CASE IH Magnum tractor 8940

      No Comments on CASE IH Magnum tractor 8940

CASE IH Magnum tractor 8940 — parts list, part 4 of 4

Assemblies on this page: Parts list (continued) … Parts list (continued).

Parts list (continued)

Pos Part no. Qty Description
95 237-6008 2 O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
96 G108724 1 BACK-UP RING
97 1971475C1 1 PLUG, lock check, Includes: Ref. 98-101
98 237-6008 1 O-RING, 8-1, 90 Duro, .644″ ID x .087″ Thk
99 G110295 1 O-RING, -013, 90 Duro, .426″ ID x .070″ Thk, poppet
100 G110287 1 BACK-UP RING, inner
61 238-6021 1 O-RING, -021, 90 Duro, .926″ ID x .070″ Thk
1 1994576C1 1 BODY, VALVE
2 1543329C1 1 POPPET, VALVE, PLUG –
3 1994581C1 1 SPRING, load check
4 237-6010 1 O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
5 1543357C1 1 WASHER, flat
6 218-1279 1 NUT, LOCK, Blkhd, 7/8″-14, hex, lock, 7/8 inch NF
7 1542500C1 1 BODY, plug
8 9625178 1 PLUG, Hex Soc, 9/16″-18 ORB, Incl. Ref. 9
10 1994577C1 1 SLEEVE VALVE
12 1980302C2 1 ROD, ASSEMBLY – adjusting, Includes: Ref. 13
13 138-56 1 PIN, LOCK, 1/8″ x 11/16″, Slotted
14 G101066 1 SEAL, oil
15 1980226C1 1 PLUG, adjusting
16 1980227C1 1 PLUG, NUT – compression
17 G108956 1 RACE, bearing
18 G108957 1 RACE, bearing
19 237-6010 1 O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
20 1986628C1 5 O-RING, 3/8 ID x 9/16 inch wide
21 F13537 1 BEARING, thrust
22 238-6117 3 O-RING, -117, 90 Duro, .799″ ID x .103″ Thk
23 238-6112 1 O-RING, -112, 90 Duro, .487″ ID x .103″ Thk
24 1994612C1 2 STUD, 12 x 225 mm
24 1994613C1 2 STUD, 12 x 268 mm
24 1986938C1 2 STUD, 12 x 312 mm
25 201-900 1 CAP, 11/16″-16 ORFS, CAP – hex, 11/16-16 inch face seal
26 238-6012 1 O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
27 201-101 1 CONNECTOR, HYD., 11/16″-16 ORFS x 9/16″-18 ORB, ADAPTER – straight, 11/16-16 face seal x
29 238-6012 1 O-RING, -012, 90 Duro, .364″ ID x .070″ Thk
9 237-6006 1 O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
28 237-6006 1 O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
2 93329C2 1 SPRING, retainer
3 93328C3 2 CARTRIDGE, coupler
4 93330C1 2 SPRING, VALVE, tension
5 100-28162 2 RING, SNAP, 1.625″, Int, #162
6 238-5027 4 O-RING, -027, 70 Duro, 1.301″ ID x .070″ Thk
7 93332C1 4 SEAL ASSY., oil, slipper
8 A47221 2 SEAL, RING
2 201-103 2 CONNECTOR, HYD., 1″-14 ORFS x 7/8″-14 ORB, Includes Ref. 3, 4
3 237-6010 1 O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk, Boss end
4 238-6016 1 O-RING, -016, 90 Duro, .614″ ID x .070″ Thk, Face end
5 238-6117 6 O-RING, -117, 90 Duro, .799″ ID x .103″ Thk
6 238-6112 2 O-RING, -112, 90 Duro, .487″ ID x .103″ Thk
7 1994613C1 2 STUD, 12 x 268 mm
8 1334559C2 1 STUD, 10 x 275 mm
9 829-1312 2 NUT, M12 x 1.75, Cl 10
10 829-1310 1 NUT, M10, Cl 10, Hex, Class 10.9
11 102219A1 1 PIPE, TUBE – raise, third circuit
12 102220A2 1 PIPE, TUBE – drop, third circuit
13 1289355C1 1 SUPPORT ASSY., tube
14 486004R1 1 CLAMP, tube
15 224968C2 1 STRIP, CLAMP – isomount
16 828-8040 1 BOLT, Hex, M8 x 40, 10.9, BOLT – hex, 8 – 1.25 x 40 mm, class 10.9
17 832-41308 1 NUT, M8 x 1.25, Cl 10, hex, self-locking, 8 mm – 1.25, class 10.9
18 102519A1 1 SUPPORT, BRACKET – coupler, right-hand
19 628-16030 2 BOLT, Hex, M16 x 30, 10.9, Full Thd, Bolt, Hex, M16 x 30, 10.9, Full Thd
20 103866A2 1 COUPLING, ASSEMBLY – quick disconnect, parts list Fig. 8-062
21 201-306 2 ELBOW, 90є, 1″-14 x 7/8″-14 Adj, ORFS, 90 degree, 1-14 face seal x 7/8-14 inch adj O-ring boss
22 237-6010 1 O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk, Boss end
23 238-6016 1 O-RING, -016, 90 Duro, .614″ ID x .070″ Thk, Face end
24 628-12020 2 BOLT, Hex, M12 x 20, 10.9, Full Thd, BOLT – hex, full threads, 12 – 1.75 x 20 mm, class 10.9
25 217-430 1 PLUG, Hex Soc, 1/8″-27
26 221-1101 1 FITTING, NIPPLE – straight, 1/8 PT x 3/4 inch
27 1348264C1 1 CLAMP, HOSE, 3/8 inch
28 106514A1 1 HOSE, LARGE, 808 mm (30-13/16 inch) long, coupler drain
29 L18337 1 STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch
30 1289481C1 1 ELBOW, 90 degree
31 1334641C1 1 HOSE ASSY., 330 mm (13 inch) long, cut from 427683C1 bulk hose, coupler, elbow to tee
32 1289479C1 1 TEE, barbed, used on models with hitch
33 1289484C1 1 HOSE ASSY., 115 mm (4-9/16 inch) long, cut from 427683C1 bulk hose, drain, tee to tee
34 1334583C3 1 DECAL, 3 ISO, third coupler
35 1334586C1 1 PLUG, ADAPTER – coupler drain, special, Includes: Ref. 36
36 238-6116 1 O-RING, -116, 90 Duro, .737″ ID x .103″ Thk
37 103871A1 2 CAP, PLUG – dust, coupler
40 104301A1 1 COVER, DOOR, coupler
41 104302A1 1 PLATE, retaining
42 104303A1 1 SCREW, BOLT – shoulder
43 461-4258 1 SCREW, Hex Soc Flat Hd, 1/4″-20 x 1/2″, BOLT – hex socket, 1/4 NC x 1/2 inch
44 110947A1 1 WASHER, flat, special
45 110945A1 1 SPRING, coupler door
2 238-6117 6 O-RING, -117, 90 Duro, .799″ ID x .103″ Thk
3 238-6112 2 O-RING, -112, 90 Duro, .487″ ID x .103″ Thk
4 1986938C1 2 STUD, 12 x 312 mm
5 1334613C2 1 STUD, 10 – 1.5 x 312 mm
6 201-103 2 CONNECTOR, HYD., 1″-14 ORFS x 7/8″-14 ORB, Includes Ref. 7, 8
7 237-6010 1 O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk, Boss end
8 238-6016 1 O-RING, -016, 90 Duro, .614″ ID x .070″ Thk, Face end
9 201-306 2 ELBOW, 90є, 1″-14 x 7/8″-14 Adj, ORFS, 90 degree, 1-14 face seal x 7/8-14 inch adj O-ring boss
10 237-6010 1 O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk, Boss end
11 238-6016 1 O-RING, -016, 90 Duro, .614″ ID x .070″ Thk, Face end
12 102221A1 1 PIPE, TUBE – raise, fourth valve
13 102222A1 1 PIPE, TUBE – drop, fourth valve
14 1334203C1 1 SUPPORT ASSY., tube
15 815-8070 1 BOLT, Hex, M8 x 70, 8.8, BOLT – hex, 8 – 1.25 x 70 mm
16 486004R1 2 CLAMP, tube
17 224968C2 2 STRIP, CLAMP – isomount strip
18 832-41308 1 NUT, M8 x 1.25, Cl 10, hex, self-locking, 8 mm – 1.25, class 10.9
19 120012C1 1 SUPPORT, coupler
20 614-12025 2 BOLT, Hex, M12 x 25, 8.8, Full threads, At third circuit coupler
21 103866A2 1 COUPLING, ASSEMBLY – quick disconnect, parts list Figure 8-62
22 221-1101 1 FITTING, NIPPLE – straight, 1/8 PT x 3/4 inch
23 1272764C1 1 SEAL ASSY., drain
24 1334586C1 1 PLUG, ADAPTER – coupler drain, special, Includes: Ref. 25
25 238-6116 1 O-RING, -116, 90 Duro, .737″ ID x .103″ Thk
26 1289480C1 1 TEE, barbed, at third circuit coupler
27 1289484C1 1 HOSE ASSY., 115 mm (4-9/16 inch) long, cut from 427683C1 bulk hose, drain, elbow to tee
28 1334584C3 1 DECAL, 4 ISO, fourth coupler, shown on Figure 9-108
29 103871A1 2 CAP, PLUG – dust, coupler
31 1289481C1 1 ELBOW, 90 degree, special
32 628-16030 2 BOLT, Hex, M16 x 30, 10.9, Full Thd, Bolt, Hex, M16 x 30, 10.9, Full Thd, replaces 628-12020 bolt
33 217-430 1 PLUG, Hex Soc, 1/8″-27
38 110947A1 1 WASHER, flat, special
2 111793A1 1 BUSHING, LARGE, BEARING – control lever
3 111795A1 1 NUT, bearing
5 111793A1 1 BUSHING, LARGE, BEARING – control lever
6 111795A1 1 NUT, bearing
8 111793A1 1 BUSHING, LARGE, BEARING – control lever
9 111795A1 1 NUT, bearing
11 111793A1 1 BUSHING, LARGE, BEARING – control lever
12 111795A1 1 NUT, bearing
14 111934A2 1 SHAFT, pivot, handle
16 1999689C1 1 SUPPORT, pivot
17 1999940C1 1 HOLDER, SUPPORT – cable, flow control
18 1999944C3 1 PLATE ASSY., selector valve
19 825-1408 10 NUT, M8, Cl 8
20 1283979C1 1 BRACKET, mounting, rear
21 495-11034 8 WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch
22 614-8016 2 BOLT, Hex, M8 x 16, 8.8
23 832-10408 1 NUT, LOCK, M8 x 1.25, Cl 8
27 814-8140 1 BOLT, Hex, M8 x 140, 8.8
28 96829C1 1 PIN, AXLE, lock, neutral
29 614-6012 2 BOLT, Hex, M6 x 12, 8.8
30 896-11006 2 WASHER, M6 x 13 x 2, HT
33 96851C2 1 LEVER, neutral, lockout
34 565-107 1 SCREW, Hex Soc Hd, M4 x 20, 8.8, BOLT – hex socket, 4 – .7 x 20 mm
35 1251730C2 1 WASHER, friction, lockout lever
36 96963C2 1 SPACER, lever
37 832-10404 1 NUT, LOCK, M4 x .7, Cl 8, hex, self-locking, 4 mm – 0.7
38 895-11004 1 WASHER, M4, flat, 4.4 x 9 x 0.8 mm
39 127123A1 2 LEVER, float lockout, first and second remote
40 127124A1 2 LEVER, float lockout, third and fourth remote
51 1283978C1 1 BRACKET, mounting, front
52 1283976C4 1 SUPPORT, PLATE – valve
53 614-8020 3 BOLT, Hex, M8 x 20, 8.8
55 122662A3 2 CABLE, flow control, No. 1 and No. 2
56 122663A3 1 CABLE, flow control, No. 3
57 122664A3 1 CABLE, flow control, No. 4
58 A160814 2 KNOB, flow control, tractors without in-cab flow control
60 484-21010 2 SET SCREW, Hex Soc, #10-32 x 5/8″, set, hex socket, No. 10 NF x 5/8 inch, tractors without in-cab
1 1272400C1 1 COUPLING, self sealing, female
2 1954133C1 1 DUST CAP, coupling, dust, Includes: Ref. 2A
3 1348201C1 1 SUPPORT, BRACKET – return line, if used
4 A66788 1 CLAMP, U-BOLT – 1-13/32 x 2 x 1/4 inch NC
5 425-104 4 NUT, 1/4″-20, G5
6 492-11025 2 WASHER, LOCK, 1/4″
9 201-107 1 CONNECTOR, HYD., 1 3/16″-12 ORFS x 7/8″-14 ORB, ADAPTER – straight, 1-3/16-12 face seal x
10 238-6018 1 O-RING, -018, 90 Duro, .739″ ID x .070″ Thk
11 237-6010 1 O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
12 1348302C1 1 HOSE, 2075 mm (81-11/16 inch) long, oil return
13 201-428 1 TEE, 1 3/16″-12 x 1 1/16″-12 Run, ORFS, 1-3/16-12 face seal branch x face seal x 1-1/16-12 inch adj
14 238-6018 2 O-RING, -018, 90 Duro, .739″ ID x .070″ Thk
15 237-6012 1 O-RING, 12-1, 90 Duro, .924 ID x .118″ Thk
18 515-23302 1 CLAMP, 1 3/16″, Insul, 3/8″ Bolt, P-type, 1-3/16 inch ID
19 614-8020 1 BOLT, Hex, M8 x 20, 8.8
20 825-1408 1 NUT, M8, Cl 8
22 1342123C2 1 HOSE, return, 967 mm (38-1/8 inch) long, steering
7 627-8025 1 BOLT, Hex, M8 x 25, 10.9
2 1331849C1 1 BUSHING, rockshaft, left-hand
3 1331848C1 1 BUSHING, rockshaft, right-hand
4 76349 2 PLUG, Hex Hd, 9/16″-18 ORB, (Without hitch)
6 86512512 1 PLUG, Hex Hd, 7/8″-14 ORB, (Without hitch)
7 237-6010 1 O-RING, 10-1, 90 Duro, .755″ ID x .097″ Thk
8 380174R1 1 PLUG, Cup, 3.510″, cup, 3-33/64 inch OD (Without hitch)
9 380173R1 1 PLUG, Cup, 3.762″, cup, 3-49/64 inch OD
10 380263R1 4 PLUG, cup, without hitch
11 1342165C1 1 LEVER, link, potentiometer
12 413-416 1 BOLT, Hex, 1/4″-20 x 1″, G5
13 492-11025 1 WASHER, LOCK, 1/4″
16 614-16100 16 BOLT, Hex, M16 x 100, 8.8, Full Thd, BOLT – hex, full threads, 16 – 2.0 x 100 mm
17 1347918C1 1 SEAL, oil, rockshaft, left-hand
18 1347919C1 1 SEAL, oil, rockshaft, right-hand
19 380264R3 1 GASKET, rear frame cover
20 1973956C1 1 ROCKSHAFT, hitch control
21 84923C3 1 ARM, BELLCRANK – rockshaft
22 382811R1 1 SCREW, special, rockshaft bellcrank
23 84922C1 1 ROD, piston connecting
24 38-12840 1 PIN, LOCK, 7/16″ x 2 1/2″, Slotted, 7/16″ x 2 1/2″, Slotted, if used
24 38-12848 1 PIN, LOCK, 7/16″ x 3″, Slotted, 7/16″ x 3″, Slotted, if used
26 1340665C1 1 SUPPORT, BRACKET – potentiometer
27 614-10035 1 BOLT, Hex, M10 x 35, 8.8, Full Thd
29 832-10410 1 NUT, LOCK, M10 x 1.5, Cl 8
36 492-21062 1 WASHER, LOCK, 5/8″, 5/8″, right-hand
37 38-11616 1 PIN, LOCK, 1/4″ x 1″, Slotted
38 1340669C1 1 LEVER, sensor, rockshaft
39 413-1024 1 BOLT, Hex, 5/8″-11 x 1 1/2″, G5, Full Thd, Rockshaft arm, RH
39 413-1020 1 BOLT, Hex, 5/8″-11 x 1 1/4″, G5, Full Thd, Rockshaft arm, LH
40 1286931C3 1 LINK, LOWER, ARM ASSEMBLY – rockshaft, left-hand, includes item 41, prior to serial number
40 1286930C5 1 LINK, LOWER, ARM ASSEMBLY – rockshaft, right-hand, shown, prior to serial number JJA0094169, if
41 1252114C1 2 BUSHING, pivot
42 145474C1 2 PIN, LARGE, cylinder mounting
43 838-3655 2 PIN, roll, 6 x 55 mm
44 388574R1 2 WASHER, rockshaft arm retaining
45 1342171C2 1 ROD ASSY., link, potentiometer
46 814-6055 4 BOLT, Hex, M6 x 55, 8.8, BOLT – hex, 6 – 1.0 x 55 mm
47 825-5146 4 NUT, M6, Flg Ser
50 1340666C1 1 HOUSING, potentiometer
51 1348212C1 1 SHAFT, potentiometer sensor, see Figure 4-20
52 493-81008 2 WASHER, LOCK, Int Tooth, 5/16″, internal tooth lock, 5/16 inch
53 495-11034 2 WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch
54 425-115 1 NUT, 5/16″-24, G5
55 L18337 1 STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch
56 413-616 1 BOLT, Hex, 3/8″-16 x 1″, G5, Full Thd
57 492-11038 1 WASHER, LOCK, 3/8″
60 110451A1 1 LINK, LOWER, ARM ASSEMBLY – rockshaft, left-hand, serial number JJA0094169 and after, if used
60 110452A1 1 LINK, LOWER, ARM ASSEMBLY – rockshaft, right-hand, serial number JJA0094169 and after, if used
61 110447A2 2 PIN, HITCH, rockshaft with flag, Part of Heavy Duty Lift Link Kit P/N 299255A1
62 D95748 2 SPACER, , Part of Heavy Duty Lift Link Kit P/N 299255A1
63 896-11010 2 WASHER, M10 x 21.5 x 2.5, HT, , Part of Heavy Duty Lift Link Kit P/N 299255A1
64 627-10020 2 BOLT, Hex, M10 x 20, 10.9, Full Thd, , Part of Heavy Duty Lift Link Kit P/N 299255A1
65 1286923C2 1 ARM, ASSEMBLY – rockshaft, left-hand, includes item, 41, if used
28 895-11010 1 WASHER, M10 x 20 x 2
5 237-6006 1 O-RING, 6-1, 90 Duro, .468″ ID x .078″ Thk
1 1266971C4 1 BRACKET, HITCH, link mounting
2 1286840C7 1 PIN, HITCH, upper link bracket
3 1978738C1 1 PIN, SPLIT (COTTER), cotter, hair, 3/16 inch
4 828-20080 6 BOLT, Hex, M20 x 80, 10.9
5 1954221C2 1 LINK, TURNBUCKLE – upper, used with 1331854C1 link assembly, no longer available order
6 1331863C2 1 HANDLE, turnbuckle
7 1981986C1 1 END, ROD – upper link, right-hand thread, without keyway
8 219-87 2 NIPPLE, LUBE, 1/4″-28 x .56″ lg, Self-Tap, Replaces 219-14 fitting
9 1978738C1 1 PIN, SPLIT (COTTER), cotter, hair, 3/16 inch, used with 1954221C2 turnbuckle
10 427-6200 1 PIN, CLEVIS, 3/8″ x 2″, 3/8 x 2 inch, hardened
11 432-612 1 PIN, SPLIT (COTTER), 3/32″ x 3/4″
12 1282063C2 1 END, ROD – upper link, left-hand thread
13 838-3638 2 PIN, M6 x 38, Coiled, roll, 6 x 38 mm
14 1954223C2 1 ARM, TURNBUCKLE – 1-3/4″ thread, upper link, used with 1331855C1 link assembly, no longer
15 1331863C2 1 HANDLE, turnbuckle
16 1981988C1 1 END ASSY., SCREW – 1-3/4″ thread, includes ball, right-hand thread, without keyway
17 219-87 2 NIPPLE, LUBE, 1/4″-28 x .56″ lg, Self-Tap, Replaces 219-14 fitting
18 1978738C1 1 PIN, SPLIT (COTTER), cotter, hair, 3/16 inch, used with 1954223C2 turnbuckle
19 427-6200 1 PIN, CLEVIS, 3/8″ x 2″, 3/8 x 2 inch, hardened
20 432-612 1 PIN, SPLIT (COTTER), 3/32″ x 3/4″
21 1282082C2 1 END, SCREW ASSEMBLY – includes ball, left-hand thread
22 838-5645 2 PIN, LOCK, M6 x 45, Slotted, roll, 6 x 45 mm
23 149836C4 2 TURNBUCKLE, lift link
25 1266968C1 2 YOKE, lift link, prior to serial number JJA0094169
26 39-51260 2 PIN, HEADED, 3/4″ x 3 3/4″, headed, 3/4 x 3-3/4 inch
27 123464C3 2 CLAMP, turnbuckle lock
28 149838C1 2 ROD, leveling
29 413-652 2 BOLT, Hex, 3/8″-16 x 3 1/4″, G5
30 495-11041 4 WASHER, 3/8″, SAE, Flat, (13/32 x 13/16 x 1/16″)
31 231-4116 2 NUT, LOCK, 3/8″-16, GB, hex, self-locking, 3/8 inch NC
33 219-23 2 NIPPLE, LUBE, 1/4″-18 NPT x .88″ lg, FITTING – grease, straight, 1/4 PT x 7/8 inch
34 38-11620 2 PIN, 1/4″ x 1 1/4″, Slotted, 1/4″ x 1 1/4″, Slotted
35 221-841 2 PLUG, hex socket, 1/4 inch PT
36 480523R1 2 SPLIT PIN/SAFETY PIN, hair
37 1266969C1 2 PIN, AXLE, head, 19 mm (3/4 inch) diameter, prior to serial number JJA0094169
38 242747A1 2 BOLT, PIN – leveling, replaces 109088C4 pin
40 1286725C2 2 BRACKET, PIVOT, SWIVEL ASSEMBLY – lift link, with one grease fitting and two bushings, includes
41 1252114C1 2 BUSHING, lift link swivel
42 24512R1 2 PIN, HEADED, 3/4″ x 4 3/4″, clevis, 3/4 x 4-3/4 inch, prior to serial number JJA0094169
43 1272669C2 2 PIVOT, SWIVEL ASSEMBLY – lift link, with two grease fittings and four bushings, if used, prior to serial
44 1252114C1 4 BUSHING, lift link swivel, 19.3 (3/4) ID x 25.5 (1) x 23.5 mm (15/16 inch) long
45 219-14 2 NIPPLE, LUBE, 1/4″ x .56″ lg, Drive, grease, straight, 1/4 drive type x 9/16 inch
46 294767A1 2 PIVOT, SWIVEL ASSEMBLY – lift link, with two grease fittings and four bushings, if used, serial
47 294770A1 4 BUSHING, LARGE, pivot, 25.5 (1) ID x 28.9 (1-1/8) OD x 19 mm (3/4 inch) long, Part of Heavy Duty
48 219-87 2 NIPPLE, LUBE, 1/4″-28 x .56″ lg, Self-Tap
1 1331893C8 1 ROD, LIFTING, LINK – lower lift, left-hand front, telescoping, not shown, if used
1 1331894C8 1 ROD, LIFTING, LINK – lower lift, right-hand front, telescoping, if used
2 134313A3 1 LINK, LOWER, lift, left-hand, rigid, not shown, if used
2 134318A3 1 LINK, LOWER, lift, right-hand, rigid, if used
3 1282114C4 1 LINK, LOWER, lift, left-hand rear, not shown
3 1282115C4 1 LINK, LOWER, lift, right-hand rear
4 1286752C2 2 BLOCK, BUMPER – cam
5 70479C1 2 SHIM, 1/32 inch, bumper
6 70480C1 12 SHIM, 1/16 inch, bumper
7 1266811C1 2 SPACER, cam bumper
8 738-31260 2 PIN, M12 x 60, Coiled, roll, 12 x 60 mm
9 413-1280 2 BOLT, Hex, 3/4″-10 x 5″, G5, hex, 3/4 NC x 5 inch
10 231-14412 2 NUT, LOCK, 3/4″-10, GB, hex, self-locking, 3/4 inch NC
11 495-11081 2 WASHER, 3/4″, SAE
15 1347900C3 1 SUPPORT ASSY., BRACKET – lower link, left-hand, not shown, includes item 16, 1960223C1 bushing
15 1347902C3 1 SUPPORT ASSY., BRACKET – lower link, right-hand
16 1960223C1 2 BUSHING, bracket
17 828-16090 2 BOLT, Hex, M16 x 90, 10.9
18 896-16016 2 WASHER, M16 x 34.5 x 5, HT, flat, 17.5 x 34 x 5 mm, hardened
19 1347983C1 2 BUSHING, LARGE, bracket
20 614-10020 2 BOLT, Hex, M10 x 20, 8.8, Full Thd
26 1998150C1 2 SPACER, cylinder mounting
27 1998013C1 2 BUSHING, cylinder
28 145678C3 2 WASHER, flat, 17 mm
29 828-16160 2 BOLT, Hex, M16 x 160, 10.9, BOLT – hex, 16 – 2.0 x 160 mm, class 10.9
30 495-81206 2 WASHER, 1 9/32″ x 2 1/2″ x .120″, flat, 1-9/32 x 2-1/2 x 7/64 inch
34 1347904C1 2 PLATE, LARGE, sensing pin retaining
35 895-18010 6 WASHER, M10 x 18 x 1.6
36 614-10020 6 BOLT, Hex, M10 x 20, 8.8, Full Thd
40 828-24110 4 BOLT, Hex, M24 x 110, 10.9, BOLT – hex, 24 – 3.0 x 110 mm, class 10.9
41 896-16024 4 WASHER, M24 x 56.5 x 6, HT, flat, 26 x 56 x 6 mm
45 398399R1 2 LATCH, lower link
46 382192R1 2 SPRING, link latch
47 382193R1 2 SPRING, stiffener
48 614-8012 2 BOLT, Hex, M8 x 12, 8.8, Full Thd, Replaces 414-58 bolt
49 125685A1 2 PIN, LARGE, used with rigid lower link, if used, prior to serial number JJA0094169
50 627-10025 2 BOLT, Hex, M10 x 25, 10.9, Full Thd, BOLT – hex, full threads, 10 – 1.5 x 25 mm, class 10.9, Part of
51 896-11010 2 WASHER, M10 x 21.5 x 2.5, HT
52 D95748 2 SPACER, pin, 13/32 ID x 5/8 OD x 9/32 inch long, prior to serial number JJA0094169
1 70-6430T1 1 ATTACHMENT, HITCH – quick attachment, coupler, 8930/8940/8950
2 70-6452T1 1 PIN, LARGE, mounting, 4-15/16 inch long, center link, 8930/8940/8950
3 70-3082T2 3 PLATE, LARGE, BLOCK – pin retaining, 8930/8940/8950
4 426-816 6 BOLT, Hex, 1/2″-13 x 1″, G8, Full Thd, BOLT – hex, 1/2 NC x 1 inch, grade 8, 8930/8940/8950
9 70-4320T1 2 HANDLE, hitch release, 8930/8940/8950
10 70-4324T1 2 THREADED ROD, LINK – hitch release, 8930/8940/8950
11 70-6310T2 2 TRIGGER, LATCH – hitch release, 8930/8940/8950
12 213-126 2 CLEVIS, ADJUSTABLE, 3/8″-24 x 2 1/2″, adjustable, 3/8 inch NF, 8930/8940/8950
13 427-6106 2 PIN, CLEVIS, 3/8″ x 1 1/16″, 8930/8940/8950
14 432-616 4 PIN, SPLIT (COTTER), 3/32″ x 1″, 8930/8940/8950
15 426-1072 4 BOLT, Hex, 5/8″-11 x 4 1/2″, G8, BOLT – hex, 5/8 NC x 4-1/2 inch, grade 8, 8930/8940/8950
16 231-42110 4 NUT, LOCK, 5/8″-11, GB, hex, self-locking, 5/8 inch NC, 8930/8940/8950
17 70-4293T1 2 PIN, LARGE, lower hitch, 8930/8940/8950
18 425-156 2 NUT, Jam, 3/8″-24, G5, 8930/8940/8950
19 19-5423 2 PIN, LARGE, clevis, 3/8 x 7/8 inch, 8930/8940/8950
20 70-4340T1 2 SPRING, COMPRESSION, compression, 8930/8940/8950
21 321-3339 1 DECAL, Warning, be certain both latches are fully engaged across the implement lift pins, not shown
23 229035A1 1 PIN, LARGE, upper link, 8930, quick hitch coupler models (if equipped)
24 64715C1 2 HANDLE, hitch release, 8930, quick hitch coupler models (if equipped)
25 427-5112 2 PIN, CLEVIS, 5/16″ x 1 1/8″, clevis, 5/16 x 1-1/8 inch, 8930, quick hitch coupler models (if equipped)
26 432-612 2 PIN, SPLIT (COTTER), 3/32″ x 3/4″, 8930, quick hitch coupler models (if equipped)
27 326-840 8 BOLT, Hex, 1/2″-13 x 2 1/2″, G8, 8930, Quick hitch coupler models (if equipped)
28 392-11050 8 WASHER, LOCK, 1/2″, 1/2″, 8930, quick hitch coupler models (if equipped)
29 329-108 8 NUT, 1/2″-13, G8, 8930, Quick hitch coupler models (if equipped)
30 229992A1 2 LUG, LATCH – hitch release, 8930, quick hitch coupler models (if equipped)
31 229990A1 2 PIN, LARGE, roll, 1/2 x 2 inch, 8930, quick hitch coupler models (if equipped)
32 229993A1 2 PIN, LARGE, roll, 5/16 x 1 inch, 8930, quick hitch coupler models (if equipped)
33 229994A1 2 THREADED ROD, LINK – hitch release, 8930, quick hitch coupler models (if equipped)
34 64717C1 2 SPRING, compression, 8930, quick hitch coupler models (if equipped)
35 229034A1 2 PIN, LARGE, lower link, 8930, quick hitch coupler models (if equipped)
36 D33805 3 PIN, locking, 8930, quick hitch coupler models (if equipped)
37 321-3339 2 DECAL, Warning, be certain both latches are fully engaged across the implement lift pins, not shown
1 1286971C1 1 PLATE ASSY., wear, drawbar
2 896-16016 8 WASHER, M16 x 34.5 x 5, HT, flat, 17.5 x 34 x 5 mm, hardened, replaces 67872C1 washer
3 628-16050 2 BOLT, Hex, M16 x 50, 10.9, Full Thd
4 828-16190 6 BOLT, Hex, M16 x 190, 10.9, BOLT – hex, 16 – 2.0 x 190 mm, class 10.9
7 1981968C2 1 SUPPORT, drawbar
8 1331889C1 1 CAM, sway limiter, left-hand, not shown
8 1331890C1 1 CAM, sway limiter, right-hand
9 410-11228 2 BOLT, Locking, 3/4″-10 x 1 3/4″, G8, BOLT – hex, self-locking, 3/4 NC x 1-3/4 inch, grade 8
10 828-16060 4 BOLT, Hex, M16 x 60, 10.9, Full Thd
11 224619C2 1 SPACER, drawbar pivot
12 142619C3 1 SUPPORT ASSY., pivot, drawbar, Includes: Ref. 13
13 837-25050 1 DOWEL, M25 x 50, dowel, 25 x 50 mm, hardened
14 896-16016 8 WASHER, M16 x 34.5 x 5, HT, flat, 17.5 x 34 x 5 mm, hardened
15 1286969C3 1 DRAWBAR, swinging, single shaft PTO, if equipped
15 227414A1 1 DRAWBAR, swinging, dual shaft PTO, if equipped
16 1982103C1 1 PIN, pivot, drawbar, 140 mm
17 67828C1 1 RETAINER, pin
21 627-12030 1 BOLT, Hex, M12 x 30, 10.9, Full Thd
22 892-11012 1 WASHER, LOCK, M12
23 827-16140 2 BOLT, Hex, M16 x 140, 10.9
24 832-10416 2 NUT, LOCK, M16 x 2, Cl 8
25 1331943C1 1 SUPPORT ASSY., chain
26 827-20090 1 BOLT, Hex, M20 x 90, 10.9
27 896-11020 1 WASHER, M20 x 37.5 x 4, HT, flat, 22 x 37 x 4 mm, hardened
28 829-1420 1 NUT, M20, Cl 10
30 439-11236 2 PIN, HEADED, 3/4″ x 2 1/4″, headed, 3/4 x 2-1/4 inch, replaces 439-51236 pin
31 1978738C1 2 PIN, SPLIT (COTTER), cotter, hair, 3/16 inch
1 142619C3 1 SUPPORT ASSY., pivot, drawbar, Includes: Ref. 2
2 837-25050 1 DOWEL, M25 x 50, dowel, 25 x 50 mm, hardened
3 1982103C1 1 PIN, pivot, drawbar
4 67828C1 1 RETAINER, pin, drawbar
5 892-11012 1 WASHER, LOCK, M12
6 627-12030 1 BOLT, Hex, M12 x 30, 10.9, Full Thd
7 896-16016 4 WASHER, M16 x 34.5 x 5, HT, flat, 17.5 x 34 x 5 mm, hardened
8 828-16060 4 BOLT, Hex, M16 x 60, 10.9, Full Thd
9 1348126C1 1 DRAWBAR, swinging, single shaft PTO, if equipped
9 1348127C1 1 BAR, draw, swinging, dual shaft PTO, if equipped
10 827-16140 2 BOLT, Hex, M16 x 140, 10.9, Single shaft PTO, if equipped
10 827-16130 2 BOLT, Hex, M16 x 130, 10.9, BOLT – hex, 16 – 2.0 x 130 mm, class 10.9, dual shaft PTO, if equipped
11 832-10416 2 NUT, LOCK, M16 x 2, Cl 8
12 1982156C3 1 SUPPORT, BRACKET – rear support
13 1998066C1 2 PIN, drawbar roller
14 23443R1 4 NUT, LOCK, 1″-8, GC, hex, 1 inch NC
15 1982141C1 1 PLATE, LARGE, rear support
16 A145831 2 BUSHING, ROLLER – drawbar
17 1982142C1 1 PLATE, LARGE, front support
18 219-14 2 NIPPLE, LUBE, 1/4″ x .56″ lg, Drive, grease, straight, 1/4 drive type x 9/16 inch
19 828-16065 8 BOLT, Hex, M16 x 65, 10.9
20 896-16016 8 WASHER, M16 x 34.5 x 5, HT, flat, 17.5 x 34 x 5 mm, hardened
21 1286985C4 1 PIN, HITCH, drawbar hitch
22 1286924C1 1 SPACER, strap
23 1331939C1 1 SPACER, strap
24 1331943C1 1 SUPPORT ASSY., chain
25 1348030C1 1 BAR, STRAP – hammerstrap
26 827-20200 1 BOLT, Hex, M20 x 200, 10.9, BOLT – hex, 20 – 2.5 x 200 mm, class 10.9
27 827-20160 1 BOLT, Hex, M20 x 160, 10. 9, BOLT – hex, 20 – 2.5 x 160 mm, class 10.9
28 896-11020 2 WASHER, M20 x 37.5 x 4, HT, flat, 22 x 37 x 4 mm, hardened
29 829-1420 2 NUT, M20, Cl 10
30 1348043C1 1 PIN, LARGE, klik, lock
31 224619C2 1 SPACER, drawbar pivot
1 1286985C4 1 PIN, HITCH, hammerstrap
2 1289372C1 1 SPLIT PIN/SAFETY PIN, hair, special, if used, drawbar hammerstrap
3 1286983C1 1 RAIL ASSY., SPACER – drawbar strap, if used
4 827-20220 1 BOLT, Hex, M20 x 220, 10.9, BOLT – hex, 20 – 2.5 x 220 mm, class 10.9, if used, drawbar hammerstrap
4 827-20210 1 BOLT, Hex, M20 x 210, 10.9, BOLT – hex, 20 – 2.5 x 210 mm, class 10.9, if used, drawbar hammerstrap
5 896-11020 2 WASHER, M20 x 37.5 x 4, HT, flat, 22 x 37 x 4 mm, hardened, drawbar hammerstrap
6 829-1320 2 NUT, M20, Cl 10, Drawbar hammerstrap
7 1286984C1 1 DRAWBAR, HAMMERSTRAP –
10 1286924C1 1 SPACER, strap, if used
11 1331939C1 1 SPACER, strap, if used
12 1965315C2 1 LEVER, hammerstrap
13 1965312C3 1 LATCH ASSY., hammerstrap
14 1965316C2 2 BUSHING, latch, hammerstrap
15 827-12065 1 BOLT, Hex, M12 x 65, 10.9, hex, 12 – 1.75 x 65 mm, class 10.9, drawbar hammerstrap
16 832-10412 1 NUT, LOCK, M12 x 1.75, Cl 8, Drawbar hammerstrap
17 827-20200 1 BOLT, Hex, M20 x 200, 10.9, BOLT – hex, 20 – 2.5 x 200 mm, class 10.9, drawbar hammerstrap
18 1348043C1 1 PIN, LARGE, klik, lock, special, if used, drawbar hammerstrap
19 1331943C1 1 SUPPORT ASSY., chain, drawbar hammerstrap
20 A181436 1 BOX, TOOL, tool box, Includes: Handle, Pin, and Tray
21 A181434 1 SUPPORT, BRACKET – mounting, tool box
24 814-16150 2 BOLT, Hex, M16 x 150, 8.8, BOLT – hex, 16 – 2.0 x 150 mm, tool box
25 893-16016 2 WASHER, LOCK, Int Tooth, M16, internal tooth lock, 16 mm, tool box
26 895-11016 2 WASHER, M16 x 30 x 3, flat, 17.5 x 30 x 3 mm, tool box
27 825-1416 2 NUT, M16, Cl 8, Toolbox
28 1348536C1 2 SPACER, mounting, tool box
1 246895A1 1 STRAP, hammer, drawbar, offset
2 1348126C1 1 DRAWBAR, swinging, single shaft PTO, if equipped
2 1348127C1 1 BAR, draw, swinging, dual shaft PTO, if equipped
3 284759A1 1 SUPPORT, chain
4 232617A1 1 LATCH, draw pin
5 827-20100 1 BOLT, Hex, M20 x 100, 10.9, BOLT – hex, 20 – 2.5 x 100 mm, class 10.9
6 896-11020 3 WASHER, M20 x 37.5 x 4, HT, flat, 22 x 37 x 4 mm, hardened
7 828-20140 1 BOLT, Hex, M20 x 140, 10.9, hex, 20 – 2.5 x 140 mm, class 10.9
8 829-1420 1 NUT, M20, Cl 10
9 232616A2 1 PIN, HITCH, hammerstrap, special
10 232615A2 1 DRAWBAR, HAMMERSTRAP – Catagory 3
11 277702A1 1 DRAWBAR, swinging, no longer offered, order 294015A2 drawbar below
11 294015A2 1 DRAWBAR, heavy duty
12 233790A1 1 SUPPORT ASSY., chain
13 232617A1 1 LATCH, draw pin
14 827-20150 2 BOLT, Hex, M20 x 150, 10.9
15 896-11020 3 WASHER, M20 x 37.5 x 4, HT, flat, 22 x 37 x 4 mm, hardened
16 829-1420 2 NUT, M20, Cl 10
17 232616A2 1 PIN, HITCH, hammerstrap, special
1 1334670C4 1 SUPPORT, MOUNT – engine, right-hand
2 1334669C4 1 SUPPORT, MOUNT – engine, left-hand
3 626-12035 6 BOLT, Hex, M12 x 35, 10.9, Full Thd, BOLT – hex, full threads, 12 – 1.75 x 35 mm, class 10.9
4 896-15012 6 WASHER, M12 x 28.5 x 4, HT, flat, 13.5 x 28 x 4 mm, hardened
7 1960839C1 1 SUPPORT, BRACKET – engine mount, right-hand
8 1960841C1 1 SUPPORT, BRACKET – engine mount, left-hand
9 627-12040 4 BOLT, Hex, M12 x 40, 10.9, Full Thd
10 895-11012 4 WASHER, M12 x 24 x 2.5, flat, 13.5 x 24 x 2.5 mm
12 826-16100 2 BOLT, Hex, M16 x 100, 10.9, BOLT – hex, M16; 10.9
13 96-81009 4 WASHER, 11/16″ x 1 1/2″ x .134″, HDN
14 825-1416 2 NUT, M16, Cl 8
17 1289057C2 1 RAIL, FRAME – side, right-hand
18 1289056C1 1 RAIL, FRAME – side, left-hand
19 828-22305 2 BOLT, Hex, M22 x 305, 10.9, BOLT – hex, 22 – 2.5 x 305 mm, class 10.9
20 1289069C1 4 WASHER, flat, hardened
21 828-22070 2 BOLT, Hex, M22 x 70, 10.9, BOLT – hex, 22 – 2.5 x 70 mm, class 10.9
22 828-20070 2 BOLT, Hex, M20 x 70, 10.9, Full Thd
23 A177650 4 WASHER, flat, hardened
26 828-16280 2 BOLT, Hex, M16 x 280, 10.9, BOLT – hex, 16 – 2.0 x 280 mm, class 10.9
27 896-16016 2 WASHER, M16 x 34.5 x 5, HT, flat, 17.5 x 34 x 5 mm, hardened
28 A169100 16 BOLT, hex flange 16 – 2 x 45 mm, class 10.9
29 137316A3 1 SUPPORT ASSY., BOLSTER – steering, front end
30 828-20070 2 BOLT, Hex, M20 x 70, 10.9, Full Thd
40 1955424C1 1 PLATE, bolster cover, if used
41 495-11053 2 WASHER, 1/2″, SAE, (17/32″ x 1-1/16″ x 3/32″), If used
42 614-10030 5 BOLT, Hex, M10 x 30, 8.8, If used
43 192896A1 4 PLUG, front support, if used
44 225151A1 1 PROTECTION PLATE, PLATE – bolster cover, if used
45 864-10016 2 SCREW, Hex Soc Hd, M10 x 16, 8.8, If used
46 895-15010 2 WASHER, M11 x 24 x 2, If Used
5 239385A4 1 SUPPORT, FRAME – front weight, maximum of 22 weights
6 827-20100 6 BOLT, Hex, M20 x 100, 10.9, BOLT – hex, 20 – 2.5 x 100 mm, class 10.9
7 896-11020 6 WASHER, M20 x 37.5 x 4, HT, flat, 22 x 37 x 4 mm, hardened
9 1347524C1 6 WEIGHT, front, order 1348233C1 or A67894 weight from Machinery Price List, 45.36 kgs, (100 pound)
10 1347524C1 22 WEIGHT, front, order 1348233C1 or A67894 weight from Machinery Price List, 45.36 kgs, (100 pound)
11 1978431C1 3 CLAMP, weight
12 A169139 3 BOLT, square head, special, 1/2 NC x 3-1/4 inch
13 495-11053 3 WASHER, 1/2″, SAE, (17/32″ x 1-1/16″ x 3/32″)
14 80679 3 WASHER, LOCK, 1/2″
15 425-108 3 NUT, 1/2″-13, G5
16 1979024C1 1 PLATE, CLAMP – weight
17 1979025C1 1 PLATE ASSY., CLAMP – weight
18 256475A1 1 TRUSS ROD, tie, threaded, 22 weight, 32-7/8 inch long, if used, shown
19 495-11053 2 WASHER, 1/2″, SAE, (17/32″ x 1-1/16″ x 3/32″)
20 425-108 3 NUT, 1/2″-13, G5
1 140668A2 1 FRAME, SUPPORT – hood and radiator
2 844-10065 4 BOLT, Hex Flg, M10 x 65, 8.8, BOLT – heavy hex flange, 10 – 1.5 x 65 mm
19 811-10025 4 BOLT, CARRIAGE, Short NK, M10 x 25, Cl8.8, Full Thd
20 829-2410 4 NUT, M10 x 1.5, Flg, Cl 10
21 188762A1 1 SUPPORT ASSY., side panel, left-hand, rear
22 1289062C2 1 SUPPORT ASSY., hood release, left
23 864-10020 2 SCREW, Hex Soc Hd, M10 x 20, 8.8
24 829-2410 2 NUT, M10 x 1.5, Flg, Cl 10
26 1334564C2 1 SUPPORT, BRACKET – side panel, left-hand, rear support, if used
27 811-10025 4 BOLT, CARRIAGE, Short NK, M10 x 25, Cl8.8, Full Thd
28 829-2410 4 NUT, M10 x 1.5, Flg, Cl 10
29 864-10020 2 SCREW, Hex Soc Hd, M10 x 20, 8.8
30 829-2410 2 NUT, M10 x 1.5, Flg, Cl 10
31 1289064C1 1 SUPPORT ASSY., hood release, right
32 614-12030 4 BOLT, Hex, M12 x 30, 8.8, Full threads
33 892-11012 4 WASHER, LOCK, M12
34 142187A1 1 SUPPORT, hood release, with clips, if used
35 1340604C1 1 HANDLE, hood release
36 1960805C4 1 BRACKET, screen latch, inner, right
37 1340590C1 1 SUPPORT, BRACKET – screen latch, inner, left
38 614-8020 1 BOLT, Hex, M8 x 20, 8.8
40 1968039C3 2 FASTENER, RECEIVER – screen, latch stud
41 260-5448 4 SCREW, SELF TAPPING, Cross Pan Hd, #8 x 1/2″, Phillips
42 495-21019 4 WASHER, #8
45 614-10025 2 BOLT, Hex, M10 x 25, 8.8, Full Thd
46 A169954 2 BUSHING, hood release
47 892-11010 2 WASHER, LOCK, M10
48 825-1410 2 NUT, M10, Cl 8
55 825-2308 2 NUT, M8 x 1.25, Flg, Cl 8, hex, flange, 8 mm – 1.25
56 892-11010 2 WASHER, LOCK, M10
57 413-520 2 BOLT, Hex, 5/16″-18 x 1 1/4″, G5
58 425-105 2 NUT, 5/16″-18, G5
59 116292A2 1 SUPPORT, BRACKET – right-hand side panel, rear support
60 A176570 1 SPACER, bracket
61 854-10070 1 BOLT, Hex Flg, M10 x 70, 10.9, Replaces 905-10060 bolt
63 905-10030 1 BOLT, Hex Serr Flg, M10 x 30, BOLT – hex serrated flange, 10 – 1.5 x 30 mm, side panel bracket
64 1334474C1 2 BRACKET, side panel support, front
39 895-11008 1 WASHER, M8 x 16 x 1.6
62 895-11010 1 WASHER, M10 x 20 x 2, If used
1 229424A2 1 SILL, FRAME – hood side, right-hand
1 229425A2 1 SILL, FRAME – hood side, left-hand, not shown
3 230114A1 1 PANEL ASSY., hood, upper, right-hand
3 230115A1 1 PANEL ASSY., hood, upper, left-hand, not shown
6 1334317C2 2 SEAL, foam, adhesive back, 343 mm (13-1/2 inch) long, cut from 1348430C1 bulk seal
7 231857A6 1 HOUSING, grille, upper
8 252763A1 1 GASKET, SEAL – foam, adhesive back, 1040 mm (41 inch) long, upper grille, cut from 252768A1 bulk
10 413-412 2 BOLT, Hex, 1/4″-20 x 3/4″, G5, Full Thd
11 495-21031 20 WASHER, 1/4″, flat, 5/16 x 3/4 x 1/16 inch
12 231-1444 20 NUT, LOCK, 1/4″-20, GB
14 A147030 2 SPACER, SPACER – grille screen, not shown
15 181461A1 1 PANEL ASSY., HOOD – top center, screen
16 495-21031 18 WASHER, 1/4″, flat, 5/16 x 3/4 x 1/16 inch
17 231-1444 18 NUT, LOCK, 1/4″-20, GB
26 413-412 6 BOLT, Hex, 1/4″-20 x 3/4″, G5, Full Thd
28 495-21031 12 WASHER, 1/4″, flat, 5/16 x 3/4 x 1/16 inch
29 231-1444 6 NUT, LOCK, 1/4″-20, GB
30 1289322C1 1 HOUSING, COVER – hood, to cab transition, right-hand
30 1289321C1 1 HOUSING, COVER – hood, to cab transition, left-hand, not shown
32 229466A3 1 PANEL, decal, left-hand, not shown
32 229465A3 1 PANEL, decal, right-hand
33 495-21038 16 WASHER, 5/16″, flat, 3/8 x 7/8 x 3/32 inch
34 131-205 16 NUT, LOCK, 5/16″-18, heavy hex, self-locking, 5/16 inch NC
36 137886A1 2 SEAL, foam, adhesive back, 19 (3/4) x 19 (3/4) x 80 mm (3-5/32 inch) long, hood to radiator corner
37 141857A1 1 SEAL, SPECIAL MAT, foam, adhesive back, 120 (4-3/4) x 19 (3/4) x 1168 mm (46 inch) long, hood to
39 493-11026 10 WASHER, LOCK, Ext-Int Tooth, 1/4″, internal-external tooth lock, 1/4 inch
40 249781A1 1 GRILLE, SCREEN – front, Magnum, replaces 239356A1 screen
9 413-420 2 BOLT, Hex, 1/4″-20 x 1 1/4″, G5
1 128014A1 1 PANEL ASSY., hood, screen, lower right side, includes item 36, 1348479C1 strip
3 122967A1 1 SUPPORT, side panel, right-hand
4 1960793C5 1 PROTECTION PLATE, SCREEN – hood, side, right-hand
7 131-1418 4 NUT, LOCK, 1/4″-20, Thin, light hex, self-locking, 1/4 inch NC, right-hand side screen to lower
10 1960849C1 2 BRACKET, screen latch outer
11 614-6016 2 BOLT, Hex, M6 x 16, 8.8
12 825-2406 2 NUT, M6 x 1, Flg, Cl 8
14 463-61010 2 SCREW, Hex Hd, #10-32 x 5/8″, machine, hex head, No. 10 NF x 5/8 inch
18 252764A1 2 SEAL, lower side panels, top, 15-3/16 inch (386 mm) long, cut from 252768A1 bulk seal
19 195934A1 1 PANEL ASSY., screen, hood, front low, includes item 36 strip
20 1289399C3 1 PANEL ASSY., hood, left-hand rear lower side
21 122969A1 1 SUPPORT, side panel, left-hand
22 194873A1 1 HINGE, side panel, front, left-hand
23 192284A1 1 HINGE, side panel, rear, left-hand
24 1968038C3 1 SUPPORT ASSY., latch outer
25 1960792C5 1 PROTECTION PLATE, SCREEN – hood side, left
26 463-61010 2 SCREW, Hex Hd, #10-32 x 5/8″, machine, hex head, No. 10 NF x 5/8 inch
27 1960763C3 2 FASTENER, RECEIVER – rear side panel, stud, left-hand
28 260-5448 4 SCREW, SELF TAPPING, Cross Pan Hd, #8 x 1/2″, Phillips
29 495-21019 4 WASHER, #8
30 A149863 1 GUIDE, left-hand rear side panel
31 492-11025 1 WASHER, LOCK, 1/4″
32 425-104 1 NUT, 1/4″-20, G5
35 1348465C1 2 STUD, rear side panel latch
36 1348479C1 2 FOAM, STRIP – wear, 517 mm (20-3/8 inch) long, not shown, cut from 1348532C1X bulk strip
1 1968100C3 4 LINK DRAG, ASSEMBLY – hood tilt, without snap ring groove
1 275185A1 4 LINK DRAG, ASSEMBLY – hood tilt, with snap ring groove, Includes: Ref. 2
2 A59809 2 BUSHING, hood tilt link
3 229428A1 1 SUPPORT, BRACKET – hinge support, right-hand
4 229429A1 1 SUPPORT, BRACKET – hinge support, left-hand
5 131-425 8 NUT, LOCK, Push, 1/2″
8 251154A1 1 LEVER, hood lock
9 100-11100 1 RING, SNAP, #100, Ext, Hood lock lever
10 495-81147 2 WASHER, 13/32″ x 2″ x .109″, flat, 13/32 x 2 x 1/8 inch
11 413-620 1 BOLT, Hex, 3/8″-16 x 1 1/4″, G5, Full Thd
12 131-206 1 NUT, LOCK, 3/8″-16, heavy hex, self-locking, 3/8 inch NC
13 1348231C1 1 HANDLE, GRIP – hood
14 181030A1 1 SUPPORT, BRACE – hood, cylinder
16 495-81286 3 WASHER, .281″ x 1 1/8″ x .060″, flat, 9/32 x 1-1/8 x 1/16 inch
17 231-1444 3 NUT, LOCK, 1/4″-20, GB
20 614-12110 4 BOLT, Hex, M12 x 110, 8.8, Full Thd, BOLT – hex, full threads, 12 – 1.75 x 110 mm
21 829-2312 12 NUT, M12 x 1.75, Flg, Cl 10, hex flange, 12 mm – 1.75, class 10
22 892-11008 2 WASHER, LOCK, M8
23 832-10408 2 NUT, LOCK, M8 x 1.25, Cl 8
25 1968168C3 2 GAS STRUT, CYLINDER ASSEMBLY – hood tilt, Includes: Ref. 26
26 1968120C1 1 SEAL, gas cylinder, no longer a serviced part, order 1968168C3 assembly
27 142597A1 4 STUD, ball
28 3233348R1 4 CLIP, retaining, ball stud
29 892-11010 4 WASHER, LOCK, M10
30 825-1410 4 NUT, M10, Cl 8
31 1289137C1 1 BRACE, hood support, rear
32 413-528 2 BOLT, Hex, 5/16″-18 x 1 3/4″, G5
33 425-105 2 NUT, 5/16″-18, G5
37 A147728 2 TRIGGER, LATCH – hood lock
38 1978450C2 2 SPRING, hood lock
39 231-1444 5 NUT, LOCK, 1/4″-20, GB
40 413-452 2 BOLT, Hex, 1/4″-20 x 3 1/4″, G5, BOLT – hex, 1/4 NC x 3-1/4 inch
42 495-21031 2 WASHER, 1/4″, flat, 5/16 x 3/4 x 1/16 inch
43 495-81286 3 WASHER, .281″ x 1 1/8″ x .060″, flat, 9/32 x 1-1/8 x 1/16 inch
44 1348428C2 1 SEAL, foam, adhesive back, 1042 mm (41 inch) long, lower housing, cut from 252768A1 bulk seal, see
45 235944A4 1 HOUSING, grille, lower
47 231813A2 1 ANGLE, support, grille, right-hand
48 231814A2 1 ANGLE, support, grille, left-hand, not shown
50 814-10060 4 BOLT, Hex, M10 x 60, 8.8
51 892-11010 4 WASHER, LOCK, M10
52 495-81143 8 WASHER, 13/32″ x 1 1/2″ x .120″, flat, 13/32 x 1-1/2 x 7/64 inch
53 825-1410 4 NUT, M10, Cl 8
54 241951A4 1 GRILLE ASSY, SCREEN – grille, lower
55 495-21031 12 WASHER, 1/4″, flat, 5/16 x 3/4 x 1/16 inch
56 231-1444 12 NUT, LOCK, 1/4″-20, GB
15 413-420 3 BOLT, Hex, 1/4″-20 x 1 1/4″, G5
41 413-420 3 BOLT, Hex, 1/4″-20 x 1 1/4″, G5
1 1348227C1 1 COVER ASSY, filter, hydraulic
2 248933A1 1 ANGLE, hydraulic filter cover mounting
3 1975782C1 4 SCREW, SELF TAPPING, Cross Truss Wash Hd, #10 x 5/8″
4 104036C1 4 NUT, expansion, No. 10
5 1348243C1 1 SUPPORT, mounting, filter cover
6 1348244C1 1 SUPPORT, hydraulic filter cover support
8 614-6020 1 BOLT, Hex, M6 x 20, 8.8, Full threads
9 893-11006 3 WASHER, LOCK, Ext Tooth, M6
10 832-10406 3 NUT, LOCK, M6 x 1, Cl 8, Replaces 825-1406 nut
12 1334657C1 1 PLATE, LARGE, cover, models without lower flood lamp
13 1960750C1 3 SCREW, special, 1/4 NC x 3/8 inch
15 626-12035 2 BOLT, Hex, M12 x 35, 10.9, Full Thd, BOLT – hex, full threads, 12 – 1.75 x 35 mm, class 10.9
16 895-11006 4 WASHER, M6
19 614-6025 1 BOLT, Hex, M6 x 25, 8.8, BOLT – hex, full threads, 6 – 1.0 x 25 mm
21 495-81286 1 WASHER, .281″ x 1 1/8″ x .060″, flat, 9/32 x 1-1/8 x 1/16 inch, hardened
23 628-12020 2 BOLT, Hex, M12 x 20, 10.9, Full Thd, BOLT – hex, full threads, 12 – 1.75 x 20 mm, class 10.9
24 896-11012 4 WASHER, M13.5 x 24.5 x 3, HT
25 829-1412 1 NUT, M12, Cl 10
1 1340591C1 2 BRACKET, fender mounting, front
2 495-11066 8 WASHER, 5/8″, SAE, flat, 21/32 x 1-5/16 x 3/32 inch, if used, front fender
2 896-11016 8 WASHER, M17.5 x 30 x 4, HT, If used, Front fender
3 413-1048 8 BOLT, Hex, 5/8″-11 x 3″, G5, hex, 5/8 NC x 3 inch, if used, front fender
3 828-16070 8 BOLT, Hex, M16 x 70, 10.9, If used, front fender
4 814-16110 4 BOLT, Hex, M16 x 110, 8.8, Front fender
5 1340558C1 4 SPACER, fender brace, front
6 1340675C1 1 SUPPORT, BRACE – fender support, right-hand, front
6 1340676C1 1 SUPPORT, BRACE – fender support, left-hand, not shown, front
7 896-11016 4 WASHER, M17.5 x 30 x 4, HT, Front fender
8 832-10416 4 NUT, LOCK, M16 x 2, Cl 8, Front fender
11 1340671C1 2 SUPPORT, fender, inner, front
12 495-21056 4 WASHER, 1/2″, flat, 9/16 x 1-3/8 x 7/64 inch, front fender
13 80679 4 WASHER, LOCK, 1/2″, Front fender
14 425-108 4 NUT, 1/2″-13, G5, Front fender
16 1340664C1 2 FENDER, front wheel, MFD tractor, front fender
17 1340559C2 8 WASHER, square hole, 2-1/2 inch, front fender
20 1340640C1 8 BOLT, carriage, 5/16 NC x 1-1/4 inch, front fender
20 612-6 8 BOLT, CARRIAGE, Short NK, M8 x 30, Cl4.6, Full Thd, If used, front fender
21 495-21038 8 WASHER, 5/16″, flat, 3/8 x 7/8 x 3/32 inch, if used, front fender
22 425-105 8 NUT, 5/16″-18, G5, If used, front fender
22 825-2408 8 NUT, M8 x 1.25, Flg, Cl 8, If used, front fender
23 122212A1 2 FENDER, front wheel, MFD tractor with wide tires 18.4 – 26R2 or 18.4 – 28R1, wide front fenders
24 1340640C1 12 BOLT, carriage, 5/16 NC x 1-1/4 inch, if used, wide front fender, MFD tractor
24 612-6 12 BOLT, CARRIAGE, Short NK, M8 x 30, Cl4.6, Full Thd, If used, wide front fender, MFD tractor
25 1340559C2 12 WASHER, square hole, 2-1/2 inch, wide front fender, MFD tractor
26 495-21038 12 WASHER, 5/16″, flat, 3/8 x 7/8 x 3/32 inch, if used, wide front fender, MFD tractor
27 425-105 12 NUT, 5/16″-18, G5, If used, wide front fender, MFD tractor
27 825-2408 12 NUT, M8 x 1.25, Flg, Cl 8, If used, wide front fender, MFD tractor
28 136309A1 2 SUPPORT, fender, inner, wide, not shown, front, MFD tractor
1 96925C3 1 SUPPORT, instrument panel
2 1974661C1 2 ANGLE, BRACKET – mounting
3 1977582C2 1 HOUSING, upper instrument
4 1270762C1 2 SCREW, SELF TAPPING, pan head Phillips, self-tapping, No. 10-16 x 3/4 inch, mounts cover to
5 104035C1 3 FASTENER, NUT – spacer, No. 10 – 16
7 96696C1 1 SUPPORT ASSY., return spring
9 892-11008 1 WASHER, LOCK, M8
14 96931C2 1 BRACKET, brake pedal stop
15 614-10025 2 BOLT, Hex, M10 x 25, 8.8, Full Thd
16 892-11010 1 WASHER, LOCK, M10
18 96738C3 1 COVER ASSY, instrument panel, prior to serial number JJA0090943
18 310651A1 1 COVER ASSY, instrument panel, serial number JJA0090943 and after
19 495-81286 2 WASHER, .281″ x 1 1/8″ x .060″, flat, 9/32 x 1-1/8 x 1/16 inch
20 614-6016 2 BOLT, Hex, M6 x 16, 8.8
26 1343812C1 1 SYMBOLS, EMBLEM – Magnum
27 103957C1 6 NUT, speed, No. 10 – 16
28 104036C1 2 NUT, cover to instrument panel
29 122856A1 1 SUPPORT, BRACKET – switch mounting
30 96739C3 1 COVER ASSY, side, right-hand
31 96740C2 1 COVER ASSY, side, left-hand
32 614-10020 4 BOLT, Hex, M10 x 20, 8.8, Full Thd
33 825-1410 4 NUT, M10, Cl 8
35 614-8016 1 BOLT, Hex, M8 x 16, 8.8, mounting bracket left-hand hole
35 614-8025 1 BOLT, Hex, M8 x 25, 8.8, Mounting bracket RH hole
36 825-1408 1 NUT, M8, Cl 8
37 892-11008 1 WASHER, LOCK, M8, Mounting bracket RH bolt
38 1964796C1 1 BLANK-OFF PLUG, cover, used without horn
39 1990951C1 2 SCREW, Phillips washer, No. 10- 16 x 5/8 inch (GRAY), right-hand instrument panel housing bottom
40 1990952C1 6 SCREW, Phillips washer, No. 10- 16 x 1 inch (Gray), left-hand instrument panel housing side and top
1 1977661C1 1 PAD, upper instrument housing
2 1977660C2 1 PAD, front console
3 1977659C2 1 PAD, front console lower
4 1977663C1 1 PAD, instrument side panel, left
5 1977662C1 1 PAD, instrument side panel, right
6 1977738C1 1 SUPPORT, BRACKET – console cover
7 1977737C1 1 COVER ASSY, console pad lower (Without manual shuttle shift)
8 96900C1 1 NUT, U, #10-16, Panel type
9 1975919C1 8 SCREW, special, No. 10 – 16 x 1 inch, black
10 1977865C1 2 CLIP, christmas tree
11 298566A1 1 COVER, console pad lower (With manual shuttle shift)
1 193925A1 1 COVER ASSY, transmission and hitch control, includes items 1B and 1C, tractors with electronically
2 96730C3 1 DOOR, hitch operation
3 1344244C1 1 TRAY, utility
4 96724C3 1 COVER, remote
5 96899C1 1 BRACKET, cover support
6 1342054C1 2 PLASTIC PLUG, INSERT – black, blanking, without hitch or draft control switched, not shown
10 490-1108 10 SCREW, Cross Pan Hd, #10-32 x 1/2″, machine, pan Phillips, No. 10 NF x 1/2 inch
11 495-31022 10 WASHER, #10
12 97006C1 2 BOLT, BOLT – hex flange, special, 6 – 1 x 20 mm, polyseal
16 97000C1 1 ASH TRAY, receiver
17 97042C1 1 GASKET, ash tray
18 96723C2 1 PANEL ASSY., corner
19 495-11053 2 WASHER, 1/2″, SAE, (17/32″ x 1-1/16″ x 3/32″)
20 1958720C1 2 STUD, panel retaining
22 96956C2 1 BUTTON, KNOB – cover panel retaining
23 1971363C1 1 RETAINER, bolt
24 123399A1 1 PANEL, right-hand side console, includes pad
26 1990565C1 1 PANEL ASSY., operator manual
29 1981941C3 1 PLATE, LARGE, shift selector (Without creeper)(Without manual shuttle shift)
30 1981942C4 1 PLATE, LARGE, shift selector (With creeper)(Without manual shuttle shift)
31 96577C5 1 PANEL, PLATE – shift selector, 2-speed reverse, (Without creeper)
32 97065C6 1 SECTOR, PLATE – shift selector, 2-speed reverse, (With creeper)
33 96578C4 1 ROD, rest, shift selector
34 614-6016 6 BOLT, Hex, M6 x 16, 8.8
35 614-6012 4 BOLT, Hex, M6 x 12, 8.8
36 1974696C1 1 BRACKET, console support
37 495-11034 2 WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch, replaces 895-11008 washer
38 829-1408 1 NUT, M8, Cl 10
40 490-11010 1 SCREW, Cross Pan Hd, #10-32 x 5/8″, machine, pan Phillips, No. 10 NF x 5/8 inch
41 291434A1 1 PLATE, LARGE, shift selector (With and without creeper)(With manual shuttle shift)
1 96886C5 1 LEVER, switch, creeper (Without manual shuttle shift)
2 97063C1 1 WASHER, curved
3 738-1214 1 PIN, LOCK, M2 x 14, Slotted, roll, 2 x 14 mm
4 97062C1 1 CABLE PULLING GRIP, creeper switch
5 96569C7 1 SUPPORT ASSY., shift and governor control
6 96725C1 1 PANEL ASSY., front cover
14 97297C1 1 ROD, tower support
15 825-1406 2 NUT, M6, Cl 8, May be replaced by 825-5146 serrated flange nut, item 15A
17 96890C2 1 BRACKET, creeper switch
18 840-1516 2 SCREW, Cross Pan Hd, M5 x 16
19 895-11005 2 WASHER, M5 x 10 x 1
20 892-11005 2 WASHER, LOCK, M5
21 824-1405 2 NUT, M5, Cl 5
25 614-10035 2 BOLT, Hex, M10 x 35, 8.8, Full Thd
26 825-2406 4 NUT, M6 x 1, Flg, Cl 8
27 96700C2 1 BRACKET, control support
28 614-8025 2 BOLT, Hex, M8 x 25, 8.8
29 495-11034 3 WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch, replaces 895-11008 washer
30 832-41308 2 NUT, M8 x 1.25, Cl 10, hex, self-locking, 8 mm – 1.25, class 10.9
33 1340412C2 1 SUPPORT, BRACKET – shift cable, upper
34 628-8030 2 BOLT, Hex, M8 x 30, 10.9, Full Thd
35 832-41308 2 NUT, M8 x 1.25, Cl 10, hex, self-locking, 8 mm – 1.25, class 10.9
36 1344243C2 1 SUPPORT, shift tower
37 294264A1 1 LEVER, switch, creeper (With manual shuttle shift)
1 134181A2 1 PACKAGE, KIT – seat top, without armrest, cushion and backrest, complete
2 132886A1 1 BACKREST, KIT – cloth, without armrest, with structure
9 1999693C1 1 KIT, CLIP – christmas tree, package of 14, retaining, plastic
10 143199A1 1 ARMREST, right-hand, black, includes armrest and switch cover plug
11 1981818C1 1 ARMREST, KIT – left-hand, black
13 38-31016 2 PIN, 5/32″ x 1″, Coiled
16 30299R1 1 SCREW, Cross Oval Hd, M6 x 12, machine, 6 x 12 mm, special
18 1981829C1 1 STAY, WINDOW, KNOB – fore/aft not shown, see item 11 on Figure 9-44 for knob
19 1343982C1 1 BELT, SAFETY, seat
20 1975957C1 1 BRACKET, seat belt, left-hand
21 328-724 1 BOLT, Hex, 7/16″-20 x 1 1/2″, G8
22 328-732 1 BOLT, Hex, 7/16″-20 x 2″, G8
23 413-544 2 BOLT, Hex, 5/16″-18 x 2 3/4″, G5
24 1343875C1 2 SPACER, 25/64 ID x 1/2 inch
25 395-11053 3 WASHER, 1/2″, flat, 17/32 x 1-1/16 x 3/32 inch
26 232-4117 2 NUT, LOCK, 7/16″-14, GC
27 176091A1 1 PACKAGE,SERVICE, KIT – retaining, hog ring, package of 48 rings for cushions
28 141566A1 1 PLATE, LARGE, reinforcement
1 134180A1 1 PLATE, seat adapter
2 413-524 8 BOLT, Hex, 5/16″-18 x 1 1/2″, G5
3 134144A1 4 SPACER, plate
7 117-109 4 BOLT, Sq Hd, 5/18″-16 x 3/4″, G5, Replaces 417-512 bolt
8 413-512 4 BOLT, Hex, 5/16″-18 x 3/4″, G5, Full Thd
9 495-11034 4 WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch
10 230-4215 8 NUT, LOCK, 5/16″-18, GA, hex, self-locking, 5/16 inch NC
11 1981829C1 1 STAY, WINDOW, KNOB – fore/aft available in 1999691C1 knob kit on Figure 9-42
12 133422A1 2 BUMPER, down stop
14 340-12520 2 SCREW, Cross Pan Hd, 1/4″-20 x 1 1/4″
16 231-1444 2 NUT, LOCK, 1/4″-20, GB
1 241189A1 1 HOUSING, upper, suspension, replaces 1990642C1 housing
2 1990645C1 1 LATCH, ASSEMBLY – isolator, fore and aft, component parts not serviced separately, see Figure 9-50
3 276-24812 2 SCREW, SELF TAPPING, Hex Hd, 5/16″ x 3/4″
4 1990643C1 1 FRAME ASSY, ARM – scissor, suspension
5 A49529 1 SHAFT, bushing tube
6 231-4206 1 NUT, LOCK, 3/8″-16, GB, Hex, self-locking, Replaces 230-4216 nut
7 1981834C1 1 HOUSING, lower, no longer available, order 226560A1 housing below, A45054 bumber and 132872A1
7 226560A1 1 HOUSING, lower, replaces 1981834C1 housing
8 443-13812 1 SCREW, Cross Flat Hd, 3/8″-16 x 3/4″, machine, flat Phillips, 3/8 NC x 3/4 inch
10 413-68 1 BOLT, Hex, 3/8″-16 x 1/2″, G5, Full Thd
11 131-425 1 NUT, LOCK, Push, 1/2″
13 134237A2 1 HARNESS, compressor wire, without operator presence
15 440-1086 2 SCREW, Cross Pan Hd, #8-32 x 3/8″, machine, pan Phillips, No. 8 NC x 3/8 inch
16 495-31022 2 WASHER, #10
17 L18337 2 STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch
18 134456A1 1 HARNESS, wire adapter, with grommet, without operator presence
19 1981849C2 2 SHOCK ABSORBER, BUMPER – rubber, upper housing, not shown, see Figure 9-44, item 15 for
23 A47760 2 BUSHING, TUBE – bearing, shaft
24 1981788C1 2 ROLLER, SHIFTER, suspension
26 1981846C1 1 CAP CYLINDER END, BEARING – spring bar, isolator latch tube, not shown, see Figure 9-50, item 13
33 A45519 1 WASHER, flat, plastic, special, 33/64 x 1-1/8 x 1/16 inch
34 131-425 1 NUT, LOCK, Push, 1/2″
37 434-48 2 BOLT, CARRIAGE, Short NK, 1/4″-20 x 1/2″, G5, Full Thd
38 231-1444 2 NUT, LOCK, 1/4″-20, GB
39 495-11041 2 WASHER, 3/8″, SAE, Flat, (13/32 x 13/16 x 1/16″)
42 230-4715 1 NUT, LOCK, 5/16″-24, GA, Hex
43 A49679 2 BUSHING, rubber
45 1981845C1 1 ANGLE, mounting, shock mounting
48 493-11065 1 WASHER, LOCK, Ext-Int Tooth, 5/8″, internal-external tooth lock, 5/8 inch
49 1987186C2 1 KNOB, KNOB – switch, air suspension
55 L18337 4 STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch
61 A45519 1 WASHER, flat, plastic, special, 33/64 x 1-1/8 x 1/16 inch
63 179026A1 1 TUBE, PLASTIC-RUBBER, SLEEVE – guard, 10 (3/8) ID x 615mm (24-1/4 inch) long
64 L18337 2 STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch
65 340-12520 2 SCREW, Cross Pan Hd, 1/4″-20 x 1 1/4″, Special, not shown, see item 14 on Figure 9-44 for screw
66 179026A1 1 TUBE, PLASTIC-RUBBER, SLEEVE – guard, 10 (3/8) ID x 615 mm (24-1/4 inch) long
67 133422A1 2 BUMPER, down stop, not shown, see item 12 on Figure 9-44 for bumper
68 241210A1 1 HARNESS, wire, with operator presence
69 241206A1 1 HARNESS, wire, with grommet, with operator presence
19 495-11034 4 WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch
20 614-8020 4 BOLT, Hex, M8 x 20, 8.8
21 1977735C1 2 SUPPORT, BRACKET – mounting, seat
22 1954650C1 4 STUD, 8 x 80 mm
23 F15988 4 SPACER, seat mounting
24 892-11008 4 WASHER, LOCK, M8
25 829-1408 4 NUT, M8, Cl 10
1 134181A2 1 PACKAGE, KIT – seat top, without armrest, includes seat cushion and backrest, complete
2 132886A1 1 BACKREST, KIT – cloth, without armrest, with structure
9 1999693C1 1 KIT, CLIP – christmas tree, package of 14, retaining, plastic
11 143199A1 1 ARMREST, right-hand, black, tilt, includes switch cover plug
12 132882A1 1 ARMREST, left-hand, pad, black
13 132883A2 1 PACKAGE, KIT – left-hand armrest adjustment, repair kit, includes thumb wheel, cable, hub latch, latch
14 413-528 1 BOLT, Hex, 5/16″-18 x 1 3/4″, G5
15 495-11034 1 WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch
16 413-544 2 BOLT, Hex, 5/16″-18 x 2 3/4″, G5
17 1343875C1 2 SPACER, 25/64 ID x 1/2 inch
19 38-31016 2 PIN, 5/32″ x 1″, Coiled
20 1974711C1 1 LEVER, KNOB – backrest tilt
22 30299R1 1 SCREW, Cross Oval Hd, M6 x 12, machine, 6 x 12 mm, special
25 1343982C1 1 BELT, SAFETY, seat
26 1975957C1 1 BRACKET, seat belt, left-hand
27 328-724 1 BOLT, Hex, 7/16″-20 x 1 1/2″, G8
28 328-732 1 BOLT, Hex, 7/16″-20 x 2″, G8
29 413-544 2 BOLT, Hex, 5/16″-18 x 2 3/4″, G5
30 1343875C1 1 SPACER, 25/64 ID x 1/2 inch
31 395-11053 2 WASHER, 1/2″, flat, 17/32 x 1-1/16 x 3/32 inch
32 232-4117 2 NUT, LOCK, 7/16″-14, GC
33 132868A1 1 SET OF PARTS, KIT – height adjustment, includes (3) cover plate, (1) rocker switch, and (4) screws
34 141566A1 1 PLATE, LARGE, reinforcement, seat frame to backrest frame, left-hand
35 176091A1 1 PACKAGE,SERVICE, KIT – retaining, hog ring, package of 48 rings for cushions
1 134148A1 1 SUPPORT, SEAT, PLATE – swivel, complete, Includes: Ref. 2, 3, 4
2 135511A1 1 ROD, ADJUSTMENT, swivel, includes knob
3 A47375 1 SPRING, detent
5 132878A3 1 ISOLATOR, PLATE – lateral, complete, Includes: Ref. 6-25, and Kits
8 253593A1 2 BEARING, isolator rod, isolator rod
9 135510A2 1 ROD, ADJUSTMENT, isolator, includes knob
10 38-31012 2 PIN, 5/32″ x 3/4″, Coiled, 5/32″ x 3/4″, Coiled
11 1344026C1 1 SPRING, latch
13 495-11041 2 WASHER, 3/8″, SAE, Flat, (13/32 x 13/16 x 1/16″)
15 230-4715 1 NUT, LOCK, 5/16″-24, GA, Hex
13 495-11041 2 WASHER, 3/8″, SAE, Flat, (13/32 x 13/16 x 1/16″)
14 A49679 2 BUSHING, rubber
15 230-4715 1 NUT, LOCK, 5/16″-24, GA, Hex
18 1344025C1 1 PIN, LARGE, clevis, shock mount
19 100-3350 1 RING, LOCKING, #50, .392″ Dia, E-Type
20 433-512 4 BOLT, CARRIAGE, Short NK, 5/16″-18 x 3/4″, G5, 5/16 NC x 3/4 inch
21 230-4215 4 NUT, LOCK, 5/16″-18, GA, hex, self-locking, 5/16 inch NC
23 413-816 1 BOLT, Hex, 1/2″-13 x 1″, G5, Full Thd
28 180587A1 1 HANDLE, KNOB – slide control, fore/aft
30 103-1412 2 RING, SNAP, #12, Ext
32 100-3331 2 RING, LOCKING, #X31, .243″ Dia, E-Type
35 L18337 3 STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch
37 231-1444 12 NUT, LOCK, 1/4″-20, GB
38 103-1412 2 RING, SNAP, #12, Ext
39 100-3331 2 RING, LOCKING, #X31, .243″ Dia, E-Type
42 L18337 3 STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch
44 100-3331 2 RING, LOCKING, #X31, .243″ Dia, E-Type
45 413-532 4 BOLT, Hex, 5/16″-18 x 2″, G5
46 187006A1 2 CUP, SPACER – 3/8 inch bolt size
47 700711545 2 CUP, SPACER – 5/8 inch bolt size
48 413-510 4 BOLT, Hex, 5/16″-18 x 5/8″, G5, Full Thd
49 495-11034 2 WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch
50 231-4115 4 NUT, LOCK, 5/16″-18, GB
51 135513A1 1 SPRING, torsion
52 135514A1 1 SPRING, torsion
55 100-3325 2 RING, LOCKING, #25, .207″ Dia, E-Type
56 131-413 2 NUT, LOCK, Rd Flat Push, 1/4″ x 17/32″, push-on type, 1/4 x 17/32 inch
57 134146A1 1 LEVER, CONTROL, slide
58 134144A1 4 SPACER, plate
61 117-109 4 BOLT, Sq Hd, 5/18″-16 x 3/4″, G5
62 413-520 4 BOLT, Hex, 5/16″-18 x 1 1/4″, G5
63 230-4215 8 NUT, LOCK, 5/16″-18, GA, hex, self-locking, 5/16 inch NC
1 241189A1 1 HOUSING, upper, suspension, replaces 1990642C1 housing
2 132862A1 1 DIPPER, ARM – suspension
3 A49529 1 SHAFT, bushing tube
4 230-4216 1 NUT, LOCK, 3/8″-16, GA
5 226560A1 1 HOUSING, lower
6 443-13812 1 SCREW, Cross Flat Hd, 3/8″-16 x 3/4″, machine, flat Phillips, 3/8 NC x 3/4 inch
8 413-68 1 BOLT, Hex, 3/8″-16 x 1/2″, G5, Full Thd
9 131-425 1 NUT, LOCK, Push, 1/2″
13 495-11041 2 WASHER, 3/8″, SAE, Flat, (13/32 x 13/16 x 1/16″)
14 132867A1 1 HARNESS, wire
15 A47760 2 BUSHING, TUBE – bearing, shaft
26 131-425 2 NUT, LOCK, Push, 1/2″
28 138-317 1 PIN, LOCK, 1/8″ x 5/8″, Slotted
30 144514A1 2 SUPPORT, BRACKET – cable control, shock
34 434-48 2 BOLT, CARRIAGE, Short NK, 1/4″-20 x 1/2″, G5, Full Thd
35 231-1444 2 NUT, LOCK, 1/4″-20, GB
36 495-11041 2 WASHER, 3/8″, SAE, Flat, (13/32 x 13/16 x 1/16″)
39 230-4715 1 NUT, LOCK, 5/16″-24, GA, Hex
40 A49679 2 BUSHING, rubber
42 1981845C1 1 ANGLE, mounting, shock mounting
45 L18337 2 STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch
47 179026A1 1 TUBE, PLASTIC-RUBBER, SLEEVE – guard, 10 (3/8) ID x 615 mm (24-1/4 inch) long
48 L18337 3 STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch
49 230-4715 1 NUT, LOCK, 5/16″-24, GA, Hex
5 276-24812 2 SCREW, SELF TAPPING, Hex Hd, 5/16″ x 3/4″
6 132863A1 1 ISOLATOR, LATCH – fore and aft, component parts not serviced separately, Includes: Screw, Shaft
8 133422A1 2 BUMPER, down stop
9 340-12520 2 SCREW, Cross Pan Hd, 1/4″-20 x 1 1/4″
11 231-1444 2 NUT, LOCK, 1/4″-20, GB
12 144847A1 2 RISER, BRACKET – mounting, seat, 83 mm (3-1/4 inch high) high riser, prior to seat serial number
12 222771A1 2 RISER, BRACKET – mounting, seat, 98 mm (3-7/8 inch) high riser, effective seat serial number
13 495-11034 4 WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch
14 614-8020 4 BOLT, Hex, M8 x 20, 8.8
15 1954650C1 4 STUD, 8 x 80 mm
16 F15988 4 SPACER, seat mounting
17 892-11008 4 WASHER, LOCK, M8
18 829-1408 4 NUT, M8, Cl 10
20 190156A1 1 SHOCK ABSORBER, KIT – block, sheave, Includes: Block, Spring, Shoe
21 132868A1 1 SET OF PARTS, KIT – height adjustment, not shown, see Figure 9-52, item 33
1 96523C2 2 BRACKET, mounting, front
2 628-20050 8 BOLT, Hex, M20 x 50, 10.9, Full Thd, Front
3 892-11020 8 WASHER, LOCK, M20, 20 mm, front
4 1286902C1 1 INSULATOR, MOUNT – isolation, top, front
5 1286903C1 1 INSULATOR BLOCK, MOUNT – isolation, bottom, front
6 1982005C1 4 SPACER, rebound, front
7 1982004C1 4 SCREW, BOLT – special, front
8 R52105 2 WASHER, flat, 13/16 x 1-3/4 x 7/32 inch, front
9 117737C1 2 PLATE, mounting, front
10 495-21081 2 WASHER, 3/4″, flat, 13/16 x 2 x 9/64 inch, front
11 425-1012 2 NUT, 3/4″-10, G5, Front
12 1982052C2 1 SUPPORT, BRACKET – mounting, left-hand rear
13 1982053C2 1 SUPPORT, BRACKET – mounting, right-hand rear
14 828-16150 4 BOLT, Hex, M16 x 150, 10.9, Rear
15 628-16045 4 BOLT, Hex, M16 x 45, 10.9, Full Thd, Rear
16 892-11016 8 WASHER, LOCK, M16, Rear
17 144212C1 8 WASHER, flat, rear
18 1286902C1 1 INSULATOR, MOUNT – isolation top, rear
19 1286903C1 1 INSULATOR BLOCK, MOUNT – isolation, bottom, rear
20 1982005C1 8 SPACER, rear mounting spacer
21 1982004C1 4 SCREW, BOLT – special, rear
22 253322A1 2 PLATE, mounting, rear
23 R52105 2 WASHER, flat, 13/16 x 1-3/4 x 7/32 inch, rear
24 425-1012 2 NUT, 3/4″-10, G5, Rear
1 96639C1 1 SUPPORT ASSY., step
2 97049C3 1 STEP, tractor, top
3 97050C3 2 STEP, ladder, intermediate and lower
4 1348398C1 12 BOLT, BOLT – hex, 10 x 35 mm, grade 8.8
5 1348399C1 14 NUT, hex serrated flange, 10 – 1.5 mm
1 236996A3 1 FRAME, ASSEMBLY – cab, not shown
3 96964C1 1 PLATE ASSY., floor access
4 1971260C1 2 SEAL ASSY., floor access plate
5 281-34812 10 SCREW, SELF TAPPING, Hex Hd, 5/16″ x 3/4″, self-tapping, hex washer head, 5/16 NC x 3/4 inch
6 284854A1 1 PLATE ASSY., implement cable, cover foot throttle opening
7 281-14512 2 SCREW, SELF TAPPING, Hex Wash Hd, #10 x 3/4″, self-tapping, hex washer head, No. 10 NC x 3/4
8 A165354 1 SEAL, plate
12 A177462 1 MIRROR, rear view, includes mounting hardware
13 1330064C1 3 NUT, hex flange, self-locking, polyseal, 5/16 inch NC
14 96845C1 1 BRACKET, mirror
15 1330156C1 2 BOLT, self-locking, hex flange, special, 5/16 NC x 3/4 inch
19 97028C1 1 PLUG, post, right
23 1334281C3 1 INSULATOR, PAD – insulation, firewall, front
24 1334282C2 1 INSULATOR, PAD – insulation, upper
25 1334283C2 1 INSULATOR, PAD – insulation, firewall, left
26 1334284C2 1 INSULATOR, PAD – insulation, firewall, right
27 97027C1 1 PAD, firewall
28 91963C1 1 STRAP, GROUND
29 892-11010 1 WASHER, LOCK, M10
30 829-2410 1 NUT, M10 x 1.5, Flg, Cl 10
33 251205A1 1 HANDLE, rear, models without remote hitch switch, see Figure 8-28, item 13 for handle on models with
34 434-516 2 BOLT, CARRIAGE, Short NK, 5/16″-18 x 1″, G5, Full Thd
35 495-11034 4 WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch
36 492-11031 4 WASHER, LOCK, 5/16″
37 425-105 4 NUT, 5/16″-18, G5
38 136893A1 1 SWITCH, dome lamp, with straight male blade terminals, if used
40 96720C2 1 COVER ASSY, front cab post, left side lower
41 1344112C1 2 SCREW, Phillips, self-tapping, polyseal (Black)
41 1990953C1 2 SCREW, Phillips washer, No. 10-24 x 1 inch (Gray)
45 97010C1 2 BOLT, SPREADER, hex flange, 6 – 1.0 x 12 mm
46 353-411 2 PLUG, Dome, 1.000″ hole, Nylon
47 231-5145 1 NUT, Flg, USR, 5/16″-18, Used with interior mirror
1 97003C2 1 FENDER, tractor, left-hand
2 434-516 4 BOLT, CARRIAGE, Short NK, 5/16″-18 x 1″, G5, Full Thd
3 1990666C1 1 SUPPORT, fuel filler tube
6 1990669C1 1 SUPPORT, fender, lower left-hand
7 1990668C1 1 SUPPORT, fender, center left-hand
8 1990667C1 1 SUPPORT, fender, upper left-hand
10 477-73112 4 BOLT, Slotted Tr Hd, 5/16″-18 x 3/4″, BOLT – serrated slotted truss head, 5/16 NC x 3/4 inch, mounting
11 198983A1 4 WASHER, flat, 11/32 x 1-1/8 x 1/16 inch thick, used with item 10 screw
15 1283847C1 1 SUPPORT, BRACKET – rear
16 495-21038 2 WASHER, 5/16″, flat, 3/8 x 7/8 x 3/32 inch
17 237040A1 1 PANEL, COVER – post, upper left
18 495-31016 1 WASHER, #6, Used with item 22 screw on upper post cover, if used
19 1270762C1 2 SCREW, SELF TAPPING, pan head Phillips, self-tapping, No. 10-16 x 3/4 inch, panel
20 96709C1 1 COVER ASSY, post, lower, left
22 140670A1 2 SCREW, hex washer, No. 8 x 3/4 inch, if used, may be replaced by 220408A1 screw with washer, item
23 495-31016 2 WASHER, #6, If used
25 96764C2 1 PANEL ASSY., frame, lower left front
28 96763C1 1 PANEL ASSY., step
29 1971318C1 1 STEP, THRESHOLD – entrance, tractor
30 1971367C2 2 SCREW, SELF TAPPING, Cross Oval Hd, #10-16 x 3/4″, self-tapping, oval head Phillips, No. 10-16 x
31 96930C1 1 PLATE, PANEL – tail lamp
33 253419A1 2 SCREW, Hex Wash Hd, #8-18 x 5/8″, hex washer, No. 8 – 18 x 5/8 inch, special, replaces 220408A1
1 97004C2 1 FENDER, right, tractor
2 1283847C1 1 SUPPORT, BRACKET – rear
3 434-516 4 BOLT, CARRIAGE, Short NK, 5/16″-18 x 1″, G5, Full Thd
4 495-21038 2 WASHER, 5/16″, flat, 3/8 x 7/8 x 3/32 inch
5 231-5145 6 NUT, Flg, USR, 5/16″-18
6 1990670C1 1 SUPPORT, fender, lower right-hand
7 1990671C1 1 SUPPORT, fender, upper right-hand
8 1990672C1 1 SUPPORT, fender, front right-hand
14 96702C2 1 PANEL ASSY., side, right
17 1348226C1 1 PANEL ASSY., frame, lower front right-hand
18 96710C1 1 COVER ASSY, post, lower right-hand
19 237041A1 1 COVER, upper right-hand
22 1975782C1 2 SCREW, SELF TAPPING, Cross Truss Wash Hd, #10 x 5/8″
23 495-31016 1 WASHER, #6, Used with item 25, if used
25 140670A1 1 SCREW, hex washer, No. 8 x 3/4 inch, hi-lo, if used, may be replaced by 253419A1 screw with washer
26 253419A1 1 SCREW, Hex Wash Hd, #8-18 x 5/8″, hex washer, No. 8 – 18 x 5/8 inch, special, replaces 220408A1
27 104033C2 2 SCREW, SELF TAPPING, Cross Wash Hd, M4.8 x 19, Coated, self-tapping, truss head, No. 10-16 x
1 96755C6 1 ROOF, cab
2 98355C1 1 INSULATION, FOAM, SEAL – roof, 810 mm (31-7/8 inch) long
3 98356C1 1 SEAL ASSY., 5100 mm (200-7/8 inch), cut from 1974883CX bulk seal, see below
4 98358C1 2 STRIP, SEAL – 210 mm (8-17/64 inch) long, cut from 1974883CX bulk seal, see below
5 98359C1 1 STRIP, SEAL – 100 mm (3-16/16 inch) long, cut from 1974883CX bulk seal, see below
9 96814C3 8 WASHER, flat, special, sector arm
13 1330157C1 8 NUT, self-locking, hex flange, special, 1/4 inch NC
14 240869A1 1 COVER ASSY, support
22 240871A1 2 HINGE, cover, support
23 413-416 4 BOLT, Hex, 1/4″-20 x 1″, G5
24 231-1444 10 NUT, LOCK, 1/4″-20, GB
27 417-440 2 BOLT, Sq Hd, 1/4″-20 x 2 1/2″, G2, BOLT – square head, 1/4 NC x 2-1/2 inch, grade 2
28 1971364C1 2 RETAINER, bolt
29 1340216C1 4 BUTTON, KNOB – retaining, cover
30 195-81032 14 WASHER, .266″ x 13/16″ x .083″, flat, 17/64 x 13/16 x 3/32 inch
31 1340093C2 4 PLATE, LARGE, STRAP – knob retaining
33 1975760C2 1 COVER, wiper arm
34 414-410 2 BOLT, Hex, 1/4″-28 x 5/8″, G5, Full Thd, BOLT – hex, 1/4 NF x 5/8 inch, polyseal
35 1977988C1 4 FOAM, PAD – foam, anti-bird, 76 (3) x 76 (3) x 280 mm (11 inch) long
35 258941A1 2 FOAM, PAD – filler, anti-bird, 76 (3) x 76 (3) x 140 mm (5-1/2 inch) long
1 1343890C1 1 DOOR, FRAME – cab
2 1977941C2 1 LATCH ASSY., door, rotary
3 413-412 3 BOLT, Hex, 1/4″-20 x 3/4″, G5, Full Thd
4 493-81002 3 WASHER, LOCK, Ext-Int Tooth, 1/4″, internal-external tooth lock, 1/4 inch
5 A177435 1 KNOB,BALL, lever
8 97112C3 1 ARM, latch, door
9 439-148 3 PIN, HEADED, 1/4″ x 1/2″, headed, 1/4 x 1/2 inch, grade 2, mounting, arm
13 1974835C1 1 TUBE, HOSE – spring damper
14 97057C2 1 SPRING, TENSION, handle
16 97218C1 1 BRACKET, mounting, spring
17 413-48 1 BOLT, Hex, 1/4″-20 x 1/2″, G5, Full Thd, hex, 1/4 NC x 1/2 inch
18 425-104 1 NUT, 1/4″-20, G5
20 432-88 3 PIN, SPLIT (COTTER), 1/8″ x 1/2″
21 1340019C3 1 CABLE, door
22 1340149C2 1 HANDLE, door, outer
25 409-748 3 BOLT, Hex Flg, 1/4″-20 x 1/2″, Serr
26 1987149C1 1 HANDLE, grab, door
27 1330156C1 2 BOLT, self-locking, hex flange, special, 5/16 NC x 3/4 inch
28 195-81005 2 WASHER, 3/8″ x 7/8″ x .083″, flat, 3/8 x 7/8 x 5/64 inch
29 1990761C2 1 SEAL, DOOR, 4483 mm (176-1/2 inch) long, door
30 1974873C1 1 WASHER, GASKET – handle, door, large
31 1974872C1 1 WASHER, GASKET – handle, door, small
33 96840C1 1 HANDLE, grab
34 1283589C2 2 WASHER, PAD – mounting, handle
35 1330156C1 2 BOLT, self-locking, hex flange, special, 5/16 NC x 3/4 inch
36 1283690C1 1 ROD, guard, handle
37 409-748 2 BOLT, Hex Flg, 1/4″-20 x 1/2″, Serr
40 97082C6 1 PANEL ASSY., door
41 104033C2 2 SCREW, SELF TAPPING, Cross Wash Hd, M4.8 x 19, Coated, self-tapping, truss head, No. 10-16 x
41 1990951C1 2 SCREW, Phillips washer, No. 10-16 x 5/8 inch (Gray)
42 96736C2 1 PANEL ASSY., trim, door
43 97207C1 3 SCREW, self-tapping, No. 10-24 x 3/4 inch (Black)
43 1990953C1 3 SCREW, Phillips washer, No. 10-24 x 1 inch (Gray)
47 118071C2 1 SCREW, pan Phillips, self-tapping, No. 8 NC x 1/2 inch
48 495-21019 1 WASHER, #8
49 1283695C1 1 STIFFENER, REINFORCEMENT – door handle
50 1977459C1 3 INSULATOR, SHEET – vibration dampening, 100 x 254 mm
51 1977658C1 1 LINING, PAD – door, upper
52 1977657C1 1 LINING, PAD – door, lower
53 179093 1 BUTTON, HOLE PLUG, 9/32″, 9/32 inch ID
54 1975713C1 4 FASTENER, velcro, 1-1/2 x 1 inch, if used, not shown
1 1343890C2 1 DOOR, FRAME – cab, see Figure 9-78, item 40 for panel, REF 1, 9, 12 thru 15, 19 and 27, plus one
2 1280263C1 1 CYLINDER ASSY., door
3 3233348R1 2 CLIP, retaining
4 3234063R1 2 BALL JOINT, STUD – 1-9/32 inch long, if used
4 142597A1 2 STUD, ball, 1-17/32 inch long, if used
5 829-2410 1 NUT, M10 x 1.5, Flg, Cl 10
9 96627C2 1 HINGE, door, upper, REF 1, 9, 12 thru 15, 19 and 27, plus one each of items 3 and 4 above are
10 121-116 2 BOLT, Hex Flg, 5/16″-18 x 1″, Serr
11 195-81005 2 WASHER, 3/8″ x 7/8″ x .083″, flat, 3/8 x 7/8 x 5/64 inch
12 231800A1 4 BUSHING, hinge, REF 1, 9, 12 thru 15, 19 and 27, plus one each of items 3 and 4 above are included
13 231-4115 2 NUT, LOCK, 5/16″-18, GB, , REF 1, 9, 12 thru 15, 19 and 27, plus one each of items 3 and 4 above
14 495-11034 2 WASHER, 5/16″, SAE, flat, 11/32 x 11/16 x 1/16 inch, REF 1, 9, 12 thru 15, 19 and 27, plus one each
15 413-548 2 BOLT, Hex, 5/16″-18 x 3″, G5, BOLT – hex, 5/16 NC x 3 inch, REF 1, 9, 12 thru 15, 19 and 27, plus
19 96623C2 1 HINGE, door, lower, REF 1, 9, 12 thru 15, 19 and 27, plus one each of items 3 and 4 above are
20 121-116 3 BOLT, Hex Flg, 5/16″-18 x 1″, Serr
21 195-81005 3 WASHER, 3/8″ x 7/8″ x .083″, flat, 3/8 x 7/8 x 5/64 inch
23 1283245C3 1 PLATE ASSY., striker
24 1283244C1 1 PLATE ASSY., tapping
26 409-7516 2 BOLT, Hex Flg, 5/16″-18 x 1″, Serr
27 396-31041 1 WASHER, 13/32″ x 13/16″ x .134″, HDN, , REF 1, 9, 12 thru 15, 19 and 27, plus one each of items 3
1 240875A1 1 GLASS, window, rear
2 240876A1 1 SEAL, glass, window
3 F66089 1 PLUG, 3/8 inch diameter, window
4 F66090 1 PLUG, 29/32 inch diameter, window
6 K303501 2 SPACER, rubber
7 K303571 2 WASHER, flat, 6 mm
10 K303517 2 PIN, LARGE, hinge
11 800-418 2 RING, SNAP, M8, Ext, external retaining, No. 8
12 1999808C1 2 HINGE, window
13 107135A1 2 SCREW, BOLT – hex flange
14 97005C1 2 NUT, hex flange, self-locking, special, 6 mm – 1
19 1330064C1 2 NUT, hex flange, self-locking, polyseal, 5/16 inch NC
20 138739A1 2 SUPPORT, BRACKET – cylinder
21 109587C2 2 PAD, bracket
22 109171C1 4 BUSHING, bolt
25 97005C1 4 NUT, hex flange, self-locking, special, 6 mm – 1
26 97006C1 4 BOLT, BOLT – hex flange, special, 6 – 1 x 20 mm
27 1343825C1 2 SHOCK ABSORBER, CYLINDER – gas spring
28 1999766C1 2 BALL JOINT, STUD –
36 1340208C1 2 PAD, RUBBER, PAD – rubber
37 1340203C1 1 PLATE, clamping
38 97011C1 2 SCREW, BOLT – hex flange, special
39 97005C1 2 NUT, hex flange, self-locking, special, 6 mm – 1
42 1340142C1 1 PLATE, striker
43 261-34720 2 SCREW, SELF TAPPING, Cross Pan Hd, 1/4″ x 1 1/4″, self-tapping, pan head Phillips, 1/4 NC x 1-1/4
44 97017C1 2 INSERT, threaded, 6 mm, if used
46 1340207C1 1 PLUG, window hinge
47 1340205C1 1 HANDLE, rear window, no longer available, to service order items 53, 54, 55, and 59 below
48 614-6020 1 BOLT, Hex, M6 x 20, 8.8, Full threads
49 1340206C1 1 BUSHING, LARGE, rubber
50 895-11012 1 WASHER, M12 x 24 x 2.5, flat, 13.5 x 24 x 2.5 mm
51 38-21010 1 PIN, 5/32″ x 5/8″, Coiled, 5/32″ x 5/8″, Coiled
52 194322A1 1 PLATE, clamping
54 224731A1 1 HANDLE, rear window
55 825-1408 1 NUT, M8, Cl 8
56 1340206C1 1 BUSHING, LARGE, rubber
57 895-11012 1 WASHER, M12 x 24 x 2.5, flat, 13.5 x 24 x 2.5 mm
58 38-21010 1 PIN, 5/32″ x 5/8″, Coiled, 5/32″ x 5/8″, Coiled
59 224732A1 1 PLATE ASSY., clamping
1 129-500 2 NUT, WING, #10-32, wing, No. 10 NC, rear access kit
2 A165352 1 PLATE, cable access, rear kit
3 A165354 2 SEAL, cable access, rear kit
4 A165523 2 FASTENER, RETAINER – special, rear access kit
5 440-11012 2 SCREW, Cross Pan Hd, #10-24 x 3/4″, machine, pan Phillips, No. 10 NC x 3/4 inch, rear access kit
10 97133C1 1 VISOR, SUN, kit, sunvisor
11 1971367C2 2 SCREW, SELF TAPPING, Cross Oval Hd, #10-16 x 3/4″, self-tapping, oval head Phillips, No. 10-16 x
1 96671C3 1 GLASS, window, right side
2 1987247C2 1 SEAL, window
4 K303517 2 PIN, LARGE, hinge
5 800-418 2 RING, SNAP, M8, Ext, external retaining, No. 8
6 K303501 4 SPACER, rubber
7 K303571 2 WASHER, flat, 6 mm
10 1999808C1 2 HINGE, window
11 107135A1 2 SCREW, BOLT – hex flange
12 97005C1 2 NUT, hex flange, self-locking, special, 6 mm – 1
13 1954284C1 2 BRACKET, cylinder, sector
14 97006C1 4 BOLT, BOLT – hex flange, special, 6 – 1 x 20 mm
15 97005C1 4 NUT, hex flange, self-locking, special, 6 mm – 1
16 109171C1 4 BUSHING, bolt
18 109587C2 2 PAD, bracket
19 1954283C1 2 BOLT, SPREADER, hex shoulder, 6 x 25 mm
20 1954279C1 10 WASHER, flat, 7 x 16 x 2 mm
21 96849C2 6 WASHER, spring, curved
22 96814C3 8 WASHER, flat, special, sector
23 427-5071 2 PIN, CLEVIS, 5/16″ x .719″, 5/16 x 23/32 inch, hardened
24 1954280C1 2 WASHER, flat, pivot
25 432-612 2 PIN, SPLIT (COTTER), 3/32″ x 3/4″
28 96810C5 2 ARM, sector, window
29 1954277C1 2 COVER ASSY, arm, latch
30 175-466 2 SCREW, Sltd Truss Hd, 5/16″-18 x 5/8″, machine, truss head Phillips, 5/16 NC x 5/8 inch
1 1340194C1 1 GLASS, window, door
2 1340195C2 1 GLASS, windshield, upper
4 96902C1 2 SPACER, windshield, upper
5 262-15516 2 SCREW, SELF TAPPING, Hex Pan Hd, #10 x 1″, self-tapping, pan Phillips, No. 10-16 x 1 inch
8 1340196C1 1 GLASS, lower, windshield, left
9 1340197C1 1 GLASS, lower, windshield, right
11 1981771C2 1 SEAL, windshield
12 1340200C1 1 GLASS, CAB, window, left rear side
13 97268C1 4 SPACER, bonded glass, adhesive back, door window
1 1340289C1 1 MAT, FLOOR, front (Without foot throttle)
1 1955101C2 1 MAT, FLOOR, front (With foot throttle) not shown
2 104596A1 1 MAT, FLOOR, rear
3 97118C2 1 PAD, floor mat, front (Without foot throttle)
3 1955102C1 1 PAD, floor mat (With foot throttle) not shown
4 97122C1 1 PAD, floor mat, front corner
5 104597A1 1 MAT, FLOOR, PAD – rear
6 1971248C1 1 PLATE, LARGE, BARRIER – noise, front (Without foot throttle)
6 1955100C1 1 INSULATOR, BARRIER – noise, front (With foot throttle) not shown
7 104599A1 1 ANTISQUEAK, BARRIER – noise, rear
8 1971249C1 1 PLATE, LARGE, BARRIER – noise, front corner
9 104600A1 1 PLATE, LARGE, BARRIER – noise, right-hand console
10 1977905C2 2 PAD, front mount cover
1 1999971C3 1 PADDING, COVER – rear cab post, right-hand
3 1999972C1 1 PADDING, COVER – front cab post, right-hand
4 1990953C1 2 SCREW, Phillips washer, No. 10-24 x 1 inch (Gray)
7 96720C2 1 COVER ASSY, front cab post, lower, left-hand, lower
8 96719C3 1 COVER ASSY, front cab post, left-hand, upper
10 96717C4 1 COVER ASSY, crown fender
11 96716C1 1 COVER ASSY, center cab post
13 1990584C1 1 COVER ASSY, rear cab panel, if equipped
15 96735C2 1 COVER ASSY, rear cab post, left-hand
16 1999998C1 1 COVER ASSY, rear sill, lower
17 97227C2 1 PANEL ASSY., trim, cab, middle, INCLUDES: DECAL
19 96715C2 1 PANEL ASSY., rear corner, left-hand, trim
20 1958720C1 1 STUD, ball, external thread
21 1990952C1 2 SCREW, Phillips washer, No. 10-16 x 1 inch (Gray)
22 1977665C1 1 PAD, console fender, right-hand
23 1977664C1 1 PAD, fender, front top, right-hand
24 1977916C1 1 PAD, fender, center, right-hand
25 1977918C2 1 PAD, INSULATOR – fender, lower rear, right-hand
26 1344390C1 1 PANEL, PAD – rear trim, right-hand
27 123346A2 1 SEAL, grommet, rear access panel
28 123081A1 1 ANGLE, mounting
29 112332A1 1 SEAL, access panel
31 261-1456 2 SCREW, SELF TAPPING, Cross Pan Hd, #10 x 3/8″
1 96753C1 1 PANEL ASSY., HEADLINER – cab, front
2 104033C2 6 SCREW, SELF TAPPING, Cross Wash Hd, M4.8 x 19, Coated, self-tapping, truss head, No. 10-16 x
3 143309C1 2 SCREW, SELF TAPPING, Cross Pan Hd, #10-16 x 1/2″, self-tapping, pan Phillips head, No. 10-16 x
4 97172C1 2 SCREW, SELF TAPPING, Cross Pan Hd, #10-16 x 1″, pan head cross slot tap
7 97168C1 1 STRIP, SEAL – foam, 1100 mm (43-5/16 inch) long, cut from 187874C1 bulk seal, see below
8 98390C1 2 STRIP, SEAL – 13 (1/2) wide x 1000 (39-3/8) long x 25 mm (1 inch) thick, cut from 1974884C1 bulk
9 1958752C1 8 PORT, LOUVER – bezel, front window
11 97201C1 4 CLIP, spring, U-shaped
12 97016C1 1 ANGLE, SUPPORT – front, headliner left-hand
13 143309C1 3 SCREW, SELF TAPPING, Cross Pan Hd, #10-16 x 1/2″, self-tapping, pan Phillips head, No. 10-16 x
15 97024C1 1 SUPPORT ASSY., headliner, rear, left-hand
16 1330157C1 2 NUT, self-locking, hex flange, special, 1/4 inch NC
17 96979C1 1 GRILLE, speaker, left-hand
18 96980C1 1 GRILLE, speaker, right-hand
19 97058C1 8 CLIP, spring, retaining
22 96813C2 1 PANEL ASSY., switch
23 1270762C1 6 SCREW, SELF TAPPING, pan head Phillips, self-tapping, No. 10-16 x 3/4 inch
24 1983391C1 1 LAMP, dome, Includes: Ref. 25
25 E35556 1 BULB, lamp
26 83882C91 1 LAMP, ASSEMBLY – console illumination, console, Includes: Ref. 27, 28
27 D71346 1 LAMP, TAIL, lamp, No. 168
28 107329C1 1 HARNESS, WIRE, AND CABLE – bulb
29 1327506C1 2 SCREW, SELF TAPPING, Cross Pan Hd, M4.8 x 19, Coated, Replaces 104033C2 screw
30 92100C2 1 SWITCH, blower
31 92101C1 1 SWITCH, thermostat
32 122579A1 1 SWITCH, PRESSURE, low pressure, air conditioner
33 92115C2 1 SWITCH, wiper, windshield
35 1964672C1 1 LIGHT, indicator, amber, 14 volt, air conditioner
36 96893C1 4 KNOB, control, switch
37 1977668C1 1 FOAM, PAD – headliner, front
38 240873A1 1 PADDING, HEADLINER – cab, rear, used on models with round speakers, Includes: Ref. 39, 40
39 117987C1 6 NUT, U-type, No. 10-16, not shown
40 199740A1 8 RETAINER, NUT – U-type, No. 8-32, not shown
1 355190A1 1 BLOWER, cab, air, component parts are not serviced separately, replaces 1977564C2 blower
2 97006C1 4 BOLT, BOLT – hex flange, special, 6 – 1 x 20 mm
3 97005C1 4 NUT, hex flange, self-locking, special, 6 mm – 1
4 1343938C2 1 RESISTOR, blower
5 30495R1 2 SCREW, Cross Pan Hd, M3 x 12, pan head, 3 x 12 mm
6 824-1403 2 NUT, M3, Cl 5
7 240877A1 1 SUPPORT, blower
8 231-5144 10 NUT, Flg, USR, 1/4″-20
9 97198C2 2 SEAL, 1080 mm (42-17/32 inch) long, cut from 195917C1 bulk seal, see below
10 245358A1 2 SEAL, 371 mm (14-5/8 inch) long, cut from 182747C1 bulk seal, see below
11 1954714C1 2 EDGE, TRIM – 41mm (1-5/8 inch) long, cut from 1327666C1 bulk trim, see below
12 303748A1 2 FILTER, CAB, air, cab, replaces 240883A1 filter
13 240866A1 1 PANEL, ASSEMBLY – inner roof, Includes: Ref. 14-14C
14 97176C1 23 STUD, inner roof panel
15 231-5144 7 NUT, Flg, USR, 1/4″-20
16 97199C1 1 STRIP, SEAL – 1750 mm (68-29/32 inch) long, cut from 182747C1 bulk seal, see below
17 97200C1 1 STRIP, SEAL – 4440 mm (174-13/16 inch) long, cut from 182747C1 bulk seal, see below
18 1330955C2 15 RIVET, mandrel, 3/16 inch
19 1331102C2 2 GRILLE, LOUVER – air recirculation
20 97212C1 12 SCREW, pan head, No. 6-20 x 7/8 inch
22 240885A1 1 PANEL ASSY., recirculated air filter
23 240886A1 2 FILTER, recirculated air
24 97135C1 3 KNOB, recirculation panel
28 417-440 2 BOLT, Sq Hd, 1/4″-20 x 2 1/2″, G2, BOLT – square head, 1/4 NC x 2-1/2 inch, grade 2
29 1971364C1 2 RETAINER, bolt
34 169850C2 2 CLIP, CABLE, CLIP – retaining, inner roof panel, right-hand side
35 1977988C1 4 FOAM, PAD – foam, filler
36 362123R1 3 CLIP, harness
1 1990757C1 1 EVAPORATOR, ASSEMBLY – air conditioning and heater, see page 9-101 for valve and seals
2 1954493C1 1 HOSE, 3505 mm (138 inch) long, cut from 97252CX bulk hose, see below, heater supply
3 96880C2 1 HOSE ASSY., heater, replaces 96881C2 hose
4 1301342C1 1 FITTING, ADAPTER – straight, special
5 1954736C1 8 CLAMP, HOSE, adjustable
6 1331087C1 1 VALVE, CONTROL, control, heater
7 97116C1 1 BRACKET, SUPPORT – heater valve
8 260-5448 2 SCREW, SELF TAPPING, Cross Pan Hd, #8 x 1/2″, Phillips
9 473321C1 5 STRAP, CABLE, .098″ x 8″, tie
12 96893C1 1 KNOB, control
13 96879C1 1 LEVER, heater control
14 109311H 1 NUT, hex, jam, 7/16-28 NF
15 96877C2 1 CABLE PULLING GRIP, heater control
16 1954626C1 1 CLAMP, CLIP – retaining
17 96880C2 1 HOSE ASSY., heater, core to valve
18 1954494C1 1 HOSE, LARGE, 4267 mm (168 inch) long, cut from 97252CX bulk hose, see below, return
19 107107A1 1 VALVE, SHUT-OFF, water shutoff, right-hand side
20 105581A1 1 CONNECTOR, BUSHING – pipe reducer, 1/2 x 3/8 inch
21 1348531C1 1 ADAPTER, ELBOW – 45 degree, 1/2 NPT x 5/8 inch hose, left-hand side
1 1990757C2 1 EVAPORATOR, ASSEMBLY – air conditioning and heater, Includes: Ref. 1A, 2, 3
1 128485A1 1 O-RING, 9/16 ID x 1/16 inch wide
2 128484A1 1 O-RING, 7/16 ID x 1/16 inch wide
3 1990756C2 1 VALVE, expansion
4 98357C1 1 SEAL, 13 (1/2) x 790 (31-3/32) x 25 mm (1 inch) thick, cut from 1974884CX seal, see below
5 1954790C1 1 GROMMET, rubber, evaporator tubes
6 83822C1 1 TAPE, ADHESIVE, 610 mm (24 inch) long, rubber, insulator
7 1266352C2 2 HOSE, LARGE, 2290 mm (90-5/32 inch) long, cut from 87769CX bulk hose, see below, condensate
8 123329A1 1 HOSE, 1790 mm (70-15/32 inch) long, discharge, R12 refrigerant applications only, see 123329A2
8 123329A2 1 HOSE, 1790 mm (70 – 15/32 inch) long, discharge, 134A or R12 refrigerant applications, Includes: Ref.
9 128485A1 2 O-RING, 9/16 ID x 1/16 inch wide
10 1250594C2 2 CORE, VALVE –
11 122553A1 1 CAP, sealing, low side service port
12 128483A1 1 O-RING, 5/16 ID x 1/16 inch wide, at pressure switch fitting
17 1999928C1 1 HOSE, 1760 mm (69-19/64 inch) long, cab liquid, Includes: Ref. 18
18 128483A1 2 O-RING, 5/16 ID x 1/16 inch wide
19 1974764C1 2 FITTING, drain, condensate hose
20 1340439C1 2 WASHER, drain, for service order 238-5210 O-ring
21 1340438C1 2 NUT, drain fitting
1 1999922C1 1 HOSE, 1650 mm (65 inch) long, suction, compressor to cab base, R12 refrigerant applications only, no
1 1999922C2 1 HOSE, 1650 mm (65 inch) long, suction, compressor to cab base, 134A and R12 refrigerant
2 128485A1 1 O-RING, 9/16 ID x 1/16 inch wide, at compressor
3 1250594C2 1 CORE, VALVE –
4 122553A1 1 CAP, sealing
5 232948A1 1 SWITCH, PRESSURE, high,400 psi, replaces 375 psi switch used on some models
6 181583A1 1 CONDENSER, air conditioning, see Figure 5-18 for hardware attaching condenser to oil cooler, see
7 192929A2 1 HOSE, 413 mm (16-17/64 inch) long, condenser to receiver-drier, Includes: Ref. 8
8 128483A1 2 O-RING, 5/16 ID x 1/16 inch wide
9 223357A1 1 FIXING BRACKET, CLAMP – retaining
14 1954490C2 1 CLAMP, retaining
15 413-816 1 BOLT, Hex, 1/2″-13 x 1″, G5, Full Thd
16 80679 1 WASHER, LOCK, 1/2″
17 425-108 1 NUT, 1/2″-13, G5
18 1954766C2 1 CLAMP, retaining
19 762-24613 2 SCREW, SELF TAPPING, Flat Hd, M6 x 13, special, 6 x 13 mm
30 1990758C2 1 RECEIVER-DRYER, air conditioning
31 T102980 1 CLAMP, BRACKET – receiver-drier mounting
33 276-14832 1 SCREW, SELF TAPPING, Hex Hd, 5/16″ x 2″, self-tapping, hex head, 5/16 x 2 inch
35 131249A2 1 HOSE, 2800 mm (110-1/4 inch) long, receiver-drier to cab, Includes: Ref. 36
36 128483A1 1 O-RING, 5/16 ID x 1/16 inch wide
41 186468A2 1 HOSE, 1500 mm (59-1/16 inch) long, discharge, compressor to condenser, R12 refrigerant
41 186468A3 1 HOSE, 1500 mm (59-1/16 inch) long, discharge, compressor to condenser, 134A and R12 refrigerant
42 128484A1 1 O-RING, 7/16 ID x 1/16 inch wide, at condenser
43 128483A1 1 O-RING, 5/16 ID x 1/16 inch wide, at pressure switch fitting
44 1250594C2 2 CORE, VALVE –
45 122554A1 1 CAP, sealing, charge port
46 128485A1 1 O-RING, 9/16 ID x 1/16 inch wide, at compressor
47 234017A1 2 SCREW, BOLT – hex socket, 8 – 1.25 x 16 mm, mounts hoses to radiator, replaces 844-8016 bolt
1 A189155 1 PULLEY, compressor drive
3 131403C1 1 BELT, drive, 38-/12 inch long, compressor
4 237872A1 1 BRACKET, mounting, compressor
5 614-10035 3 BOLT, Hex, M10 x 35, 8.8, Full Thd, If used
5 854-10035 3 BOLT, Hex Flg, M10 x 35, 10.9, BOLT – hex flange head, 10 – 1.5 x 35, class 10.9, if used, brace to
6 892-11010 3 WASHER, LOCK, M10
8 825-1410 3 NUT, M10, Cl 8, If used
8 829-2310 3 NUT, M10 x 1.5, Flg, Cl 10, If used, Brace to Compressor and Compressor to Bracket
11 905-10025 4 BOLT, Hex Serr Flg, M10 x 25
14 84716C1 1 SUPPORT, STRAP – adjusting
15 905-10025 1 BOLT, Hex Serr Flg, M10 x 25
19 L18337 2 STRAP, CABLE, 9.95″-12.1″ lg, tie, 15 inch
21 135324A1 1 CLUTCH, ASSEMBLY – compressor
22 A49667 1 PLUG, hex, oil filler
23 128483A1 1 O-RING, 5/16 ID x 1/16 inch wide
7 895-15010 6 WASHER, M11 x 24 x 2
1 1530998C1 2 SUPPORT ASSY., BRACKET ASSEMBLY – mirror, left-hand or right-hand, pivot bolt has an M22 head
1 1530998C2 2 ARM, BRACKET ASSEMBLY – mirror, left-hand, pivot bolt has an M13 head on bolt, 258476A1 is a
2 185773A1 2 MIRROR ASSY., rear view, INCLUDES: CLAMP, MIRROR, BOLT, WASHER, CAP, BUSHING
3 256320A1 6 SCREW, BOLT – hex, full threads, 8 – 1.25 x 20 mm, zinc cobalt plate, replaces 614-8020 bolt
4 256402A1 6 WASHER, flat, 9 x 17 x 1.6 mm, zinc cobalt plate, replaces 895-11008 washer
11 103212A1 1 BAR, monitor mounting, 356 mm (14-1/64 inch) long, kit
12 614-10030 2 BOLT, Hex, M10 x 30, 8.8, Monitor mounting kit
13 825-1410 2 NUT, M10, Cl 8, Monitor mounting kit
14 895-18010 2 WASHER, M10 x 18 x 1.6, Monitor mounting kits
15 103213A1 2 HOLDER, BRACKET – mounting, monitor, kit
16 103226A1 2 CLAMP, mounting bracket, monitor kit
17 614-8025 4 BOLT, Hex, M8 x 25, 8.8, Monitor mounting kit
19 829-1408 4 NUT, M8, Cl 10, Monitor mounting kit
12 614-10030 2 BOLT, Hex, M10 x 30, 8.8, Monitor mounting kit
13 825-1410 2 NUT, M10, Cl 8, Monitor mounting kit
14 895-18010 2 WASHER, M10 x 18 x 1.6, Monitor mounting kits
15 103213A1 3 HOLDER, BRACKET – mounting, monitor, kit
16 103226A1 3 CLAMP, mounting bracket, monitor kit
17 614-8025 6 BOLT, Hex, M8 x 25, 8.8, Monitor mounting kit
19 829-1408 6 NUT, M8, Cl 10, Monitor mounting kit
18 895-11008 4 WASHER, M8 x 16 x 1.6, Monitor mounting kit
18 895-11008 6 WASHER, M8 x 16 x 1.6, Monitor mounting kit
2 248218A1 1 DECAL, 8930, Case IH, hood, left-hand side, if used
3 248221A1 1 DECAL, Case IH, 8930, hood, right-hand side, not shown, if used
4 248222A1 1 DECAL, 8940, Case IH, hood, left-hand side, if used
5 248223A1 1 DECAL, Case IH, 8940, hood, right-hand side, not shown, if used
6 248224A1 1 DECAL, 8950, Case IH, hood, left-hand side, if used
7 248225A1 1 DECAL, Case IH, 8950, hood, right-hand side, not shown, if used
8 197290A1 1 DECAL, door, stripe, right-hand side, silver outer stripe, if used
9 197291A1 1 DECAL, door, stripe, left-hand side, silver outer stripe, if used
10 1340033C3 1 DECAL, shift selector, (Without creeper)
11 1340034C3 1 DECAL, shift selector, (With creeper)
12 299289A1 1 DECAL, shift selector (With manual shuttle shift)
13 299293A1 1 DECAL, creeper control (With manual shuttle shift)
14 1334581C2 1 DECAL, 1 ISO, first coupler
15 1334582C2 1 DECAL, 2 ISO, second coupler
16 1334583C3 1 DECAL, 3 ISO, third coupler
17 1334584C3 1 DECAL, 4 ISO, fourth coupler
18 197289A1 1 DECAL, stripe, cab pillar, left-hand side, silver outer stripe, if used
19 197288A1 1 DECAL, stripe, cab pillar, right-hand side, silver outer stripe, if used
21 1968108C2 1 GUIDE, TRIM – hood sight
22 252725A1 1 SYMBOLS, EMBLEM – Magnum
1 128975A1 1 DECAL, fuse panel (French)
3 1954287C1 1 DECAL, lift to close, latch, front right window
3 1976753C1 1 DECAL, lift to close, latch, front right window (French), Part of the French language decal Kit P/N
4 1954288C1 1 DECAL, lift to close, latch, rear window
4 1976754C1 1 DECAL, lift to close, latch, rear window (French), Part of the French language decal Kit P/N
5 254018A1 1 DECAL, maintenance chart
7 111605A2 1 DECAL, employee involvement, quality assurance
8 1955349C1 1 DECAL, ether start
9 A189007 1 DECAL, warranty, fuel pump
10 321-4622 1 DECAL, push to unlock, instructions, hood unlatch
10 321-5625 1 DECAL, push to unlock, instructions, hood unlatch (French), Part of the French language decal Kit P/N
11 1968123C2 1 DECAL, negative jump start
11 1974534C1 1 DECAL, negative jump start (French), Part of the French language decal Kit P/N 1974527C2.
12 1955107C1 1 PLATE, LARGE, lamp switch cover
13 202013C2 1 TRAFFIC SIGNS, EMBLEM – slow moving vehicle
14 98000C1 3 SCREW, FASTENER – slow moving vehicle emblem
15 195-81005 3 WASHER, 3/8″ x 7/8″ x .083″, flat, 3/8 x 7/8 x 5/64 inch
16 1999943C1 1 DECAL, auxiliary valve control lever pattern, and sector
17 176262A1 1 DECAL, CE symbol, 60 mm
1 1960744C2 1 DECAL, Warning, avoid injury or death, always keep PTO driveline shields in place
1 1974530C2 1 DECAL, Warning, avoid injury or death, always keep PTO driveline shields in place (French), Part of
2 1968056C2 1 DECAL, Warning, avoid injury or death, before starting engine
2 1974538C1 1 DECAL, Warning, avoid injury or death, before starting engine (French), Part of the French language
3 321-3339 1 DECAL, Warning, be certain both latches are fully engaged across the implement lift pins
3 1974537C1 1 DECAL, Warning, be certain both latches are fully engaged across the implement lift pins (French)
4 321-6714 1 DECAL, Warning, batteries contain acid and explosive gas
4 321-6806 1 DECAL, Warning, batteries contain acid and explosive gas (French), Part of the French language decal
5 1334594C2 1 DECAL, Important, failure due to use of improper fluid, hydraulic fluid warranty
5 1334596C2 1 DECAL, Important, failure due to use of improper fluid, hydraulic fluid warranty (French), Part of the
6 1334627C2 2 DECAL, Important, when adjusting front wheel treads, MFD steering
6 1974531C1 2 DECAL, Important, when adjusting front wheel treads, MFD steering (French), Part of the French
7 A187743 1 DECAL, WARNING, Warning, to avoid possible eye damage from microwave signals emitted by this
7 A187756 1 DECAL, Warning, to avoid possible eye damage from microwave signals emitted by this sensor
8 J910778 1 DECAL, Caution, open during fill
8 1974544C1 1 DECAL, Caution, open during fill (French), Part of the French language decal Kit P/N 1974527C2.
9 1968008C1 1 DECAL, no step
9 1974542C1 1 DECAL, no step (French)
10 1342629C2 2 DECAL, precharge: only use dry nitrogen
11 1342630C2 2 DECAL, Caution, precharged to 135 psi
12 1334606C2 1 DECAL, Important, do not use the 540 rpm PTO for implements requiring more than 85 PTO
13 321-7040 1 DECAL, Danger, starting in gear can cause death, start engine only from operator seat, Part of the
13 142002A1 1 DECAL, Danger, starting in gear can cause death, start engine only from operator seat (French)
14 1975866C1 1 PLATE ASSY., cover, decal, radio opening, models without radio

Pages: 1 2 3 4

Leave a Reply

Your email address will not be published. Required fields are marked *