353A1 1 BUSHING, drain
18 A49806 1 BRUSH HOLDER, ASSEMBLY, Includes: Ref. 19
20 258880A1 1 FRAME, starter end
21 211-1311 1 BALL, 11/32″ Dia, chrome alloy steel, grade 200
22 A47232 1 SPRING, compression, 2-13/16 inch free length
23 A49810 1 GEAR, pinion idler
24 A47235 5 ROLLER, pinion bearing
25 A47236 1 RETAINER, roller bearing
26 A49805 1 COVER, terminal
27 104594A1 1 BOLT, hex flange, 144 mm long
28 104593A1 1 BOLT, hex flange, 206 mm long
30 829-1412 1 NUT, M12, Cl 10
31 141360A1 1 RETAINER, WASHER – flat
32 892-11012 1 WASHER, LOCK, M12
33 298253A1 2 RIM, starter, replaces A49812 seal
34 A49809 1 PINION, GEAR –
35 141361A1 4 SCREW, special
36 A49807 2 BRUSH, starter
37 A49808 2 BRUSH, starter
38 258820A1 1 SCREW, special, 5 x 8 mm
39 258883A1 1 BUSHING, drain
40 829-1412 1 NUT, M12, Cl 10
41 1546500C1 1 SEAL, 47 ID x 2.4 mm wide, housing
42 495-81252 3 WASHER, #12, (Flat, 1/4″ x 9/16″ x 1/16″)
43 A47130 3 O-RING, bolt seal
44 A47129 3 BOLT, ASSEMBLY – with washer
45 892-11005 1 WASHER, LOCK, M5
1 1964731C1 1 HOUSING, collector ring end
3 1964737C1 1 BUSHING, expansion
4 3079389R1 1 CAPACITOR, suppression
5 684857C1 1 SCREW, fillister head, capacitor retaining
6 A186196 1 WASHER, special
9 111899A1 1 REGULATOR, voltage
10 3079394R91 1 SET, BRUSHES
11 1964734C1 2 SPRING, compression
12 A186194 2 SCREW, Sltd Truss Hd, M4 x 18, w/LW, BOLT – hex flange, special, regulator
13 1964738C1 1 KIT, REPAIR, KIT – terminal hardware
15 1546477C1 1 SLEEVE, RING – sleeve, housing ball bearing
16 1964732C1 1 RECTIFIER, alternator
17 A187504 2 SCREW, hex flange, special, rectifier bridge
18 1964735C1 1 STATOR, alternator
19 1964728C1 1 ROTOR, alternator
20 3079410R1 1 RING, collector
21 1964730C1 1 BEARING, BALL
22 495-51066 1 WASHER, 9/16″ x 1 1/4″ x .1″, flat, 21/32 x 1-1/4 x 3/32 inch
23 231-46010 1 NUT, LOCK, 5/8″-11, GB
26 1964727C1 1 PLATE, bearing retaining
27 1964726C1 1 BEARING, BALL, drive end
28 1964725C1 1 HOUSING, drive end
29 1964748C1 4 SCREW, BOLT – fillister head, special, alternator
30 1964750C1 4 SCREW, machine, flat head, special, retaining
31 1964729C1 1 SPACER, ring
32 1964736C1 1 FAN, alternator
34 A189616 1 PULLEY, alternator
1 91971C2 1 LAMP, ASSEMBLY – head, left
1 91972C2 1 LAMP, ASSEMBLY – head, right, shown, Includes: Ref. 2-7A
3 1964759C1 1 COVER ASSY, access, head lamp
4 91967C1 1 BULB, lamp, H4, head lamp
5 92242C1 1 BULB, lamp, H3, head lamp
6 1964757C1 1 SUPPORT, HOLDER – bulb, H3, head lamp
7 1964758C1 1 SPRING, holder, bulb, head lamp
8 495-11028 6 WASHER, 1/4″, SAE, flat, 9/32 x 5/8 x 1/16 inch, head lamp
9 492-11025 6 WASHER, LOCK, 1/4″, Head lamp
10 425-104 6 NUT, 1/4″-20, G5, Head lamp
15 92185C1 4 LIGHT ASSY., LAMP – warning, flasher, assembly, Includes: Ref.16, 17, 18
16 130883C1 1 LENS, amber, warning lamp, flasher assembly
18 A41264 1 BULB, #1156, 12V, Flasher warning lamp, assembly
20 1974614C2 8 SCREW, SELF TAPPING, Cross Pan Hd, #10-24 x 2 1/4″, Special, Flasher Warning Lamp Assy
22 1546476C1 2 LAMP, ASSEMBLY – tail, not available for service, order items 23-31, tail lamp, Includes: Ref. 23-31
23 A186202 2 LAMP, ASSEMBLY – tail, lamp, Includes: Ref.24, 25, 26
25 A186201 1 CABLE PULLING GRIP, HARNESS – includes socket, tail lamp, assembly
26 D71346 1 LAMP, TAIL, lamp, No. 168, tail lamp, assembly
28 1283837C1 1 HOUSING, tail lamp, purchase separately, assembly
31 1327506C1 4 SCREW, SELF TAPPING, Cross Pan Hd, M4.8 x 19, Coated, Tail lamp, assembly
32 253419A1 4 SCREW, Hex Wash Hd, #8-18 x 5/8″, hex washer, No. 8 – 18 x 5/8 inch, special, replaces 220408A1
1 92266C2 1 HEADLIGHT, LAMP ASSEMBLY – flood, left, Includes: Ref. 2-7
2 1964807C1 1 LAMP BASE, LENS – reflector, lamp, standard glass, if used, lower front flood
2 276498A1 1 LENS, refector, lamp, tempered glass, if used, lower front flood, Includes: Ref. 3
4 1312210C2 1 BULB, lamp, Halogen, replaces 1312210C1 bulb, lower front flood
5 1964806C1 1 BEZEL, HOUSING – lamp, front, lower flood
6 260-54312 2 SCREW, SELF TAPPING, Cross Pan Hd, #6 x 3/4″, If used, lower front flood lamp
9 892-11010 1 WASHER, LOCK, M10, Lower front flood lamp
10 825-1410 1 NUT, M10, Cl 8, Lower front flood lamp
11 96901C1 1 GROMMET, blower motor wire, lamp wiring, lower front flood lamp
12 1334607C2 1 BRACKET, mounting, flood lamp, lower front
13 1960750C1 3 SCREW, special, 1/4 NC x 3/8 inch, lower front flood lamp
14 1334650C1 3 SHOCK ABSORBER, MOUNT – rubber, lower front flood lamp
15 231-5144 3 NUT, Flg, USR, 1/4″-20, Lower front flood lamp
19 92269C1 1 LAMP, WORK, ASSEMBLY – flood, fender lamp assembly, Includes: Ref. 20-28
20 260-54312 2 SCREW, SELF TAPPING, Cross Pan Hd, #6 x 3/4″, Fender flood lamp, assembly
20 340-1256 2 SCREW, Cross Pan Hd, 1/4″-20 x 3/8″, machine, pan Phillips, 1/4 NC x 3/8 inch, if used, fender flood
22 1312210C2 1 BULB, lamp, Halogen, replaces 1312210C1 bulb, fender flood, assembly
23 1964807C1 1 LAMP BASE, LENS – reflector, lamp, fender flood, assembly, Includes: Ref. 24
25 1964806C1 1 BEZEL, HOUSING – lamp, front, fender flood, assembly
26 A187915 1 BRACKET, mounting, lamp, fender flood, assembly
27 814-8045 1 BOLT, Hex, M8 x 45, 8.8, Fender flood lamp, assembly
28 832-41308 1 NUT, M8 x 1.25, Cl 10, hex, self-locking, 8 mm – 1.25, class 10.9, fender flood lamp, assembly
29 96901C1 1 GROMMET, blower motor wire, lamp wiring, fender flood, assembly
30 495-81140 1 WASHER, 13/32″ x 1 1/4″ x .060″, If used, fender flood lamp, assembly
31 892-11010 1 WASHER, LOCK, M10, Fender flood lamp, assembly
32 825-1410 1 NUT, M10, Cl 8, Fender flood lamp, assembly
8 895-15010 1 WASHER, M11 x 24 x 2, If Used, Lower front flood lamp
30 895-15010 1 WASHER, M11 x 24 x 2, If Used, Fender flood lamp, assembly
3 107329C1 1 HARNESS, WIRE, AND CABLE – bulb, console lamp
4 D71346 1 LAMP, TAIL, lamp, No. 168, console lamp
5 1327506C1 2 SCREW, SELF TAPPING, Cross Pan Hd, M4.8 x 19, Coated, Console lamp
7 1983391C1 1 LAMP, dome, cab lamp assembly, Includes: Ref. 8
8 E35556 1 BULB, BULB – dome, cab lamp assembly
10 92269C1 2 LAMP, WORK, ASSEMBLY – flood, with standard glass lens, includes items 11 – 18 below, cab lamp
10 344649A1 2 LIGHT, WORK, ASSEMBLY – flood, with tempered glass lens, cab lamp assembly, Includes: Ref. 11-18
11 1964807C1 1 LAMP BASE, LENS – reflector, lamp, standard glass, if used, flood, cab assembly
11 276498A1 1 LENS, reflector, lamp, tempered glass, if used, flood, cab assembly
12 1964806C1 1 BEZEL, HOUSING – lamp, front, flood, cab assembly
13 260-54312 2 SCREW, SELF TAPPING, Cross Pan Hd, #6 x 3/4″, If used, flood lamp, cab assembly
13 340-1256 2 SCREW, Cross Pan Hd, 1/4″-20 x 3/8″, machine, pan Phillips, 1/4 NC x 3/8 inch, if used, flood lamp
15 1312210C2 1 BULB, lamp, Halogen, flood, cab assembly
16 A187915 1 BRACKET, mounting, lamp, flood, cab assembly
17 814-8045 1 BOLT, Hex, M8 x 45, 8.8, Flood lamp, cab assembly
18 832-41308 1 NUT, M8 x 1.25, Cl 10, hex, self-locking, 8 mm – 1.25, class 10.9, flood lamp, cab assembly
19 495-81140 2 WASHER, 13/32″ x 1 1/4″ x .060″, Flood lamp, cab assembly
20 892-11010 2 WASHER, LOCK, M10, Flood lamp, cab assembly
21 825-1410 2 NUT, M10, Cl 8, Flood lamp, cab assembly
22 96901C1 2 GROMMET, blower motor wire, lamp wiring, flood lamp, cab assembly
1 228760A1 1 RADAR, SENSOR – speed, ground, new
4 L18337 3 STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch, nylon
7 814-6100 4 BOLT, Hex, M6 x 100, 8.8
9 248550A1 1 SUPPORT, BRACKET – mounting, speed sensor
10 614-10020 2 BOLT, Hex, M10 x 20, 8.8, Full Thd
13 495-11028 4 WASHER, 1/4″, SAE, flat, 9/32 x 5/8 x 1/16 inch
14 825-5146 4 NUT, M6, Flg Ser
12 895-11010 1 WASHER, M10 x 20 x 2
1 141950A2 1 RADIO, AM-FM stereo, order ZAE1000 radio from Machinery Price List
1 141951A2 1 RADIO, AM-FM stereo, with cassette tape player, order ZAE3000 from Machinery Price List
2 97127C3 1 SUPPORT ASSY., radio
3 1327506C1 2 SCREW, SELF TAPPING, Cross Pan Hd, M4.8 x 19, Coated
6 191842A2 1 ANTENNA, ASSEMBLY – radio, includes base, mast, cable, and hardware, with 90 degree antenna
7 253420A1 1 SUPPORT, PLATE – mounting, antenna
20 1964958C1 1 KIT, radio support, Includes: Ref. 21-24
25 1987508C1 1 SUPPRESSOR, blower frequency
26 1987509C1 1 SUPPRESSOR, wiper frequency
27 182721A2 2 SPEAKER, radio, 5-1/4 inch, round, mounts in rear headliner
28 363-30812 8 SCREW, Hex Wash Hd, #8-32 x 3/4″, machine, hex washer head, No. 8 NC x 3/4 inch
29 195551A1 2 HARNESS, adapter, speakers to headliner harness
1 A186256 1 WIPER MOTOR, 12 volt
3 N8359 1 SUPPORT, BRACKET – windshield wiper assembly
4 N8362 3 SCREW, Hex, M6 x 18.5, Spc, w/LW, with washer, special
5 N8360 1 SUPPORT, ARM – drive
6 N8361 1 WASHER, Belleville
7 L112090 1 NUT, hex, special
10 N8358 1 ROD, LINK – wiper, pivot
11 N8356 1 SCREW, Flat Cross Csk Hd, M5 x 8, special, bracket
12 N14112 1 SHAFT, pivot, wiper
13 L112089 1 WASHER, wave, special
14 L112081 1 CAP, pivot shaft end
15 825-1408 1 NUT, M8, Cl 8
17 A186222 1 WIPER ARM, front, 475 mm (18-3/4 inch) long
18 132024A1 1 WIPER BLADE, arm, complete
18 132025A1 1 WIPER BLADE, rubber, 500 mm long, windshield wiper refill
19 414-410 2 BOLT, Hex, 1/4″-28 x 5/8″, G5, Full Thd, BOLT – hex, 1/4 NF x 5/8 inch, wiper braket mounting, not
1 F93209 1 WIPER MOTOR, ASSEMBLY –
4 D74631 1 NUT, hex, 5/8 inch – 24 extra fine thread
5 A165073 1 WASHER, nylon, 5/8 x 1-1/2 x 7/64 inch
6 A165074 1 SPACER, SPACER – nylon, 7/8 inch OD
7 F64198 1 SPACER, SPACER – nylon, black, motor mounting
8 142-102 1 SCREW, Cross Oval Hd, #10-24 x 3/4″, machine, oval Phillips, No. 10 NC x 3/4 inch
9 A165076 1 WASHER, nylon, 5/16 x 1 x 7/64 inch
10 230-42409 1 NUT, LOCK, #10-24, GA, hex, self-locking, No. 10 NC
11 D78019 1 WIPER ARM, blade, 12 inch
12 A42580 1 BLADE, WIPER, arm, rear, 406 mm (16 inch) long
13 170-105 1 SCREW, Sltd Pan Hd, #5-40 x 1/2″, machine, pan head slotted, No. 5 NC x 1/2 inch
14 225-14105 1 NUT, #5-40, Blade attaching
1 240556A1 1 SUPPORT, BRACKET – mounting, windshield washer reservoir and pump
5 K304596 1 RESERVOIR, AND PUMP ASSEMBLY – washer fluid, component parts not serviced separately
8 1968057C1 1 HOSE, TUBING – washer, 4 inch (100 mm) long (See Note)
9 K307050 1 VALVE, non-return
10 1968058C1 1 HOSE, TUBING – washer, 141-3/4 inch (3600 mm) long (See Note)
11 L18337 9 STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch, harness
12 1964673C1 1 HARNESS, wiring, washer pump
19 1968053C1 1 ELBOW, ELBOW – 90 degree, special, mounts to 1968052C1 bracket, item 32
20 N8361 1 WASHER, Belleville
21 825-1408 1 NUT, M8, Cl 8
24 1968059C1 1 HOSE, TUBING – washer, 19-11/16 inch (500 mm) long (See Note)
25 1968054C1 1 JET, NOZZLE – windshield washer
30 1968129C1 1 FITTING, TEE – nylon, barb ends (Converting for rear washer)
31 1968130C1 2 CLIP, nozzle (Converting for rear washer)
32 1968052C1 1 BRACKET, connector, to bulkhead
1 1989917C1 1 HOUSING, support, steering
2 139202A2 1 SHAFT, telescoping
3 148424C2 2 BUSHING, lower, steering tube
4 103985C1 2 BUSHING, upper, steering tube
5 1348393C1 1 O-RING, steering column cap
6 148921C1 1 CAP, column
11 1954245C1 1 SHIELD, outer
12 1954244C1 1 PROTECTOR, SHIELD – inner
14 A65544 1 WHEEL (STEERING)
15 138969A1 1 CAP, KNOB – lock, wheel
17 425-146 1 NUT, Jam, 3/8″-16, G5, hex, jam, 3/8 inch NC
18 100-1187 1 RING, SNAP, #87, Ext
19 228340A1 1 WASHER, rubber, snubber, 7/8 inch ID
22 100-1587 1 RING, SNAP, #87, Ext, Crescent
23 F19646 1 NUT, SPECIAL, 13/16″-20, Thin, lock, steering wheel retaining
24 1342054C1 1 PLASTIC PLUG, INSERT – black
26 1954246C1 1 WASHER, shield
27 1974720C2 1 BOOT, column
28 1975919C1 4 SCREW, special
29 104036C1 4 NUT, expansion
31 104008C1 1 INSULATOR, RUBBER, vibration
32 148431C1 1 JOINT, universal
33 323101A1 2 PIN, LARGE, roll, 9.3 (3/8) OD x 44.5 mm (1-3/4 inch) long, replaces 438-32428 pin
34 148426C2 1 SUPPORT ASSY., column, INCLUDES REFS 35, 36, 37
35 614-8025 2 BOLT, Hex, M8 x 25, 8.8
36 829-1408 2 NUT, M8, Cl 10
37 837-10016 2 DOWEL, M10 x 16, dowel, 10 x 16 mm, hardened
38 614-10035 3 BOLT, Hex, M10 x 35, 8.8, Full Thd
39 496-81003 3 WASHER, 13/32″ x 1 1/16″ x .095″, HDN, flat, 13/32 x 1-1/16 x 3/32 inch, hardened
40 104809C1 3 BUSHING, vibration damper
41 614-10020 2 BOLT, Hex, M10 x 20, 8.8, Full Thd, Without manual shuttle shift
41 614-10050 2 BOLT, Hex, M10 x 50, 8.8, Full Thd, BOLT – hex, full threads, 10 – 1.5 x 50 mm (With manual shuttle
44 148920C1 2 BUSHING, pivot
45 892-11012 2 WASHER, LOCK, M12
46 814-12050 2 BOLT, Hex, M12 x 50, 8.8
47 97109C1 1 LEVER, release, tilt
48 97111C4 1 HANDLE, lever
49 170-101 1 SCREW, Slotted Pan Hd, #8-32 x 5/16″, No. 8 x 5/16 inch
50 96972C1 1 PLATE ASSY., detent, tilt
51 614-8016 2 BOLT, Hex, M8 x 16, 8.8
52 538321R1 1 SPRING, detent
53 148480C1 1 SPRING, support
1 225388A2 1 PUMP, ASSEMBLY – steering, hydrostatic, parts list Figure 5-10
2 1977683C1 1 SEAL ASSY., dust
3 104008C1 1 INSULATOR, RUBBER, vibration
4 1344478C1 1 SUPPORT, BRACKET – mounting, pump
5 413-510 4 BOLT, Hex, 5/16″-18 x 5/8″, G5, Full Thd
6 104809C1 3 BUSHING, vibration damper
7 496-81003 3 WASHER, 13/32″ x 1 1/16″ x .095″, HDN, flat, 13/32 x 1-1/16 x 3/32 inch, hardened
8 614-10035 3 BOLT, Hex, M10 x 35, 8.8, Full Thd
9 201-102 4 CONNECTOR, HYD., 13/16″-16 ORFS x 3/4″-16 ORB, Includes Ref. 10, 11
10 237-6008 1 O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
11 238-6014 1 O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
12 201-303 1 ELBOW, 90є, 9/16″-18 x 7/16″-20 Adj, ORFS, 90 degree, 9/16-18 face seal x 7/16-20 inch adj O-ring
13 237-6004 1 O-RING, 4-1, 90 Duro, .351″ ID x .072″ Thk
14 238-6011 1 O-RING, -011, 90 Duro, .301″ ID x .070″ Thk
15 1334378C1 1 HOSE ASSY., 533 mm (21 inch) long
16 1978481C1 1 PIPE, TUBE – steering supply, upper
17 1342026C2 1 PIPE, SLEEVE – corrugated, bulk, 32 (1-1/4) x 37 (1-7/16) x 565 mm (22-1/4 inch) long
18 1342123C2 1 HOSE, return, 967 mm (38-1/8 inch) long
19 1334592C4 1 PIPE, SLEEVE – corrugated, bulk, 41 (1-5/8) x 49 (1-15/16) x 585 mm (23-1/32 inch) long
20 1542766C1 1 HOSE, steering signal, 650 mm (25-5/8 inch) long
21 1968083C3 1 HOSE, PROTECTION, SLEEVE – corrugated, 940 mm (37 inch) long, cut from 1978484C2 bulk sleeve
22 1978482C1 1 PIPE, TUBE – steering return
23 1978480C2 2 PIPE, TUBE – right and left turn
25 1334208C1 1 HOSE ASSY., 2692 mm (106 inch) long, left turn
26 1976794C1 1 HOSE ASSY., 2108 mm (83 inch) long, right turn
27 1342026C2 2 PIPE, SLEEVE – corrugated, bulk, 32 (1-1/4) x 37 (1-7/16) x 565 mm (22-1/4 inch) long
28 201-101 2 CONNECTOR, HYD., 11/16″-16 ORFS x 9/16″-18 ORB, ADAPTER – straight, 11/16-16 face seal x
29 237-6006 1 O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
30 238-6012 1 O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
35 238-6012 1 O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
36 238-6014 4 O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
38 238-6018 1 O-RING, -018, 90 Duro, .739″ ID x .070″ Thk
39 A169433 1 STRAP, SECURING, tie
1 225390A2 1 PUMP, ASSEMBLY – steering, hydrostatic, parts list Figure 5-12
2 1977683C1 1 SEAL ASSY., dust
3 104008C1 1 INSULATOR, RUBBER, vibration
4 1344478C1 1 SUPPORT, BRACKET – mounting, pump
5 413-510 4 BOLT, Hex, 5/16″-18 x 5/8″, G5, Full Thd
6 104809C1 3 BUSHING, vibration damper
7 496-81003 3 WASHER, 13/32″ x 1 1/16″ x .095″, HDN, flat, 13/32 x 1-1/16 x 3/32 inch, hardened
8 614-10035 3 BOLT, Hex, M10 x 35, 8.8, Full Thd
9 201-102 4 CONNECTOR, HYD., 13/16″-16 ORFS x 3/4″-16 ORB, Includes Ref. 10, 11
10 237-6008 1 O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
11 238-6014 1 O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
12 201-303 1 ELBOW, 90є, 9/16″-18 x 7/16″-20 Adj, ORFS, 90 degree, 9/16-18 face seal x 7/16-20 inch adj O-ring
13 237-6004 1 O-RING, 4-1, 90 Duro, .351″ ID x .072″ Thk
14 238-6011 1 O-RING, -011, 90 Duro, .301″ ID x .070″ Thk
15 1334378C1 1 HOSE ASSY., 533 mm (21 inch) long
16 1978481C1 1 PIPE, TUBE – steering supply, upper
17 1342026C2 1 PIPE, SLEEVE – corrugated, bulk, 32 (1-1/4) x 37 (1-7/16) x 565 mm (22-1/4 inch) long
18 1342123C2 1 HOSE, return, 967 mm (38-1/8 inch) long
19 1334592C4 1 PIPE, SLEEVE – corrugated, bulk, 41 (1-5/8) x 49 (1-15/16) x 585 mm (23-1/32 inch) long
20 1542766C1 1 HOSE, steering signal, 650 mm (25-5/8 inch) long
21 1968083C3 1 HOSE, PROTECTION, SLEEVE – corrugated, 940 mm (37 inch) long, cut from 1978484C2 bulk sleeve
22 1978482C1 1 PIPE, TUBE – steering return
23 1978480C2 2 PIPE, TUBE – right and left turn
25 1976786C1 1 HOSE ASSY., 2515 mm (99 inch) long, right turn
26 1976799C1 1 HOSE ASSY., 2108 mm (83 inch) long, left turn
27 1342026C2 2 PIPE, SLEEVE – corrugated, bulk, 32 (1-1/4) x 37 (1-7/16) x 565 mm (22-1/4 inch) long
28 251324A1 2 HOSE ASSY., crossover, 727 mm (28-5/8 inch) long
29 201-304 2 ELBOW, 90є, 11/16″-16 x 9/16″-18 Adj, ORFS, 90 degree, 11/16-16 face seal x 9/16-18 inch adj
30 237-6006 1 O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
31 238-6012 1 O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
32 201-412 2 TEE, 13/16″-16 x 3/4″-16 Run, ORFS, 13/16-16 face branch x face x 3/4-16 inch adj O-ring, Includes:
33 237-6008 1 O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
34 238-6014 2 O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
35 238-6012 1 O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
36 238-6014 4 O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
38 238-6018 1 O-RING, -018, 90 Duro, .739″ ID x .070″ Thk
39 A169433 1 STRAP, SECURING, tie
1 1994591C4 1 VALVE, ASSEMBLY – priority, steering, parts list Figure 5-14
2 238-6117 1 O-RING, -117, 90 Duro, .799″ ID x .103″ Thk
3 201-308 1 ELBOW, 90є, 1 7/16″-12 x 1 5/8″-12, Adj, ORFS, 90 deg, 1-7/16-12 face x 1-5/16-12 inch adj O-ring
4 237-6016 1 O-RING, 16-1, 90 Duro, 1.171″ ID x .118″ Thk
6 201-307 1 ELBOW, 90є, 1 3/16″-12 x 1 1/16″-12 Adj, ORFS, 90 degree, 1-3/16-12 face seal x 1-1/16-12 inch adj
7 237-6012 1 O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk
8 238-6018 1 O-RING, -018, 90 Duro, .739″ ID x .070″ Thk
9 201-102 1 CONNECTOR, HYD., 13/16″-16 ORFS x 3/4″-16 ORB, Includes Ref. 10, 11
10 237-6008 1 O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
11 238-6014 1 O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
12 201-101 2 CONNECTOR, HYD., 11/16″-16 ORFS x 9/16″-18 ORB, ADAPTER – straight, 11/16-16 face seal x
14 238-6012 1 O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
17 1340547C1 1 TUBE ASSY., supply, steering, Includes: Ref. 19
19 238-6014 1 O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
21 1289489C3 1 TUBE ASSY., steering, signal rear, Includes: Ref. 22
22 238-6012 2 O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
23 1340546C1 1 PIPE, TUBE – steering, signal front, Includes: Ref. 25
25 238-6012 2 O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
29 252478A3 1 TUBE ASSY., pump, signal short, replaces 1289370C2 tube
30 1334536C2 1 CLAMP, 3/8 inch OD tube
31 1334535C2 1 SUPPORT, PLATE – tube
32 614-6012 1 BOLT, Hex, M6 x 12, 8.8
33 201-408 1 TEE, 11/16″-16 ORFS, 11/16-16 inch face seal branch x face seal x face seal, Includes: Ref. 34
34 238-6012 3 O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
37 1340548C3 1 SUPPORT, BRACKET – tube
38 613-10025 2 BOLT, Hex, M10 x 25, 8.8, Full Thd, BOLT – hex, full threads, 10 – 1.5 x 25 mm
40 825-1410 2 NUT, M10, Cl 8
42 614-8020 6 BOLT, Hex, M8 x 20, 8.8
43 825-1408 6 NUT, M8, Cl 8
44 1348408C1 1 CLAMP, tube retaining
45 218-5158 1 PLUG, Hex Hd, 1 1/16″-12 ORB, hex, 1-1/16-12 inch O-ring boss (Without hitch), Includes: Ref. 46
46 237-6012 1 O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk
47 814-10060 1 BOLT, Hex, M10 x 60, 8.8
5 238-6021 1 O-RING, -021, 90 Duro, .926″ ID x .070″ Thk
39 895-11010 2 WASHER, M10 x 20 x 2
13 237-6006 1 O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
10 238-6040 3 O-RING, -040, 90 Duro, 2.864″ ID x .070″ Thk, End cap (Replaces N6392 O-ring), Part of Seal Kit P/N
20 238-6011 1 O-RING, -011, 90 Duro, .301″ ID x .070″ Thk, (Replaces L30893), Part of Seal Kit P/N 1343658C3
22 238-5012 1 O-RING, -012, 70 Duro, .364″ ID x .070″ Thk, , Part of Seal Kit P/N 1343658C3
28 121179A1 1 SEAL, teflon, Part of Seal Kit P/N 1343658C3
31 238-5225 1 O-RING, -225, 70 Duro, 1.859″ ID x .139″ Thk, , Part of Seal Kit P/N 1343658C3
34 18-137 1 SEAL, input, dust, replaces 697494R91 seal, Part of Seal Kit P/N 1343658C3
37 1343647C1 1 HOUSING, COLUMN ASSEMBLY – pump, Includes: Ref. 38
38 1343650C1 4 SCREW, 12 Pt Flg, 3/8″-16 x 1″, G8
10 238-6040 3 O-RING, -040, 90 Duro, 2.864″ ID x .070″ Thk, End cap (Replaces N6392 O-ring), Part of Seal Kit P/N
20 238-6011 1 O-RING, -011, 90 Duro, .301″ ID x .070″ Thk, (Replaces L30893), Part of Seal Kit P/N 1343658C3
22 238-5012 1 O-RING, -012, 70 Duro, .364″ ID x .070″ Thk
28 121179A1 1 SEAL, teflon, Part of Seal Kit P/N 1343658C3
31 238-5225 1 O-RING, -225, 70 Duro, 1.859″ ID x .139″ Thk, , Part of Seal Kit P/N 1343658C3
34 18-137 1 SEAL, input, dust, replaces 697494R91 seal
37 1343647C1 1 HOUSING, COLUMN ASSEMBLY – pump, Includes: Ref. 38
38 1343650C1 4 SCREW, 12 Pt Flg, 3/8″-16 x 1″, G8
1 1978362C1 1 BODY, valve
3 1994566C1 1 PLUG, orifice
5 G108700 1 PLUG, orifice
6 G110111 1 SPRING, VALVE, priority
7 118923A2 1 PLUG, orifice
8 86625138 1 PLUG, Hex Soc, 7/8″-14 ORB, Includes Ref. 9
9 237-6010 1 O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
12 1994580C1 1 PLUG, check
13 1994581C1 1 SPRING, load check
14 G108723 1 RING, backup
15 1543329C1 1 POPPET, VALVE, PLUG –
16 238-6015 1 O-RING, -015, 90 Duro, .551″ ID x .070″ Thk
23 238-6018 1 O-RING, -018, 90 Duro, .739″ ID x .070″ Thk
24 G35540 1 RING, backup
25 238-6012 1 O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
26 237-6012 1 O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk
27 425-1510 1 NUT, Jam, 5/8″-18, G5, Hex
28 G108556 1 POPPET, VALVE, relief
30 G108867 1 PLUG, special adjusting screw
31 G108866 1 HOUSING, BODY – pilot relief
1 1954124C4 1 SLEEVE, HYD CYL, TUBE – cylinder, INCLUDES REF 2
2 1255304C1 2 BUSHING, pivot
3 1255306C5 1 ROD, PISTON
4 238-5139 1 O-RING, -139, 90 Duro, 2.175″ ID x .103″ Thk
5 1255309C1 1 SEAL ASSY., piston
10 119188C1 2 SEAL, piston rod
11 238-5143 2 O-RING, -143, 90 Duro, 2.425″ ID x .103″ Thk
12 1255311C1 2 WASHER, backup
13 1255312C1 2 WIRE, RETAINING, WIRE – retaining, 205 mm (8-1/16 inch) long, cut from 140600C1 bulk wire
14 D95141 2 WIPER, WIPER – piston rod
15 1255310C1 2 CYLINDER HEAD, GLAND – end
16 219-17 2 NIPPLE, LUBE, 3/16″ x .55″ lg, Drive
1 181582A2 1 COOLER, OIL, hydraulic
2 181583A1 1 CONDENSER, air conditioning
3 238-6018 2 O-RING, -018, 90 Duro, .739″ ID x .070″ Thk
4 224497A1 2 PIPE, TUBE – oil cooler to tranmission hoses
5 844-8020 4 BOLT, Hex Flg, M8 x 20, 8.8
6 832-10408 4 NUT, LOCK, M8 x 1.25, Cl 8
7 182351A2 1 SUPPORT, BRACKET – upper, pivot
8 224081A1 1 SUPPORT, BRACKET – lower
10 832-10408 2 NUT, LOCK, M8 x 1.25, Cl 8
11 614-8020 4 BOLT, Hex, M8 x 20, 8.8
12 492-11031 4 WASHER, LOCK, 5/16″
14 413-512 2 BOLT, Hex, 5/16″-18 x 3/4″, G5, Full Thd
15 492-11031 2 WASHER, LOCK, 5/16″
16 495-11034 2 WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch
17 225398A2 1 HOSE, 3340 mm (131-1/2 inch) long, cooler supply
18 225399A2 1 HOSE, 3632 mm (143 inch) long, cooler return
19 238-6018 4 O-RING, -018, 90 Duro, .739″ ID x .070″ Thk
20 1334592C4 1 PIPE, SLEEVE – corrugated, bulk, 41 (1-5/8) x 49 (1-15/16) x 585 mm (23-1/32 inch) long
21 L18337 1 STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch
22 1348391C1 1 TUBE, cooler supply
23 201-104 1 CONNECTOR, HYD., 1 3/16″-12 ORFS x 1 1/16″-12 ORB, Includes Ref. 24, 25
24 238-6012 1 O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
25 238-6018 1 O-RING, -018, 90 Duro, .739″ ID x .070″ Thk
13 895-15008 4 WASHER, M8 x 20 x 1.6
1 30225R1 1 BOLT, Hex, Lock, M12 x 30, Cl 10.9, BOLT – hex, 12 – 1.75 x 30 mm
2 101936C2 1 WASHER, flat, hardened, special
5 196338A1 1 PIN, LARGE, pivot, front axle
6 A177855 2 WASHER, thrust
8 137316A2 1 SUPPORT ASSY., BOLSTER – steering
9 192896A1 4 PLUG, front support, if used
1 189425C1 2 HUB CAP, wheel hub
2 732-6350 2 PIN, SPLIT (COTTER), M6.3 x 50
3 1259683C1 2 NUT, hex, slotted, 30 mm – 1.5
4 896-12030 2 WASHER, M30 x 56.5 x 5, HT, flat, 33 x 56 x 5 mm, hardened
5 130504H 2 BEARING, CONE, tapered roller
7 ST753B 2 BEARING, CONE, tapered roller
10 1259519C2 2 KNUCKLE, STEERING, SPINDLE ASSEMBLY, Includes: Ref. 11, 12
11 491641C1 1 SEAL, front wheel spindle
12 1259522C1 1 SHIELD, dust, front wheel spindle
13 1270815C1 2 BEARING, thrust wheel spindle
14 1264574C2 1 EXTENSION ASSY., AXLE – LH section, Incl. item 15
14 1264575C2 1 EXTENSION ASSY., AXLE – RH section, Incl. Ref. 15
15 1259518C1 2 BUSHING, spindle
16 1259526C2 1 ARM, steering spindle, left-hand
16 1259527C2 1 ARM, STEERING, spindle, right-hand, shown
17 1259669C2 2 WASHER, steering arm retainer
18 614-20055 2 BOLT, Hex, M20 x 55, 8.8, Full Thd
19 219-17 2 NIPPLE, LUBE, 3/16″ x .55″ lg, Drive
22 828-24200 4 BOLT, Hex, M24 x 200, 10.9
23 896-12024 4 WASHER, M24 x 44.5 x 5, HT, flat, 26 x 44 x 5 mm, hardened
24 1264635C1 4 NUT, square, special
25 1289093C2 1 HOUSING, AXLE – center section
26 196294A1 2 BUSHING, front pivot
30 1259528C1 2 HUB, ASSEMBLY – wheel, Includes: Ref. 31, 32, 33
31 1264549C1 1 WASHER, CUP, hub seal
32 29214H 1 BEARING, CUP, tapered roller bearing, 4-5/16 inch OD
33 130503H 1 BEARING, CUP, tapered roller bearing, 3-17/64 inch OD
34 219-404 2 NIPPLE, LUBE, 45є, 3/16″ x .83″ lg, Drive
1 1280657C1 1 TUBE, tie rod
3 1280658C1 1 BALL JOINT, SOCKET ASSEMBLY – tie rod, end, Includes: Ref. 4, 5
4 1280659C1 1 SEAL, dust
5 1280660C1 1 NUT, SLOTTED, hex slotted, 20 mm – 1.50
6 1280661C1 1 NUT, SLOTTED, hex, jam, 1-1/8″ NF
7 1280662C1 1 BALL JOINT, SOCKET ASSEMBLY – tie rod, Includes: Ref. 8, 9
8 1280659C1 1 SEAL, dust
9 1280660C1 1 NUT, SLOTTED, hex slotted, 20 mm – 1.50
10 A145857 4 CLAMP, tie rod
11 328-648 2 BOLT, Hex, 3/8″-24 x 3″, G8
12 232-4616 2 NUT, LOCK, 3/8″-24, GC
13 219-8 2 NIPPLE, LUBE, 1/4″-28 NPT x .54″ lg
14 432-824 4 PIN, SPLIT (COTTER), 1/8″ x 1 1/2″
16 93194C8 1 CYLINDER STEERING, ASSEMBLY – 67 (2-5/8) ID x 246 mm (9-3/4 inch), parts list Figure 5-16
19 413-732 1 BOLT, Hex, 7/16″-14 x 2″, G5, BOLT – hex, 7/16 NC x 2 inch, replaces 413-632 bolt, 3/8 NC x 2 inch, if
20 231-4117 1 NUT, LOCK, 7/16″-14, GB, hex, self-locking, 7/16 inch NC, replaces 131-463 nut, 3/8 inch NC, if used
21 219-8 1 NIPPLE, LUBE, 1/4″-28 NPT x .54″ lg
23 413-728 1 BOLT, Hex, 7/16″-14 x 1 3/4″, G5
24 232-4117 1 NUT, LOCK, 7/16″-14, GC
27 495-81074 1 WASHER, 1 1/32″ x 1 3/4″ x .120″, Flat
28 425-1914 1 NUT, SLOTTED, 7/8″-14, G5, Thk
29 32-1028 1 PIN, SPLIT (COTTER), 5/32″ x 1 3/4″
31 1259579C5 1 ARM, ASSEMBLY – center, steering, Includes: Ref. 32
32 1259581C1 2 BUSHING, center steering arm
33 219-17 1 NIPPLE, LUBE, 3/16″ x .55″ lg, Drive
34 238-5214 2 O-RING, -214, 70 Duro, .984″ ID x .139″ Thk
37 1334694C1 1 PIN, AXLE, pivot, center arm
38 38-31624 1 PIN, ROLL, 1/4″ x 1 1/2″, Coiled
40 1259582C3 2 FITTING, cap, trunnion
41 396-31081 2 WASHER, 13/16″ x 1 1/2″ x .219″, HDN
42 628-20060 2 BOLT, Hex, M20 x 60, 10.9, Full Thd
1 806-12030 1 BOLT, Hex, Lock, M12 x 30, Cl 10.9, BOLT – hex, locking, 12 – 1.75 x 30 mm, replaces 30225R1 bolt
2 101936C2 1 WASHER, flat, hardened, special
5 196338A1 1 PIN, LARGE, pivot, front axle
6 A177855 2 WASHER, thrust
8 137316A2 1 SUPPORT ASSY., BOLSTER – steering
10 196294A1 2 BUSHING, front pivot
12 192896A1 4 PLUG, front support, if used
1 231004A1 1 AXLE (CENTRE PART), HOUSING ASSEMBLY – front
2 37-1816 2 DOWEL, 1/2″ x 1″, PIN – 1/2 x 1 inch, hardened
4 1969527C1 2 PLATE ASSY., stop, front axle
5 828-12050 4 BOLT, Hex, M12 x 50, 10.9
6 221-887 2 PLUG, square socket, 3/4 inch PT
10 628-14040 16 BOLT, Hex, M14 x 40, 10.9, Full Thd, BOLT – hex, full threads, 14 – 2.0 x 40 mm, class 10.9
11 247661A1 16 WASHER, flat
12 248232A1 1 KNUCKLE, STEERING, ASSEMBLY – left-hand, includes item 14
12 248233A1 1 KNUCKLE, STEERING, ASSEMBLY – right-hand, shown, Includes: Ref. 13, 14
13 128647A1 1 SEAL, oil, 1-9/16 x 2-1/8 x 1/2 inch
14 235628A1 1 BUSHING, spindle
18 247305A1 2 STOP, ROD – steering, standard
18 247306A1 2 STOP, ROD – steering, optional
19 139217A1 2 SPLIT PIN/SAFETY PIN, CLIP – retainer
20 427-12267 2 PIN, CLEVIS, 3/4″ x 2.672″, clevis, 3/4 x 2-43/64 inch
22 1342940C1 1 BOOT, dust, ball joint
23 432-824 1 PIN, SPLIT (COTTER), 1/8″ x 1 1/2″
24 429-1314 1 NUT, SLOTTED, 7/8″-14, G8, hex, 7/8 inch NF, grade 8
25 128591A1 1 NUT, hex, special, left-hand thread
26 247290A1 1 TIE ROD, front axle
27 128589A1 1 NUT, hex, special, right-hand thread
29 1342940C1 1 BOOT, dust, ball joint
30 432-824 1 PIN, SPLIT (COTTER), 1/8″ x 1 1/2″
31 429-1314 1 NUT, SLOTTED, 7/8″-14, G8, hex, 7/8 inch NF, grade 8
33 628-12040 16 BOLT, Hex, M12 x 40, 10.9, Full Thd
34 896-11012 16 WASHER, M13.5 x 24.5 x 3, HT
35 219-1 4 NIPPLE, LUBE, 1/8″-27 x .66 lg
36 231014A1 4 CAP, king pin
38 1277271C1 4 RETAINER, grease
39 671033R1 4 BEARING SET, bearing
40 671032R1 4 BEARING, CONE, bearing
41 1277270C1 4 SEAL, OIL, king pin
1 250732A1 1 YOKE, SHAFT ASSEMBLY – axle, left, includes items 1-5
1 250733A1 1 YOKE, SHAFT ASSEMBLY – axle, right (Shown), Includes: Ref. 3, 4, 5 and Kit
5 A76014 1 SEAL, oil
6 247297A1 1 RETAINER, axle
10 247298A1 1 KIT, cross, bearing, Includes: Ref. 11, 12
13 231020A2 2 YOKE, YOKE – center, front axle
14 231021A2 2 YOKE, YOKE ASSEMBLY – outer, front axle, Includes: Ref. 15, 16, 17
15 1961753C1 1 SEAL, yoke, inner
16 1277405C1 1 RING, retaining
17 1287608C1 1 SEAL, yoke, outer
21 828-10040 6 BOLT, Hex, M10 x 40, 10.9, Full Thd
22 396-21041 6 WASHER, 13/32″ x 13/16″ x .09″, HDN, flat, 13/32 x 13/16 x 3/32 inch, hardened
3 896-12016 4 WASHER, M17.5 x 30 x 4, HT, flat, 17.5 x 30 x 4 mm, hardened
4 828-16090 4 BOLT, Hex, M16 x 90, 10.9
21 1997853C1 8 BOLT, BOLT – special, differential case
25 H136416 12 SCREW, BOLT – hex head
26 H224501 1 WASHER, flat, special, 7/8 inch
27 232-46114 1 NUT, LOCK, 7/8″-14, GC
28 251189A1 1 SPACER, pinion gear
32 1968297C1 1 BEARING, CUP, tapered roller
33 1968296C1 1 BEARING, CONE, tapered roller
34 1968289C1 1 BEARING, CUP, tapered roller
35 1968288C1 1 BEARING, CONE, tapered roller
38 912712R1 1 WASHER, pinion oil seal
42 H758326 1 SEAL ASSY., oil, pinion shaft
43 345427C1 1 SLINGER, RING – dust shield
44 1961747C1 1 YOKE, pinion shaft
45 1968291C1 2 BEARING, CONE – tapered roller, differential mounting
46 1968292C1 2 BEARING, CUP – tapered roller, 4-1/8 inch OD, differential mounting
47 1277233C1 2 RING, differential bearing adjust
48 1277234C1 2 CLEVIS, bearing adjusting ring
49 496-11034 2 WASHER, 11/32″ x 11/16″ x 1/16″, HDN
50 628-8016 2 BOLT, Hex, M8 x 16, 10.9, Full Thd
1 328500A1 2 SEAL, OIL, oil, wheel hub, rerplaces 128648A1 seal
2 1277343C1 2 BEARING, CONE, tapered roller, inner
3 1277344C1 2 BEARING, CUP, tapered roller, inner
4 231022A1 2 HUB, front wheel
5 231023A1 20 STUD, BOLT – wheel
7 L33732 2 CUP ASSY., tapered roller bearing, outer
8 L33737 2 BEARING, CONE, tapered roller, outer
10 1349339C1 2 SEAL, V-ring
12 1277250C1 2 GEAR, RING, planetary
14 251190A1 2 PLATE, LARGE, retaining, planetary carrier
15 628-12040 12 BOLT, Hex, M12 x 40, 10.9, Full Thd
16 250728A1 2 SUN GEAR, planetary drive
19 102-12175 4 RING, SNAP, #175, 1.673″, Ext Spiral, external spiral retaining, No. 175
20 1277372C2 8 SPACER, flat, 1/16 inch thick, used in gear assembly 249416A1
21 78831C1 476 NEEDLE, BEARING –
22 1277371C1 4 SPACER, bearing
23 1349038C1 4 PINION, GEAR – planetary
24 231024A1 1 FLANGE, CARRIER – planetary gears, used in gear assembly 249416A1, no longer available, order
26 221-887 1 PLUG, square socket, 3/4 inch PT
27 863-6020 4 SCREW, Hex Soc Hd, M6 x 20, 12.9, BOLT – hex socket, 6 – 1 x 20 mm
28 230856A1 20 NUT, hex flange, wheel
2 1282023C1 1 NUT, hex lock, cylinder rod
3 247285A1 1 PISTON, cylinder, no longer available, order correct assembly
15 231009A1 1 ROD, PISTON, cylinder, right-hand (Shown)
15 231010A1 1 ROD, PISTON, cylinder, left-hand
18 247289A1 1 CAP CYLINDER END, GLAND – no longer available, order correct assembly
19 219-36 1 NIPPLE, LUBE, 45є, 1/8″ NPT x 7/8″ lg
20 429-1314 1 NUT, SLOTTED, 7/8″-14, G8, hex, 7/8 inch NF, grade 8
21 432-824 1 PIN, SPLIT (COTTER), 1/8″ x 1 1/2″
25 1277261C1 2 BALL JOINT, ASSEMBLY – cylinder, Includes: Ref. 26, 27, 28
26 219-36 1 NIPPLE, LUBE, 45є, 1/8″ NPT x 7/8″ lg
27 429-1314 1 NUT, SLOTTED, 7/8″-14, G8, hex, 7/8 inch NF, grade 8
28 432-824 1 PIN, SPLIT (COTTER), 1/8″ x 1 1/2″
29 414-1044 2 BOLT, Hex, 5/8″-18 x 2 3/4″, G5, BOLT – hex, 5/8 NF x 2-3/4 inch
30 492-11062 2 WASHER, LOCK, 5/8″
31 425-1110 2 NUT, 5/8″-18, G5
1 1270629C1 2 RIM, front, W11L x 16.1, for 14L x 16.1 tire
1 1270628C1 2 RIM, front, W14L x 16.1, for 16.5L x 16.1 tire
2 1342033C1 16 BOLT, BOLT – hex flange special
3 A38261 2 VALVE, stem, tire inflation
8 1259528C1 2 HUB, ASSEMBLY – wheel, front, see Figure 5-22
1 231029A1 1 RIM, replaces 240678A1 rim
3 240685A1 1 FLANGE, DISC – wheel
4 240686A1 8 BOLT, SPECIAL, BOLT – special
5 896-11016 8 WASHER, M17.5 x 30 x 4, HT, Replaces 240675A1 washer
6 829-1416 8 NUT, M16, Cl 10, Replaces 240674A1
1 188326A1 1 RIM, replaces 255408A1 rim
3 240677A1 1 FLANGE, DISC – wheel
4 240686A1 8 BOLT, SPECIAL, BOLT – special
5 896-11016 8 WASHER, M17.5 x 30 x 4, HT, Replaces 240675A1 washer
6 829-1416 8 NUT, M16, Cl 10, Replaces 240674A1
1 188333A1 1 RIM, replaces 240680A1 rim
3 240677A1 1 FLANGE, DISC – wheel
4 240686A1 8 BOLT, SPECIAL, BOLT – special
5 896-11016 8 WASHER, M17.5 x 30 x 4, HT, Replaces 240675A1 washer
6 829-1416 8 NUT, M16, Cl 10, Replaces 240674A1
1 188350A1 1 RIM, replaces 240681A1 rim
3 240677A1 1 FLANGE, DISC – wheel
4 240686A1 8 BOLT, SPECIAL, BOLT – special
5 896-11016 8 WASHER, M17.5 x 30 x 4, HT, Replaces 240675A1 washer
6 829-1416 8 NUT, M16, Cl 10, Replaces 240674A1
1 188338A1 1 RIM, not shown, replaces 225412A1 rim
3 240677A1 1 FLANGE, DISC – wheel
4 240686A1 8 BOLT, SPECIAL, BOLT – special
5 896-11016 8 WASHER, M17.5 x 30 x 4, HT, Replaces 240675A1 washer
6 829-1416 8 NUT, M16, Cl 10, Replaces 240674A1
1 188341A1 1 RIM, replaces 240683A1 rim
3 240677A1 1 FLANGE, DISC – wheel
4 240686A1 8 BOLT, SPECIAL, BOLT – special
5 896-11016 8 WASHER, M17.5 x 30 x 4, HT, Replaces 240675A1 washer
6 829-1416 8 NUT, M16, Cl 10, Replaces 240674A1
1 258255A1 1 RIM
3 259373A1 1 FLANGE, DISC – wheel
4 240686A1 8 BOLT, SPECIAL, BOLT – special
5 896-11016 8 WASHER, M17.5 x 30 x 4, HT
6 829-1416 8 NUT, M16, Cl 10
1 93356C6 1 HOUSING, ASSEMBLY – clutch, Includes: Ref. 2, 2, 3, 4
2 217-442 1 PLUG, Hex Soc, 3/4″-14, hex socket headless, 3/4 inch PT (Without MFD)
2 192792A1 2 PLUG, square countersunk, 3/4 – 14 inch thread (With MFD)
3 837-12030 2 DOWEL, M12 x 30
4 30357R1 1 PLUG, M50, Tapered, tapered cup, 50 mm (Without MFD)
6 1981205C1 1 COVER, lube
10 628-10025 4 BOLT, Hex, M10 x 25, 10.9, Full Thd
16 131165A1 1 FITTING, lube, INCLUDES REFS 17, 18
17 237-6010 1 O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
18 238-6016 1 O-RING, -016, 90 Duro, .614″ ID x .070″ Thk
20 201-401 1 TEE, 11/16″-16 x 9/16″-18 Br, ORFS, 9/16-18 adj O-ring boss branch x 11/16-16 inch face seal x face
22 238-6012 2 O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
25 93105C1 1 UNION, ADAPTER – bulkhead, 13/16-16 face x 3/4-16 inch O-ring (With creep)
26 238-6014 1 O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
27 237-6008 1 O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
28 214389 1 PLUG, Hex Hd, 3/4″-16 ORB, Without creep, Includes Ref. 29
29 237-6008 1 O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
31 38834 1 BEARING, ROLLER, needle
32 628-20060 1 BOLT, Hex, M20 x 60, 10.9, Full Thd, If used
32 828-20090 1 BOLT, Hex, M20 x 90, 10.9, If used
33 896-12020 1 WASHER, M20 x 37.5 x 4, HT, flat, 22 x 37 x 4 mm, hardened
34 813-16060 8 BOLT, Hex, M16 x 60, 8.8, Full Thd, Bolt, Hex, M16 x 60, 8.8, Full Thd, replaces 813-16055
34 828-16080 1 BOLT, Hex, M16 x 80, 10.9
35 896-11016 9 WASHER, M17.5 x 30 x 4, HT
46 76349 3 PLUG, Hex Hd, 9/16″-18 ORB, Incl. Ref 47
48 218-5158 1 PLUG, Hex Hd, 1 1/16″-12 ORB, hex, 1-1/16-12 inch O-ring boss, Includes: Ref. 49
49 237-6012 1 O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk
61 1994583C2 1 GASKET, body plate to mounting plate
62 144143C2 1 GASKET, mounting plate to clutch housing
63 1994609C2 1 PLATE, LARGE, ASSEMBLY – mounting, transmission control valve, parts list Figure 6-26
64 814-10055 4 BOLT, Hex, M10 x 55, 8.8
65 863-10040 2 SCREW, Hex Soc Hd, M10 x 40, 12.9, BOLT – hex socket, 10 – 1.5 x 40 mm, class 12.9
66 1286093C3 1 RETAINER, tube
67 1963936C1 2 TUBE, first, second, third and fourth speed
68 1963937C1 1 TUBE, fifth and sixth speed
69 1963938C1 1 TUBE, reverse
70 238-6016 8 O-RING, -016, 90 Duro, .614″ ID x .070″ Thk
73 1286090C1 1 TUBE, clutch, front low
74 1286091C1 1 TUBE, clutch, front medium
75 1286092C1 1 TUBE, clutch, front high
76 238-6212 3 O-RING, -212, 90 Duro, .859″ ID x .139″ Thk
77 863-10040 1 SCREW, Hex Soc Hd, M10 x 40, 12.9, BOLT – hex socket, 10 – 1.5 x 40 mm, class 12.9
21 237-6006 1 O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
47 237-6006 1 O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
1 225199A1 1 SHAFT ASSY., input, Includes: Ref. 3, 4, 5
3 1342851C1 2 PLUG, sealing, 10 mm
4 1963888C1 2 PIN, slotted spring
5 38-3605 5 PIN, 3/32″ x 5/16″, Coiled
8 220617A1 1 CARRIER, CARRIER –
9 93350C1 6 RING, retaining
10 1286081C1 2 O-RING, RING – piston, low clutch inner
11 1286076C1 2 RING, piston, clutch
12 1285998C1 2 PISTON, clutch
13 1286083C1 2 O-RING, piston, low clutch outer
14 1286079C1 2 RING, piston, shift
18 93129C1 6 WASHER, Belleville spring
19 93190C1 2 DISC, reaction
20 92935C5 14 DISC, friction
21 92934C2 12 DISC, separator
22 1342854C2 2 DISC, backing, 16.5 mm (21/32 inch) thick, if used
22 1342645C3 2 DISC, CLUTCH, backing, 9.7 mm (3/8 inch) thick, power metal, if used
23 1285996C1 2 RING, SNAP, retaining
24 1286012C2 26 WASHER, Belleville spring
25 1286043C1 6 WASHER, THRUST
28 572182R1 3 BEARING, THRUST, needle
29 80907C1 2 BEARING, NEEDLE, caged
30 93297C1 1 SPACER, bearing
31 1342495C1 1 GEAR, DRIVEN, GEAR – second, fourth and sixth, 37 teeth
32 1286052C1 2 RING, seal
33 1286042C1 2 WASHER, THRUST
36 K620185 1 BEARING, THRUST, needle, thrust
38 1285985C1 1 GEAR, WHEEL, odd/even clutch and fifth, 34 Teeth
39 1286016C1 1 BEARING, NEEDLE, caged
40 1286039C1 2 SPACER, bearing
41 364465C1 1 BEARING, CONE, tapered roller
42 258452C1 1 BEARING, CUP, tapered roller
43 1286026C1 5 RING, seal
44 1981213C1 1 CAGE, bearing
48 613-10030 4 BOLT, Hex, M10 x 30, 8.8, Full Thd, BOLT – hex, full threads, 10 – 1.5 x 30 mm
50 1981207C1 1 TUBE, lube
52 627639R1 1 BEARING, CONE, tapered roller
53 ST970 1 BEARING, CUP, tapered roller
54 1997371C1 1 SEAL, shaft
55 1286118C3 1 SUPPORT ASSY., bearing, front, INCLUDES REF 56
56 37-188 8 DOWEL, 1/2″ x 1/2″, dowel, hardened, 1/2 x 1/2 inch
57 613-12040 11 BOLT, Hex, M12 x 40, 8.8, Full Thd, BOLT – hex, 12 – 1.75 x 40 mm, replaces 615-12040 bolt
60 226637A1 1 COUPLING, SPLINED, shaft input
61 1342448C1 1 SHAFT, driven
1 228398A1 1 SHAFT ASSY., input, Includes: Ref. 3, 4, 5
3 1342851C1 4 PLUG, sealing, 10 mm
4 1963888C1 2 PIN, slotted spring
5 38-3605 5 PIN, 3/32″ x 5/16″, Coiled
8 220617A1 1 CARRIER, CARRIER –
9 93350C1 6 RING, retaining
10 1286081C1 2 O-RING, piston, low clutch inner
11 1286076C1 2 RING, piston, clutch
12 1285998C1 2 PISTON, clutch
13 1286083C1 2 O-RING, piston, low clutch outer
14 1286079C1 2 RING, piston, shift
18 93129C1 6 WASHER, Belleville spring
19 93190C1 2 DISC, reaction
20 92935C5 14 DISC, friction
21 92934C2 12 DISC, separator
22 1342854C2 2 DISC, backing, 16.5 mm (21/32 inch) thick, if used
22 1342645C3 2 DISC, CLUTCH, backing, powder metal, 9.7 mm (3/8 inch) thick, if used
23 1285996C1 2 RING, SNAP, retaining
24 1286012C2 26 WASHER, Belleville spring
25 1286043C1 6 WASHER, THRUST
28 572182R1 3 BEARING, THRUST, needle
29 80907C1 2 BEARING, NEEDLE, caged
30 93297C1 1 SPACER, bearing
31 1342495C1 1 GEAR, DRIVEN, GEAR – second, fourth and sixth, 37 teeth
32 1286052C1 2 RING, seal
33 1286042C1 2 WASHER, THRUST
36 K620185 1 BEARING, THRUST, needle, thrust
37 92793C1 1 RING, retaining
38 1285985C1 1 GEAR, WHEEL, odd/even clutch and fifth, 34 teeth
39 1286016C1 1 BEARING, NEEDLE, caged
40 1286039C1 2 SPACER, bearing
41 364465C1 1 BEARING, CONE, tapered roller
42 258452C1 1 BEARING, CUP, tapered roller
43 1286026C1 5 RING, seal
44 1981213C1 1 CAGE, bearing
48 613-10030 4 BOLT, Hex, M10 x 30, 8.8, Full Thd, BOLT – hex, full threads, 10 – 1.5 x 30 mm
50 1981207C1 1 TUBE, lube
52 L33289 1 BEARING, CONE, tapered roller, 2-1/4 inch ID
53 105497H 1 BEARING, CUP, tapered roller
54 108935A1 1 SEAL, shaft, Part of Service Kit P/N 108934A1
55 92837C3 1 SUPPORT ASSY., bearing, Includes: Ref.
56 37-188 8 DOWEL, 1/2″ x 1/2″, dowel, hardened, 1/2 x 1/2 inch, replaces 20229R1 pin
57 613-12040 11 BOLT, Hex, M12 x 40, 8.8, Full Thd, BOLT – hex, 12 – 1.75 x 40 mm, replaces 615-12040 bolt
58 92794C1 1 PINION, GEAR – creeper, 17 teeth
60 228465A1 1 COUPLING, SPLINED, shaft input
61 218-5103 1 ELBOW, 90є, 7/16″-20, 37є x 7/16″-20, O-Ring, 90 degree, 7/16-20 inch flare x adj O-ring boss
62 237-6004 1 O-RING, 4-1, 90 Duro, .351″ ID x .072″ Thk
63 311670A1 1 TUBE, supply, lube, replaces 92836C1 tube
64 108932A1 1 O-RING, O-RING – 40.87 ID x 3.53 mm wide, Part of Service Kit P/N 108934A1
65 108933A1 1 SHAFT, driven, damper, with 4.45 mm wide O-ring groove, Part of Service Kit P/N 108934A1
1 1342253C2 1 SHAFT, counter
2 100-11293 2 RING, SNAP, #293, Ext
4 1285983C1 1 GEAR, DRIVING, GEAR – driver, third and fourth, 34 teeth
5 211-1012 4 BALL, 3/8″ Dia, chrome alloy steel, 3/8 inch, grade 24
7 ST791 1 BEARING, CONE, tapered roller
8 ST951 1 BEARING, CUP, tapered roller
11 1285981C1 1 PINION, GEAR – driver, first and second, 29 teeth
12 ST2051 1 BEARING, CONE, tapered roller
13 ST863 1 BEARING, CUP, tapered roller
14 1286000C3 1 CAGE, bearing
18 613-10025 6 BOLT, Hex, M10 x 25, 8.8, Full Thd, BOLT – hex, full threads, 10 – 1.5 x 25 mm
20 1285989C1 1 PINION, GEAR – driven, second, fourth and sixth speed, 37 teeth
22 1285986C1 1 PINION, GEAR – driven, first, third and fifth speed, 39 teeth
1 1342318C2 1 SHAFT, COUNTERSHAFT ASSEMBLY – transmission, Includes: Ref. 2, 3, 4
2 1286084C1 2 PIN, dowel, 12 x 11 mm
3 92825C1 1 PLUG, countershaft
4 1963875C1 1 PIN, SPLIT (COTTER), slotted spring
5 211-1012 4 BALL, 3/8″ Dia, chrome alloy steel, 3/8 inch, grade 24
7 100-11293 1 RING, SNAP, #293, Ext
9 1285983C1 1 GEAR, DRIVING, GEAR – driver, third and fourth, 34 teeth
10 144242C3 2 RING, seal, 33 mm
11 92828C1 1 CAGE, bearing
12 613-10025 6 BOLT, Hex, M10 x 25, 8.8, Full Thd, BOLT – hex, full threads, 10 – 1.5 x 25 mm
15 218-5057 1 CONNECTOR, HYD., 9/16″-18, 37є x 9/16″-18, O-Ring, Incl. Ref. 16
17 93104C2 1 UNION, bulkhead
19 92848C1 1 TUBE, pressure
20 92824C1 1 SPACER, carrier
21 92797C1 1 HOUSING, CLUTCH, CARRIER –
22 1286081C1 1 O-RING, piston, low clutch inner
23 238-6012 1 O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
25 1286076C1 1 RING, piston, clutch
26 1285998C1 1 PISTON, clutch
27 1286083C1 1 O-RING, piston, low clutch outer
28 1286079C1 1 RING, piston, shift
33 93129C1 3 WASHER, Belleville spring
34 93190C1 1 DISC, reaction
35 92935C5 8 DISC, friction
36 92934C2 7 DISC, separator
37 1342645C3 1 DISC, CLUTCH, backing, 9.7 mm (3/8 inch) thick
38 1285996C1 1 RING, SNAP, retaining
39 93350C1 2 RING, retaining
40 1286012C2 13 WASHER, Belleville spring
41 1286043C1 2 WASHER, THRUST
42 572182R1 1 BEARING, THRUST, needle
43 1286052C1 1 RING, RING –
51 92795C1 1 PINION, GEAR – driven
52 80906C1 1 BEARING, NEEDLE, needle, caged (1-1/4 inch)
53 1286042C1 2 WASHER, THRUST
54 K620185 1 BEARING, THRUST, needle, thrust
55 ST2051 2 BEARING, CONE, tapered roller
56 ST863 2 BEARING, CUP, tapered roller
58 1285986C1 1 PINION, GEAR – driven, first, third and fifth speed, 39 teeth
61 1285989C1 1 PINION, GEAR – driven, second, fourth and sixth speed, 37 teeth
62 1285981C1 1 PINION, GEAR – driver, first and second, 29 teeth
16 237-6006 1 O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
18 237-6006 2 O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
1 230135A1 1 SHAFT, ASSEMBLY – output, no longer available, order 230135A2 shaft below
1 230135A2 1 SHAFT, ASSEMBLY – output, Includes: Ref. 2-5
2 1342852C1 3 PLUG, sealing, 12 mm, used with 230135A1 shaft assembly
2 187516A1 3 PLUG, expansion, used with 230135A2 shaft assembly
4 38-3605 6 PIN, 3/32″ x 5/16″, Coiled
5 1963875C1 4 PIN, SPLIT (COTTER), slotted spring
8 1286040C2 1 RING, support
9 1997888C1 1 WASHER, THRUST
10 1286016C1 1 BEARING, NEEDLE, caged
11 1285985C1 1 GEAR, WHEEL, odd/even clutch and fifth, 34 teeth
12 1285987C1 1 PINION, GEAR – driven, reverse, 39 teeth
13 1286052C1 2 RING, seal
16 1286043C1 4 WASHER, THRUST
17 572182R1 2 BEARING, THRUST, needle
18 93350C1 4 RING, retaining
19 1286012C2 24 WASHER, Belleville spring
20 93304C2 1 HOUSING, CLUTCH, CARRIER –
22 1286081C1 2 O-RING, piston, low clutch inner
23 1286076C1 2 RING, piston, clutch
24 1285998C1 2 PISTON, clutch
25 1286083C1 2 O-RING, piston, low clutch outer
26 1286079C1 2 RING, piston, shift
29 93129C1 3 WASHER, Belleville spring
30 93190C1 2 DISC, reaction
31 92935C5 14 DISC, friction
32 92934C2 12 DISC, separator
33 1342854C2 2 DISC, backing, 16.5 mm (21/32 inch) thick, if used
33 1342645C3 2 DISC, CLUTCH, backing, powder coated, 9.7 mm (3/8 inch) thick, if used
34 1285996C1 2 RING, SNAP, retaining
35 93129C1 3 WASHER, Belleville spring
36 80907C1 1 BEARING, NEEDLE, caged
37 1342513C1 1 SPACER, bearing
39 1286042C1 2 WASHER, THRUST
40 K620185 1 BEARING, THRUST, needle, thrust
44 219530H1 1 BEARING, CONE, tapered roller
45 ST964 1 BEARING, CUP, tapered roller
46 1286024C1 4 RING, seal
47 238-5223 1 O-RING, -223, 70 Duro, 1.609″ ID x .139″ Thk, 1-3/4 ID x 1/8 inch wide
1 230135A2 1 SHAFT, ASSEMBLY – output, see Figure 6-14 for pins and plugs
2 238-5223 1 O-RING, -223, 70 Duro, 1.609″ ID x .139″ Thk, 1-3/4 ID x 1/8 inch wide
10 1286016C1 1 BEARING, NEEDLE, caged
13 1286052C1 2 RING, seal
16 1286043C1 4 WASHER, THRUST
17 572182R1 2 BEARING, THRUST, needle
18 93350C1 4 RING, retaining
19 1286012C2 26 WASHER, Belleville spring
21 1285970C2 1 HOUSING, CLUTCH, CARRIER – first and third
22 1286081C1 2 O-RING, piston, low clutch inner
23 1286076C1 2 RING, piston, clutch
24 1285998C1 2 PISTON, clutch
25 1286083C1 2 O-RING, piston, low clutch outer
26 1286079C1 2 RING, piston, shift
29 93129C1 6 WASHER, Belleville spring
30 93190C1 2 DISC, reaction
31 92935C5 18 DISC, friction
32 92934C2 16 DISC, separator
33 1342854C2 2 DISC, backing, 16.5 mm (21/32 inch) thick, if used
33 1342645C3 2 DISC, CLUTCH, backing, powder coated, 9.7 mm (3/8 inch) thick, if used
34 1285996C1 2 RING, SNAP, retaining
35 1285984C1 1 GEAR, GEAR – driven, third and fourth, 39 teeth
37 1285982C1 1 GEAR, DRIVEN, GEAR – driven, first and second, 44 teeth
38 1285997C1 1 BEARING, NEEDLE, caged
39 1286042C1 2 WASHER, THRUST
40 K620185 1 BEARING, THRUST, needle, thrust
47 1286021C1 1 BEARING, ROLLER, CONE – tapered
48 29214H 1 BEARING, CUP, tapered roller, 4-5/16 inch OD
49 1286001C3 1 CAGE, bearing
51 613-10025 4 BOLT, Hex, M10 x 25, 8.8, Full Thd, BOLT – hex, full threads, 10 – 1.5 x 25 mm
1 125806A1 1 HOUSING, ASSEMBLY – range, transmission, no longer offered, order 304473A2 housing below
1 304473A2 1 HOUSING, ASSEMBLY – range, transmission, Includes: Ref. 2-7
2 837-16035 4 DOWEL, M16 x 35, PIN – 16 x 35 mm, hardened
3 837-12025 2 DOWEL, M12 x 25, Hardened
5 192792A1 1 PLUG, square countersunk, 3/4 – 14 inch thread
6 221-847 1 PLUG, Hex Soc, 1 1/4″-11 1/2, square socket headless, 1-1/4 inch PT (Without heater), used with
6 327080A1 1 PLUG, 1-1/4 inch PT, used with 304473A2 housing
7 41-1618 1 PLUG, Cup, 1 1/8″, Stainless, cup, 1-1/8 inch diameter (Without hitch)
10 214389 1 PLUG, Hex Hd, 3/4″-16 ORB, Without MFD
11 237-6008 1 O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
12 87390949 1 GASKET, housing
13 896-11016 12 WASHER, M17.5 x 30 x 4, HT
14 813-16060 10 BOLT, Hex, M16 x 60, 8.8, Full Thd, Bolt, Hex, M16 x 60, 8.8, Full Thd
14 828-16080 2 BOLT, Hex, M16 x 80, 10.9, Replaces 814-16070
15 92821C2 1 GASKET, housing
16 93364C1 1 COVER, access
17 628-10025 12 BOLT, Hex, M10 x 25, 10.9, Full Thd, Replaces 615-10025
20 1976744C2 1 COVER ASSY, opening
21 613-10020 4 BOLT, Hex, M10 x 20, 8.8, Full Thd, BOLT – hex, full threads, 10 – 1.5 x 20 mm
24 301533R1 1 BEARING, NEEDLE, front, pinion shaft
28 1340584C1 1 TUBE, dipstick
29 825-1406 1 NUT, M6, Cl 8
30 614-6020 1 BOLT, Hex, M6 x 20, 8.8, Full threads
31 1342132C1 1 SUPPORT, BRACKET – dipstick (With hitch)
31 1342155C1 1 SUPPORT, BRACKET – dipstick (Without hitch)
32 515-21127 1 CLAMP, 1/2″, Insul, 1/4″ Bolt, P-type
33 1342137C2 1 DIPSTICK, oil level
34 1968044C2 1 TUBE, dipstick, internal
35 238-6014 1 O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
36 605-16020 2 BOLT, Hex, Lock, M16 x 20, Cl 8.8, BOLT – hex, locking, 16 – 2.0 x 20 mm
40 536850R1 1 HEATER, HEATER ASSEMBLY – oil, transmission, components not serviced seperately
1 124542A1 1 MANIFOLD, lubrication
2 145400C2 1 GASKET, manifold
3 814-10070 3 BOLT, Hex, M10 x 70, 8.8, BOLT – hex, 10 – 1.5 x 70 mm
3 864-10070 1 SCREW, Hex Soc Hd, M10 x 70, 8.8
6 201-101 2 CONNECTOR, HYD., 11/16″-16 ORFS x 9/16″-18 ORB, ADAPTER – straight, 11/16-16 face seal x
7 237-6006 1 O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
8 238-6012 1 O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
10 201-306 1 ELBOW, 90є, 1″-14 x 7/8″-14 Adj, ORFS, 90 degree, 1-14 face seal x 7/8-14 inch adj O-ring boss
13 201-420 1 TEE, 1″-14 x 7/8″-14 Run, ORFS, 1-14 face branch x face x 7/8-14 inch adj O-ring boss (With creeper)
14 237-6010 1 O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
15 238-6016 1 O-RING, -016, 90 Duro, .614″ ID x .070″ Thk
16 201-310 1 ELBOW, 90є, 2″-12 x 1 7/8″-12, Adj, ORFS, 90 degree, 2-12 face x 1-7/8 inch adj O-ring boss
17 237-6024 1 O-RING, 24-1, 90 Duro, 1.72″ ID x .118″ Thk
18 238-6029 1 O-RING, -029, 90 Duro, 1.489″ ID x .070″ Thk
22 1342029C1 1 TUBE, lubrication, odd/even
23 1348316C1 1 PIPE, TUBE – lubrication, creeper drive
24 131165A1 1 FITTING, lube, INCLUDES REFS 25, 26
25 237-6010 1 O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
26 238-6016 2 O-RING, -016, 90 Duro, .614″ ID x .070″ Thk
27 1349444C1 1 TUBE, lubrication, draft cylinder
28 201-120 1 CONNECTOR, HYD., 11/16″-16, Blkhd, ORFS, straight, 11/16-16 inch face seal x bulkhead face seal
29 238-6012 1 O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
33 86625138 2 PLUG, Hex Soc, 7/8″-14 ORB, Includes Ref. 34
34 237-6010 1 O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
37 201-101 1 CONNECTOR, HYD., 11/16″-16 ORFS x 9/16″-18 ORB, ADAPTER – straight, 11/16-16 face seal x
38 237-6006 1 O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
39 238-6012 1 O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
40 201-103 1 CONNECTOR, HYD., 1″-14 ORFS x 7/8″-14 ORB, Includes Ref. 41, 42
41 237-6010 1 O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
42 238-6016 1 O-RING, -016, 90 Duro, .614″ ID x .070″ Thk
43 9672438 1 PLUG, Hex Hd, 7/16″-20 ORB, Assy, Oil, Transmission, Components not serviced seperately, Incl.
44 237-6004 1 O-RING, 4-1, 90 Duro, .351″ ID x .072″ Thk
50 1289215C1 1 TUBE, lube main supply
51 201-102 1 CONNECTOR, HYD., 13/16″-16 ORFS x 3/4″-16 ORB, Includes Ref. 52, 53
52 237-6008 1 O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
53 238-6014 1 O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
54 201-409 1 TEE, 13/16″-16 ORFS, 13/16-16 inch face seal branch x face seal x face seal, Includes: Ref. 55
55 238-6014 3 O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
56 1289214C1 1 TUBE, lube, right-hand brake
57 1289212C1 1 TUBE, lube, left-hand brake
58 107813A1 1 PIPE, TUBE – lubrication, PTO rear
60 201-402 1 TEE, 13/16″-18 x 3/4″-16 Br, ORFS, 3/4-16 adj O-ring branch x 13/16-16 inch face x face, Includes:
61 237-6008 1 O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
62 238-6014 2 O-RING, -014, 90 Duro, .489″ ID x .070″ Thk
70 76349 1 PLUG, Hex Hd, 9/16″-18 ORB, (Without MFD), Incl. Ref 71
71 237-6006 1 O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
73 1349199C3 1 FITTING, bevel gear and bearing lube (Without hitch), Includes: Ref. 74, 75
74 237-6006 1 O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
75 238-6012 1 O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
76 1342229C3 1 COVER, housing (Without hitch)
77 1971726C1 1 BREATHER, housing
78 93103C1 1 UNION, bulkhead
79 237-6008 1 O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
80 238-6012 1 O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
81 124306A1 1 PIPE, TUBE – lube
82 1289222C1 1 PIPE, TUBE – lube, range spray
83 201-304 1 ELBOW, 90є, 11/16″-16 x 9/16″-18 Adj, ORFS, 90 degree, 11/16-16 face seal x 9/16-18 inch adj
84 237-6006 1 O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
85 238-6012 1 O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
86 9625178 1 PLUG, Hex Soc, 9/16″-18 ORB, (Without hitch), Incl. Ref. 87
87 237-6006 1 O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
88 221-62 2 REDUCER, Hex, 1″ x 1/4″ NPT, reducing pipe, 1 x 1/4 (Without hitch)
89 1330639C1 1 FITTING, ADAPTER – straight, 9/16-18 inch O-ring boss (Without hitch), Includes: Ref. 90
90 237-6006 1 O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
91 628-16035 14 BOLT, Hex, M16 x 35, 10.9, Full Thd, Bolt, Hex, M16 x 35, 10.9, Full Thd, without hitch
92 614-16100 2 BOLT, Hex, M16 x 100, 8.8, Full Thd, BOLT – hex, full threads, 16 – 2.0 x 100 mm (Without hitch)
93 657114R1 2 SPACER, 3/4″ X-Strng Pipe x 2 3/8″, 3/4 x 2-3/8 inch (Without hitch) not shown
94 896-16016 4 WASHER, M16 x 34.5 x 5, HT, flat, 17.5 x 34 x 5 mm, hardened (Without hitch) not shown
1 103182A1 1 VALVE, CONTROL, ASSEMBLY – transmission control (Without Creeper), parts list Figures 6-28 – 6-38
1 103183A1 1 VALVE, CONTROL, ASSEMBLY – transmission control (With Creeper), parts list Figures 6-28 – 6-38
3 814-10045 3 BOLT, Hex, M10 x 45, 8.8, (See Page 6-39)
4 828-8120 3 BOLT, Hex, M8 x 120, 10.9, BOLT – hex, 8 – 1.25 x 120 mm, class 10.9, see Figure 6-38
4 828-8140 8 BOLT, Hex, M8 x 140, 10.9, BOLT – hex, 8 – 1.25 x 140 mm, class 10.9, see Figure 6-38
6 814-10175 2 SCREW, BOLT – hex, 10 – 1.5 x 175 mm, see Figure 6-38
12 201-306 1 ELBOW, 90є, 1″-14 x 7/8″-14 Adj, ORFS, 90 degree, 1-14 face seal x 7/8-14 inch adj O-ring boss
13 237-6010 1 O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
14 238-6016 1 O-RING, -016, 90 Duro, .614″ ID x .070″ Thk
15 201-103 1 CONNECTOR, HYD., 1″-14 ORFS x 7/8″-14 ORB, Includes Ref. 16, 17
16 237-6010 1 O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
17 238-6016 1 O-RING, -016, 90 Duro, .614″ ID x .070″ Thk
20 201-101 1 CONNECTOR, HYD., 11/16″-16 ORFS x 9/16″-18 ORB, ADAPTER – straight, 11/16-16 face seal x
21 237-6006 1 O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
22 238-6012 1 O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
23 1968016C2 1 TUBE, inlet
24 1968170C2 1 TUBE, jumper (With creeper)
25 1342600C2 1 ANCHOR, RETAINER – tube
26 1348287C1 1 TUBE, clutch, master
27 863-10040 1 SCREW, Hex Soc Hd, M10 x 40, 12.9, BOLT – hex socket, 10 – 1.5 x 40 mm, class 12.9
28 238-7018 4 O-RING, -018, Cl 7, .739″ ID x .070″ Thk
30 1349400C1 1 TUBE, clutch, odd
31 1349402C1 1 TUBE, clutch, even
32 H434164 1 COUPLING, quick check
33 218-5450 1 ELBOW, 90є, 7/16″-20 ORB x 1/8″ NPT Fem, 90 degree, 7/16-20 O-ring boss x 1/8 inch female PT
34 237-6004 1 O-RING, 4-1, 90 Duro, .351″ ID x .072″ Thk
35 1348316C1 1 PIPE, TUBE – lubrication, creeper drive
36 1981208C1 1 SUPPORT, BRACKET – tube
37 864-10025 2 SCREW, Hex Soc Hd, M10 x 25, 8.8, BOLT – hex socket, 10 – 1.5 x 25 mm
1 1994583C2 1 GASKET, body plate to mounting plate
2 144143C2 1 GASKET, mounting plate to clutch housing
4 133519C1 1 SCREEN, filter
5 1981235C2 1 PLUG, valve
6 1975424C1 1 SPRING, check valve
7 1975438C1 1 VALVE, check
8 86529630 2 PLUG, Hex Soc, 3/8″-24 ORB
10 47-212 1 RIVET, FH, 1/8″ x 3/4″, flat head steel, 1/8 x 3/4 inch
11 511-1060 1 BALL, 6mm Dia, 6 mm, grade 28, chrome alloy steel
12 76349 3 PLUG, Hex Hd, 9/16″-18 ORB, (Without creeper), Incl. Ref 13
14 814-10055 4 BOLT, Hex, M10 x 55, 8.8
15 863-10040 1 SCREW, Hex Soc Hd, M10 x 40, 12.9, BOLT – hex socket, 10 – 1.5 x 40 mm, class 12.9
9 237-6006 1 O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
13 237-6006 1 O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
1 1994675C2 1 HOUSING, ASSEMBLY – cam, Includes: Ref. 2, 3, 4
2 G105118 1 SEAL, oil
3 37-1220 2 DOWEL, 1/8″ x 1 1/4″, dowel, 1/8 x 1-1/4 inch, hardened
4 D65128 1 BEARING, NEEDLE
8 511-1020 3 BALL, 2mm Dia, 2 mm, grade 28, chrome alloy steel
9 511-1025 4 BALL, 2.5mm Dia, 2.5 mm, grade 28, chrome alloy steel
13 100-2137 4 RING, SNAP, 0.375″, Int, #37
14 1963882C1 1 SPRING, VALVE, shuttle
15 1963881C1 1 PLUG, hex, 1-1/16-12 inch
16 237-6012 1 O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk
17 93099C4 2 COMPRESSION SPRING, DETENT – cam
18 1286235C1 2 SPRING, VALVE, detent
19 92957C1 2 PLUG, detent
20 237-8008 2 O-RING, 8-1, Cl 8, .644″ ID x .087″ Thk
23 1283927C2 1 LEVER, speed
24 837-8020 1 DOWEL, M8 x 20, dowel, 8 x 20 mm, hardened
25 92498C1 1 SHAFT, control cam, includes gear
30 93097C2 1 CAM, ASSEMBLY – gear selector, Includes: Ref. 31, 32
31 A35822 1 BEARING, cam
32 1286263C2 1 SPACER, bearing
33 92945C1 1 SHAFT, cam
38 92972C3 1 SPRING, compression
39 211-1012 1 BALL, 3/8″ Dia, chrome alloy steel, 3/8 inch, grade 24
40 129998 2 PLUG, Hex Hd, 1/2″-20 ORB, Incl. Ref. 41
41 237-6005 1 O-RING, 5-1, 90 Duro, .414″ ID x .072″ Thk
42 1286209C3 1 PLATE ASSY., cover
43 1286265C5 1 GASKET, plate
44 628-8025 12 BOLT, Hex, M8 x 25, 10.9, Full Thd, See Page 6-39
45 1981142C1 1 PLATE, LARGE, cover
46 92654C6 1 GASKET, plate
47 86529630 2 PLUG, Hex Soc, 3/8″-24 ORB, Includes Ref. 48
48 237-6003 1 O-RING, 3-1, .301″ ID x .064″ Thk
50 828-8120 1 BOLT, Hex, M8 x 120, 10.9, BOLT – hex, 8 – 1.25 x 120 mm, class 10.9 (Without manual shuttle shift)
50 828-8140 1 BOLT, Hex, M8 x 140, 10.9, BOLT – hex, 8 – 1.25 x 140 mm, class 10.9 (With manual shuttle shift), see
51 294856A1 1 CAM, neutral block (With manual shuttle shift)
52 895-11008 1 WASHER, M8 x 16 x 1.6, (With manual shuttle shift)
2 837-6035 2 DOWEL, M6 x 35, dowel, 6 x 35 mm, hardened
3 41-108 1 PLUG, Cup, 1/2″, cup, 1/2 inch diameter
4 92972C3 1 SPRING, relief
5 211-1012 1 BALL, 3/8″ Dia, chrome alloy steel, 3/8 inch, grade 24
6 133519C1 2 SCREEN, filter
7 511-1060 2 BALL, 6mm Dia, 6 mm, grade 28, chrome alloy steel
9 D65128 1 BEARING, NEEDLE
10 1286222C1 1 STOP, spool
11 1994615C2 1 VALVE, CHECK
12 1963809C1 1 SPACER, spring
13 37-1610 2 PIN, 3/8″ x 5/8″, PIN – 3/8 x 5/8 inch, hardened
21 1986857C1 1 GASKET, housing to body
22 1994584C2 1 GASKET, body to plate
23 117731A2 1 PLATE, LARGE, ASSEMBLY – body, aluminum, Includes: Ref. 24
24 1994615C2 1 VALVE, CHECK
30 1543349C2 1 HOUSING ASSY., control, clutch, Includes: Ref. 31
31 1963807C1 1 SEAL, stem
33 1286180C6 1 GASKET, housing
35 615-8030 3 BOLT, Hex, M8 x 30, 8.8, Full Thd, BOLT – hex, full threads, 8 – 1.25 x 30 mm
40 94806C3 1 HOUSING ASSY., spool, INCLUDES REF 41
41 1963843C1 1 SEAL, spool
43 93053C3 1 GASKET, housing
44 814-8075 1 BOLT, Hex, M8 x 75, 8.8
45 94797C1 1 PLATE, LARGE, housing
46 813-8080 2 BOLT, Hex, M8 x 80, 8.8, BOLT – hex, 8 – 1.25 x 80 mm
47 1983218C2 1 SWITCH, SWITCH – neutral start, Includes: Ref. 48
49 94799C1 1 PLUG, housing
50 238-5016 1 O-RING, -016, 70 Duro, .614″ ID x .070″ Thk
51 862-8055 3 SCREW, Hex Soc Hd, M8 x 55, 12.9, BOLT – hex socket, 8 – 1.25 x 55 mm, class 12.9, see Figure 6-38
52 861-8070 4 SCREW, Hex Soc Hd, M8 x 70, 12.9, BOLT – hex socket, 8 – 1.25 x 70 mm, class 12.9, see Figure 6-38
52 862-6070 1 SCREW, Hex Soc Hd, M6 x 70, 12.9, BOLT – hex socket, 6 – 1.0 x 70 mm, class 12.9, see Figure 6-38
48 237-6006 1 O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
1 1543207C3 1 BODY, BODY ASSEMBLY – transmission control valve, parts list Figure 6-30
2 93145C9 1 PISTON, SPOOL – forward/reverse
6 238-5021 1 O-RING, -021, 70 Duro, .926″ ID x .070″ Thk
7 1963812C4 1 INSERT, SEAT – spring
8 1963822C1 1 SPRING, VALVE, SPRING – detent
9 1963818C1 1 WASHER, WASHER – stop
11 94771C2 1 PIN, LARGE, PIN – stop
12 94775C1 1 STOP, STOP – pin
17 37-11224 1 DOWEL, 3/4″ x 1 1/2″, PIN – dowel, 3/4 x 1-1/2 inch, hardened
18 94798C4 1 PLUNGER, PLUNGER – valve
19 1981069C2 1 SPOOL, SPOOL – selector
21 94783C1 1 SPRING, VALVE, SPRING – selector, lock pin
22 94781C2 1 PIN, LARGE, PIN – lock
23 1286251C3 1 PIN, LARGE, PIN – spool
24 K620272 1 BEARING, NEEDLE, BEARING – reaction
25 1286264C1 1 SPACER, SPACER – bearing
28 92971C1 1 SPRING, VALVE, SPRING – flow, sensor
29 1286214C2 1 SPOOL, SPOOL – overlap
30 9672438 2 PLUG, Hex Hd, 7/16″-20 ORB, Incl. Ref. 31
31 237-6004 1 O-RING, 4-1, 90 Duro, .351″ ID x .072″ Thk
41 117942A1 1 ACCUMULATOR, RESERVOIR ASSEMBLY – accumulator, 15 cubic inch, 116 mm (4-9/16 inch)
42 1542910C1 1 FITTING, CONNECTOR – 7/8-14 x 1-1/16-12
43 237-6010 1 O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
44 237-6012 1 O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk
46 117941A1 1 ACCUMULATOR, RESERVOIR ASSEMBLY – accumulator, 30 cubic inch, 130 mm (5-1/8 inch)
47 116371A1 1 FITTING, CONNECTOR – 1-1/16-12
48 237-6012 2 O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk
1 1543207C3 1 BODY, ASSEMBLY – transmission control valve, parts list Figure 6-30
2 1968260C3 1 GASKET, lower plate and valve body
3 1981070C1 1 PLATE ASSY., lower (Without creeper)
7 86529630 2 PLUG, Hex Soc, 3/8″-24 ORB, Without creeper, Includes Ref. 8
8 237-6003 1 O-RING, 3-1, .301″ ID x .064″ Thk
10 814-8050 6 BOLT, Hex, M8 x 50, 8.8
13 211-1007 1 BALL, 7/32″ Dia, Gr 24, Chrome alloy steel
15 38-11622 1 PIN, LOCK, 1/4″ x 1 3/8″, Slotted, 1/4″ x 1 3/8″, Slotted
16 86529630 7 PLUG, Hex Soc, 3/8″-24 ORB, Includes Ref. 17
17 237-6003 1 O-RING, 3-1, .301″ ID x .064″ Thk
18 1958159C2 1 VALVE, SOLENOID, ASSEMBLY – drive, creeper, Includes: Ref. 19, 20, 21
19 238-5121 1 O-RING, -121, 70 Duro, 1.049″ ID x .103″ Thk
20 238-5017 1 O-RING, -017, 70 Duro, .676″ ID x .070″ Thk
21 238-5014 1 O-RING, -014, 70 Duro, .489″ ID x .070″ Thk
22 1968281C1 1 RETAINER, solenoid valve
23 940-148 2 SCREW, Cross Pan Hd, M4 x 8, machine, pan Phillips, 4 – .7 x 8 mm
26 1963881C1 1 PLUG, hex, 1-1/16-12 inch
27 237-6012 1 O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk
28 1968250C2 1 COMPRESSION SPRING
29 1981127C3 1 SPOOL, creeper valve
30 1981071C1 1 PLUG, valve body (With creeper)
32 86529630 2 PLUG, Hex Soc, 3/8″-24 ORB, Includes Ref. 33
33 237-6003 1 O-RING, 3-1, .301″ ID x .064″ Thk
35 814-8050 3 BOLT, Hex, M8 x 50, 8.8
36 813-8080 3 BOLT, Hex, M8 x 80, 8.8, BOLT – hex, 8 – 1.25 x 80 mm (Creeper only)
43 1963814C1 1 SPRING, compression (Creeper only)
44 1963815C1 1 SPRING, compression (Creeper only)
45 1981089C1 1 STOP, spool (Creeper only)
46 1981068C1 1 SPOOL, blocker (Creeper only)
47 837-6016 1 DOWEL, M6 x 16, dowel, 6 x 16 mm, hardened (Without creeper)
1 1543207C3 1 BODY, ASSEMBLY – transmission control valve, parts list Figure 6-30
2 93135C4 1 SPOOL, odd/even clutch selector
4 93139C5 1 SPOOL, high/low selector
12 1285738C1 1 SPRING, VALVE, inner control
13 1285739C2 1 PLUNGER, PIN – control, clutch
14 1285740C1 1 PIN, LARGE, spring
19 1286135C1 1 SPOOL, reducing, no longer available order 295768A1 spool and 295767A1 retaining ring below
19 295768A1 1 SPOOL, reducing, must use 295767A1 retaining ring with spool, Includes: Ref. 20
20 133519C1 1 SCREEN, filter
21 1286241C1 1 SPRING, VALVE, reducting
22 1286189C1 1 WASHER, RING – spring retaining
23 1286184C1 1 SNAP RING, retainer
24 92525C3 1 PISTON ASSY., spool
25 92530C1 1 SPRING, piston
31 92534C2 1 GUIDE, spring, modulating
32 1286242C1 1 SPRING, VALVE, inner, modulating
33 1286243C1 1 SPRING, VALVE, outer, modulating
34 92936C3 1 SPOOL, valve
35 92976C1 1 SPRING, VALVE, spool
36 1286251C3 2 PIN, LARGE, spool, cam
37 K620272 2 BEARING, NEEDLE, reaction
38 1286264C1 2 SPACER, bearing
39 94781C2 2 PIN, LARGE, lock, selector
40 94783C1 2 SPRING, VALVE, lock pin
1 613-8025 12 BOLT, Hex, M8 x 25, 8.8, Full Thd, BOLT – hex, full threads, 8 – 1.25 x 25 mm
5 828-8120 1 BOLT, Hex, M8 x 120, 10.9, BOLT – hex, 8 – 1.25 x 120 mm, class 10.9 (Without manual shuttle shift)
5 828-8140 1 BOLT, Hex, M8 x 140, 10.9, BOLT – hex, 8 – 1.25 x 140 mm, class 10.9 (With manual shuttle shift)
6 862-8055 3 SCREW, Hex Soc Hd, M8 x 55, 12.9, BOLT – hex socket, 8 – 1.25 x 55 mm, class 12.9
8 861-8070 4 SCREW, Hex Soc Hd, M8 x 70, 12.9, BOLT – hex socket, 8 – 1.25 x 70 mm, class 12.9
9 862-6070 1 SCREW, Hex Soc Hd, M6 x 70, 12.9, BOLT – hex socket, 6 – 1.0 x 70 mm, class 12.9
10 828-8120 3 BOLT, Hex, M8 x 120, 10.9, BOLT – hex, 8 – 1.25 x 120 mm, class 10.9
11 828-8140 8 BOLT, Hex, M8 x 140, 10.9, BOLT – hex, 8 – 1.25 x 140 mm, class 10.9
12 814-10175 2 SCREW, BOLT – hex, 10 – 1.5 x 175 mm
13 813-10065 3 BOLT, Hex, M10 x 65, 8.8, BOLT – hex, 10 – 1.5 x 65 mm
14 814-10055 4 BOLT, Hex, M10 x 55, 8.8
1 1997446C2 1 SHAFT ASSY., input, Includes: Ref. 2, 3, 4
2 187516A1 4 PLUG, expansion, replaces 1342852C1 plug
3 38-3605 5 PIN, 3/32″ x 5/16″, Coiled
4 1963874C1 1 PIN, coiled, 8 x 14 mm
8 1286040C2 1 RING, support
9 1997888C1 1 WASHER, THRUST
10 80909C1 2 BEARING, NEEDLE, needle, caged
11 1285977C1 1 GEAR, GEAR – driver, medium
12 1285979C1 1 PINION, GEAR – drive, 52 teeth, high range
13 1286052C1 2 RING, seal, clutch
14 1286043C1 4 WASHER, THRUST
18 572182R1 2 BEARING, THRUST, needle
19 93350C1 6 RING, retaining
20 1286012C2 26 WASHER, Belleville spring
21 1285972C2 2 HOUSING, CLUTCH, CARRIER –
22 1286081C1 2 O-RING, piston, low clutch inner
23 1286076C1 2 RING, piston, clutch, shift
24 1285998C1 2 PISTON, clutch, shift
25 1286083C1 2 O-RING, piston, low clutch outer
26 1286079C1 2 RING, piston, shift
27 93129C1 6 WASHER, Belleville spring
30 93190C1 2 DISC, reaction
31 92935C5 20 DISC, friction
32 92934C2 18 DISC, separator
33 1342854C2 2 DISC, backing, 16.5 mm (21/32 inch) thick, if used
33 1342645C3 2 DISC, CLUTCH, backing, powder metal, 9.7 mm (3/8 inch) thick, if used
34 1285996C1 2 RING, SNAP, retaining
35 1285971C1 1 GEAR, DRIVING, GEAR – driver, 22 teeth, low range
36 A75211 1 BEARING, CONE, tapered roller
37 A75210 1 BEARING, CUP, tapered roller
38 116797C2 1 RING, seal
39 ST2063 1 BEARING, CONE, tapered roller
40 54404R1 1 BEARING, CUP, tapered roller
44 281696A1 1 SUPPORT, bearing, replaces 1285995C2 support
45 814-12050 6 BOLT, Hex, M12 x 50, 8.8
46 1286025C1 4 RING, sealing
47 1342729C1 1 HOUSING, BEARING, bearing
49 613-10030 3 BOLT, Hex, M10 x 30, 8.8, Full Thd, BOLT – hex, full threads, 10 – 1.5 x 30 mm
1 1997446C2 1 SHAFT ASSY., ASSEMBLY – input, see Figure 6-40 for pins and plugs
2 1342729C1 1 HOUSING, BEARING, bearing
3 101-11225 1 RING, SNAP, #225, Ext
4 1286027C2 1 RING, retaining
10 1342240C1 1 HOUSING, CLUTCH, CARRIER –
11 93138C1 1 RING, PISTON, piston
12 92562C1 1 RING, seal
13 93137C1 1 RING, PISTON, piston
14 92561C1 1 RING, piston
15 112299A2 1 PISTON ASSY, clutch
18 93136C2 16 SPRING, clutch
19 112329A1 1 RETAINER, spring
21 100-11306 1 RING, SNAP, #306, Ext
22 92555C1 1 RING, seal
23 235913A2 1 HUB, clutch, replaces 13422141C1 hub
27 100-11200 1 RING, SNAP, #200, Ext
31 1285974C1 9 PLATE, BRAKE, PLATE – separator
32 1285975C2 9 DISC, CLUTCH, friction
33 1963890C1 1 DISC, backing
34 1963876C1 1 RING, SNAP
39 1286088C1 1 TUBE, rear, medium clutch
40 1286089C1 1 TUBE, rear, high clutch
41 1342730C1 2 TUBE, pressure, clutch
43 218-5105 1 ELBOW, 90є, 9/16″-18, 37є x 9/16″-18, O-Ring, 90 degree, 9/16-18 inch flare x adj O-ring boss
45 1963935C2 1 TUBE, lube, gear
44 237-6006 1 O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
1 1954059C2 1 SHAFT, ASSEMBLY – counter, Includes: Ref. 2
2 38-3605 3 PIN, 3/32″ x 5/16″, Coiled
3 D63322 1 BEARING, NEEDLE, roller
4 144348C1 1 RING, SNAP
5 1286012C2 13 WASHER, Belleville spring
8 1286043C1 2 WASHER, THRUST
9 572182R1 1 BEARING, THRUST, needle
10 101-11250 1 RING, SNAP, #250, 2.356, Ext
11 1285978C1 1 PINION, GEAR – driven, 39 teeth, medium range
12 1286052C1 1 RING, seal
13 1285980C1 1 PINION, GEAR – driven, 24 teeth, high range
14 1286041C2 1 SPACER, gear
15 1285990C1 1 PINION, GEAR – driver, 23 teeth, constant mesh
18 84986C1 1 BEARING, CONE, tapered roller
19 40435 1 BEARING, CUP, tapered roller bearing
20 1286042C1 4 WASHER, THRUST
21 K620185 2 BEARING, THRUST, needle, thrust
22 1285968C3 1 GEAR, driven, 54 teeth, low range, replaces 227990A1 gear
22 297134A1 1 GEAR, driven, 54 teeth, low range with teflon grooves, uses sealing ring 297418A2
23 1286077C1 1 RING, driven
24 1286081C1 1 O-RING, piston, low clutch inner
25 1285999C2 1 PISTON ASSY., clutch, low
26 1286079C1 1 RING, piston, shift
27 1286083C1 1 O-RING, piston, low clutch outer
30 93129C1 3 WASHER, Belleville spring
31 93190C1 1 DISC, reaction
32 92935C5 13 DISC, friction
33 92934C2 12 DISC, separator
34 1342854C2 1 DISC, backing, 16.5 mm (21/32 inch) thick, if used
34 1342645C3 1 DISC, CLUTCH, backing, powdered metal, 9.7 mm (3/8 inch) thick, if used
35 1285996C1 1 RING, SNAP, retaining
36 1286028C2 2 RING, gear
39 80907C1 2 BEARING, NEEDLE, caged
40 93269C1 1 SPACER, bearing
41 1286038C1 1 SPACER, bearing
42 287679C1 1 BEARING, ROLLER, CONE – tapered
43 1968297C1 1 BEARING, CUP, tapered roller
44 1342622C1 1 HOUSING, BEARING, bearing, Includes: Ref. 45
45 1286084C1 1 PIN, dowel, 12 x 11 mm
47 613-10030 4 BOLT, Hex, M10 x 30, 8.8, Full Thd, BOLT – hex, full threads, 10 – 1.5 x 30 mm
51 1286087C1 1 TUBE, rear, low clutch
52 297418A2 1 SEAL, RING – cast iron, used with 297134A1 driven gear, not shown
1 94616C2 1 GEAR, BEVEL, SET – and shaft, pinion, Includes: Ref. 2
2 92825C1 1 PLUG, shaft
3 1285991C2 1 PINION, GEAR – driven, 46 teeth, constant mesh
4 1286039C1 1 SPACER, bearing
5 143906C1 1 RING, SNAP, retainer
6 921684C1 1 BEARING, CONE, tapered roller
7 1068264C1 1 CAGE, bearing, Includes: Ref. 8
8 921683C1 1 BEARING, CUP, tapered roller
10 120965C1 1 RING, SNAP, retaining
11 108326H 1 BEARING, CUP, tapered roller
12 94666C1 1 BEARING, CONE, tapered roller
18 566-12035 6 SCREW, 12 Pt Hd, M10 x 35, 12.9, BOLT – 12 point flanged
19 1251958C1 6 WASHER, flat
2 1997705C1 1 CAGE, CASE – differential, right
3 137023A1 6 DOWEL, PIN – 10 x 60 mm, hardened
4 148939C1 2 SEAL, RING
7 1259633C2 1 GEAR, pinion, 20 teeth, differential
8 92905C1 4 PINION, GEAR – bevel, differential, 10 tooth
9 1259634C2 1 PINION, GEAR – lock, bevel, 20 teeth
10 92767C1 1 WASHER, thrust
11 92768C1 1 WASHER, thrust
12 92718C2 4 WASHER, thrust
13 92906C1 2 SHAFT, SHORT, pinion, long
14 92907C1 1 SHAFT, pinion, short
Pages: 1 2 3 4

Leave a Reply

Your email address will not be published. Required fields are marked *